Omega D2V Operating Notes
|
|
- Judith Nelson
- 6 years ago
- Views:
Transcription
1 Omega D2V Operating Notes David Elden 1 Introduction Changing The Lens Adjusting the Condenser Contrast Filters Inserting the Negative Adjusting Magnification Adjusting Focus Making the Exposure Replacing the Lamp... 5 Omega D2V Operating Notes 1
2 1 Introduction The Omega D2V enlarger is a B&W enlarger equipped with lenses and negative carriers for the following film formats: Format Lens Condenser Position Max. Magnification Ratio Min. Magnification Ratio 35mm 50mm x 5.25x 6x6cm 75mm x 2x 4x5in 135mm x 1.5x The lenses are mounted on lens-mounts for easy interchangeability. The condenser is adjustable by moving an auxiliary lens to various positions within the condenser housing. 2 Changing The Lens When not in use please leave the 135mm lens/lens-mount in place, the other lens/ lensmount assemblies should be stored in the plastic boxes in the drawer below the enlarger (the 135mm lens is in a lens-mount too tall to fit in the below bench storage). The lens-mounts have circular flanges with two flats. To remove a lens-mount loosen the two knurled screws on the underside of the lens stage then support the lens-mount while turning a quarter turn. Then lower the lensmount and store properly. To install a lens-mount reverse the procedure making sure the knurled screws are retightened (do not over-tighten). Lensmount screw Omega D2V Operating Notes 2
3 3 Adjusting the Condenser The auxiliary lens position in the condenser must match the lens being used; the appropriate positions are shown in the table above and on the inside of the housing trapdoor. To re-position the auxiliary lens open the trapdoor and carefully slide the lens out then replace in the desired position. Handle the lens with care to prevent it getting scratched or marked with fingerprints, with this design of enlarger such damage may show up on the print. Auxiliary lens part way into position 1 4 Contrast Filters Contrast filters for use with variable contrast paper are laid on top of the auxiliary lens wherever it is positioned. Contrast filter on top of auxiliary lens Omega D2V Operating Notes 3
4 5 Inserting the Negative The negative holders are a two-piece design; the negative is sandwiched between the two halves. The carriers have two alignment notches at the rear. Alignment notch The film stage is opened using the lifting lever on the left hand side of the lamp-house. The negative carrier is inserted such that the two notches on the rear engage with the two pins at the rear of the film stage. Once the carrier is seated close the stage using the lifting lever. Lifting lever (shown with film stage in closed position) Move lifting lever to this stop to hold film stage open 6 Adjusting Magnification Loosen the lock then adjust the enlarger head height by turning the crank on the right hand side of the enlarger. Once the desired magnification is achieved tighten the lock (do not over-tighten). Height lock knob Omega D2V Operating Notes 4
5 7 Adjusting Focus The focus is adjusted by moving the lens stage up or down using the focus knob on the right hand side of the enlarger. Focus knob 8 Making the Exposure An electronic timer that allows exposure times to be pre-set in 0.1s increments controls the lamp. For focusing and composing the image on the easel the lamp can be turned on continuously using the focus switch. Caution: Do not leave the lamp operating using the focus switch for long periods of time. Leaving the lamp operating for a long period of time will shorten the working life of the lamp and cause heat build up in the lamp house. 9 Replacing the Lamp Caution: Switch off the power to the enlarger before replacing the lamp. The lamp is located in the lamp-house at the top of the enlarger. To replace the lamp loosen the securing screws then lift off the lamp-house. The old lamp can then be unscrewed and a new one fitted. Replace the lamp-house and tighten the securing screws (do not over-tighten). The lamp type is GE PH211 (75W). Lamp-house securing screws Omega D2V Operating Notes 5
DIFFUSION MODULAR ENLARGER
DIFFUSION MODULAR ENLARGER MODEL fh-52 INSTRUCTION MANUAL 3684-OO05 Thank you for your having selected an LPL enlarger. Please read this manual carefully before using the enlarger, and keep it for future
