Subject: Models/Years Affected: Origination Date: Revision Date: N/A ADVISORY:
|
|
- Shonda Clark
- 6 years ago
- Views:
Transcription
1 Subject: Models/Years Affected: Origination Date: Revision Date: N/A UI Bulletin #127 Adding/deleting a Rear View Camera to a Box Delete (ZW9) or Chassis Cab Vehicle 2015i Chevrolet Silverado 2015i GMC Sierra w/zw9 Box Delete or Chassis Cab July 21, 2015 ADVISORY: Condition/Concern: Many Upfitters and customers have expressed a desire for the rear vision camera feature on a vehicle that has had an after-market body mounted to the vehicle. Beginning with the 2015i Full size pick-up trucks, the necessary wiring content was included on all vehicles with the Pick up box delete option (ZW9) to enable the installation of a camera. Repair/Recommendation: To add a rear vision camera to a vehicle not equipped, but built after September 2014 and having the RPO AVF, you ll need to use a service replacement camera assembly P/N Activation of the Rear Vision Feature will require a reprogramming by a GM Service Center of either the radio or the Human Machine Interface (HMI) module. On vehicle s equipped with the base radio option (RPO IO3) the radio will need to be reprogrammed, and on vehicles equipped with the IO4 or IO5 radio options, the HMI module will need to be reprogrammed. The radio/module reprogramming should completed PRIOR to mounting the camera, as the display will need to be activated in order to obtain a good rearview display coverage area. Dealers should contact TCSC to have a special Rear Vision Camera option (RWR) added to the vehicle s configuration index (VCI). RWR is a special option/calibration developed especially for adding a rear camera to a vehicle with a service body Once the VCI is updated, reprogram the appropriate module based on the radio option code. Bulletin #127 P a g e 1 July 21, 2015
2 The service replacement camera comes mounted is a bracket assembly (see figure 1) Service replacement Camera asm. Figure 1 The bracket needs to be removed and discarded. Remove the camera by removing the 2 screws as shown in figure 2, Remove these 2 screws to separate camera from bracket Figure 2 Discard this bracket asm. Once the bracket is removed, the camera becomes a stand-alone component (refer to figure 3). This camera can now be mounted in an upfitter provided bracket/housing for mounting to the vehicle. Bulletin #127 P a g e 2 July 21, 2015
3 Camera w/o bracket Figure 3 Mounting the Camera To determine the best mounting location use of following information is recommended in order to obtain the proper Field Of View (FOV) on the video display. The specifications for the Target Cylinders are provide in figure 4). Note the difference between A-E verses that of F&G. Targets A-E have an upper band that wraps around the top of the Cylinder and the F&G Targets have a vertical strip on the side. Targets F&G are place at the rear corners of the vehicle at the specified distances with the vertical stripes facing inward towards the center line of the vehicle. Bulletin #127 P a g e 3 July 21, 2015
4 Figure 4 The location of the target cylinders is identified in figure (TBD) and is based off the center line of the vehicle Targets F&G are place at the rear corners of the vehicle at the specified distances with the vertical stripes facing inward towards the center line of the vehicle. The remaining targets (A-E) are set at the distances noted. Bulletin #127 P a g e 4 July 21, 2015
5 Vertical Stripes Top banded stripes Figure 5 Bulletin #127 P a g e 5 July 21, 2015
6 Samples of Rear View Images Acceptable IO3 Radio Image balanced percentage of targets in view Figure 6 In this image, the horizontal FOV is wide enough to show adequate amount of targets 1.52m to each side, BUT lacks vertical FOV the distant (6m) targets are truncated. IO3 systems truncate 14 pixels from the top and bottom of the image (to fit the screen other infotainment systems stretch the image to fit the screen), making vertical FOV more challenging for IO3. Note: The IO3 image does not meet the image requirements for MVSS #111 and also does not support the guidelines as shown. Bulletin #127 P a g e 6 July 21, 2015
