Specificaions and descripion PRKL 3B Laser rero-reflecive phooelecric sensor wih polarisaion filer Dimensioned drawing en 08-2011/04 50105363 2 khz 0 3m 10-30 V DC Polarized rero-reflecive phooelecric sensor wih auocollimaion principle Small and compac consrucion wih robus plasic housing, proecion class IP 67 for indusrial applicaion Push-pull oupu wih ligh/dark swiching via each-in buon High swiching frequency for deecion of fas evens and small pars Easy adjusmen via lockable each buon or each inpu Laser class 1 A B C D E Green indicaor diode Yellow indicaor diode Opical axis Teach buon Aachmen sleeve We reserve he righ o make changes DS_PRKL3B_en.fm Accessories: (available separaely) U L US C LISTED IEC 60947... IEC 60947... IP 67 Mouning sysems (BT 3 ) Cable wih M8 or M12 connecor (K-D ) Reflecors Reflecive apes Elecrical connecion Plug connecion, 4-pin Plug connecion, 3-pin Cable, 4-wire Leuze elecronic GmbH + Co. KG In der Braike 1 D-73277 Owen Tel. +49 (0) 7021 573-0 info@leuze.de www.leuze.com PRKL 3B - 08
Specificaions (no valid for RKL 3B/6.22!) Opical daa Typ. op. range limi (MTKS 50 x 50) 1) 0 3m Operaing range 2) see ables Ligh beam characerisic collimaed, 3mrad Ligh spo diameer approx. 2mm a ligh beam gae Ligh source 3) laser (pulsed) Wavelengh 655nm (visible red ligh, polarized) Max. oupu power 0.29mW Pulse duraion 5.5μs Timing Swiching frequency 2,000Hz Response ime 0.25ms Delay before sar-up 300ms Elecrical daa Operaing volage U 4) B 10 30VDC (incl. residual ripple) Residual ripple 15% of U B Open-circui curren 15mA Swiching oupu 5) /6.22 1 push-pull swiching oupu pin 4: PNP ligh swiching, NPN dark swiching pin 2: each inpu /6.2 -S8.3 1 push-pull swiching oupu pin 4: PNP ligh swiching, NPN dark swiching /4.28 1 PNP swiching oupu, ligh swiching, pin 2: acivaion inpu Funcion characerisics ligh/dark reversible Signal volage high/low (U B -2V)/ 2V Oupu curren max. 100mA Operaing range seing via each-in Indicaors Green ready Yellow ligh pah free Yellow, flashing ligh pah free, no performance reserve 6) Mechanical daa Housing 7) plasic (PC-ABS); 1 aachmen sleeve, nickel-plaed seel Opics cover plasic (PMMA) Weigh wih connecor: 10g wih 200mm cable and connecor: 20g wih 2m cable: 50g Connecion ype 2m cable (cross secion 4x0.20mm²), connecor M8 meal, 0.2m cable wih connecor M8 or M12 Environmenal daa Ambien emp. (operaion/sorage) -10 C +55 C 8) / -30 C +70 C Proecive circui 9) 2, 3 VDE safey class III Proecion class IP 67 Laser class 1 (in accordance wih EN 60825-1) Sandards applied IEC 60947-5-2 Cerificaions CDRH 21 CFR 1040, UL 508 4) Opions Teach-in inpu/acivaion inpu Transmier acive/no acive 8V/ 2V Acivaion/disable delay 1ms Inpu resisance 30kΩ 1) Typ. operaing range limi: max. aainable range wihou performance reserve 2) Operaing range: recommended range wih performance reserve 3) Average life expecancy 50,000h a an ambien emperaure of 25 C 4) For UL applicaions: for use in class 2 circuis according o NEC only 5) The push-pull swiching oupus mus no be conneced in parallel 6) Display "no performance reserve" as yellow flashing is only available in sandard each seing 7) Paen Pending Publ. No. US 7,476,848 B2 8) Wihou mouning max. +50 C, wih screw mouning on meal par up o +55 C permissible 9) 2=polariy reversal proecion, 3=shor-circui proecion for all ransisor oupus Tables Reflecors Operaing range 1 MTKS 50x50 0 2.0m 2 MTKS 20x30 0 1.6m 3 MTKS 20x40.1 0 1.0m 4 Tape6 50x50 0 1.0m 5 Tape4 25x20 0 0.3m 1 0 2,0 3,0 2 0 1,6 2,2 3 0 1,0 1,5 4 0 1,0 1,4 5 0 0,3 0,4 Operaing range [m] Typ. operaing range limi [m] MTKS = micro riple, screw ype Remarks Approved purpose: This produc may only be used by qualified personnel and mus only be used for he approved purpose. This sensor is no a safey sensor and is no o be used for he proecion of persons.. Mouning sysem: ➀ ➁ ➂ Remarks Adaper plae: BT 3.2 (par no. 50103844) for alernae mouning on 25.4mm hole spacing (Omron E3Z, Sick W100 ) ➀ =BT3 (par no. 50060511) ➁+➂ =BT3.1 1) (par no. 50105585) ➀+➁+➂ =BT3B (par no. 50105546) 1) Packaging uni: PU = 10 pcs. PRKL 3B - 08 2011/04
