Ford Super Duty Rocker Panel Marker Lights F250 4x4 XLT Sport Crew Cab 5.4L
|
|
- Buddy Melton
- 6 years ago
- Views:
Transcription
1 1 of 32 Ford Super Duty Rocker Panel Marker Lights 2004 F250 4x4 XLT Sport Crew Cab 5.4L Back to 2004 F250 Main Page Click Here for a PDF version of this article Since buying my truck 4 years ago, I've done a number of mods & maintenance procedures. Up until this point, all of these were intended to have function over form. For a change, this mod is mostly just for looks! Small amber marker lights mounted to the "pinch weld" below the rocker panel. I purchased six amber marker lights from superbrightleds.com. The M11 series, part number M11PC-A3. They are 2.125" x 1.125".
2 of 32 After doing some measuring, I decided that three lights per side wasn't quite what I was looking for. The spacing just didn't work out with my step brackets and such. So I ordered two more so I could space them a little closer and have four on each side. That seemed more balanced to me. I spent quite a bit of time measuring and I ended up spacing the lights 20 inches apart. Here's a rough sketch of how I spaced them.
3 3 of 32 After measuring several more times, I commenced to drilling. First center punch, then a 1/8" pilot hole, followed by a 1/4" hole. I drilled the holes 9/16" up from the bottom of the pinch weld.
4 4 of 32
5 5 of 32
6 6 of 32 Test fit before drilling the others.
7 7 of 32 The test fit of all four.
8 8 of 32 After the test fit, I removed them all to make up the harness that will connect them all together, and to power & ground. But first, I went around to all the holes and dabbed in a little epoxy black paint.
9 of 32 I use standard crimp connectors for almost all of my wiring projects on this truck. However, I haven't shown any pictures of my "standard procedure" when using these. I always crimp AND solder them. First, strip the wire back about 3/8"
10 0 of 32 Then tin the wire with a bit of solder.
11 11 of 32 Then install and crimp the connector.
12 2 of 32 Then solder the connection. Hold the iron on the opposite side of the connector. You can tell when its hot enough to feed the solder in when you see the surface of the connector "flash" over. Hard to explain but you'll see what I'm talking about the first time you try one.
13 13 of 32 The rest of the harness requires two wires to go into one crimp terminal. Here's the tinned wires.
14 14 of 32 Solder them to each other.
15 15 of 32 Then crimp on the terminal again.
16 16 of 32 Finally, solder it again as described above.
17 7 of 32 Now for the connections. I decided to bring the wiring inside the cab and connect into the parking light circuit in the main loom behind the kick panel. To see the steps for removing the kick panel, check out my courtesy lamps writeup. The brown wire behind the kick panel is the parking light wire. I verified this with my meter. I have a set of insulation piercing probes that I use for this sort of thing.
18 18 of 32
19 19 of 32 Here's 14V with the engine running and the park lights on. The voltage goes to zero with the lights off.
20 20 of 32 Now that the harness is built and the wires have been identified, its time to finish off the install. This drawing depicts how I built the harness for these lights.
21 21 of 32 Mount up the lights.
22 22 of 32 Here's a shot of the wiring from the backside.
23 23 of 32 When I installed my Pop & Lock Tailgate Lock, I drilled a hole through the floor to pass the loom through. I ran the marker light wires through there. Here's the pic of that loom from the tailgate lock writeup.
24 4 of 32 I drilled a similar hole on the passenger side and ran a piece of 3/8" loom through it to get the pass side marker light wires into the cab. There's no equivalent brown wire on the pass side, so I ran a wire behind the dash, across to the drivers side to connect into the marker light circuit. Here's where I tapped into the brown wire. The two upper wire taps are for my power tailgate lock.
25 25 of 32 I attached the ground wire here, just above where I tapped into the brown wire. There is an equivalent ground point on the pass side, so I attached its ground there.
26 26 of 32 Testing them out before completely dressing up the wiring.
27 27 of 32 A few shots of the finished product
28 28 of 32
29 29 of 32
30 30 of 32
31 31 of 32 Finally a night time shot.
32 32 of 32 Questions or Comments?
