Polarized Filter Set for your Microscope for under $75.00

Size: px

Start display at page:

Download "Polarized Filter Set for your Microscope for under $75.00"

Barrie Perkins
6 years ago
Views:

1 Polarized Filter Set for your Microscope for under $75.00 ***Every Gemological Microscope should have a Polarized Filter Set Attachment!!!*** What you will need: 2 55mm Polarized Filters 1 Pack of Self-Adhesive Velcro Strips 1-Inch Wide x 3-Inches Long You can go to Best Buy or a camera store and purchase Two (2) 55mm Camera Lens Polarizing Filters Your cost $15.00 to $30.00 Each. You can go to Office Depot or Office Max and purchase a small pack of 1-Inch Wide x 3-Inches Long of Self-Adhesive Velcro Strips. Estimated Time of Assembly: 10 to 15 Minutes Just follow the simple instructions or the photographs. It is that easy!!! #1. First pull the Velcro strips apart and use the harder Nylon Hook strip. #2. Cut a 1-Inch wide by approximately ½-Inch to ¾-Inch long piece of the Harder Nylon Hooked part of the Velcro strip. Cut Two (2) pieces same wide & length. #3. Remove the self-adhesive backing and mount the strip on each side of your microscope Optical head near the bottom of the head closest to the objective lens. Page 1 of 23

2 Notice the White Velcro Backing near the bottom of the Optical Head Apply Stiff Nylon Hook Part of Velcro on both sides of the Optical Head Page 2 of 23

3 Close-Up View of the Stiff Nylon Hook part of the Velcro attached to the Optical Head Page 3 of 23

Apply Stiff Nylon Hook part of Velcro backing on opposite side of the Polarizing Filter as

portion of the Velcro of the Polarizing Filter as seen in the photo ***SPECIAL NOTE*** DO NOT

Notice both sides are fixed and the Velcro Soft / Fuzzy Strips are attached to the Polarizing

4 Apply Stiff Nylon Hook part of Velcro backing on opposite side of the Polarizing Filter as show in the photo The Fussy Soft part of the Velcro is then attached to the Stiff Nylon Hook portion of the Velcro of the Polarizing Filter as seen in the photo ***SPECIAL NOTE*** DO NOT REMOVE ADHESIVE BACKING on the Soft Fuzzy portion of the Velcro strips. Notice both sides are fixed and the Velcro Soft / Fuzzy Strips are attached to the Polarizing Filter ***SPECIAL NOTE*** DO NOT REMOVE ADHESIVE BACKING on the Soft Fuzzy portion of the Velcro strips. Page 4 of 23

5 Notice that One (1) Side of the Filter is now attached to the Optical Head of the Microscope Page 5 of 23

6 Notice the Polarizing Filter is just about to be attached to the opposite side of the microscope with the Velcro strip Page 6 of 23

7 Notice that the Polarizing Filter is now correctly attached to the optical head of the microscope You are more than halfway finish with this simple easy project Page 7 of 23

8 Place the Second Polarizing Filter over the Light Well of Your Microscope as seen in photo You will want to make sure your microscope is vertical in the full and up-right position Page 8 of 23

9 This is a photo of my Older Mark V Bausch & Lomb Gemolite Microscope set up Page 9 of 23

10 Once again MY Old Trusty Gemolite Mark V B&L Microscope Page 10 of 23

11 ***SPECIAL NOTE*** If you want you can also use the extra Velcro and you can attach the bottom filter in place so you can tilt and use your microscope at various angles of tilt if you want. ***SPECIAL Operational Notes**** NEVER USE THE Focus Knob on the Microscope when trying to view the strain pattern in a diamond It is easier to tilt & turn your microscope mounted tweezers You will be wasting time and chasing your tail if you constantly try to refocus your microscope using the focusing knob when looking at and viewing strain within the diamond. Not until you get use to how to find and observe the strain pattern then you can fine turn the focus using the main focusing knob on the microscope especially if you are taking photomicrographs then small adjustments are quick and easy. Page 11 of 23

12 ***SPECIAL NOTE*** Pre-Focus your microscope so that focus is approximately on the tweezers almost parallel to the work platform. You will also want to first start at low magnification to find the strain pattern then increase power setting to desired strength. Page 12 of 23

13 A Polarized Microscope Set-up is ONE of the Most Important Features NEEDED TODAY!!!! This is ONE of the MAIN Observational Tools needed to help Identify Natural vs. Synthetic Diamond ***SPECIAL NOTE*** This article DOES NOT teach or train how to Identify Natural vs. Synthetic Diamond You will also need to take a Special Advanced Hand-On Class Room Training Session to help aid you in what to look for as far as Clues that you will observe that will instantly raise the Red Warning Flags to caution you to slow down and think things through before opening your mouth and making a statement you might regret later on. ***SPECIAL RESOURCE MANUALS*** YOU WILL WANT TO PURCHASE and READ COVER-to-COVER*** ***Laboratory-Grown Diamonds Informational Guide to HPHT-grown and CVD-grown Diamonds Second (2 nd Edition) By Branko Deljanin & Dusan Simic ***Natural or Synthetic Diamond Identifying with CPF, DF and UV Light By Dusan Simic Analytical Gemology & Jewellery For more information on Analytical Gemology and Jewelry call (917) ***Identifying Diamond Types and Synthetic Diamonds with CPF (Cross Polarized Filters) Second (2 nd Edition) By Dusan Simic Analytical Gemology & Jewellery For more information on Analytical Gemology and Jewelry call (917) The above Three (3) Manuals are a MUST READ for every gemologist and gem & Jewelry appraiser!!! Page 13 of 23

14 Page 14 of 23

15 Page 15 of 23

16 Page 16 of 23

17 Page 17 of 23

18 Page 18 of 23

19 Page 19 of 23

20 Page 20 of 23

21 Page 21 of 23

22 Page 22 of 23

23 Page 23 of 23

Photographic Documentation Systematic Collection of Photographic Evidence for Appraising Gems & Jewelry

Photographic Documentation Systematic Collection of for Appraising Gems & Jewelry With the advent of moderately priced high quality high resolution digital cameras it is now cost effective for Gem & Jewelry