7 Bad Full RVC image (IO4/5) Note: Image lacks visible F&G targets and reduce height image on rear targets A-C OK Image Slight reduction of targets F&G Figure 6 Acceptable Image- slightly reduced view of targets F&G, but still shows the existence of an obstacle. Figure 7 Ideal Image high percentage of all Targets visible Bulletin #127 P a g e 7 July 21, 2015
8 Figure 8 For the IO4/5 ZW9 box delete vehicles the guidelines (shown above in Figure 8) will also be disabled as the vehicle centerline point of reference to camera mount location may not be accurate with respect to that of the image displayed and therefore the guideline overlay may not properly represent the vehicles travel path. Figure 9 REAR CAMERA RELOCATION/DELETE RELOCATION If performing a box removal equipped with a rearview camera use of the existing camera is applicable. However on a IO4/05 radio application the HMI module must be reprogrammed with the RWR option, replacing the UVC option code to remove the guidelines shown in Figure 8. DELETE If not planning to use the rear camera (if equipped) after a box removal the radio and/or HMI module should be reprogrammed without the UVC factory option to prevent the dash display from blanking out when backing the vehicle. Bulletin #127 P a g e 8 July 21, 2015
Subject: Upfitter Circuit. Models Affected: Chevrolet Silverado GMC Sierra Model Years: 2014 and Beyond Date: March 20, 2014 Revision Date: ADVISORY:
Subject: Upfitter Circuit Provisions Models Affected: Chevrolet Silverado GMC Sierra Model Years: 2014 and Beyond Date: March 20, 2014 Revision Date: January 12, 2018 ADVISORY: Condition/Concern: Upfitters
More informationBed Side Interchangeability - GM Short Stepside Beds
Bed Side Interchangeability - GM Short Stepside Beds We are frequently asked questions relating to fitting a bed or bed part from one year/model truck to a different year/model than that for which it was
More informationService Bulletin
Service Bulletin 09-094 Applies To: ALL October 30, 2010 Photos For Warranty Windshield Claims (Supersedes 09-094, dated February 23, 2010, to revise the information marked by the black bars) REVISION
More informationCRITICAL INFORMATION:
IMPORTANT ALERT: GM uses a very strong thread-locking compound on all body bolts. Use of an air assisted impact ratchet can cause damage to the threads on factory body mount bolts and the internal nut
More informationAX-AM-GM91. GM HDMI and Camera Interface 2013-up* *Visit AxxessInterfaces.com for up-to-date vehicle specific applications.
AX-AM-GM91 INSTALLATION INSTRUCTIONS GM HDMI and Camera Interface 2013-up* *Visit AxxessInterfaces.com for up-to-date vehicle specific applications. INTERFACE FEATURES Provides front and rear camera inputs
More informationASSEMBLY & INSTALLATION GUIDE
ASSEMBLY & INSTALLATION GUIDE APPLICATION GM Truck (Full-size Trucks) PART # 74805-00A (Silver) 74805-0A(Black) INSTALLATION TIME Hour SKILL LEVEL 2 3 4 = Easy TOOLS REQUIRED Phillips screw driver Torx
More informationCropping And Sizing Information
and General The procedures and techniques described herein are intended to provide a means of modifying digital images for use in projection situations. This includes images being displayed on a screen
More informationMETRIC BOlTS. Size Grade Torque 8mm ft/lbs. 10mm ft/lbs. 12mm ft/lbs. 14mm ft/lbs. 16mm ft/lbs.
8/16 HJ31005,Rev 7 BOlT TORQUE SPECIfICATIONS METRIC BOlTS STANDARD BOlTS Size Grade Torque 5/16 5 18 ft/lbs. 3/8 5 30 ft/lbs. 7/16 5 50 ft/lbs. 1/2 5 75 ft/lbs. 5/8 5 150 ft/lbs. 3/4 5 290 ft/lbs. Size
More informationWhite Paper Thermal: Detection, recognition, and identification
White Paper Thermal: Detection, recognition, and identification 250.426.8100 www.ascendentgroup.com info@ascendentgroup.com It is important to know just how far your camera can see under ideal conditions.
