WEST HOLLYWOOD ACCESSIBLE UNISEX BATHROOMS: COMMERCIAL CLEARANCES. Accessible Unisex Bathrooms: Commercial Page 1 of 5
|
|
|
- Kelley Jordan
- 5 years ago
- Views:
Transcription
1 Page 1 of 5 When toilet rooms are provided, each toilet room shall comply with Section 11B of the California Building Code. Unisex toilet rooms (Single-use or family) shall contain not more than one lavatory, and not more than two water closets without urinals or one water closet and one urinal. Doors to unisex toilet rooms and unisex bathing rooms shall have privacy latches. (CBC Section 11B ) CLEARANCES Clearances. Clearances shall comply with Section 11B Turning spaces. Turning space complying with Section 11B or 11B shall be provided within the room. (CBC Section 11B , 11B-304.3) Circular space. The turning space shall be a space of 60 inches (1524 mm) diameter minimum (Fig. 1(a)). The space shall be permitted to include knee and toe clearance complying with Section 11B-306. (CBC Section 11B , 11B ) T-Shaped space. The turning space shall be a T- shaped space within a 60 inch (1524mm) square minimum with arms and base 36 inches (914 mm) wide minimum. Each arm of the T shall be clear of obstructions 12 inches (305mm) minimum in each dir3ection and the base shall be clear of obstructions 24 inches (610mm) minimum (Fig. 1(b)). The space shall be permitted to include knee and tow clearance complying with Section 11B-306 only at the end of either the base or one arm. (CBC Section 11B ) Overlap. Required clear floor spaces, clearance at fixtures, and turning space shall be permitted to overlap. (CBC Section 11B ) Door swings. Doors shall not swing into the clear floor space or clearance required for any fixture. Other than the door to the accessible water closet compartment, a door in any position, may encroach into the turning space by 12 inches (305mm) (CBC Section 11B ) min arm arm (a) Circular Space 24 min 12 min base 36 min (b) T-Shaped Space 12 min Figure 1 a & b Wheelchair Turning Space
2 Page 2 of 5 WATER CLOSETS Water closets. Where water closets are provided, at least one shall comply with Section 11B-604 (Fig. 2). (CBC Section 11B ) Location. The water closet shall be positioned with a wall or partition to the rear and to one side. The center-line of the water closet shall be 17 inches (432mm) minimum to 18 inches (457mm) maximum from the side wall or partition. Water closets shall be arranged for a left-hand or right-hand approach. (CBC Section 11B-604.2) Size. Clearance around a water closet shall be 60 inches (1524mm) minimum measured perpendicular from the side wall and 56 inches (1422mm) minimum measured perpendicular from the rear wall. A minimum 60 inches (1524mm) wide and 48 inches (1219mm) deep maneuvering space shall be provided in front of the water closet (Fig.2). (CBC Section 11B ) Seats. The seat height of a water closet above the finish floor shall be 17 inches (432mm) minimum and 19 inches (483mm) maximum measured to the top of the seat. Seats shall not be sprung to return to a lifted position. Seats shall be 2 inches (51mm) high (CBC Section 11B-604.4) Flush controls. Flush controls shall be hand operated or automatic. Hand operated flush controls shall comply with Section 11B-309 except they shall be located 44 inches (1118mm) maximum above the floor. Flush controls shall be located on the open side of the water closet. (CBC Section 11B-604.6) Overlap. The Required Clearance around the water closet shall be permitted to overlap the water closet, associated grab bars, dispensers, sanitary napkin disposal units, coat hooks, shelves, accessible routes, clear floor space and clearances required at other fixtures, and the turning space. No fixtures or obstructions shall be located within the water closet clearance. (CBC Section 11B ) 56 Figure 2 Size of Clearance at Water Closets (CBC Figure 11B ) Figure 3 Typical Water Closet Dimensions (Configuration may vary)
3 Page 3 of 5 GRAB BARS Grab bars. Grab bars for water closets shall comply with Section 11B-609. Grab bars shall be provided on the side wall closet to the water closet and on the rear wall. Where separate grab bars are required on adjacent walls at a common mounting height, an L- shaped grab bar meeting the dimensional requirements of Section 11B and 11B shall be permitted. (CBC Section 11B-604.5) Circular cross section. Grab bars with circular cross sections shall have an outside diameter of 1 ¼ inches (32mm) minimum and 2 inches (51mm) (CBC Section 11B ) Non-circular cross section. Grab bars with noncircular cross sections shall have a cross-section dimension of 2 inches (51mm) maximum and a perimeter dimension of 4 inches (102mm) minimum and 4.8 inches (122mm) (CBC Section 11B ) Spacing. The space between the wall and the grab wall shall be 1 ½ inches (38 mm). The space between the grab bar and projecting objects below and at the ends shall be 1 ½ inches (38mm) minimum. The space between the grab bar and projecting objects above shall be 12 inches (305mm) minimum. (CBC Section 11B-609.3) Position of grab bars. Grab bars shall be installed in a horizontal position, 33 inches (838mm) minimum and 36 inches (914mm) maximum above the finish floor measured to the top of the gripping surface. (CBC Section 11B-609.4) Side wall. The side wall grab bars shall be 42 inches (1067mm) long minimum, located 12 inches (305mm) maximum from the rear wall and extending 54 inches (1372mm) minimum from the rear wall with the front end positioned 24 inches (610mm) minimum in front of the water closet (Fig.5). (CBC Section 11B ) Rear wall. The rear wall grab bar shall be 36 inches (914mm) long minimum and extend from the centerline of the water closet 12 inches (305mm) minimum on one side and 24 inches (610mm) minimum on the other side (Fig.6). (CBC Section 11B ) Figure 4 Spacing of Grab Bars (CBC 2013 Figure 11B-609.3) Figure 5 Side Wall Grab Bar at Water Closets (CBC 2013 Figure 11B ) Figure 6 Rear Wall Grab Bar at Water Closets (CBC Figure 11B )
