What we ll be learning today
|
|
- Brenda Newman
- 6 years ago
- Views:
Transcription
1 Set Construction
2 What we ll be learning today The use, construction of, and terminology of typical scenic elements The lumber, tools, and hardware used to build these scenic elements
3 Stock Scenery Stock scenery is standardized rectangular flats (including door, window and fireplace flats) which can be easily assembled into a set. Because they are standardized, they can be quickly repainted and used in another production. The use of stock scenery can reduce the set budget for a show to the cost of paint.
4 CCA Stock Scenery CCA uses flats and platforms as our stock scenery. Flats are used as walls. Platforms are used as floors (must be weight-bearing) to create different levels (alone or with legs) or wagons which are platforms on casters (wheels). The traditional theatrical flat has a wooden frame with muslin (a canvas-like fabric) facing. All of our flats are hard flats. They have lumber facing.
5 A CCA Set Made with Stock Scenery For a show with a VERY low budget
6 Hard Flats There are 2 ways to make flats Theatrical Flats Framing lumber is laid flat Requires use of corner and joint bracing, especially when using muslin (fabric) facing Hollywood or TV Flats Framing lumber is on edge The hard facing helps keep the flat sturdy without the use of joint bracing All of our stock flats are Hollywood flats
7 Theatrical Flat
8 Flat Terminology Rail: the top and bottom, horizontal pieces of the frame Stile: the side, vertical pieces of the frame Toggle: the internal, horizontal pieces of the frame
9 Hollywood Flat
10 Discussion Theatrical vs. Hollywood Flats What are the benefits or different uses of each version?
11 Platforms Framing for a Hollywood Flat and Platforms are the same, however the lumber used is different
12 Lumber for Flats Frame 1 x3 stock lumber (usually pine) Actual size is approximately ¾ x2 5/8 or 2 ¾ Typically comes in 8-16 lengths Facing 1/4 width lauan (mahogany underlayment) Typically comes in 4 x8 sheets Actual size may vary
13 Lumber for Platforms Frame 2 x4 stock lumber Actual size is approximately 1 ½ x3 ½ Typically comes in 8-16 lengths Facing ¾ Stock Plywood Sometimes comes as 23/32 which is slightly less than ¾ Typically comes in 4 x8 sheets
14 Discussion Flats Vs. Platforms Why do we use different lumber for flats and platforms even though the construction is the same?
15 Tools for Construction Compound miter saw, aka Chop saw Used to cut long, skinny lumber Used to cut 1 x3 and 2 x4 lumber for flats and platform frames
16 Pneumatic staple gun and air compressor Staple guns come in different sizes and can use different size staples We use staples to put together flats 1 ½ or 2 for the frames, 1 for the lauan facing Tools for Flats
17 Tools for Platforms Cordless driver Using the Phillips head screw tip Use for platform frame and facing Use 2 ½ or 3 coarse thread drywall screws for frame and 1 5/8 screws to attach plywood facing
18 Discussion Screws Vs. Staples Why do you think we sometimes use screws and sometimes use staples in theatrical construction?
19 More tools and materials Wood glue to use on flat joints Tape measures for lengths of lumber cuts Measure twice, cut once!!! Pencils Triangle Square or Right Angle to make sure you have 90 degree angles in each corner
20 Router Trim overhanging edges (straight bit) or round the edges (curved bit) Finishing Tools Different router bits
21 Finishing Tools, cont. Sander for a smooth finish Belt (right) Palm (below)
22 Size of Flats and Platforms The standard stock flat and platform is 4 x8. (For a flat 8 is the height.) Various combinations of even-numbered lengths are also common e.g. 2x8, 4x4. Toggle bars (the interior braces) are placed every 2 apart.
23 Measurements for Cuts of Lumber for the Frames Because the rails (top and bottom edges) are on either side of the stiles (side edges), you will need less than 8 for the stiles. You need to subtract 2x (1x for the top rail, 1x for the bottom rail) the thickness of the lumber used for the rail from 8 to get the actual length of the cut of lumber used for the stile. The same goes for the toggle bars which are set inside the stiles. Subtract 2x the thickness of the lumber used for the stile from 4 to get the actual length of the cut of lumber used for the toggle.
