How to build a hockey stick bench
|
|
- Norma Foster
- 5 years ago
- Views:
Transcription
1 How to build a hockey stick bench The hockey stick bench is a great piece of fully functional furniture that doesn t require a lot of sticks. Composite sticks are really strong, so even if you space them out, they make a good seat. This design will give plans for using sticks for the legs and pucks for the feet, adding an extra cool factor. Though the hockey stick bench legs are at an angle with this design, it can be easily modified for the legs to be perpendicular to the seat, making it simpler to build. What you ll need Miter Saw Router or Mill Drill Allen wrenches Wrench set Bubble level 4 bar clamps (2 greater than 3 ft) Several 2 spring clamps Glue 14 hockey sticks 8: 5/16-18 Shoulder Bolt, 2.75 long 8: 5/16 Washer 8: 5/16 Nuts 4: #10-32 Shoulder Bolt, 2.5 long 4: #10 Washer 4: #10-32 Nuts 8: #6 1.5 Sheet metal screw 27: # Sheet metal screw 4: 3 Mending plates (if reinforcement desired) 16: #8 1/2 socket cap screws (if reinforcement desired) Build the seat The first order of business is the seat. You ll want to use only those sticks that are greater than 41.5 in length. Don t try to glue or attach broken sticks together to try to get the length right. It s for a bench, so you don t want to sit down and have the seat break! First, cut nine sticks to 41.5 length. Then cut three seat attachment pieces to in length and in two of them, drill holes of about 7/32 in diameter 3.75 inches from either end. Choose four of the nine seat slat sticks and drill 3/8 holes in the locations shown in the image below. (Note: image does not show the other seven sticks.)
2 Using spare sticks or other material as spacers, clamp all nine of the 41.5 sticks together where two of the sticks with the holes should be on both outer edges. Secure the seat attachment pieces on the bottom of each stick as shown in the images below using #6, 1.25 sheet metal screws ensuring the two bench attachment pieces with holes are on the outside. For the #6 screws, I recommend drilling a pilot hole with a 7/64 bit to make driving the screws much easier. The spare sticks are highlighted orange in the image below.
3 Go ahead and remove the spare sticks in between, and you ve got a bench seat! Building the legs and leg supports The three pieces for a single leg are shown in the image below: an approximately 18 leg, a 10 13/16 support piece and a small 4.5 support piece. You ll have to make four of all three pieces. Take the main leg and the longer support pieces and insert them between the first two bench slats as shown below. The leg face with the 10 degree angle cut should face down on the bench so the leg angles outward. The support piece should have the 45 degree cut face down between the bench slats, putting the 55 degree cut against the leg.
4 Using two 5/16 to shoulder bolts, bolt the legs and the supports pieces to the bench. Be sure to use a washer behind the bolt head and nut. Next, drill a #6 1.5 sheet metal screw and a # sheet metal screw from the support piece into the chair leg. The 1.5 screw should be on the inside, since it has farther to travel. The drawing below summarizes the connections that should be made for each leg at this step. Repeat this process for all four legs.
5 First, measure the distance between legs on a short side of the bench down the seat starting at the outer edge of each leg. It should be approximately Clamp a temporary brace between the same two legs near where the feet will go. Doing so makes sure your legs will be vertical when we add this final support pieces and not tilted inward or outward.
6 Now that the legs are vertical, slide the small support pieces into their anticipated locations, with the 55 degree face down on the bench slats and the 35 degree face on the legs. Using a 7/32 drill bit, slide it through the seat attachment piece holes and twist it, marking the small support piece beyond with a small divot. Marking the drill point this way eliminates any wander from making a circle with an inserted pencil. Since you used a 7/32 drill bit to make the hole, it should fit right in and be nicely centered. Do this for all four legs. Remove the small support pieces and using each divot as a guide, drill through them with the 7/32 bit. Returning the small support pieces to the bench, you can run #10-32 bolts through both pieces and seat attachment pieces as shown below. Again, make sure you put washers on both the head and the nut of the bolt. Holding each support piece in place, drill in a # sheet metal screw.