Ford Super Duty 4x4 CB Antenna Installation 2004 F250 4x4 XLT Sport Back to 2004 F250 Main Page
Ford Super Duty 4x4 CB Antenna Installation 2004 F250 4x4 XLT Sport Back to 2004 F250 Main Page I wanted to install a CB in my truck but I didn't particularly like any of the typical antenna installation
More informationFRAME BRACKET. Doing Our Best to Provide You the Best. Ford. Page 1. BOlT TORQUE SPECIFICATIONS HJ31000,Rev 0
2-13 HJ31000,Rev 0 Ford BOlT TORQUE SPECIFICATIONS METRIC BOlTS Size Grade Torque 8mm 8.8 23 ft/lbs. 10mm 8.8 45 ft/lbs. 12mm 8.8 78 ft/lbs. 14mm 8.8 125 ft/lbs. STANDARD BOlTS Size Grade Torque 5/16 5
More informationInstructions for Lighting an S Scale Caboose
Instructions for Lighting an S Scale Caboose The S Scale Caboose lighting kit is adaptable for most caboose models of rolling stock including American Flyer (TM) and contains the same components as found
More informationINSTALLATION INSTRUCTIONS 3"/4 BENT END SIDEBARS FORD F-150 SUPERCREW PART # DZ /DZ
INSTALLATION INSTRUCTIONS 09-12 FORD F-150 SUPERCREW PART # DZ 372697/DZ 372699 PARTS LIST: 1 Driver/Left Sidebar 4 1/2 Lock Washers 1 Sidebar 4 12mm x 32mm OD x 3mm Flat Washers 1 Driver/Left Mounting
More informationIN 578. Tools Required. Torque Specification: 10mm Socket 7/16 Socket 1/2 Socket 1/2 Wrench 7/16 Wrench 1/8 Allen Wrench.
Tools Required 2011-C Ford F250/F350 No Drilling into Vehicle is Required 10mm Socket 7/16 Socket 1/2 Socket 1/2 Wrench 7/16 Wrench 1/8 Allen Wrench FL277 x 1 Torque Specification: 1/4 Bolts - 6 Ft Lbs.
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions 2004 2008 Ford F-150 XLT, FX4, & Lariat Pre-wired without side signals Pre-wired with side signals Without side directional lights, see page 2 With side directional
More informationFORD #2228. Gross Trailer Weight (Maximum)...24,000 lbs. Vertical Load Weight (Max. Pin Weight)...6,000 lbs. SYSTEM TOW CAPACITY
FORD 24K Industry Standard Rail Heavy Duty Custom Mounting Kit #2228 Gross Trailer Weight (Maximum)...24,000 lbs. Vertical Load Weight (Max. Pin Weight)...6,000 lbs. SYSTEM TOW CAPACITY Please note, in
More informationInstallation Instructions
FORD 20K Industry Standard Rail Custom Mounting Kit #2738 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order to determine
More informationInstallation Instructions
DODGE 16K Industry Standard Rail Custom Mounting Kit #2728 Gross Trailer Weight (Maximum)...16,000 lbs. Vertical Load Weight (Max. Pin Weight)...4,000 lbs. SYSTEM TOW CAPACITY Please note, in order to
More informationInstallation Instructions
DODGE RAM 2500 20K Industry Standard SuperRail Custom Mounting Kit #2336 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note,
More informationFRAME BRACKET. Doing Our Best to Provide You the Best. Ford F /2, 6 1/2 & 8 Boxes. BOlT TORQUE SPECIFICATIONS. 7/17 HJ31001,Rev 3
Ford F150 5 1/2, 6 1/2 & 8 Boxes 7/17 HJ31001,Rev 3 BOlT TORQUE SPECIFICATIONS METRIC BOlTS Size Grade Torque 8mm 8.8 23 ft/lbs. 10mm 8.8 45 ft/lbs. 12mm 8.8 78 ft/lbs. 14mm 8.8 125 ft/lbs. STANDARD BOlTS
More informationBi-Color Signal Mirror Installation Instructions
Bi-Color Signal Mirror Installation Instructions 2005-2009 Toyota Tacoma THE safety accessory of the 21 st Century. P/N 210-0141-0 Rev. A2 (3/30/09), BTV 2007 Muth Mirror Systems, LLC Page 3 of 13PplPage
More informationInstallation Instructions
FORD 20K Industry Standard Rail Custom Mounting Kit #2760 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order to determine
More informationBHT2 Mounting Instructions For Case RB455 (Round Baler )
BHT2 Mounting Instructions For Case RB455 (Round Baler ) General: These instructions address the question of where to mount the BHT2 baler mounted moisture tester sensor pads on the RB455 series round
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions Toyota RAV4 1996-2000 THE safety accessory of the 21 st Century. P/N 210-0034-0 Rev B1 (11-19-02), GG 2002 Muth Co. LLC. Note: Professional Installation Recommended
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions Honda CRV 1997-2003 THE safety accessory of the 21 st Century. P/N 210-0032-0 Rev B2 (6-26-04), GG 2003 Muth Mirror Systems, LLC. Note: Professional Installation
More information2. FOLLOW THE INSTRUCTIONS INCLUDED WITH THE SPECIFIC BRACKET PACKAGE THAT YOU ARE USING, TO MOUNT THE BRACKETS TO YOUR VEHICLE.
