This section describes the design requirements and materials/products for door hardware.
|
|
- Kelly Shelton
- 5 years ago
- Views:
Transcription
1 Facilities Division Standards Section Door Hardware SUMMARY This section describes the design requirements and materials/products for door hardware. DESIGN REQUIREMENTS Coordinate with the McCarran Lock Shop. The specifications shall include a requirement for a Pre-Installation Conference to read as follows: Prior to the installation of hardware, manufacturer s representatives for all hardware specified shall arrange and hold a jobsite meeting to instruct the installing contractor s personnel on the proper installation of their respective products. A letter of compliance, indicating when this meeting is held and who is in attendance shall be sent to the Owner. A representative of the Facilities Division must attend this meeting. MATERIALS/PRODUCTS A. BUTTS AND HINGES Type McKinney Hager Stanley Type 1 T4A3795 OB1262 CB268 Type 2 TA2714 OB1279 CB179 Type 3 TA2314 OB1191 CB191 Type 4 T4A3786 OB1168 CB168 Type 5 T4A3386 OB1199 CB Application: Exterior out-swinging doors Type 2, 3, 4 or 5 x NRP Exterior in-swinging doors and vestibule doors Type 4 Interior doors with closers Type 2 or 4 Interior doors over 36 inches wide Type 4 Interior doors 36 inches or less without closer Type 2 NRP (non-removable pins) required on all exterior out-swinging lockable doors.
2 3. Provide 2 - hinges per leaf for openings through 60 inches high. Provide 1 - additional hinge per leaf for each additional 30 inches in height or fraction thereof. Provide 4 hinges (2 per leaf) on Dutch doors up to 90 inches in height. B. ELECTRIC HINGES McKinney Model QC with MG-16 motar guard. 2. Standardized wire colors and concealed plug connectors to accommodate up to 12 wires. C. CONTINUOUS GEARED HINGES McKinney Pemko Markar MCK-12HD FM83SLFHD No Equal MCK-25HD FM83HD FM Model depends upon the type, inset, and thickness of the door specified. D. FLUSH BOLTS AND DUSTPROOF STRIKES McKinney Rockwood Door Controls Flush Bolt MCK Automatic Flush Bolt MCK NH Automatic Flush Bolt MCK NH Dustproof Strike MCK On Non-labeled Openings provide 2 flush bolts for inactive leaf of pairs of locked and latched doors. Locate the centerline of top bolt not more than 78 inches from finished floor. Provide dustproof strike for bottom bolt. 3. On Labeled Openings provide automatic flush bolt set, as applicable, for inactive leaf of pairs of doors. Provide dustproof strike for bottom bolt. E. LOCKSETS - MORTISE 1. Acceptable Manufacturer and Series: Manufacturer Corbin/Russwin Series ML2000 DSA Series 626 Finish 2. Locksets must meet the requirements of ANSI/BHMA A , Operational Grade 1, and Security Grade Backsets shall be 2-3/4 inches.
3 5. Provide wrought boxes and strikes with proper lip length to protect trim but not to project more than 1/8 inch beyond trim, frame or inactive leaf. Where it is required, provide open back strike and protected to allow practical and secure operation. F. EXIT DEVICES 1. Acceptable Manufacturer and Series: 2. Where a lever trim is required, provide a lever design to match lockset levers. 3. Provide cylinders for exit devices with locking trim and cylinder dogging. 4. Provide keyed removable mullions. 5. Provide a RX (request to exit) internal SPDT switch in each exit device. G. KEYING Von Duprin 99 Series 33 Series 1. Provide 6 pin H0-1 keyway, 0 bitted, or 6 pin H0-2 keyway 0 bitted, or 6 pin H0-4 keyway, 0 bitted. Note: Selection will be identified at the Early Design Meeting based on the project location by the DOA Lockshop. 2. The Owner will key all cylinders. H. DOOR TRIM McKinney Rockwood Trimco Push Plate MCK x Push Plate MCK x Push Bar MCK15747 BF Pull MCK Pull MCK Pull MCK Edge Guard MCK KE All push plates shall be 6 inches by 16 inches. Where the width of the door strike stile prevents the use of a 6 inch wide plate, provide a plate one inch less than the width of the stile, but not less than 4 inches in width. 3. Kick plates and armor plates shall be a minimum of inches thick, beveled 4 edges. At single doors provide width 1-1/2 inches less than the door width on the stop side and one inch less than the door width on the face side. At pairs of doors provide width one inch less than the door width on both sides. Minimum height of kick plates and armor plates shall be 10 inches. 4. Edge guards shall be a minimum of inches thick, stainless steel, and 42 inches high.