7 You should have legs that look similar to the bench below. It s time to reinforce the leg joints. You should notice small gaps between the leg support pieces and the legs. In the picture above, it s right above the S on the leg. Fill in these and all other gaps using a very high-strength adhesive such as epoxy. You can buy lots of different types of epoxies from generic hardware stores. A general-purpose epoxy will do if it s an indoor bench. The biggest difference will be the cure time but very generally speaking, the longer the cure time, the stronger the bond. Optional step: You can choose to add additional reinforcement to the leg/leg-support-piece junction by incorporating a mending plate. Puck feet
8 Puck feet add a great final touch to the bench, so I recommend adding them; however, they are not for the faint of heart and you ll need a router or end mill to do it. Remove the puck material about 1/2 down on the inside part of the puck, since that will be where the longer portion of the stick inserts. Measure each leg s cross section dimensions (1-3/16 x 0.75 or so, depending) and undersize the hole in the puck by about 1/32 (this depends on the puck hardness). This will allow the stick to compression fit into the puck. If your hole is accidentally too large, you can epoxy the stick into the puck. Once you ve routed or milled out all four puck feet, push them on and you have your bench!
9 Planning a DIY project this summer? Head to your nearest TIMBER MART for everything you need.
How to build a hockey stick chair
How to build a hockey stick chair The hockey stick chair is a project that's guaranteed to turn heads. It doesn t involve many special tools, but does involve a couple more types of hardware than usual.
More informationELEVEN COLLABORATIVE. CONFERENCE TOPS Assembly Instructions
ELEVEN COLLABORATIVE Table of Contents SUPPORT BRACE ASSEMBLY.... 3 TABLE BASE FRAME ASSEMBLY.... 4 LEG ATTACHMENT.... 5 TOP JOINING PLATE ASSEMBLY... 6 TOP CLAMP/TOP SPACER INSTALLATION.... 7 TOP PLACEMENT
More informationIntroduction. Rocky Mountain Westy Swing Away Carrier Kit Installation Instructions
Rocky Mountain Westy Swing Away Carrier Kit Installation Instructions Introduction Thank you for purchasing the Rocky Mountain Westy Swing Away Carrier Kit. We pride ourselves in the products we develop
More informationINSTRUCTIONS FOR ASSEMBLING YOUR CLEARMOUNT MITER SAW SCALE
INSTRUCTIONS FOR ASSEMBLING YOUR CLEARMOUNT MITER SAW SCALE Pictures shown are our SW7 but these instructions apply to all of our scales. Special information for other models is noted. ** Read & Follow
More informationConstruction (Models A to C): The first part of my project will be the construction of the benches. Each bench will be constructed into two pieces
Construction (Models A to C): The first part of my project will be the construction of the benches. Each bench will be constructed into two pieces for easy transport, installation, and maintenance in the
More informationMyOutdoorPlans.com. By Julian King [2X4 GARDEN BENCH]
MyOutdoorPlans.com By Julian King [2X4 GARDEN BENCH] CUT LIST A 2 pieces of 2 4 lumber 24 long, 2 pieces 32 1/2 long LEGS B 2 pieces of 2 4 lumber 45 long, 2 pieces 15 1/2 long, 1 piece 12 1/2 long SEAT
More informationDesign Update /29/2006
Design Update 3 -- 8/29/2006 Since our first design we ve made many minor changes to key areas of the prayer bench, especially the folding hinge geometry. The general design remains the same, though the
More informationSheet Metal Brake Plans for a 6' Sheet Metal Brake
Sheet Metal Brake Plans for a 6' Sheet Metal Brake,1752'8&7,21 Thank you for purchasing the sheet metal brake plans. The plans include a complete list of material needed and easy to follow steps to build
More informationMiata Air Radical Splitter/Protector
Miata Air Radical Splitter/Protector Year: 2004-2005 MazdaSpeed Item: TDR-04M125 Thank you for purchasing the Track Dog Racing Radical. The Air Splitter is designed to help protect the factory MazdaSpeed
More informationDIY RUSTIC HALL TREE
DIY RUSTIC HALL TREE *Before beginning this project, please read through all of the plans as well as the blog post associated with this project. Always use safety precautions whenever using power tools
More informationOutdoor Swing and Arbor
America s leading woodworking authority Step by Step construction instruction. A complete bill of materials. Outdoor Swing and Arbor Exploded view and elevation drawings. How-to photos with instructive
More informationHinge Mortising Jig. One of the make it or break it parts of building a. 6 ShopNotes No. 74
Hinge Mortising Jig A Mortise for a Hinge. Quick, clean, and accurate that s the only way to describe the mortise you get with a trim router and this hinge mortising jig. One of the make it or break it
More informationBISON GOOSENECK FOOTBALL 1 PAIR OF GOAL POSTS
Instruction Manual BISON GOOSENECK FOOTBALL 1 PAIR OF GOAL POSTS Customer Service (800) 247-7668 P A R T S L I S T Item Qty Description Item Qty Description A 2 GOOSENECK POLE I 4 UPRIGHTS B 2 BAND CLAMP
More informationPickup Box Utility Rack Package Installation (Instruction ID: )
017 Chevrolet Colorado Pickup - WD (VIN S) Canyon, Colorado Accessory Installation Manual N America Document ID: 3966961 Pickup Box Utility Rack Package Installation (Instruction ID:3144879) Installation
More informationLOFT DOOR HANGER BARN DOORS & HARDWARE. Hardware Installation Instructions. Page
LOFT DOOR HANGER Page 1 Specifications 2 7/16" 3/8" 1-1/2 1-3/4 Ø3 3 7/8" 11-1/16 Page 2 Parts and Tools Tools Needed Tape Measure Pencil Drill with 1/8, 1/4 and 3/8 bits, 1 spade bit and Phillips bit
More informationLARGE PLYWOOD CUTTING GUIDE
Copyright 2015 Shanty-2-Chic.com Workbench I f you are tight on space but large on ideas this bench is just what you need. Sturdy and mobile this bench has an ingenious fold out wing that gives you over
More information(28) 2 x 4 x 8 Ft. Boards Tape Measure (9) 2 x 6 x 8 Ft. Boards Pencil (6) 2 x 2 x 8 Ft. Boards Carpenter s Square (9) 1 x 3 x 8 Ft.