INSTALLATION INSTRUCTIONS AND PARTS LIST MODEL: 583098, 583102, 583108, 583114, 583125, 584098, 584102, 584114, 584125 O-MEGA II 6 OVAL STEPS UNIVERSAL APPLICATION 1. READ INSTRUCTIONS COMPLETELY AND CHECK
More informationInstallation Instructions
TOYOTA 16K Industry Standard Rail Custom Mounting Kit #2748 Gross Trailer Weight (Maximum)...16,000 lbs. Vertical Load Weight (Max. Pin Weight)...4,000 lbs. SYSTEM TOW CAPACITY Please note, in order to
More informationIMPORTANT! Recommended Tools. 7/16 Deep socket Phillips screwdriver
IMPORTANT! Read all instructions carefully before commencing any work. Always wear proper safety equipment. Some installation steps will require two or more installers. Recommended Tools Ratchet 10-mm
More informationTech Sheet. T4 Interior conversion kit how to - fitting instructions. 1. Rear seat belts. 2.
Page 1 of 8 T4 Interior conversion kit how to - fitting instructions Thank you for purchasing our T4 interior conversion kit. This kit will enable you to convert any SWB left hand loading door T4 into
More informationUniden CB Radio PRO 510XL (87-18 Wrangler YJ, TJ, JK & JL)
Installation Time: 60-90 Minutes Tools Required: Phillips Screw Driver Drill (with drill bit set) Multimeter Tester Electrician s Stripper/Cutter Uniden CB Radio PRO 510XL (87-18 Wrangler YJ, TJ, JK &
More informationInstallation Instructions
CHEVY / GMC 24K Industry Standard Rail Heavy Duty Custom Mounting Kit #2226 Gross Trailer Weight (Maximum)...24,000 lbs. Vertical Load Weight (Max. Pin Weight)...6,000 lbs. SYSTEM TOW CAPACITY Please note,
More informationBPF Toyota Tundra Mesh Installation Guide
BPF 2007-2009 Toyota Tundra Mesh Installation Guide www.bpfabricating.com Tools Required Philips Screw Driver Flat Head Screw Driver Dremel or Rotary Tool Hand Saw or Multi Max Adjustable Square Tape Measure
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationINSTALLATION INSTRUCTIONS SIDE BAR FORD ESCAPE & MAZDA TRIBUTE PART #
INSTALLATION INSTRUCTIONS SIDE BAR 2008-2010 FORD ESCAPE & MAZDA TRIBUTE PART # 50136 50137 PARTS LIST: 1 Driver/Left Sidebar 2 10-1.50mm x 35mm Bolt Plate 1 Passenger/Right Sidebar 2 10-1.50mm x 30mm
More informationPICKUP TRUCK INSTALLATION INSTRUCTIONS
Qty. Description PARTS LIST 2 Side Box 1 Main Drawer 1 Drawer Deck 2 48 Track 2 24 Track 22 ¾" - #10 Pan Head Sheet Metal Screw 2 ½ - #10 Pan Head Sheet Metal Screw 4 ½ - #10-24 Flat Head Machine Screw
More informationINSPECTION AND CORRECTION OF BELLHOUSING TO CRANKSHAFT ALIGNMENT
INSPECTION AND CORRECTION OF BELLHOUSING TO CRANKSHAFT ALIGNMENT BACKGROUND Proper alignment of the transmission input shaft to the crankshaft centerline is required in order to achieve the best results
More informationFutura and Caponord dash repair
Futura and Caponord dash repair So... Most of us know about the issues that some have had with their instrument cluster going deal. Some have had it happen while riding while others have had it happen
More informationNo crimping is required just solder the the wire to the crimp piece and use some heat shrink tubing to cover the end of the crimp.
In this section we will be wiring up the IEC socket (AC plug) with the rocker switch and the Mains transformer primaries. Follow these instructions if you live in an area with 100, 110, 220 or 230 Volts!"
