Appendix A: BLC-10/20/25 DC Models Packing

Size: px

Start display at page:

Download "Appendix A: BLC-10/20/25 DC Models Packing"

Edwin Daniel
5 years ago
Views:

1 Appendix A: BLC-10/20/25 DC Models Packing List BLC-10/20/25/40/50 User Manual Appendix A: BLC-10/20/25 DC Models Packing List Description Belcom P/N Quantity BLC-10/20/25 BLC 10/20/25 1 Installation Kit, including: - Mounting clamp - Hex nut, ¼"-20 with lock - Flat washer ¼ x 16 x 1 - Slotted washer NF GND screw - NF10-32x5/16 ST GND screw M1006INST - M100610P WG assembly kit A * Flex WG 0.96m * WG flex assembly kit A * Optional, not included in a standard kit. A-1

3 Appendix B: AC Models Packing List BLC-10/20/25/40/50 User Manual Appendix B: AC Models Packing List Description Belcom P/N Quantity BLC 10/20/25/40/50 AC BLC 10/20/25/40/50 AC Installation Kit, including: - Plug female 3P + PE - Sealing tape - Cord end terminals - Screw SCR SOC CAP ¼-20x30mm - Flat washer ¼ x 16 x 1 - Hex nut, ¼"-20 with lock - Shaft ¼-20x200mm - Installation flange - Installation spacer - Slotted washer NF GND screw - NF10-32x5/16 ST GND screw M1143INST JM M114310P011 M114310P WG assembly kit A * Flex WG 0.96m * WG flex assembly kit A * Optional, not included in a standard kit. B-1

5 Appendix C: BLC-40/50 DC Packing List BLC-10/20/25/40/50 User Manual Appendix C: BLC-40/50 DC Packing List Description Belcom P/N Quantity BLC-40/50 DC BLC 40/50 DC 1 Installation Kit, including: M1221INST 1 - Plug female 4P + PE Sealing tape Cord end terminals Screw SCR SOC CAP ¼-20x30mm Flat washer ¼ x 16 x Hex Nut, ¼"-20 with lock Shaft ¼-20x200mm JM Installation flange M114310P Installation spacer M114310P012 4 WG assembly kit A * Flex WG 0.96m * WG flex assembly kit A * Optional, not included in a standard kit. C-1

7 Appendix D: DC Power Inserter Packing List BLC-10/20/25/40/50 User Manual Appendix D: DC Power Inserter Packing List Description Belcom P/N Quantity DC Power Inserter 48V 350W A1007/AC230/DC48 1 Or: DC Power Inserter 24V 150W A1007/AC230/DC24 Modem cable, N Type Or: Modem cable, F Type A10621 AC power cord D-1

9 Appendix E: Control BLC-10/20/25/40/50 User Manual Appendix E: Control This appendix describes the Control connector functionality. Pin Name In/Out Function Logic Action 1. Status Out Fault summary "1" = Fault Mute 2. Over temperature Out Over temperature protection ** "1" = Fault Mute 3. Temperature warning 4. Power supply status Out Temperature warning ** "1" = Fault Indication only Out Internal power supply fault "1" = Fault Mute 5. Reflected power Out High reflected power "1" = Fault Indication only 6. * Fun status Out Fan rotation status "1" = Fault Mute 7. Total failure Out Total failure "0" = Fault Mute 8. Temperature Analog Out Out Temperature = (1000*V-790)/ V Analog Indication only 9. Mute In Mutes the BUC "0" = Mute Mute 10. Reference input status Out Reference threshold limit "1" = Fault Indication only 11. Output forward power Analog indication voltage, See appendix F 0-5 V Analog Indication only 12. Output reflected power Analog indication voltage, See appendix F 0-5 V Analog Indication only 13. GND * For BLC-40 and BLC-50 models, starting from S/N 200. ** BUCs with M&C only E-1

11 Appendix F: Detectors Calibration Tables BLC-10/20/25/40/50 User Manual Appendix F: Detectors Calibration Tables BLC-40/50 BLC-20/25 Forward power Reflected power Forward power Reflected power Vin [volt] P [dbm] Vin [volt] P [dbm] Vin [volt] P [dbm] Vin [volt] P [dbm] F-1