24 Do the Math What size cut would the stiles be for a platform? Use 2 x4 lumber for platform frames Actual size of 2 x4 is approx. 1 ½ x 3 ½ Platform frames built with lumber on edge= 1 ½ thickness 1 ½ +1 ½ =3 Length of platform =8 = =93 or 7 9
25 Create a Cut List Cut list for a 4 x8 flat 1 x3 lumber /2 46-1/2 The lauan facing will be a full sheet and will not need to be cut
26 Key Terms Stock scenery Theatrical Flat Hollywood Flat Rail Stile Toggle (bar) Platform Wagon Caster Pneumatic Triangle Square Muslin
27 Practice In pairs, you are going to create a construction drawing and cut list of a 2x2 cubby shelf. The opening of the cubbies should be 1 tall x1 wide x1 deep. Create an orthographic projection or an isometric, oblique, or cabinet drawing. The lumber will be ¾ thick plywood, except for the backing, which will be ¼ thick lauan.
What we ll be learning today
Set Construction What we ll be learning today The use, construction of, and terminology of typical scenic elements The lumber, tools, and hardware used to build these scenic elements How to build these
More informationPinewood Derby Display Case
Pinewood Derby Display Case Optional Door Design by Neil Fern - Pack 187 Exterior Dimensions 23 ½ (H) X 10 ½ (W) X 3 ½ (D) Front Back OPTIONAL Door Finished Interior Dimensions 21 7/8 (H) X 9 (W) X 3 (D)
More informationDIY Rustic Dresser Addicted2DIY.com
DIY Rustic Dresser Addicted2DIY.com *Before beginning this project, please read through all of the plans as well as the blog post associated with this project. Always use safety precautions whenever using
More informationANA WHITE PLATFORM BED: RYOBI 2017 PROJECT #5 Page 1 of 15. Description:
Page 1 of 15 Description: We built this platform bed with storage side for our pre-teen daughter s room, and she couldn t be happier. The bed is very comfortable, and the storage piece adds style and function.
More informationx2 1/4 (6mm) Floor Anchor
INSTALLATION GUIDE Main Components x1 Rail x5 Wall Spacer x2 Anti-jump Block x2 Straight Strap x1 Right Stopper x1 Left Stopper x5 5/16 (8mm x 60mm) Carriage Bolt x5 5/16 (8mm x25mm) Anchor x5 5/16 (8mm
More informationHAND TOOL NOTES For each tool picture and name, please write what it s used for. You will have a quiz on this.
HAND TOOL NOTES For each tool picture and name, please write what it s used for. You will have a quiz on this. Tool (Name & Nut drivers Speed Square Adjustable Bevel Square CONSTRUCTION TOOLS: Tool (Name
More informationWood Sawhorse. Description: Materials: Tools: Drawing/Photo: Name: Date:
Wood Sawhorse Name: Date: Description: The project is a wood sawhorse that can be used for workspace for future projects. It requires layout and wood working/construction skills. Materials: 4-1x6x30 DF
More informationPROJECT PLANS ROLLING LAUNDRY SORTER
R PROJECT PLANS ROLLING LAUNDRY SORTER Sorting laundry certainly doesn t rank high on anyone s list. So, anything that makes this task easier is welcome. If that functionality can be mixed with a bit of
More informationBARN DOOR HARDWARE KIT
INSTALLATION GUIDE Main Components x1 Rail x5 Wall Spacer x2 Anti-jump Block x2 Bent Strap x1 Right Stopper x1 Left Stopper x5 5/16 (8mm x 60mm) Carriage Bolt x5 5/16 (8mm x25mm) Anchor x5 5/16 (8mm x
More informationEntrance Cabinet Plans
Entrance Cabinet Plans www.andrewharriswoodwork.com Page 1 of 19 Introduction I have tried to ensure all steps are covered in these plans but if you find any errors in the plans or have a question then
More informationCongratulations on your purchase of the Divided Light Door Set. This set will help you create beautiful cabinet doors with true divided light panels.