More informationInstallation Instructions
CHEVY / GMC 20K Industry Standard Rail Custom Mounting Kit #2724 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order
More informationInstallation Instructions
CHEVY / GMC 16K Industry Standard Rail Custom Mounting Kit #2730 Gross Trailer Weight (Maximum)...16,000 lbs. Vertical Load Weight (Max. Pin Weight)...4,000 lbs. SYSTEM TOW CAPACITY Please note, in order
More information66 Dodge Charger (and others) Tach board
66 Dodge Charger (and others) Tach board Introduction: This board replaces the original tachometer driver board in the 66 charger and other cars that use electronics external to the tachometer. The board
More informationACCESS COVER INSTALLATION INSTRUCTIONS (Kit #601 for 2006 Honda Ridgeline)
ACCESS COVER INSTALLATION INSTRUCTIONS (Kit #601 for 2006 Honda Ridgeline) NOTE TO INSTALLER: IMPORTANT READ BEFORE ATTEMPTING INSTALLATION. Allow extra time, up to 2 hours to install this cover. Disassembly
More informationCHEVY 4100/4400 SUPERRAIL MOUNTING KIT WITH ADAPTER FOR B&W GOOSENECK PART #4434
CHEVY 4100/4400 SUPERRAIL MOUNTING KIT WITH ADAPTER FOR B&W GOOSENECK PART #4434 Installation Instructions SPECIFICATIONS Fits 1999-2010 Chevy 2500 & 3500 Short Bed Mounts to B&W gooseneck part #1067 Hitch
More informationCHEVY 4100/4400 SUPERRAIL MOUNTING KIT WITH ADAPTER FOR B&W GOOSENECK PART #4432
CHEVY 4100/4400 SUPERRAIL MOUNTING KIT WITH ADAPTER FOR B&W GOOSENECK PART #4432 Installation Instructions SPECIFICATIONS Fits 2011-2018 Chevy 2500 & 3500 Short Bed Mounts to B&W gooseneck part #1011 Hitch
More informationELECTRICAL WIRING SOLDERING AND CRIMPING Article No. REPAIRS SERVICE TIPS
ELECTRICAL WIRING SOLDERING AND CRIMPING Article No. REPAIRS SERVICE TIPS 03-11-6 FORD: LINCOLN: MERCURY: 1997 PROBE, THUNDERBIRD 1997-2000 CONTOUR 1997-2002 ESCORT 1997-2003 CROWN VICTORIA, MUSTANG, TAURUS
More informationFRAME BRACKET Chevy Silverado 1500 & GMC Sierra /2 & 6-1/2 Box
, Rev 1 01/19 FRAME BRACKET 8551011 Chevy Silverado 1500 & GMC Sierra 1500 5-1/2 & 6-1/2 Box ITEM PART # QTY DESCRIPTION 1 10379 8 1/2" UNC FLANGED NUT 2 14266 8 BOLT,.50 NC X 1.75 GR5 HEX W/ KNURLED NECK
More informationBefore returning this product to the store of purchase
Before returning this product to the store of purchase Contact Dee Zee if you experience the following problems: Missing Parts Installation Problems/Questions Warranty Questions 1.800.779.2102 Hours of
More informationBushwacker Jeep Flat Style Fender Flares Front Pair
Bushwacker Jeep Flat Style Fender Flares Front Pair Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Installation Time: 3-4 Hours Tools Required:
More informationInstallation Manual MODEL AE-46
Installation Manual MODEL AE-46 GET TO KNOW YOUR UNIT (BOTTOM OF RACEWAY) 2 5 1 4 6 3 1. CROSS BRACES 2. ELECTRICAL RACEWAY 3. SIDE BRACKETS 4. ELECTRICAL CORD COVER 5. ELECTRICAL OUTLET 6. HOT IRON REST
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS R5 STEP BOARD APPLICATION: 2009-2017 Dodge Ram 1500 Quad / Crew Cab 2010-2017 Dodge Ram 2500/3500 Crew Cab PART NUMBER: 28-51040, 28-51045, 28-51050, 28-51055 ITEM QUANTITY DESCRIPTION
More informationTrim down the piece of casting being pointed to with the tip of the pencil in the first picture. It is only the 'inboard casting that needs to be
1. File off the moulding pips from the wheel flanges. File the ends of the tube smooth and de-burr. Assemble the wheel sets with a drop of car engine oil on the axles. Glue the wheel sets into place. 2.
More informationInstallation Instructions
CHEVY / GMC 20K Industry Standard Rail Custom Mounting Kit #2724 Gross Trailer Weight (Maximum)...20,000 lbs. Vertical Load Weight (Max. Pin Weight)...5,000 lbs. SYSTEM TOW CAPACITY Please note, in order
More informationInstallation tutorial for Console Customs Xbox ONE MaxFire ONE V2 PCB
Installation tutorial for Console Customs Xbox ONE MaxFire ONE V2 PCB This tutorial is designed to aid you in installation of a console customs MaxFire ONE V2 Circuit board in the newer Xbox One Controllers
More informationInstallation for Full Size Polaris Ranger Crew Doors
Installation for Full Size Polaris Ranger Crew Doors Order of Installation: Heater Doors Wiper on to Windshield Windshield Top & Back Panel Note: Most of the steps in these instructions need to be repeated
More informationFurness Railway Wagon Co. Glasgow & South Western Railway/LMS/BR ton Box Van Steel Under-Frame
Furness Railway Wagon Co. Glasgow & South Western Railway/LMS/BR 1920 10ton Box Van Steel Under-Frame Wheels, paint and transfers required to complete. Please note that to aid the folding of the various
More information2012 Fleetwood Discovery 40X Interior Tac Light Installation Description: LT-INT 12V TAC 3/8 X 28 Part Number
2012 Fleetwood Discovery 40X Interior Tac Light Installation Description: LT-INT 12V TAC 3/8 X 28 Part Number 592515 Note: Safety First: Always Disconnect the AC and DC Power when working with or around
More informationKwik-Lock. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.