4 Page 4 of 5 URINALS Urinals. Where one or more urinals are provided, at least one shall comply with Section 11B-605. (CBC Section 11B ) Height and depth. Urinals shall be the stall-type or the wall-hung type with the rim 17 inches (432mm) maximum above the finish floor or ground. Urinals shall be 13 ½ inches (343mm) deep minimum measured from the outer face of the urinal rim to the back of the fixture (Fig.4). (CBC Section 11B-605.2) LAVATORIES Lavatories. Where lavatories are provided, at least five percent but no fewer than one shall comply with Section 11B-606. (CBC Section 11B ) Clear floor space. A clear floor space complying with Section 11B-305 (Fig. 7), positioned for a forward approach, and knee and toe clearance complying with Section 11B-306 shall be provided. (Fig. 8 and 9 ) (CBC Section 11B-606.2) Clear floor space. A clear floor or ground space complying with Section 11B-305 positioned for forward approach shall be provided (Fig. 7). (CBC Section 11B-605.3) Flush controls. Flush controls shall be hand operated or automatic. Hand operated flush controls shall comply with Section 11B-309 except that the flush control shall be mounted at a maximum height of 44 inches (1118mm) above the finish floor. (CBC Section 11B-605.4) 48 min (a) Stall Hung Type Figure 4 Height and Depth of Urinals (CBC 2013 Figure 11B-605.2) (b) Wall Hung Type Figure 7 Clear Floor or Ground Space (CBC 2013 Figure 11B-305.3) 30 min
5 Page 5 of 5 Knee clearance. At lavatories required to be accessible by Section 11B , space between 9 inches (229mm) and 29 inches (737mm) above the finish floor or ground shall be considered knee clearance. (CBC Section 11B ) Minimum required depth. At Lavatories required to be accessible by Section 11B , the knee clearance shall be 27 inches (686mm) high minimum above the finish floor or ground at a depth of 8 inches (203mm) minimum increasing to 29 inches (737mm) high minimum above the finish floor or ground at the front edge of a counter with a built0in lavatory or at the front edge of a wall-mounted lavatory fixture. (CBC Section11B ) Clearance reduction. Between 9 inches (229mm) and 27 inches (686mm) above the finish floor or ground, the knee clearance shall be permitted to reduce at a rate of 1 inch (25mm) in depth for each 6 inches (152mm) in height. (CBC Section 11B ) Width. Knee clearance shall be 30 inches (762mm) wide minimum. (CBC Section 11B ) Height. Lavatories and sinks with the front of the higher rim or counter surface 34 inches (864 mm) maximum above the finish floor or ground. (CBC Section 11B-606.3) Faucets. Control faucets shall comply with Section 11B-309. Hand-operated metering faucets shall remain open for 10 seconds minimum. (CBC Section 11B-606.4) Exposed pipes and surfaces. Water supply and drain pipes under lavatories and sinks shall be insulated or otherwise configured to protect against contact. There shall be no sharp or abrasive surfaces under lavatories and sinks. (CBC Section 11B-606.5) Adjacent side or wall partition. Lavatories, when located adjacent to a side wall or partition, shall be a minimum of 18 inches (457mm) to the centerline of the fixture. (CBC Section 11B-606.6) Sink Depth. Sinks shall be 6 ½ inches (165mm) deep (CBC Section 11B-606.7) Figure 8 Toe Clearance (CBC 2013 Figure 11B ) Figure 9 Knee Clearance (CBC 2013 Figure 11B-306.3)
2016 CALIFORNIA BUILDING CODE - SECTION 11B-213 & DIVISION 6 GENERAL REQUIREMENTS FOR TOILET & BATHING FACILITIES
City Of Redwood City Community Development Department Building and Inspection Department 1017 Middlefield Road Redwood City, CA 94063 Phone (650) 780-7350 2016 CALIFORNIA BUILDING CODE - SECTION 11B-213
Accessible Toilet Stalls 6/18/03 1
Accessible Toilet Stalls 6/18/03 1 Section 11-4.17 Toilet Stalls Florida standard stall (11-4.17.3.1) In new construction the standard accessible stall shall contain an accessible lavatory within it, the
Priority 3 - Toilet Rooms
The ADA Checklist for Readily Achievable Barrier Removal Priority 3 - Toilet Rooms Project Building Location Date Surveyors Contact Information When toilet rooms are open to the public they should be accessible
Priority 3 - Toilet Rooms
The ADA Checklist for Existing Facilities Priority 3 - Toilet Rooms Based on the 2010 ADA Standards for Accessible Design Project Building Location Date Surveyors Contact Information When toilet rooms
KEYS TO COMPLIANCE ASSEMBLY AND MERCANTILE OCCUPANCIES ACCESSIBLE TOILET COMPARTMENTS. Figure 16 Handrail cross section {505.7}
