PRODUCT DATASHEET Mira series last update 17/4/2012

Transcription

1 PRODUCT DATASHEET Mira series last update 17/4/2012 Ordering number C12500_MIRAM Family Type LED Color Diameter Height Style Optic Material Holder Material Fastening Status Mira Lens MTG Clear 32.4 mm 14.7 mm Round Ready FWHM Efficiency cd/lm Gerber File 28 degrees 83 % Available Ordering number CA12503_MIRAM Family Type LED Color Diameter Height Style Optic Material Holder Material Fastening Status Mira Assembly MTG White 35 mm 15.8 mm Round Tape Ready FWHM Efficiency cd/lm Gerber File 28 degrees 83 % Available Ordering number C12501_MIRAW Family Type LED Color Diameter Height Style Optic Material Holder Material Fastening Status Mira Lens MTG Clear 32.4 mm 14.7 mm Round Ready FWHM Efficiency cd/lm Gerber File 38 degrees 80 % Available Ordering number CA12504_MIRAW Family Type LED Color Diameter Height Style Optic Material Holder Material Fastening Status Mira Assembly MTG White 35 mm 15.8 mm Round Tape Ready FWHM Efficiency cd/lm Gerber File 44 degrees 82 % Available October 19th :21 Copyright Ledil Oy Subject to change without prior notice Page 1/3 Ledil Oy Salorankatu SALO Finland ledil@ledil.com FAX:

2 PRODUCT DATASHEET Mira series last update 17/4/2012 Ordering number C12502_MIRAWW Family Type LED Color Diameter Height Style Optic Material Holder Material Fastening Status Mira Lens MTG Clear 32.4 mm 14.7 mm Round Glue Ready FWHM Efficiency cd/lm Gerber File 58 degrees 81 % Available Ordering number CA12505_MIRAWW Family Type LED Color Diameter Height Style Optic Material Holder Material Fastening Status Mira Assembly MTG White 35 mm 15.8 mm Round Tape Ready FWHM Efficiency cd/lm Gerber File 66 degrees 81 % Available NOTE: The typical divergence will be changed by different color, chip size and chip position tolerance. The typical total divergence is the full angle measured where the luminous intensity is half of the peak value. October 19th :21 Copyright Ledil Oy Subject to change without prior notice Page 2/3 Ledil Oy Salorankatu SALO Finland ledil@ledil.com FAX:

3 PRODUCT DATASHEET Mira series last update 17/4/2012 GENERAL INFORMATION Product series especially designed & optimized for MTG series of LEDs. Special care taken to make light distribution as uniform as possible. Lens material optical grade with high UV and temperature resistance (120 degrees of Celcius / 248 degrees of Fahrenheit). Allows use of high current and temperature conditions. Please find more information about used materials from below: Optic holder molded by high quality material (120 dergees of Celcius / 248 degrees of Fahrenheit). Fastening to heat sink with a PU foam adhesive tape of automotive grade. Please find fastening details by clicking link: Fastening to B with appropriate adhesive. By clicking link below you can find Ledil recommended glue options. NOTE 1: We advise customer to ensure the suitability and sufficiency of the bond in the end product. For example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the tape. NOTE 2: Assembly to the surface must be made straight, so the tape bonds constant and balanced with fastening surface. Slanted assembly might cause unbalanced bond to the surface. All surfaces where tape is applied must be clean, dry and free from grease and dirt. If cleaning of B surfaces is needed, please follow strictly the cleaning instructions of your LED manufacturer this is important as cleaning shall under no circumstances damage LEDs or other electronics components on the B. Further note that optical components shall not be cleaned with any chemicals only micro fiber cloth may be used to remove fingerprints or other traces from handling. NOTE 1: We advise customer to ensure the suitability and sufficiency of the bond in the end product. For example, mechanical stress, vibration and holes on the surface of the circuit boar weaken the strength of the glue. NOTE 2: All surfaces where glue is applied must be clean, dry and free from grease and dirt. If cleaning of B surfaces is needed, please follow strictly the cleaning instructions of your LED manufacturer this is important as cleaning shall under no circumstances damage LEDs or other electronics components on the B. Further note that optical components shall not be cleaned with any chemicals only micro fiber cloth may be used to remove fingerprints or other traces from handling. October 19th :21 Copyright Ledil Oy Subject to change without prior notice Page 3/3 Ledil Oy Salorankatu SALO Finland ledil@ledil.com FAX:

4 Relative intensity of C12501_MIRAW 100% 75% 50% 25% % 60

5 Relative intensity of C12502_MIRAWW (MTG) 100% 75% 50% 25% % 70

6 Relative intensity of CA12505_MIRAWW (MTG) 100% 75% 50% 25% % 70

7 D C B A 4 D 4 Isometric view Bottom view Front view Dimension D: C12500_MIRAM 29,7mm C12501_MIRAW 28,4mm C12502_MIRAWW 28,4mm Top view Material: 1 This drawing is our property. It can't be reproduced or communicated without our written agreement. DRAWN BY CHECKED BY DESIGNED BY D DATE mav sn mav DATE DATE DRAWING TITLE SIZE A4 DRAWING NUMBER Ledil Oy Salorankatu 10 FIN SALO Finland Datasheet MIRA lens SCALE 1:1 WEIGHT(g) SHEET 1/1 A REV 1 1

8

9

10

11

12

13