Divided Light Door Set User Instructions Congratulations on your purchase of the Divided Light Door Set. This set will help you create beautiful cabinet doors with true divided light panels. Following
More informationDIY Outdoor Console Table Addicted2DIY.com
DIY Outdoor Console Table Addicted2DIY.com *Before beginning this project, please read through all of the plans. Always use safety precautions whenever using power tools and follow the manufacturer s suggested
More informationMAGNUM BOARD INTERIOR INSTALLATION GUIDELINES
TECHNICAL BULLETIN No.: 090509-1405 Subject: Issue Date: September 4, 2009 Issue No.: II MAGNUM BOARD INTERIOR INSTALLATION GUIDELINES 1. CUTTING MAGNUM BOARD You can easily cut Magnum Board with carbide
More informationKitchen Step Stool. Premium Plan. In this plan you ll find: America s leading woodworking authority
America s leading woodworking authority Premium Plan In this plan you ll find: Step-by-step construction instruction. A complete bill of materials. Construction drawings and related photos. Tips to help
More informationCloset System Installation Manual
Closet System Manual Thank you For choosing our Custom Closet Collection to fit all your needs Closets come fully assembled to make your project an enjoyable and satisfying experience. With quality Custom
More informationPROJECT PLANS EXPANDABLE CRAFT CENTER
R PROJECT PLANS EXPANDABLE CRAFT CENTER Whether you re working on craft projects, sewing, or pursuing another hobby, this craft center offers a great place to work. It features a large work surface that
More informationMODERN BED FRAME ROCKLER BUILD IT WITH BUILD SIMPLIFY CUSTOMIZE. Plan Value $14.99
BUILD Stock # Item 63446 Baltic Birch Plywood /2" x 24" x 30" (2 qty) Stick veneer - Maple 24" x 96" 3/8" Dowels - Birch Bed Connector Hardware I-Semble Platform Bed Frame - Queen 3/8" Beadlock Basic Starter
More informationPatrol Box Plans by David J. Yarusso Troop 609
Patrol Box Plans by David J. Yarusso Troop 609 Materials List: 1. One 4 x8 sheet of ½ thick cabinet grade (birch or oak) or AC plywood. If using AC grade, use the A grade surface on the outside for a clean
More informationHow to Mitre Mouldings
How to Mitre Mouldings About Window and Door Mouldings Mitre cuts are a basic operation in most moulding installation. Mitre cuts are typically 45 degree angles, however many installations require minor
More informationCode Description Qty. Material Dimensions A Long Inner 4 2 x 4 pine 34-1/2 long
B utler s Chest Because it s designed to suit a variety of purposes, this butler s chest is a piece of furniture that absolutely anyone can appreciate. Used by itself, it can serve as an end table or can
More informationx2 1/4 (6mm) Floor Anchor
Main Components x1 Rail x5 Wall Spacer x2 Anti-jump Block x2 Bent Strap x1 Right Stopper x1 Left Stopper x5 5/16 (8mm x 60mm) Carriage Bolt x5 5/16 (8mm x25mm) Anchor x5 5/16 (8mm x 90mm) Wall Screw x2
More informationThank you for purchasing these easel plans. I think you will find this to be a fun, easy to build project that will serve you for years to come.
Construction Plans for The Basic Wooden Easel Updated August, 2002 Thank you for purchasing these easel plans. I think you will find this to be a fun, easy to build project that will serve you for years
More informationrmoire Materials Hardware
A rmoire No house ever has enough storage space, and I built this armoire to satisfy a couple of needs. Inside the armoire is a shelf large enough for the television. Under the shelf are six drawers that
More informationArched. Building an. Passageway. Although my company specializes in high-end jobs
Building an Arched Passageway All photos by Brian Striegler This straightforward approach combines basic shop methods with simple site joinery to create an elegant frame-and-panel archway by Gary Striegler
More informationTripanel Marine Technical Bulletin
Tripanel Marine Technical Bulletin Figure 1 Cabinet joints can be accomplished by four methods: a) rabbet one panel to the proper thickness of joining panel and epoxy joint b) dado to thickness of joining
More informationKreg Tool Co. All Rights Reserved.
Version 1 p. 1 Materials: Lumber: Qty: Board 2 2x2s 3 ft. long 2 1x2s 8 ft. long 2 1x3s 8 ft. long 6 1x6s 10 ft. long INSTRUCTIONS: Supplies: 1 1 / 4" Kreg Screws (coarse thread for softwoods, fine thread
More informationBuild It: The Most Amazing Cooler Bench Ever
Build It: The Most Amazing Cooler Bench Ever wooditsreal.com/2017/04/28/build-it-cooler-bench-free-plans/ A bench. A cooler. Put them together and what do you get? The most amazing Cooler Bench you ve
More informationDIY Farmhouse Cabinet
DIY Farmhouse Cabinet Addicted2DIY.com *Before beginning this project, please read through all of the plans as well as the blog post associated with this project. Always use safety precautions whenever
More informationPROJECT PLAN OUTFEED TABLE
BUILD IT WITH ROCKLER PROJECT PLAN OUTFEED TABLE BUILD Stock # Item 00 ' Universal T-Track () 0 T-Track Intersection Kit 70 JIG IT Universal Drawer Slide Jig 0 " Drawer Slides () 77 Auto-Adjust Jig Clamp
More informationEmpire Dresser Plans
1 Empire Dresser Plans Materials 1 sheet 3/4" plywood (cabinet grade 4' x 8') 1 sheet 5 mm (3/16") underlayment plywood 4'x 8', buy another 1/2 sheet if you want to put a back on the dresser. 1-2" x 4"
More informationProficiency Review Sheet
Youth Performing Arts School Department of Design and Production Instructor: Eric Allgeier, Scenic Designer Stagecraft Class Proficiency Review Sheet Know all of the following terms and be able to identify
More informationWhy are we giving this guidebook as a FREE download?