KEYS TO COMPLIANCE : Grab bars are required to be at a height of 33 to 36 inches. A117.1 and 2010 Standards measure to the top of the graspable surface. Graphics in ADAAG and earlier editions of A117.1
ACCESSIBILITY DETAILS FOR RESTROOMS AND DRINKING FOUNTAINS
INFORMATION BULLETIN / PUBLIC - BUILDING CODE REFERENCE NO.: LABC Sec.11B-305,604,605 Effective: 01/01/2017 DOCUMENT NO.: P/BC 2017-087 Revised: Previously Issued As: P/BC 2014-087 ACCESSIBILITY DETAILS
ACCESSIBILITY REQUIREMENTS FOR SINKS
ACCESSIBILITY REQUIREMENTS FOR SINKS 1. Max. Height to top of counter at sink 2. Min. toe clearance 3. Plan view of 30 x48 clear space and depth 4. Min. knee clearance 5. Plan view of 30 x48 clear space
NCIDQ Restroom Drawing. Answers to the most common questions about this drawing for the Practicum Qpractice
NCIDQ Restroom Drawing Answers to the most common questions about this drawing for the Practicum. 2016 Qpractice Table of Contents This is a summary guide of most frequently asked questions about the Practicum
Paper Towel, Toilet Paper, Soap and Hand Sanitizer Dispensers
Paper Towel, Toilet Paper, Soap and Hand Sanitizer Dispensers 4.2.5* Forward Reach. If the clear floor space only allows forward approach to an object, the maximum high forward reach allowed shall be 48
WALKS AND SIDEWALKS REQUIREMENTS:
DOUBLE PARKING STALLS DIAGONAL PARKING STALLS EXTERIOR ROUTES OF TRAVEL: From accessible parking spaces, provide most practical direct accessible route of travel to all building entrances and exteriorground
REAR FRONT 93' 20' 12' 48' 120' 30' 52' 75' Sample Shopping Center. Unit # 5 +/- 10,920 GLA GROUND FLOOR. Width +/- 105' Depth +/- 120' Site Map
Electrical Information Breaker Panel 1: Service Type: 120/208 Panel Type: LP2 Panel Number: CHH31500 Manufacturer: Cutler Hammer Amps: 150 Location: Back Room Breaker Panel 2: Service Type: 120/208 Panel
ADA Barrier-Free Bathware for Assisted Living
This continuing education program is sponsored and provided to you due to the professional courtesy of: ADA Barrier-Free Bathware for Assisted Living Clarion Bathware 44 Amsler Ave. Shippenville, PA 16254
atm installation for accessibility a guide to ada/aba accessibility guidelines
atm installation for accessibility a guide to ada/aba accessibility guidelines WARNING This document supersedes all other information provided by Triton for ATM Installation for accessibility. Information
SECTION PLUMBING FIXTURES
SECTION 224000 - PLUMBING FIXTURES PART 1 - GENERAL 1.1 SUMMARY A. This Section includes 1. Faucets for lavatories and sinks. 2. Flushometers. 3. Toilet seats. 4. Protective shielding guards. 5. Fixture
404 Doors, Doorways, and Gates
404 Doors, Doorways, and Gates 404.2 Manual Doors, Doorways, and Manual Gates. Manual doors and doorways and manual gates intended for user passage shall comply with 404.2. 404.2.2 Double-Leaf Doors and
A.1 KING RESTROOM DEMOLITION PLAN. KING PARK 725 Monte Diablo Ave, San Mateo, CA LEGEND A.2 4 SCALE:
LEGEND EXISTING DEMO MEN'S WOMEN'S "STORAGE" "STORAGE" A.2 4 SCALE: KING DEMOLITION PLAN 4" = ' - 0" N COMPLIANCY NOTES - 30" MIN CLEARANCE FOR SINK WIDTH - DIAMETER FOR WHEELCHAIR ROTATION - 30" x 48"
Americans with Disabilities Act and Architectural Barriers Act Accessibility Guidelines
Americans with Disabilities Act and Architectural Barriers Act Accessibility Guidelines July 23, 2004 U N I T E D S T A T E S A C C E S S B O A R D A FEDERAL AGENCY COMMITTED TO ACCESSIBLE DESIGN TECHNICAL
City of Los Angeles Department of Building & Safety Disabled Access Section Supplemental Plan Review Checklist No. 2
City of Los Angeles Plan Check No. 1. Except building directories, menus, seat and row designations in assembly areas, occupant names, building addresses, and company names and logos, new or altered signs
Chapter 4. Accessible Routes
ICC/ANSI A117.1-2003 401 General 401.1 Scope. Accessible routes required by the scoping provisions adopted by the administrative authority shall comply with the applicable provisions of Chapter 4. 402
COMMERCIAL VISUAL INDEX LOBBIES COMMERCIAL VISUAL INDEX NURSE S STATIONS. General Safety. General Safety. Kitchens
VISUAL INDEX NURSE S STATIONS Solid Surfacing by Formica Group 6 4 Solid Surfacing by Formica Group 65 VISUAL INDEX LOBBIES SIGNAGE Hand Rails pg 71-75 WALL APPLICATION pg 67-70 UNDERMOUNTED SINKS pg 28-31
WASHROOM ACCESSORIES 2013 CATALOG
WASHROOM ACCESSORIES 2013 CATALOG Washroom Accessories engineered for the high traffic restroom. 12-14 GAUGE STAINLESS STEEL 1 Paper Towel Dispenser C-Fold or Multi-Fold Towels Refill indicator slot Heavy
CKBD Peakes Bath Scoresheet
CKBD Peakes Bath Scoresheet Part I: Graphics & Presentation Standards Each question pertains to all four drawing documents: Floor Plan, Mechanical, Construction Plan, and Elevation Drawing unless specifically
Dry Toilet, Version 2.0 June 17, 2015
Dry Toilet, Version 2.0 June 17, 2015 Concrete Base When forming the concrete base, make sure it is same or slightly larger dimensions than the wooden base described below. The urine drain pipe is accommodated
CITY OF LONG BEACH Department of Development Services BUILDING AND SAFETY BUREAU SIGNS SUPPLEMENTAL ACCESSIBILITY PLAN REVIEW CHECKLIST NO.
