Staybridge Suites Standardized Room Decor Vista, Spice, Chocolate, Sage Schemes Guestroom

Transcription

1 Vista, Spice, Chocolate, Sage Schemes Guestroom AREA: Guestroom Atlanta, GA Johnsonite Attn: John Stoll 5043 Abbey Lane Lilburn, GA P: / F: E: jstoll@johnsonite.com MODEL/STYLE NO: FINISH/COLOR: SG-B-1 (VPCS) Vinyl Base at Guestroom Millwork Reveal Profile 167 Fudge Field verify all dimensions, 4.25 Height 1. Vinyl base to be of contract quality and suitable for commercial use. 2. Vinyl base to be installed at kitchen cabinets flush to floor. (Cabinet toe kick: 4.5 built in) 3. To be installed by General Contractor. (Cabinets must be installed on finish floors or built-up even with finished floors so that toe-kick dimension is not compromised.) 4. Field verify all dimensions before installation. 5. GC to verify quantity requirements prior to order. 6. Base to be installed under cabinets and within kitchen and guestroom. All corners to be mitred. Not to Scale / Design Intent Only 10/15/11 6/21/12 1 SG-B-1 (VPCS)

2 AREA: Bathroom Atlanta, GA Dal Tile Attn: John Hall 1630 Satellite Blvd. Duluth, GA P: E: TYPE: SERIES: COLOR: GROUT: SG-B-2 (V) Tiile Base at Bathroom Colorbody porcelain Trim Kimona Silk Panda Black / P /4" x 12" cut from 12"x12" with manufactured bullnose edge down 12" side Laticrete #45 Raven 1. Refer to image below for tile. 2. Tile to be of contract quality and suitable for commercial use. 3. Per manufacturer, product meets the following: Pre-consumer RMC: 6.5%, Postconsumer RMC: 0.0%, ASTM C1028: COF wet > 0.60; COF dry > 0.70, ASTM C373: Moisture absorption < 0.5%, ASTM C648: Breaking Strength > 450lbs, ASTM C650: Chemical Resistance = Resistant, MOH s: Scratch Hardness = Installer to verify quantity ordered. 5. Recommended grout joint: 1/8. Wall base grout lines to be lined up with floor grout lines. 6. Grout to be provided by General Contractor. No substitutions allowed. 7. Refer to ST-T-1 (V) for bathroom floor tile. 8. This is not a stocked product and will need to be fabricated locally by a bullnose factory or via the tile contractor on site. Corners should not be mitered but have one piece butt up against a piece with a double bullnose edge (bullnose along the 6" and 12" side). Not to Scale / Not for Color / Design Intent Only 10/01/11 SG-B-2 (V)

3 AREA: Guestroom Atlanta, GA Durkan Hospitality Attn: Dawn Morris 405 Virgil Drive Dalton, GA P: / F: E: dawn_morris@mohawkind.com SG-CPT-1 (V) Broadloom Carpet at Guestroom STRIKE-OFF: G W CONSTRUCTION: 1/10 FRL PRIMARY BACKING: Woven Polypropylene; SECONDARY BACKING: Action Bac DYE METHOD: Solution YARN: Colorstrand TUFTED WEIGHT: 32 oz. TUFTED PILE HEIGHT:.343,.218,.093 STITCHES PER INCH: 12.9 CONTENT: Type 6 Nylon (25% recycled Content) CARPET BASE: Vinyl Base Refer to SG-VB-1(VPCS) PATTERN REPEAT: 36 W x 50.3 L 1. Refer to image below for guestroom carpet. 2. Must be contract quality, suitable for commercial use. 3. Per manufacturer carpet meets or exceeds the following standards: Pill Test 16CFR (FF-1-70), ASTM E-648 Class 1, ASTM E or Less, AATCC 16E Min. Rating 60 AFU, AATCC 134 (STEP) Less than 3.5 K.V. 4. Installer responsible for on-site measurements and verifying yardage requirements. 5. Padding: EcoComfort Step 32 oz. or SmartStep 32 oz. Carpet pad required. 6. Vinyl Base Refer to specification SG-VB-1(VPCS). 7. Installation: must be installed according to manufacturer's directions and per brand standards. 8. Adhesive: NuBroadlok Premium Plus, NuBroadlock Seam Sealer. 9. Refer to drawings for location. 6/11/12 SG-CPT-1 (V)

