MODEL EPM-96 EPM-96F. ph 0 to ph14: Resolution 0.01pH 0 to 100 :Resolution temp. 1 (Selection display)

Transcription

1 10. Maesuring Instruments MODEL: EPM -96, EPM-96F MODEL EPM-96 EPM-96F ph 0 to ph14: Resolution 0.01pH 0 to 100 :Resolution temp. 1 (Selection display) (in equivalent input) Less than ±0.05pH 4 ma to 20 ma DC Input / Output isolated type Maximum load resistance: 900Ω range: Freely selectable within the measurement range 2 point (A1 A2) 4 point (A1 A2 A3 A4) Relay contact: SPDT(1c) 240 V AC, 3 A and 30 V DC, 3 A (resistance load) Contact Selectable from upper / lower limit operation (ON / OFF control) Select from "Abnormal warning" or "It is maintaining it." Selectable from upper / lower limit operation (ON / OFF control, Timesharing proportinal control) Select from "Abnormal warning" or "It is maintaining it." Contact input - 1 point (External input for holding) Calibration Automatic proofreading: 2 point Automatic potential stability judgment standardized solution ph2,ph4,ph9,ph10(jis) and ph7(jis) combination Manual proofreading: Differences more than arbitrary 2pH Temperature: 1point hold feature Select from "Previous value hold" or "Optional value hold" or "Continuous" However, only the previous value hold is available in the mainttenance mode. Self-diagnosis The proofreading is defective. The incompetent potential is abnormal. Electrode diagnosis Temperature sensor short-circuit. Outside measurement range The converter is abnormal. Control operation - Timesharing proportinal control Range of bound pair setting: 0.00pH to ph Proportional band: 0.01pH to 4.00 ph Cycle: 5~300 sec. Control shift : Shift amount 0% to 50% at cycle Automatic changeability of cycle: The cycle extends automatically according to deflection when entering the range (F zone) with deflection. F zone: 1% to 100% of proportional band The maximum extension time at cycle: 0 sec. to 300 sec. Amount of the maximum control: 50% to 100%(It operates regardless of the proportional band. ) ELEPON E.C.A.P. Corporation 10 Measuring Instruments 1

2 Temperature amends element 500Ω(25 ), 6.8kΩ(25 ), 1kΩ(0 ), 10kΩ(25 ), 350Ω(25 ), There is no amends. Selectable from the above Ambient environment Temperature: -5 to 45 Relative humidity: 20% to 85% (without dew condensation) Storage ambient -25 to 65 Rated voltage 100 V to 240 V AC, 50/60 Hz, 10VA (max.) Rated voltage 100 V to 240 V AC, 50/60 Hz, 15VA (max.) Indoor-use panel installation type Panel case: ABS Terminal: PBT Panel: Dust and water proof structure Protective structure Conforming standards Panel:IP65(IEC60529, JIS C0920) Rear case: IP20 Terminal: IP00 Class II equipment: IEC Pollution level 2: IEC CE Marking FCC Rule 96mm (W) 96mm(H) 115mm(D) Case depth: approx. 105 mm (when panel-mounted) 500 g 550 g ELEPON E.C.A.P. Corporation 10 Measuring Instruments 2

3 10-2. MODEL: EOM - 96 MODEL EOM-96 ±2,000mV: Resolution 1mV (in equivalent input) Contact Calibration hold feature Self-diagnosis Ambient environment Less than ±5mV 4 ma to 20 ma DC Input / Output isolated type Maximum load resistance: 900Ω range: Freely selectable within the measurement range 2 point (A1 A2) Storage ambient -25 to 65 Protective structure Conforming standards Relay contact: SPDT(1c) 240 V AC, 3 A and 30 V DC, 3 A (resistance load) Selectable from upper / lower limit operation (ON / OFF control) Select from "Abnormal warning" or "It is maintaining it." Sensitivity revision adjust: ±200mV span variable range: 50.0~150.0% Select from "Previous value hold" or "Optional value hold" or "Continuous" However, only the previous value hold is available in the mainttenance mode. Outside measurement range The converter is abnormal. -5 to 45 Relative humidity: 20% to 85% (without dew condensation) Rated voltage 100 V to 240 V AC, 50/60 Hz, 10VA (max.) Indoor-use panel installation type Panel case: ABS Terminal: PBT Panel: Dust and water proof structure Panel:IP65(IEC60529, JIS C0920) Rear case: IP20 Terminal: IP00 Class II equipment: IEC Pollution level 2: IEC CE Marking FCC Rule 96mm (W) 96mm(H) 115mm(D) Case depth: approx. 105 mm (when panel-mounted) 500g ELEPON E.C.A.P. Corporation 10 Measuring Instruments 3

