SERIES M Ku-BAND Rx / Tx ANTENNA SYSTEM
|
|
- Francis Ambrose Carter
- 5 years ago
- Views:
Transcription
1 June 15, 2011 REVISION D ASSEMBLY MANUAL SERIES M Ku-BAND Rx / Tx ANTENNA SYSTEM General Dynamics 1500 PRODELIN DRIVE NEWTON, NC 28658
2 PRODELIN CORPORATION SERIES M Ku-BAND Rx/Tx ANTENNA SYSTEM D Revised Company Name, Logo, and Part Tables 6/15/10 RAH C Rev. Assembly DWG Page 9 11/9/2001 CLT B Item 7 qty was 3. Added item 18 to tbl & dwg 02/20/98 PWG A REV. PG. 8 ITEMS 8, 14, /13/95 R Frye - ORIGINAL RELEASE 5/5/95 R FRYE REV. DESCRIPTION DATE APPROVED
3 TABLE OF CONTENTS SECTION I TITLE INTRODUCTION 1.0 GENERAL INFORMATION 1.1 UNPACKING & INSPECTION 1.2 FREIGHT DAMAGE 1.3 MATERIAL MISSING OR DAMAGED 1.4 MECHANICAL INSTALLATION TOOLS II ANTENNA SYSTEM ASSEMBLY 2.0 ANTENNA ASSEMBLY 2.1 FEED ASSEMBLY III SATELLITE ALIGNMENT 3.0 SATELLITE ALIGNMENT IV MAINTENANCE 4.0 MAINTENANCE OVERVIEW 4.1 PERIODIC INSPECTION 4.2 REFLECTOR 4.3 MOUNT & REFLECTOR SUPPORT 4.4 FEED & FEED SUPPORT 2
4 3
5 SECTION I INTRODUCTION 1.0 GENERAL INFORMATION This manual describes the assembly and installation of General Dynamics' 1.2 meter antenna system. The General Dynamics 1.2 meter is a rugged, reliable antenna system, which will operate in the Ku-Band frequency with high efficiency and at the same time successfully withstand the effects of the environment. These instructions are listed by sections that cover all areas of assembly and installation. Additional sections are included in the manual to provide information on antenna alignment to the satellite and maintenance. 1.1 UNPACKING AND INSPECTION The system containers should be unpacked and inspected at the earliest date to insure that all material has been received and is in good condition. A complete packing list for each major component is supplied. 1.2 FREIGHT DAMAGE Any damage to materials while in transit should be immediately directed to the freight carrier. He will instruct you on matters regarding any freight damage claims. 1.3 MATERIAL - MISSING OR DAMAGED Any questions regarding missing or damaged materials that is not due to the freight carrier should be directed to General Dynamics' Customer Service Department at: General Dynamics 1500 PRODELIN DRIVE NEWTON, NC (828)
6 1.4 MECHANICAL INSTALLATION TOOLS The following tools are suggested for the antenna installation. 1 RATCHET 1 SOCKET, - 7/16" 1 SOCKET - 1/2" 1 SOCKET, - 9/16" 1 SOCKET, - 3/4" 1 WRENCH, COMBINATION - 7/16" 1 WRENCH, COMBINATION - 1/2" 1 WRENCH, COMBINATION - 9/16" 1 WRENCH, COMBINATION - 3/4" 1 WRENCH, ADJUSTABLE - 8" 1 COMPASS - FOR ALIGNMENT TO SATELLITE 1 INCLINOMETER - FOR ALIGNMENT TO SATELLITE 5
7 SECTION II ANTENNA SYSTEM ASSEMBLY 2.0 ANTENNA ASSEMBLY Refer to figures and 2.0-2, the parts list, and follow the instructions in the listed sequence. Do not tighten any hardware until instructed. The interface from the ground to the antenna mount is a 2-1/2" schedule 40 pipe (2.88" O.D.). A Suggested In-Ground Foundation is shown on page #7. It is assumed the mast pipe has been properly installed. STEP 1: STEP 2: STEP 3: STEP 4: STEP 5: STEP 6: Place the canister (item# 1) onto the mast pipe. Using a compass, aim the canister's high end tabs (see figure 2.0-1) toward the selected satellite. Insert the [6 ] 3/8-16 x 1.00" set screw assemblies (item# 6) and hand tighten. A ground strap may be attached as shown. See figure Attach the reflector support tube (item# 2) to the canister with [1] 1/2-13 x 3.25" bolt, [2] flatwashers, [1] lockwasher, and [1] hex nut (items# 13,14,15,16). See figure Attach the elevation channel (item# 3) between the [2] lower end tabs of the canister (oriented as shown) with [2] 3/8-16 x 1.00" bolts, [2] flatwashers, [2] lockwashers, and [2] hex nuts (items# 7,9,10,11). Place [1] 1/2-13 nut, then a narrow flatwasher (items# 8,16) well up onto the elevation rod (item# 4), insert the elevation rod through the elevation channel (plate end toward reflector support tube), and secure with another flatwasher and [1] 1/2-13 coupling nut (items# 14,17). See figure Attach the elevation rod to the reflector support tube with [1] 5/16-18 x 1.00" bolt, [2] flatwashers, [1] lockwasher, and [1] nut (item# 18,19,20,21). Find the three holes in the rim of the reflector (item# 5). Make sure the middle one of the three holes (bottom of reflector) is pointing down, lift, position and attach the reflector to the reflector support tube angles with the [4] 27/64-13 x 1-3/8" hi-lo screws (item# 12). DO NOT OVER TIGHTEN AS THIS WILL PERMANENTLY DAMAGE THE REFLECTOR. 6