4 I. COORDINATORS 1. Acceptable Manufacturers and Series: McKinney Rockwood Door Controls MCK1600 Series 1600 Series Provide coordinators for labeled pairs of doors equipped with automatic flush bolts and those with vertical rod/mortice lock fire exit device combinations with astragals. 3. Provide filler bars for total opening width, closer mounting brackets, carry bars, and special preparation for top latches. J. DOOR CLOSERS 1. Acceptable Manufacturer: LCN Provide heavy duty, cast iron body. K. OVERHEAD STOPS 1. Acceptable Manufacturer: LCN 2. Overhead stops must match door closers. 3. Provide overhead stops on doors that swing more than 140 degrees before striking a wall. L. WALL STOPS AND HOLDERS McKinney Rockwood Trimco MCK WX MCK WV MCK Floor and base stops shall be used only where absolutely unavoidable. M. THRESHOLDS McKinney Pemko Zero MCK272A 272A 546A
5 2. Equal products by Reese Enterprises and National Guard Products are also acceptable. 3. Where thresholds occur at openings with one or more mullions, they shall be cut for the mullions and extended continuously for the entire opening. N. WEATHERSTRIPPING 1. Acceptable Manufacturers and Type: McKinney Pemko Zero Sweeps MCK18062CNP 18062CNP 8192A Jambs MCK303AV 303AV 328A Door top drips MCK346C 346C 11A 2. Rain drips shall be no less than full frame width. O. GASKETING McKinney Pemko Zero MCKS88D S88D Equal products by Reese Enterprises are also acceptable. 3. Where smoke gasket is required, provide MCKPK55D. 4. Provide gaskets for all 20-minute doors that are designated for smoke and draft control. 5. Where frame applied intumescent seals are required by the manufacturer, provide gaskets that comply with UBC 7-2, 1997 and UL 10C positive pressure tests. P. MAGNETIC HOLDERS Sargent Rixson-Firemark HES 1561 FM The voltage shall be verified with the Electrical Contractor. Q. FASTENERS 1. Including, but not limited to, wood or machine screws, bolts, nuts, anchors, etc. of proper type, material, and finish required for installation of hardware. 2. Use Phillips head for all exposed screws. Aluminum screws are not allowed. 3. Provide self-tapping (TEC) screws for the attachment of sweeps and stop-applied weatherstripping only.
6 R. FINISHES AND MATERIALS 1. Finishes shall be as follows: a. Butts on Out-swinging Exterior Doors: US32D (BHMA 630) on Stainless Steel b. Butts on Interior Doors and In-swinging Exterior Doors: US26D (BHMA 652) on Steel c. Continuous Hinges: US28 (BHMA 628) on Aluminum d. Flush Bolts: US26D (BHMA 626) on Brass or Bronze e. Exit Devices: US26D (BHMA 630) on Stainless Steel f. Locks and Latches: US26D (BHMA 626) on Brass or Bronze g. Push Plates, Pulls, and Push Bars: US32D (BHMA 630) on Stainless Steel h. Coordinators: USP (BHMA 600) on Steel i. Kick Plates, Armor Plates, and Edge Guards: US32D (BHMA 630) on Stainless Steel j. Overhead Stops and Holders: US26D (BHMA 626) on Brass or Bronze k. Closers (Surface Mounted): Sprayed Aluminum Lacquer l. Latch Protectors: US32D (BHMA 630) on Stainless Steel m. Miscellaneuos Hardware: US26D (BHMA 626) on Brass or Bronze
Ives Pemko Hager 112HD FMSLFHD HD 224HD FMHD HD 210HD FSHD HD 157HD FSCPHD HD
PART 1 - PRODUCTS 1.1 FASTENERS A. All exposed fasteners shall be Phillips head or as otherwise specified, and shall match the finish of the adjacent hardware. All fasteners ex-posed to the weather shall
More informationSECTION FINISH HARDWARE
SECTION 08710 PART I - GENERAL 1.01 DESCRIPTION A. Scope: Work under this Section shall include all materials and installation necessary to provide Finish Hardware as shown and detailed on the Drawings
More informationDOOR SAVERS AVAILABLE IN STEEL, STAINLESS STEEL (32D), BRIGHT BRASS (3), BRONZE (10) AND OIL RUBBED BRONZE (10B)
SAVERS K1 : 9 High For cylindrical locksets 2-1/8 bore, 2-3/8 and 2-3/4 backsets K 188 2-3/8 1-3/8 K 184 2-3/8 1-3/4 K 148 2-3/4 1-3/8 K 144 2-3/4 1-3/4 K5 144 5 SPECIFY K3 : 9 High For cylindrical locksets
More informationConstruction Standards PAGE
Construction Standards PAGE 087100-1 SECTION 087100 - PART 1 - GENERAL 1.1 M.S.U. ISSUES A. On interior doors, do not install lights that extend below the level of the top of the mounting of the exit device
More informationEncore 20 Min. FIRE RATED DOORS WARNOCK HERSEY ENCORE - STANDARD PANEL - 20 MIN. RATING
Encore 20 Min 20 Minute (Positive Pressure) - Category B Manufacturing Specifications MAXIMUM SIZES All doors shall have a minimum thickness of 1-3/4" + 1/16" Single Swing: 4/0 x 8/0 Standard Pair: 8/0
More informationPUSH BAR EXIT DEVICES CROSS BAR EXIT DEVICES NARROW STILE EXIT DEVICES FEATURING LCWD STRIKES... 20
Flat Goods Section TABLE OF CONTENTS EXIT DEVICES PUSH BAR EXIT DEVICES N1500 Heavy Duty Rim Exit Device N1550 Rim Exit Device... 6 N1650 Fire Rated Heavy Duty Exit Device N1700(F) Vertical Rod Heavy Duty
More informationInfinity 20 Min. FIRE RATED DOORS WARNOCK HERSEY INFINITY - STANDARD RAISED - 20 MIN. RATING SOFTWOOD STILE
Infinity 20 Min Note: 20 Minute (Positive Pressure) Category A & B Manufacturing Specifications MAXIMUM SIZES All doors shall have a minimum thickness of 1-3/4" + 1/16" Single Swing: 4/0 x 9/0 Standard
More informationSECTION DOOR HARDWARE
PART 1 - GENERAL 1.1 DESCRIPTION SECTION 08 71 00 1. Use this section only for NCA projects. 2. Delete between // --- // if not applicable to project. Also delete any other item or paragraph not applicable
More information350/500 Heavy Wall TM IR Entrances
SEPTEMBER, 207 FEATURES Hurricane Resistant Product Blast Mitigation Product Features 50 Heavy Wall TM IR medium stile has vertical stiles, top and 6-/ (65.) bottom rails 500 Heavy Wall TM IR wide stile
More informationDIVISION 8 DOORS AND WINDOWS. 1. Exterior and interior single doors shall be 1-3/4 inch thick, 3 feet wide, and 7 feet high, minimum.