INFORMATION INSTRUCTIONS CITY OF LONG BEACH Department of Development Services BUILDING AND SAFETY BUREAU SIGNS SUPPLEMENTAL ACCESSIBILITY PLAN REVIEW CHECKLIST NO. 2 PROJECT NO.: EXPIRATION DATE: STATUS:
Installation Manual. Solid Plastic Toilet Partitions. IN CANADA & AREAS OTHER THAN U.S.A.: IN THE U.S.A.:
Installation Manual Solid Plastic Toilet Partitions Toilet Partitions & Lockers IN THE U.S.A.: Hadrian Inc., 7420 Clover Avenue, Mentor, OH 44060 Telephone: 440-942-9118 Fax: 440-942-9618 U.S. toll free
INSTALLATION AND CUSTOMER CARE INFORMATION FOR SC FREESTANDING STERILIZATION CENTERS
INSTALLATION AND CUSTOMER CARE INFORMATION FOR SC144-200 FREESTANDING STERILIZATION CENTERS General Information: Many Artizan Design Free-standing Sterilization Centers are custom designed and built to
Booth Display Rules. Standard Inline booth. Perimeter booth. Island booth. Peninsula Booth
Booth Display Rules Standard Inline booth A standard inline booth is 10 ft (3.05 m) deep and 10 ft wide or a multiple thereof. It is enclosed on three sides by a back wall and two sidewalls, except for
LUCERNE WALL-HUNG LAVATORY
-HUNG LAVATORY LUCERNE -HUNG LAVATORY Wall-hung sink Vitreous china Front overflow D-shaped bowl Self-draining deck area with contoured back and side splash shields Faucet ledge Faucet holes on centers
grab BarS and rails 800 SerieS
grab BarS and rails 800 SerieS All Bradley Grab Bars are designed for safety and security of the physically disabled. The safety clearance feature is highly recommended by Barrier-Free design experts and
INSTALLATION AND CUSTOMER CARE INFORMATION FOR SC FREESTANDING STERILIZATION CENTERS
INSTALLATION AND CUSTOMER CARE INFORMATION FOR SC120-200 FREESTANDING STERILIZATION CENTERS General Information: Many Artizan Design Free-standing Sterilization Centers are custom designed and built to
Installation. *HDWC-INSTR-008* HDWC-INSTR-008 Rev. H; ECN G 2018 Bradley Page 1 of 24 3/22/2018
Installation Phenolic Restroom Partitions Floor-To-Ceiling Series 700 For Standard Height Doors and Panels Only Table of Contents Pre-Installation Information... 2-3 Layout Dimensions for rackets...4 Mounting
TOILET ROOM ACCESSORIES Concrete Unit Masonry Carpentry Ceramic Tile Solid Plastic Toilet Partition.
SECTION 10800 TOILET ROOM ACCESSORIES PART 1 GENERAL 1.01 SUMMARY A. Related Sections: 1. 04220 - Concrete Unit Masonry. 2. 06100 - Carpentry. 3. 09310 - Ceramic Tile. 4. 10170 - Solid Plastic Toilet Partition.
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Special-Lite Restroom Partitions IMPORTANT - BEFORE YOU START... 1. Read through these installation instructions first to understand the order of work. 2. Check all components
INSTALLATION INSTRUCTION
INSTALLATION INSTRUCTION Plastic Laminate Series contents page 1030 TrimLineSeries...2-21 1040 DesigerSeries...2-21 Urinal Screens, Benches, Shower Seats...22-31 2030 TrimLineSeries Maximum Privacy...32-47
Advisory Raised Characters. Signs that are designed to be read by touch should not have sharp or abrasive edges.