More informationPRINTING SETUP with OMEGA ENLARGER
PRINTING SETUP with OMEGA ENLARGER Follow this procedure when beginning a work session in the Darkroom. Use this page as an actual checklist as you prepare to work. Get a key from the Monitor in the Cage
More informationO P E R A T I N G I N S T R U C T I O N S
E N L A R G E R MODEL 3C - 2B O P E R A T I N G I N S T R U C T I O N S Manufactured in India by (Rajkot, Gujarat) Description: Modern Model 3C-2B is a precision enlarger designed to take negatives up
More informationUSER MANUAL & PARTS LIST MODEL 40B S/N:
NUMBERALL STAMP & TOOL CO., INC. USER MANUAL & PARTS LIST MODEL 40B S/N: P.O. BOX 187, 1 HIGH ST. SANGERVILLE, ME 04479 www.numberall.com office@numberall.com TEL: 207-876-3541 FAX: 207-876-3566 MODEL
More informationDoor window. Front door window, assembly overview
64-50 Door window Front door window, assembly overview 1 - Window channel Pushed onto flange 2 - Door window Removing Page 64-52 Adjusting Page 64-53 3 - Door 4 - Outer window channel Pushed onto flange
More informationVanity Installation Instructions
Vanity Installation Instructions Segments of these instructions will relate to your vanity. Please read these instructions thoroughly and ensure the appropriate instructions are used during the installation
More informationSINCE 1922 P UBLICATION N O
SINCE 1922 GARED SPORTS MICRO-Z SET-UP INSTRUCTIONS VERY IMPORTANT! READ INSTRUCTIONS CAREFULLY AND FOLLOW STEP BY STEP SET-UP PROCEDURE P UBLICATION N O. 5 5 1 7 5 2 9 1 6 Recommended tools and accessories.
More informationOperating Manual. for CUTTING, PERFORATING, BENDING SLB120
Operating Manual for CUTTING, PERFORATING, BENDING SLB120 31040\B06eng 0896 0 Contents 1. Scope of delivery... 1 2. Technical specifications... 1 3. Applications... 1 4. Commissioning... 2 5. Cutting...
More informationSTEP 1 STEP 2 LEVELER KIT OPTION MOBILE CASTER KIT OPTION
B SERIES INDUSTRIAL BENCHES TOOLS REQUIRED FOR ASSEMBLY Socket set, Open end wrench set, Cordless drill with 3/8" socket bit (Magnetic recommended). BEFORE ASSEMBLY Read through the assembly instructions
More informationExponents Bench Cushion
Exponents Bench Cushion Power Drill #2 Phillips Bit Bit Holder Page 1 of 2 939500640 Rev A 1. Place cushion on top of the bench, so the black Coalesse tag is in the right rear corner of the bench. 2. From
More informationSTRINGING MACHINE OWNER'S MANUAL. Copyright 1998 GAMMA Sports - All Rights Reserved
6002 STRINGING MACHINE OWNER'S MANUAL Issue 3 - June 20, 1998 Copyright 1998 GAMMA Sports - All Rights Reserved 6002 OWNER'S MANUAL TABLE OF CONTENTS PAGE 1... WARRANTY PAGE 2... FEATURES PAGE 3... ASSEMBLY
More informationmodel tsa-sa48 Sliding Crosscut Table installation guide
model tsa-sa48 Sliding Crosscut Table installation guide A Note About Color Variations Among Anodized Aluminum Components Congratulations on the purchase of this SawStop Sliding Crosscut Table. We at SawStop
More information1 Removing The Screen Track, Screen and Screen Rollers Note: The screen remains in the track while the track is removed and/or installed.
Sliding Door Screen and Screen Track Replacement Service Instruction These instructions apply to: Architect Series 12/2004-Current Designer Series 3/2005-Current Tools Required: #2 Phillips head screwdriver
More informationCut-True 16M Manual Paper Cutter
Cut-True 16M Manual Paper Cutter 2/2013 OPERATOR MANUAL FIRST EDITION TABLE OF CONTENTS TOPIC PAGE Specifications 1 Safety Guidelines 1 Assembly 2 Overview 3 Description of Equipment Parts 3-4 Operation
More informationINSTALLATION GUIDE 2009-CURRENT HUMMER H3T PRODUCT CODE:
INSTALLATION GUIDE 2009-CURRENT HUMMER H3T PRODUCT CODE: 268 June 22, 2010 TOOLS NEEDED COMPONENTS INCLUDED P2 Tip 3/8" Drill Rubber Gasket(s) x 2 Bracket(s) x 2 1/2" Drill Bit Bulkhead Flange #2 Phillips
More informationOperating, Servicing, and Safety Manual Model " Foot Shear CAUTION: Read and Understand
Operating, Servicing, and Safety Manual Model 3000 52" Foot Shear CAUTION: Read and Understand These Operating, Servicing, and Safety Instructions, Before Using This Machine. SAFETY The purpose of the
More informationINSTALLATION MANUAL PBL-UMP
INSTALLATION MANUAL PBL-UMP Table of Contents Warning Statements... 4 Parts List... 5 Installation Tools... 5 Features... 7 Projector Preparation... 8 Bracket Installation... 10 Leveling the Mounting Bracket...
