MODEL 2900 Downflow. Service Manual. IMPORTANT: Fill in pertinent information on page 3 for future reference.

Transcription

1 Downflow Service Manual IMPORTANT: Fill in pertinent information on page 3 for future reference.

2 Table of Contents General Commercial Pre-Installation Check List Installation Instructions Timer Setting Procedure Timer Settings Regeneration Cycle Program Setting Procedure Timer Assembly Timer Assembly Environmental Power Head Lower Environmental Power Head Designer Power Head Lower Designer Power Head Control Valve Body Brine System Brine System Brine System Brine System Meter Assembly Plastic Meter Assembly Safety Brine Valve Safety Brine Valve Safety Brine Valve Service Valve Operator Control Valve Side Mount Adapter Service Assemblies Service Instructions Service Position Backwash Position Brine Position Slow Rinse Position Rapid Rinse Brine Tank Fill Position Flow Data & Injector Draw Rates Environmental Backplate Line Drawing Environmental Designer System #4 - Typical Single Tank Installation With Optional Meter System #5 - Interlock - Typical Twin Tank Installation With Optional Meter Interlock And No Hard Water Bypass System #6 Twin Series Regeneration System #7 Twin Alternator Installation System #4-Single Valve Regeneration Immediate and Delayed Valve Wiring System #4-With Remote Signal Start Valve Wiring system #5-Interlocked Regeneration Valve Wiring system #6-Series Regeneration Valve Wiring system #7-Alternating Regeneration Valve Wiring system #7-Alternating Regeneration Multi-Valve System Valve Wiring IMPORTANT: The information, specifications and illustrations in this manual are based on the latest information available at the time of printing. The manufacturer reserves the right to make changes at any time without notice.

3 Job Specification Sheet JOB NO. MODEL NO. WATER TEST CAPACITY PER UNIT MAX. PER REGENERATION MINERAL TANK SIZE DIA. HEIGHT BRINE TANK SIZE & SALT SETTING PER REGENERATION: 2900 CONTROL VALVE SPECIFICATIONS 1) Type of Timer (see pages 18-21) A) 7 day or 12 day B) * 1,250 to 21,250 gallon meter or * 6,250 to 106,250 gallon meter * Other C) Meter Wiring Package 1) System #4-1 tank; 1 meter; immediate or delayed regeneration 2) System #5-2 tanks; 2 meters; interlock 3) System #6-2 tanks; 1 meter; series regeneration 4) System #7-2 tanks; 1 meter; alternator 2) Timer Program Settings (see pages 18 and 19) A) Backwash min. B) Brine & Slow Rinse min. C) Rapid Rinse min. D) Brine Tank Refill min. 3) Drain Line Flow Controllergpm 4) Brine Line Flow Controller - 5) Injector Size # 6) A) Hard Water By-Pass B) No Hard Water By-Pass Page 3

4 General Commercial Pre-Installation Check List WATER PRESSURE: A minimum of 25 pounds of water pressure is required for regeneration valve to operate effectively. ELECTRICAL FACILITIES: A continuous 110 volt, 60 Hertz current supply is required. Make certain the current supply is always hot and cannot be turned off with another switch. EXISTING PLUMBING: Condition of existing plumbing should be free from lime and iron buildup. Piping that is built up heavily with lime and/or iron should be replaced. If piping is clogged with iron, a separate iron filter unit should be installed ahead of the water softener. LOCATION OF SOFTENER AND DRAIN: The softener should be located close to a drain. BY-PASS VALVES: Always provide for the installation of a by-pass valve. CAUTION: Water pressure is not to exceed 120 p.s.i., water temperature is not to exceed 100 F, and the unit cannot be subjected to freezing conditions. Installation Instructions 1. Place the softener tank where you want to install the unit making sure the unit is level and on a firm base. (Maximum 4 feet apart for twin units.) 2. All plumbing should be done in accordance with local plumbing codes. The pipe size for the drain line should be the same size as the drain line flow control female connection. Water meters are to be installed on soft water outlets. Twin units with (1) one meter shall be installed on common soft water outlet of units. 3. Solder joints near the drain must be done prior to connecting the Drain Line Flow Control fitting. Leave at least 6 between the DLFC and solder joints when soldering when the pipes are connected on the DLFC. Failure to do this could cause interior damage to the DLFC. 4. Teflon tape is the only sealant to be used on the drain fitting. The drain from twin units may be run through a common line. 5. Make sure that the floor is clean beneath the salt storage tank and that it is level. 6. Place approximately 1 of water above the grid plate (if used) in your salt tank. Salt may be placed in the unit at this time. 7. On units with a by-pass, place in by-pass position. Turn on the main water supply. Open a cold soft water tap nearby and let run a few minutes or until the system is free from foreign material (usually solder) that may have resulted from the installation. 8. Place the by-pass in service position. 9. Manually index the softener control into service position and let water flow into the mineral tank. When water flow stops, open a cold water tap nearby and let run until air pressure is relieved. 10. Electrical: All electrical connections must be connected according to codes. Use electrical conduit if applicable. Remote meter systems and Twin meter system wiring diagrams are on pages Plug into power supply. Page 4

