Solid-sae Muli-funcional Timer Eigh operaing modes (H3DE-M) and four operaing modes (H3DE-S) cover a wide range of applicaions. Programmable conac enables he building of a self-holding relay circui (- 2 models). A wide ime seing range of 0.10 s o 120 h. Ordering Informaion Supply volage Conrol o oupu Model 24 o 230 VAC/DC Conac oupu: DPDT (ime-limi oupu SPDT and swichable SPDT (ime-limi insananeous)) Model Number Legend H3DE - 1 2 1. M: Muli-funcion ype S: Sandard ype 2. 2: DPDT 1: SPDT Muli-funcion ype H3DE-M2 Sandard ype H3DE-S2 Conac oupu: SPDT (ime-limi oupu SPDT) H3DE-M1 H3DE-S1 Accessories (Order Separaely) Mouning Track 50 cm (l) x 7.3 mm () PFP-50N 1 m (l) x 7.3 mm () PFP-100N 1 m (l) x 16 mm () PFP-100N2 End Plae PFP-M Spacer PFP-S 5
Specificaions General Iem H3DE-M2 H3DE-M1 H3DE-S2 H3DE-S1 Operaing mode A: ON-delay (Signal or ) B: Flicker OFF sar (Signal or ) B2: Flicker ON sar (Signal or ) C: Signal ON/OFF-delay D: Signal OFF-delay E: Inerval (Signal or ) G: Signal ON/OFF-delay J: One-sho (Signal or ) Terminal block Terminal screw ighening 0.98 N m max. {approx. 10 kgf cm max.} orque Clamps wo 2.5 mm 2 max. bar erminals wihou sleeves. Inpu ype Volage inpu --- A: ON-delay B2: Flicker ON sar E: Inerval J: One-sho Oupu ype Relay: DPDT Relay: SPDT Relay: DPDT Relay: SPDT Mouning mehod Aachmen Approved sandards Time Ranges DIN rack mouning Nameplae UL508, CSA 22.2 No.14 Conforms o EN61812-1 (VDE0435/P2021), IEC60664-1 (VDE0110) 4 kv/2, VDE0106/P100 Conforms o IEC60947-5-1 (AC-13; 250 V 5A/AC-15; 250 V 3 A/DC-13; 30 V 0.1 A) Conforms o EN50081-1 and EN50082-2 Time escaedspay scale display Time uni display sec min hrs 10 h x 0.1 0.1 o 1.2 s 0.1 o 1.2 min 0.1 o 1.2 h 1 o 12 h x 1 1 o 12 s 1 o 12 min 1 o 12 h 10 o 120 h Noe: When he main dial is se o 0 for all seings, he oupu will operae insananeously. Raings Raed supply volage (see noes 1 and 2) Operaing volage range rese 24 o 230 VAC/DC (50/60 Hz) 85% o 110% of raed supply volage Minimum power-off ime: 0.1 s Rese volage 2.4 VAC/DC max. consumpion H3DE-M1 AC: approx. 4.3 VA (2.2 W) a 230 VAC DC: approx. 0.7 W a 24 VDC (see noe 3) H3DE-M2 AC: approx. 4.8 VA (2.4 W) a 230 VAC DC: approx. 1.0 W a 24 VDC H3DE-S1 AC: approx. 2.7 VA (1.6 W) a 230 VAC DC: approx. 0.7 W a 24 VDC H3DE-S2 AC: approx. 3.2 VA (1.9 W) a 230 VAC DC: approx. 1.0 W a 24 VDC Volage inpu Max. permissible capaciance beween inpu lines (erminals and A2) : 2000 pf Load connecable in parallel wih inpus (erminals and A2) H-level: 20.4 o 253 VAC/DC L-level: 0 o 2.4 VAC/DC Conrol oupu Conac oupu: 5 A a 250 VAC wih resisive load (cosφ = 1) 5 A a 30 VDC wih resisive load (cosφ = 1) Ambien emperaure Operaing: 10 C o 55 C (wih no icing) Sorage: 25 C o 65 C (wih no icing) Ambien humidiy Operaing: 35% o 85% Noe: 1. DC ripple rae: 20% max. 2. Since an inrush curren of 0.25 A will occur when using he power supply volage a 24 VDC, pay careful aenion when urning on or off he power supply o he Timer wih a solid-sae oupu such as a sensor. 3. The power consumpion is for mode A afer he Timer couns he ime-up ime and for he AC inpu a 50 Hz. The power consumpion of he H3DE-M includes he inpu circui wih he and A1 erminals shor-circuied. 6
