Tension-Clamp Ulra-Slim Signal Condiioners M6S Series FUNCTION MODULE (PC programmable) Funcions & Feaures Mainenance-free ension clamp connecion Single inpu filer and funcion module 12 ypes of funcions are PC programmable 5.9-mm wide ulra-slim design Low profile allows he M6S module mouned in a 12-mm deep panel High-densiy mouning Power and saus indicaor LEDs 5.9 (.23) 94 (3.7) Volage V2: Range -1 1 V DC V3: Range -5 5 V DC (Configuraor sofware is used o change oupu over he described range of he seleced suffix code. For changing beween suffix codes, se he Oupu Range Selecor on he side of uni before sofware adjusmen.) POWER DC Power R: 24 V DC (Operaional volage range 24 V ±1 %, ripple 1 %p-p max.) [3] OPTIONS (muliple selecions) Sandards & Approvals blank: CE marking /UL: UL approval, CE marking Oher Opions blank: none /Q: Opion oher han he above (specify he specificaion) 12 (4.2) mm (inch) [1][2] R[3] ORDERING INFORMATION Code number: M6SXF1-[1][2]-R[3] Specify a code from below for each [1] hrough [3]. (e.g. M6SXF1-Z1Z1-R/UL/Q) Inpu range (e.g. 4 2 ma DC) Oupu range (e.g. 4 2 ma DC) Specify he specificaion for opion code /Q (e.g. /C1/SET) [1] Curren Z1: Range 5 ma DC (Inpu resisance 24.9 Ω) Volage S1: Range -1 1 mv DC (Inpu resisance 1 MΩ min.) S2: Range -1 1 V DC (Inpu resisance 1 MΩ min.) (Configuraor sofware is used o change he inpu ype and precise range.) [2] Curren Z1: Range 2 ma DC SPECIFICATIONS OF OPTION: Q (muliple selecions) COATING (For he deail, refer o M-Sysem's web sie.) /C1: Silicone coaing /C2: Polyurehane coaing EX-FACTORY SETTING /SET: Prese according o he Ordering Informaion Shee (No. ESU-7847) FUNCTIONS PC Configuraor Sofware is used o program he funcion. Filer, linearizaion and limier funcions can be combined. Filer / Lag Moving average oupu Dead ime compuing Delay buffer (firs order lag) Lead ime compuing Ramp buffer Linearizaion User s able linearizaion Invered oupu Square roo exracion (orifice, venuri) X 2 (Palmer-Bowlus flume, Parshall flume) X 5/2 (riangular or v-noch weir) X 3/2 (recangular weir) Limier High / Low limi Facory defaul funcion seing Filer: Moving average (H =.1, N = 1, U =, L = ) M6SXF1 SPECIFICATIONS ES-7987 Rev.8 Page 1/6
Linearizaion: None Limier: Low limi = -2 %, High limi = 12 % S1: 1 mv DC S2: 1 5 V DC RELATED PRODUCTS PC configuraor sofware (model: M6CFG) Downloadable a M-Sysem s web sie. A dedicaed cable is required o connec he module o he PC. Please refer o he inerne sofware download sie or he users manual for he PC configuraor for applicable cable ypes. GENERAL SPECIFICATIONS Connecion Inpu and oupu: Tension clamp Power inpu: Via he Insallaion Base (model: M6SBS) or Tension clamp Applicable wire size:.2 o 2.5 mm 2, sripped lengh 8 mm Housing maerial: Flame-resisan resin (black) Isolaion: Inpu o oupu o power Overrange oupu: -2 12 % (Negaive curren oupu is no available.) Zero adjusmen: -2 o 2 % (PC programming) Span adjusmen: 98 o 12 % (PC programming) Power LED: Green ligh urns on when he power is supplied. Saus indicaor LED: Orange LED; Blinking paerns indicae differen operaing saus of he ransmier. Programming: Downloaded from PC; inpu ype and range, oupu ype and range, zero and span, funcion ype and parameers, ec. For deailed informaion, refer