Serving the Truck & Trailer Industry Since 1944 Installation Instructions Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 800-535-9545 www.aeroindustries.com
More information05-17 Mustang Fuel System Wire Upgrade Installation
PARTS LIST: -10AWG INLINE FUSE HOLDER WITH 30AMP BLADE FUSE -16FT 10AWG HIGH CURRENT PRIMARY WIRE -40AMP AUTOMOTIVE RELAY -1FT 10AWG GROUND WIRE -1FT 10AWG HIGH CURRENT PRIMARY WIRE OUTPUT TO FPDM -1FT
More informationWildcat XX Stage 1 Audio Kit
2436-466 Wildcat XX Stage 1 Audio Kit WARRANTY INFORMATION: All SSV Works enclosures are covered by a limited lifetime warranty against defects in material or workmanship. All SSV Works Electronics are
More informationTOYOTA TACOMA BED EXTENDER Preparation. Part Number: PT General Applicability All 2012 and newer Tacoma models
Preparation Part Number: PT392-35120 Kit Contents 1 1 Curved Tube Assembly - Right 2 1 Curved Tube Assembly - Left 3 3 Center Tube 4 1 Hardware Bag 5 1 Installation Instructions 6 1 Care Card Hardware
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions Ford Explorer 1996-2001, Ford Explorer SportTrac 2001, Ford Ranger 1996-2001, Mazda B-2500\B-3000\B-4000 1998-2001, Mercury Mountaineer 1997-2001 THE safety accessory
More informationFirst I test the resistor to make sure it doesn't fluctuate all over the place. So long as it sits stable between 506 and 560 ohms you are set.
ENET CABLE BUILD These are my instructions for putting together an Ethernet to OBD2 cable to change features on your F-Series vehicle using E-Sys, Toolset32, ISTA P/D or other BMW programming tool. You
More informationGENUINE PARTS INSTALLATION INSTRUCTIONS
GENUINE PARTS INSTALLATION INSTRUCTIONS DESCRIPTION: APPLICATION: PART NUMBER: Interior Accent Light (Multi-color) MURANO, MURANO CROSS CABRIOLET(2011) Interior Accent Light (Multi-color) (B64D0 1SX0A)
More informationInstalling a genuine HoodLift on a Jeep TJ
Installing a genuine HoodLift on a Jeep TJ 1997-2006 To print a full-color version of these instructions go to www.hoodlift.com/products.html. Scroll down to the TJ HoodLift and click on the TJ HoodLift
More informationFILE // 4 GAUGE TERMINAL CONNECTORS DOCUMENT
04 July, 2018 FILE // 4 GAUGE TERMINAL CONNECTORS DOCUMENT Document Filetype: PDF 293 KB 0 FILE // 4 GAUGE TERMINAL CONNECTORS DOCUMENT Alibaba.com offers 124 4 gauge wire connectors products. Unique Bargains
More informationRBP-1215B-RX DODGE RAM QUAD CAB RX3
RBP-1215B-RX3 2002-2017 DODGE RAM 15-3500 QUAD CAB RX3 Passenger side RX-3 Side Step Drill Template Passenger side rear Modular Bracket (6) L Support Brackets Driver side rear Modular Bracket Driver side
More informationTable Saw Disc Sander
instructables Table Saw Disc Sander by tomatoskins A disc sander is a must for any shop! They make quick work of shaping and smoothing stock. Getting the most out of your shop tools can often take you
More informationTOYOTA TACOMA LED BED LIGHTS Preparation
Preparation Part Number: PT948-35160 Kit Contents Item # Quantity Reqd. Description 1 1 Hardware Kit 2 1 Driver Side LED assembly 3 1 Passenger Side LED assembly 4 1 Main Wire Harness Hardware Bag Contents
More informationPowerLock. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.