5 3200 Timer Setting Procedure How To Set Days On Which Water Conditioner Is To Regenerate: Rotate the skipper wheel until the number 1 is at the red pointer. Set the days that regeneration is to occur by sliding tabs on the skipper wheel outward to expose trip fingers. Each tab is one day. Finger at red pointer is tonight. Moving clockwise from the red pointer, extend or retract fingers to obtain the desired regeneration schedule. How To Set The Time Of Day: Press and hold the red button in to disengage the drive gear. Turn the large gear until the actual time of day is at the time of day pointer. Release the red button to again engage the drive gear. How To Manually Regenerate Your Water Conditioner At Any Time: Turn the manual regeneration knob clockwise. This slight movement of the manual regeneration knob engages the program wheel and starts the regeneration program. The black center knob will make one revolution in the following approximately three hours and stop in the position shown in the drawing. Even thought it takes three hours for this center knob to complete one revolution, the regeneration cycle of your unit might be set only one half of this time. In any event, conditioned water may be drawn after rinse water stops flowing from the water conditioner drain line. SERVICE POSITION INDICATOR RED TIME SET BUTTON 24 HR. GEAR MANUAL REGENERATION KNOB SKIPPER WHEEL, 12 DAY (SHOWS EVERY OTHER DAY REGENERATION) How to Adjust Regeneration Time: 1. Disconnect the power source. 2. Locate the three screws behind the manual regeneration knob by pushing the red button in and rotating the 24 hour dial until each screw appears in the cut out portion of the manual regeneration knob. 3. Loosen each screw slightly to release the pressure on the time plate from the 24 hour gear. 4. Locate the regeneration time pointer on the inside of the 24 hour dial in the cut out. 5. Turn the time plate so the desired regeneration time aligns next to the raised arrow. 6. Push the red button in and rotate the 24 hour dial. Tighten each of the three screws. 7. Push the red button and locate the pointer one more time to ensure the desired regeneration time is correct. 8. Reset the time of day and restore power to the unit ADJUSTABLE REGENERATION TIMER Page 5

6 3210 Timer Settings Typical Programming Procedure Calculate the gallon capacity of the system, subtract the necessary reserve requirement and set the gallons available opposite the small white dot on the program wheel gear. Note, drawing shows 8,750 gallon setting. The capacity (gallons) arrow denotes remaining gallons exclusive of fixed reserve. How To Set The Time Of Day: Press and hold the red button in to disengage the drive gear. Turn the large gear until the actual time of day is opposite the time of day pointer. Release the red button to again engage the drive gear. How To Manually Regenerate Your Water Conditioner At Any Time: Turn the manual regeneration knob clockwise. This slight movement of the manual regeneration knob engages the program wheel and starts the regeneration program. The black center knob will make one revolution in the following approximately three hours and stop in the position shown in the drawing. Even though it takes three hours for this center knob to complete one revolution, the regeneration cycle of your unit might be set for only one half of this time. In any event, conditioned water may be drawn after rinse water stops flowing from the water conditioner drain line. Immediate Regeneration Timers: These timers do not have a 24 hour gear. Setting the gallons on the program wheel and manual regeneration procedure are the same as previous instructions. * 24 HOUR GEAR MANUAL REGENERATION KNOB SERVICE POSITION INDICATOR PROGRAM WHEEL NOTE: To set meter capacity rotate manual knob one revolution to set gallonage. RED TIME SET BUTTON WHITE DOT GALLONS LABEL * Immediate regeneration timers do not have 24 hour gear. No time of day can be set. Page 6