More informationBasic steps to time the Gammill quilting machine s rotary sewing hook
Basic steps to time the Gammill quilting machine s rotary sewing hook 1.) Turn the machine off and unplug it. 2.) With the needle bar in the raised position, remove the bobbin and bobbin case. 3.) Remove
More informationPrecision Pin-Registration Carrier Systems 4x5 and 8x10 systems
Precision Pin-Registration Carrier Systems 4x5 and 8x10 systems www.maskingkits.com Precision pin-registration carrier systems copyright Lynn Radeka. All rights reserved. Patent Pending. Precision Pin-Registration
More informationSliding Crosscut Table installation guide
Sliding Crosscut Table installation guide model tsa-sa48 A Note About Color Variations Among Anodized Aluminum Components Congratulations on the purchase of this SawStop Sliding Crosscut Table. We at SawStop
More informationEXPLODED VIEW AND PART CALL OUT ASSEMBLING THE METALUX DF SERIES FRAME KIT
EXPLODED VIEW AND PART CALL OUT CUTOUT DIMENSIONS ON PAGE 2 CEILING BRACING (BY OTHERS) SHEET ROCK METALUX DF SERIES FRAME KIT S282 (2'X2') FIXTURE SHOWN FIXTURE SIZE FRAME KIT PART # 2' X 2' DF-22W-U
More information1) Place the reactor stand on a sturdy bench with the bottom plate facing toward the front.
Assembly Instructions for ChemRxnHub Reactor Systems 1) Place the reactor stand on a sturdy bench with the bottom plate facing toward the front. Loosen knobs on the right and left using 2 hands of the
More informationCHEMINSTRUMENTS LABORATORY DRAWDOWN COATER LC-100 OPERATING INSTRUCTION
CHEMINSTRUMENTS LABORATORY DRAWDOWN COATER LC-100 OPERATING INSTRUCTION PRODUCT DESCRIPTION...2 UNPACKING...3 ASSEMBLY...4 Key Components...4 Set Up...5 OPERATION...5 MAINTANCE...7 WARRANTY...8 1 PRODUCT
More informationFootprint Mobile Assembly Instructions
Footprint Mobile Assembly Instructions 1998754 Revision -1 Complete Series Master Packet If you have any questions concerning these instructions, please call Kimball Office Customer Service. 20 Kimball
More informationSPECIFICATION OF COMPONENTS AND OPERATING KNOBS
SPECIFICATION OF COMPONENTS AND OPERATING KNOBS Serial number Description Page 1) 2) 3) 4) 5) 6) 7) 8) 9) 10) Base Projection board Hexagonal screws for fixing the column in the base Column Enlarger head
More informationNOTES ON PRINTING 08/06
NOTES ON PRINTING 08/06 1-Photographic materials are sensitive to most light sources. Never open your box of paper unless you are working under an appropriate yellow or red safelight. (Color photographic
More informationPORTA~TRACE. GAGNE, INC. 41 Commercial Dr. Johnson City, New York Phone: Fax: ASSEMBLY INSTRUCTIONS
PORTA~TRACE GAGNE, INC. 41 Commercial Dr. Johnson City, New York 13790 Phone: 1-607-729-3366 Fax: 1-607-729-7644 ASSEMBLY INSTRUCTIONS PORTA~TRACE MODEL 2436T LIGHT TABLE PORTA~TRACE MODEL 3648T LIGHT
More informationVastex Manual Press Registration System Assembly and Operations Manual
Vastex Manual Press Registration System Assembly and Operations Manual Contents Pg. # Introduction 2 Component Identification 2-3 Pallet Jig Assembly (Manual Rear Clamp) 4 Pallet Jig Assembly (Manual Side
More informationB235 Mobius Sconce Page 1 of 6
Mobius Sconce 28-9450 Page 1 of 6 CAUTION: FAILURE TO INSTALL THIS PRODUCT PROPERLY MAY RESULT IN PERSONAL INJURY OR PROPERTY DAMAGE. We recommend installation by a qualified individual trained in the
More informationOPTICAL BENCH - simple type
GENERAL DESCRIPTION: OPTICAL BENCH - simple type Cat: HL2240-001 Complete with Hodson Light Box. Cat: HL2241-001 Not including Hodson Light Box The IEC Optical Bench system is designed to be used with
More informationPet Door Panel Installation Manual
Pet Door Panel Installation Manual 400-558-1 1 4/3/03, 3:26 PM Components: Pet Door Panel Panel Latch Assembly Foam Weather-stripping Glass Sweep (4) Binding Posts (6) #6 x 1/2 Sheet Metal Screws (4) 8-32