4 AREA: Guestroom Atlanta, GA Not to Scale; Not for Color 6/11/12 SG-CPT-1 (V)

5 AREA: Guestroom Atlanta, GA Sherwin Williams Attn: Sheri Thompson 101 Prospect Avenue, 1000 M Cleveland, OH P: F: E: sheri.a.thompson@sherwin.com SG-PT-1 (V) Paint at Main Walls MODEL/STYLE NO: SW 6148 COLOR : FINISH: Wool Skein Eggshell Finish 1. Refer to image below for paint color. 2. Product to be of contract quality and suitable for commercial use. 3. To be Sherwin Williams Harmony Low Odor/0-VOC Paint OR ProGreen 200 Low VOC Paint. 4. Contractor to determine required paint quantity. 5. Substitutions of manufacturer are not permitted without prior written approval by IHG. 6. Refer to SG-PT-2 (V) for accent paint at headboard wall. 7. Refer to finish plans for location. Not for Color 10/01/11 SG-PT-1 (V)

6 AREA: Bedroom Atlanta, GA Sherwin Williams Attn: Sheri Thompson 101 Prospect Avenue, 1000 M Cleveland, OH P: F: E: sheri.a.thompson@sherwin.com SG-PT-2 (V) Accent Paint Color at Headboard Wall MODEL/STYLE NO: SW 6234 COLOR : FINISH: Uncertain Gray Egg Shell 1. Refer to image below for paint color. 2. Product to be of contract quality and suitable for commercial use. 3. To be Sherwin Williams Harmony Low Odor/0-VOC Paint OR ProGreen 200 Low VOC Paint. 4. Contractor to determine required paint quantity. 5. Substitutions of manufacturer are not permitted without prior written approval by IHG. 6. Refer to SG-PT-1 (V) for paint at main walls. 7. Refer to finish plans for location. Not for Color 10/01/11 SG-PT-2 (V)

7 AREA: Bathroom Atlanta, GA Sherwin Williams Attn: Sheri Thompson 101 Prospect Avenue, 1000 M Cleveland, OH P: F: E: sheri.a.thompson@sherwin.com SG-PT-3 (V) Paint Bathroom Walls MODEL/STYLE NO: SW 6149 COLOR : FINISH: Relaxed Khaki Semi-Gloss 1. Refer to image below for paint color. 2. Product to be of contract quality and suitable for commercial use. 3. To be Sherwin Williams Harmony Low Odor/0-VOC Paint OR ProGreen 200 Low VOC Paint. 4. Contractor to determine required paint quantity. 5. Substitutions of manufacturer are not permitted without prior written approval by IHG. 6. Refer to finish plans for location. Not for Color 10/01/11 SG-PT-3 (V)

8 AREA: Guestroom Atlanta, GA Sherwin Williams Attn: Sheri Thompson 101 Prospect Avenue, 1000 M Cleveland, OH P: F: E: sheri.a.thompson@sherwin.com SG-PT-4 (V) Paint at Trim MODEL/STYLE NO: SW 6385 COLOR : FINISH: Dover White Semi-gloss 1. Refer to image below for paint color. 2. Refer to PT-8 for trim color at entry door. 3. Product to be of contract quality and suitable for commercial use. 4. To be Sherwin Williams Harmony Low Odor/0-VOC Paint OR ProGreen 200 Low VOC Paint. 5. Contractor to determine required paint quantity. 6. Substitutions of manufacturer are not permitted without prior written approval by IHG. 7. Refer to finish plans for location. Not for Color 10/01/11 7/18/12 1 SG-PT-4 (V)