ADAAG/ABA* US Access Board 7/23/04 *Not the enforceable standard for accessibility under the ADA. This document has not been adopted by the US Department of Justice as enforceable under Title II and III
Gerber Fixtures. Ultra Flush 1.6 GPF Pressure Assist Color Prod. ID Combination Bowl Tank Rough-In
2018 PAGE 108-1 Gerber Fixtures Please see www.gerberonline.com/shop for product descriptions and photos. Items in Bold are currently stocked at Roberts-Hamilton Company Prod.ID is for the Combination
Installation Instructions
Installation Instructions For Models: Model Number / Description File Name 1540 Classic Series P-Lam Toilet Partitions 1540.pdf 1 INSTALLATION INSTRUCTIONS LAMINATED PLASTIC TOILET PARTITIONS 1540 Classic
Kitchen and Bath Design Planner
2017 Kitchen and Bath Design Planner How to Measure Your Kitchen or Bath for New Cabinets Measuring your space is a critical step in determining your room layout. Having accurate measurements of your kitchen
Environmental component, the complete Housing Enabler instrument. Susanne Iwarsson & Björn Slaug Yes
Environmental component Environmental component, the complete Housing Enabler instrument. Susanne Iwarsson & Björn Slaug 2010. Personal component / functional profile A. EXTERIOR SURROUNDINGS RATING General
Chapter General. Accessible built-in storage facilities shall comply with Section 905. Chapter 9. Built-in Furnishings and Equipment
Chapter 9 9-1 12 901.1 Scope. Built-in furnishings and equipment required to be accessible by the scoping provisions adopted by the administrative authority shall comply with the applicable provisions
PLASTIC BALLCOCK Includes: Vinyl Refill Tube, Float Rod, Flange Nut, Washer, 5/8 or 1/2 Coupling Nut and Water Level Adjustable Screw.
Flush Valves PLASTIC BALLCOCK Includes: Vinyl Refill Tube, Float Rod, Flange Nut, Washer, 5/8 or 1/2 Coupling Nut and Water Level Adjustable Screw. Toilet Flappers 51005 10 Anti siphon 5 50 6.25 P51005
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SOLID PHENOLIC TOILET PARTITIONS 1080 DuraLineSeries Class-A Fire Rated Includes Institutional Hardware Option.67 IMPORTANT: Storage and Handling Information on last page. Review
Installation Instructions 50 (06-09) 1-15/32 15/32 21/32. 1/4-20 x 5/8" FHMS or #14 x 1/2" FHWS 1/16 1/4. Floor Plate
RIXSON ASSA ABLOY 3/4 Template Jamb 1/8 2- R. Max. 1-7/16 1-1/32 2-2-3/4 7/8 Dia. C L 1-1/4 Dia. Installation Instructions 50 (06-09) Finish Plate 340 TOP PIVOT Pivot Shown Engaged 9/16 1/16 1/4 1-15/32
Installation. *HDWC-INSTR-006* HDWC-INSTR-006 Rev. K; ECN G 2018 Bradley Page 1 of 24 3/22/2018
Installation Phenolic Restroom Partitions Floor-raced Series 500 For Standard Height Doors and Panels Only Table of Contents Pre-Installation Information... 2-3 Layout Dimensions for rackets...4 Mounting
City of Thousand Oaks
TENANT IMPROVEMENT SUBMITTAL CHECKLIST SUBMIT THREE SETS OF SCALED DRAWINGS (ONE TO BE A BLACKLINE SET) WITH THE FOLLOWING INFORMATION: 1. 2. 3. 4. 5. 6. 7. 8. 9. SITE PLAN: Show building location (vicinity
GRAF HALL ADA ASSESSMENT & SURVEY
OREGON STATE UNIVERSITY (OSU) GRAF HALL ADA ASSESSMENT & SURVEY Sacramento Office 770 L Street, Suite 950 Sacramento, CA 95814 Tel: 916.669.8750 Fax: 888.211.7441 Silicon Valley Office 2225 E. Bayshore
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS HIGH PRESSUE LAMINATE (HPL) TOILET PARTITIONS 1030 TrimLineSeries 1040 DesignerSeries Includes continuous hardware option.65. IMPORTANT: Storage and Handling Information on last
SECTION MECHANICAL IDENTIFICATION
SECTION 15190 MECHANICAL IDENTIFICATION PART 1 GENERAL 1.01 SECTION INCLUDES A. Section Includes: 1. Nameplates. 2. Tags. 3. Stencils. 4. Pipe Markers. 1.02 SUBMITTALS A. Submit valve chart and schedule,
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Cossu Wall Mount, Pedestal and Above Counter Lavatories Thank you for selecting DXV. To ensure this product is installed properly, please read these instructions carefully before
A. It is preferred that all submittals to be submitted electronically in PDF format.
June 20 2013, Rev 00 10 2800 Toilet, Bath, and Laundry Accessories PART 1. GENERAL 1.01 This Section includes: A. Toilet room accessories: 1.02 Submittals 1. Grab bars 2. Metal framed mirrors 3. Sanitary
IMPORTANT: installation. FLOOR ANCHORED CEILING HUNG OVERHEAD BRACED FLOOR-TO- CEILING ANCHORED
INSTALLATION INSTRUCTIONS MAXIMUM PRIVACY COMPACT LAMINATE TOILET PARTITIONS 2080 DuraLineSeries 2180 DuraLineSeries Class-A Fire Rated Includes Institutional Hardware Option.67 IMPORTANT: Storage and
Jan H: ARCHITECTURAL WOODWORK (06410-H)
2101 Commonwealth Blvd, Suite B Ann Arbor, MI 48105-5759 www.med.umich.edu/facilities/plan/ 064040-H: ARCHITECTURAL WOODWORK (06410-H) GENERAL In general, follow the guidelines below when designing and
ODEON SIN GLE VAN ITY SIN K ASSE MBLY IN STRUCTIONS
1. Storage 1. Keep marble top in it s crate until installation. 2. Store crate vertically in a place safe from being hit or knocked over 3. Do not stack anything on top of the crate. 2. Opening crate 1.