Serving the Truck & Trailer Industry Since 1944 FOR Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 800-535-9545 www.aeroindustries.com Indianapolis,
More information10-1.5mm x 40mm Hex Bolt 1 Driver/Left Front Inner Support Bracket (2WD & 4WD Vehicles W/O Skid Plate Only) 2
PARTS LIST: 3" ROUND SIDEBARS 1 Driver/Left sidebar 4 12mm x 32mm OD x 3mm Flat Washer 1 Passenger/Right sidebar 4 12mm x 24mm OD x 2.5mm Flat Washer 1 Driver/Left Mounting Bracket 6 12mm Lock Washers
More informationSignal Mirror Installation Instructions Honda Odyssey
Signal Mirror Installation Instructions 2005-2009 Honda Odyssey THE safety accessory of the 21st Century. P/N 210-0122-0 Rev. A4 (6/9/09), BTV 2006 Muth Company, LLC PROFESSIONAL INSTALLATION RECOMMENDED
More informationMETRIC BOlTS. Size Grade Torque 8mm ft/lbs. 10mm ft/lbs. 12mm ft/lbs. 14mm ft/lbs. 16mm ft/lbs.
8/16 HJ31005,Rev 7 BOlT TORQUE SPECIfICATIONS METRIC BOlTS STANDARD BOlTS Size Grade Torque 5/16 5 18 ft/lbs. 3/8 5 30 ft/lbs. 7/16 5 50 ft/lbs. 1/2 5 75 ft/lbs. 5/8 5 150 ft/lbs. 3/4 5 290 ft/lbs. Size
More informationFord Mustang, SVT, Cobra
1996 2004 Ford Mustang, SVT, Cobra N2MB WOT Box Installation Instructions NOTE: If you have a CDI (capacitive discharge ignition system) please contact us at support@n2mb.com for additional instructions.
More informationToyota Tacoma SliderStep Installation Fits 05 and later Tacoma Double and Extra Cab Pickup Trucks
Toyota Tacoma SliderStep Installation Fits 05 and later Tacoma Double and Extra Cab Pickup Trucks NOTE: The Step Plate (piece with Slee Logo) is now a bolt on piece that gets added when sliders are installed.
More informationTOOL LIST FOR TAILGATE HIDDEN LATCH & LINK ASSY FOR FORD FLARESIDE TRUCKS
TOOL LIST FOR TAILGATE HIDDEN LATCH & LINK ASSY FOR 53-87 FORD FLARESIDE TRUCKS Vise Grip Clamps C-clamps Sharpie Marker Ball Peen Hammer Center Punch 3/8 or 1/2 Drill 5/32, 7/32, 9/32, and 3/8 Drill Bits
More informationINDEPENDENT FRONT SUSPENSION SWAP
INDEPENDENT FRONT SUSPENSION SWAP 20 PHOTOS In this article we will show how to change out the old frame/front suspension of your 49, 50, and 51 Mercury / Ford to a new IFS unit. This high tech front suspension
More informationINSTALLATION INSTRUCTIONS AND PARTS LIST MODEL , O-MEGA II 6 OVAL STEPS
INSTALLATION INSTRUCTIONS AND PARTS LIST MODEL 583036, 584036 O-MEGA II 6 OVAL STEPS 1. READ INSTRUCTIONS COMPLETELY AND CHECK TO MAKE SURE THAT ALL REQUIRED PARTS (LISTED ON THE SERVICE PARTS LIST) ARE
More informationDual Fidgety Art Bot. We enjoyed building our Trashy Art Bot just as much as our Fidgety Art Bot.
Dual Fidgety Art Bot Our instructions will take you through the step by step procedure to build a Dual Fidgety Art Bot, an Art Bot built with two fidget spinners stacked together. Since our investigation
More informationFORD 4100/4400 SUPERRAIL MOUNTING KIT WITH ADAPTER FOR B&W GOOSENECK PART #4431
FORD 4100/4400 SUPERRAIL MOUNTING KIT WITH ADAPTER FOR B&W GOOSENECK PART #4431 Installation Instructions SPECIFICATIONS Fits 1999 2016 Ford F250 & F350 Short Bed Mounts to B&W gooseneck part #1108 & 1111
More informationLoD Offroad. Jeep JK 2 Door Sliders Installation Instructions
LoD Offroad Jeep JK 2 Door Sliders Installation Instructions 1. To remove either the Jeep JK Wrangler Unlimited Rubicon rocker guards or Sahara running boards, use a 10mm wrench to remove the 3 pairs of
More informationPlease read the instructions completely BEFORE starting this project.
Please read the instructions completely BEFORE starting this project. Rhodes Race Cars 10 Point Roll Cages are not designed for use in vehicles where the stock floor has been removed. Check your sanctioning
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions 2006 2007 Honda Ridgeline THE safety accessory of the 21 st Century. P/N 210 0142 0 Rev. A (9/5/07), BTV 2007 Muth Company, LLC Professional Installation Recommended:
More informationOPEN FENDER MANUAL Installation Instructions Open Fender System Product Number: TF4100/TF4110 Application: 2017 FORD F250/350
OPEN FENDER MANUAL 2018 Installation Instructions Open Fender System Product Number: TF4100/TF4110 Application: 2017 FORD F250/350 SAFETY Your safety and the safety of others is very important. In order
More informationSignal Mirror Installation Instructions Dodge Charger, Dodge Magnum, Chrysler 300
Signal Mirror Installation Instructions 2006-2009 Dodge Charger, 2005-2008 Dodge Magnum, 2005-2009 Chrysler 300 THE safety accessory of the 21st Century. P/N 210-0123-0 Rev. A4 (10/7/09), BTV 2007 Muth
More informationPowerLock. Installation Instructions. Attention Dealers: Please give this owners manual to the customer when the product is delivered.