Laser rero-reflecive phooelecric sensor wih polarisaion filer Order guide Selecion able Equipmen Oupu 1 (OUT 1) 1) Special ype, prior o use, consul wih he head office! 2) Preseing Order code push-pull swiching oupu, ligh swiching 2) 2) 2) 2) 2) 2) 2) configurable dark swiching 2) ligh swiching PNP ransisor oupu dark swiching Inpu each inpu (IN) acivaion inpu Connecion cable 2,000mm 4-wire M8 connecor, meal 3-pin M8 connecor, meal 4-pin 200mm cable wih M8 connecor 3-pin 200mm cable wih M8 connecor 4-pin 200mm cable wih M12 connecor 4-pin Configuraion each-in via buon (lockable) and each inpu each-in via buon General informaion The laser rero-reflecive phooelecric sensors PRKL 3B/ have an opimized ligh beam propagaion in he ypical range of applicaion of 0 1m (no o be confused wih he operaing range, which is 0 3m in combinaion wih a reflecor MTKS 50x50). This permis he reliable recogniion of he smalles of pars or he posiioning of objecs wih maximum precision across he enire area. The sensor is consruced on he basis of he auocollimaion principle, i.e., ligh being ransmied and ligh being received propagae along he same ligh axis. This permis he phooelecric sensor o be insalled direcly behind small holes or diaphragms. The smalles permissible diaphragm diameer for secure funcioning is 3mm. PRKL 3B/6.22 Par No. 50104705 PRKL 3B/6.22-S8 Par No. 50104706 PRKL 3B/6D.22-S8 Par No. 50106475 PRKL 3B/6.22, 200-S8 Par No. 50104707 PRKL 3B/6.22, 200-S12 Par No. 50105764 PRKL 3B/6.2-S8.3 Par No. 50109484 PRKL 3B/6.2, 200-S8.3 on reques PRKL 3B/4.28-S8 on reques RKL 3B/6.22 1) Par No. 50106854 Diaphragm diameer 3mm Typ. applicaion range 0 1m The achievable resoluion depends significanly on he uni's configuraion. Depending on he each mode, he following values are possible: Seing Deecion from objec size 1) Sensor swiches a a ligh occlusion of max. operaing range (facory seing) 1,5mm 50% normal sensor sensiiviy (sandard eaching) 1mm 25% maximum sensor sensiiviy (dynamic eaching) 0.1 0.2mm 5% 1) All specificaions are ypical values and may vary by a small amoun for each uni. For safey reasons, he laser ransmier is equipped wih a monior, which auomaically swiches off he ransmier in case of a componen defec. In case of failure, he yellow flashes rapidly and he green is off. The sae is irreversible and he sensor mus be exchanged. Leuze elecronic GmbH + Co. KG In der Braike 1 D-73277 Owen Tel. +49 (0) 7021 573-0 PRKL 3B - 08 info@leuze.de www.leuze.com
Sensor adjusmen (each) via each buon Prior o eaching: Clear he ligh pah o he reflecor! The device seing is sored in a fail-safe way. A reconfiguraion following volage inerrupion or swich-off is hus no required. Sandard eaching for average sensor sensiiviy Press each buon unil boh s flash simulaneously. Release each buon. Ready. Afer sandard eaching, he sensor swiches for objecs wih a minimum size of 1mm (see able under "General Informaion"). If boh s flash rapidly afer he eaching even, a eaching error has happened. Please check he alignmen of he ligh beam ono he reflecor and carry ou anoher eaching even. 2 7s green simulaneously flashing a 3Hz yellow Teaching for maximal sensor sensiiviy (dynamic eaching) Press each buon unil boh s flash alernaingly. Sensor remains in eaching mode even afer he each buon has been released. Move some objecs hrough he ligh pah or swing a single objec slowly back and forh hrough he ligh pah. Briefly press he each buon o erminae he each even. Ready. Afer eaching for maximum sensor sensiiviy, he sensor swiches for objecs wih a minimum size of 0.1 0.2mm (see able under "General Informaion"). If boh s flash rapidly afer he eaching even, a eaching error has happened. Please check he alignmen of he ligh beam ono he reflecor and carry ou anoher eaching even. 7 12s green alernaingly flashing a 3Hz yellow PRKL 3B - 08 2011/04