4 10-3. MODEL: ERM - 96 MODEL ERM-96 Method for measurement: galvanic cell 0~2mg/L: Resolution 0.01mg/L Selectable from the indication of decimal one column or two columns (in equivalent input) Less than ±5mV 4 ma to 20 ma DC Input / Output isolated type Maximum load resistance: 900Ω range: Freely selectable within the measurement range Contact 2 point(a1 A2) Relay contact: SPDT(1c) 240 V AC, 3 A and 30 V DC, 3 A (resistance load) Selectable from upper / lower limit operation (ON / OFF control) Select from "Abnormal warning" or "It is maintaining it." Calibration hold feature Zero Quantity Calibration Span Calibration(Comparison proofreading with DPD tester) Select from "Previous value hold" or "Optional value hold" or "Continuous" However, only the previous value hold is available in the mainttenance mode. Self-diagnosis Ambient environment The proofreading is defective. Outside measurement range The converter is abnormal. Temperature: -5 to 45 Relative humidity: 20% to 85% (without dew condensation) Storage ambient -25 to 65 Rated voltage 100 V to 240 V AC, 50/60 Hz, 10VA (max.) Indoor-use panel installation type Panel case: ABS Terminal: PBT Panel: Dust and water proof structure Protective structure Conforming standards Panel:IP65(IEC60529, JIS C0920) Rear case: IP20 Terminal: IP00 Class II equipment: IEC Pollution level 2: IEC CE Marking FCC Rule 96mm (W) 96mm(H) 115mm(D) Case depth: approx. 105 mm (when panel-mounted) 500g ELEPON E.C.A.P. Corporation 10 Measuring Instruments 4

5 10-4. MODEL: EPC-100AC (in equivalent input) Range EPC-100AC ph: ph 0 to ph 14: Resolution 0.01pH ORP: ±2,000mV: Resolution 1mV ph: Less than ±0.05pH ORP: Less than ±5mV 4 ma to 20 ma DC: input / isolated type Maximum load resistance: 500Ω Straightness: 0.5% ph: ph 0 to ph 14, ph 0 to ph 10, ph 0 to ph 8, ph 2 to ph 12, ph 3 to ph 11, ph 4 to ph 14, ph 4 to ph 10, ph 6 to ph 14 ORP: ±2,000mV ±1,400mV ±1,000mV ±700mV The change chooses it with the DIG switch of the interior panel. Adjustment Control operation Calibration Contact Capacity Operation Set Range Control range hold feature The hold point of contact input that I am washing The 1c point of contact. 2CH independence 250 V AC. 3 A max. (Resistance load) Selectable from upper / lower limit operation (ON / OFF control) The change chooses it with the DIP switch of the interior panel ph: ph 0.00 to ph ORP: 0 mv to ±2,000 mv ph: ph 0.1 to ph 4.0 (ph ± 0.1 to ph ±2.0) ORP: 1mv to 999 mv (±1mv to ±499 mv) Automatic proofreading: 2 point Automatic potential stability judgment standardized solution ph 4, ph 7, (JIS) and ph 7, ph 9(JIS) Combination Manual proofreading: Differences more than arbitrary 2pH "Previous value hold","optional value hold","continuous" Selectable from the above The change chooses it with the DIP switch of the interior panel. 1a radio pressure welding point input. (It is transmission hold in point of contact ON) Measurements shift : ph: ph±2.00, ORP: ±200mV Time constant input filter reshuffling : "No time constant", "Time constant approximately 7 secon Error massage a: Error of the proofreading (Asymmetric electric potential, Sensitivity, Reply speed abnormal, Standard solution abnormal) b: Electrode diagnosis error (temperature sensor short circuit, Temperature sensor disconnection) c: Error out of the measurement range. (Full scale over, Full scale under) Ambient environment Temperature: -5 to 50 Relative humidity: Less than 85%RH Rated voltage 100 V to 115 V AC, 50/60 Hz, 7VA or 200 V to 240 V AC, 50/60Hz 7VA (It depends on appointment) Outdoor setting type: JIS CO920 Protection class 3 (rain proof type) Installation method Pole of 50A or Wall surface installation Case Polycarbonate (A resin color: White gray) Hood SPCC(color of the painting: DIC G262 equivalency) Fitting SUS mm(W) 186mm(H) 229mm(D) Do not include a fitting and a projection part 3kg ELEPON E.C.A.P. Corporation 10 Measuring Instruments 5

6 10-5. EPR Series MODEL ph recorder ORP recorder EPR-1S EPR-6S EPR-420S EPR-H200 (Hybrid type) 0 ph to 14 ph ±2,000 mv General precision ±1% (For a full scale) ±0.05% ±10 mv Input signal ph electrode 4 ma to 20 ma DC ph electrode Metal electrode Temperature compensation 0 to 100 Automatic or fixed resistance 500 Ω - 0 to Method Record width Electronic automatic equilibrium type 100mm Glass electrode-type mensuration Metal electrode-type mensuration Instructions speed Less than 5 second. (F S) Less than 3 second. (F S) Record method Speed of the chart felt-tip pen 10 mm/h, 20 mm/h, 40 mm/h (3 steps of gear change) Analog-style record: felt-tip pen Degital-style record: One color of ink ribbon wire dot method. Choose it among 41 kinds Warning 1upper limit circuit and 1 lower limit circuit - - 1upper limit circuit and 1 lower limit circuit "1a" 1 abnormal warning circuit "1a" AC 100V 50/60Hz AC 85~264V 50/60Hz Consumption electricity About 7VA 2kg About 35VA ELEPON E.C.A.P. Corporation 10 Measuring Instruments 6