Characerisics Accuracy of operaing ime ±1% max. of FS (±1% ±10 ms max. a 1.2-s range) (see noe 1) Seing error ±10% ±50 ms max. of FS (see noe 1) Signal inpu ime 50 ms min. (see noe 1) Influence of volage ±0.5% max. of FS (±0.5% ±10 ms max. a 1.2-s range) Influence of emperaure ±2% max. of FS (±2%±10 ms max. a 1.2-s range) Insulaion resisance 100 MΩ min. a 500 VDC Dielecric srengh Beween curren-carrying meal pars and exposed non-curren-carrying meal pars: 2,000 VAC for 1 min. Beween conrol oupu erminals and operaing circui: 2,000 VAC for 1 min. Beween conacs of differen polariies: 2,000 VAC for 1 min. Beween conacs no locaed nex o each oher: 1,000 VAC for 1 min. Vibraion resisance Malfuncion: 0.5-mm single ampliude a 10 o 55 Hz Desrucion: 0.75-mm single ampliude a 10 o 55 Hz Shock resisance Malfuncion: 100 m/s 2 (approximaely 10G) Desrucion: 1,000 m/s 2 (approximaely 100G) Conac maerial AGNi+gold plaing (Use he G6RN-1 a 12 VDC.) Impulse wihsand volage 3 kv (beween power erminals) 4.5 kv (beween curren-carrying meal pars and exposed non-curren-carrying meal pars) Noise immuniy Square-wave noise generaed by noise simulaor (pulse widh: 100 ns/1 µs, 1-ns rise) ±1.5 kv Saic immuniy Malfuncion: 4 kv Desrucion: 8 kv Life expecancy Mechanical: 10 million operaions min. (under no load a 1,800 operaions/h) Elecrical: 100,000 operaions min. (5 A a 250 VAC, resisive load a 360 operaions/h) (see noe 2) EMC (EMI): EN50081-1 Emission Enclosure: EN55022 class B Emission AC Mains: EN55022 class B Harmonic Curren: EN61000-3-2 Volage Flucuaion and Flickering: EN61000-3-3 (EMS): EN50082-2 Immuniy ESD: EN61000-4-2:4 kv conac discharge (level 2) 8 kv air discharge (level 3) Immuniy RF-inerference from AM Radio Waves: ENV50140: 10 V/m (80 MHz o 1 GHz) (level 3) Immuniy RF-inerference from Pulse-modulaed Radio Waves: ENV50204: 10 V/m (900 ±5 MHz) (level 3) Immuniy Conduced Disurbance: ENV50141: 10 V (0.15 o 80 MHz) (level 3) Immuniy Burs: EN61000-4-4:2 kv power line (level 3) 2 kv I/O signal line (level 4) Enclosure raing IP30 (Terminal block: IP20) Weigh 120 g Noe: 1. Wih he H3DE-M, if he volage exceeds 26.4 VAC/DC, he following hold a signal OFF for C, D, and G modes: Accuracy of operaing ime: ±1% ±50 ms max. a 1.2-s range Seing error: ±10% +100/ 50 ms max. Signal inpu ime: 100 ms min. 2. For reference : A maximum curren of 0.15 A can be swiched a 125 VDC (cosφ=1). A maximum curren of 0.1 A can be swiched if L/R is 7 ms. In boh cases, a life of 100,000 operaions can be expeced. The minimum applicable load is 10 ma a 5 VDC (failure level: P). 7
Nomenclaure Time scale display window Time scale selecor (selec 0.1 or 1) Oupu indicaor (orange) (Li while Timer gives oupu.) Operaing mode selecor (selec a mode from A, B, C, B2, D, E, J, and G for he H3DE-M1/-M2, from A, E, J, and B2 for he H3DE-S1/S2) Nameplae for user use (20 x 5.4 mm whie panel) Time uni display window Time uni selecor (selec one from sec, min, hrs, and 10 h) Main dial (for seing a ime value) Operaing mode display window -on indicaor (green) (Li while he power is on.) (Fron View) Oupu Type Selecor Swich Seings Seing Oupu ype Time-limi oupu (erminal numbers 25, 26 and 28) (defaul seing) Oupu ype selecor swich for H3DE-M2/-S2 (defaul seing is ime-limi oupu) Insananeous oupu (erminal numbers 21, 22 and 24) (Boom View) Operaion Block Diagram H3DE-M1/-M2 AC (DC) inpu Zero seing deecion circui Time scale/ uni selecors Operaing mode selecor supply circui Oscillaion circui Couning circui Oupu circui Sar inpu Inpu circui Indicaor circui -ON indicaor Oupu indicaor 8
