Pathways Privacy Wall Glass Selections - Sliding Door
|
|
- Franklin Young
- 5 years ago
- Views:
Transcription
1 Pathways Privacy Wall Glass Selections - Sliding Door #2 ACR BIT 3/16" HEX BIT RAYBO ETCHED GLASS STYLES: Satin Mist PATTERN GLASS STYLES: Waterfall Bamboo Harp Mirage If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE ( ) for immediate action by people who want to help you. (Outside the U.S.A., Canada, Mexico, Puerto Rico, and the U.S. Virgin Islands, call: ) Or visit our website: Steelcase Inc. Grand Rapids, MI U.S.A. Printed in U.S.A. NOTE: For etched/pattern glass orientation please refer to the installation drawings. Unless noted otherwise, use the default. DEFAULT GLASS ORIENTATION: ETCHED GLASS: Rough side to go on the inside of the office space. PATTERN GLASS: Rough side to go on the outside of the office space. 1/16" ALLEN WRENCH LOCTITE 425 Page 1 of 15
2 ENGAGEMENT CLIPS SLIDER STRIKE PLINTH TRIM SLIDER SIDELITE PLINTH TRIM SIDELITE CORNER PLINTH TRIM Glass Selections Components SLIDER DOOR TWO VERSIONS: OLD VERSION USED PRIOR TO JAN NEW VERSION USED AFTER DEC (OLD VERSION SHOWN) SLIDER DOOR SIDELITE PANEL SLIDER DOOR FRAME DOOR SEAL SLIDER DOOR TRACK CHANNEL CAP ASSEMBLY SLIDER STOP BUMPER POWER (OPTIONAL) LOW VOLTAGE COMPONENTS WATT STOPPER LOW VOLTAGE WIRE HANDLE PACKAGE USED PRIOR TO JAN 2006 (LOCKING VERSION) HANDLE PACKAGE USED AFTER DEC 2005 (LOCKING VERSION) HANDLE PACKAGE (NON-LOCKING VERSION) DOOR BASE COVERS CEILING RETENTION BRACKET LOW VOLTAGE SWITCH QUICK CONNECTS Page 2 of 15
3 = Inline Feature Strip = Half Feature Strip Connection Conditions NOTE: All other connection conditions are the same as standard panel mounting connection conditions " ~ (1-11/32") C L C L Sliding Door 90º with Centered Sliding Door 1.341" ~ (1-11/32") C L C L Sliding Door Sliding Door "T" with Sliding Doors Centered Page 3 of 15
4 NOTE: Ceiling retention bracket is to be placed as close to slider door frame as possible. Bend bracket so each leg is parallel and install into top horizontal. Place flat-bladed screwdriver through the clearance holes and twist to secure into top horizontal. 1 FLAT-BLADED SCREWDRIVER CEILING RETENTION BRACKET TOP HORIZONTAL 1. Install the slider door sidelite panel. Place top of panel into ceiling track first and then swing base of panel toward the floor. SLIDER DOOR SIDELITE PANEL 2. Engage the post extension by inserting a screwdriver into the slots and slowly tapping the extension upward (2a) by engaging the small holes in the extension (2b). Extend fully to top of ceiling channel. 2b 2a NOTE: Level frame before installing feature strips. POST EXTENSION NOTE: Adjoining frame removed from illustration for clarity. Page 4 of 15
5 SLIDER DOOR FRAME 3. Install the slider door frame next to the slider door sidelite panel. 4b Place top of slider door frame into ceiling track first and then swing base of frame toward the floor. 4. Engage the post extension by inserting a screwdriver into the slots and slowly tapping the extension upward (4a) by engaging the small holes in the extension (4b). Extend fully to top of ceiling channel. 3 4a POST EXTENSION NOTE: Adjoining frame removed from illustration for clarity. NOTE: Level frame before installing feature strips. Page 5 of 15
6 5. Note portion of cap that needs to be removed (5a) and cut with hand saw (5b). 6. Remove paper from double face tape and install cap assembly as indicated. 7. Install slider door track channel into grooves located on the frame (7a). Tighten set screw to secure (7b). SLIDER DOOR TRACK CHANNEL 7a THIS PORTION OF THE CAP TO BE SCRAP 7a 7b 5a 13 / b CAP ASSEMBLY Page 6 of 15
7 9 8. Tighten the set screw with an Allen wrench on each wheel assembly. Loctite 425 will be added for a firmer holding set screw shown in step 13 on page Loosen the screw that holds each engagement clip, so that the screw is only started into the engagement clip. 9 ENGAGEMENT CLIP ENGAGEMENT CLIP TOP OF SLIDING DOOR 8 8 Page 7 of 15
8 SLIDING DOOR TRACK WHEEL 10b Side View SLIDING DOOR FRAME 10. Place top of sliding door onto sliding door track (10a) making sure the door is at an angle and the wheels align properly into track (10b). 10a While lowering, make sure the base of the slider door fits properly over the two (2) pins located at the base of the slider door sidelite panel (10c). Keep the gap between the top of the door and the cap at a minimal clearance to help keep the wheel engaged into the track (10d). MINIMAL CLEARANCE 10d SLIDING DOOR SLIDING DOOR TRACK 10c WHEEL ENGAGED IN TRACK SLIDING DOOR PINS SLIDER DOOR SIDELITE PANEL Page 8 of 15