9 AREA: Guestroom Sherwin Williams Attn: Sheri Thompson 101 Prospect Avenue, 1000 M Cleveland, OH P: F: E: sheri.a.thompson@sherwin.com SG-PT-5 (V) Ceiling Paint MODEL/STYLE NO: SW 7007 COLOR : FINISH: Ceiling Bright White Flat Finish at Guestroom Ceiling Satin Finish at Bathroom Ceiling 1. Refer to image below for paint color. 2. Product to be of contract quality and suitable for commercial use. 3. To be Sherwin Williams Harmony Low Odor/0-VOC Paint OR ProGreen 200 Low VOC Paint. 4. Contractor to determine required paint quantity. 5. Substitutions of manufacturer are not permitted without prior written approval by IHG. 6. Refer to plans location. Not for Color 10/01/11 SG-PT-5 (V)

10 Vista, Spice, Chocolate and Sage Schemes Guestroom AREA: Kitchen Atlanta, GA MANUFACTURER I: MANUFACTURER II: Remanufacturing Project Stone, by Belstone Attn: Scott Deutsch Attn: Diane Tolentino P: Haskell Avenue F: Van Nuys, CA E: P: x-21 E: Field Rep: Zach Grabinski P: E: MODEL/STYLE NO: FINISH: CONTENT: SG-ST-1 (VPCS) Kitchen Countertop Remanufacturing: Beige Microflec Project Stone: EcoQuartz Collection, Color: Khaki Polished Outside Edges: Eased Edges at Cut-outs: 3/16 radius Quartz All Dimensions Must be Field Verified 2 cm thick slab with 2 cm laminated edge (overall edge: 4 cm). Refer to architectural drawings for overall dimensions. 1. Refer to image below for countertop finish. 2. Product to be of contract quality and suitable for commercial use. 3. Manufacturer to submit finish sample to IHG for written approval prior to production. 4. Stone top to be pre-cut prior to shipment for drop-in sink and cook-top. Field verify all dimensions. 5. Refer to SG-104 for typical kitchen sink. Refer to SG-111 for typical cook-top. 6. Edges: Eased at outside edge. 3/16 radius at cut-outs. All exposed edges to be polished. 7. Backsplash: Quartz to be at countertop only, not at backsplash. Refer to SG-ST-2 for backsplash. 8. Overhang: 1 overhang over cabinets (field verify). 9. Refer to drawings for further detail. 10. Refer to drawings for location. Not to Scale / Not for Color Design Intent Only 10/15/11 7/13/12 1 SG-ST-1 (VPCS)

11 Vista, Spice, Chocolate, Sage Schemes Guestroom AREA: Kitchen Atlanta, GA MANUFACTURER I: MANUFACTURER II: Porcelanosa Dal Tile 600 Route 17 North Attn: John Hall Ramsey, NJ Satellite Blvd. P: (Option 3, Option 1) Duluth, GA F: (order line) P: E: E: E: W: W: PRODUCT: GROUT: SG-ST-2 (VPCS) Kitchen Backsplash Porcelanosa: L (Mosaic Strip Mix Crema Glacier) Dal-Tile: (Northstar Crema Linen Random CST blend) #382 Bone Porcelanosa: 12 x 12 sheet, ¼ thick Dal-Tile: Overall Sheet: 11 ¾ x 12 ½, 5/16 thick 1. Refer to image below for backsplash (design intent only). 2. Product to be of contract quality and suitable for commercial use. 3. Decorative backsplash to go from top of countertop to wall cabinet. Right/Left ends to be aligned with countertop and upper cabinets. Field verify overall height. To be installed by General Contractor. 4. Right and left ends of backsplash to be covered with Schluter Strip. Refer to specification SG-TR-4 for Schluter Strip. 5. Grout Joint: 1/8 6. Refer to drawings/elevations for further detail. 7. Refer to drawings/elevations for location. Not to Scale / Not for Color Design Intent Only 10/15/11 7/13/12 1 SG-ST-2 (VPCS)