8.01 DOORS AND FRAMES (12-2-02) A. Doors DIVISION 8 DOORS AND WINDOWS 1. Exterior and interior single doors shall be 1-3/4 inch thick, 3 feet wide, and 7 feet high, minimum. 2. Where required for maintenance
More informationM O R T I S E L O C K S
MORTISE LOCKS lock design M certification / compliance Locks comply with UL 10B, Fire Tests of Door Assemblies, and UL 10C, Positive Pressure Fire Tests of Door. Door Assemblies and the Uni form Building
More informationJune, 2018 Page 1 of 12
Part 1 General 1.1 Summary.1 Unless otherwise indicated, follow the standards below when specifying hardware work. These standards are not intended to restrict or replace professional judgment..2 Unless
More informationFINISH HARDWARE. UNIVERSITY CONTACT: Mark Golden, Manager, Structural Services (302)
FINISH HARDWARE UNIVERSITY CONTACT: Mark Golden, Manager, Structural Services (302)831-2935 PART 1 GENERAL 1.01 GENERAL PROVISIONS A. The drawings and General Provisions of the contract, including the
More information350/500 HEAVY WALL TM IR ENTRANCES 1
JUNE, 202 30/00 HEAVY WALL TM IR ENTRANCES FEATURES Blast Mitigation Product Features 30 medium stile has 3-/2" vertical stile, 3-/2" top and 6-/2" bottom rail 00 wide stile has " vertical stile, " top
More informationTHE JAMES RUSHTON EARLY LEARNING AND FAMILY SUCCESS CENTER #2616 ADDENDUM ONE
SECTION 08 7100 DOOR HARDWARE PART 1 - GENERAL 1.1 RELATED DOCUMENTS A. Drawings and general provisions of Contract, including General and Supplementary Conditions and Division 1 Specification Sections,
More informationMetal Sound Retardant Door Hardware Information Bulletin
574 West Otterman Street Greensburg, PA 15601 Toll Free: (800) 979-7300 Local: (724) 834-7300 Fax: (724) 830-2871 Email: overly@overly.com DOOR COMPANY Metal Sound Retardant Door Hardware Information Bulletin
More informationContinuous Geared Hinges
Standard Lengths Cal-Royal continuous hinge length provides for actual threshold clearance, head clearance and door height allowances for carpeting. Other lengths may be ordered as non-standard items.
More informationMasonry Frames Interior/Exterior* Drywall Frames Interior**
Masonry Frames Interior/Exterior* Step your frame: Wire Masonry Anchor Combo Stud Anchor Existing Opening Anchor Hollow Metal 5-3/4" Standard* Frame Includes: 6 gauge - cold rolled steel - primed galvanneal
More informationFINISH HARDWARE FOR NEW FACILITIES. A. Provide finish hardware including necessary accessories.
SECTION 08710 FINISH HARDWARE FOR NEW FACILITIES PART 1 GENERAL 1.01 SUMMARY A. Provide finish hardware including necessary accessories. B. Related Sections: 1. 06100 - Carpentry. 2. 08110 - Steel Doors
More informationExit Device 5820 SERIES GRADE 1 PUSH BAR SPECIFICATIONS HEAD COVER OPTIONS STRIKES APPLICATION.
Exit Device 5820 SERIES GRADE 1 PUSH BAR 5820F Fire-Rated Mortise Lock Exit Device 5820FSF Failsafe Electric Mortise Exit Device 5820FS Failsecure Electric Mortise Exit Device HEAD COVER OPTIONS HC-1 HC-2
More information350/500 IR Entrances. Features
OCTOBER, 05 Features FEATURES Blast Mitigation Product 50 IR medium stile has vertical stiles, top and 6-/" (65.) bottom rails 500 IR wide stile has (7) vertical stile, (7) top and 6-/" (65.) bottom rail.