More informationInstallation Instructions TrekStep Side Mount
Installation Instructions TrekStep Side Mount Vehicle Application Chevrolet Silverado / GMC Sierra All Bed Sizes 1999 Current Part Number: 75400-15 www.bestop.com - We re here to help! Visit our web site
More informationINSTRUCTIONS FOR NFSC tour SPEED MEASURING SYSTEM
INSTRUCTIONS FOR NFSC tour SPEED MEASURING SYSTEM The NFSC tour Speed measuring system is designed specifically for accurately measuring the speed of tennis serves on the tennis court. The system is intended
More informationA WILSON ELECTRONICS BRAND DRIVE 4G-X OTR. Cellular Booster For Trucks. User Manual. NEED HELP? support.weboost.com
A WILSON ELECTRONICS BRAND DRIVE 4G-X OTR Cellular Booster For Trucks User Manual NEED HELP? support.weboost.com 866.294.1660 Index Package Contents 1 STEP 1: Select Mounting Location 2 STEP 2: Assemble
More informationSatellite Radio & Cellular Antenna Relocation Guidelines
Satellite Radio & Cellular Antenna Relocation Guidelines If an upfitter package s proximity to the satellite/cellular mobile media antenna causes interference with satellite and/or onboard cellular reception,
More informationAssembly & Installation Instructions FOR VEHICLE MOUNT KIT USING VEHICLE CENTER MEMBER
Assembly & Installation Instructions FOR VEHICLE MOUNT KIT 991002 USING VEHICLE CENTER MEMBER 9910092 TO FIT 99 - LATER Chevrolet 2500 Silverado 4x4 and 3500 Pickup 4x4 99 - LATER GM 2500 Sierra 4x4 and
More informationA Quick Guide to ios 12 s New Measure App
A Quick Guide to ios 12 s New Measure App Steve Sande For the past several years, Apple has been talking about AR augmented reality a lot. The company believes that augmented reality, which involves overlaying
More informationINSTALLATION MANUAL IOWA MOLD TOOLING CO., INC. BOX 189, GARNER, IA MANUAL PART NUMBER:
PARTS-1 Model 24562/28562 Crane INSTALLATION MANUAL IOWA MOLD TOOLING CO., INC. BOX 189, GARNER, IA 50438-0189 641-923-3711 MANUAL PART NUMBER: 99903701 Iowa Mold Tooling Co., Inc. is an Oshkosh Truck
More informationInstallation Instructions
CHEVY / GMC 20K Industry Standard Rail Custom Mounting Kit #2724 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order
More informationTest Report for: DBA DARE 2B DIFFERENT ENTERPRISES INC.
45000 Helm Street Suite 150 Plymouth Twp., MI 48170 Telephone: 734-582-2900 Facsimile: 734-582-2901 www.intertek.com Test Report for: DBA DARE 2B DIFFERENT ENTERPRISES INC. FIELD OF VIEW TEST One Rear
More informationCOLLISION REPAIR INFORMATION
COLLISION REPAIR INFORMATION FOR THE TOYOTA DEALER TITLE: 1991 MODEL BODY DIMENSIONS PAGE 1 of 26 SECTION: STRUCTURAL REPAIR BULLETIN #42 MODELS: 1991 MR2, PREVIA, LANDCRUISER, TERCEL DATE: MARCH 1991
More informationInstallation Instructions
CHEVY / GMC 16K Industry Standard Rail Custom Mounting Kit #2730 Gross Trailer Weight (Maximum)...16,000 lbs. Vertical Load Weight (Max. Pin Weight)...4,000 lbs. SYSTEM TOW CAPACITY Please note, in order
More informationOkay, that s enough talking. Let s get things started. Here s the photo I m going to be using in this tutorial: The original photo.
add visual interest with the rule of thirds In this Photoshop tutorial, we re going to look at how to add more visual interest to our photos by cropping them using a simple, tried and true design trick
More informationPickup Box Utility Rack Package Installation (Instruction ID: )
017 Chevrolet Colorado Pickup - WD (VIN S) Canyon, Colorado Accessory Installation Manual N America Document ID: 3966961 Pickup Box Utility Rack Package Installation (Instruction ID:3144879) Installation
More informationLF Series Assembly Instructions
LF Series Assembly Instructions 1998760 Revision A-10 Complete Series Master Packet 2010 Kimball International, Inc. T 800.482.1818 F 812.482.8300 Footprint Storage and Metal Filing Systems Assembly Instructions
More informationV00029KX READ ALL OF THE FOLLOWING INSTRUCTIONS BEFORE REMOVING CABINET FROM SKID
READ ALL OF THE FOLLOWING INSTRUCTIONS BEFORE REMOVING CABINET FROM SKID Net-Verse D-Type Cabinets Tool List 10mm Socket Wrench 122mm (48 ) Level 19mm Wrench 8mm Hex Drive T25 Torx driver Net-Verse D-Type
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Trans4mer Winch Mount For 2007-2010 Chevrolet Silverado HD and GMC Sierra HD Bracket Kit 90140 Your safety, and the safety of others, is very important. To help you make informed
More informationInstallation Instructions
CHEVY / GMC 24K Industry Standard Rail Heavy Duty Custom Mounting Kit #2226 Gross Trailer Weight (Maximum)...24,000 lbs. Vertical Load Weight (Max. Pin Weight)...6,000 lbs. SYSTEM TOW CAPACITY Please note,
More informationTOYOTA TACOMA LED BED LIGHTS Preparation