More informationVanity Installation Instructions
Vanity Installation Instructions Segments of these instructions will relate to your vanity. Please read these instructions thoroughly and ensure the appropriate instructions are used during the installation
More informationItem # Thanks for shopping with Improvements!
Thanks for shopping with Improvements! Hampshire -Door Cabinet Item #5505 To order, call -800-64- West Chester, OH 45069 Made in China PR-6 If you have questions regarding this product, call -800-64- Mon.-Fri.
More informationSWIFT SERIES M2252DGL MICROSCOPE
SWIFT SERIES M2252DGL MICROSCOPE The M2252DGL Series is ideal for elementary to high school classrooms. Built to withstand student use, this series has locked-on eyepieces, objectives, illuminator housing
More informationMULTI-ACTIVITY PLAY TABLE
ASSEMBLY INSTRUCTIONS! WARNING: CHOKING HAZARD - Small parts. Not for children under 3 years.! CAUTION: Adult assembly required. C 2006 Melissa and Doug, Inc. All Rights Reserved www.melissaanddoug.com
More informationFor assembly see instructions in carton
88 5523 943 Kitchen Island IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occurring to the parts. We have
More informationPedestal Desk IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches
88 5549 181 Pedestal Desk IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damage occurring to the parts. We have taken
More informationColonial Classic Bar
88 5528 991 Colonial Classic Bar IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occuring to the wood parts.
More information1503 Follow Spot Yoke, Source Four LED
1503 Follow Spot Yoke, Source Four LED Rev 1.0 2016 City Theatrical, Inc. Getting Started with the City Theatrical Follow Spot Yoke for source four LED Congratulations on the purchase of your City Theatrical
More informationPantry IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or oth
88 5076 691 Pantry IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damages occurring to the parts. We have taken great
More informationArtisan Technology Group is your source for quality new and certified-used/pre-owned equipment
Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment FAST SHIPPING AND DELIVERY TENS OF THOUSANDS OF IN-STOCK ITEMS EQUIPMENT DEMOS HUNDREDS OF MANUFACTURERS SUPPORTED
More informationSabre Series 2 Inspired Design Precision Engineering
Sabre Series 2 Inspired Design Precision Engineering USER INSTRUCTIONS Thank you for choosing the Keencut Sabre Series 2. Every effort has been made to bring you a precision engineered product with the
More informationSTEINBERGER TRANSTREM (TYPE 2) TECHNICAL DOCUMENT
STEINBERGER TRANSTREM (TYPE 2) TECHNICAL DOCUMENT These instructions apply to newer style TransTrems only (non-threaded ball type or modified threaded ball type). For purposes of discussion, these TransTrems
More information3.2.3 Rear Door Window and Quarter Window Carrier Assembly
Tighten all bolts. Tighten bolts marked -1- and -2- in specified sequence. Tightening torque: 8 Nm Remaining bolts can be tightened in any sequence. Insert door window -3- through window recess without
More informationXM2 / XMU / XMU-S LENS ATTACHMENT KIT INSTALLATION GUIDE
XM2 / XMU / XMU-S LENS ATTACHMENT KIT INSTALLATION GUIDE for Paladin and Phoenix lenses The XM2 plate system attaches directly to most Epson, JVC and Sony home theater projectors regardless of ceiling
More informationInstructions for Making On-Line Reservations for Microscopes in NB11-204
Instructions for Making On-Line Reservations for Microscopes in NB11-204 1. Log into Mail using Mail.swmed.edu 2. Log in using your university id and password. 3. Click the Calendar Tab at the top right
More informationReplacing the Reciprocator on an SWF Multi-head.