Serving the Truck & Trailer Industry Since 1944 FOR Attention Dealers: Please give this owners manual to the customer when the product is delivered. Call 800-535-9545 www.aeroindustries.com Indianapolis,
More information(6) Plastic Retainers. Passenger/Right. Passenger/Right Support Brackets
PART#R102580 PARTS LIST: 1 Driver/Left HD Running Board 4 8mm Bolt/Nut Plates 1 Passenger/Right HD Running Board 4 8mm Plastic Retainers 2 Driver/Left & Center Mount Bracket 14 8mm-1.25 x 30mm Hex Bolts
More informationWiring the 1176LN Clone
Back to Main 1176 Page 15 October 2004 modified 9 January 2005 revised 31 January 2006 Wiring the 1176LN Clone Keeping the Hum to a Minimum There's a feeling of satisfaction you get when you finish stuffing
More informationInstallation Instructions
DODGE 4100/4400 SUPERRAIL MOUNTING KIT WITH ADAPTER FOR B&W GOOSENECK PART #4433 Installation Instructions SPECIFICATIONS Fits 2003 2012 Dodge 2500 & 3500 Short Bed Mounts to B&W gooseneck part #1307 &
More informationSignal Mirror Installation Instructions
Signal Mirror Installation Instructions 2005-2010 Chevy Corvette C6 THE safety accessory of the 21 st Century. P/N 210-0144-0 Rev. A3 (9/29/2011), BTV 2007 Muth Mirror Systems, LLC Page 3 of 10PplPage
More informationSTART HERE BEFORE YOU BEGIN FIG 1 STEP 2
PROFESSIONAL INSTALL RECOMMENDED REAR MODULAR / MULTI LED ROOF MOUNTS PART#: Z350040 / Z350050 REAR ROOF LED LIGHT MOUNTS Parts included (1) - Driver Side Roof Mount Upright (1) - Passenger Side Roof Mount
More informationUS RACK, Inc Falcon Drive, Madera, CA
US RACK, Inc - 2850 Falcon Drive, Madera, CA 93637-559-661-3050 INSTALLATION AND USE INSTRUCTIONS for Long-John Extension Ladder Rack WARNING: Do NOT attempt to install or use this rack without following
More informationRough Country JK Modular Winch Mount Bumper With Light End Caps
Rough Country JK Modular Winch Mount Bumper With Light End Caps Note: These instructions involve cutting parts of your vehicle. Please read all instructions prior to starting. Note: This installation also
More informationPLEASE READ INSTRUCTIONS THOROUGHLY BEFORE PROCEEDING
Part No. 8870 -or Part No. 9100-9110 Front Fender Flares Flat Panel Design 07-09 Jeep JK, 2/4 Dr. PLEASE READ INSTRUCTIONS THOROUGHLY BEFORE PROCEEDING We have provided complete instructions and specific
More informationINSTALLATION INSTRUCTIONS
TEL:1-866-XANATOS INSTALLATION INSTRUCTIONS PART # RN-FOF1SCC-09-91 CUTLASS RUNNING BOARDS PARTS LIST: 5 STAINLESS AND ALUMINUM SIDEBARS 2 Left or right Sidebars 10 8-1.25mm x 30mm Hex Bolts 2 Driver/Left
More informationX5 License Plate PDC Retrofit (Part # ) dkl
X5 License Plate PDC Retrofit (Part # 66 21 0 416 597) dkl Disclaimer: This article is only intended to be use as a guideline in addition to those instructions provided by BMW. As with all modifications,
More informationSplice-In Sequential Tail Lights Installation Guide (96-04)
Splice-In Sequential Tail Lights Installation Guide (96-04) The below installation instructions work for the following products: Mustang Sequential Taillights Kit - Splice-in (96-04) Please read through
More informationInstall The Trailer Lighting Wire Harness Connector
Install The Trailer Lighting Wire Harness Connector This is probably the toughest part of the whole trailer hitch install. It helps to have a little background in electronics, but if you don't then simply
More informationINSTRUCTIONS INSTRUCCIONES CONSIGNES