8 2.1 FEED ASSEMBLY Refer to the manual shipped with your feed system. 7
9 SUGGESTED IN-GROUND FOUNDATION (MIN) 2 1/2 SCH 40 PIPE (2.88 O.D.) SECTION A - A 30.0 SEE NOTE #7 A A 45 NOTES: /2 schedule 40 pipe should conform with ASTM A53 2. All concrete should conform to building code standards and have a minimum compressive strength of 3000 PSI at 28 days. (Per ACI ) 3. Soil bearing capacity should be no less than 2000 PSF. 4-. Concrete should be poured against undisturbed soil. 5. Allow concrete 24 hours set time before installation of antenna. 6. The antenna should be properly grounded to meet applicable local codes. 7. Minimum depth as shown or extend to local frost line. 8. Foundation meets the design requirements as set forth by the uniform building code. (1982 edition) (GENERAL DYNAMICS DOES NOT REPRESENT OR WARRANT THAT ANY PARTICULAR DESIGN OR SIZE OF FOUNDATION IS APPROPRIATE FOR ANY LOCALITY OR EARTH STATION INSTALLATION.) 8
10 ANTENNA ASSEMBLY PARTS LIST ITEM# PART# DESCRIPTION QTY CANISTER REFLECTOR SUPPORT TUBE CHANNEL, ELEVATION ROD, ELEVATION ADJUSTMENT REFLECTOR, WHITE REFLECTOR, WHITE W/SHC ASSEMBLY, SET SCREW, 3/8-16 x 1.00" (W/ NUTS) BOLT, 3/8-16 x 1.00" FLATWASHER, NARROW, 1/2" FLATWASHER, 3/8" LOCKWASHER, 3/8" NUT, HEX, 3/ SCREW, x 1-3/8" HI-LO THREAD BOLT, 1/2-13 x 3.25" FLATWASHER, 1/2" LOCKWASHER, 1/2" NUT, HEX, 1/ NUT, COUPLING, 1/ BOLT, 5/16-18 X NUT, HEX, 5/ FLATWASHER, 5/ LOCKWASHER, 5/16 1 SELECTED SATELLITE LOW END HIGH OPTIONAL GROUND STRAP MAST PIPE FIGURE
11 FIGURE
12 SECTION III ANTENNA ALIGNMENT 3.0 ALIGNMENT TO SATELLITE The 1.2 meter offset reflector contains a 22.6 deg. elevation offset look angle. Therefore, when the reflector aperture is perpendicular to the ground, the antenna is actually looking 22.6 deg. in elevation. All electrical connections need to be properly completed before antenna alignment. STEP 1: Attach an inclinometer to the support tube as shown in figure Subtract 22.6 deg. (see paragraph above) from the elevation angle of the desired satellite. This is the desired adjusted elevation angle. STEP 2: STEP 3: STEP 4: STEP 5: Raise or lower the antenna to find the desired elevation angle by turning the 1/2" nuts located at the elevation channel. Position the top hex nut so it will not interfere with adjustment. Turn the bottom coupling nut clockwise to increase elevation and counterclockwise to decrease elevation. After the correct elevation angle is set, loosen the 3/8" set screws just enough to allow the antenna system to be rotated around the mast pipe. Sweep the antenna through azimuth until the signal is found and then lost. Mark this point and sweep back through azimuth until the signal is found and lost again. Center azimuth between the two points where signal is lost. Peak the antenna signal by fine adjustments made in both elevation and azimuth. Tighten all hardware used for adjustment. 11
13 INCLINOMETER ELEVATION HARDWARE FIGURE
14 SECTION IV MAINTENANCE 4.0 MAINTENANCE OVERVIEW After installation, the antenna requires only periodic inspection. It is anticipated that maintenance, if required, will be minimal and easily handled by a local or inhouse maintenance staff. The materials used in the construction of this Earth Station Antenna virtually eliminate any maintenance repairs. 4.1 PERIODIC INSPECTION It is suggested that a periodic inspection be performed at least every six months. NOTE: After any severe weather conditions, inspection of the antenna should be performed to determine if foreign objects have caused damage or if survival specifications have been exceeded. This inspection should include the following: STEP 1: STEP 2: STEP 3: STEP 4: Check all bolting locations - all bolts should be tight. Check all structural members - repair or replace if damaged. Check the foundation anchor bolts, if any - they must be secure and no failure signs in foundation. Check for corrosion - on the reflector structure and the mount. 4.2 REFLECTOR Prodelin's reflector does not require any maintenance. The composite construction of the reflector is virtually impervious to any damages that could be caused by weather or atmospheric conditions. It is only necessary to inspect for any physical damage done by vandalism or very severe weather conditions. Should any damage be detected to a portion of the reflector, contact the Customer Service Department at Prodelin for recommendations involving reflector repair. 13