ADDENDUM THREE SPECIFICATIONS. Vincennes University Renovations of the Curtis G. Shake Learning Resources Center
ADDENDUM THREE Addendum Three (AD.03) to the drawings and specifications prepared by Gibraltar Design for Curtis G. Shake Learning Resources Center for Vincennes University, Vincennes, Indiana. All Contractors
A. This Section includes plumbing fixtures and related components.
SECTION 224200 PLUMBING FIXTURES PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of the Contract, including General and Supplementary Conditions and Division 01 Specification
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SOLID PHENOLIC TOILET PARTITIONS 1080 DuraLine Series 1180 DuraLine Series Class-A Fire Rated IMPORTANT: Review these instructions thoroughly prior to installation. FLOOR ANCHORED
Installation Instructions
AMPCO Solid Plastic Toilet Partitions AMPCO Florida 11400 NW 36 th Avenue Miami, FL 33167 T. 305.821.5700 florida@ampco.com AMPCO Texas 201 Railroad Avenue Sanger, TX 76266 T. 940.458.7401 texas@ampco.com
Installation. *HDWC-INSTR-007* HDWC-INSTR-007 Rev. K; ECN G 2018 Bradley Page 1 of 24 3/22/2018
Installation Phenolic Restroom Partitions, Ceiling-Hung Series 600 Table of Contents Pre-Installation Information... 2-3 Layout Dimensions for rackets...4 Mounting rackets to Wall... 5-6 Leveling rackets
2016 CDM Smith All Rights Reserved July 2016 SECTION PLUMBING - FIXTURES AND TRIM
PART 1 GENERAL 1.01 SCOPE OF WORK SECTION 22 40 00 PLUMBING - FIXTURES AND TRIM A. Furnish all labor and materials required and install the following Plumbing Fixtures and companion Fixture Trim complete
MACHINTO SINGLE VANITY SINK ASSEMBLY INSTRUCTIONS. 1. Storage. 1. Keep marble top in its crate until installation.
1. Storage 1. Keep marble top in its crate until installation. 2. Store crate vertically in a place safe from being hit or knocked over. 3. Do not stack anything on top of the crate. 2. Opening crate 1.
BioPrism Solid Surface
Please read all instructions before installing products. These instructions are intended for use with InPro s standard toilet partitions, which include 58 high doors and wall panels, when deviating from
Installation Manual for Metal Toilet Partitions Standard Series
For Video instructions http://www.hadrian-inc.com/tech-data/installation/toilet-partitions.aspx P a g e 1 Table of Contents Page General Notes and Tools Required 3 STEP 1: Establish Floor Bracket Locations
MACHINTO FLOATING DOUBLE VANITY SINK ASSEMBLY INSTRUCTIONS. 1. Storage. 1. Keep marble top in its crate until installation.
1. Storage 1. Keep marble top in its crate until installation. 2. Store crate vertically in a place safe from being hit or knocked over. 3. Do not stack anything on top of the crate. 2. Opening crate 1.
Bathroom Installation Manual
Bathroom Installation Manual MAKING SPACE MORE VALUABLE May 2016 1 2 Contents page 1. Introduction Page 4 2. Tools required / key Page 5 3. Fittings Page 6 4. 600 cistern unit Page 7 5. 600 vanity unit
INSTALLATION GUIDE KITCHEN SINKS
INSTALLATION GUIDE KITCHEN SINKS Tools and Materials Tape Measure Safety Glasses Saw Construction Adhsive Suitable Support Framing Material [3/4" (1.9 cm) Max Thickness] Screws Important Information IMPORTANT!
ADDENDUM NOTICE INTERIOR RENOVATIONS AT THE BATHURST CLARK RESOURCE LIBRARY, 900 CLARK AVENUE WEST, VAUGHAN, ON
The City of Vaughan Procurement Services Department 2141 Major Mackenzie Drive Vaughan, ON L6A 1T1 Tel (905) 832-8555 ADDENDUM NOTICE ADDENDUM NO. 3 Total of (5) page BID NO. T18-003 DESCRIPTION: INTERIOR
Part VIII Electrical GENERAL REQUIREMENTS CHAPTER 33
Part VIII Electrical CHAPTER 33 GENERAL REQUIREMENTS < SECTION E3301 GENERAL E3301.1 Scope. The installation of electrical systems, equipment and components indoors and outdoors that are within the scope
INSTRUCTIONS. Taurus (BM) Unit Assembly
INSTRUCTIONS Taurus (BM) Unit Assembly Tool Selection QTY Description QTY Description 1 Flat head screw driver 1 Air ratchet 1 Drill with ¼ Bit 1 7/16 deep well socket (for wood base) 1 Drill with 3/16
FOLIO COUNTERTOP LAVATORY
FOLIO COUNTERTOP LAVATORY 1. BEFORE YOU BEGIN HOW TO USE THESE INSTRUCTIONS Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences.