Preparation Part Number: PT948-35160 Kit Contents Item # Quantity Reqd. Description 1 1 Hardware Kit 2 1 Driver Side LED assembly 3 1 Passenger Side LED assembly 4 1 Main Wire Harness Hardware Bag Contents
More informationInstallation Instructions
CHEVY / GMC 20K Industry Standard Rail Custom Mounting Kit #2724 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order
More informationTonneau Cover Fitting Instructions
Tonneau Cover Fitting Instructions Package includes Nissan Navara Dual Cab NP300 / D23 With Factory Sports Bars April 2015 Current Part number: 10691 1 x Tonneau Cover 1 x Rope Track (1485mm Long) 2 x
More informationInstallation Instructions
FORD 20K Industry Standard Rail Custom Mounting Kit #2738 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order to determine
More informationFrameless Inline Door QCI5288
Frameless Inline Door QCI5288 QCI5288 Rev. 0 Page 1 Date Certified: 06/21/2016 Tools: To install your New Shower Enclosure, you may need the following: Pencil Drill Hack Saw Low Tack Tape 1/8 & 3/16 Drill
More informationR I T. Title: Wyko RST Plus. Semiconductor & Microsystems Fabrication Laboratory Revision: A Rev Date: 05/23/06 1 SCOPE 2 REFERENCE DOCUMENTS
Approved by: Process Engineer / / / / Equipment Engineer 1 SCOPE The purpose of this document is to detail the use of the Wyko RST Plus. All users are expected to have read and understood this document.
More informationHow to use detail drawings optimally
List of contents: 1. Introduction 2. PDF and DXF file content 3. Detail letter designation 4. Location of coordinate point(s) in the main generic drawing 5. Examples of detail drawings and how to use detail
More informationParts list. Model:10400
Manufacturing, Inc. Instruction sheet -- VTI Flat panel TV cart with cabinet Model number: 10400 Congratulations for having chosen this excellent VTI product. To assure your complete satisfaction, this
More informationOverlay Door Panel Preparation and Installation Instructions
DOOR PANEL INSTALLATION GUIDE Overlay Door Panel Preparation and Installation Instructions The Built-In Undercounter Leader Since 1962 U-LINE.COM Overlay Door Panel Door panel Preparation A Full overlay
More informationINSTALLATION INSTRUCTIONS Product No. MULTI-FIT PICK-UP
INSTALLATION INSTRUCTIONS Product No. You can take it with you. PLYMOUTH, MICH. MULTI-FIT PICK-UP 37034 SMALL PARTS PACKAGE 37424 WARNING: DO NOT LUBRICATE THREADS, BOLT FAILURE MAY OCCUR DUE TO OVER TIGHTENING.
More informationINSTALLATION INSTRUCTIONS
PACKAGE CONTENTS and PARTS LIST: INSTALLATION INSTRUCTIONS Additional copies of these instructions can also be found on our website at www.xtremegate.com in the section titled How to Install X-Treme Gate.
More informationBlum Space Corner User Guide.
Blum Space Corner User Guide. Introduction Overview The Blum Space Corner Package from Solid Setup adds the Blum Spacecorner extra drilling and shaped drawer box bottoms, to Cabinet Vision Solid. It positions
More information# in 1 Metal Worker Auxiliary Operating Instructions
340 Snyder Avenue, Berkeley Heights, NJ 07922 www.micromark.com MMTechService@micromark.com Tech Support: 908-464-1094, weekdays, 1pm to 5 pm ET #86556 3 in 1 Metal Worker Auxiliary Operating Instructions
More informationFull Size Pick Ups - GM Suburban/Yukon/Tahoe - GM Escalade - Cadillac Click on a link tab to jump to that page.
Publication, Duplication, or Retransmission Of This Document Not Expressly Authorized n Writing By The nstall Doctor s Prohibited. Protected By U.S. Copyright Laws. 1997,1998,1999,2000. Factory Radio Other
More informationMazda BT-50 With Factory Sports Bars 2012 Current Part number: Package includes
Tonneau Cover Fitting Instructions Mazda BT-50 With Factory Sports Bars 2012 Current Part number: 10019 Package includes 1 x Tonneau Cover 1 x Rope Track (1420mm Long) 2 x Bar Bracket (300474) 22 x 4 mm
More informationTriplex Instructions for Packing and Unpacking
2-8-8-2 Triplex Instructions for Packing and Unpacking It is recommended that you review all these instructions before removing the engine or tender from the poly foam container. www.mthtrains.com Table
More informationPontiac Grand Am SC/T Installation Instruction Sheet Aftermarket Front Fascia
Aftermarket Front Fascia be used correctly to install the secondary fascia to the existing fascia. 1 Fascia Front 5 Bolt M6-1.0x60 5 Washer 1/4x9/16 2 Bolt/Washer Assembly 1 Nut/Washer Assembly 1. Six
More informationINSTALLATION INSTRUCTIONS - NSF WALK-IN COOLER/FREEZER Wall-Mounted Shelving System - No Blocking
The components included with this shipment comprise a fully-adjustable, heavy-duty cantilever shelving system. Installed properly, they ll provide decades of superior value in your walk-in cooler or freezer.