15 4.3 MOUNT AND REFLECTOR SUPPORT STRUCTURE The mount and reflector support structure supplied with this antenna is of steel construction and has a hot-dip galvanized finish. If inspection shows any signs of structural failure, the mount members that are damaged should be repaired or replaced. CORROSION: Any corrosion on steel members may be repaired with a cold, zinc-rich galvanizing paint. 4.4 FEED AND FEED SUPPORT The feed support and feed rods should be inspected to insure that all hardware is secure. The feed/radio mounting bolts should be tight. The feed horn window should be inspected to insure that it is intact so that no moisture can collect inside the feed horn. Replace if damaged. 14
1.8 METER SERIES 1194 ANTENNA SYSTEM
January 14, 2002 REVISION G ASSEMBLY MANUAL 1.8 METER SERIES 1194 ANTENNA SYSTEM PRODELIN CORPORATION 1500 Prodelin Drive Newton NC 28658 1.8 METER SERIES 1194 ANTENNA SYSTEM G Revise Address 1/14/02 F
More information1.8 METER SERIES 1184 ANTENNA SYSTEM
REVISION F January 10, 2002 ASSEMBLY MANUAL 1.8 METER SERIES 1184 ANTENNA SYSTEM PRODELIN CORPORATION 1500 Prodelin Drive Newton NC 28658 1.8 METER SERIES 1184 ANTENNA SYSTEM F Revised Address 1/10/02
More information.98M Ku-BAND Rx/Tx ANTENNA SYSTEM
Revision C January 2, 2002 ASSEMBLY MANUAL ANTENNA SYSTEM PRODELIN CORPORATION 1500 Prodelin Drive Newton NC 28658 ANTENNA SYSTEM C Revised Series text B Revised Address 1/2/02 RAH A Revise and Update
More information1.2M Ku-BAND Rx/Tx SERIES 1132 ANTENNA SYSTEM
August12, 2003 ASSEMBLY MANUAL Revision E 1.2M Ku-BAND Rx/Tx SERIES 1132 ANTENNA SYSTEM PRODELIN CORPORATION 1500 Prodelin Drive Newton NC 28658 1.2M Ku-BAND Rx/Tx SERIES 1132 ANTENNA SYSTEM E Revised
More information1.2 METER SERIES 1130 Rx/O ANTENNA SYSTEM
REVISION H April 20, 2016 ASSEMBLY MANUAL 1.2 METER SERIES 1130 Rx/O ANTENNA SYSTEM General Dynamics SATCOM Technologies 1700 Cable Drive NE Conover NC 28613 USA Phone 770-689-2040 www.gdsatcom.com 1.2
More information1.2M Ku-BAND Rx/Tx SERIES 1134 ANTENNA SYSTEM
August 21, 1997 Revision D ASSEMBLY MANUAL 1.2M Ku-BAND Rx/Tx SERIES 1134 ANTENNA SYSTEM PRODELIN CORPORATION 1700 NE CABLE DRIVE CONOVER, NC 28613-0368 1.2M Ku-BAND Rx/Tx SERIES 1134 ANTENNA SYSTEM D
More information.84M Ku-Band Rx/O Antenna System
4096-644 Revision A May 9, 2003 ASSEMBLY MANUAL.84M Ku-Band Rx/O Antenna System PRODELIN CORPORATION 1500 PRODELIN DRIVE NEWTON, NC 28658 .84M Ku-Band Rx/O Antenna System A ORIGINAL RELEASE 5/9/2003 A.Hahn
More information2.4 Meter 4 Piece C-Band Rx/Tx Antenna Feed System
4096-354 Revision B July 14, 2009 ASSEMBLY MANUAL 2.4 Meter 4 Piece C-Band Rx/Tx Antenna Feed System General Dynamics 1500 PRODELIN DRIVE NEWTON, NC 28658 2.4 Meter C-Band Rx/Tx Antenna Feed System B Revised
More informationHANDLING AND ASSEMBLY INSTRUCTIONS FOR TRUE FOCUS 3.0M, 3.8M AND 4.2M ANTENNAS WITH POLAR MOUNT
HANDLING AND ASSEMBLY INSTRUCTIONS FOR TRUE FOCUS 3.0M, 3.8M AND 4.2M ANTENNAS WITH POLAR MOUNT Introduction SECTION 1 Thank you for purchasing one of our fine True Focus products. This manual covers the
More informationKU-BAND FEED INSTALLATION OMT INTERFACE
Revision D April 22, 2016 Assembly Manual KU-BAND FEED INSTALLATION OMT INTERFACE General Dynamics SATCOM Technologies 1700 Cable Drive NE Conover NC 28613 USA Phone 770-689-2040 www.gdsatcom.com KU-BAND
More informationInstruction and Assembly Manual 1 - Compass 1 - Clinometer 1-9 Magnetic Bubble Level 1 - Torque Wrench (Capacity 4 Ft-lbs Ft-lbs)
Instruction and Assembly Manual 1 - Compass 1 - Clinometer 1-9 Magnetic Bubble Level 1 - Torque Wrench (Capacity 4 Ft-lbs - 175 Ft-lbs) ASSEMBLY TOOLS REQUIRED 1 - ¹⁵ ₁₆ Deep Socket (¹ ₂ Drive) 1 - ⁷ ₁₆
More informationStandard Pole Mount Parabolic Antenna Mounting Instructions 3 ft. (90cm) & 4 ft. (120cm)
495 R Billerica Ave. N. Billerica, MA 01862 USA Tel: (978) 459-8800 Fax: (978) 459-3310 / 8814 www.radiowavesinc.com email: sales@radiowavesinc.com Standard Pole Mount Parabolic Antenna Mounting Instructions
More informationANTENNA SYSTEMS. 1.8m Offset Rx & TxRx Antenna INSTALLATION & ASSEMBLY INSTRUCTIONS
ANTENNA SYSTEMS.m Offset Rx & TxRx Antenna INSTALLATION & ASSEMBLY INSTRUCTIONS LIMITED TWELVE () MONTH WARRANTY This PATRIOT ANTENNA equipment is warranted to be free from defects in material and workmanship
More informationM2 Antenna Systems, Inc. Model No:
M2 Antenna Systems, Inc. Model No: 400-600-10 SPECIFICATIONS: Model... 400-600-10 Frequency Range... 390 To 650 MHz *Gain... 12 To 13 dbic Front to back... 20 db Nominal Beamwidth... 46 Nominal Feed Impedance....