More information350/500 IR Entrances. Features
SEPTEMBER, 07 Features FEATURES Blast Mitigation Product 50 IR medium stile has vertical stiles, top and 6-/" (65.) bottom rails 500 IR wide stile has (7) vertical stile, (7) top and 6-/" (65.) bottom
More informationSTC 46 3-Sided Paired Frame (Double Rabbet Only)
(Toll Free) Phone 866-452-1845 Fax 910-452-1848 STC 46 3-Sided Paired Frame (Double Rabbet Only) FRAME PART DIMENSIONS E E THROAT THROAT MINIMUM 3 5/16" MAXIMUM 13" D A=Jamb Depth MINIMUM 4 5/16" MAXIMUM
More information55 Series Exit Device
55 Series Exit Device 55 Exit Devices Index Introduction........................................................................... 3 Exit Hardware Rim device............................................................................
More informationYour global resource for quality commercial door hardware. Euroline Catalog Euroline Catalog
Your global resource for quality commercial door hardware. Catalog Catalog More for your door than any other brand. TM Industry-Leading Service For more than 158 years, Hager Companies has led the industry
More informationFinish Hardware. Contents. Section 10
Section 10 Finish Hardware Contents 10.0.0 Introduction to contents 10.1.0 Door hinges (types and illustrations) 10.2.0 Locksets and latchset configurations and functions 10.3.0 Heavy-duty mortise cases,
More information3000 Series Exit Devices Premier Product
00 000 Series Exit Devices Premier Product Certification & Compliance: ANSI/BHMA A56., Grade ANSI A7. Accessibility Code Underwriters Laboratories (UL and CUL) listed for accident hazard (panic) standard.
More informationDIVISION Hardware
FORMAT 1. Technical specifications content and numbering system shall be based on the most current CSI Master Format. BASIS OF DESIGN 1. APSU design standards shall not replace fully developed, project
More informationSolid Core Wood Door / Steel Frame Packages
Solid Core Wood Door / Steel Frame Packages No Label - Interior Packages Machined for one (1) cylindrical lock and three (3) hinges at Republic locations 1-3/4 Solid Core Birch 1-3/4 Solid Core Oak 3/0
More informationFEATURES. TownSteel Architectural Hardware MFG
TownSteel Architectural Hardware MFG TownSteel Inc. Quick Ship Guide Quick Ship Products on the road to you within 48 hours of receipt of purchase order and upon approval of credit. Terms and conditions
More informationVictory Fire Door Inspections
Vickie Evans, FDAI Over 30 years in door and hardware industry DHI instructor and Education Advocate Certified Fire Door Inspector To compartmentalize a building Deter the spread of smoke and flames Fire
More informationED8000 Series. Pushpad Exit Devices Parts Manual
ED8000 Series Pushpad Exit Devices Parts Manual Table of Contents ED8200A Rim Exit Device...4 ED8200(B) Rim Exit Device...6 ED8400A Surface Vertical Rod Exit Device...8 ED8400 Surface Vertical Rod Exit
More informationTable of Contents Holders & Stops
Copyright 2003, 2007, 2009-2018, Sargent Manufacturing Company, an ASSA ABLOY Group company. All rights reserved. Table of Contents Overview.... 1 General Information.... 2 Features and Details.... 3 590
More information8000 SERIES SERIES HEAVY-DUTY MODELS
GRADE 1 ARCHITECTURAL TYPE EXIT DEVICES 8000 SERIES SERIES HEAVY-DUTY MODELS FEATURES All devices are non-handed design Slight pressure on device touch bar will retract latch(s) for immediate exit Auxiliary
More information55 Series. Exit device
55 Series Exit device Introduction The proper selection and application of exit hardware, in addition to safety, are major concerns to all responsible manufacturers. Exit devices are a critical part of
More information6200 Series. System Components Series Electric Strikes
6200 Series Strikes for Mortise or Cylindrical Devices Models 6210, 6211, 6211AL, 6211WF, 6212, 6212WF, 6213, 6214, 6215, 6216, 6221, 6222, 6223, 6224, 6224AL, 6225 & 6226 System Components 6200 Series
More informationIves - Residential 07 WINDOW LOCKS 2 ELBOW CATCH 25 SCREEN DOOR PULL 026 BAR WINDOW LIFT
07 WINDOW LOCKS Material Brass or Aluminum Vertical and horizontal cam action for snug non rattling fit Heavy gauge spring for long wearing action Meets ANSI A156.16 Include screws ABS-AMERICAN BUILDING