Construction Guide Queen, Double & Twin Vertical 1 Note: This guide covers the construction steps for all 3 sizes of the vertical wall mount Easy DIY Murphy beds, Queen, Double and Twin. The construction
More informationROUTER BITS. Rabbeting Bits. Rabbeting Bits with Bearing Set Comes with interchangeable bearings to cut rabbets of different depths.
32-098 ROUTER BITS 42 32-504 Rabbeting Bits Produces super smooth cuts on both surfaces of the rabbet. Can be used for joining boards and for letting in back panels. Steel pilots can be removed from bits
More informationDIY Wine Storage Cabinet
DIY Wine Storage Cabinet ADDICTED2DIY.COM *Before beginning this project, please read through all of the plans and the blog post. When building this project, be sure to measure your wood and cut to fit.
More informationMaterials. Special Tools and Techniques Chisel Long pipe clamps Miters Router with 1/2" rabbet cutter Rabbets Dadoes. Hardware
D esk Our executive desk was built with specific needs in mind. We wanted a large desktop, large drawers, and a cubbyhole to house a rollaway hanging file cabinet. We are thrilled with our finished project.
More informationCollegeBedLofts.com Plans for: Loft Bed - Bunk Bed - High Rise Platform Bed
CollegeBedLofts.com Plans for: Loft Bed - Bunk Bed - High Rise Platform Bed High Rise Platform Bed Page 1 of 14 Thank you for ordering our Plans. If you decide at a later date to purchase some of the individual
More informationDESIGN TO BUILD = BUILD TO DESIGN
DESIGN TO BUILD = BUILD TO DESIGN The following represents five days of work from demolition through layout of new flooring and wall frame and cabinetry Paul C. King, RA Associate Professor Department
More informationAgricultural Mechanics and Technology Power Tool Safety Rules
Agricultural Mechanics and Technology Power Tool Safety Rules Name: BAND SAW Use: Cutting curves, circles and irregular shapes. 1. Use clean SHARP blades. 2. The teeth should always point DOWN. 3. Adjust
More information129 KITCHEN BASE CABINET 480
129 KITCHEN BASE CABINET 480 There are two sorts of kitchen cabinets: base cabinets, which sit on the floor, and wall cabinets. Base cabinets provide both storage space and work surfaces. They often house
More informationThe Ultimate Storage Cart Tutorial
The Ultimate Storage Cart Tutorial TOOLS Table saw (or circular saw and straight edge) (alternatively, a good hardware store could make these cuts for you) Router with 1/2 bit Straight edge Clamps Screwdriver
More informationMedia Center Woodworking Plans Our Home from Scratch
Media Center Woodworking Plans by Our Home from Scratch Our Home from Scratch LLC Page 1 Disclaimer Our Home from Scratch LLC and its legal owners cannot be held responsible for any loss, damage, injury
More informationpholstered Vanity Seat
U pholstered Vanity Seat For years I sat on an extremely uncomfortable chair to apply my makeup. I finally replaced it with this sturdy seat that is both attractive and comfortable. This finished size
More informationSafety First! Review the Safety Checklist before performing tasks in this chapter.
Chapter 17. Cabinets 17.1 LAYING OUT KITCHEN CABINET UPPER UNITS 17.2 INSTALLING KITCHEN CABINET SUPPORT STRIPS 17.3 INSTALLING KITCHEN CABINET UPPER UNITS 17.4 INSTALLING RANGE HOOD 17.5 INSTALLING KITCHEN
More informationSection 8. Curved units. Curved units
Section 8 Curved units Curved units Curved corner post... page 94 Curved base cabinet... page 95 Curved wall cabinet... page 96 Curved deep wall cabinet... page 97 Curved plinth - Joining... page 99 www.howdens.com
More informationPROJECT PLAN TOOL CHEST
BUILD IT WITH ROCKLER PROJECT PLAN TOOL CHEST FEATURING ROCKLER S BUILD QUESTIONS? Go to www.rockler.com or call 800-279-4441 Stock # Item 63420 1/4" x 24" x 30" Baltic Birch Plywood 63446 1/2" x 24" x
More informationThis indicates a diagram detailing the dimensions of a project part and/or the placement for pocket holes, screws, nails, etc.