More informationType Meter Offset Transmit Receive Antenna System
+40 Assembly Instructions Type 243 2.4 Meter Offset Transmit Receive Antenna System 8000450-03 Skyware Global 1315 Industrial Park Drive Smithfield, NC 27577 Telephone: +1-919-934-9711 Internet: www.skywareglobal.com
More informationInstruction Sheet RADIO FREQUENCY SYSTEMS. Install. Instr. for Microwave Parabolic Antennas 2.4 m (8 ft) No Rev.
Instruction Sheet No. 412764 Rev. B ECO 12469 Install. Instr. for Microwave Parabolic Antennas 2.4 m (8 ft) These Installation Instructions are valid for antennas in the following version: reflector 2.4
More informationQDV120 Operation and Pointing manual
QDV120 Operation and Pointing manual MPAD1 Plus OP-080316-E1 page 1 Contents Item Description Page 1.0 Health and Safety for Operators and Installation Staff 3 2.0 Transit case Reflector/Mount/BUC/LNB
More information2005 ODU Point & Peak Job Aid
Summary This Job Aid covers: Preparing the Antenna for Pointing and Peaking Point Elevation Set the Skew Point Azimuth Peak Azimuth Peak Elevation Push/Pull Test This Job Aid supports all Technician audiences.
More informationINSTRUCTION AND ASSEMBLY MANUAL
INSTRUCTION AND ASSEMBLY MANUAL TYPE 243 2.4m Offset Tx/Rx Antenna System 2003 Channel Master LLC 8000450-03 ECN 9000000 5/03 US Sales Office 1315 Industrial Park Drive, Smithfield, NC 27577 USA Telephone:
More information2009 ODU Point and Peak Job Aid
Summary This Job Aid covers: Preparing the Antenna for Pointing and Peaking Point Elevation Set the Skew Point Azimuth Peak Azimuth Peak Elevation Push/Pull Test This Job Aid supports all Technician audiences.
More informationRIDGE MAST MOUNT (RMM)
May 5, 009 Revision E ASSEMBLY MANUAL (RMM) General Dynamics Satcom Technologies 1500 PRODELIN DRIVE NEWTON NC 8658 88-464-4141 www.gdsatcom.com 1.0 INTRODUCTION: 1.1 Features: The Ridge Mast Mount (RMM)
More information4-PC 2.4M ANTENNA SYSTEM W/DUAL AXIS TRACKING MOUNT
4096-536 Revision E July 13, 2000 ASSEMBLY MANUAL 4-PC 2.4M ANTENNA SYSTEM W/DUAL AXIS TRACKING MOUNT PRODELIN CORPORATION 1500 Prodelin Drive Newton NC 28658 4096-536 PRODELIN CORPORATION 2.4M DUAL AXIS
More informationInstruction and Assembly Manual
Instruction and Assembly Manual.90m, 1.0m & 1.2m SMC ANTENNA SYSTEM WITH AZ/EL CAP MOUNT TYPE 900 -.9m TYPE 100-1.0m TYPE 120-1.2m SMC ANTENNA WITH AZ/EL CAP MOUNT (UK) Limited Premier Business Park, Croft
More informationFoundation Specifications
Installation Instructions Foundation Specifications for Type ES45T-T and ES45T-R 4.5-Meter Earth Station Antennas Bulletin 37690B Revision H 1.0 INTRODUCTION 1.1 This document specifies typical foundation
More informationType 100 and Type 120 SMC Antenna System 1.0 Meter and 1.2 Meter Reflector with Az/El Cap Mount
Assembly Instructions Type 100 and Type 120 SMC Antenna System 1.0 Meter and 1.2 Meter Reflector with Az/El Cap Mount 8000284-01 Skyware Global 1315 Industrial Park Drive Smithfield, NC 27577 USA Telephone:
More informationInstallation Instructions TMW Antenna Tower Mount for 4ft (1.2m) Antennas.
Description The following pages show the steps required to assembly and fit the antenna mount to a vertical tower pipe of diameter 48 to 115 mm (1.9 to 4.5"). This mount provides ±20 azimuth or ±15 elevation
More informationTerminus TM CEN End Terminal
Product/Installation Manual Corporate Offices: 35 East Wacker Dr., 11 th Floor Chicago, IL 60601-2076, USA Tel: +1 (312) 467-6750 Fax: +1 (312) 467-1356 http://www.energyabsorption.com/ Quixote Europe
More informationFoundation Specifications for Type ES45T-T and ES45T-R 4.5-Meter Earth Station Antennas
Installation Instructions Foundation Specifications for Type ES45T-T and ES45T-R 4.5-Meter Earth Station Antennas Bulletin 37690B Revision F 1.0 INTRODUCTION 1.1 This document specifies typical foundation
More informationLIGHT BEAM ANTENNA MaxRange Antenna Series Assembly Instructions MaxRange Plus Digital / High Definition Television Antennas
LIGHT BEAM ANTENNA MaxRange Antenna Series Assembly Instructions MaxRange Plus Digital / High Definition Television Antennas Assembly Instructions 1 MaxRange Plus Antenna These instructions will lead you
More informationInstallation Instructions
Installation Instructions For 4 foot / 1.2m Diameter Ultra-high Performance Antenna Model ADxxG-4-T2 Before Installation, please read the instructions carefully. This instruction guide covers the installation
More informationANTENNA EXPERTS. Website: AP MHz. 2.4 Meters 30dBi. Gain
ANTENNA EXPERTS E-mail: info@antennaexperts.in Website: www.antennaexperts.in AP-180030 1700 1900 MHz. 2.4 Meters 30dBi. Gain INSTALLATION MANUAL GRID PARABOLIC ANTENNA NOTICE: Installation, maintenance
More informationFootball Goal Posts MODEL SERIES: FGP400 and FGP600 series
Football Goal Posts MODEL SERIES: FGP400 and FGP600 series Installation and Maintenance Instructions Please read all instructions before attempting installation of these units SAVE THESE INSTRUCTIONS FOR
More informationRemarks: Before Installation, please read the instruction carefully.