9 11. Apply one (1) drop of Loctite 425 under the head of each #6 screw for strength and tighten. 12. Test to see if sliding door anti-dislodgement clips have been installed properly by lifting on each side of the sliding door making sure the door doesn't come off the sliding door track. Slide door its full range to test for any binding. 13. Back out the set screw two or three turns and apply one (1) drop of Loctite 425 to the threads then re-install the set screw to its original position View Shown Without Wall For Clarity 11 View Shown Without Wall For Clarity 13 View Shown Without Wall For Clarity View Shown Without Wall For Clarity Page 9 of 15
10 14. Using a phillips head screwdriver, loosen screws on base plate (14a) and lower base plate to within a 1/4" from the floor (14b). Then tighten screws. 15. Remove paper from velcro pad and install onto door base cover as indicated (15a). Install door base covers over the base plate as shown (15b). Install door bottom end trims on each end with one (1) flat head screw to lock base covers onto door (15c). 14a VELCRO PAD 1/4" FLOOR 14b 15a DOOR BOTTOM END TRIMS 15c 15b DOOR BASE COVERS Page 10 of 15
11 This page describes the handle package that is used after Dec Adjust the height of the lock barrel by turning the lock barrel a minimum of 1/16" from surface of handle plate. 17 1/16" MIN 16. Install door handle (16a). Secure using two (2) screws (16b). Non-Locking Version Locking Version 18b 16a 18. Peal off paper on back of door seal and apply door seal to frame as shown (18a). Start at top and work downward (18b). PAPER SEAL 16b 18a SCREW SCREW Page 11 of 15
12 This page describes the handle package that was used prior to Jan Adjust lock latch by turning the adjustment screw. 16. Install door handle (16a). Secure using two (2) screws (16b). Non-Locking Version Locking Version 17 18b 16a 18. Peal off paper on back of door seal and apply door seal to frame as shown (18a). Start at top and work downward (18b). PAPER SEAL 16b 18a SCREW SCREW Page 12 of 15
13 19a NOTE: Clean attachment area with alcohol (or naptha) before applying plinths. 19. Remove paper from double face tape and attach slider strike plinth trim as shown (19a). Remove paper from double face tape and attach slider sidelite plinth trim as shown (19b). Remove paper from double face tape and attach sidelite corner plinth trim as shown (19c). NOTE: When attaching a slider within a centerline 'L' or 'T' application, installer may have to machine leg of plinth off. View Shown Without Door For Clarity SLIDER STRIKE PLINTH TRIM 19b SLIDER SIDELITE PLINTH TRIM Remove this area of plinth. 19c SIDELITE CORNER PLINTH TRIM Page 13 of 15
14 WARNING: All electrical installations should be done by a qualified electrician in accordance with codes and regulations applicable at the installation site. 120V or 277V white black transformer red red l i g h t r e d b la c k b l u e Low Voltage Switch - Standard Inside Frame Application 1. Attach watt stopper to J-box (1a). Route low voltage wire up through bottom of floor or down from ceiling in full height scenerios only (1b). 24VCD switch 1b 2. Pull low voltage wire through opening and attach to quick connects (2a). Attach low voltage switch to quick connects (2b) and insert assembly into hole (2c) and snap into place. LOW VOLTAGE WIRE 2c 1a J-BOX WATT STOPPER LOW VOLTAGE WIRES 2a QUICK CONNECTS 2b LOW VOLTAGE SWITCH Page 14 of 15
15 WARNING: All electrical installations should be done by a qualified electrician in accordance with codes and regulations applicable at the installation site. 3/8" Low Voltage Switch - Feature Strip Application (For all locations except inside corners) 3 1. Attach watt stopper to J-box (1a). Route low voltage wire up through bottom of floor or down from ceiling in full height scenerios only (1b). See page 14 for schematic and artwork. 2. Remove a 1-1/2" portion of aluminum from the two mating panel uprights where the feature strip is mounted. 3. Measure 44" for the length of the bottom feature strip and place a 3/8" notch on one end of the feature strip as shown. 4. Snap bottom feature strip into postion /2" 5. Pull low voltage wire through opening and attach to quick connects (5a). Attach low voltage switch to quick connects (5b) and insert assembly into hole (5c) and snap into place. 6. For the top feature strip, 5c make the same 3/8" notch on one end of the feature strip (as shown on step 3) and slide the notched end under the low voltage switch and snap into position. 5a LOW VOLTAGE WIRES 44" " 43-3/4" 5b LOW VOLTAGE SWITCH QUICK CONNECTS TOP & BOTTOM FEATURE STRIPS LOW VOLTAGE SWITCH Page 15 of 15
Privacy Wall Glass Selections - Polished Edge Slider Door