More informationINSTALLATION INSTRUCTIONS
INSTLLTION INSTRUCTIONS GEN X STEP BRS PPLICTION: 2014-2015 Chevrolet Silverado & GMC Sierra 1500 Double Cab 2014-2015 Chevrolet Silverado & GMC Sierra 1500 Crew Cab 2015+ Chevrolet Silverado & GMC Sierra
More informationTinker Tuesday Project - Drinking Glasses
Tinker Tuesday Project - Drinking Glasses 1. Open CorelDRAW and create a new document. Near the top left corner of the screen, click File, and then click Import on the resulting menu. Select an image from
More informationShay Boiler - Mounts & Holes
Shay Boiler - Mounts & Holes Nelson Riedel Nelson@NelsonsLocomotive.com Initial: 11/14/03 Last Revised: 06/06/2004 The boiler was fabricated by a professional as discussed elsewhere. It was supplied with
More informationWireCrafters, LLC. General Information
WireCrafters, LLC. General Information 6208 Strawberry Lane 502/363-6691 www.wirecrafters.com Louisville, Kentucky 40214 502/361-3857 FAX 1-800-626-1816 The following General Installation Instructions
More informationTOYOTA TUNDRA TUBE STEPS Preparation
Preparation Part Number: PT95-34180 (D-Cab) PT95-3418 (C-Cab) Kit Contents 1 1 Left Hand Step Tube 1 Right Hand Step Tube 3 1 Hardware Kit Hardware Bag Contents 1 16 SEMS 8mm x 30mm Bolt 3 Additional Items
More informationTOYOTA TACOMA BED EXTENDER Preparation. Part Number: PT General Applicability All 2012 and newer Tacoma models
Preparation Part Number: PT392-35120 Kit Contents 1 1 Curved Tube Assembly - Right 2 1 Curved Tube Assembly - Left 3 3 Center Tube 4 1 Hardware Bag 5 1 Installation Instructions 6 1 Care Card Hardware
More informationAssembly Instructions
Selling Station Assembly Instructions View from above without top A B C D Rounded finished corners on A & D Square unfinished 3-sides on B & C Selling Station Components (2) 2' x 6' Side s Have a channel
More informationPT 335SCC Multi Operator Manual
PT 335SCC Multi Operator Manual 755 Griffith Court, Burlington, Ontario, Canada L7L 5R9 Tel:+(905) 633-7663 Fax:+(905) 637-4419 www.graphicwhizard.com 1 TABLE OF CONTENTS Important Information General
More informationAW-200GM APPLICATIONS GM MULTI KIT KIT FEATURES KIT COMPONENTS A B C TOOLS REQUIRED:
APPLICATIONS GM MULTI KIT 99-2001 AW-200GM KIT FEATURES DIN Head Unit w/ Equalizer Provision KIT COMPONENTS A) Radio Housing B) Spacer C) Equalizer Dummy Plate D) Shaft Masks A B C D TOOLS REQUIRED: Phillips
More informationFOLDING TONNEAU RACK. 1. Rack Rail Assembly
FOLDING TONNEAU RACK Package Contents (2) Load Bars (4) Load Bar End Caps (4) ¼-20 x 9/16 Narrow Shoulder Hex Head Screw (28) ¼ Flat Washers (24) ¼ Split Lock Washers (20) ¼-20 x ¾ long Button Head Screws
More informationInstallation Instructions
TOYOTA 16K Industry Standard Rail Custom Mounting Kit #2748 Gross Trailer Weight (Maximum)...16,000 lbs. Vertical Load Weight (Max. Pin Weight)...4,000 lbs. SYSTEM TOW CAPACITY Please note, in order to
More informationES&S Ballot on Demand Printing Procedures Manual
Better Elections Every Day ES&S Ballot on Demand Printing Procedures Manual Election Systems and Software, Inc. Corporate Headquarters 11208 John Galt Blvd. Omaha, NE 68137, USA Phone: (402) 593-0101 Toll
More informationWireless TFT LCD Monitor
Wireless TFT LCD Monitor Description Screen Ratio: 16 : 9 Resolution: 800*RGB*480 TV: PAL / NTCS Voltage: 10--28V Rated Capacity: 5W Brightness: 450cd/m2 Contrast: 450:1 Operate temperature: -20~65 Display
More informationE/ECE/324/Rev.1/Add.47/Rev.6/Amend.1 E/ECE/TRANS/505/Rev.1/Add.47/Rev.6/Amend.1
4 October 2010 Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles, Equipment and Parts which can be Fitted and/or be Used on Wheeled Vehicles and the Conditions for
More informationCHEV / GMC 3500 HD RT II TM UNDERCARRIAGE MOUNTING INSTRUCTIONS (PART NO. LTA03598)
BOSS PRODUCTS A Division of Northern Star Industries, Inc. P.O. Box 787 Iron Mountain MI 49801-0787 www.bossplow.com 1991-2002 CHEV / GMC 3500 HD RT II TM UNDERCARRIAGE MOUNTING INSTRUCTIONS (PART NO.