30 cm antenna Z24A30T37301 Remarks: Before Installation, please read the instruction carefully. This instruction book is for the installation of 0.3m ultra-high performance microwave antenna. Installation,
More informationModels 2230 and 2240
Models 2230 and 2240 Overview... 2 Tools Needed... 2 Hardware...3 Assembly... 4-13 Installation... 14 Drawer Removal... 15 Operation... 15 Maintenance... 15 Accessories... 16 Limited Warranty... 16 Perform
More informationRemarks: Before Installation, please read the instruction carefully.
60 cm antenna Z24A60T37301 Remarks: Before Installation, please read the instruction carefully. This instruction book is for the installation of 0.6m ultra-high performance microwave antenna. Installation,
More informationTELEX, liutiiilio"i TELEX COMMUNICATIONS, INC ALDRICH AVE. SO. MINNEAPOLIS. MN USA
TELEX, liutiiilio"i TELEX COMMUNICATIONS, INC. 9600 ALDRICH AVE. SO. MINNEAPOLIS. MN 55420 USA INSTRUCTION MANUAL ORDER NO. 410 General This antenna is a five-element, Citizens Band beam with a forward
More information74CM KU-BAND TYPE 741 ANTENNA SYSTEM HIGH WIND with Factory Assembled Az/El Mount
JULY 2016 Revision A ASSEMBLY MANUAL 8001114-01 74CM KU-BAND TYPE 741 ANTENNA SYSTEM HIGH WIND with Factory Assembled Az/El Mount A ORIGINAL RELEASE - EC-02522 JUL 2016 R. Thompson REV. DESCRIPTION DATE
More information25000 Series Lo-T TM Butterfly Control Valve Instructions
November 2001 25000 Series Lo-T TM Butterfly Control Valve Instructions Instruction No. 25.1:IM PRELIMINARY STEPS Before installation, note the flow direction arrow on the valve body. The flow should enter
More informationMESA-HPX. Assembly and Installation Manual. w/appendix A for Prodelin Antenna. 901-Manual-MESA-HPX
MESA-HPX Assembly and Installation Manual w/appendix A for Prodelin Antenna 901-Manual-MESA-HPX Rev 30 March 2011 2 INDEX Installation Cautions 4 Installation Pole Height Orientation of the Mount on the
More informationInstallation Instructions
903-CIS0143-C Installation Instructions 0.9m Antenna LEAX Arkivator Telecom disclaims any liability for the results of improper or unsafe installation, inspection, maintenance, or removal practices. Torsgatan
More informationGared Pro-S Portable Backstop
Models: 9616 & 9618 Installation, Operation and Maintenance Instructions Please read all instructions before attempting installation or operation of these units SAVE THESE INSTRUCTIONS FOR FUTURE USE PUBLICATION
More informationInstruction Manual for 98cm Elliptical Ka Antenna
Instruction Manual for 98cm Elliptical Ka Antenna 98cm WB Issue 03 Caution This instruction leaflet will assist you in the correct installation of the product. Read it prior to starting any installation
More informationBASEBALL FOUL POLES GROUND SLEEVE MOUNTED
X X Page 1 of 6 GROUND SLEEVE INSTALLATION Ground Sleeve Foul Pole Size "A" F39901 32' and 40' 67 5/8" F39902 24' 67 5/8" F39903 16' 43 5/8" 00402000 12' 29 3/8" 7" ONE SET OF SLOTS MUST BE PARALLEL AND
More information75 cm ODU (VS1300 with the SurfBeam2 TRIA) Assembly Job Aid
Summary This Job Aid covers: Verify AZ/EL Assembly Alignment Antenna Back Bracket Assembly TRIA, TRIA Bracket, and Boom Arm Assembly This Job Aid supports all Technician audiences. This job aid covers
More informationInstallation Guide. Hiltron Motorized Antenna Mount HMAM
HMAM_Install_A.doc Page 1 of 20 Installation Guide for Hiltron Motorized Antenna Mount HMAM HMAM_Install_A.doc Page 2 of 20 Table of Contents 1 Overview...3 2 Unpacking and Inspection...3 3 Contents of
More informationANTENNA SYSTEMS. 67cm/84cm Offset Antenna Receive only and Transmit-Receive Micro-Terminal INSTALLATION & ASSEMBLY INSTRUCTIONS
ANTENNA SYSTEMS 67cm/84cm Offset Antenna Receive only and Transmit-Receive Micro-Terminal INSTALLATION & ASSEMBLY INSTRUCTIONS LIMITED TWELVE () MONTH WARRANTY This PATRIOT ANTENNA equipment is warranted
More informationFXL-168 FIXED RACK ASSEMBLY INSTRUCTIONS SALES ORDER #
ZOMEWORKS FXL-168 FIXED RACK ASSEMBLY INSTRUCTIONS SALES ORDER # 1 1011 Sawmill Road NW, PO Box 25805, Albuquerque, NM 87125 USA (505) 242-5354 / (800) 279-6342 / FAX (505) 243-5187 E-mail: zomework@zomeworks.com
More informationParadigm. Connect100 Installation Guide
Paradigm GX Connect100 Installation Guide Paradigm GX Safe Use WARNING Radiation Hazard. Transmitter power levels are sufficient to cause blindness or other serious injury to body tissue. Do not power
More information5/16" Flange nut. Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector zinc plated bolt w/ washers and nut. Anchor 3" sq. 7 Ga.