Privacy Wall Glass Selections - Polished Edge Slider Door 3/6" HEX BIT PUTTY KNIFE #2 ACR BIT SUCTION CUP HOLDERS DOOR LEAF: Satin Tempered Clear Tempered LOCTITE 425 SIDE LIGHT ETCHED GLASS STYLES: Satin
More informationPrivacy Wall & Glass Selections Pivot-Hinged Door (For products manufactured after September 14, 2009)
Privacy Wall & Glass Selections Pivot-Hinged Door (For products manufactured after September 14, 2009) 3/16" HEX BIT #2 ACR BIT 3/8" HEX SOCKET Full-Height (No Switch) Transom (No Switch) Full-Height (With
More informationSeries 9000 Panel Door; In-Line, Corner and Permanent Wall Application
Series 9000 Panel Door; In-Line, Corner and Permanent Wall Application 5/32" Drill Bit In-Line Corner Permanent Wall 3/16" Allen Wrench If you have a problem, question, or request, call your local dealer,
More informationHeight Adjustable Benching End Panel and Utility Pole
Height Adjustable Benching End Panel and Utility Pole Tools required: END PANEL Jig Saw Power Drill END PANEL WITH UTILITY POLE Bit Holder Long #2 Square Drive Bit 5mm Hex Drive Bit UTILITY POLE Level
More informationFlexFrame - Storage Components and Skins
FlexFrame - Storage Components and Skins 1/4 Square Drive Ball-Point Hex-Bit Socket 1/8 Short Hex, 1-1/2 Overall Length McMaster Part # 54075A44 Table of Contents Topic Page Storage Components 2 General
More information434 Cobi Chair - Seat Shell Replacement
434 Cobi Chair - Seat Shell Replacement PROFILE OF HARDWARE FOR CLARITY #8-18 x 1/2" Pan Head Tapping Screw Magnetic Bit Holder M6 x 45mm Wafer Head Screw T-30 Large flat-bladed screwdriver If you have
More informationOpus Standard Corner Trim Unit
Opus Standard Corner Trim Unit If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522) for immediate action by people who want to help you.
More informationAnswer Power Beam and Boundary Screen
Answer Power Beam and Boundary Screen 5/16 MAGNETIC 3/8 If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522) for immediate action by
More informationOpus Base Unit Assembly
Opus Base Unit Assembly 5/16" NOTE: All cam locks need to be rechecked to confirm they are tight before installation. Gaps could result if not completely tightened and effect assembly. 2 Foot Scrap Board
More information487 Cachet Swivel - Base Chair Replace Front Seat Support or Seat
487 Cachet Swivel - Base Chair Replace Front Seat Support or Seat SPECIAL ALLEN WRENCH PROVIDED If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE
More informationJenny Legs Assembly Instructions
Jenny Legs Assembly Instructions R EXTENDED PHILLIPS BIT MM ALLEN WRENCH 6MM HEX DRIVE /" 007 Steelcase Inc. Grand Rapids, MI 90 U.S.A. Printed in U.S.A. Page of 6 88000 Rev F Jenny Club Instructions:
More informationAtrium Patio Door Field Service Manual
Atrium Patio Door Field Service Manual December 2005 Table of contents Service Agreement Pg 2 Release Agreement Pg 5 Inspection form Pg 6 Warranty Pg 8 Replacing swing panel Pg 12 Replacing sliding panel
More informationPremium Whiteboard and Tackboard Mounting
Premium Whiteboard and Tackboard Mounting #2 BIT If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522) for immediate action by people
More informationc:scape Shared Tables - Freestanding and Tethered
c:scape Shared Tables - Freestanding and Tethered Furniture should be installed in sequence shown below. 1 2 3 4 5 6 BEAM MID STORAGE DESKING POWER LOW STORAGE PRIVACY THIS INSTALLATION SEQUENCE IS HERE.
More information110 and 555 Markerboard, Chalkboard and Tackboard Mounting
0 and 555, Chalkboard and Tackboard Mounting 0 # BIT 0 Splined 0 and 555 Tackboard POWER GRIPS 555 If you have a problem, question, or request, call your local dealer, or Steelcase Line at 888.STEELCASE
More informationAssembly Instructions
Unite Panel System Hinge Door July 2016 #12 x / slotted hex washer head bolt Figure 1 threshold bracket frame Detail F threshold bracket threshold bracket (installed) #12 x / slotted hex washer head bolt
More informationmedia:scape HDVC Wall Mount
Dual Shroud media:scape HDVC Wall Mount Single Shroud CAUTION Quad Shroud FAILURE TO FOLLOW THESE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. Triple Shroud Read the entire Assembly
More informationLow Headroom Rear Mount TorqueMaster
Low Headroom Rear Mount Supplemental Instruction Insert This supplemental installation instruction is to be used as a supplement to the main Installation Instruction and Owner s Manual provided with the
More informationLarge Case Storage - Counterweights
Large Case Storage - Counterweights Lateral File/Combo Cabinet CAUTION Please refer to the Steelcase Specification Guide for Storage for additional guidance on determining the correct counterweight package.