o he users manual for he PC configuraor. Configuraor connecion: 2.5 dia. miniaure jack; RS-232-C level SPECIFICATIONS DC Curren: Inpu resisor incoporaed (If no specified, he inpu range is 4 2 ma DC.) Inpu range: 5 ma DC Minimum span: 2 ma inpu range provided ha he minimum span is mainained. DC Volage Code S1 (narrow spans) Inpu range: -1 1 mv DC Minimum span: 1 mv Code S2 (wide spans) Inpu range: -1 1 V DC Minimum span: 1 V inpu range provided ha he minimum span is mainained. If no specified, he inpu range is shown below. SPECIFICATIONS DC Curren Oupu range: 2 ma DC Conformance range: 2.4 ma DC Minimum span: 1 ma oupu range provided ha he minimum span is mainained. Load resisance: Oupu drive 11 V max. (e.g. 4 2 ma: 55 Ω [11 V 2 ma]) If no specified, he oupu range is 4 2 ma DC. DC Volage Code V2 (wide spans) Oupu range: -1 1 V DC Conformance range: -1.4 1.4 V DC Minimum span: 1 V Code V3 (narrow spans) Oupu range: -5 5 V DC Conformance range: -5.2 5.2 V DC Minimum span:.5 V oupu range provided ha he minimum span is mainained. Load resisance: Oupu drive 1 ma max. (e.g. 1 5 V: 5 Ω [5 V 1 ma]) If no specified, he oupu range is shown below. V2: 1 V DC V3: 1 5 V DC INSTALLATION Power consumpion: Approx..5 W Operaing emperaure: -2 o 55 C (-4 o 131 F) Operaing humidiy: 3 o 9 %RH (non-condensing) Mouning: Insallaion Base (model: M6SBS) or DIN rail Weigh: 65 g (2.3 oz) PERFORMANCE in percenage of span Overall accuracy I/O gain 1: Inpu accuracy Oupu accuracy I/O gain > 1: [Inpu accuracy Oupu accuracy] I/O gain Inpu accuracy*: (% of max. inpu range) -1 1 mv : ±.1 % -1 1 V : ±.1 % 5 ma : ±.2 % Oupu accuracy*: ±.4 % of max. oupu range *Inversely proporional o he span. See CALCULATION EXAMPLES OF OVERALL ACURACY. Temp. coefficien: ±.1 %/ C (±.6 %/ F) of max. span M6SXF1 SPECIFICATIONS ES-7987 Rev.8 Page 2/6
Response ime:.5 sec. ( 9 %) wihou any funcion seing Line volage effec: ±.1 % over volage range Insulaion resisance: 1 MΩ wih 5 V DC Dielecric srengh: 2 V AC @1 minue (inpu o oupu o power o ground) CALCULATION EXAMPLES OF OVERALL ACCURACY [Example] Inpu Type -1 1 V, Inpu Range 1 5 V, Oupu Type -5 5 V, Oupu Range 1 5 V Inpu accuracy = Max. Inpu Range (2 V) Span (4 V).1 % =.5 % Oupu accuracy = Max. Oupu Range (1 V) Span (4 V).4 % =.1 % Accuracy= ±.15 % STANDARDS & APPROVALS EU conformiy: EMC Direcive EMI EN 61-6-4 EMS EN 61-6-2 RoHS Direcive EN 5581 Approval: UL/C-UL nonincendive Class I, Division 2, Groups A, B, C, and D (ANSI/ISA-12.12.1, CAN/CSA-C22.2 No.213) UL/C-UL general safey requiremens (UL 611-1, CAN/CSA-C22.2 No.611-1) EXTERNAL VIEW FRONT VIEW (wih he cover open) SIDE VIEW 5 6 7 8 Power LED Saus Indicaor LED Configuraor Jack SW1 Oupu Range Selecors ON SW1 1 2 3 4 5 6 7 8 OFF 1 2 3 4 The DIP swich seing is required o selec oupu ypes before seing a precise oupu range using PC Configuraor Sofware (model: M6CFG). Refer o he insrucion manual for deailed procedures. M6SXF1 SPECIFICATIONS ES-7987 Rev.8 Page 3/6