More information6200 Series. Strikes for mortise or cylindrical devices. Features and benefits. Overview. Non handed design provides greater flexibility
6200 Series Strikes for mortise or cylindrical devices Overview Features and benefits Von Duprin electric strikes are known for their reliability, durability and security. The 6200 Series is designed to
More informationStainless Steel Continuous Hinges
Stainless Steel Continuous Hinges Why Continuous? Hager Companies heavy duty stainless steel continuous hinges are designed and engineered to evenly distribute door weight along the full length of the
More information7.01. Door Hardware & Accessories
7.01 Door 7.02 Mid-Panel Concealed Vertical Rod Panic First Choice 3100 Series Exit Device 7.03 P092 Mortised Butt Hinge Both leaves of this hinge are punched and countersunk so they can be mortised into
More informationWOOD AND CLAD COMMERCIAL DOOR WOOD AND CLAD 2 1/4 COMMERCIAL DOOR. Table of Contents
WOOD AND CLAD COMMERCIAL DOOR WOOD AND CLAD 2 1/4 COMMERCIAL DOOR Table of Contents PAGE History... 2 Part Identification Wood Commercial Door XX RHRA... 3 Part Identification Wood Commercial Door Stationary
More informationIves - Residential #07 WINDOW LOCKS #2 ELBOW CATCH #25 SCREEN DOOR PULL #026 BAR WINDOW LIFT
#07 WINDOW LOCKS Material Brass or Aluminum Vertical and horizontal cam action for snug non rattling fit Heavy gauge spring for long wearing action Meets ANSI A156.16 Include screws ABS-American Building
More informationWorld s Leading Manufacturer Of Traffic Doors. Supplemental Instructions for the Single and Double Door Order Form
World s Leading Manufacturer Of Traffic Doors Supplemental Instructions for the Single and Double Door Order Form World s Leading Manufacturer Of Traffic Doors 2809 SW th Street Redmond, OR 97756 Phone:
More informationMcKINNEY Hinge Catalog Half Mortise Plain Bearing Hinges Five Knuckle Standard Weight Series (Reversible)
Half Mortise Plain Bearing Hinges Five Knuckle Standard Weight Series (Reversible) T2774 or furnished in : on hinge side specify T4774) 4 1 2 114.3.134 All 5K plain bearing standard weight half mortise
More informationDoor Closers. General Information
General Information Hager Companies offers a variety of surface door closers to meet a wide range of applications and uses. Heavy Duty, Grade 1 door closers are ideal for schools, hospitals, and other
More informationCheckmate Stops & Holders. Absolute Door Control and Entire Opening Protection
Checkmate Stops & Holders Absolute Door Control and Entire Opening Protection checkmate stops & holders TABLE OF CONTENTS General Information...3 How to Select Product...4 Options...5 Certifications...5
More informationSERIES 6000 ELECTRIC STRIKES
SERIES 6000 ELECTRIC STRIKES Electric Strikes provide remote release of a locked door. They allow the door to be opened without retracting the latchbolt. This occurs by the releasing of the electric strike
More informationTrim & Auxiliary. Table of Contents
Trim & Auxiliary At Hager Companies, we know all about the importance of adding the finishing touches to your building projects. That s why we re proud to offer more than 200 different trim & auxiliary
More informationContents. The undisputed leader in door accessory hardware /ING BuyLine 2600
08 71 00/ING BuyLine 2600 STEELCRAFT The undisputed leader in door accessory hardware. For more than 120 years Ives has produced a full line of top quality building hardware that delivers the utmost application
More informationINSTALLATION INSTRUCTIONS. Thermal Entrances AA 250/AA 425 THERMAL DOOR WITH TRIFAB 601/601T FRAMING
JANUARY, 2014 1 INSTALLATION Thermal Entrances AA 250/AA 425 THERMAL DOOR WITH TRIFAB 601/601T FRAMING INSTRUCTIONS 2 FRAME ASSEMBLY JANUARY, 2014 601442 SHEAR BLOCK BALL BEARING NRP BUTT (FACTORY APPLIED
More information4200 Series. Commercial Exit Device
4200 Series Commercial Exit Device 4200 SERIES COMMERCIAL EXIT DEVICE SUGGESTED ARCHITECTURAL SPECIFICATIONS RIM All exit devices shall be American Eagle 4200 Series rim or surface vertical rod devices.