More informationINOVO 4-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS
INOVO 4-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS IMPORTANT: READ THE INSTRUCTIONS AND FAMILIARIZE YOURSELF WITH THE DOOR PARTS AND PIECES BEFORE BEGINNING ASSEMBLY AND INSTALLATION.
More informationIMPULSE G2/PULSE STATIC BRIDGE & RETURN MODULE. Drill. Desk Connecting. Outside by fastening the supplied wood screws from the HK-67 kit through the
PART # 1608990 STATIC BRIDGE & RETURN MODULE 1. This sheet covers the steps to install a static bridge or return module with the FX no hinged access panel back option to a height adjustable freestanding
More informationcompile system INSTALLATION GUIDE Updated January 2019
INSTALLATION GUIDE Updated January 09 compile system Table of Contents Panels 0 Quick Connect Clips 0 Lock Clips 0 Panel Trims 0 Privacy Glass 0 Post Base Covers 04 Electrical 04 Power Distribution Harness
More informationSeries 7 AdjusTable Height Tables
Series 7 AdjusTable Height Tables Tools required: #2 Phillips Bit with Extension #2 Square Drive Bit 4mm Hex Drive Bit #3 Phillips Bit If you have a problem, question, or request, call your local dealer,
More informationFor additional assistance call
The following pages will help guide you through the process of assembling your new 48 custom prize wheel. Choose an assembly area with plenty of room to lay your pieces on the floor and also a bench or
More informationHow to Install Custom Real Wood and Faux Wood Blinds
Before you begin your installation: READ ALL INSTALLATION INSTRUCTIONS! Make sure that you have all tools and hardware needed for installation. Check the installation surface (wall, ceiling, or window
More informationModular & Hardwired Hub Assembly to "X" and "Y" Posts
Modular & Hardwired Hub Assembly to "X" and "Y" Posts Hardware Package T-Nut Data jack bracket #6 x 1/4" plastite trilobular screw 1/4-20 x 3/4" socket head cap screw #6-32 x 1/4" pan head screw #10-32
More informationINSTALLATION AND CARE INSTRUCTIONS
INSTALLATION AND CARE INSTRUCTIONS Vertical Applications Honeycomb Shades 52 C8-10-3401 Rev 2/14 CONTENTS Introduction...2 Before You Begin...3 Vertical Application Parts Overview...4 Materials Required...5
More informationIMPULSE G2/PULSE STATIC BRIDGE & RETURN MODULE. Drill. Desk Connecting. Outside by fastening the supplied wood screws from the HK-67 kit through the
PART # 1608990 STATIC BRIDGE & RETURN MODULE 1. This sheet covers the steps to install a static bridge or return module with the FX no hinged access panel back option to a height adjustable freestanding
More informationSLIDING TUB / SHOWER ENCLOSURE WITH STATIONARY 90º PANEL
SLIDING TUB / SHOWER ENCLOSURE WITH STATIONARY 0º PANEL This instruction sheet applies to the following units. C, C7, C7, C77, C, C7 This instruction sheet also applies to the following units. VTE / VSE
More informationIMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE
IMPORTANT: PLEASE RETAIN THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE 005-07 Cadillac STS Classic 3D Z, Classic Dual Weave, Classic Mesh & Classic Black Mesh Grilles B 7 HR 3 STS Classic 3D Z Grille Part
More informationPOWER PET. Low-E Automatic Patio Pet Door Installation and Operating Instructions
POWER PET Low-E Automatic Patio Pet Door Installation and Operating Instructions Power Pet, Regular Height, Patio Door Assembly Steps Estimated assembly time: Under 1 hour STEP 1: Assemble the tools you
More informationGared Pro-S Portable Backstop
Models: 9616 & 9618 Installation, Operation and Maintenance Instructions Please read all instructions before attempting installation or operation of these units SAVE THESE INSTRUCTIONS FOR FUTURE USE PUBLICATION
More informationINOVO 2-LITE SLIDING PATIO DOOR
INOVO 2-LITE SLIDING PATIO DOOR ASSEMBLY AND INSTALLATION INSTRUCTIONS IMPORTANT: READ THE INSTRUCTIONS AND FAMILIARIZE YOURSELF WITH THE DOOR PARTS AND PIECES BEFORE BEGINNING ASSEMBLY AND INSTALLATION.
More informationSeries Adjustable Height Tables
Series 7.2 - Adjustable Height Tables Tools required: Power Drill #2 SQUARE DRIVE BIT If you have a problem, question, or request, call your local dealer, or Steelcase Line 1 at 888.STEELCASE (888.783.3522)
More informationa.k.a. casegoods instructions
a.k.a. casegoods instructions a a.k.a. workwall installation IMPORTANT NOTES Failure to install product according to installation instruction will result in loss of warranty. Tools required for assembly
More informationWPS crew Doors Installation instructions
WPS-132-133 crew Doors Installation instructions ORDER OF INSTALLATION FOR A COMPLETE ENCLOSURE OF A CREW WPS (Weather Protection System) IS AS FOLLOWS: 1. Heater 2. Rear Thresholds - Right Hand & Left
More informationInstallation And Care Instructions. Vertical Honeycomb Shades
Installation And Care Instructions Vertical Honeycomb Shades Rev 5/2013 Table Of Contents Getting Started... 3 Parts Overview... 4 Materials Required... 5 Tools Required... 6 Outside Mount Installation...