More informationFORD #2228. Gross Trailer Weight (Maximum)...24,000 lbs. Vertical Load Weight (Max. Pin Weight)...6,000 lbs. SYSTEM TOW CAPACITY
FORD 24K Industry Standard Rail Heavy Duty Custom Mounting Kit #2228 Gross Trailer Weight (Maximum)...24,000 lbs. Vertical Load Weight (Max. Pin Weight)...6,000 lbs. SYSTEM TOW CAPACITY Please note, in
More informationTOYOTA PRIUS BODY SIDE MOLDING Preparation
Preparation Part Number: PT938-47160-XX Kit Contents Item # Quantity Reqd. Description 1 1 Molding, LH Front Door 2 1 Molding, LH Rear Door 3 1 Molding, RH Front Door 4 1 Molding, RH Rear Door Hardware
More informationDFTG-1305 Technical Drafting Prof. Francis Ha
DFTG-1305 Technical Drafting Prof. Francis Ha Session 4 Orthographic Projection (or Multiview Projection) Reading: Geisecke s textbook: 14 th Ed. Chapter 5 p.162 15 th Ed. Chapter 6 p.232 Update: 18-0205
More informationInstallation Instructions
DODGE 16K Industry Standard Rail Custom Mounting Kit #2728 Gross Trailer Weight (Maximum)...16,000 lbs. Vertical Load Weight (Max. Pin Weight)...4,000 lbs. SYSTEM TOW CAPACITY Please note, in order to
More informationTonneau Cover Fitting Instructions Holden Colorado with Factory Sports Bars July 2012 Currrent Part Number: STO10054 Package includes
Tonneau Cover Fitting Instructions Holden Colorado with Factory Sports Bars July 2012 Currrent Part Number: STO10054 Package includes D 1 x Tonneau Cover D 1 x Rope Track (1460mm) D 2 x Bar Bracket (300474)
More informationCellular Shades SLUMBERSHADE. with energy saving blackout sidetracks. Installation & Care Instructions
Cellular Shades SLUMBERSHADE with energy saving blackout sidetracks Installation & Care Instructions 152725 B 9/14/2017 GETTING STARTED A few simple tools are required: - Measuring tape - Power drill,
More informationBefore you start, make sure that you have a properly calibrated system to obtain high-quality images.
CONTENT Step 1: Optimizing your Workspace for Acquisition... 1 Step 2: Tracing the Region of Interest... 2 Step 3: Camera (& Multichannel) Settings... 3 Step 4: Acquiring a Background Image (Brightfield)...
More informationCOFDM Multifunctional Receiver Operation Instructions
COFDM Multifunctional Receiver Operation Instructions Chapter Ⅰ (1) stand a good receiving antenna. Sucker whip antenna on the outside or the roof as possible, try to rod-shaped antenna mounted on the
More informationPoint Calibration. July 3, 2012
Point Calibration July 3, 2012 The purpose of the Point Calibration process is to generate a map of voltages (for galvos) or motor positions of the pointing device to the voltages or pixels of the reference
More informationThree vertical L angles must be riveted to each main spar (length = 206mm see boxed diagram on drawing 7-V-2).