2 1/2" x 2 1/2" x 10 Ga. 6" 5" 4" Variable Slipbase (8" Sq. SYS.) 5/16 Corner Bolt W/ nut 5/16" Flange nut Stub Insert (8" Sq. SYS.) Bolt Keeper Plate (8" Sq. SYS.) (3) 1/2" x 3" Hex head connector zinc
More information75 cm ODU (VS1300) Assembly Job Aid
Summary This Job Aid covers: Verify AZ/EL Assembly Alignment Antenna Back Bracket Assembly Transport On Site Assembly This Job Aid supports all Technician audiences. This job aid covers the VS1200 ODU
More information75cm ODU/SurfBeam 2 Point and Peak Job Aid
Summary This Job Aid covers: 75cm ODU/SurfBeam 2 Point and Peak Job Aid Preparing the Antenna for Pointing and Peaking Configure the SurfBeam 2 Modem and 75cm TRIA Point Elevation Set the Skew Point Azimuth
More information3.8m Offset Antenna System Assembly Manual COMMUNICATIONS
3.8m Offset Antenna System Assembly Manual COMMUNICATIONS COMMUNICATIONS LIMITED TWELVE (12) MONTH WARRANTY This CHALLENGER COMMUNICATIONS, LLC ("CHALLENGER") equipment is warranted to be free from defects
More informationHARDINGE Installation booklet For: Dead-Length Collet Adaptation Chucks Stationary Collet
HARDINGE Installation booklet For: Dead-Length Collet Adaptation Chucks Stationary Collet Read the enclosed instructions and recommendations before any installations CONTENTS Dead-Length Collet Adaptation
More informationINSTRUCTION MANUAL VB-66DX. 6-Meter 6-Element Beam. Preparation For Assembly. General Description
VB-66DX 308 Industrial Park Road Starkville, MS 39759 USA Ph: (662) 323-9538 FAX: (662) 323-6551 6-Meter 6-Element Beam INSTRUCTION MANUAL General Description The Hy-Gain Model 66DX is a full sized 6-
More informationHITCH MOUNT BICYCLE CARRIER Model BC-102
HITCH MOUNT BICYCLE CARRIER Model BC-102 MAXIMUM LOADING CAPACITY 60 LBS Recommended Tools for Assembly: Open Wrench (2 pc.) Open Wrench (2 pc.) Open Wrench (2 pc.) Size=17mm Size=19mm Size=24mm Assembly
More informationFirst Team, Inc. WallMonster Series. Installation Instructions
First Team, Inc. WallMonster Series Installation Instructions Bill of Materials A (1) Wall Bracket B (2) Upper Extension Arms C (1) Lower Extension Arm Assembly D (1) H-Frame Backboard Mount E (1) 5/8
More informationHigh End Residential In-Ground Basketball System Owners Manual
High End Residential In-Ground Basketball System Owners Manual Customer Service Center N53 W24700 South Corporate Circle Sussex, WI 53089 U.S.A. Write Model Number From Box Here: READ AND UNDERSTAND OPERATOR'S
More informationModels 2030 and 2040
Models 2030 and 2040 Overview... 2 Tools Needed... 2 Hardware... 2 Assembly... 3-8 Installation... 9 Operation... 9 Maintenance... 10 Accessories... 10 Limited Warranty... 10 Document # 101290 0607 Printed
More informationThese Installation Instructions are valid for antennas in the following version:
Installation Instructions 4 ft CompactLine Antennas (with E-Mount 200 km/h) SB, SBX NMT 480-12(e) These installation instructions have been written for qualified, skilled personnel. The antenna shall be
More informationFoundation Specifications for 5.6-Meter Modular Earth Station Antennas
Installation Instructions Bulletin 237029 Foundation Specifications for 5.6-Meter Modular Earth Station Antennas Revision A Introduction This document specifies typical foundation characteristics, designs,
More informationHardware Pkg
ASSEMBLY INSTRUCTIONS Horse Shelter 12 x 15 76110678 Hardware Pkg. 76900228 THANK YOU FOR PURCHASING THIS PRODUCT For questions about this product, or parts inquiries, please contact our Customer Service
More informationHorse Shelter 12 x
Horse Shelter 12 x 15 76110678 Hardware Kit 76900228 THANK YOU FOR PURCHASING THIS PRODUCT Behlen Country has been in the business of providing quality products for more than 75 years. Our products will
More informationHARDINGE Installation booklet For:
HARDINGE Installation booklet For: L Flange Nose Dead-Length Collet Adaptation Chucks Draw Collet Read the enclosed instructions and recommendations before any installations WARRANTY & RETURN PROCEDURES
More information3.8m Commercial Antenna TxRx King Post Mount
ANTENNA SYSTEMS 3.8m Commercial Antenna TxRx King Post Mount INSTALLATION & ASSEMBLY INSTRUCTIONS LIMITED TWELVE (12) MONTH WARRANTY This PATRIOT ANTENNA equipment is warranted to be free from defects
More informationINSTRUCTION MANUAL. Model 18AVQII Five Band Vertical Antenna 10, 15, 20, 40, 80 Meter. General Description. Theory of Operation
Model 18AVQII Five Band Vertical Antenna 10, 15, 20, 40, 80 Meter 308 Industrial Park Road Starkville, MS 39759 (662) 323-9538 Fax: (662) 323-5803 INSTRUCTION MANUAL General Description The Hy-Gain 18AVQII
More information6o ft (18.3 m) Southwest Windpower, Inc West Route 66 Flagstaff, Arizona USA Phone: Fax:
6o ft (18.3 m) sectional MONOPOLE TOWER INSTALLATION MANUAL Southwest Windpower, Inc. 1801 West Route 66 Flagstaff, Arizona 86001 USA Phone: 928.779.9463 Fax: 928.779.1485 www.skystreamenergy.com 3-CMLT-1390-01
More informationLIGHT BEAM ANTENNA MaxRange Antenna Series Assembly Instructions MaxRange Ultra Digital / High Definition Television Antennas
LIGHT BEAM ANTENNA MaxRange Antenna Series Assembly Instructions MaxRange Ultra Digital / High Definition Television Antennas Assembly Instructions 1 MaxRange Ultra Antenna These instructions will lead
More informationFoundation Specifications for 7.6-Meter Modular Earth Station Antennas
Installation Instructions Foundation Specifications for 7.6-Meter Modular Earth Station Antennas Bulletin 237186A Revision A Introduction This document specifies typical foundation characteristics, designs,
More informationA 1 Vertical Pole I 1 BA47/47A/47P Backboard (2 req d on Model BA872)
Instruction Manual BA871, BA872 Ultimate Playground Basketball System Instructions Customer Service (800) 247-7668 P A R T S L I S T Item Qty Description Item Qty Description A 1 Vertical Pole I 1 BA47/47A/47P
More informationSTRATUS SHELTER. Take bike parking to new heights
Take bike parking to new heights The Stratus Shelter is a striking bike shelter option for any transit station, university campus, or multi-family residential building project. It is constructed of American
More informationRBP-1215B-RX DODGE RAM QUAD CAB RX3
RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side
More informationElliptical Unpacking and Installation Instructions
Elliptical Unpacking and Installation Instructions Use these instructions for the following Ellipticals: ClubStride 5100-LE Receiving When the carrier delivers your order, verify that the number of items
More informationModular XP Ramp Assembly Manual
Modular XP Manual 1 Contents Overview... 2-5 1.1 Tools required...6 1.2 Hardware list...6 Ramp & Platform Standard Parts 2.1 Ramp Parts...7 2.2 Platform Parts...8 2.3 Standard Platform Configurations...
More informationModels 2130 and 2140
Models 2130 and 2140 Overview... 2 Tools Needed... 2 Hardware... 2 Assembly... 3-10 Installation...11 Operation... 11 Maintenance... 12 Accessories...12 Limited Warranty... 12 Printed in USA 2007 Perform
More informationALUMINUM FOOTBALL GOALS INSTRUCTIONS WARNING WARNING Upright. Upright. Flag. Flag. Offset Pole.
ALUMINUM FOOTBALL GOALS INSTRUCTIONS 800-67-090 Flag Flag Ground Sleeve Anchor Kit WARNING Football goals are shipped unassembled. Read all instructions thoroughly before attempting to assemble this equipment.
More informationModels 2130 and 2140
Models 2130 and 2140 Overview... 2 Tools Needed... 2 Hardware... 2 Assembly... 3-10 Installation...11 Operation... 11 Maintenance... 12 Accessories...12 Limited Warranty... 12 Perform the following sequence
More informationFoundation Specifications
Installation Instructions Bulletin 237746 Foundation Specifications for High-Wind 4.5-Meter Earth Station Antennas Revision C 1.0 INTRODUCTION 1.1 This document specifies typical foundation characteristics,
More informationAmbient Weather EZ Weather Station Tripod and Mast Assembly for AcuRite Weather Stations User Manual
Ambient Weather EZ-48-100 Weather Station Tripod and Mast Assembly for AcuRite Weather Stations User Manual Table of Contents 1. Introduction... 1 2. Accessories... 1 3. Parts... 2 4. Warnings... 2 5.
More informationAssembly Instructions: Bencher Skylark
Assembly Instructions: Bencher Skylark Tools Required: Pop Rivet Tool Tape Measure Hex Wrenches Screwdriver Several Disposable Rags Two Saw Horses Several boxes or bowls to hold fasteners and small parts
More informationINSTRUCTION MANUAL V-42R. Dual Band Collinear Gain Vertical for MHz and GENERAL DESCRIPTION
308 Industrial Park Road, Starkville, MS 39759 USA Ph: (662) 323-9538 FAX: (662) 323-6551 V-42R Dual Band Collinear Gain Vertical for 144-148 MHz and 436-450 INSTRUCTION MANUAL GENERAL DESCRIPTION The
More informationAmbient Weather EZ Stable Mounting Kit with Mast for AcuRite Weather Stations User Manual
Ambient Weather EZ-30-12-100 Stable Mounting Kit with Mast for AcuRite Weather Stations User Manual Table of Contents 1. Introduction... 1 2. Accessories... 1 3. Parts... 2 4. Warnings... 2 5. Recommended
More informationWave Bike Rack specs SPECS AND INSTALL INSTRUCTIONS. Deluxe Wave Style Bike Rack. Series Names & Model # s. Product maintenance. Thermoplastic Coating
SPES ND INSTLL INSTRUTIONS Deluxe Wave Style ike Rack SKU: Series Names & Model # s 8 F7WIRQ InGround Post Mount Wave ike Racks Wave ike Rack specs KP/G3, KP/G5, KP/G7, KP/G9, KP/G11, KP/G13 Plate Surface
More informationTABLE OF CONTENTS REQUIRED TOOLS