More information488 Brody Disassembly Direction
488 Brody Disassembly Direction Lighting (see page 8) Screens (see page ) Backrest (see page 4) " and " BIT HOLDERS Side Surface (see page ) T0, T0, T40 TORX Personal worksurface (see page 6) Caddy (see
More informationTOOLS REQUIRED Metal Wood Wood and Metal Screws. #16 Drill #12-24 Tap. 1/8 Drill
DEVICES COVERED IN THIS DOCUMENT: 4700S Surface Vertical Rod Device 4700SF Fire Exit Surface Vertical Rod Device TOOLS REQUIRED Metal Wood Wood and Metal Screws Sex Bolts #7 Drill ¼ -20 Tap #16 Drill #12-24
More informationSeries 4 HV Single Monitor Lift Assembly Instructions
6703 Zinser Street Schofield, WI 54476 6/13/17 Series 4 HV Single Monitor Lift Assembly Instructions Read all the instructions before beginning. Hardware Pack # 53368 Page1 OF 6 Tools Required for Assembly:
More informationCONCEALED VERTICAL ROD PANIC EXIT DEVICE
INSTALLATION INSTRUCTIONS CRL JACKSON 1085-1085P CONCEALED VERTICAL ROD PANIC EXIT DEVICE crlaurence.com Phone: (800) 421-6144 Fax: (866) 921-0531 crlaurence.com usalum.com crl-arch.com 11M0236 ORDER OF
More informationINSTALLATION AND CARE INSTRUCTIONS
INSTALLATION AND CARE INSTRUCTIONS Vertical Applications Honeycomb Shades CONTENTS Introduction...2 Before You Begin...3 Vertical Application Parts Overview...4 Materials Required...5 Tools Required...6
More informationmila-wall (Series100) General Operating Instructions page 1 of 15
mila-wall (Series100) General Operating Instructions page 1 of 15 Step #1: Before setting up walls, lower adjustable leveling feet on each panel approximately 1". This will allow access to the threaded
More informationFrameless Fixed Panel Slider
INSTALLATION INSTRUCTIONS Frameless Fixed Panel Slider QCI-5279 SINGLE ROLLER WITH ANTI-JUMP DOUBLE ROLLERS QCI5279 Rev Page Certified 08/09/6 Tools: To install your New Shower Enclosure, you may need
More informationMirage Installation Manual
Mirage Installation Manual General Information This installation manual provides necessary information for the safe installation of the Mirage product. WARNING: Failure to follow the instructions in this
More informationED1300/1300F SERIES CONCEALED VERTICAL ROD DEVICE INSTALLATION INSTRUCTIONS
ED1300/1300F SERIES CONCEALED VERTICAL ROD DEVICE INSTALLATION INSTRUCTIONS Ver.2 1300 SERIES CONCEALED VERTICAL ROD DEVICE Top Strike Latch Screws Strike Screws Release Plunger Top Latch Plunger Screws
More informationSeries 1100 Aluminum Door Canopy
Series 00 Aluminum Door Canopy with Support Arms It is our recommendation that you read instructions carefully prior to assembly and installation. Series 00 with Support Arms MOUNTING BAR (A) TOP TRIM
More informationWooden Frame Type Instruction Manual
Wooden Frame TypeInstruction Manual Thank you for selecting our product. Before starting installation, please read this manual thoroughly to ensure correct installation. Please keep this manual at hand
More informationFor installation assistance, contact SARGENT at DOORS SHOWN HERE SWING IN FOR ILLUSTRATION PURPOSES ONLY.