S i m p le Woodworking: What You'll Need v lumber 2-1 x 12 x 6 hardware/supplies (availability will vary) 1 1/4" pocket hole screws #18 x 1 1/2 brads or pocket hole plugs 12-inch continuous hinge magnetic
More informationCedar 2-Drawer Desktop Storage Cube
Cedar 2-Drawer Desktop Storage Cube 5 ½ Dimensions 5 ½ 5 ½ 2 2 1 7/8 4 ¼ 4 ½ Author s Notes: Build a Cedar 2-Drawer Desktop Storage Cube from just 1 cedar fence picket. No angles, special cuts or rips
More informationULTIMATE ROUTER TABLE PLANS. By Dan Phalen
ULTIMATE ROUTER TABLE PLANS By Dan Phalen January 2017 Ultimate Router Table Plans. Copyright 2012-2017 by Daniel Phalen. Published by Creston Hall Publishing Company. All rights reserved. No part of this
More informationPROJECT PLANS MULTIPURPOSE WORK CENTER
R PROJECT PLANS MULTIPURPOSE WORK CENTER This handy project can provide the work space you need anywhere in your home. Whether you need that work space in the shop, the garage, the basement, or in a laundry
More informationRobert Bosch GmbH. Wall organiser
Wall organiser The organisational talent Wall organiser Say goodbye to messiness! The wall organiser is the ideal place to store everything that tends to lie around. 1 Introduction Wardrobes, drawers and
More informationMaking Pocket-Hole Joints
Tips and Techniques 8 SAFETY FIRST Making Pocket-Hole Joints Before doing this activity, make sure you understand how to use all of the tools and materials safely. Adding pocket-hole screws to strengthen
More informationWALL MOUNTED FLOATING WOODEN CABINET
WALL MOUNTED FLOATING WOODEN CABINET How to make and install a floating wall-mounted Shaker-style wooden box for your DVD player and set top box for your wall-mounted flat screen TV What you'll need: Dremel
More informationKitchen Upper Cabinet: Double Doors Cabinets from Scratch
Kitchen Upper Cabinet: Double Doors by Cabinets from Scratch Our Home from Scratch LLC Page 1 Disclaimer Our Home from Scratch LLC and its legal owners cannot be held responsible for any loss, damage,
More informationCowper From Steve Wolverton on the T&TTT forum, Feb 2005 For Reference Only Do not use to build a trailer. Check on Teardrop and Tiny Travel Trailers
Cowper From Steve Wolverton on the T&TTT forum, Feb 2005 For Reference Only Do not use to build a trailer. Check on Teardrop and Tiny Travel Trailers for up to date building information; http://www.mikenchell.com/forums
More informationKitchen Upper Cabinet: Single Door Cabinets from Scratch
Kitchen Upper Cabinet: Single Door by Cabinets from Scratch Our Home from Scratch LLC Page 1 Disclaimer Our Home from Scratch LLC and its legal owners cannot be held responsible for any loss, damage, disappointment,
More informationmake something original Mobile Workstand Shelf support (2) Caster extension (2) Leveling feet (4) Rigid caster (2)
Mobile Workstand Panel (2) Leg (4) Long frame member (2) Crossmember (6) Shelf (1) Shelf support (2) Caster extension (2) Leveling feet (4) Rigid caster (2) THIS IS NOT THE COMPLETE PLAN: it is merely
More informationDIY Full-Size Captain s Bed with Storage. Addicted2DIY.com
DIY Full-Size Captain s Bed with Storage Addicted2DIY.com Before beginning this project Please read through all of the plans as well as the blog post associated with this project. Always use safety precautions
More informationrmoire This attractive and practical two-door armoire takes up very little floor space in a bedroom but provides lots of storage. Because it is only
A rmoire This attractive and practical two-door armoire takes up very little floor space in a bedroom but provides lots of storage. Because it is only a little over 1 foot deep, it s easy to incorporate
More informationPLANS BY KELLEY FARMHOUSE DESIGNS LOFTED DORM ROOM BED
PLANS BY KELLEY FARMHOUSE DESIGNS LOFTED DORM ROOM BED DIMENSIONS: 82" X 70" X 45" DIFFICULTY LEVEL: INTERMEDIATE TOOLS REQUIRED ONE+ Circular Saw ONE+ AirStrike 16GA Finish Nailer ONE+ Impact Driver ONE+
More informationCUSTOM SHUTTERS IN-A-BOX
CUSTOM SHUTTERS IN-A-BOX SHUTTER ASSEMBLE INSTRUCTIONS & INSTALLATION INSTRUCTIONS 1. Inspect the contents of your package. Do not discard the shutter packaging box until you have started painting your
More informationChapter 22 - Cabinets & Vanities
Chapter 22 - Cabinets & Vanities Contents Chapter 22 - Cabinets & Vanities... 22-1 Timing & Prerequisites... 22-2 Cabinets... 22-3 Cabinet Layout... 22-3 Wall Cabinets... 22-4 Assemble the Wall Units...