Cut over-sized (left); Trim and file (above). Note: Six needed. Three vertical L angles must be riveted to each main spar (length = 206mm see boxed diagram on drawing 7-V-2). Trace line down center of
More informationDigital Camera Exercise
Commands Used New Part This lesson includes Sketching, Extruded Boss/Base, Extruded Cut, Fillet, Chamfer and Text. Click File, New on the standard toolbar. Select Part from the New SolidWorks Document
More informationBefore Assembling the Storage Wall
Chapter 1 Assembling the Lista Storage Wall Lista provides two types of standard Storage Walls: B251 and B255. The design, construction, assembly, and quality are identical for both types, however, B251
More informationModule 1E: Parallel-Line Flat Pattern Development of Sheet- Metal Folded Model Wrapping the 3D Space of An Oblique Circular Cylinder
Inventor (10) Module 1E: 1E- 1 Module 1E: Parallel-Line Flat Pattern Development of Sheet- Metal Folded Model Wrapping the 3D Space of An Oblique Circular Cylinder In this Module, we will explore the topic
More informationBentleyuser.dk Årsmøde 2010 Nordic Civil 2010
Bentleyuser.dk Årsmøde 2010 Nordic Civil 2010 8.-10. November 2010, Munkebjerg Hotel, Vejle Workshop - X9 Resurfacing and Overlay Tools InRoads V8i Presenter: Joe Waxmonsky, P.E., Bentley Systems USA Bentley
More informationDrawing with precision
Drawing with precision Welcome to Corel DESIGNER, a comprehensive vector-based drawing application for creating technical graphics. Precision is essential in creating technical graphics. This tutorial
More informationMultiview Projection
DFTG-1305 Technical Drafting Prof. Francis Ha Session 4 Multiview Projection (or Orthographic Projection) Reading: Geisecke s textbook: 14 th Ed. Chapter 5 p.162 15 th Ed. Chapter 6 p.232 Update: 17-0510
More informationINSTALLATION SPECIFICATION REV. 000, PAGE 1 OF 16
AUTOLIV INC. THIS DOCUMENT AND THE DATA DISCLOSED HEREIN OR HEREWITH IS PROPRIETARY AND MAY NOT BE REPRODUCED, USED OR DISCLOSED IN WHOLE OR IN PART WITHOUT WRITTEN PERMISSION FROM AUTOLIV INC. REVISION
More informationHow to Create Website Banners
How to Create Website Banners In the following instructions you will be creating banners in Adobe Photoshop Elements 6.0, using different images and fonts. The instructions will consist of finding images,
More informationPreparing Files for Press Printed Products. Press Printed Cards. Key Points. Sizing and Bleed. Download Free Sizing Templates
Preparing Files for Press Printed Products Press Printed Cards Key Points Sizing and Bleed All of our Press Printed Products are printed as full bleed products. This means that final trimmed product can
More informationAssembly, Installation, Operation and Maintenance Instructions Kit, Base Rail Bracket Part # 31852
. Assembly, Installation, Operation and Maintenance Instructions Kit, Base Rail Bracket Part # 31852 Dealer / Installer: Provide a copy of these instructions to the end user of this product. These instructions
More informationRadar Scanning for Development of Vehicle and Pedestrian Surrogate Targets for Vehicle Pre-Collision System (PCS) Testing
Radar Scanning for Development of Vehicle and Pedestrian Surrogate Targets for Vehicle Pre-Collision System (PCS) Testing Rini Sherony Collaborative Safety Research Center Toyota Motor Engineering & Manufacturing
More informationInstallation Instructions
DODGE RAM 2500 20K Industry Standard SuperRail Custom Mounting Kit #2336 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note,
More informationTOYOTA Tundra 2014 Fender Flare Set
2014 Part Number: 00016-34047 Accessory Code: TG1 Conflicts Note: Regular Cab Kit Contents Item # Quantity Reqd. Description 1 1 Left Front Fender Flare 2 1 Right Front Fender Flare 3 1 Left Rear Fender
More informationGENERAL NOTES: Page 1 of 9
Laminating A Zia Into A Turning Blank by W. H. Kloepping, Jan. 2009 This describes how a zia (the New Mexico state symbol) can be laminated into a turning blank. Materials needed: Square Turning Block
More informationStandard Operating Procedure
Standard Operating Procedure Nanosurf Atomic Force Microscopy Operation Facility NCCRD Nanotechnology Center for Collaborative Research and Development Department of Chemistry and Engineering Physics The
More informationTITLE DATE PERIOD YOUR NAME