PPLICTION: 2003-15 1500/2500/3500 HD SILVERDO/SIERR EXTENDED C/DOULE C/CREW C INCLUDING DIESEL EQUIPPED & 03-0 CLSSIC MODELS PRT # 5-5165, 5-5155 HDX RUNNING ORDS UTOMOTIVE PRODUCTS, INC. 1 INSTRUCTIONS
More informationHigh Intensity Colored LED Light Emitter - 12, 3-Watt LEDs VDC - IP Lumens
High Intensity Colored LED Light Emitter - 12, 3-Watt LEDs - 9-32VDC - IP68-2736 Lumens Part #: LEDP3W-12X2C Page: 1 Buy American Compliant The LEDP3W-12X2C LED Light Bar offers high output colored light
More informationSEAT-831. Seat Box Kit. Club Car Precedent. Installation Instructions
SEAT-831 Seat Box Kit Club Car Precedent Installation Instructions Contents of SEAT-831 Seat Box Kit: a (1 ea.) Seat Box Platform b (1 ea.) Front Seat Box Plate c (1 ea.) Foot Plate d (1 ea.) Tailgate
More informationDO NOT EXCEED LOWER OF TOWING VEHICLE MANUFACTURER'S RATINGS OR THOSE LISTED BELOW:
CATALOG NO. 40050 INSTALLATION INSTRUCTIONS NOTE: CHECK HITCH FREQUENTLY, MAKING SURE ALL FASTENERS AND BALL ARE PROPERLY TIGHTENED. A HITCH OR BALL WHICH HAS BEEN DAMAGED SHOULD BE REMOVED AND REPLACED.
More informationElectrical - Wiring Soldering/Crimping Service Tips
TSB 05-18-7 09/22/05 22 septembre 2005 - Wiring Soldering and Crimping Repairs - Service Tips WIRING SOLDERING AND CRIMPING REPAIRS FORD: 2000-2006 Crown Victoria, Focus, Mustang, Taurus 2002-2005 Thunderbird
More informationSignal Mirror Installation Instructions Toyota Tacoma
Signal Mirror Installation Instructions 2005-2015 Toyota Tacoma THE safety accessory of the 21 st Century. P/N 210-0115-0 Rev. A4 (3/11/15), BTV 2005 Muth Mirror Systems, LLC Page 3 of 12PplPage 3 of 12
More informationINSTALLATION INSTRUCTIONS 6 OVAL BENT END SIDEBARS DODGE RAM 1500, CREW CAB PART#: /241533B
PARTS LIST: 1 Driver/Left Sidebar 24 8mm x 24mm x 2mm Flat Washers 1 Passenger/Right Sidebar 12 8mm Lock Washers 3 Driver/left, Passenger Center and Rear 6 8mm Hex Nuts 3 INSTALLATION INSTRUCTIONS 6 OVAL
More informationPassenger/Right Center and Rear Support Brackets. Driver/Left Center and
PARTS LIST: 1 Driver/Left HD Running Board 24 8mm x 24mm OD x 2mm Flat Washers 1 Passenger/Right HD Running Board 12 s 3 Driver/Left front, passenger center/rear Support Brackets 6 8mm-1.25 Hex Nuts 3
More informationframe bracket Dodge x 2 & 4 x 4 (6-1/2 & 8 Boxes Includes Mega Cab)
, Rev 4 02/19 frame bracket 8552026 Dodge 3500 4 x 2 & 4 x 4 (6-1/2 & 8 Boxes Includes Mega Cab) 14 5 7 2 4 11 9 10 17 3 6 1 8 13 15 16 18 12 ITEM PART # DESCRIPTION QTY. 1 00085.50 FLAT WASHER 10 2 00248
More informationApplications: Section 1: Getting Started Tools Needed: BEFORE
Installation of KBD Body Kits Porsche GT 3 Look/Style 2 Piece Polyurethane Front Bumper & Lip Applications: Porsche 996: 1999-2001 Porsche Boxster 986: 1997-2004 Page 1 Tools Needed: Philips Head Screwdriver
More informationE2500 Antenna Installation Instructions:
Thank you for purchasing the Antenna Mod Kit for your Linksys router. First we will show you how to install the antennas for your router. We will also provide you with a tool that will help test the performance
More information67-72 GM SHORT FLEETSIDE STEEL FLOOR TO WOOD FLOOR CONVERSION PART LIST: REQUIRED FOR CONVERSION DESCRIPTION
JAZ:instructions\instruct\67-72conv.pm6 pg 1 67-72 GM SHORT FLEETSIDE STEEL FLOOR TO WOOD FLOOR CONVERSION PART LIST: REQUIRED FOR CONVERSION QTY DESCRIPTION 1 Set Bed Strips 1 Set Bed Wood 1 Each Bed
More information