MATERIALS: TOOLS: (28) 2 x 4 x 8 Ft. Boards Tape Measure (9) 2 x 6 x 8 Ft. Boards Pencil (6) 2 x 2 x 8 Ft. Boards Carpenter s Square (9) 1 x 3 x 8 Ft. Boards Drill 2 ½-inch Pocket Screws Circular Saw 2
More informationDewalt Organizer Storage Cabinet Plans
Dewalt Organizer Storage Cabinet Plans Version 1.0 How to build a system to perfectly organize you Dewalt storage organizers. With easy to follow step-by-step instructions, you will be able to cut, assemble,
More informationFor additional assistance call
The following pages will help guide you through the process of assembling your new 48 custom prize wheel. Choose an assembly area with plenty of room to lay your pieces on the floor and also a bench or
More informationCharlotte Dressing Table & Stool Set L4294
Thank you for shopping with GLTC, we hope you enjoy having this product in your home. We know assembling furniture, toys or accessories is not everyone s favourite way to spend their time, so we ve tried
More informationDIY ALIGNMENT GAGES. Next cut the aluminum to length. o Cut 2 pieces of the 1 in sq. tube: One pc 19 inches long One pc 12 inches long
DIY ALIGNMENT GAGES If you thrash your Corvette around the track like I do, then frequent alignments are the norm for you. Costs vary, but $130 or more is what you usually face. This DIY article will show
More informationSimple Woodworking: Outdoor Pitch Chair
Parts Lumber Front Front Leg Front Leg Drill three pocket holes on each end of the Front - one centered and two 3/4" from each side. Cut a 15-degree miter on one end of the Front Legs. It will be easier
More informationATLANTIS RAIL Contact Information
ATLANTIS RAIL Contact Information Customer Service (800) 541-6829 (508) 732-9191 Spectrum System Installation Instructions Atlantis Rail s Spectrum System is an easy to install, universal cable railing
More informationImportant Note: Why this guidebook is FREE?
Easy DIY Murphy Bed Construction Guide 1 Important Note: This guide is a FREE SAMPLE of our Complete Construction Guidebook. With the help of this guide you will get familiar with the construction steps
More informationChief s Shop: Simple Woodworking Bench
Chief s Shop: Simple Woodworking Bench Be sure to read the instructions and review the illustrations and accompanying video for this project BEFORE you start. Follow ALL SAFETY GUIDELINES AND RECOMMENDATIONS
More informationCONTINUED. TABLE TOPS: 1. Sort one 2x6x8 piece from your lumber. 2. Measure and mark two 48 pieces from each, then cut.
# Materials: Quantity Each: Total Quantity: x4x8 7 x6x8 1 TIPS FOR SUCCESSFUL PREP WORK: Before starting, carefully read through the entire instruction sheet. Refer to the material list to the left and
More informationCONTENTS TOOL LIST U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS. Revised: June 2013
U P S I D E I N N O V A T I O N S, L L C RAMP AND STEP SYSTEM ASSEMBLY INSTRUCTIONS TOOL LIST Required Tools: - Reciprocating Saw with Metal Cutting Blade - Drill - 7/16 Drill Bit for Metal Drilling -
More informationThank you for purchasing these easel plans. I think you will find this to be a fun, easy to build project that will serve you for years to come.