Step A. Line up paper up with T-Square and tape down corners. Border Lines and Title Block Step B. Measure in from each edge.2. Draw in border lines. Step C. Measure up from bottom border line.1,.2 and
More informationUNIT 5a STANDARD ORTHOGRAPHIC VIEW DRAWINGS
UNIT 5a STANDARD ORTHOGRAPHIC VIEW DRAWINGS 5.1 Introduction Orthographic views are 2D images of a 3D object obtained by viewing it from different orthogonal directions. Six principal views are possible
More informationEmbroideryWorks Cute as a Caterpillar Bulletin Board
EmbroideryWorks Cute as a Caterpillar Bulletin Board Create this darling appliquéd bulletin board in an afternoon using the updated version of EmbroideryWorks with built-in AccuQuilt shapes. Think outside
More informationFRAME BRACKET Chevy Silverado 1500 & GMC Sierra /2 & 6-1/2 Box
, Rev 1 01/19 FRAME BRACKET 8551011 Chevy Silverado 1500 & GMC Sierra 1500 5-1/2 & 6-1/2 Box ITEM PART # QTY DESCRIPTION 1 10379 8 1/2" UNC FLANGED NUT 2 14266 8 BOLT,.50 NC X 1.75 GR5 HEX W/ KNURLED NECK
More informationDescribing an Angle Bracket
Basics of Drafting Describing an Angle Bracket Orthographic Projection Orthographic drawings represent three dimensional objects in three separate views arranged in a standard manner. Orthographic Views
More informationTOY TRUCK. Figure 1. Orthographic projections of project.
TOY TRUCK Prepared by: Harry Hawkins The following project is of a small, wooden toy truck. This exercise will provide you with the procedure for constructing the various parts of the design then assembling
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions Honda CRV 1997-2003 THE safety accessory of the 21 st Century. P/N 210-0032-0 Rev B2 (6-26-04), GG 2003 Muth Mirror Systems, LLC. Note: Professional Installation
More informationDO NOT EXCEED LOWER OF TOWING VEHICLE MANUFACTURER'S RATINGS OR THOSE LISTED BELOW:
CATALOG NO. 40050 INSTALLATION INSTRUCTIONS NOTE: CHECK HITCH FREQUENTLY, MAKING SURE ALL FASTENERS AND BALL ARE PROPERLY TIGHTENED. A HITCH OR BALL WHICH HAS BEEN DAMAGED SHOULD BE REMOVED AND REPLACED.
More informationInstallation Instructions Universal Crossmember Kit - 60 Track Width BEFORE Measure Twice, Weld Once! II
Installation Instructions Universal Crossmember Kit - 60 Track Width Please read these instructions completely BEFORE starting your installation. Remember the basic rule for a successful installation:
More informationAluminum Sprinter Rack Installation
INSTALLATION INSTRUCTIONS MyGlassTruck.com Division of Demountable Concepts, Inc Aluminum MyGlassTruck.Com Demountable Concepts, Inc. 200 Acorn Rd. Glassboro, NJ 08028 800.254.3643 toll free 856.863.0900
More informationRH-412 STEEL DOORS INSTALLATION INSTRUCTIONS
RH-412 STEEL DOORS INSTALLATION INSTRUCTIONS By following the steps outlined below, the assembly, installation and adjustment of the steel doors, will be a simple process. Let s start with the Driver Side.
More informationHow to combine images in Photoshop
How to combine images in Photoshop In Photoshop, you can use multiple layers to combine images, but there are two other ways to create a single image from mulitple images. Create a panoramic image with
More informationSHAPE CLUSTER PHOTO DISPLAY
SHAPE CLUSTER PHOTO DISPLAY In this Photoshop tutorial, we ll learn how to display a single photo as a cluster of shapes, similar to larger wall cluster displays where several photos, usually in different
More informationBali DIY Shutters Your Simple Guide to Measuring & Installation
Bali DIY Shutters Your Simple Guide to Measuring & Installation Free reverso en español Determine Your Wood-wrapped window MOLDING INSIDE MOUNT INSIDE MOUNT A Inside Mount Hang Strips Shutters are mounted
More informationTraining CAD/ Part Designer: Designing with Angled Parts
Training CAD/ Part Designer: Designing with Angled Parts We have attempted to keep the content of this document complete, accurate and under permanent review. However, due to the continuous development,
More informationFull Overlay Door Panel Preparation and Installation Instructions for 2175, 2115, CLR2160 Models
Full Overlay Door Panel Preparation and Installation Instructions for 2175, 2115, CLR2160 Models www.u-lineservice.com Phone (414) 354-0300 FAX (414) 354-7905 Service & Parts Tech Lines Phone (800) 779-2547
More information