(2) 3/4 NPT Remote Mount Field punched/drilled into MCC cabinet for Direct Mount

Transcription

1 ata Sheet P/ Phase On/Off/Jog/Proportional ISO S_P Ver _00 The three phase P series quarter turn actuators have been designed for dependable performance in rugged industrial applications such as clean water and wastewater treatment, mining, process control, power and damper control. Proation ngineering has an extensive stock of electric actuators and can ship product very rapidly, worldwide. Several key features increase the reliability: otor ontrol enter with status lights, attached or some distance away, allows local or remote control utomatic Phase onitoring hecks for phase reversal, phase loss, and phase imbalance etects low or high voltage to protect the actuator from damage, such as during start-up utoalibration means less setup time (proportional only) ctuator Specifications P P Torque lb/nm 00 lbs/000nm 000 lbs/00nm Supply Voltage 0//0 0//0 0//0 0//0 0//0 0//0 0//0 0//0 ax Inrush urrent unning urrent otor Polyphase untime sec sec untime 0 sec 0 sec uty ycle On/Off/Jog: %, Proportional: anaged (% maximum) otor Starts 00 per hour Weight lbs/kg (add lbs/.kg for ) echanical onnections ISO nd mm lectrical ntry () / NPT emote ount ield punched/drilled into cabinet for irect ount lectrical Terminations nvironmental ating anual Override ontrol ctuator ase aterial otor Protection mbient Temperature Operating ange ll applications have ield connections of -ga and 0-ga inside otor ontrol enter. or emote mount applications: conductors -ga rated for 0vac, -conductor shielded signal cable, plus conductors 0-ga rated for incoming power are required between the and the ctuator. N, X (ctuator), is N standard or optionally X SS or. Handwheel On/Off/Jog Proportional luminum lloy, Powder coated 0 /0 Thermal * lass *Totally nclosed Non-Ventilated otors - to + -0 to + Page of P/ Series lso available in three phase without otor ontrol enter (X). Separate spec sheets are available for these configurations. Product Notes:. The Phase P Series can be ordered as an on/off (two position) model that can also be used in bump/jog applications.. It can also be ordered with a premium internal proportional control card that accepts a wide range of control signals, generates multiple feedback signals, and has look-ahead fault prevention.. P Series phase versions are equipped with a otor ontrol enter () which features a built in local control station (S), which allows local or remote control of the actuator and is equipped with status indicators.. The houses the phase monitor for utomatic phase monitoring. This checks for phase reversal, phase loss, phase imbalance, low voltage or high voltage specifically to protect the actuator from damage during start-up and operating service conditions.. equires rd and th auxiliary switch set (Option-X) to control indicators.

2 Wiring iagrams for P Series On/Off/Jog ontrol SP I efer to the proper IO for your actuator for the correct wiring diagram or visit abinet door as viewed from the ONT OS OS STOP U STOP OS OT O O s viewed s viewed OO ield ontrol evice may be relay contact, Switch or Triac type. 0% PHS % IS STTUS % UNN Pilot device 0 X. uxiliary SUST STTINS switches are 00 % 0 00 % O PHS ONITO rated 0 0 0vac X. O 0V OPTION. S 0 0 NOIN TI 0 Terminals - VOT are dry O type NOT HN orm STTINS. STT WHN POW IS PPI. % S TO TOUSHOOTIN TI UNVOT SHT INU WITH. 0. OVVOT 0% Terminals accept -ga solid/stranded wire. PW O O OT K U PU K PU K OS PW N Switch ard K PU U 0 SW SW UXII SWITH (STN) UXII SWITH (STN) SWITHS SHOWN WITH TUTO IN U POSITION NOT * O* * NOT OS* OS O* OS* * ONNTIONS OPTION 0 0 SW SW UXII SWITH (STN) UXII SWITH (STN) SW SW SW SW SW SW Switch Stack etail Use or: OS Neu ault Out* 0//0 IN IN N emote Ind om* emote Ind ry* Ø Ø Ø ield Wiring ield (by Wiring others) (by others) 0 *0//0 W shown P~ U U 0/0 V V Ø T 0 V OI (OS) OI () 0 Items within dotted line located inside cabinet U U 0Kohm 0W 0Kohm 0W U U N K U U N HT J J 0vac ontrol ON N K N Screw SW SW U J 0V/Ø Items within dotted line located inside actuator housing U 0vac ontrol ON S_P Ver _00 Wire sizing data is provided in the table to assist in the selection of the proper wire size for these actuators using various wire sizes over distance. Please make sure to reference the correct voltage and do not exceed the indicated length of the wire run for each model. Wire Sizing hart X distance between ctuator and Supply (feet) ctuator P P Voltage 0//0 0//0 0//0 0//0 0//0 0//0 0//0 0//0 mps Wire age Page of P/ Series