Construction Plans for The Basic Wooden Easel Updated August, 2002 Thank you for purchasing these easel plans. I think you will find this to be a fun, easy to build project that will serve you for years
More informationInstructions for Bed Assembly
Instructions for Bed Assembly 1. Platform Ends (2) 2. Mattress Slats (11-12) 3. Platform Center 4. Platform Sides (2) 5. Safety Rails (2-8) 6. Corner Supports (smaller than pictured) 7. Long Cross Bar
More informationwoodworkersjournal.com MATERIAL LIST
MATERIAL LIST T x W x L 1 Legs (2) 1 1 2" x 3 1 2" x 36 7 16" 2 End Uprights (2) 1 1 2" x 3 1 2" x 32 1 2" 3 Stringers (4) 1 1 2" x 3 1 2" x 42" 4 Top Cladding, Long (2) 3/4" x 7 1 4" x 65 3 4" 5 Side
More informationPlans. Easy-to-Build Full-size Deluxe Murphy Bed Plan. For more plans, tools and hardware visit rockler.com
Easy-to-Build Full-size Deluxe Murphy Bed Plan Build a full-size Deluxe Murphy Bed complete with decorative molding and matching side cabinets! Plans For more plans, tools and hardware visit rockler.com
More informationWagon Vise Retrofit Installation Instructions. American Craft Woodworks. Wagon Vise
Wagon Vise Retrofit Installation Instructions American Craft Woodworks Wagon Vise Wagon Vise Retrofit Installation Instructions 2 Retrofit Installation Instructions Before you get started, please read
More informationMiata Radical Air Splitter/Protector
Miata Radical Air Splitter/Protector Year: 1990-1997 with Factory R-Package Lip Item: TDR-90M125 Thank you for purchasing the Track Dog Racing Radical Air Splitter. The Air Splitter is designed to help
More informationSteel Framed Miter Saw Bench
Steel Framed Miter Saw Bench Version 1.1 How to build Steel Framed Miter Saw Bench With easy to follow step-by-step instructions, you will be able to cut, assemble, and finish your very own steel miter
More informationNest Storage Bed in Fabric Designed by Niels Bendtsen
General Assembly Instructions Assembly requires two people and 1 2 hours. Assemble bed as near as possible to final resting area. Identify all parts and hardware before beginning assembly. Retain packaging
More informationINSTRUCTION MANUAL ORDER NO. V3R MODEL V3R. Collinear Gain Vertical for MHz
ORDER NO. V3R MODEL V3R Collinear Gain Vertical for 216-225 MHz INSTRUCTION MANUAL General Description The new Hy-Gain V3R VHF antenna is a collinear 5/8-wave omnidirectional vertical antenna for the 216-225
More informationPFW Installation Guide Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d Installation, Installatie gids
Maximum Flat Panel Weight: 100 lb. / 45.35 kg. Included Components Wall Mount (Qty 1) Extension Bracket (Qty 1 Pair) Bracket (Qty 1 Pair) 5/16 Flat Washers (Qty 4) Universal Spacers (Qty 8) M5 Allen Driver
More informationThe following instructions will guide you through the installation of your new vinyl railing.
Installation Guide St. James Vinyl T-Rail Tools Required Protective eye glasses 3/8 x 3 Concrete Anchors/Fasteners (for Tape measure concrete installations) Variable speed drill/screwdriver Philips Driver
More informationFLOE DOCK FURNITURE WARNING ASSEMBLY INSTRUCTIONS
FLOE DOCK FURNITURE ASSEMBLY INSTRUCTIONS KIT P/N 510-00400-02 KIT P/N 510-00405-02 KIT P/N 510-00406-02 KIT P/N 510-00410-02 WARNING IT IS THE INSTALLER S RESPONSIBILITY TO PROPERLY INSTALL this chair
More informationPFW 6875 Installation Guide Installationsanleitung, Guía de Instalacíon, Guida de Installazione, Guide d Installation, Installatie gids
Maximum Flat Panel Weight: 160 lb. / 72.57 kg. Included Components Wall Mount (Qty 1) Extension Brackets (Qty 2) Bracket (Qty 1 Pair) 5/16 Flat Washers (Qty 4) Universal Spacers (Qty 8) M5 Allen Driver
More information7902 Dado Jig. Owners Manual Please Read Carefully! Hardware List: 7902 Parts List:
7902 Dado Jig Owners Manual Please Read Carefully! 7902 Dado Jig Hardware List: Identify and verify that you have all of the hardware shown below prior to assembly. Please read the instructions at least
More informationCHAPTER 8. Through Dovetail Procedures
CHAPTER Through Dovetail Procedures 52 Chapter D4 User Guide THROUGH DOVETAIL PROCEDURES Chapter Foreword In these instructions for using the Leigh Dovetail Jig, we have recommended using certain cutters
More informationPROJECT PLAN. 3-hour cedar bench
PROJECT PLAN 3-hour cedar bench This article originally appeared in The Family Handyman magazine. For subscription information, visit www.familyhandyman.com Please note that pages that appeared in the
More informationCoro Character PVC Frame Instructions:
Coro Character PVC Frame Instructions: In this tutorial we will show you how to make a basic light weight frame for your Coro character. Then we will show you how to add on to your frame to help you either
More informationWhy are we giving this guidebook as a FREE download?