12 Vista, Spice, Chocolate, Sage Schemes Guestroom AREA: Kitchen Atlanta, GA MANUFACTURER I: MANUFACTURER II: Remanufacturing Project Stone, by Belstone Attn: Scott Deutsch Attn: Diane Tolentino P: Haskell Avenue F: Van Nuys, CA E: P: x-21 E: Field Rep: Zach Grabinski P: E: MODEL/STYLE NO: FINISH: CONTENT: SG-ST-3 (VPCS) Bar Countertop & Backsplash Remanufacturing: Beige Microflec Project Stone: EcoQuartz Collection, Color: Khaki Eased Polished Edges Quartz Overall: 5-6 L x 26 D (Field verify all dimensions) Backsplash: 4 H Thickness: 2cm thick slab with 2cm laminated edge (overall 4cm edge) 1. Refer to image below for countertop and backsplash at bar counter. 2. Product to be of contract quality and suitable for commercial use. 3. Manufacturer to submit finish sample to IHG for written approval prior to production. 4. Stone top to be pre-cut prior to shipment. Field verify all dimensions. 5. From plan view, one side of top to be rounded. Refer to drawings. 6. Edge Detail: Outside edge to be eased and polished. 7. Backsplash: 4 backsplash of same material. 8. Refer to SG-102 for bar base. 9. Refer to drawings for further detail. 10. Refer to drawings for location. Not to Scale / Not for Color / Design Intent Only 10/15/11 7/13/12 1 SG-ST-3 (VPCS)

13 Vista, Spice, Chocolate, Sage Scheme Guestroom AREA: Bathroom Atlanta, GA Remanufacturing Project Stone, by Belstone Attn: Scott Deutsch Attn: Diane Tolentino P: Haskell Avenue F: Van Nuys, CA E: P: x-21 E: Field Rep: Zach Grabinski P: E: MODEL/STYLE NO: FINISH: CONTENT: SG-ST-4 (VPCS) Bath Quartz Countertop and Backsplash Remanufacturing: Beige Microflec Project Stone: EcoQuartz Collection, Color: Khaki Polished Outside Edges: Eased Edges at Cut-outs: 3/16 radius Quartz All Dimensions Must be Field Verified 2 cm thick slab with 2 cm laminated edge (overall edge: 4 cm). Refer to architectural drawings for overall dimensions. 1. Refer to image below for countertop finish. 2. Product to be of contract quality and suitable for commercial use. 3. Manufacturer to submit finish sample for IHG written approval prior to production. 4. Stone top to be pre-cut prior to shipment for under-mount sink. Follow sink cut-out template. Field verify all dimensions. (Dimensions to be verified with installer and sink installation template). 5. Refer to SG-152 for under-mount sink. Refer to SG-153 for faucet. 6. Edges: Eased at outside edge. 3/16 radius at cut-outs. All exposed edges to be polished. 7. Backsplash: 4 ½ high; length of vanity at back; depth of vanity at sidewall, minus thickness of backsplash at back. Thickness: 2cm. 8. Overhang: 1 overhang over cabinets (field verify). 9. Refer to drawings for further detail. 10. Refer to drawings for location. Not to Scale / Not for Color Design Intent Only 10/15/11 7/13/12 1 SG-ST-4 (VPCS)

14 AREA: Bathroom Atlanta, GA Mincey Marble Attn: Donna Mincey 4321 Browns Bridge Road Gainesville, GA P: P: E: PATTERN/STYLE: COLOR / FINISH: ACCENT BAND: SG-ST-5 (V) Tub Surround and Accessories TS-VS / 3x6 Vision Surround #2250 Solid White / Gloss Finish Refer to SG-T-2 (V) Panels: (1) 60 W x Ceiling Height panel, (2) 30 W x Ceiling Height panels Shampoo/Soap Shelf: (2) 7 x 7 x 9-7/8 1-1/2 All dimensions to be field verified 1. Refer to image below for tub surround finish. 2. Surround to be of contract quality and suitable for commercial use. 3. Grout/Etch line in mold: 1/8. This dimension to be included in overall dimension of surround. 4. Accent: Bottom of Accent tile to be 4-0 AFF. Align accent tile and surround at edges; no tile trim. 5. Corner Shampoo/Soap Shelf: (2) SS-04 shelves of same material/color as wall panels, to be mounted approximately 34 above tub deck (48 AFF), even with bottom of accent band (top of shelf to line up with surround grout line). 6. Installer to field verify all measurements and verify quantity needed for order. 7. Edge Detail: Schluter Strip to be installed at side edges. Refer to specification SG-TR-3 for Schluter strip. 8. Refer to SG-T-2 for Accent Band. 9. Refer to SG-155 for Tub Spec. 10. Refer to drawings/elevations for detail. 11. Refer to drawings for location. 10/01/11 8/7/12 1 SG-ST-5 (V)