13 Appendix G: BLC-40/50 DC Cable Assembly BLC-10/20/25/40/50 User Manual Appendix G: BLC-40/50 DC Cable Assembly Part Number: 1221DCABLE # Name Description MFG Manufacturer P/N Belcom P/N QTY 1. DC connector Plug male 4P+PE OD 10-12mm 2. AC cable* Cable AC 4x2.5mm OD=11.5mm 3. End terminal Cord end terminal D=2.6mm L=7mm Binder LAPP GROUP KST (K.S.Terminals) OLFLEX ROBUST G OR Equivalent EN2507 OR Equivalent As required Sealing tape Sealing tape Le Mark RT24BLACK Meter * Not supplied Assembly: G-1

14 BLC-10/20/25/40/50 User Manual Appendix G: BLC-40/50 DC Cable Assembly 1. Seal the pins and seal the plug insert using RTV. 2. Make a sealing test. 3. Strip 40 mm from both sides of the DC Cable outer sleeve. 4. Strip 8 mm of insulation from every wire end. 5. Using a proper crimping tool, crimp the cord end terminals (supplied) on the wire stripped tips (four on each cable side). 6. Insert the cable through the connector record parts (1a, 1b, 1c, 1d). 7. At the connector side, insert each wire end terminal to the proper connector contact according to the schematics below. 8. Tight all terminal screws. 9. Assemble the connector. Tight the cable sleeve (1a) and pressing screw (1d) in order to assure sealing. 10. After connecting to the BUC, wrap the sealing tape around both the cable and the mating connector. Schematics: (Cords color are valid for the recommended cable) Connector Spare, Gray Spare PE (Protective Earth), Yellow&Green Positive (+), Brown Negative (-), Black ~ G-2

Appendix H: AC Cable Assembly - L-Shape Plug BLC-10/20/25/40/50 User Manual Appendix H: AC Cable Assembly - L-Shape Plug Part Number: 1143LACABLE-15M Name Description MFG Manufacturer P/N Belcom P/N

15 Appendix H: AC Cable Assembly - L-Shape Plug BLC-10/20/25/40/50 User Manual Appendix H: AC Cable Assembly - L-Shape Plug Part Number: 1143LACABLE-15M Name Description MFG Manufacturer P/N Belcom P/N QTY 1. AC connector Plug female 3P+PE L shape Cable OD = 6-8 mm 2. AC cable* Cable AC 3x1.5mm OD=6.8mm 3. End terminal Cord end terminal D=2.6mm L=7mm Binder LAPP GROUP KST (K.S.Terminals) OLFLEX ROBUST G or Equivalent EN2507 or Equivalent As required Sealing tape Sealing tape Le Mark RT24BLACK Meter *Not supplied Assembly: H-1

BLC-10/20/25/40/50 User Manual Appendix H: AC Cable Assembly - L-Shape Plug 1. Strip 40 mm from both sides of the AC Cable outer sleeve. 2. Strip 8 mm of insulation from every wire s end. 3.

16 BLC-10/20/25/40/50 User Manual Appendix H: AC Cable Assembly - L-Shape Plug 1. Strip 40 mm from both sides of the AC Cable outer sleeve. 2. Strip 8 mm of insulation from every wire s end. 3. Using a proper crimping tool, crimp the cord end terminals (supplied) on the wire stripped tips (four on each cable side). 4. Insert the cable through the connector record parts (1a, 1b, 1c, 1d). 5. At the connector side, insert each wire end terminal to the proper connector contact according to the schematics below. 6. Fasten all terminal screws. 7. In order to assure water drainage, the cable clamp should be pointed down when the plug is connected to the BUC. Rotate the clamp to the right direction before tightening the cable sleeve (1a) and pressing screw (1d). Assure sealing. 8. After connecting to the BUC, wrap the sealing tape around both the cable and the mating connector. CAUTION It is recommended to seal all the connectors on the BUC (i.e. the IF cable connector, the power supply and the M&C) using a sealing tape (such as LeMark PN RT24 or equivalent, see Figure 2-6). Schematics: (Cords color are valid for the recommended cable) H-2