Construction Guide Queen, Double & Twin Vertical 1 Note: This guide covers the construction steps for all 3 sizes of the vertical wall mount Easy DIY Murphy beds, Queen, Double and Twin. The construction
More informationParts list: Original Bear Chair BC Bear chair Nederland Postbus AM Zeist
INSTRUCTIONS KIT BEAR CHAIR BC201 Parts list: NR. parts Quanty Legs 2 Seat slats 6 Arm support 2 Triangles 2 5. Arms 2 Additional Arm Support 2 Struts 2 Sides, left (L) en right (R) 2 Bottom Back Support
More informationEquilibrium. Conference Table. Installation Instruction. Revision B 11/07/16
Equilibrium Conference Table Installation Instruction Revision B 11/07/16 Equilibrium End User Agreement Enwork Equilibrium table bases must be installed directly onto a four inch minimum thickness concrete
More informationParts List. U-DS92ST Ashley Creative Center With Padded Stool Assembly Instructions. [15] - Plastic Thick Washer (2 - pieces) [22] - Wrench (1 piece)
[1] - 23.5 x 35.5 Top [8] - Drawer Support Rods Parts List [15] - Plastic Thick Washer (2 - pieces) [22] - Wrench [2] - Upper Base left End (1 pieces) [9] - Media Supports (1 pieces) [16] - loor Guides
More informationPORTA~TRACE. GAGNE, INC. 41 Commercial Dr. Johnson City, New York Phone: Fax: ASSEMBLY INSTRUCTIONS
PORTA~TRACE GAGNE, INC. 41 Commercial Dr. Johnson City, New York 13790 Phone: 1-607-729-3366 Fax: 1-607-729-7644 ASSEMBLY INSTRUCTIONS PORTA~TRACE MODEL 2436T LIGHT TABLE PORTA~TRACE MODEL 3648T LIGHT
More informationWallbeds Northwest ENDURA CABINET PLANS AND INSTRUCTIONS
Thank you for purchasing your Wall Bed from Wallbeds Northwest. If you have purchased a complete "Endura DIY Kit," then much of the work is already done for you. Please skip to assembly instructions. Note
More informationOsprey Platform Assembly Guide. Menunkatuck Audubon Society. Rev 1.0
Osprey Platform Assembly Guide Menunkatuck Audubon Society Rev 1.0 1 Menunkatuck Audubon Society is a local chapter of National Audubon Society. We serve the shoreline towns of West Haven, New Haven, East
More informationThe following instructions will guide you through the installation of your new vinyl railing stair kit.
Installation Guide Vinyl Standard Stair Railing Tools Required Protective eye glasses Tape measure Variable speed drill/screwdriver Rotary hammer or hammer drill and masonry percussion bit recommended
More informationIt can be either a 2½ seater bench seat (2 adult and a kid), or a 5 seater picnic table.