H3DE-S1/-S2 AC (DC) inpu Zero seing deecion circui Time scale/ uni selecors Operaing mode selecor supply circui Oscillaion circui Couning circui Oupu circui Indicaor circui -ON indicaor Oupu indicaor I/O Funcions Iem H3DE-M1/-M2 H3DE-S1/-S2 Inpu Sar Sars operaion. No inpu is available. Oupu Conrol oupu Oupus are urned ON according o designaed oupu mode when prese value is reached. (See noe.) Oupus are urned ON according o designaed oupu mode when prese value is reached. (see noe.) Noe: When he oupu ype selecor swich on he boom of he Timer is se o he insananeous side, he relay R2 (erminal numbers 21/25, 22/26, and 24/28) becomes an insananeous conac and urns ON/OFF in synchronizaion wih he changes in he power supply. Basic Operaion Seing of Selecor The selecors can be urned clockwise and counerclockwise o selec he desired ime uni, ime scale, or operaing mode. Each selecor has a snap mechanism ha secures he selecor a a given posiion. Se he selecor a a posiion a which i is secured. Do no se i midway beween wo securing posiions or a malfuncion could resul from improper seing. Selecion of Time Uni and Time Scale The desired ime uni (s, m, h, or 10h) can be displayed in he ime uni display window above he ime seing dial by urning he ime uni selecor locaed a he upper righ corner of he fron panel. Time scale (0.1 or 1) is seleced wih he ime scale selecor a he upper lef corner of he fron panel, i appears in he ime scale display window above he selecor. Time scale display window Time uni display window Operaing mode selecor Time scale selecor Operaing mode display window Time uni selecor Selecion of Operaing Mode The can be se o any one of he operaing modes A o J. Turn he operaing mode selecor wih a screwdriver unil he desired operaing mode (A, B, C, B2, D, E, J, or G for he H3DE-M and A, E, J, or B2 for he H3DE-S) appears in he operaing mode display window locaed below he selecor. 9
Timing Char Noe: 1. The minimum power rese ime is 0.1 s and he minimum signal inpu ime is 0.05 s. 2. The leer in he iming chars sands for he se ime and a means ha he period is less han he ime se. Operaing Timing char mode A: ON-delay a (A 1 and A 2 ) Basic operaion B: Flicker OFF sar Sar (B 1 and A 2 ) (see noe) Oupu relay: NC Oupu relay: NO (oupu indicaor) indicaor (A 1 and A 2 ) a a Sar Oupu For power-on operaion, impose volage o he Sar inpu. The Timer sars operaing a he momen he power is urned on. Sar inpu is invalid while he Timer is in operaion. Basic operaion B2: Flicker ON sar Sar (B 1 and A 2 ) (see noe) Oupu relay: NC Oupu relay: NO (oupu indicaor) indicaor (A 1 and A 2 ) a a Sar Oupu For power-on operaion, impose volage o he Sar inpu. The Timer sars operaing a he momen he power is urned on. Sar inpu is invalid while he Timer is in operaion. Basic operaion Sar (B 1 and A 2 ) (see noe) Oupu relay: NC Sar C: Signal ON/OFFdelay Oupu relay: NO (oupu indicaor) indicaor (A 1 and A 2 ) a a Oupu For power-on operaion, impose volage o he Sar inpu. The Timer sars operaing a he momen he power is urned on. Sar inpu is invalid while he Timer is in operaion. Sar (B 1 and A 2 ) (see noe) Basic operaion Oupu relay: NC Oupu relay: NO (oupu indicaor) Sar Oupu Noe: indicaor Sar inpu is invalid while he Timer is in operaion. The sar inpu of he H3DE-M1 or H3DE-M2 model is acivaed by applying a volage o and A2 erminals. The volage can be applied by urning on he conac beween and A1 (Refer o Terminal Arrangemen). 10