SARGENT Installation Instructions for LP8600 x LR8600 & 12-LP8600 x 12-LR8600 Series Low Profile Panic and Fire Exit Devices on Double Egress & Double Doors or LS8600 & 12-LS8600 Low Profile Exit Device
More information1200 SERIES 2 PANEL DOOR rev.1 DETAILED INSTALLATION INTRUCTIONS
1200 SERIES 2 PANEL DOOR 10.2013 rev.1 DETAILED INSTALLATION INTRUCTIONS GENERAL: Door elevations shown in these instructions are as viewed from the outside. X denotes the active or moving panel(s). O
More informationSingle Sided Height Adjustable Benching
Single Sided Height Adjustable Benching Bit Holder Power Drill Long # Square Drive Bit 5mm Hex Drive Bit T-30 Torx Drive Bit Hex Key -.5mm (Provided) SERIES 5 Hex Key - 3mm Socket Adaptor (or) If you have
More informationINSTALLATION INSTRUCTIONS VENETIAN 84" SLIDING SHOWER DOOR SYSTEM (180º INSTALLATION)
INSTALLATION INSTRUCTIONS VENETIAN 84" SLIDING SHOWER DO SYSTEM (180º INSTALLATION) 28539 Industry Drive, Valencia, CA 91355 Toll Free Phone: (877) 728-3874 Toll Free Fax: (888) 440-9567 Phone: (661) 775-1675
More informationTOOL LIST FOR TAILGATE HIDDEN LATCH & LINK ASSY FOR FORD FLARESIDE TRUCKS
TOOL LIST FOR TAILGATE HIDDEN LATCH & LINK ASSY FOR 53-87 FORD FLARESIDE TRUCKS Vise Grip Clamps C-clamps Sharpie Marker Ball Peen Hammer Center Punch 3/8 or 1/2 Drill 5/32, 7/32, 9/32, and 3/8 Drill Bits
More informationASSEMBLY INSTRUCTIONS FOR SL500A AND SL500AL
ASSEMBLY INSTRUCTIONS FOR SL500A AND SL500AL January 2013 The SL500A is a square upright glass cabinet with a single hinged lockable door. It has five adjustable shelves plus the base. It also has an optional
More information*D-1030* 1 PARTS CHECK 8 REVERSING INSTRUCTIONS F-XX-C & XX-C D Customer Service. Installation Instructions. Exit Devices
*D-1030* D-1030 F-XX-C & XX-C Exit Devices Installation Instructions 8 REVERSING INSTRUCTIONS TO REVERSE THE HANDING OF A (F)XX-C DEVICE NOTE: TO REVERSE TRIM, REFER TO SEPARATE INSTALLATION SHEETS. 1
More informationVertical Honeycomb Shades
Step by Step Installation Instructions Vertical Honeycomb Shades Customer Service 800.248.8888 or visit us online at smithandnoble.com Thank you for purchasing from Smith+Noble. Your new shades have been
More informationFIG. #1 - ASD-90 & USD-90 Shower Door Assembly
Installation Instructions for the Accent/Euro Collection FIG. #1 - ASD-90 & USD-90 Shower Door Assembly #1021 #1021 1 23 25 2 #1020 6 5 12 #1020 9 24 9 8 Hinge Assembly 2109, 2201, 2212, 2213, 2220 7 Please
More informationInstallation Guide 2016
Installation Guide 2016 BUILDERS EDGE INSTALLATION GUIDE This guide will show you the products of the Builders Edge family. It provides specific installation steps and application details. Our main goal
More informationEmagiKit. Privacy Pod Plus. Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY
EmagiKit Privacy Pod Plus Quiet. Easy. Affordable. INSTRUCTIONS ASSEMBLY DIMENSIONS AND COMPONENTS 47 47 Ceiling Unit 2-B 2-L 2-R Glass Door Corner Trim Door Handle 90 Adjustable Height Work Surface 1-B
More informationMantelMount. TM1A Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS
MantelMount TMA Installation Instructions IMPORTANT SAFETY INSTRUCTIONS - SAVE THESE INSTRUCTIONS TM Thank you for choosing the MantelMount television wall mount. Please read this entire manual before
More informationICU TRACKLESS SLIDING DOOR
Interior View 0 Installation Instructions Tools Required: Screwdrivers Small Straight (Flat Blade) - for Terminal Block wiring # Phillips (Crosspoint) - for various #8, #0, and #4 screws Wrenches / Sockets
More informationMelamine Plastic Laminate. Toilet Partition Installation Manual
Melamine Plastic Laminate Toilet Partition Installation Manual PHONE: FAX: 1-866-317-2786 ATTENTION DO NOT MIX FASTENER PACKS EACH FASTENER PACK HAS THE NECESSARY BOLTS, BARRELS AND SCREWS TO INSTALL THE
More informationTOOLS REQUIRED FOR ASSEMBLY. Rubber Mallet or Plastic Tip Hammer PARTS REQUIRED FOR ASSEMBLY OF SINGLE ENTRY STARTER.
TOOLS REQUIRED FOR ASSEMBLY Rubber Mallet or Plastic Tip Hammer Top Cover Support PARTS REQUIRED FOR ASSEMBLY OF SINGLE ENTRY STARTER Back Stop Divider Closed 'L' Upright Slotted Reinforcement Support
More informationHow To Measure Your Finished Opening
3000 Series Bifold Doors How To Measure Your Finished Opening MEASURE FROM RIGHT TO LEFT 2 PLACES (WIDTH) MEASURE FROM TOP TO BOTTOM 2 PLACES (HEIGHT) Tools Required for Assembly: Tools Needed: Phillips
More information* * 98/9950WDC. Fire-Rated Devices include these. additional components. 1-Point Latch (LBL)
*24739468* 24739468 98/9950WDC Installation Instructions 1-Point Latch (LBL) Fire-Rated Devices include these additional components Metal Edge Wrap required for 60 and 90-minute applications 2-Point Latch
More informationInstalling Electronic Media Storage Components into Lateral File Cabinets
Steelcase, Inc. Grand Rapids, MI 49501 U.S.A. 1-888-783-3522 Installing Electronic Media Storage Components into Lateral File Cabinets 830-CH-9 830-CH-12 830-CH15 836-CH-9 836-CH-12 836-CH-15 842-CH-9
More informationFrameless Inline Door With Return QCI5263
INSTALLATION INSTRUCTIONS Frameless Inline Door With Return QCI5263 WALL MOUNT HINGES FRAMELESS DOOR / PANEL / RETURN PANEL QCI5263 REV. 0 Page 1 Certified 06/17/2016 Parts List with wall mount hinges
More informationInstallation Instructions for Vista Air Vertically Folding Walls
Installation Instructions for Vista Air Vertically Folding Walls Use these instructions in conjunction with your shop drawings to see the specifics that are particular to the model you are installing.