Replacing the Reciprocator on an SWF Multi-head. Follow the instructions below to replace the reciprocator in the SWF multi-head machines. The tools required are found in the tool kit that came with the
More informationCustomer Notice: Congratulations again on your SawStop purchase, and thank you! -SawStop Tualatin, OR
Customer Notice: Congratulations on the purchase of this Sliding Crosscut Attachment. As the owner of a SawStop saw, you are familiar with our high standards for quality, fit and finish. Different from
More informationINSTALLATION MANUAL ELPMBUNI
INSTALLATION MANUAL ELPMBUNI Warning Statements WARNING: WARNING: WARNING: WARNING: PREMIER MOUNTS DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY PREMIER MOUNTS PRODUCT FOR PURPOSES OTHER THAN
More informationINSTALLATION MANUAL PBC-UMS
INSTALLATION MANUAL. PBC-UMS Premier Mounts 3130 E. Miraloma Avenue Anaheim, CA 92806 Phone: (800) 368-9700 Fax: (800) 832-4888 mounts@mounts.com www.mounts.com Rev. 01 PBL-110 Projector Mount Page 2 Installation
More informationV-Groover SIMPLEX INSTRUCTION AND OPERATION MANUAL M O DEL 703. For best results use only authentic Logan blades.
www.logangraphic.com SIMPLEX M O DEL 703 INSTRUCTION AND OPERATION MANUAL For best results use only authentic Logan blades CAUTION: BLADES EXTREMELY SHARP Use replacement blades #1258 Logan Graphic Products,
More informationJavelin Integra Inspired Design Precision Engineering
Javelin Integra Inspired Design Precision Engineering USER INSTRUCTIONS Thank you for choosing the Keencut Javelin Integra. Every effort has been made to bring you a precision engineered product with the
More information(Fig 1) Column to Base 1. Place Column (7) on the Base (13) and align holes in the Column with holes in the Base. 2. Attach using Bolt Washer and Spring Washer hole through the Column and into the Base.
More informationUser Manual. Digital Compound Binocular LED Microscope. MicroscopeNet.com
User Manual Digital Compound Binocular LED Microscope Model MD82ES10 MicroscopeNet.com Table of Contents i. Caution... 1 ii. Care and Maintenance... 2 1. Components Illustration... 3 2. Installation...
More informationHEIGHT ADJUSTABLE WORKBENCH
HEIGHT ADJUSTABLE WORKBENCH Model 91 ASSEMBLY and Operating Instructions Visit our website at: http://www.harborfreight.com Read this material before using this product. Failure to do so can result in
More informationInstruction Manual T Binocular Acromat Research Scope T Trinocular Acromat Research Scope
Research Scope Instruction Manual T-29031 Binocular Acromat Research Scope T-29041 Trinocular Acromat Research Scope T-29032 Binocular Semi-Plan Research Scope T-29042 Trinocular Semi-Plan Research Scope
More informationNo. 412, 414, 416 Operations Manual
No. 412, 414, 416 Operations Manual CARE: Occasional oiling of moving parts with machine oil will ease operation and extend the life of the brake. Occasionally check and tighten the lower beam bracket
More informationGE Monogram. Installation. Instructions. Microwave Oven. Under Cabinet Installation. and. JX827 Series Built-In Kit. Models.
GE Monogram Installation Instructions Under Cabinet Installation and JX827 Series Built-In Kit Models ZEM200 Series CAUTION WARNING Before you begin Read these instructions completely and carefully. IMPORTANT:
More informationDepending on the size you ordered you will have either 5 Foot sections which will build the 10 Foot frame or 6 Foot sections which will build the 12
XL Quilting Frame 1 Depending on the size you ordered you will have either 5 Foot sections which will build the 10 Foot frame or 6 Foot sections which will build the 12 Foot frame Printed 2 June 2014 Updated
More information1. Turn off or disconnect power to unit (machine). 2. Push IN the release bar on the quick change base plate. Locking latch will pivot downward.