Operaing mode D: Signal OFF-delay (A 1 and A 2 ) Timing char a a a Basic operaion Sar (B 1 and A 2 ) (see noe) Oupu relay: NC Oupu relay: NO (oupu indicaor) indicaor Sar Oupu Sar inpu is valid and re-riggerable while he Timer is in operaion. E: Inerval a a (A 1 and A 2 ) Basic operaion G: Signal ON/OFFdelay J: One-sho oupu (ON delay) Noe: Sar (B 1 and A 2 ) (see noe) Oupu relay: NC Oupu relay: NO (oupu indicaor) indicaor (A 1 and A 2 ) Sar (B 1 and A 2 ) (see noe) Oupu relay: NC Oupu relay: NO (oupu indicaor) indicaor (A 1 and A 2 ) Sar (B 1 and A 2 ) (see noe) Oupu relay: NC Oupu relay: NO (oupu indicaor) indicaor Approx. 1±0.6 s (fixed) a a Approx. 1±0.6 s (fixed) Approx. 1±0.6 s (fixed) Sar Oupu For power-on operaion, impose volage o he Sar inpu. The Timer sars operaing a he momen he power is urned on. Sar inpu is valid and re-riggerable while he Timer is in operaion. Sar Oupu Sar Oupu Basic operaion Sar inpu is valid and re-riggerable while he Timer is in operaion. Basic operaion Approx. 1±0.6 s (fixed) For power-on operaion, impose volage o he Sar inpu. The Timer sars operaing a he momen he power is urned on. Sar inpu is valid and re-riggerable while he Timer is in operaion. The sar inpu of he H3DE-M1 or H3DE-M2 model is acivaed by applying a volage o and A2 erminals. The volage can be applied by urning on he conac beween and A1 (Refer o Terminal Arrangemen). 11
Dimensions Noe: All unis are in millimeers unless oherwise indicaed. Terminal block (black) Surface color: Ligh gray 5Y7/1 (OMRON) Oupu ype selecor swich (defaul seing: Time-limi oupu) Terminal block (black) Insallaion Terminal Arrangemen H3DE-M1 H3DE-M2 H3DE-S1 H3DE-S2 A1 15 R1 15 18 16 18 16 A2 ------------ A1 15 25 / 21 R1 15 (see noe 1) R2 25/21 18 16 28 / 26 24 / 22 28 / 24 26 / 22 18 16 A2 ------------ A1 15 R1 15 18 16 18 16 A2 A1 15 25 / 21 R1 15 (see noe 1) R2 25/21 18 16 28 / 26 24 / 22 28 / 24 26 / 22 18 16 A2 (see noe 2) (see noe 2) (see noe 2) (see noe 2) Noe: 1. The relay R2 can be se o eiher insananeous or ime-limi conac using he swich locaed on he boom of he Timer. 2. DC supply volage does no require he designaion of polariy. 3. The conac symbol for he H3DE is indicaed wih because i offers muliple operaing modes and is differen from he delayed conac for convenional imers. 12
Inpu Connecions The inpus of he H3DE-M1/-M2 are volage (volage imposiion or open) inpus. No-conac Inpu (Connecion o PNP oupu sensor.) Sensor No-conac Inpu (Connecion o NPN oupu sensor.) Timer Conac Inpu Timer (+) 24 VDC ( ) A 2 Timer (+) 24 VDC ( ) Sar A 2 A 1 A 1 Sar A 2 A 1 Operaes wih PNP ransisor ON Sensor Operaes wih NPN ransisor ON Operaes wih relay ON Volage Inpu Signal Levels No-conac inpu Conac inpu 1. Transisor ON Residual volage: 1 V max. (Volage beween erminals B 1 and A 2 mus be more han he raed H-level volage (20.4 VDC min.).) 2. Transisor OFF Leakage curren: 0.01 ma max. (Volage beween erminals B 1 and A 2 mus be less han he raed L-level volage (2.4 VDC max.).) Use conacs ha can adequaely swich 0.1 ma a each volage o be imposed. (When he conacs are ON or OFF, volage beween erminals B 1 and A 2 mus be wihin he following ranges: When conacs are ON: 20.4 o 253 VAC/DC When conacs are OFF: 0 o 2.4 VAC/DC 13