Page 1 Folding picnic table in both bench-seat and picnic table mode Introduction Description A single bench seat that can be changed into a picnic table with ease. This 'Bench come Picnic Table' is ideal
More informationSMART ROUTING KIT. Sliding Arm. Perpendicular Stops* Control the movement along the Y-axis. Traveler Two slots for positioning on the Guide Rail
SMART ROUTING KIT The EZ SMART Smart Routing Kit (SRK) is the original routing kit for the EZ SMART system. It turns the average router into a production tool capable of multiple axis routing with CNC-like
More informationMedium HoneyBadger Chase Rack Installation Instructions
PREPARATION Medium HoneyBadger Chase Rack Installation Instructions 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake. 2. We recommend reading
More informationPVC Swift/Skeiner Tutorial
PVC Swift/Skeiner Tutorial Windmill Arm Base The swift/skeiner is assembled in 3 pieces: the base, the arm, and the windmill. The three pieces can be taken apart so that the swift/skeiner can be stored
More informationPRODUCT: LOKI INSTALLATION INSTRUCTIONS. Product is covered by U.S. patents. For more information visit
R INSTALLATION INSTRUCTIONS PRODUCT: LOKI CONFIGURATION: SINGLE DOOR MOUNT: GLASS MOUNT Product is covered by U.S. patents. For more information visit www.krownlab.com . TOOLS + MATERIALS REQUIRED TOOLS
More informationBuilding Instructions
Building Instructions Tools Required Tape measure Straight edge Pencil/pen Jigsaw Table Saw Circular Saw Electric drill 1 Hole saw bit Saw horses/table Protractor Staple gun Caulk gun Paint brush Wrenches
More informationTOOL LIST FOR TAILGATE HIDDEN LATCH & LINK ASSY FOR FORD FLARESIDE TRUCKS
TOOL LIST FOR TAILGATE HIDDEN LATCH & LINK ASSY FOR 53-87 FORD FLARESIDE TRUCKS Vise Grip Clamps C-clamps Sharpie Marker Ball Peen Hammer Center Punch 3/8 or 1/2 Drill 5/32, 7/32, 9/32, and 3/8 Drill Bits
More informationKai Installation Instructions
Kai Installation Instructions Before Beginning Installation Read through the entire instruction thoroughly A minimum of 2 people are required for this assembly These instructions reflect typical assemblies;
More informationBMW R1100/R1150GS Instructions for Mounting Medium or Large Pack Rack and Micatech Top Case with Mount Kit
BMW R1100/R1150GS Instructions for Mounting Medium or Large Pack Rack and Micatech Top Case with Mount Kit Thank you for purchasing the Micatech Pack Rack and Top Case, with R1100/1150GS mount kit. Please
More informationFORD INTERCEPTOR SEDAN READY BUCKLE
INSTALLATION MANUAL FORD INTERCEPTOR SEDAN READY BUCKLE PART# FT3501RB We recommend you read through the installation guide prior to installation, if you have any questions please call us at 800-516-2322
More informationTail Vise. Installation Instructions. (revised 10/11/2017)
Tail Vise Installation Instructions (revised 10/11/2017) Lie-Nielsen Tail Vise Instructions Table of Contents page About Your Tail Vise 3 Parts List 4 step 1. Prepare Your Bench Top 5 step 2. Prepare the
More informationROCKWELL. Two Panel Door. Half X Door. Double X Door. Z Combination Door
ROCKWELL 4 in 1 DOOR Choose between four door styles with this Door Kit. Our versatile Rockwell Door Kit is very easy to assemble. All materials and hardware needed to assemble any of the four styles are
More informationInstallation Instructions for. Handrail Component System
Handrail STEP-BY-STEP Installation Instructions for Handrail Component System Rise in Inches Run in Inches 8 8.5 9 9.5 10 10.5 11 11.5 12 12.5 13 13.5 14 14.5 15 8.5 47 45 43 42 40 39 38 36 35 34 33 32
More informationWork Space Set-up. Slats will level the pipe during bending and help minimize twisting of the bow.
Work Space Set-up Affix pipe bender to end of working surface Slats will level the pipe during bending and help minimize twisting of the bow. Make the slat height equal the distance from your work surface
More informationROCKWELL 4-IN-1 DOOR. Two Panel Door. Half X Door. Z Combination Door. Double X Door
ROCKWE 4-IN-1 DOOR Two Panel Door Half X Door Double X Door Z Combination Door Choose between four door styles with this Door Kit. Our versatile Rockwell Door Kit is very easy to assemble. All materials
More informationMODEL T28173/T28174 ROLLER TABLES INSTRUCTIONS
MODEL T28173/T28174 ROLLER TABLES INSTRUCTIONS FOR MODELS MFD. SINCE 10/17 For questions or help with this product contact Tech Support at (570) 546-9663 or techsupport@grizzly.com Rails Rollers Reversible
More informationINSTALLATION MANUAL IOWA MOLD TOOLING CO., INC. BOX 189, GARNER, IA MANUAL PART NUMBER:
PARTS-1 Model 24562/28562 Crane INSTALLATION MANUAL IOWA MOLD TOOLING CO., INC. BOX 189, GARNER, IA 50438-0189 641-923-3711 MANUAL PART NUMBER: 99903701 Iowa Mold Tooling Co., Inc. is an Oshkosh Truck
More informationCMT Enlock Jig Owner s Manual
Thank you for purchasing the CMT Enlock Jig. This jig will simplify joinery in your shop, and on the job site. Please read the instructions thoroughly before using the Enlock Jig. Router requirements A