More informationLT Series. Decorative tubular locks
LT Series Decorative tubular locks Put your confidence in the consistency of Schlage The LT Series gives you the quality you can count on from Schlage. LT Series decorative tubular locks are built from
More information2.01 Standard Entrances Description
2.01 Standard Entrances Description Description Tubelite Standard Entrances have an outstanding reputation for craftsmanship and strength. The Narrow Stile Door has a face dimension of 2 1/8" and is designed
More informationYour global resource for quality commercial door hardware. More for your door than any other brand.tm
Your global resource for quality commercial door hardware. More for your door than any other brand.tm Industry-Leading Service The Hager products you ll see in the following pages are known and used the
More informationHookbolt. Non Handed. Flat LH Bevel RH Bevel Radius Radius with Weather-strip. Radius Flat Bevel
Mortise Locks deadlatch Deadbolt Hookbolt Function: Deadbolt, Hookbolt, Deadlatch Backset: 31/32", 1-1/8", 1-1/2" Face Plate: 1"W x 6-7/8" L - Aluminum Case Dimensions: 7/8"W x 6"L x Depth specific to
More informationcustom entrances and hardware
custom entrances and hardware Table of Contents Custom Entrances (B1) Loose Hardware and Fabrication (B2) Custom Entrances and Modifications (B1) Table of Contents Entrance Door Handing page 3 CUSTOM ENTRANCES
More informationPRODUCT DATA CATALOG
PRODUCT DATA CATALOG CONTENTS PAGE STANDARD ELEVATIONS 2 STANDARD ELEVATIONS 3 DOOR SPECIFICATIONS 4 LOUVER SPECIFICATIONS 5 GLAZING SPECIFICATIONS 5 DOOR HANDING CHART 6 CLINE STANDARD HARDWARE LOCATIONS
More informationGrade 2 Medium Duty Cylindrical Key-In-Lever Lock Product Catalog. Z Series
Grade 2 Medium Duty Cylindrical Key-In-Lever Lock Product Catalog Non-Handed Catalog Rim Devices Falcon Lock Philosophy Quality locksets delivered on time is the Falcon Lock creed. Whether you re ordering
More informationMEETS ADA REQUIREMENTS!
PUSH / PULL LATCH HL-6 MEETS ADA REQUIREMENTS! HL-6/EO EXIT ONLY LATCH HL-6/EO Exit Only Latch for applications where only one side of door is used for exit or entry. Ideal for situations where the security
More information88 Series. Exit device
88 Series Exit device Introduction Your trusted solution Our brand s reputation, respect and legacy stem from that first exit device in 1908 and they continue because of the quality of Von Duprin products
More informationSeries D200 Narrow Stile Series D300 Medium Stile * D500 Wide Stile ** Standard Aluminum Swing Entrance Doors
E F C O C O R P O R A T I O N Visit us on the web at efcocorp.com IMPACT GRADE BALLISTIC GRADE Series D200 Narrow Stile Series D300 Medium Stile * D500 Wide Stile ** Manufacturer Configurations Narrow
More informationFIRE RATED DOOR AND FRAME GENERAL REQUIREMENTS
FIRE RATED DOOR AND FRAME GENERAL REQUIREMENTS These requirements apply to all fire rated doors, frames, and windows. Requirements for the installation of these assemblies are included in the Standard
More information2010 Condensed Catalog
2010 Condensed Catalog INDUSTRY-LEADING SERVICE The Hager products on the following pages are known and used the world over because of their legendary quality and practical value. But for 160 years, Hager
More informationNEW! EX, H & X SERIES PUSH-PULL WITH HIP PADDLE OR HANDLE EXTENSION FOR MOST 6000, 6600 AND 6700 MODELS J PUSH/PULL SERIES WITH JUNIOR COVER
EX, H & X SERIES PUSH-PULL WITH HIP PADDLE OR HANDLE EXTENSION FOR MOST 6000, 6600 AND 6700 MODELS EX SERIES Patent No. 5,70,7 6,96,599 H SERIES Patent No. 5,70,7 6,96,599 X SERIES Patent No. 5,70,7 6,96,599
More informationARCHITECTURAL DOOR HARDWARE ROLLER LATCHES, PADDLE HANDLES, DOOR HANDLES & BARS CATALOG
ARCHITECTURAL DOOR HARDWARE ROLLER LATCHES, PADDLE HANDLES, DOOR HANDLES & BARS CATALOG January 1, 2017 v3 West Coast Office (800) 544-4422 East Coast Office (800) 225-6737 intldoorclosers.com Index ROLLER
More informationYour global resource for quality commercial door hardware. More for your door than any other brand.tm
Your global resource for quality commercial door hardware. More for your door than any other brand.tm Industry-Leading Service The Hager products you ll see in the following pages are known and used the
More informationMortise Locks. European Mortise Locks Series EML Features Ordering String Functions Trim Sets European Profile Cylinders Specifications
2 Mortise Locks 2 c 3 4 6 9 22 24 European Mortise Locks Series EML Features Ordering String Functions Trim Sets European Profile Cylinders Specifications 2016 02 2 FSB North America European Mortise Lock
More information930 Series Mortice Exit Device
930 Series Mortice Exit Device BS EN 1125:1997+A1:2001 Classification Code 37601322B The Adams Rite 930 Series Mortice Exit Device is a life safety device which is designed to fit timber or hollow steel
More informationcondensed catalog Push Plates Door Pulls Door Stops Bolts & Latches Kick Plates Custom Designs
condensed catalog Push Plates Door Pulls Door Stops Bolts & Latches Kick Plates Custom Designs Introduction For over 60 years, Rockwood Manufacturing Company has taken pride in its reputation for producing
More information20 Series Exit Devices Accessories Mullions & Door Kits
20 Series Exit Devices Accessories s & Kits 980 Removable Bottom (2438mm) stock size Up to (3000mm) size 2-1/2" 1-1/2" 1-1/4" 3" 507 Adapter for Narrow Transom Bars Required when soffit is 1-1/4" to 2"
More informationIntroduction Exit Hardware Rim device... 4 Surface mounted vertical rod device... 6 Mortise lock device... 5
88 Exit Device INDEX Introduction... 3 Exit Hardware Rim device... 4 Surface mounted vertical rod device... 6 Mortise lock device... 5 Fire Exit Hardware Rim device... 7 Surface mounted vertical rod device...