15 AREA: Bathroom Atlanta, GA Not to Scale / Not for Color Design Intent Only 10/01/11 8/7/12 1 SG-ST-5 (V)

16 AREA: Bathroom Atlanta, GA Mincey Marble Attn: Donna Mincey 4321 Browns Bridge Road Gainesville, GA P: P: E: PATTERN/STYLE: COLOR / FINISH: ACCENT BAND: SG-ST-6 (V) Shower Surround and Soap Dishes TS-VS / 3x6 Vision Surround #2250 Solid White / Gloss Finish Refer to SG-T-3 Panels: (1) 60 W x Ceiling Height panel, (2) 32 W x Ceiling Height panels Shampoo/Soap Shelf: 7 x 7 x 9-7/8 1-1/2 H Corner Mount Foot Rest: 7 x 7 x 9-7/8 x 11 ¼ H All dimensions to be field verified 1. Refer to image below for shower surround finish. 2. Surround to be of contract quality and suitable for commercial use. 3. Shower to have a minimum inside clearance of 30 x 60, installed. 4. Grout/Etch line in mold: 1/8. This dimension to be included in overall dimension of surround. 5. Accent: Bottom of Accent tile to be 4-0 AFF. Align accent tile and surround at edges; no tile trim. 6. Corner Shampoo/Soap Shelf: (1) SS-04 shelf of same material/color as wall panels, to be mounted approximately 44 above top of Shower Base (48 AFF); even with bottom of accent band (top of shelf to line up with surround grout line). 7. Foot Rest: (1) FR-04 foot rest of same material and color as wall panels. To be mounted in same corner as shampoo shelf (corner opposite of shower controls), approximately 16 AFF to top of shelf. 8. Installer to field verify all measurements and verify quantity needed for order. 9. Edge Detail: Schluter Strip to be installed at side edges. Refer to specification SG-TR-3 for Schluter strip. 10. Refer to SG-T-3 for Accent Band. 11. Refer to SG-158 for Shower Pan spec, refer to SG-159 for Glass Shower Enclosure. 12. Refer to drawings/elevations for detail. 13. Refer to drawings for location. 10/01/11 8/7/12 2 SG-ST-6 (V)