7 MODEL 3200 & 3210 TIMER SERIES Regeneration Cycle Program Setting Procedure (Brine Tank Refill Separate From Rapid Rinse) How To Set The Regeneration Cycle Program: The regeneration cycle program on your water conditioner has been factory preset, however, portions of the cycle or program may be lengthened or shortened in time to suit local conditions & 3210 Series Timers (Figure to Right) To expose cycle program wheel, grasp timer in upper lefthand corner and pull, releasing snap retainer and swinging timer to the right To change the regeneration cycle program, the program wheel must be removed. Grasp program wheel and squeeze protruding lugs toward center, lift program wheel off timer. (Switch arms may require movement to facilitate removal.) Return timer to closed position engaging snap retainer in back plate. Make certain all electrical wires locate above snap retainer post Timer Setting Procedure for 3200 & 3210 Timer How To Change The Length Of The Backwash Time: The program wheel as shown in the drawing is in the service position. As you look at the numbered side of the program wheel, the group of pins starting at zero determines the length of time your unit will backwash. FOR EXAMPLE: If there are six pins in this section, the time of backwash will be 12 min. (2 min. per pin). To change the length of backwash time, add or remove pins as required. The number of pins times two equals the backwash time in minutes. How To Change The Length Of Brine And Rinse Time: The group of holes between the last pin in the backwash section and the second group of pins determines the length of time that your unit will brine and rinse (2 min. per hole.) To change the length of brine and rinse time, move the rapid rinse group of pins to give more or fewer holes in the brine and rinse section. Number of holes times two equals brine and rinse time in minutes. How To Change The Length Of Rapid Rinse: The second group of pins on the program wheel determines the length of time that your water conditioner will rapid rinse. (2 min. per pin.) BRINE & RINSE SECTION (2 MIN. PER HOLE) PIN STORAGE BACKWASH SECTION (2 MIN. PER PIN) PROGRAM WHEEL FOR CONTROL OF REGENERATION CYCLE RAPID RINSE SECTION (2 MIN. PER PIN) BRINE TANK REFILL SECTION (2 MIN. PER HOLE) To change the length of rapid rinse time, add or remove pins at the higher numbered end of this section as required. The number of pins times two equals the rapid rinse time in minutes. How To Change The Length Of Brine Tank Refill Time: The second group of holes in the program wheel determines the length of time that your water conditioner will refill the brine tank (2 min. per hole.) To change the length of refill time, move the two pins at the end of the second group of holes as required. The regeneration cycle is complete when the outer microswitch is tripped by the two pin set at end of the brine tank refill section. The program wheel, however, will continue to rotate until the inner micro-switch drops into the notch on the program wheel. Page 7

8 3200 Timer Assembly (See opposite page for parts list) Page 8

9 3200 Timer Assembly Parts List Item No. No. Req d Part No. Description Timer Housing Cycle Actuator Arm Hour Gear Assembly, 12 Midnight Hour Gear Assembly, 2 a.m Knob Screw - Timer Knob and Motor Mtg. Plate Button Decal Skipper Wheel Assembly - 12 Day Skipper Wheel Assembly - 7 Day Regeneration Pointer Spring Clip Spring - Skipper Wheel Detent Ball - 1/4 in. Dia. Skipper Wheel Spring - Main Gear Detent Main Drive Gear Program Wheel Roll Pin Idler Shaft Spring - Idler Idler Gear Drive Gear Motor Mounting Plate Motor - 120V., 60 Hz Motor - 24V., 60 Hz Screw - Motor Mounting Screw - Timer Hinge & Ground Wire Hinge Bracket Insulator Switch Switch Screw - Switch Mounting Decal - Time of Day Decal - Instructions Skipper Wheel Ring Ball 1/4 in. Dia. Main Gear Not Shown Harness Not Shown Wire Connector Not Shown Ground Wire Page 9