More informationProject 11010EZ: Gun/Bookcase/Curio Cabinet
Project 11010EZ: Gun/Bookcase/Curio Cabinet No man can be all things to all people, but this cabinet comes as close to fitting multiple uses as any inanimate object can. We ve pictured it as a gun cabinet
More informationContents. Introduction Chapter One... 6 Tools and materials. Chapter Two Simple tables. Chapter Three L-girder benchwork
Contents Introduction....................... 4 Chapter One....................... 6 Tools and materials Chapter Two...................... 8 Simple tables Chapter Three..................... 32 L-girder
More informationWhile creating a two-wall
Ready-To-Assemble Cabinets Outfit your shop in a weekend or less. By Gary Lombard with Jim Harrold 32 woodcraftmagazine.com Aug/Sept 2013 While creating a two-wall or larger shop (or a kitchen, for that
More informationdiy outdoor bar from diyhuntress.com
diy outdoor bar from diyhuntress.com 2 DIMENSIONS & DISCLAIMER: Please double check the overall dimensions for your specific build before starting. Please wear appropriate safety gear when operating power
More informationImportant Note: Why this guidebook is FREE?
Easy DIY Murphy Bed Construction Guide 1 Important Note: This guide is a FREE SAMPLE of our Complete Construction Guidebook. With the help of this guide you will get familiar with the construction steps
More informationOffice Towers 83 ¼ 35 ½ 18 ¼
Copyright 2015 Shanty-2-Chic.com T Office Towers his towering hutch will be admired for years to come. Inspired by rustic, high end furniture found in boutique showrooms it will impress all who see it...especially
More informationSafety First! Review the Safety Checklist before performing tasks in this chapter.
Chapter 17. Cabinets 17.1 LAYING OUT KITCHEN CABINET UPPER UNITS 17.2 INSTALLING KITCHEN CABINET SUPPORT STRIPS 17.3 INSTALLING KITCHEN CABINET UPPER UNITS 17.4 INSTALLING RANGE HOOD 17.5 INSTALLING KITCHEN
More informationBEN'S COUNTRY WOODSHOP SMALL MISSION TABLE Version 2
BEN'S COUNTRY WOODSHOP SMALL MISSION TABLE Version 2 Cutting & Drilling Cut 2 top rails out of 1 x 3s. Each will be 8 1/2 long. Drill 1 pocket hole on the inside bottom center. This will connect the center
More informationDisplay Case (for J&S)
Display Case (for J&S) This is constructed of maple plywood with solid maple (soft maple) edge banding. It was made to fit between a door and a kitchen cabinet, and has an elegant circular taper between
More informationBuild Instructions for Towers of Doom
Build Instructions for Towers of Doom 1. Measure and cut 4 x 8 sheet of plywood in half (or ask Home Depot to do it!). You will use one 4 x 4 sheet for the course base. 2. Attach a support frame to the
More informationBaby Grande with Crank, Housing, and Side Rails Installation Instructions
Baby Grande with Crank, Housing, and Side Rails Installation Instructions Tools Needed Hardware Provided (per shade) Hardware Needed Drill 3/8 Metal Drill Bit ¼ Masonry Drill Bit Measuring Tape Pencil
More informationJeff Branch WOODWORKING YOU CAN BUILD A. By adding subtle design elements, a traditional furniture style becomes decidedly modern.