17 AREA: Bathroom Atlanta, GA Design Intent Only / Not to Scale / Not for Color 10/01/11 8/7/12 2 SG-ST-6 (V)

18 AREA: Bathroom Atlanta, GA Mincey Marble Attn: Donna Mincey 4321 Browns Bridge Road Gainesville, GA P: P: F E: dmincey@minceymarble.com PATTERN/STYLE: COLOR / FINISH: SG-ST-7 (V) ADA Shower Surround and Accessories TS-VS / 3x6 Vision Surround #2250 Solid White / Gloss Finish Panels: (1) 62 W x Ceiling Height (2 pcs), (2) 37 W x Ceiling Height panels Shampoo Shelf: 7 x 7 x 9-7/8 1-1/2 H Soap Dish: 6-3/4 W x 3-1/2 D x 2 H Corner Mount Foot Rest: 7 x 7 x 9-7/8 x 11 ¼ H All dimensions to be field verified 1. Refer to image below for surround finish. 2. Shower must comply with current ADA regulations. 3. Surround to be of contract quality and suitable for commercial use. 4. Grout/Etch line in mold: 1/8. This dimension to be included in overall dimension of surround. 5. Accent: Bottom of Accent tile to be 4-0 AFF. Align accent tile and surround at edges; no tile trim. 6. Corner Shampoo Shelf: (1) SS-04 shelf of same material/color as wall panels, to be mounted approximately 41 above top of Shower Base (45 AFF) (top of shelf to line up with surround grout line). 7. Soap Dish: (1) SD-01 of same material/color as wall panels, to be mounted on back wall (see drawing for location). Soap dish to be installed so as not to obstruct use of the grab bar. 8. Foot Rest: (1) FR-04 foot rest of same material and color as wall panels, to be mounted in same corner as shampoo shelf (corner opposite of shower controls), approximately 16 AFF to top of shelf. 9. Installer to field verify all measurements and verify quantity needed for order. 10. Edge Detail: Schluter Strip to be installed at side edges. Refer to specification SG-TR-3 for Schluter strip. 11. Refer to SG-T-3 for Accent Band specification. 12. Refer to SG-180 for ADA Shower Pan spec 13. Refer to drawings/elevations for detail. 14. Refer to drawings for location. 10/01/11 8/6/12, 8/27/12 2 SG-ST-7 (V)

19 AREA: Bathroom Atlanta, GA Not to Scale / Not for Color Design Intent Only 10/01/11 8/6/12, 8/27/12 2 SG-ST-7 (V)

20 AREA: Bathroom Atlanta, GA Dal Tile Attn: John Hall 1630 Satellite Blvd. Duluth, GA P: E: MODEL/STYLE NO: FINISH/COLOR: GROUT: SG-T-1 (V) Vanity and Bathroom Floor Tile & Grout Kimona Silk Panda Black / P x 24 Field Tile Laticrete: #45 Raven 1. Refer to image below for floor tile. 2. Tile to be of contract quality and suitable for commercial use. 3. Per manufacturer, tile meets or exceeds the following requirements: Coefficient of Friction: Dry >0.7; Wet >0.6. ASTM C1028, ASTM C373: Moisture absorption < 0.5%, ASTM C Installer to verify quantity ordered. 5. Tile to be installed in a Staggered Running Bond Plank pattern. Refer to plans for tile direction. 6. Grout to be provided by General Contractor. No substitutions allowed. 7. Recommended grout joint: 1/8. Wall base grout lines to be lined up with floor grout lines. 8. Refer to SG-T-2 (V) for tile base at bath floor. 9. Refer to plans for location. Not to Scale / Not for Color / Design Intent Only 10/01/11 SG-T-1 (V)

21 AREA: Bathroom Atlanta, GA Dal Tile Attn: John Hall 1630 Satellite Blvd. Duluth, GA P: E: PATTERN/STYLE: COLOR / FINISH: GROUT: SG-T-2 (V) Accent Tile at Tub Surround Glass Reflections (1 x 1 Mosaic Tile) Twilight Blue / G404 5/16 Thick Custom Building Products - CEG-Lite; Epoxy Grout #381 Bright White 1. Refer to image below for accent tile. 2. Tile to be of contract quality and suitable for commercial use. 3. Refer to drawings/elevations for installation detail. 4. Bottom of Accent to be 48 AFF, and go to right & left edges of tub/shower surrounds. 5. Grout joint recommendation: 1/8. Grout to be provided by General Contractor. 6. Installer to verify quantity needed for order. 7. Refer to SG-ST-5 (V) for tub surround. Not to Scale / Not for Color / Design Intent Only 10/01/11 SG-T-2 (V)

22 AREA: Bathroom Atlanta, GA Dal Tile Attn: John Hall 1630 Satellite Blvd. Duluth, GA P: E: PATTERN/STYLE: COLOR / FINISH: GROUT: SG-T-3 (V) Accent Tile at Shower Surround Glass Reflections (1 x 1 Mosaic Tile) Twilight Blue / GR04 5/16 Thick Custom Building Products - CEG-Lite; Epoxy Grout #381 Bright White 1. Refer to image below for accent tile. 2. Tile to be of contract quality and suitable for commercial use. 3. Refer to drawings/elevations for installation detail. 4. Bottom of Accent to be 48 AFF, and go to right & left edges of tub/shower surrounds. 5. Grout joint recommendation: 1/8. Grout to be provided by General Contractor. 6. Installer to verify quantity needed for order. 7. Refer to SG-ST-6 (V) & SG-ST-7 (V) for shower surrounds. Not to Scale / Not for Color / Design Intent Only 10/01/11 SG-T-3 (V)