TABLE OF CONTENTS SECTION SECTION TITLE PAGE NO. 1 2 3 4 5 Assembling Mounting Structure Installing Bicycle Supports Mounting Rack to Wall Adding Sections Customizing Rack Configuration REQUIRED TOOLS
More information1.2M KU-BAND TYPE 128 ANTENNA SYSTEM HIGH WIND with Factory Assembled Az/El Mount
September 2015 Revision A ASSEMBLY MANUAL 8001101-01 1.2M KU-BAND TYPE 128 ANTENNA SYSTEM HIGH WIND with Factory Assembled Az/El Mount A ORIGINAL RELEASE EC-02178 OCT 2015 R. Thompson REV. DESCRIPTION
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS PLATINUM 4 OVAL STEP BAR (90 BENT END) APPLICATION: 2010-2015 Dodge Ram 2500/3500 Mega Cab PART NUMBER: 21-3570, 21-3575, 23-3570, 23-3575, 25-3570, 25-3575,
More informationINSTRUCTION MANUAL ORDER NO. V3R MODEL V3R. Collinear Gain Vertical for MHz
ORDER NO. V3R MODEL V3R Collinear Gain Vertical for 216-225 MHz INSTRUCTION MANUAL General Description The new Hy-Gain V3R VHF antenna is a collinear 5/8-wave omnidirectional vertical antenna for the 216-225
More informationBISON GOOSENECK FOOTBALL 1 PAIR OF GOAL POSTS
Instruction Manual BISON GOOSENECK FOOTBALL 1 PAIR OF GOAL POSTS Customer Service (800) 247-7668 P A R T S L I S T Item Qty Description Item Qty Description A 2 GOOSENECK POLE I 4 UPRIGHTS B 2 BAND CLAMP
More informationPLAY HOUSE IMPORTANT
IMPORTANT Page 1 PLEASE READ THESE INSTRUCTIONS BEFORE COMMENCING ASSEMBLY. All equipment must be installed in accordance with these instructions. Check your shipment against Bill of Lading and Parts list.
More informationINSTRUCTION MANUAL. Specifications Electrical. Front-To-Back Ratio VSWR at Resonance Less than 1.5:1 Nominal Impedance. Mechanical
300 Industrial Park Road, Starkville, MS 39759 Ph: (662) 323-8538 FAX: (662) 323-6551 TH-3JRS Tri-band HF 3 Elements Beam Covers 10, 15 and 20 Meters INSTRUCTION MANUAL WARNING Installation of this product
More informationINSTALLATION INSTRUCTIONS
Sheet 1 of 5 General: Upon receipt of fixture thoroughly inspect for any freight damage, which should be brought to the attention of the delivery carrier. Compare the catalog description listed on the
More informationStar Trac Turbo Trainer Assembly & Setup
Star Trac Turbo Trainer Use the following procedures to unpack and assemble your Turbo Trainer manufactured by Star Trac. UNPACKING AND PARTS LIST Position the shipping carton so the Heavy End logo is
More informationInstallation Instructions HOSS Hardtop Organized Storage System
Installation Instructions HOSS Hardtop Organized Storage System Application: Hard Top and Doors Storage System Part Number: 42801 www.bestop.com - We re here to help! Visit our web site and click on Ask
More informationREAD ALL DIRECTIONS CAREFULLY BEFORE BEGINNING INSTALLATION
INSTRUCTIONS AND REPAIR PARTS LIST 2G - GRO-FAST TM HOG FEEDER - BROWER 2GP - GRO-FAST TM HOG FEEDER - PRIDE OF THE FARM READ ALL DIRECTIONS CAREFULLY BEFORE BEGINNING INSTALLATION TOOLS REQUIRED: Straight
More informationDirect Burial Floodlight - DBF Installation Instructions Above Grade Housing
P.O. Box 60080 16555 East Gale Ave. City of Industry, California 91716-0080 626/968-5666 FAX 626/330-3861 Direct Burial Floodlight - DBF Installation Instructions DBF10 / DBF710 WARNING: Fixtures must
More informationBill of Materials (per goal)
Bill of Materials (per goal) (1) Crossbar (6) ½ x 1 Hex Bolt (2) Upright Weldment (2) ½ x 6 ½ Hex Bolt Note: There is (1) left & (1) right Upright (6) ½ Lockwasher (2) Corner Splice (2) ½ Centerlock Nut
More informationFull Height Ladder Safety Gate
Full Height Ladder Safety Gate Installation Instructions/Operation and Maintenance Manual Models Powder Coat Yellow (PCY) 304 Stainless Steel (SS) Hot Dipped Galvanized (GAL) Table of Contents Product
More informationINSTALLATION & OWNER S MANUAL
Rev. O p. 1 of 16 INSTALLATION & OWNER S MANUAL V4213 BALL CAGE KIT INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave with the owner when installation
More informationH HD Adult Wheelchair Swing Frame & Hangers(perm) IMPORTANT
Page 1 IMPORTANT PLEASE READ THESE INSTRUCTIONS BEFORE COMMENCING ASSEMBLY. All equipment must be installed in accordance with these instructions. Check your shipment against Bill of Lading and Parts list.
More informationInstallation Instructions for the
Installation Instructions for the Standard AZ EL Mount Congratulations! You have now purchased the finest AZ-EL mount available. This unit has been designed to give you the most stable system to work on
More informationGENERAL INSPECTION AND MAINTENANCE PROCEDURE FOR FIXED HF ANTENNA SYSTEMS
Bulletin 7591056,Revision A 1. SCOPE GENERAL INSPECTION AND MAINTENANCE PROCEDURE FOR FIXED HF ANTENNA SYSTEMS It is the intent of this procedure that all equipment and components of the antenna system
More information