10 3210 Timer Assembly (See opposite page for parts list) Page 10

11 3210 Timer Assembly Parts List Item No. Quantity Part No. Description Timer Housing Assembly Cycle Actuator Gear Hour Gear Assembly, 12 Midnight Hour Gear Assembly, 2 A.M Knob Screw - Timer Knob & Motor Plate Mtg Button Decal Program Wheel Assembly, 0-21, Program Wheel Retainer Screw - Program Wheel Mtg Spring Clip Spring-Detent Ball - 1/4 in. dia Main Drive Gear Program Wheel Assembly Roll Pin Not Assigned Idler Shaft Spring - Idler Idler Gear Drive Gear Motor Mounting Plate Motor - 110V., 60 Hz Motor - 24V., 60 Hz Screw - Motor Mounting Drive Pinion - Program Wheel Clutch - Drive Pinion Spring Spring Retainer Not Assigned Screw - Timer Hinge & Ground Wire Hinge Bracket Insulator Switch Switch Screw - Switch Mounting Decal - Time of Day Decal - Instructions Harness - Not Shown Wire Connector - Not Shown Ground Wire - Not Shown Caution Label - Not Shown Capacity Label - Not Shown Page 11

12 Environmental Power Head (See opposite page for parts list) Page 12

13 Environmental Power Head Parts List Item No. Quantity Part No. Description Back Plate, Hinged, Clock Timer Assy Clock Timer Assy Meter Timer Assy Meter Timer Assy Motor, Drive, Shaded Pole, 115V, 60HZ, Fam Bracket, Motor CAM Drive Assy, STF, Black Bushing, Heyco 1/2, Heyco # Screw, Hex Wsh, 8-32 X 17/ Insulator, Limit Switch Switch, Micro Screw, Pan Hd Mach, 4-40 X Bracket, Motor, Aux Switch Switch, Miniature Screw, Rd Hd, 4-40 X 5/8 Type Cam, Shut-off Valve Pin, Roll, 2900/ Nut, Jam, 3/ Fitting, Brine Valve Harness, Plug,.750 Dia. Hole, Flush Hole Plug, (Heyco) Plug,.190 Hole Conduit, Interdrive Fitting, Conduit Washer, Sealing - 3/8" Plug (Hole Size: Dia.140) Screw, Slot Hex Wsh, 8-18 X 3/ Nut, Conduit Fitting,1/2IN Label, Voltage, 120V Hole Plug, (Heyco) Cover Assy, Environmental,Black W/Clear Window Bracket, Terminal Block Terminal Block, Green/Yellow Terminal Block, Segment, Gray Endplate, Terminal Block, Gray Label, Terminal Strip Screw, Hex Washer, 6-20 X 1/ Harness, Drive, DesignR/Envirmtl Wire, Ground, 7.5 Long Power Cord, 12' US, Round, 120V Strain Relief, Round Cord (Not Shown)..... Fitting Assy, Liquid-Tight, Black Page 13

14 Lower Environmental Power Head (See opposite page for parts list) Page 14

15 Lower Environmental Power Head Parts List Item No. Quantity Part No. Description Back, Plate, Lower Screw, Screw, Slotted Hex Head, 5/16-18 X 5/ Nut, Hex, Jam, 5/16-18, 18-8 S.S Washer, Sealing - 3/8" Fitting, Conduit Nut, Conduit Fitting,1/2in Motor, Drive,115v,60hz,Sp, Fam Bracket, Motor, Harness, Lead, Sys#4, Designer Insulator, Limit Switch Switch, Micro Screw, Pan Hd, 4-40 X 5/ Pin- Connecting Rod Cam, Main Drive, 2900 Lower Pin, Roll, 2900/ Link, Piston Rod Ring, Retaining Indicator, Service/Standby Spacer, Indicator Screw, Hex Wsh,8-32 X 17/ (Not Shown)..... Tie, Cable, Heyco, Vnt# Cover Assy, 2900, Lower, Black, Environmental Page 15

16 Designer Power Head (See opposite page for parts list) Page 16

17 Designer Power Head Parts List Item No. Quantity Part No. Description Backplate, SS/SVO, W/T-Screws, 2750,2850, Meter Timer Assy Meter Timer Assy Clock Timer Assy Clock Timer Assy Bracket, Motor, Aux Switch Motor, Drive, Shaded Pole, 115V, 60HZ, Fam Bracket, Motor CAM Drive Assy, STF, Black Bushing, Heyco 1/2, Heyco # Screw, Hex WSH, 8-32 X 17/ Insulator, Limit Switch Switch, Micro Screw, Pan HD Mach, 4-40 X Switch, Miniature Screw, RD HD, 4-40 X 5/8 Type Cam, Shut-off Valve Pin, Roll, 2900/ Nut, Jam, 3/ Fitting, Brine Valve Harness, Terminal Block, Green/Yellow Terminal Block, Segment, Gray Endplate, Terminal Block, Gray Label, Terminal Strip Screw, Hex Washer, 6-20 X 1/ Power Cord, 12'US, Round, 120V Strain Relief, Round Cord Hole Plug, (Heyco) Hole Plug, (Heyco) Plug, 3/4", Knock-out, Heyco # Screw, Slot Hex Wsh, 8-18 X 3/ Label, Voltage, 120V Harness, Drive, Designr/Envirmtl Wire, Ground, 7.5 Long (Not Shown)..... Fitting Assy, Liquid-Tight, Black (Meter) (Not Shown)..... TD Cable Guide (Meter) Cover, Designer Page 17