Laser rero-reflecive phooelecric sensor wih polarisaion filer Teaching for maximum operaing range (facory seing a delivery) Prior o eaching: Cover he ligh pah o he reflecor! Procedure as for sandard eaching. green yellow 2 7s simulaneously flashing a 3Hz Adjusing he swiching behavior of he swiching oupu ligh/dark swiching Press each buon unil he green flashes. The yellow displays he curren seing of he swiching oupu: ON = oupu swiches on ligh OFF = oupu swiches on dark Coninue o press he each buon in order o change he swiching behavior. Release each buon. Ready. >12s green flashes a 3Hz yellow ON = ligh swiching OFF = dark swiching Leuze elecronic GmbH + Co. KG In der Braike 1 D-73277 Owen Tel. +49 (0) 7021 573-0 PRKL 3B - 08 info@leuze.de www.leuze.com
Locking he each buon via he each inpu A saic high signal ( 4ms) a he each inpu locks he each buon on he device if required, such ha no manual operaion is possible (e.g., proecion from erroneous operaion or manipulaion). If he each inpu is no conneced or if here is a saic low signal, he buon is unlocked and can be operaed freely. Sensor adjusmen (each) via each inpu The following descripion applies o PNP swiching logic! 2V (U B -2V) Prior o eaching: Clear he ligh pah o he reflecor! The device seing is sored in a fail-safe way. A reconfiguraion following volage inerrupion or swich-off is hus no required. Sandard eaching for average sensor sensiiviy Afer he delay before sar-up ( 300ms) has elapsed, he each buon on he device can be operaed. The each buon is disabled afer he 1s edge. Teach1 4... 1000 ms Sandard each: Teach1 = 4 1,000ms Afer abou 4ms, he curren each value is applied, each process compleed. The buon remains disabled unil he nex signal change. Teach buon may now be operaed again. Quick sandard each 4 ms 4 ms 4 ms shores eaching duraion for sandard eaching: approx. 12ms Afer sandard eaching, he sensor swiches for objecs wih a minimum size of 1mm (see able under "General Informaion"). PRKL 3B - 08 2011/04
Laser rero-reflecive phooelecric sensor wih polarisaion filer Teaching for maximal sensor sensiiviy (dynamic eaching) Afer he delay before sar-up ( 300ms) has elapsed, he each buon on he device can be operaed. The each buon is disabled afer he 1s edge. Teach 1000... 2000 ms Teach for maximum sensor sensiiviy: Teach = 1,000 2,000ms Boh s flash a 3Hz as long as high signal is presen Sensor remains in each mode as long as he high signal is presen. Boh s flash alernaingly a 3Hz. Move some objecs hrough he ligh pah or swing a single objec slowly back and forh hrough he ligh pah. Afer abou 4ms, he curren each value is applied and he each process compleed. The each buon can again be operaed. In he even of a each error (e.g. no each objec or a each objec which is oo small or oo ransparen is moved hrough he ligh pah), he wo s flash a he same rae. Check he sysem, repea he each process, if necessary use a larger or less ransparen each objec. Afer eaching for maximum sensor sensiiviy, he sensor swiches for objecs wih a minimum size of 0.1 0.2mm (see able under "General Informaion"). Adjusing he swiching behavior of he swiching oupu ligh/dark swiching Teach Oupu 2000... 3000 ms p ligh 4... 1000 ms Teach Oupu 2000... 3000 ms p dark 1000... 2000 ms Afer he delay before sar-up ( 300ms) has elapsed, he each buon on he device can be operaed. The each buon is disabled afer he 1s edge. Seing he swiching behavior of he swiching oupu: Teach Oupu = 2,000 3,000ms Swiching oupu swiches on ligh: p ligh = 4 1,000ms Swiching oupu swiches on dark: p dark = 1,000 2,000ms The buon remains disabled unil he nex signal change. Leuze elecronic GmbH + Co. KG In der Braike 1 D-73277 Owen Tel. +49 (0) 7021 573-0 PRKL 3B - 08 info@leuze.de www.leuze.com
PRKL 3B - 08 2011/04