More informationNo. 059FL. No. 251FL. No. 260FL. No. 305RE. Etruscan Bronze. Florentine Brass. Siena Brass (D) All designs available in these finishes.
SINCE 1964 No. 059FL No. 251FL No. 260FL No. 305RE 2 Etruscan Bronze (ETR) Florentine Brass (D) Siena Brass (BAS) Venetian Nickel (BPS) All designs available in these finishes. No. 309RE No. 331FL No.
More informationFIRE RATED DOOR AND FRAME GENERAL REQUIREMENTS
` FIRE RATED DOOR AND FRAME GENERAL REQUIREMENTS These requirements apply to all fire rated doors, frames, and windows. Requirements for the installation of these assemblies are included in the Standard
More informationCONTENTS. Custom Entrances and Hardware
CONTENTS A2/1 CONTENTS SECTION A2...CUSTOM ENTRANCES AND HARDWARE* PAGE PRICING EXAMPLES... A2/3 A2/4 190/350/500 BASE DOOR DOOR CHASSIS... A2/5 DOOR GLAZING/WEATHERING OPTIONS... A2/6 DOOR BOTTOM RAIL
More informationArchitectural Hardware
Architectural Hardware Surface Closers Precision Architectural Closers are designed for heavy duty commercial use. With an adjustable power tension, these closers can handle the lightest ADA Compliant
More informationARCHITECTURAL HARDWARE. Condensed Catalog
ARCHITECTURAL HARDWARE Condensed Catalog DOOR PULLS Shown are just a few of the many door pull options we have available. Visit our website or see our Full-Line catalog for the complete line of door pulls,
More information88 Series. Exit device
88 Series Exit device Introduction The proper selection and application of exit hardware, in addition to safety, are major concerns to all responsible manufacturers. Exit devices are a critical part of
More informationED3000 Series. Exit Device Parts Manual
ED3000 Series Exit Device Parts Manual Table of Contents Functions...3 ED3200 Series Rim Exit Device...4 ED3200A Series Rim Exit Device - Fire Rated...5 ED3400 Series Surface Vertical Rod Exit Device...-7
More informationProduct Catalog. hardwaresuppliers.com
Product Catalog hardwaresuppliers.com 800-33-5625 2 Table of Contents Full Mortise Hinges, Standard Weight... Full Mortise Hinges, Heavy Weight... 8 Half Mortise Hinges, Standard Weight... 8 Full Mortise
More informationSECTION A4...IMPACT RATED ENTRANCES* 350 IR/500 IR ENTRANCES ENTRANCE HARDWARE OFFERINGS... A4/5
CONTENTS SECTION A4...IMPACT RATED ENTRANCES* Impact Rated Entrances CONTENTS PAGE FINISH GROUPS... A4/3 350 IR/500 IR ENTRANCES ENTRANCE HARDWARE OFFERINGS... A4/5 A4/1 350 IR/500 IR BASE DOOR DOOR CHASSIS...
More informationDivision 08. Openings
Division 08. Openings 08 10 00. Doors and Frames 08 11 00. Metal Doors and Frames 1. All fire rated doors shall be metal. 2. Contractors shall remove all rating labels from doors/frames that are not installed
More information1800 Series. Flatbar Exit Devices. An ASSA ABLOY Group brand
, BC V3L 3B1, BC V3A 8A7, BC V3B 7W3, BC V6G 2M6 1800 Series Flatbar Exit Devices An ASSA ABLOY Group brand , BC V3L 3B1, BC V3A 8A7, BC V3B 7W3, BC V6G 2M6 introduction Yale 1800 series exit devices are
More informationWARRAntY & HInGE types
McKinney Warranty McKinney products are guaranteed to be free of defects in both workmanship and materials for a period of one year. Any bending, defacing or modification of our product after leaving the
More informationDOORS, HINGES, PIVOTS
Section Table of Contents DOORS,, PIVOTS SECTION 3 D Door Frames... 94 Doors... 94 Door Sweeps... 96 H Hinges... 95 100 N P Hinge Pins... 99 NSP Pivots... 100 Pivots... 100 Vendors ABH... 95 Adams Rite...
More informationStorefront Installation Guide INSTALLATION INSTRUCTIONS
STOREFRONT General Notes 1. Check contract documents and shop drawings, and understand and clarify any Field Verify Notes, approvals of drawings, and products required to be familiar with the project.