17 Appendix I: AC Cable Assembly - Straight Plug BLC-10/20/25/40/50 User Manual Appendix I: AC Cable Assembly - Straight Plug Part Number: 1143ACABLE-15M # Name Description MFG Manufacturer P/N Belcom P/N QTY 1. AC connector Plug female 3P+PE Cable OD = 10 to 12mm Binder *AC cable Cable AC 4x2.5mm OD=11.5mm LAPP GROUP OLFLEX ROBUST G or Equivalent 3. End terminal Cord end terminal D=2.6mm L=7mm KST (K.S.Terminals) EN2507 OR Equivalent Sealing tape Sealing tape Le Mark RT24BLACK Meter * Not supplied Assembly: 1. Strip 40 mm from both sides of the AC Cable outer sleeve. 2. Strip 8 mm of insulation from every wire s end. 3. Using a proper crimping tool, crimp the cord end terminals (supplied) on the wire stripped tips (four on each cable side). 4. Insert the cable through the connector record parts (1a, 1b, 1c, 1d). 5. At the connector side, insert each wire end terminal to the proper connector contact according to the schematics below. 6. Tight all terminal screws. 7. Assemble the connector. Tight the cable sleeve (1a) and pressing screw (1d) in order to assure sealing. 8. After connecting to the BUC, Wrap the sealing tape around both the cable and the mating connector. I-1

18 BLC-10/20/25/40/50 User Manual Appendix I: AC Cable Assembly - Straight Plug CAUTION It is recommended to seal all the connectors on the BUC (i.e. the IF cable connector, the power supply and the M&C) using a sealing tape (such as LeMark PN RT24 or equivalent, see Figure 2-6). Schematics: (Cords color are valid for the recommended cable) I-2

Appendix J: Control Cable Assembly BLC-10/20/25/40/50 User Manual

Description MFG P/N Belcom P/N Qty/Length (m) 1.

Control cable Cable Control 18x0.5mm OD=11.

19 Appendix J: Control Cable Assembly BLC-10/20/25/40/50 User Manual Appendix J: Control Cable Assembly Part Number: 1006CCABLE Name Description MFG P/N Belcom P/N Qty/Length (m) 1. BUC control connector Plug Way Size 14 ( mm) 2. Control cable Cable Control 18x0.5mm OD=11.8 mm Amphenol 62IN-16J-14-15SW LAPP GROUP OLFLEX ROBUST or equivalent a 1b 1c 2 1d J-1

20 BLC-10/20/25/40/50 User Manual Appendix J: Control Cable Assembly 1. Strip 30 mm of both sides of the cable. 2. Strip 5 mm of all the wire ends. 3. Plate the wire ends with solder. 4. Insert the cable through the connector shell (1a, 1b). 5. Solder the wires to the connector. 6. Connector Assembly: seal by tightening the cable holder (1c). 7. Fasten the two Phillips screws (1d). CAUTION It is recommended to seal all the connectors on the BUC (i.e. the IF cable connector, the power supply and the M&C) using a sealing tape (such as LeMark PN RT24 or equivalent, see Figure 2-6). Schematics: (Cords color are valid for the recommended cable) To BUC Control Connector Status A 1 Over Temp (temp mute1) B 2 Temp (temp warning1) C 3 P.S. Status (hpa ps1) D 4 Reflected Power E 5 Fan Rotation Status F 6 Total Failure (total1) G 7 Temp Analog Out H 8 Mute 1 J 9 REF TH Status (buc1) K 10 Output Forward Power Ind. L 11 Output Reflected Power Ind. M 12 GND N 13 GND P 14 Yellow/Green Wire Numbering R 15 J-2

Appendix K: BLC-10/20/25 DC Cable Assembly BLC-10/20/25/40/50 User Manual Appendix K: BLC-10/20/25 DC Cable Assembly Part Number: 1006DCABLE-30M Description Vendor P/N Belcom P/N 1 Cable, DC, 4x1mm,

21 Appendix K: BLC-10/20/25 DC Cable Assembly BLC-10/20/25/40/50 User Manual Appendix K: BLC-10/20/25 DC Cable Assembly Part Number: 1006DCABLE-30M Description Vendor P/N Belcom P/N 1 Cable, DC, 4x1mm, OD=6.6, L=30 Belcom A1006DCABLE-30 2 Sealing tape Le Mark RT24BLAC K Connect the "+","RTN" and "GND" wire ends to the power supply, according to the schematics below. 2. Connect the cable plug to the mating DC power inlet of the BUC. 3. Wrap the sealing tape on the cable plug after connecting it to the BUC. Schematics: CAUTION It is recommended to seal all the connectors on the BUC (i.e. the IF cable connector, the power supply and the M&C) using a sealing tape (such as LeMark PN RT24 or equivalent, see Figure 2-6). K-1