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS uni: mm (inch) SCREWDRIVER * INSERTION ANGLE : approx. 35 WIRE INSERTION ANGLE : approx.35 TEST PROBE max. 2 (.8) dia. 5 6 7 8 DIN RAIL HOOK DIN RAIL 35mm wide 94 (3.7) 5.9 (.23) 1 2 3 4 SCREWDRIVER INSERTION ANGLE : approx. 4 [.5 (.2)] 12 (4.2) When mouning, no exra space is needed beween unis. *Use a minus screwdriver: ip widh 3.8 mm max., ip hickness.5 o.6 mm SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM CURRENT (Z1) VOLTAGE (S1, S2) CONFIGURATOR 24.9Ω 1 2 3 4 JACK Low Drif Amplifier STATUS IND. LED Digial Compuaion Isolaion DIP SW Oupu Driver POWER LED 5 6 7 8 CONNECTOR POWER POWER M6SXF1 SPECIFICATIONS ES-7987 Rev.8 Page 4/6
FUNCTIONS MOVING AVERAGE The module samples inpu signals every H seconds and, excluding U numbers of highes-value samples and L numbers of lowes-value samples, oupus proporionally o he average of he res [N (U L)] of sampled daa. When a new inpu is sampled afer anoher H seconds, i gives up he oldes sample and calculaes a new average including he laes sample and oupus proporionally. When he number of samples o be calculaed equals or less, i oupus an error. H: Sampling cycle (.1 o 1. seconds) N: Number of samples o be calculaed (1 o 128) U: Number of highes-value samples o be cu off ( o 127) L: Number of lowes-value samples o be cu off ( o 127) H N numbers N numbers average H DEAD-TIME COMPUTING The module does no respond o an inpu signal for a prese dead-ime* duraion. In addiion, wih adjusing a ime consan T, i generaes a firs order lag oupu afer he dead-ime. Sep inpu wih dead-ime e HNs X (s) = X1 (s) 1 Ts where X1: Inpu X: Oupu Dead ime = H x N (s) H x N H: Sampling cycle (.1 o 1. seconds) N: Numbers of samples o be calculaed (1 o 128) T: Time consan (. or.5 o 1. seconds) Sep inpu wih dead-ime plus ime consan *Oupu is refreshed every sampling cycle. The response ime may be delayed by 1 cycle a he maximum. H x N T DELAY BUFFER The module generaes a firs order lag oupu. 1 X (s) = X1 (s) 1 Ts where X1: Inpu X: Oupu T: Time consan (.5 o 1. seconds) Sep inpu wih ime consan T M6SXF1 SPECIFICATIONS ES-7987 Rev.8 Page 5/6
LEAD-TIME COMPUTING The module operaes a lead-ime equaion. X (s) = (1 Ts) X1 (s) where X1: Inpu X: Oupu T: Lead-ime consan (.5 o 1. seconds) Sep inpu wih lead-ime consan T RAMP BUFFER The modules oupu does no change faser han a prese maximum rae, posiive CP and negaive CN, no maer how fas is inpu changes. CP: Maximum rae of posiive oupu change (. o 2.%/second) CN: Maximum rae of negaive oupu change (. o 2.%/second) Sep inpu wih rae-of-change limis CP CN HIGH / LOW LIMIT The oupu does no go above he prese high limi or below he prese low limi. High and Low limis are independenly selecable. USER S TABLE LINEARIZATION The inpu is convered ino a linearized oupu according o he user specified segmen daa able, defined wih pairs of X (inpu) and Y (oupu) values. 2 o 11 segmen poins can be specified. INVERTED The oupu is inversely proporional o he inpu. X = 1 X1 where X1: Inpu (%) X: Oupu (%) SQUARE ROOT EXTRACTION (orifice, venuri) The oupu is square roo of inpu. X = 1 X1 X 2 (Palmer-Bowlus flume, Parshall flume) X = X1 2 / 1 where X1: Inpu (%) X: Oupu (%) X 5/2 (riangular or V-noch weir) X = X1 5/2 / 1 where X1: Inpu (%) X: Oupu (%) X 3/2 (recangular weir) X = X1 3/2 / 1 where X1: Inpu (%) X: Oupu (%) OTHER FUNCTIONS The low-end cuou poin can be se wihin. 99.9999% of inpu signal. where X1: Inpu (%) X: Oupu (%) Specificaions are subjec o change wihou noice. M6SXF1 SPECIFICATIONS ES-7987 Rev.8 Page 6/6