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More informationDublin Stalls Installation Instructions
Dublin Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 9/13/17 Part Identification Round Track Bracket (4) (Not Painted) Round
More informationBox Track INSTALLATION INSTRUCTIONS
Box Track INSTALLATION INSTRUCTIONS BOX TRACK Recommended Tools Level Tape Measure Pencil Drill with 1/8, and 1/4, Drill Bits, Phillips Bit and Slotted Bit Socket Wrench with 9/16 Socket 9/16 and 5/8 Wrench
More informationSeries 1500 Aluminum Door Canopy
Series 500 Aluminum Door Canopy with Sidewings It is our recommendation that you read instructions carefully prior to assembly and installation. Series 500 with Sidewings mounting bar (A) top trim (B)
More informationPROFILE Flat Panel Console System Installation Manual
PROFILE Flat Panel Console System Installation Manual Table of Contents Page Introduction... 2 Important Safety Information...3, 4 Installation Overview... 4, 5, 6 Single Sided/Single Unit... 7 Double
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS SOLID PHENOLIC TOILET PARTITIONS 1080 DuraLineSeries Class-A Fire Rated Includes Institutional Hardware Option.67 IMPORTANT: Storage and Handling Information on last page. Review
More informationBARN DOOR HARDWARE KIT
INSTALLATION GUIDE Main Components x1 Rail x5 Wall Spacer x2 Anti-jump Block x2 Bent Strap x1 Right Stopper x1 Left Stopper x5 5/16 (8mm x 60mm) Carriage Bolt x5 5/16 (8mm x25mm) Anchor x5 5/16 (8mm x
More informationTrendWall Floor-To-Ceiling Panels Installation Instruction
TrendWall Floor-To-Ceiling Panels Installation Instruction TrendWall Components Covered by this Instruction: Crown (and accessories) Floor Plate Solid Panel Filler Panel Wall Channel Door Section Pilaster
More informationJEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT
JEEP JK ( 5 DOOR ) SLIMLINE II - FULL TRAY EXTREME RACK KIT FAJK001 / KRJW014T INSTALL TIME: 2.5 Hours NOTE: Your Jeep JK (5 Door) Extreme Roof Rack Kit consists of four boxes. (1) the Tray, (2) the Roll
More informationBX2173 Installation Instructions Ford Focus (including the 2.3L engine) 2003 Ford Focus SVT
BX2173 Installation Instructions 2000-04 Ford Focus (including the 2.3L engine) 2003 Ford Focus SVT Serial No. The front fascia, coolant line bracket and anti-pollution devices are removed for baseplate
More informationINSTALLATION INSTRUCTIONS CRL JACKSON
INSTALLATION INSTRUCTIONS CRL JACKSON 3185 MID-PANEL CONCEALED VERTICAL ROD PANIC EXIT DEVICE crlaurence.com Phone: (800) 421-6144 Fax: (866) 921-0531 crlaurence.com usalum.com crl-arch.com 11M0252 ORDER
More informationReplacing the Reciprocator on the SWF Compact Series Machine (601C and 1201C)
Follow the instructions below to replace the reciprocator in the SWF Compact series machines. The tools required can be found in the tool kit that came with the machine. Preparation 1. First, place the
More informationAluminum Railing Gate Kit
BOM-34115787 Aluminum Railing Gate Kit INSTALLATION INSTRUCTIONS Read all instructions prior to installing product. Refer to manufacturers safety instructions when operating any tools. To register your
More informationVinyl Sliding Glass Door Assembly Instructions
Vinyl Sliding Glass Door Assembly Instructions SERIES SGD 5470/5570 Para instrucciones en español, visite: http://bit.ly/pgtassemblyinstructions Parts List ITEM 4 5 6 7 8 9 0 4 5 6 7 8 SGD 5470/5570 PARTS
More informationFrameless Inline Door With Return QCI5128
INSTALLATION INSTRUCTIONS Frameless Inline Door With Return QCI5128 WALL MOUNT HINGES FRAMELESS DOOR QCI5128 REV. 0 Page 1 Certified 06/20/2016 3 panel - Parts List KEY DESCRIPTION PART NUMBER QTY KEY
More information3-LITE PATIO DOOR INSTALLATION INSTRUCTIONS
3-LITE PATIO DOOR INSTALLATION INSTRUCTIONS IMPORTANT: Read the instructions and familiarize yourself with the door parts and pieces before beginning assembly and installation. TOOLS NEEDED: Tape Measure
More informationMartin Yale 7000E Guillotine Cutter