18 Lower Designer Power Head (See opposite page for parts list) Page 18

19 Lower Designer Power Head Parts List Item No. Quantity Part No. Description Backplate, Lower Bracket, Motor, SCREW Slotted Hex Head, 5/16-18 x 5/ Nut, Hex, Jam, 5/16-18, 18-8 S.S SR 7W Motor, Drive, 115V, 60HZ, SP, Fam Ring, Retaining Link, Piston Rod Bearing, Connecting Rod Cam, Main Drive, 2900 Lower Pin, Roll, 2900/ Screw, Pan Hd, 4-40 X 5/ Switch, Micro Insulator, Limit Switch Harness, Lead, Sys#4, Designer Screw, Hex Wsh, 8-32 X 17/ (Not Shown)..... Tie, Cable, Heyco, Vnt# Cover, Dust, Lower, 2900, Black Screw, Designer Cover, Thumb Page 19

20 Control Valve Body (See opposite page for parts list) Page 20

21 Control Valve Body Parts List Item No. Quantity Part No. Description Valve Body, 2900 CPI, Machined xx Valve Body, 2900 CPI, Machined, W/Soft Water Adapt Spacer, End Seal, Piston Spacer, 1 2 Hole Piston, 2900 CPI, Upper, D/F Piston, Retainer, Piston Rod Rod, Piston End Plug Ppin, Connecting Rod Spring Quad Ring, O-ring, 28MM X 2MM Seal, Piston, 2900/ Spacer, 2", 2900/ Spacer, Piston No HWBP Ring, Piston Rod, Snap Piston Rod O-ring, Quad ring "O" ring Connecting Link Pin O-ring, O-ring, Gasket, Injector Body Cap, Injector, SS Screw, Hex Washer Head, #10-24 X 3/ Adapter, Softwater Regen, O-ring, O-ring, -020 Page 21

22 1600 Brine System Item No. Quantity Part No. Description Elbow - ¼ Pipe Thd. to 3/8 Tube Brine Line Screen Insert Sleeve 3/8 Tube) Fitting Nut (3/8 Tube) Derlin Sleeve (3/8 Tube) Brine Valve Tube Retaining Ring Stem Guide Brine Valve Spring Quad Ring Brine Valve Body Brine Valve Stem Brine Valve Seat O-Ring BLFC.25GPM BLFC.50 GPM BLFC 1.0 GPM Screw, Slotted, Indented Hex Head, #10-24 X 5/ Cap, Injector, SS Gasket, Injector Body Screen, Injector Nozzle, Injector, Std Injector Throat, Std Body, Injector, Disperser, Air Gasket, Injector Body Page 22

23 1650 Brine System Item No. Quantity Part No. Description Brine Valve Assembly, Includes Items 3-15 (Less BLFC ) Elbow, 90 1/4 NPT x 3/ Screen, Brine Line Insert, 3/ Sleeve, 3/8 Nut Brine Tube Fitting, 3/8 Nut Brine Tube, Brine Valve Assy., GFN Nut O-Ring Seat, Brine Valve Brine Valve Stem, Assy., GFN Nut Guide, Brine Valve Stem Retaining Ring Spring, Brine Valve Brine Valve Body Assy., Plastic BLFC.25GPM BLFC.50 GPM BLFC 1.0 GPM Screw, Slotted, Indented Hex Head, #10-24 X 5/ Cap, Injector, SS Gasket, Injector Body Screen, Injector Nozzle, Injector, Std Injector Throat, Std Body, Injector, Disperser, Air Gasket, Injector Body Page 23