More information400 Toll Free: (800) Phone: (718) Fax: (718) RIXSON Overhead Holders. Closer-Holder Packages
Checkmate and Stops General Information Overhead stops are used to protect door assemblies.they cut down the wear and tear of frequency, closing mechanisms, wind gusts, abuse and vandalism. By limiting
More informationRENOVATION TO STUDENT SERVICES/HOUSING FROM HOSPITAL DAKOTA STATE UNIVERSITY MADISON, SOUTH DAKOTA
RENOVATION TO STUDENT SERVICES/HOUSING FROM HOSPITAL DAKOTA STATE UNIVERSITY MADISON, SOUTH DAKOTA KOCH HAZARD ARCHITECTS ADDENDUM DATE:. SCOPE OF THIS ADDENDUM: The following becomes a part of the original
More informationTubular Deadbolts. Deadbolt Series HDD Features Ordering String HDD Functions Trim Sets Suggested Specification
4 Tubular Deadbolts 3 4 6 8 17 Deadbolt Series HDD Features Ordering String HDD Functions Trim Sets Suggested Specification 3 12 14 16 17 Keyed Deadbolt Series KDD Features Ordering String KDD Functions
More informationMANUFACTURER & WHOLESALER OF WINLY PRODUCTS
MANUFACTURER & WHOLESALER OF WINLY PRODUCTS June 2018 ARCHITECTURAL, DESIGNER, BUILDER HARDWARE CONTENTS Finish Codes Entrance Handlesets & Lever Plate Entrance Handlesets 02 03 Multipoint Lock Gear and
More information404 Doors, Doorways, and Gates
404 Doors, Doorways, and Gates 404.2 Manual Doors, Doorways, and Manual Gates. Manual doors and doorways and manual gates intended for user passage shall comply with 404.2. 404.2.2 Double-Leaf Doors and
More informationSTC 42 3-Sided Single Frame (Double Rabbet Only)
(Toll Free) Phone 866-452-1845 Fax 910-452-1848 STC 42 3-Sided Single Frame (Double Rabbet Only) FRAME PART DIMENSIONS E E THROAT THROAT MINIMUM 3 5/16" MAXIMUM 13" D A=Jamb Depth MINIMUM 4 5/16" MAXIMUM
More informationProduct Cross Reference. Manufacturing, Inc.
Manufacturing, Inc. Overhead Holders & s Hospital Push/Pull Latches ElectroMagnetic Door Holders Electrical Power Transfer Products Aluminum Continuous Geared Hinges Stainless Steel Continuous Pin & Barrel
More informationHardware Fitting Accessories Bolts
Lever action flush bolt With slide Width: 19 mm Stroke (a): 25 mm 1 Flush bolt 1 Set of fastening material With lever arm Width: 19 mm Stroke (a): 18 mm 1 Flush bolt 1 Set of fastening material Stainless
More information.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1.
PAGE 1 PART 1 GENERAL 1.1 REFERENCE.1 Comply with the General Conditions of the Contract, Supplementary General Conditions and the requirements of Division 1. 1.2 RELATED WORK SPECIFIED ELSEWHERE.1 Installation
More informationDeadlatch 451 Series. Faceplates - Deadlatch. Strikes - Deadlatch. DeadLatch for Aluminum Stile Doors. Non-Handed. 451 NC0772 1¹ 8 Backset Deadlatch 4
Mortise Locks 185 Series Mortise Locks for Aluminum Stile Doors. Non-Handed. 185 NA0019 1¹ 8 Backset Deadbolt HB185 NB0123 Faceplates - Deadbolt FP-DB-F-NH-628 NE0000 Flat FP-DB-F-NH-313 NE0001 FP-DB-B-RH-628
More informationSteel Hawk 4300 Electrified Deadlatch (elatch)
STEEL HAWK 4300 ELECTRIFIED DEADLATCH (ELATCH) DA-1 STEEL HAWK 4300 ELECTRIFIED DEADLATCH (ELATCH) Steel Hawk 4300 Electrified Deadlatch (elatch) Operation Turn key, apply voltage, or operate handle or
More informationSECTION SWINGING AUTOMATIC ENTRANCES IN-GROUND, AUTOMATIC SWING DOOR OPERATOR CONVERTER ADAPTED TO BROOKFIELD NB-500 EXTREME DUTY OPERATOR
SECTION 084229.33 SWINGING AUTOMATIC ENTRANCES IN-GROUND, AUTOMATIC SWING DOOR OPERATOR CONVERTER ADAPTED TO BROOKFIELD NB-500 EXTREME DUTY OPERATOR PART 1-GENERAL 1.01 DESCRIPTION A. This section describes
More informationDecorative Lever Designs
Decorative Lever Designs 3 & C 4 & K 12 14 & D 15 & A 16 & B 17 50 51 52 53 54 55 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 2 www.stanleysecuritysolutions.com
More informationAstragals and Meeting Stiles
Table of Contents Split Astragals.....................................................1-2 Split Astragals with Snap Covers.......................................3 Meeting Stile Gasketing...............................................4
More informationAluminum Continuous Geared Hinges
Manufacturing, Inc. Overhead Holders & Stops Hospital Push/Pull Latches Electro-Magnetic Door Holders Electrical Power Transfer Products Stainless Steel Continuous Pin & Barrel Hinges Stainless Steel Edge
More information