23 Vista, Spice, Chocolate, Sage Schemes Guestroom AREA: Guestroom Atlanta, GA Schluter Systems 194 Pleasant Ridge Road Plattsburgh, NY P: F: FINISH/COLOR: SG-TR-1 (VPCS) Transition Strip at Kitchen to Living Area (vinyl to carpet) Satin Anodized Aluminum Field verify length needed per area per property 1. Product to be of contract quality and suitable for commercial use. 2. Transition Strips required at flooring transitions. 3. General Contractor to determine size and type of transition strip needed for each application and submit to IHG for written approval prior to ordering. 4. Refer to Schluter Systems website for necessary transition strip needed: 5. General Contractor to determine quantity prior to ordering. 6. To be installed by General Contractor. 10/15/11 6/28/12 1 SG-TR-1 (VPCS)

24 Vista, Spice, Chocolate, Sage Schemes Guestroom AREA: Guestroom Atlanta, GA Schluter Systems 194 Pleasant Ridge Road Plattsburgh, NY P: F: FINISH/COLOR: SG-TR-2 (VPCS) Transition Strip at Bathroom to Bedroom (tile to carpet) Satin Anodized Aluminum Field verify length needed per area per property 1. Product to be of contract quality and suitable for commercial use. 2. Transition Strips required at flooring transitions. 3. General Contractor to determine size and type of transition strip needed for each application and submit to IHG for written approval prior to ordering. 4. Refer to Schluter Systems website for necessary transition strip needed: 5. General Contractor to determine quantity prior to ordering. 6. To be installed by General Contractor. 10/15/11 6/28/12 1 SG-TR-2 (VPCS)

25 Vista, Spice, Chocolate, Sage Scheme Guestroom AREA: Bathroom Atlanta, GA Schluter Systems 194 Pleasant Ridge Road Plattsburgh, NY P: F: STYLE / ITEM No.: FINISH/COLOR: SG-TR-3 (VPCS) Schluter Strip at Tub / Shower Wall Edge Schiene Radius R/AE80 Anodized aluminum; satin/mat Tolerance for 5/16" to 3/8"; field verify overall 1. Schluter strip to be installed at right and left tub/shower surround edge. Strip to be aligned with base and top of tub/shower surround. 2. Refer to image below for Schluter strip design intent. 3. Product to be of contract quality and suitable for commercial use. 4. General contractor to determine quantity prior to order. 5. To be installed by general contractor. 6. Refer to drawings for location. Not to Scale / For Design Intent Only 10/15/11 SG-TR-3 (VPCS)

26 Vista, Spice, Chocolate, Sage Schemes Guestroom AREA: Kitchen Atlanta, GA Schluter Systems 194 Pleasant Ridge Road Plattsburgh, NY P: F: STYLE / ITEM No.: FINISH/COLOR: SG-TR-4 (VPCS) Schluter Strip at Kitchen Backsplash Edge Schiene Radius R/AE80 Anodized aluminum; satin/mat Tolerance for 5/16" to 3/8"; field verify overall 1. Schluter strip to be installed at right and left backsplash edge. Strip to be aligned with countertop and top cabinets. Refer to image below for Schluter strip design intent. 2. Product to be of contract quality and suitable for commercial use. 3. General contractor to determine quantity prior to order. 4. To be installed by general contractor. 5. Refer to drawings for location. To be Wall Application; Not to Scale; For Design Intent Only 10/15/11 SG-TR-4 (VPCS)