3 Wiring iagrams for P Series Proportional ontrol SP I efer to the proper IO for your actuator for the correct wiring diagram or visit abinet door as viewed from the ONT OS PW OS STOP O O OT VIO VIO U K STOP OS OT O O s viewed s viewed K U N K N OS PW OO Switch ard K PU U 0% % IS % UNN % % NOIN VOT % UNVOT Pilot device 0 X. uxiliary switches are rated 0vac X. Terminals - are dry type orm. Terminals accept -ga solid/stranded wire. STTUS PHS S TI STT 0 S TI 0. OVVOT 0% 0 SW SW SUST STTINS O PHS ONITO O 0V OPTION. O NOT HN STTINS WHN POW IS PPI. TO TOUSHOOTIN SHT INU WITH. UXII SWITH (STN) UXII SWITH (STN) SWITHS SHOWN WITH TUTO IN U POSITION S_P Ver _00 0//0 IN IN NOT * O* * NOT OS* OS O* OS* * ONNTIONS OPTION N Signal O Signal IN+ Signal OUT+ Neu ault Out* emote Ind om* emote Ind ry* Ø Ø Ø 0 ield Wiring (by others) ield Wiring Use or: (by others) *0//0 W shown P~-0//0 PN- S T U V K 0 U U 0/0 V V Ø T 0 V Items within dotted line located inside cabinet Page of OI (OS) OI () Proation Premium ontroller: The Premium controller offers a full array of features - such as various control and feedback signals, alphanumeric readout, several fault indicators for operational diagnostics, extensive data logging that provides full proportional control for all industrial applications. odus communications are also an option on this controller. ontrol Signal Inputs (selectable using program menu): 0-0vdc, -vdc, -0vdc, -0m actory set with common isolated from ground. round reference is possible. 0 eedback Signal Output (an be different than input): 0-0vdc, -vdc, -0vdc, -0m ax oad: 0 ohms U U 0Kohm 0W 0Kohm 0W U -0m 0 ohms 0µ P/ Series 0 U N K U U N U SW SW TO J ONNTO ON O J UXII SWITH (STN) UXII SWITH (STN) K SW SW J HT J U SW SW SW SW SW SW U OUT Switch Stack etail 0V/Ø N Screw Items within dotted line located inside actuator housing Proportional ontrol ull Proportional ontrol eaturing: utocalibration Programmable High resolution larm Outputs ata logging Simple User Interface ield Selection riendly Thermal anagement Signal Input Impedance Sensitivity 0-0vdc 0k ohms 0mV -vdc 0k ohms 0mV -0vdc 0k ohms 0mV K N IN O 0vac ontrol ON

4 P/ Series imensional ata V ngineering hange Notice hange ate escription Name mm.0 in New ocument KH 0..0 dded tolerance on drive coupling data KH Pushed output diameter dimension to three decimal places, added keyway dimension KH Updated drawing with better assembly and standardized KH dded Isometric view of rive oupling and "epth" tag for clarity KH mm. in P Series xploded View (Typical) asily distinguishable yellow/red position indicator 0 mm. in mm. in mm. in mm 0. in mm. in luminum asting X Protection mm 0.0 in 0 mm.0 in mm. in mm. in mm. in mm 0. in mm. in dd mm [0."] for cover removal mm. in odular ontrol ards Heavy uty rive otor asily accessible switch & cam stacks N over Seal mm. in rive oupling abrication ata.0 mm.0 in mm. in K.00 mm 0.00 mm. in. in () 0x. 0mm." 0 mm. in mm. in H mm. in Keyway Worm rive mm mm -.. in in epth 0.00 rawn y reated: Part No. KHInstallation //0 Notes: ISO lange Proation ngineering, Inc. hecked y ast hecked: //0 wg. Name KH. These actuators This are ocument to is the be property mounted of Proation ngineering, ON between a P_ horizontal with and imata.idw upright position. aterial inish Inc. istribution of this document without the written consent of the owner is Strictly forbidden. ev. ailure to comply will incur a liability for amages. P~P with im ata imensional Tolerances (Unless Otherwise Noted): Promation ngineering Inc. X.X ±. conduit [X.XX ±.0] condensate from entering the actuator. imensional ata for P~P ctuators with light Path rive Phone: -- X.XX ±. [X.XXX ±.00] rooksville, l 0 ax: -- TON TUS IN mm NO S Sheet Number: Page of mm.0 in P/ Series luminum asting X Protection. When installing conduit, use proper techniques for entry into the actuator. Use drip loops to prevent. oth NPT conduit ports UST use proper equipment to protect the N x integrity of the housing.. The anti-condensate heater is to be used in applications.. o not install or store the actuator outdoors or in humid environments without power to the heater.. Use proper wire size to prevent actuator failure (see wire sizing chart).. echanical travel stops exist to prevent over-rotation for manual override only. They are not intended to stop motor driven rotation.. o not parallel wire multiple on/off actuators together without utilizing isolation relays! If this is your intention, please contact Proation ngineering for a multiple actuator parallel wiring diagram. Switch sequencing data is provided in the table below to show the change-of-state points during the rotation of the actuator from to OS and back again. The red bar indicates when that terminal makes with its respective common. SW and SW are set at the factory and should NOT be changed. The INU auxiliary switches SW & SW are for terminals thru and those setpoints may be modified if need be. When so optioned, SW & SW auxiliary switches are initially set to function the same as auxiliary switches SW & SW. Switch ogic ap and Switch/am rrangement Terminal I# 0 W - 0 W 0 Not Open Open ommon Open Not losed losed ommon losed picyclic earing SW W UX }(actory Set - dj) } SW W UX (actory Set - dj) Used by ontroller } On/Off Switch/am arrangement shown lutchless Override Handwheel S_P Ver _00