Figure 1 Miniature Quick Change Applicators, of the end feed type, are designed to crimp end feed strip terminals to prestripped wires. Each applicator is set up to accept the strip form of certain specific
More informationElford - Entertainment Unit
Elford - Entertainment Unit Assembly Instructions- Please keep for further reference 245/8911 246/6934 Dimensions Width - 130cm Depth - 41cm Height - 53cm Important Please read these instructions fully
More informationBarnside Pantry IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratch
88 5516 653 Barnside Pantry IMPORTANT NOTE Carefully remove all the parts from the carton and put them individually on a soft cloth to prevent scratches or other damage occurring to the parts. We have
More informationBefore Assembling the Storage Wall
Chapter 1 Assembling the Lista Storage Wall Lista provides two types of standard Storage Walls: B251 and B255. The design, construction, assembly, and quality are identical for both types, however, B251
More informationAssembly Manual: Locus Desk. Caution: This is not your grandfather s office desk! Please read this manual thoroughly.
Assembly Manual: Locus Desk Caution: This is not your grandfather s office desk! Please read this manual thoroughly. Join the Upright Revolution Thank you for purchasing from Focal Upright and congratulations
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS MODEL RTA - 4985 Thanks for purchasing one of our products. Please read carefully the assembly instructions before the installation. Please save this manual for future reference.
More informationMODEL H9565 BALL BEARING GUIDE FOR G0513/G0514 INSTRUCTION SHEET
MODEL H9565 BALL BEARING GUIDE FOR G0513/G0514 INSTRUCTION SHEET Introduction The Model H9565 replaces the upper and lower Euro-style guides on your G0513 or G0514 Bandsaw. Inventory (Figure 1) A. Upper
More informationTV Floor Cart and Accessories
11. Adjustment INSTALLATION MANUAL Flo Cart and Accessies Loosen the knobs to adjust the display to the desired angle and tighten the knobs to secure. +5 /-12 + - + - 1200mm 1250mm 1300mm 1350mm 1400mm
More informationPilates IQ Reformer Set-Up
Pilates IQ Reformer Set-Up NOTE: Prior to assembly, check the parts and components you received against the following list. If you are missing any parts, please contact the Balanced Body customer service
More informationMove System Swivel Caster Installation ( )
Move System Swivel Caster Installation (002-10265-00) Caution Always disconnect power to chair before removing covers or performing any service procedures. Step 1: Remove Top Cover A) Position chair to
More informationTIP FOR GETTING STARTED
Tip for getting started TIP FOR GETTING STARTED Be careful not to drill into any electrical wires, ductwork, plumbing or other damagable components. If you have any questions on the locations of these
More informationAssembly & Installation Instructions
1 OF 6 Component Parts A Fixture Pipe (3) B Coupling (3) C Canopy Pipe (3) D Middle Canopy Can E Clutch (3) F Plastic Sleeve (3) G Side Canopy Can (2) H Set Screw (3) I Middle Crossbar J #10 Screws (4)
More informationFitted Furniture Installation and Aftercare Guide
Fitted Furniture Installation and Aftercare Guide Customer Service Contact Number 08008 778899 Important Information In the unlikely event that your product is damaged or faulty in any way, this must be
More informationOPERATION AND MAINTENANCE HANDBOOK D407270XA
OPERATION AND MAINTENANCE HANDBOOK D407270XA vers. 1.0 Thank you for choosing one of Silca s high quality key cutting machines. This machine has been designed, tested and produced in our factory using
More informationOPERATING INSTRUCTIONS MODULGRAV. Tel. +49 (0) Fax +49 (0) homepage:
OPERATING INSTRUCTIONS MODULGRAV Kolpingstraße -7 D-784 Singen / Htwl. Postfach 80 D-784 Singen / Htwl. Tel. +49 (0) 77 88-0 Fax +49 (0) 77 88 66 e-mail: info@elma-ultrasonic.com homepage: www.elma-ultrasonic.com
More informationThe wick in your heater needs replacing if, after repeated cleanings, any of the following conditions still exist:
WICK REPLACEMENT The wick in your heater needs replacing if, after repeated cleanings, any of the following conditions still exist: Slow to light, hard movement of the wick adjuster knob, kerosene odor
More informationF l a t S c r e e n A R M S I n s t a l l a t i o n
ITEM NUMBERS (1) #TOACAORG16 (2) #TOACAORG20 (3) #TOACATRP24 (4) #TOACATRP30 (5) #TOACATRPDS (6) #TOACATRPSS TOOLS REQUIRED (1) 3/8 Wrench (not provided) (2) Phillips head screwdriver (not provided) (1)
More informationDue to possible damage in shipping, the vertical stop assembly has been removed from this machine.