27 Vista, Spice, Chocolate, Sage Schemes Guestroom AREA: Entry, Kitchen Atlanta, GA MANUFACTURER I: MANUFACTURER II: Mohawk Mats, Inc. Attn: Dawn Morris Attn: Jim Cave 405 Virgil Drive 37 Shuman Avenue Dalton, GA Stoughton, MA P: / P: / MATS-INC F: P: (Direct) E: dawn_morris@mohawkind.com F: E: jcave@matsinc.com SG-VF-1 (VPCS) Vinyl Flooring at Guest Suite Entry and Kitchen PRODUCT / COLLECTION: Mohawk: Mohawk Hard Surfaces Ultimate Step US07- X5006 Black Walnut, Exotic Collection 4 x 36 Planks Mats Inc.: Plank Collection W1036-W4, Shellbark Hickory 4 x 36 Planks THICKNESS: Approximately 1/8 (3.0 mm) 1. Refer to image below for flooring. 2. Product to be of contract quality and suitable for commercial use. 3. To be installed by General Contractor. Must follow manufacturer s installation directions. 4. Refer to Manufacturer for recommended adhesive. 5. Wear Layer: 20 Mil Wear. 6. Warranty: Varies by vendor. 7. Refer to plans for location. Not to Scale / Not for Color / Design Intent Only 10/15/11 7/13/12 1 SG-VF-1 (VPCS)

28 Vista, Spice, Chocolate, Sage Schemes Guestroom AREA: Entry, Kitchen Atlanta, GA MANUFACTURER I: Mannington Commercial Attn: Sean Finn 1844 US Highway 41 SE Calhoun, GA M: (Direct) P: (Factory) E: W: MANUFACTURER II: SG-VF-1 (VPCS) (Non-Adhesive Alternate) COLLECTION: STYLE: COLOR: Vinyl Flooring at Guest Suite Entry and Kitchen Nature s Path - Lock Solid Wenge Almost Black 4 x 36 Planks, Approximately.157 thick (4.0 mm) 1. Refer to image below for flooring. 2. Product to be of contract quality and suitable for commercial use. 3. To be installed by General Contractor. Must follow manufacturer s installation directions. 4. Wear Layer: Quantum Guard HP Urethane Aluminum Oxide Topcoat Cured by UV Process. Wear Layer Thickness:.020 inches (0.5 mm) 5. Warranty: Limited 10 year commercial. 6. Installation: LockSolid utilizes a proprietary and patented locking system that does not require adhesive. 7. Underlayment: Whisper 3N1 Underlayment is optional for all grades: above, on, and below. Whisper 3N1 Underlayment should not be used in heavy rolling load areas. 8. Refer to plans for location. Not to Scale / Not for Color / Design Intent Only 7/17/12 SG-VF-1 (VPCS) ALTERNATE

29 Vista, Spice, Chocolate, Sage Schemes Guestroom AREA: Entry, Kitchen Atlanta, GA Ceramic Technics Attn: Pace Adams 1298 Old Alpharetta Hwy Alpharetta, GA P x 218 Office Cel F E PAdams@ceramictechnics.com TYPE: STYLE: COLOR: SG-VF-1 (VPCS) (Tile Alternate for Vinyl Floor at Kitchen) Vinyl Flooring at Guest Suite Entry and Kitchen Porcelain Sassuolo Stone Wood Wenge SIZE: 6 x 24 GROUT: Mapei, 47 Charcoal-Anthracite-Carbon 1. Refer to image below for floor tile. 2. Refer to SG-B-1 for vinyl base. 3. Tile to be of contract quality and suitable for commercial use. 4. Per manufacturer, tile meets or exceeds the following requirements: Coefficient of Friction: Dry >0.6; Wet >0.6. ASTM C Installer to verify quantity ordered. 6. Floor to be prepped with crack isolation membrane prior to installing tile (sheet type recommended). 7. Tile to be installed in a Staggered Running Bond Plank pattern. 8. Grout to be provided by General Contractor. No substitutions allowed. 9. Recommended grout joint: 1/8 maximum. 10. Refer to plans for location. Design Intent / Not to Scale / Not for Color 8/25/12 SG-VF-1 (VPCS) ALTERNATE