5 otor ontrol enter eatures: ON when actuator is fully W xterior View ON when actuator is NIN ON when actuator is fully W ain Phase Power lock onnections Interior View eversing otor Starters Positioning control switch when is in O mode ccess atch (quarter-turn) Phase onitor ctuator OTO connections ON when POW is present N ode switch is not O ode Switch (selects between O and OT operation) ield onnection terminals Proportional Signal able WNIN! The ode switch does NOT function as a service disconnect! Power is still present inside the enclosure when the mode switch is O. ctuator interconnect terminals 0v control transformer S_P Ver _00 Phase onitor alibration: Universal voltage range of 0-0V provides the flexibility to cover a variety of applications with one unit Protects against phase loss, phase reversal, phase unbalance, undervoltage and overvoltage Variety of user-selectable and adjustable settings for the ultimate in three-phase protection utomatic or anual eset ulti-olor indicates normal condition and defines fault to simplify troubleshooting ompact plug-in case utilizing industry-standard pin octal socket 0 SPT output contacts t the heart of the Proation ngineering otor ontrol enter () is the Phase monitor relay. Unlike other three-phase industrial actuators, the Proation Phase monitor utilizes a microprocessor-based design to provide protection against phase loss, phase reversal, phase unbalance, undervoltage and overvoltage as well as unbalanced voltages or single phasing regardless of any regenerative voltages. The relay is energized when the phase sequence and all voltages are correct. ny one of five fault conditions will de-energize the relay. s standard, re-energization is automatic upon correction of the fault condition. The Phase monitor not only protects the motor, but the process as well. Phase disruption can cause the motor to run in an unintended direction. multi-color indicates normal condition and also provides specific fault indication to simplify troubleshooting. The Phase monitor offers a variety of user-adjustable settings. The percent phase unbalance is adjustable from -0%, and also has a isable setting for those applications where poor voltage conditions could cause nuisance tripping. The undervoltage drop-out can be set at 0-% of operating voltage (overvoltage setting is fixed at 0% of nominal). The adjustable time delay drop-out on undervoltage (0.-0 seconds) eliminates nuisance tripping caused by momentary voltage fluctuations. There is also an adjustable time delay (-00 seconds) on both power up and restart after a fault has been cleared. Page of P/ Series utomatic Phase Protection

6 VI OPTIONS (actory Installed) Premium Proportional ontroller Option. onverts position to proportional control. echanical Torque Switch ssembly IP Protection (actuator only), tested to 0.kgf/cm for hours. P~P only. k ohm position feedback potentiometer. k ohm position feedback potentiometer. 0k ohm position feedback potentiometer. -0m feedback generator for On/Off/Jog actuators. Integral Thermostat for Heater ontrol - turns on at, turns off at 0. old weather auxiliary heater option. Thermostatically controlled, On, Off at 0, auto reset, hermetically sealed. W Internal Heater, power consumption. hain wheel override for applications where an actuator is mounted some distance from the floor. (Use with S). poxy coating (actuator) for increased environmental protection. Nylon coating (actuator) for increased environmental protection. Stainless Steel (actuator) enclosure. P~P Only. iberglass () enclosure for N X protection. Stainless Steel () enclosure for N X protection. N X iberglass enclosure Proation Product ine N X Stainless Steel enclosure P Series inear rive Up to 00lbs down/up force and up to 00mm ( ) stem travel or globe valves, gate valves and linear travel devices. With override handwheel. vailable with On/Off/Jog or Proportional control for vac, vdc, 0vac & 0vac supplies. P Series Non-Spring eturn lbs through 0,000 lbs. Quarter-Turn, with anual Override vailable with On/Off/Jog or Proportional control. or vac/ dc, vac/dc, 0vac, 0vac, 0v/ phase, 0v/ phase & 0v/phase supplies. P~P Series Spring eturn lbs through 00 lbs. Quarter-Turn, both with and w/o manual override handwheel. Spring either W or W. vailable with On/Off control for vac/dc and On/Off or Proportional control for 0vac & 0vac supplies. Stepdown for phase available. PU attery ack-up Systems Provides power sufficient to drive P Series actuators to fi eld-selectable fail-safe positions. or P Series & P Series actuators in On/Off and Proportional control modes. vailable for /0/0vac actuators. 0vac/0 vac supply. S_P Ver _00 Proation ngineering follows a policy of continual product updates and enhancements. Our website is the best place to obtain the latest product documentation, including the wiring diagrams for these controllers. Visit us at or use the Q code below to link to the site. light Path rive rooksville, 0 Phone () - ax () - sales@promationei.com Page of P/ Series Use your smart phone barcode scanner app here.