1. Name the horizontal member that rests on the foundation wall to support other wood members.
Student Name: Teacher: Date: District: Rowan Assessment: 9_12 T and I IC62 - Drafting - Architr II Test 1 Description: Unit C - Floorplans - Test 3 (ALL) Form: 501 1. Name the horizontal member that rests
INSTALLATION INSTRUCTIONS FOR ALPACO CLASSIC PARTITIONS
INSTALLATION INSTRUCTIONS FOR ALPACO CLASSIC PARTITIONS Table of Contents Topic Page Layout and Wall Brackets 2 Panel and Pilaster Preparation.. 3 Securing Components and Headrail 4 Panel to Pilaster/Wall
s t o r a g e & i n s t a l l a t i o n o f y o u r m a r b l e t o p
s t o r a g e & i n s t a l l a t i o n o f y o u r m a r b l e t o p 1. Storage 1. Keep marble top in it s crate until installation. 2. Store crate vertically in a place safe from being hit or knocked
Installation *HDWL-INSTR-001* IMPORTANT. Plastic Laminate Restroom Partitions Floor-Mounted with Overhead Brace Series 400
Plastic Laminate Restroom Partitions Floor-Mounted with Overhead race Series 400 For Standard Height Doors and Panels Only Table of ontents Pre- Information...2 Layout Dimensions for rackets...3 Mounting
P a r k c o n s o l e s i n k a s s e m b l y i n s t r u c t i o n s
P a r k c o n s o l e s i n k a s s e m b l y i n s t r u c t i o n s Before You Begin: Professional installation by two-person crew is required for this fixture. Install water supply and drain piping
***************************************************************************************************************
10800 TOILET ROOM ACCESSORIES SPECIFIER: CSI MasterFormat 2004 number 10 28 13 PART 1 GENERAL 1.1 SUMMARY A. Related Sections: 1. 04220 - Concrete Unit Masonry. 2. 06100 - Carpentry. 3. 09310 - Ceramic
ST JAMES EXTRA WIDE VANITY SINK ASSEMBLY INSTRUCTIONS. 1. Storage. 1. Keep marble top in it s crate until installation.
1. Storage 1. Keep marble top in it s crate until installation. 2. Store crate vertically in a place safe from being hit or knocked over 3. Do not stack anything on top of the crate. 2. Opening crate 1.
SCI-FAB Product Specifications. Casework Section 1. Part 1 General
SCI-FAB Product Specifications Casework Section 1 Part 1 General 1.1 SCOPE OF WORK Includes all factory fabricated stainless steel casework as required by the project drawings. 1.2 TYPICAL INCLUSIONS A.
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS HIGH PRESSUE LAMINATE (HPL) TOILET PARTITIONS 1030 TrimLineSeries 1040 DesignerSeries Includes continuous hardware option.65. IMPORTANT: Storage and Handling Information on last
JAMESTOWN175 SERIES Fixed, Projected and Casement Steel Windows
Fixed, Projected and Casement Steel Windows Hope s Jamestown Series steel windows are manufactured from heavy custom hot-rolled steel profiles. All frames, ventilators and muntin bars are -/" in depth.
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS MAXIMUM PRIVACY HIGH PRESSURE LAMINATE (HPL) TOILET PARTITIONS 2030 TrimLineSeries 2040 DesignerSeries IMPORTANT: Storage and Handling Information on last page. Review these instructions
EXHIBIT DISPLAY GUIDELINES
EXHIBIT DISPLAY GUIDELINES The following Guidelines for Display Rules and Regulations have been established by the International Association of Exhibitions and Events (IAEE). Guidelines for Display Rules
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS COMPACT LAMINATE TOILET PARTITIONS 1080 DuraLineSeries 1180 DuraLineSeries Class-A Fire Rated Includes Institutional Hardware Option.67 IMPORTANT: Storage and Handling Information
INSTALLATION INSTRUCTION
INSTALLATION INSTRUCTION Soild Phenolic Series contents page 1080 DuraLineSeries...2-21 1180 DuraLineSeries...2-21 2080 DuraLineSeries Maximum Privacy...22-41 2180 DuraLineSeries Maximum Privacy...22-41
INSTRUCTIONS FOR HIT-41 SERIES ELECTRIC STRIKE TEMPLATES WHEN USING POWER TOOLS ALWAYS WEAR EYE AND EAR PROTECTION!!