23 Appendix L: BLC Technical Specifications BLC-10/20/25/40/50 User Manual Appendix L: BLC Technical Specifications Operating Frequency: see Table 1-1. Gain and Power Table L-1: Electrical Specifications Gain [db] (Nominal) Power 1dBcp] (minimum over operating conditions) BLC BLC BLC BLC BLC Gain Stability: Gain Variations over full band Gain variations over 36MHz Gain Variation over Temp (-40 to +55 C) Phase Noise: 100Hz Offset 1KHz Offset 10KHz Offset 100KHz Offset 1MHz Offset External Reference signal frequency Reference signal level requirement External Reference Phase Noise Requirements: 10Hz Offset 100Hz Offset 1KHz Offset 10KHz Offset ±2dB 1.5dB PTP 4dB -60 dbc/hz -70 dbc/hz -80 dbc/hz -90 dbc/hz -100 dbc/hz 10 MHz -10 to +10 dbm -110 dbc/hz max -120 dbc/hz max -130 dbc/hz max -140 dbc/hz max L-1

24 BLC-10/20/25/40/50 User Manual Appendix L: BLC Technical Specifications Spectral Purity Intermodulation distortion at 6dB Back off P1 db - 3dB Transmit Noise (In-band) BLC-10 BLC-20/25 BLC-40/50 Receive band noise -27 dbc max -20 dbm max -50 dbc max -90 dbm/hz max -84 dbm/hz max -81 dbm/hz max -163 dbm/hz max Input Impedance Input VSWR Output VSWR 50 2:1 max 2.5:1 max L-2

25 Appendix L: BLC Technical Specifications BLC-10/20/25/40/50 User Manual Table L-2: Interfaces RF Output Connector RF Input Connector Power Supply Connector (where applicable) CPR-137 Grooved N Type BLC-10/20/25-DC - Receptacle 3 pin male 13A sealed BLC-40/50-DC - Receptacle 4 pin male with PE BLC10/20/25/40/50-AC - Receptacle 3 pin male with PE M&C Connector (optional) Size 14, 15 contacts male M&C Interface functions (optional, see Appendix E): Input: Mute Control Output: Status Output RF Power monitoring Fan Rotation Indications (BLC-40/50 S/N 200 and up) General Fault RF Reflected Power Monitoring High Temperature Alarm Un-locked PLL Alarm Output Mismatch Alarm L-3

26 BLC-10/20/25/40/50 User Manual Appendix L: BLC Technical Specifications Table L-3: BUC - Mechanical Specifications BLC-10/20/25 DC Mechanical Specifications: Dimensions (W x L x H) 212 x 268 x 110 mm Weight 7.2 kg BLC-20/25/40/50 AC and BLC-40/50 DC Mechanical Specifications: Dimensions (W x L x H) 228 x 268 x 238 mm Weight (Kg) 12 kg Finish: White polyurethane paint Table L-4: Ambient Environmental Conditions Operating Temperature -40 to +55 C Storage Temperature -55 to +85 C Cooling System (integrated) (20/25/40/50W) Forced air Relative Humidity 100% Altitude 3000 m max Table L-5: Indicators L1 Indicator See Section 3.2 L2 Indicator See Section 3.2 Over Temperature Shutdown Missing 10MHz reference Table L-6: Protections +80 C (case temperature) Transmission mute L-4