24 1700 Brine System Page 24

25 1700 Brine System Parts List Item No. Quantity Part No. Description End Plug O-Ring - End Plug Flow Washer 1.2 GPM Flow Washer 1.5 GPM Flow Washer 2.0 GPM Flow Washer 2.4 GPM Flow Washer 3.0 GPM Flow Washer 3.5 GPM Flow Washer 4.0 GPM Flow Washer 5.0 GPM Flow Control Retainer Piston Seals Spacer Brine Valve Piston Brine Valve Stem Brine Valve Body Quad Ring - Brine Stem Spring - Brine Valve Retaining Ring Stem Guide Insert Nut Ferrule 1/ Elbow Brine Tube Tube Nut 1/ Ferrule 1/ Fitting, Brass, Female 3/4 x 3/4 Slip - Not Shown Injector Cover Injector Cover Gasket Injector Body * Injector Throat * Injector Nozzle Injector Screen Screw, Hex Head Mach, #10-24 X 2 3/4" 18-8 SS *Injector Throat *Injector Nozzle Size Color C C.... #3C Yellow C C.... #4C Green C C.... #5C White C C.... #6C Red C C.... #7C Black Page 25

26 1710 Brine System Page 26

27 1710 Brine System Parts List Item No. Quantity Part No. Description Plastic Brine,Top Retainer, Flow Control O-Ring, -210, 560CD Spacer, Piston, Brine Valve Brine Valve Stem Plastic Brine, Bottom Ring, Quad Sleeve, Brine Valve Stem O-Ring, 2mmx35mm Spring, Brine Valve Ring, Retaining Guide, Brine Valve Stem Screw, Hex Wsh Mach, 8-32 X 5/16" Nut Assembly, 1/2" Washer, Flow, 1.0 Gpm (not shown) Label, Blfc, 1710 (not shown) Tube, Brine, Nut, 2900, W/Sleeve Gasket, Injector Body Body, Injector, C Throat, Injector O-ring, C Nozzle, Injector Gasket, Injector Body Cap, Injector Screw, Hex Head Mach, #10-24 X 2 3/4" 18-8 SS Fitting, Elbow, Male, 1/2T X 3/8NPT Page 27

28 2 Meter Assembly 8 7A 7B Item No. Quantity Part No. Description Meter Body Impeller Shaft Retainer Impeller Shaft Not Assigned Impeller O-Ring - Meter Cover 7A Meter Cover Assembly (Standard) 7B Meter Cover Assembly (Extended Range) Screw - Meter Cover O-Ring - Quick Connect Nipple - Quick Connect Flow Straightener Nut - Quick Connect Page 28

29 2 Plastic Meter Assembly Item No. Quantity Part No. Description Body, Meter, 2 Plastic Shaft, Impeller Seat Shaft, Impeller Meter Assembly, 2 (Standard Range) Meter Assembly, 2 (Extended Range) Meter Assembly, 2 (Electronic) Impeller Assembly, 2 Meter O-Ring, -137, Meter Meter Cap Assembly (Standard Range) Meter Cap Assembly (Extended Range) Meter Cap Assembly (Electronic) Screw, Hex Washer, x 5/ Seal, Face, 2, Plastic 10A Fitting, Nipple, 2, Plastic, NPT, Machined 10B Fitting, Nipple, 2, Plastic, BSP, Machined 11A Fitting, Nipple, 2, Plastic, NPT 11B Fitting, Nipple, 2, Plastic, BSP Flow Straightener Nut, 2 Meter Page 29

30 2300 Safety Brine Valve Item Quantity Part Number Description FFA 2300 safety brine valve, fitting facing arm FFS 2300 safety brine valve, fitting facing stud float assembly blue/white SAN float assembly green/green, hot water #500 air check #500 air check, hot water Page 30

31 2310 Safety Brine Valve Item Quantity Part Number Description safety brine valve float assembly float assembly red/white (float fill) #500 air check Page 31

32 2350 Safety Brine Valve Item Quantity Part Number Description safety brine valve 1A actuator assembly float assembly red/white SAN float assembly green/green (hot water) #900 air check #900 air check hot water Not Shown fittings for 1700 brine system #900 fittings for 1700 brine system Page 32

33 Service Valve Operator a b PARTS LIST Item No. Quantity Part No. Description Guide, Brine Valve Stem Retaining Ring Spring, Brine Valve Quad Ring Service Actuator Assembly -.25 gpm Brine Valve Stem, Seat, Brine Valve Insert, Sleeve, 3/8 Delrin Nut, 3/8 Brass Elbow, 90 1/4 NPT x 3/ Tube Connector, Male 1/8 NPT to 3/8 T 14a Cam Assy. Tri stack, After Rapid Rinse 14b Cam Assy. Tri stack, After Brine Tank Fill Bracket, Motor Outboard Page 33