1825 VIA BURTON ANAHEIM CA 92806 714-772-5202 / FAX 714-772-2302 EMAIL: MAIL@MAJORMFG.COM WEB: WWW.MAJORMFG.COM INSTRUCTIONS FOR HIT-41 SERIES ELECTRIC STRIKE TEMPLATES WHEN USING POWER TOOLS ALWAYS WEAR
Infinity 20 Min. FIRE RATED DOORS WARNOCK HERSEY INFINITY - STANDARD RAISED - 20 MIN. RATING SOFTWOOD STILE
Infinity 20 Min Note: 20 Minute (Positive Pressure) Category A & B Manufacturing Specifications MAXIMUM SIZES All doors shall have a minimum thickness of 1-3/4" + 1/16" Single Swing: 4/0 x 9/0 Standard
TOOLS REQUIRED Metal Wood Wood and Metal Screws. #16 Drill #12-24 Tap. 1/8 Drill
DEVICES COVERED IN THIS DOCUMENT: 4700S Surface Vertical Rod Device 4700SF Fire Exit Surface Vertical Rod Device TOOLS REQUIRED Metal Wood Wood and Metal Screws Sex Bolts #7 Drill ¼ -20 Tap #16 Drill #12-24
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS LAMINATED P LASTIC TOILET PArTITIONS 1540 ClassicSeries with Options IMPORTANT: Storage and Handling Information on last page. For faster, easier installation, please review these
Sitting Height Base Cabinets
Sitting Height Base Cabinets Signature Series 30" These Sitting Height Cabinets are 30" high and a deep. engths as shown. Open and Cupboard cabinets have one adjustable shelf. Open Cubbie cabinets have
WADE 2-1. Universal Carrier. Exclusive Features of 400 Series Universal Carrier for Lavatories, Urinals, Drinking Fountains.
Universal Carrier Exclusive Features of 400 Series Universal Carrier for Lavatories, Urinals, Drinking Fountains. The 400 series carrier accommodates most urinal, water-cooler or hanger plate lavatory
Table of Contents IMPORTANT
Plastic Laminate Restroom Partitions Floor-raced Series 500 For Standard Height Doors and Panels Only Table of ontents Pre- Information...2 Layout Dimensions for rackets...3 Mounting rackets to Wall...4
The following information supplements and/or supersedes the bid documents issued on July 10, 2017.
Addendum No. 02 ADDENDUM Pages 2 Project No. 1706 Date: July 21, 2017 Project: West End Lofts 44 MacDonald Street, Arnprior, ON The following information supplements and/or supersedes the bid documents
Made possible by a generous grant from. Guidelines for Display Rules & Regulations 2014 Update
Made possible by a generous grant from Guidelines for Display Rules & Regulations 2014 Update X PERIMETER BOOTH Contents (3.658M) 12' Linear Booth and Corner Booth 4 (3.658M) 12' 12' Perimeter Booth 5
Encore 20 Min. FIRE RATED DOORS WARNOCK HERSEY ENCORE - STANDARD PANEL - 20 MIN. RATING
Encore 20 Min 20 Minute (Positive Pressure) - Category B Manufacturing Specifications MAXIMUM SIZES All doors shall have a minimum thickness of 1-3/4" + 1/16" Single Swing: 4/0 x 8/0 Standard Pair: 8/0
SECTION CHAIN LINK FENCING
SECTION 32 31 13 CHAIN LINK FENCING PART 1 - GENERAL 1.01 SECTION INCLUDES A. The Work specified in this Section consists of furnishing and installing permanent chain link fences and gates in accordance
Installation Instructions 3040 (05-09) 9/16 9/ /32 9/32. Checking Adjustments
RIXSON ASSA ALOY Template 3/4 1/8 2- R. Max 1-7/16 1-1/32 2-2-3/4 7/8 Dia. C L Spindle Installation Instructions 3040 (05-09) 9/16 9/32 1/16 Finish Plate 1/4 1-1/4 Dia. 340 TOP PIVOT PIVOT SHOWN ENGAGED
Tuxedo Console Table INSTALLATION INSTRUCTIONS P73037, P73038, P _2_B Page 1 of 5
P73037, P73038, P73039 Page 1 of 5 THANK YOU FOR CHOOSING KALLISTA We appreciate your commitment to Kallista quality products. Please take a moment to review this manual before you install your Kallista
I N T E R N A T I O N A L R E S I D E N T I A L CO D E
I N T E R N A T I O N A L R E S I D E N T I A L CO D E 2006 STAIR BUILDING CODE Portions of this document reproduce sections from the 2006 International Residential Code, International Code Council, Falls
BEZIER DOUBLE FLOATING VANITY ASSEMB L Y INSTRUCTIONS
BEZIER DOUBLE FLOATING VANITY ASSEMB L Y INSTRUCTIONS 1. Storage 1. Keep marble top in its crate until installation. 2. Store crate vertically in a place safe from being hit or knocked over. 3. Do not
ASPEN FRENCH OAK SINGLE EXTRA-WIDE VANITY ASSEMBLY INSTRUCTIONS
1. Storage 1. Keep marble top in its crate until installation. 2. Store crate vertically in a place safe from being hit or knocked over. 3. Do not stack anything on top of the crate. 2. Opening crate 1.
SECTION CHAIN LINK FENCING AND GATES AND SOFTBALL BACKSTOP
1 1 1 0 1 0 1 0 1 SECTION 1 1 CHAIN LINK FENCING AND GATES AND SOFTBALL BACKSTOP BASED ON DFD MASTER SPECIFICATION DATED /01/ P A R T 1 - G E N E R A L SCOPE The work under this section shall consist of