Martin Yale 7000E Guillotine Cutter Blade Leveling Guide Provided By http://www.mybinding.com http://www.mybindingblog.com Blade Removal, Installation and Leveling for the 7000E Disclaimer The following
More informationFrameless Fixed Panel Slider QCI5279
Frameless Fixed Panel Slider QCI5279 F AB GLASS AND MIRROR www.fabglassandmirror.com Call: +1 888-474-2221 Fax: (614)-334-4919 Office Timing: 8:30-18:00 EST info@fabglassandmirror.com Frameless Fixed Panel
More informationASSEMBLY GUIDE. Mia Narrow Bookcase
ASSEMBLY GUIDE Mia Narrow Bookcase Components: Upon unpacking your bookcase from it s delivery box, you should have the pieces shown. Follow the steps on the next pages to assemble your new bookcase. Step
More informationSiding Components. Installation Guide
Siding Components Installation Guide 2016 MID-AMERICA SIDING COMPONENTS INSTALLATION GUIDE This guide will show you the products of the Mid-America Siding Components family. It provides specific installation
More informationInstallation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens
Installation and Assembly - Universal Articulating Swivel Double-Arm for 42" - 60" Plasma Screens Models: PLAV 70-UNL, PLAV 70-UNL-S PLAV 70-UNLP, PLAV 70-UNLP-S R This product is UL Listed. It must be
More information1/4 FRAMELESS DOOR WITH INLINE PANEL 1413A-1713A-1813A
1/4 FRAMELESS DOOR WITH INLINE PANEL 1413A-1713A-1813A F AB GLASS AND MIRROR www.fabglassandmirror.com Call: +1 888-474-2221 Fax: (614)-334-4919 Office Timing: 8:30-18:00 EST info@fabglassandmirror.com
More informationAssembly Instructions
InTandem Table System November 20 InTandem Table System - Worksurface #4 x/" 4 wood screw power beam Tools Provided T-0 Extended Torx Driver T-25 Torx Driver Additional Tools Required Soft protective
More information4-lite Patio Door. Installation Instructions
4-lite Patio Door Installation Instructions IMPORTANT: Read the instructions and familiarize yourself with the door parts and pieces before beginning assembly and installation. Note: Only the 5-0 x 6-8
More informationSeries----SP3600A SHOWER DOOR
Series----SP3600A SHOWER DOOR INSTALLATION INSTRUCTIONS Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences. The Exploded Diagram
More informationFrameless Bypass Slider
INSTALLATION INSTRUCTIONS Frameless Bypass Slider QCI-5301 Heavy Glass Bypass Slider with Exposed Rollers QCI5301 Rev 0 Page 1 Certified 11/1/2016 Tools: To install your New Shower Enclosure, you may need
More information4600 Series Rim Narrow Stile Exit Device Installation Instructions I-ED01162
DEVICES COVERED IN THIS DOCUMENT: 4600 Series Rim Panic Narrow Stile Exit Device 4600 Series Rim Fire Narrow Stile Exit Device OVERVIEW Outside of Door RHR LHR Inside of Door APPLICATIONS 4950 BLADE STOP
More informationGared Pro Portable Backstop
Models: 5016, 5017, & 5018 Installation, Operation and Maintenance Instructions Please read all instructions before attempting installation or operation of these units PUBLICATION NO. 551754436 SAVE THESE
More informationPet Door Panel Installation Manual
Pet Door Panel Installation Manual 400-558-1 1 4/3/03, 3:26 PM Components: Pet Door Panel Panel Latch Assembly Foam Weather-stripping Glass Sweep (4) Binding Posts (6) #6 x 1/2 Sheet Metal Screws (4) 8-32
More informationShetland Stalls Installation Instructions
Shetland Stalls Installation Instructions RAMM Horse Fencing and Stalls 13150 Airport Hwy. Swanton, OH 43558-9615 1-800-434-8456 Rev. 1/9/18 Before you start Kit can accommodate up to 12 wide stall front
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS TOOLS REQUIRED Rechargeable, variable speed drill 3/8 diameter drill bit 3 Robertson bits #0, #1 and #2 Slot screwdriver Non marring hammer with 1 head Level Caulk or sealant
More informationINSTALLATION INSTRUCTIONS INS T A L L A TIO N INS T R U C TIO N S THE MAVERICK HANGER R H
INS T A L L A TIO N INS T R U C TIO N S THE MAVERICK HANGER 10.6.2016 PARTS INSTALLATION SPECIFICATIONS AND TOOLS INSTRUCTIONS 2-1/4" 2-7/8 11-3/8" 1/4" 2-1/8 PARTS INSTALLATION AND INSTRUCTIONS TOOLS
More information