Jeff Branch WOODWORKING YOU CAN BUILD A By adding subtle design elements, a traditional furniture style becomes decidedly modern. Jeff Branch WOODWORKING Publisher: Jeff Branch Editor: Jeff Branch Art
More informationInstallation Instructions. Conventional Wainscot Wall Padding Panels MODEL # RWC25321 RWC26321 RWC253X1 RWC263X1 RWC25321 RWC25XXX RWC26XXX
Conventional Wainscot Wall Padding Panels MODEL # RWC25321 RWC26321 RWC253X1 RWC263X1 RWC25321 RWC25XXX RWC26XXX Installation Instructions FOR CONVENTIONAL PANELS 07/05 SPT050026 CUSTOMIZED PADS We offer
More informationInstallation Fence Guide Kodiak Iron. Exceptional Fencing Extraodinary Customer Service
Installation Fence Guide Kodiak Iron Exceptional Fencing Extraodinary Customer Service Kodiak Fence System Installation Guide Thank you for the purchasing the Kodiak Fence System. Fence installation is
More information1 ¼-inch Pocket Screws Brad Nailer or Hammer 1 ¼-inch Brad Nails Clamps
MATERIALS: TOOLS: (4) 2 x 6 x 8 Ft. Boards Tape Measure (2) 2 x 4 x 8 Ft. Boards Carpenter s Square (7) 1 x 4 x 8 Ft. Boards Pencil (2) 1 x 3 x 8 Ft. Boards Drill (1) Half Sheet of ¾-inch Thick Plywood
More informationTriangle Triumph Game Elements. Table of Contents
CAppendix JR. Triangle Triumph Game Elements Table of Contents Appendix C Triangle Triumph Playing Field...2 C.1 Description...2 C.2 Bill of Materials...2 C.3 Rack Bases...3 C.4 Rack System...4 C.5 Central
More informationPLANS BY TOM BURY JOB BUDDY TOTAL DIMENSIONS: 44 X 18 X 14 DIFFICULTY LEVEL: INTERMEDIATE
JOB BUDDY TOTAL DIMENSIONS: 44 X 18 X 14 DIFFICULTY LEVEL: INTERMEDIATE MATERIAL LIST: (5) 1 x4 x8 (2) 1 x4 x6 (1) 48 x48 3/4 plywood (1) 24 x24 metal mesh (1) 2 x 8 angle iron (1) 3 x 24 flat iron bar
More informationCorner Entertainment Center Plans
Table of Contents Introduction... 3 Let s discuss the tools needed... 3 Let s discuss the materials needed... 4 Let s build it... 4 Attaching the 2x2's... 7 Determine the shelf spacing... 9 Scribing the
More informationMATERIALS: TOOLS: CUT LIST:
MATERIALS: TOOLS: (2) 2x2x8 Ft. Boards Tape Measure (2) 1x4x8 Ft. Boards Pencil (4) 1x2x8 Ft. Boards Carpenter s Square (1) 4x4 Ft. Sheet of ¾-Inch Plywood Drill with 5/16-inch Drill Bit (1) 1 ½-inch Thick
More informationPLANS BY TOM BURY MURPHY WORKTABLE TOTAL DIMENSIONS: FOLDED UP 30 X 48 X 0 FOLDED DOWN 30 X 58 X 84
MURPHY WORKTABLE TOTAL DIMENSIONS: FOLDED UP 30 X 48 X 0 FOLDED DOWN 30 X 58 X 84 MATERIALS LIST: (2) 2 x8 x8 (3) 2 x4 x8 (1) 1 x2 x8 (1) 48 x96 3/4 plywood (2) 1-1/2 x30 continuous hinge (1) Left-side
More informationCopyright 1998 KDE Technologies
Modular Computer Corner Desk Unit Copyright 1998 KDE Technologies http://members.tripod.com/~kdetech/ 1. Introduction 2. Plans Sheet one - Isometric Sheet two - Top Detail / Corner Unit Sheet three - Leg
More informationBuilding an Elevated Garden Bed & Hydroponic Table
Building an Elevated Garden Bed & Hydroponic Table Materials: Lumber (2x4, 2x6, 1x4), Exterior Grade Wood Screws (2 1/2 & 1 5/8 ) and Hardware Cloth (enough to cover a 24 x48 area) Tools: Cordless Drill
More informationGrade 11 Woods Lift Lid Coffee Table. Based on Under the big Top from Popular Mechanics Website
Grade 11 Woods Lift Lid Coffee Table Based on Under the big Top from Popular Mechanics Website TABLE TOP 1. Select enough lumber to construct a top that is between 22 ½ and 24 wide after jointing. Ensure
More informationPlans. Easy-to-Build Full-size Deluxe Murphy Bed Plan. For more plans, tools and hardware visit rockler.com
Easy-to-Build Full-size Deluxe Murphy Bed Plan Build a full-size Deluxe Murphy Bed complete with decorative molding and matching side cabinets! Plans For more plans, tools and hardware visit rockler.com
More informationChest of Drawers Plans
Chest of Drawers Plans www.andrewharriswoodwork.com Page 1 of 15 Introduction This plan makes a chest of drawers that is 50 inches at the widest point, 19 inches deep and 40.75 inches high. I have tried