Due to possible damage in shipping, the vertical stop assembly has been removed from this machine. To assemble, insert the threaded rod through the shroud opening in the top of the machine. Start the four
More informationCeiling Tile Installations Part 1. Sheetrock Installations Part 2. WolfVision Support 2055 Sugarloaf Circle, Suite 125 Duluth, GA 30097
Ceiling Tile Installations Part 1 Sheetrock Installations Part 2 WolfVision Support 2055 Sugarloaf Circle, Suite 125 Duluth, GA 30097 (877) 873-WOLF support@wolfvision.us 0 EYE Series Mounting Kit Part
More informationBracket Assembly and Installation Manual
Bracket Assembly and Installation Manual Model POA-CHB-DWL2500 Contents Installation Precautions ------------------------- 1 Parts list -------------------------------------------- 2 Attach the Projector
More informationSetup. The Faraday Cage is available in two types of configurations. Cage for mounting to a full perimeter enclosure on series tables.
Faraday CageSetup, 2017 Setup The Faraday Cage is available in two types of configurations. Cage for mounting to a full perimeter enclosure on 63-500 series tables. Cage with a base plate for use on a
More informationDEVELOPMENT. The following developers are recommended: Ilford ID-2 Developer For Fine Grain Safety Positive Film.
DEVELOPMENT The following developers are recommended: Ilford ID-2 Developer For Fine Grain Safety Positive Film. Ilford ID-20 Developer For Bromide Paper. Both these developers may be obtained as packed
More informationJohn Deere 9570STS, 9650STS, 9660STS, and 9750STS Grain Tank Cross Auger Trough Liner EXOPLATE INSTRUCTION MANUAL
PLEASE READ THE ENTIRE INSTRUCTION SHEET BEFORE STARTING INSTALLATION. PLEASE REFER TO THE OPERATORS MANUAL FOR YOUR SPECIFIC COMBINE FOR PERTINENT SAFETY PRECAUTIONS THE TERMS. LEFT, RIGHT, FRONT, & REAR
More informationBig & Tall Executive Chair Assembly Instructions
Designed to be comfortable, and built to stay that way. Big & Tall Executive Chair Assembly Instructions 400 lbs Model 50106E PARTS A B C D Casters Quantity: 5 Star Base Quantity:1 Gas Lift Quantity: 1
More informationINSTALLATION INSTRUCTIONS DODGE RAM 2 & 4WD 1500 PART # P5058
INSTALLATION INSTRUCTIONS 2009-13 DODGE RAM 2 & 4WD 1500 PART # P5058 PARTS LIST: Qty Description Qty Description 1 Grille Guard 12 12-1.75mm Hex Nuts 2 Upper Frame Mounting s (for trucks without tow hooks
More informationGear Assembly Removal
Gear Assembly Removal 1 Remove the Top Cover, the Right Side Cover, the Fuser Assembly, and the Formatter Assembly. 2 Remove the Main Motor Assembly (see Figure 6-30). 3 Remove the (2) screws that hold
More informationTHE T-MAG II PRESS. Figure 6
THE T-MAG II PRESS The Lyman T-Mag Press features a powerful compound leverage with a unique position indexable turret and quick disconnect release system. This allows you to mount several die sets, precisely
More informationRim-Lock Door Set Installation Instructions
Rim-Lock Door Set Installation Instructions Let s get started Check Your Parts List Two Doorknobs with Set Screws B. Doorknob Spindle C. Rim Lock with Mounting Screws D. Keeper with Mounting Screws E.