34 Control Valve Side Mount Adapter 7 Item No. Quantity Part No. Description Adaptor, Side Mount O-Ring O-Ring Base, Rotating Washer Screw Assembly Page 34

35 Service Assemblies ADAPTERS METERS Treated Water Regen Adapter Assembly Meter brass standard range Sidemount Adaper Assembly Meter brass extended range 61415NP Sidemount Adaper Assembly, Nickel Plated Meter brass electronic Sidemount Adaper Assembly, BSP/Metric Meter plastic standard range NP Sidemount Adaper Assembly, BSP/Metric, Nickel Plated Meter plastic Extended range Meter plastic electronic AIR CHECKS ½ low flow sleeve only #500 Air Check #500 Air Check Hot Water PISTON ASSEMBLIES # 900 Commercial Air Check Top piston # 900 Commercial Air Check Hot Water Top piston, Hot Water Lower piston, Hard Water By-Pass AUXILARY MICRO SWITCH Lower piston, By-Pass, Treated Water Regen Series Timer Lower piston, By-Pass, Treated Water Regen, Hot Water Lower Drive (2nd Switch) Lower Piston, By-Pass, Hot Water Lower Drive (3rd Switch) Lower Piston, No By-Pass Lower Piston, No By-Pass, Treated Water Regen, Hot Water BRINE LINE FLOW (BLFC) Lower Piston, No By-Pass, Treated Water Regen Model 1600, blank Lower Piston, No By-Pass, Hot Water Model 1600 with.25 gpm flow control Model 1600 with.50 gpm flow control PROGRAM WHEEL ASSEMBLIES Model 1600 with 1.0 gpm flow control ½ Std. Range ( 0-10,000 ) Model 1650, blank Std. Range ( 0-21,000 ) Model 1650 with.25 gpm flow control Ext. Range ( 0-100,000 ) Model 1650 with.50 gpm flow control ½ Ext. Range ( 0-50,000 ) Model 1650 with 1.0 gpm flow control SAFETY BRINE VALVES BRINE VALVES Model 2310 plastic safety brine valve Model 1650 brine valve assy Model 2350 Safety Brine Valve Model 1600 brine valve assy Float Assy. (red/white) 60029HW Model 1600 Hot Water brine valve assy SAN San float assy. (Hot Water) Model 1700 brine valve assy.( specify flow control ) FFA Model 2300 safety brine valve Model 1710 brine valve assy.( specify flow control ) FFS Model 2300 Safety brine valve Float Assy. (blue/white) COVERS Float Assy Environmental lower cover Environmental SALES AND SERVICE AIDS Designer 2 piece Spec sheet Designer 1 piece ( only available in black ) Service manual Designer Lower cover Product line Catalog DRIAN LINE FLOW CONTROLS SEAL & SPACER KITS " FNPT x ¾ FNPT ( specify flow control.6-7.0) Upper kit FNPT x 1 FNPT ( specify flow control ) Upper kit, Hot Water FNPT x 1 MNPT ( specify flow control ) Lower kit FNPT x ¾ FNPT ( specify flow control ) Lower kit, Hot Water " FNPT x 1 FNPT ( specify flow control.6-7.0) SERVICE EQUIPMENT CAM ASSEMBLY Seal & Spacer stuffer tool upper Separate time fill drive cam ( Black ) Spacer puller tool lower Lower drive (Designer) Seal & Spacer stuffer tool lower Lower drive (Environmental) Spacer puller tool upper Silicone, 2 oz. Tube 24 HOUR GEAR ASSEMBLY Meter Checker Std. Range Meter Checker Ext. Range Model 3200 timer 2 times regeneration Silicone, 8 lb. pail Model 3200 timer 3 times regeneration Model 3200 timer 4 times regeneration SERVICE VALVE OPERATOR ASSEMBLY ( SVO ) Model 3200 timer 6 times regeneration SVO (Old Style) SVO (New Style) INJECTOR ASSEMBLIES COMPLETE _ ½ brine (specify size of injector) SKIPPER WHEEL ASEMBLIES /8 brine (specify size of injector) Timer 12 day Brass - 3/8 brine ( specify size of injector) Timer 7 day Page 35