More informationCABINET INSTALLATION INSTRUCTIONS
CABINET INSTALLATION INSTRUCTIONS Please read these instructions through completely before beginning the installation. Thank you for choosing Plato Personalized Custom Cabinetry for your home. Your Plato
More informationHOW TO INSTALL ELITE PANELED WAINSCOTING Using X-Rails with Either Raised, Flat or Beaded Panels
HOW TO INSTALL ELITE PANELED WAINSCOTING Using X-Rails with Either Raised, Flat or Beaded Panels 1. First, remove the cover plates from all electrical outlets. All baseboards should also be removed; the
More informationClassic Kitchen Island
America s leading woodworking authority Step by Step construction instruction. A complete bill of materials. Classic Kitchen Island Exploded view and elevation drawings. How-to photos with instructive
More informationBUILDING A STORM DOOR
BUILDING A STORM DOOR BY NEAL BARRETT Illustrations by George Retseck If you're in the market for a storm door, you probably know that there are many styles and models available. However, most of them
More informationProject 11355EZ: Wall Cabinet with Louvered Doors and Shelf
Project 11355EZ: Wall Cabinet with Louvered Doors and Shelf This Early American style cabinet will look good in any room, although it seems particularly well suited for the kitchen or bathroom. To make
More informationTimberflex & Flexboard Technical Guide
Timberflex & Flexboard Technical Guide A bendable substrate material that can be formed first and laminated last Patent #5,618,601; #5,232,762; #5,824,382 Doors Larger radius and small doors are easily
More informationCastle Bed. Page 1 of 24
Castle Bed www.andrewharriswoodwork.com Page 1 of 24 Introduction This plan makes a twin bed that is 91 inches long and 60 inches wide. I have tried to ensure all steps are covered in these plans but if
More informationU. M. ARMY Texas Conference. Wheel Chair Ramp Manual
U. M. ARMY Texas Conference Wheel Chair Ramp Manual June 2014 U. M. ARMY Texas Conference Building & Repair Tips Wheelchair Ramps Complete a site survey to determine the design and layout of the ramp.
More informationWooden Christmas Tree
Wooden Christmas Tree Created by DIY hacker, woodworker and teacher, Kerryn Carter of Toolschool, take your Christmas tree to a whole new level, with this wooden Christmas Tree project. PROJECT INFORMATION
More informationThis indicates a diagram detailing the dimensions of a project part and/or the placement for pocket holes, screws, nails, etc.
S i m p le Woodworking: Bath Side Table What You'll Need v lumber 4-1- x 36-inch square dowels 1-1 x8x8 1-3/4-inch x 2- x 4-foot sheet of plywood hardware/supplies 1 1/4" pocket hole screws #18 x 1 1/2
More informationLARGE PLYWOOD CUTTING GUIDE
Copyright 2015 Shanty-2-Chic.com Workbench I f you are tight on space but large on ideas this bench is just what you need. Sturdy and mobile this bench has an ingenious fold out wing that gives you over
More informationMyOutdoorPlans.com. By Julian King [2X4 GARDEN BENCH]
MyOutdoorPlans.com By Julian King [2X4 GARDEN BENCH] CUT LIST A 2 pieces of 2 4 lumber 24 long, 2 pieces 32 1/2 long LEGS B 2 pieces of 2 4 lumber 45 long, 2 pieces 15 1/2 long, 1 piece 12 1/2 long SEAT
More informationDisplay/Accessory Furniture
1 Multimedia Display End-of-Range, 60-013-S00 End-of-range displayer has five 59 1 /2" 19 3 /8" 16" 163 Sloped Shelving Book Displayer sloping shelf spaces for displaying books spine out at an angle for
More informationPlace your board facing inward this time and set the stop block to receive the freshly cut miter. Again, cut the right end. FENCE
Stretcher Assembly - Method #1 For stretchers under 3 feet, no table saw 1. Select straight 1x3 and quarter round, equal lengths (unless you need cross braces - then extra 1x3 must be purchased): pine,
More information