More informationReplacement Parts List: Left Side Components (as if you were sitting on the bike) QTY Price each Part Numbers Descriptions
Honda CBR600RR (09-12) Frame Slider Installation Instructions Part Numbers: 750-3349, 750-3340, 755-3349 & 850-3340 MADE IN THE USA! Carefully read instructions in their entirety before the install Professional
More informationSlide the stock rubber tank mount caps onto the ends of the CS-1 tank mount:
RYCA CS-1 BODY PARTS INSTALLATION GUIDE [The CS-1 installation guides should be used as supplements to the videos found on our Youtube Channel. There is no strict order to the build process, but it is
More informationPivot-Door Downdraft Cabinet Plans
Pivot-Door Downdraft Cabinet Plans Finished Cabinet Closed Open Exploded View Introduction This simple downdraft-style dust collection cabinet is a great way to keep your shop cleaner and keep your router
More informationCV1B Sliding Table Installation and Setup Guide
CV1B Sliding Table Installation and Setup Guide Tech Mark, Inc 7901 Industry Drive North Little Rock, AR 72117 tel (501) 945-9393 fax (501) 945-0312 www.tech-mark.com email: info@tech-mark.com The CV1B
More informationRange height adjustable assembly
Table of contents Digital handset operation 3 Height adjustable bench kit 4-5 Cable carrier 6 Ganging tray and ganging rail 7 Height adjustable return frame kit 8 Cable entry pole 9 24 and 30 d worksurfaces
More informationSTANDARD CANOPY WORK REPORT B-1
STANDARD CANOPY WORK REPORT B-1 No. Check Parts / Tools Qty _ Canopy Lock 1 [ ] 6E2-3 Canopy Hinge Block 1 2 [ ] 6E4-5 Canopy Side Frame 2 2 [ ] 6E2-1 Canopy Lock Assembly 1L + 1R 3 [ ] 6E2-4 Rear Lock
More informationBuild a Stout Workbench
Build a Stout Workbench Tail vise is at the heart of this versatile bench by chris gochnour I ve done a fair amount of handplaning during my 32 years as a professional furniture maker, and I ve found that
More informationTimber projects. This section contains plans and instructions for three timber projects.
Project Saw horse Timber projects This section contains plans and instructions for three timber projects. The projects are suggested for students to practise skills use tools from the course and make something
More informationOPERATOR'S MANUAL RULES FOR SAFE OPERATION
OPERATOR'S MANUAL #4950300 ROUTER AND JIG SAW MOUNTING KIT (FOR USE WITH THE BT3000 TABLE SAW) CONGRATULATIONS AND THANK YOU FOR BUYING THIS RYOBI ROUTER AND JIG SAW MOUNTING KIT. Your new #4950300 Router
More informationMedium Pro Table Top Stand
Medium Pro Table Top Stand Build Manual Thank you for purchasing a Foam-Flite model airplane stand. Your Foam-Flite stand was designed by modelers just like you looking for an economical and versatile
More information10x10 Trellis Pergola
0x0 Trellis Pergola ASSEMBLY GUIDE Ver.-007 Table of Contents PAGE 0x0 Trellis Pergola Introduction & Overview...................................................... Pergola Materials Overview..............................................................
More informationLocker Pedestal Installation Instructions
Locker Pedestal Installation Instructions LK-PED-INST-0314r1 Parts List Single Pedestal Back to Back Pedestal Horizontal Support Tube TS-169 Post Flange TS-190 Post Cap Fasteners Provided: #8 x ¾ round
More informationF i t t i n g t h e N e w L a n d i n g G e a r t o Y o u r S k y J i b V 1
F i t t i n g t h e N e w L a n d i n g G e a r t o Y o u r S k y J i b V 1 1 P a r t s L i s t : S t a n d a r d L a n d i n g G e a r U p g r a d e Product Code Parts + Spares Product Code Parts + Spares
More information10 x 10 Flat Top Two Tone Pergola
0 x 0 Flat Top Two Tone Pergola Models: Bordeaux ASSEMBLY GUIDE OPTIONAL ACCESSORIES Arch Kit System ( Arches) Privacy Fence Panel System ( Panels & Middle Post) Bolt Down Bracket Kit ( for Pergola) Ver.0-00
More informationButterfly Leaf Dining Table Plans
Butterfly Leaf Dining Table Plans Part 1 An attractive dining table with a secret: the leaf folds and stores inside the table. Season 1, Episode 7 P a g e 2 I first saw a butterfly leaf table in a back
More informationRockwell 4-in-1 Sliding Door
Rockwell 4-in-1 Sliding Door ASSEMBLY INSTRUCTIONS ROCKWELL 4-IN-1 SLIDING DOOR Recommended Tools Drill with Phillips Bit Socket Wrench with 7/16 Socket Rubber Mallet Adjustable Square ROCKWELL 4-IN-1
More informationIF INSTALLING ANY OF THE PORTMAN SELF CLOSING SYSTEMS, PLEASE READ THE CORRESPONDING FITTING INSTRUCTIONS SUPPLIED WITH THE CLOSING SYSTEM FIRST
Set A Set B PFD60 Fire Door Kit FITTING INSTRUCTIONS IF INSTALLING ANY OF THE PORTMAN SELF CLOSING SYSTEMS, PLEASE READ THE CORRESPONDING FITTING INSTRUCTIONS SUPPLIED WITH THE CLOSING SYSTEM FIRST SUGGESTED
More informationInstallation Instructions for Vista Air Vertically Folding Walls
Installation Instructions for Vista Air Vertically Folding Walls Use these instructions in conjunction with your shop drawings to see the specifics that are particular to the model you are installing.