27 Index BLC-10/20/25/40/50 User Manual Index A Appendix A - BLC-10/20/25 DC Models Packing List 1 Appendix B - AC Models Packing List 1 Appendix C - BLC-40/50 DC Packing List 1 Appendix D - DC Power Inserter Packing List 1 Appendix E - Control 1 Appendix F - Detectors Calibration Tables 1 Appendix G - BLC-40/50 DC Cable Assembly 1 Appendix H - AC Cable Assembly - L-Shape Plug 1 Appendix I - AC Cable Assembly - Straight Plug 1 Appendix J - Control Cable Assembly 1 Appendix K - BLC-10/20/25 DC Cable Assembly 1 Appendix L - BLC Technical Specifications 1 Available Models and Configurations 1-3 B BLC-10/20/25 DC 1-4 BLC-10/20/25 DC Installation 2-5 BLC-10/20/25/40/50 AC and BLC-40/50 DC 1-5 BLC-10/20/25/40/50 AC and BLC-40/50 DC Installation 2-6 BLC-10/20/25/40/50 AC and External DC Cable- Connection 2-9 BUC General Description BLC-10/20/25/40/50 AC and BLC-40/50 DC 1-5 BUC General Description 1-4 BLC-10/20/25 DC 1-4 BUC Indication Lights 3-2 BUC Overview 1-1 BUC Possible Failures and Causes 3-3 Problem - No Output Power 3-3 Problem / Suspicion - Low Output Power 3-5 Problem / Suspicion - No Output Power 3-5 BUC Powered by a DC Power Inserter via IFL Cable Connections 2-7 BUC Troubleshooting 3-2 BUC Indication Lights 3-2 C Corrective Maintenance - Fan Replacement 3-8 D DC Power Inserter 1-6 Overview 1-6 Physical Description 1-7 DC Power Inserter Indication Lights 3-6 DC Power Inserter Installation 2-7 DC Power Inserter Overview 1-6 DC Power Inserter Physical Description 1-7 DC Power Inserter Possible Failures and Causes 3-6 Problem - Low or Zero Output Current 3-7 Problem - Low Output Voltage 3-6, 3-7 Problem - No IF Output Power or Low IF Output Power from the Power Inserter 3-7 Problem - No Output Voltage 3-6 DC Power Inserter Troubleshooting DC Power Inserter Indication Lights 3-6 DC Power Inserter Possible Failures and Causes 3-6 E Equipment Damage or Loss 2-2 F Fan Replacement 3-8 Features and Advantages 1-2

28 BLC-10/20/25/40/50 User Manual Index H Handling 2-1 Equipment Damage or Loss 2-2 Receiving and Inspection 2-2 Return of Equipment 2-2 Storage 2-2 Transportation 2-1 Handling and Installation 2-1 Handling 2-1 Installation 2-4 Post Installation Checks and Operation 2-11 Unpacking 2-3 I Installation 2-4 BLC-10/20/25 DC Installation 2-5 BLC-10/20/25/40/50 AC and BLC-40/50 DC Installation 2-6 BLC-10/20/25/40/50 AC and External DC Cable- Connection 2-9 BUC Powered by a DC Power Inserter via IFL Cable Connections 2-7 DC Power Inserter Installation 2-7 Introduction 1-1 Available Models and Configurations 1-3 BUC General Description 1-4 BUC Overview 1-1 DC Power Inserter 1-6 Features and Advantages 1-2 System Overview 1-1 M Maintenance 3-1 BUC Possible Failures and Causes 3-3 P BUC Troubleshooting 3-2 Fan Replacement 3-8 Power Inserter Troubleshooting 3-6 Preventive/Scheduled Maintenance Activities 3-1 Post Installation Checks and Operation 2-11 Power Inserter Troubleshooting 3-6 Preventive/Scheduled Maintenance Activities 3-1 Problem - No Output Power 3-3 Internal Temperature Protection Activated 3-4 Missing IF Signal 3-5 Missing Power Supply 3-3 Missing, Low or Unstable 10 MHz Reference 3-4 Power Supply Low Voltage 3-4 Problem / Suspicion - Low Output Power 3-5 Problem / Suspicion - No Output Power 3-5 R Receiving and Inspection 2-2 Return of Equipment 2-2 S Storage 2-2 System Overview 1-1 T Transportation 2-1 U Unpacking 2-3 Instructions 2-3 Unpacking Instructions 2-3

Belcom Microwaves BLC 10/20/25. BLC 10/20/25 User's Manual. Manual P/N: MB1052, Revision 1.01

Belcom Microwaves BLC 10/20/25 BLC 10/20/25 User's Manual Manual P/N: MB1052, Revision 1.01 December 2009 Contacting Belcom The following information is provided for your use. Please feel free to contact