More informationSLW 6 Channel Letter Brake. User Guide. Operation and Mounting Instructions
SLW 6 Channel Letter Brake User Guide Operation and Mounting Instructions Scope This document describes the operation and mounting instructions for the SLW 6" Channel Letter Brake. Please read all instructions
More informationSCHACHT STANDARD FLOOR LOOMTM
SCHACHT STANDARD FLOOR LOOMTM FL3109 FL3111 FL3113 FL3115 FL3121 FL3123 FL3125 FL3127 FL3310 FL3312 FL3314 FL3316 FL3322 FL3324 FL3326 FL3328 Assembly instructions LOW CASTLE LOOM IN MAPLE Find out more
More information8.0 RE-CALIBRATION OF SPACE
8.0 RE-CALIBRATION OF SPACE 101 ATTENTION: PLEASE READ BEFORE PROCEEDING. RE-CALIBRATION OF SPACE NO RE-ADJUSTMENT of space is required when changing from one code card to another. The space indicator
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS ITEM No. :Quilty/ 3 A helpful Assembly Video can be found on www.arrowcabinets.com in the Video Section under Quilty Incorrect Correct The turning direction of attaching The arrow
More informationHow to repair a broken potentiometer or pot
You pulled off the tone knob and it pulled out the stem piece with it; now it won't go back in. Watch this guide to see how to repair it. Written By: Adonis Urick Page 1 of 11 INTRODUCTION This shows how
More informationSwift M2250 Series Microscope Care and Use Manual
Swift M2250 Series Microscope Care and Use Manual SWIFT OPTICAL Enduring Quality and Technical Excellence. Swift Series M2250 Microscope The M2250 Series is ideal for elementary to high school classrooms.
More informationFull Overlay Door Panel Preparation and Installation Instructions for 2175, 2115, CLR2160 Models
Full Overlay Door Panel Preparation and Installation Instructions for 2175, 2115, CLR2160 Models www.u-lineservice.com Phone (414) 354-0300 FAX (414) 354-7905 Service & Parts Tech Lines Phone (800) 779-2547
More information1 of 2 3/3/2017 4:49 PM
1 of 2 3/3/2017 4:49 PM Front Door Window, Assembly Overview 1 - Window guide - Inserted on flange 2 - Door 3 - Inner window recess seal - Inserted on flange 4 - Bolt - 20 Nm 5 - Carrier assembly - Window
More informationOcular Lenses. Head. Arm. Objective Lenses. Slide Holder Stage. On / Off Switch. Condenser with Iris Diaphragm. Light Intensity Control
BIOLOGY 211: HUMAN ANATOMY & PHYSIOLOGY ********************************************************************************************************* USE OF THE LIGHT MICROSCOPE **********************************************************************************************************
More informationElecraft AF1 Audio Filter Enclosure
Elecraft AF1 Audio Filter Enclosure by W8FGU Elecraft AF1 Audio Filter Mounted in the AF1 Enclosure (Courtesy of Ron D Eau Claire). The AF1 enclosure is made of Lexan, a polycarbonate, which is very strong.
More informationCustom Bench Plane. Honing and Polishing the Blade. Blade Carrier
Custom Bench Plane U.S. Pat. No. 7,603,783 Your Veritas bench plane has been assembled with the component options you selected when you placed your order. Caution: Be aware that the blade is sharp; careless
More informationRULTRACT RETRACTOR CABLE REPLACEMENT INSTRUCTIONS. Rultract, Inc. is the ONLY authorized service center in the U.S.A.
RULTRACT RETRACTOR CABLE REPLACEMENT INSTRUCTIONS Rultract, Inc. is the ONLY authorized service center in the U.S.A. When your Rultract instrument needs repair or service, contact Rultract Inc. or Rultract
More informationINSTALLATION INSTRUCTIONS GRILLE GUARD RAM 1500 PART # 5058/5058-2
INSTALLATION INSTRUCTIONS GRILLE GUARD PART # 5058/5058-2 PARTS LIST: Qty Description Qty Description 1 Grille Guard 8 12-1.75mm x 35mm Hex Bolts 2 Upper Frame Mounting s (for trucks without tow hooks
More information