More informationMODEL T " X 72" BEECH CABINETMAKER'S WORKBENCH INSTRUCTIONS
MODEL T1251 25" X 72" BEECH CABINETMAKER'S WORKBENCH INSTRUCTIONS For questions or help with this product contact Tech at (570) 546-663 or techsupport@grizzly.com Introduction This cabinetmaker's workbench
More information16. Wing Final Assembly and Installation
Section Objective: Installation and rigging of ailerons. Pitot tube install, and any other wing related items. Required Parts: Left aileron push rod ALA-0072, Right aileron push rod ALA-0073, Push tube
More information10x10 Trellis Pergola
0x0 Trellis Pergola ASSEMBLY GUIDE Ver.0-7 Table of Contents PAGE Introduction & Overview...................................................... Pergola Materials Overview..............................................................
More informationSLIDING MECHANISM TROLLEY CATCH TROLLEY ASSEMBLY FLOOR GUIDE
Set A Set B P7001 Standard Kit Glass Door FITTING INSTRUCTIONS SUGGESTED TOOLS DRILL MITRE/CHOP SAW TAPE MEASURE (Image for reference only) HACKSAW POCKER DOOR KIT SHORT / LONG Z SECTION LONG Z SECTION
More informationParts & Tools. O'Cello printing and assembly instructions. o-cello.com
The O'Cello is a 3D-printable cello developed by Conor O'Kane, which is free to download and print for personal use. This document will show you how to print and assemble your own O'Cello. For the latest
More informationRipple Hanger ASSEMBLY INSTRUCTIONS
Ripple Hanger ASSEMBLY INSTRUCTIONS RIPPLE HANGER Recommended Tools Drill with 1/8, 1/4, and 1/2 Drill Bits, 1-1/8 Forstner Bit or 1-1/8 Spade Bit, and Phillips Bit 9/16 and 5/8 Combination Wrench Socket
More informationHeavy-Duty Bypass Track System
Heavy-Duty Bypass Track System Please Note: This track system must be installed with the screws going into a solid surface such as studs or a header. Due to the spacing of the holes on these Brackets,
More informationBulkhead Model Number and
Bulkhead Model Number 96141-3-01 and 96142-3-01 Installing your ProMaster bulkhead is very clear cut following these instructions. Before cutting or drilling in the floor, verify the location of you gas
More informationSTYLE BAR & TONNEAU COVER INSTALLATION
STYLE BAR & TONNEAU COVER INSTALLATION INSTALLATION MANUAL: 2005 to '09 Mustang P/N: 10-8002-C12071B Saleen Performance, Inc. 1225 East Maple Rd., MI 48083 800-888-8945 www.saleen.com 1 IF YOU ARE NOT
More informationInstalling the Profile Privacy Panel. Assemble top mounting bracket. Prerequisites. Tools
Installing the Profile Privacy Panel Complete these instructions to install the Profile Privacy Panel. Privacy panels are available in various heights to match tiers and include mounting hardware for slat
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Universal Low Profile Tilt Mount Model: U.S. Toll Free: 1-866-752-6271 Outside N. America: 1-503-748-5799 E-mail: ts@planar.com FRANCE Phone: +33 5 6378 3810 E-mail: emeats@planar.com
More informationReady To Go SimpleSpec tm. Installation Manual. For more information, please visit 3-form.com or call
Contents Overview ( 1) 3/8" Varia Panel = Cable Tensioner with Cover Plate KIT Stainless Steel: 3-15-1636-K Black Oxide: 3-15-2005-K Cable Tensioner with Cover Plate SS: 3-15-1636 BO: 3-15-2005 + M8 Thread
More information