Build a Rolling Tool Tote
|
|
- Tobias Hudson
- 6 years ago
- Views:
Transcription
1 The rolling tool tote design calls for readily available materials: a cheap hand truck (it could be an axle and two wheels), 3/4 and 1/2 thick plywood, 1/4 thick MDF (you could use plywood or hardboard) and common hardware. The dimensions of the tote shown are 36 high x 16 wide x 12 deep, but you can adapt those measurements according to your needs, storage space and strength. As you will see, the final result is quite versatile. Getting Started: The Casing Ensure your saw blade is set to 90 and rip two 12 strips from a sheet of 3/4 plywood (MDO plywood shown). From those strips, cut two 12 x35 long sides and a 12 x16 long top and bottom. Set aside the remaining material to use for the front doors. Install a dado blade set in your table saw and a sacrificial fence to protect the rip fence. Set the width according to the thickness of your 3/4 plywood and the depth to 1/2. Mill a rabbet at each end of the top and bottom pieces. Move the rip fence closer to set the width of the dado to 1/2 (the thickness of the plywood to be used for the back panel). Mill the required rabbets on the back of both sides and the back of the top and bottom. Clamp the four sides together, ensuring all joints fit tightly. Measure the distance between the back rabbets and cut the 1/2 thick plywood to size for the back panel. When done, check the diagonals to ensure the casing is square. Put aside the back panel at this time. 1/6
2 Set your dado blade to 1/4 wide and 3/8 deep and measure the inside walls of the sides from top to bottom and rabbet to rabbet. Divide by the number of drawers you want. For versatility, all of the drawers should be identical so that you can slide any one of them into any of the locations. All of my drawers are 4 tall and fit into all of the 4-1/16 high locations. When ready, mill all dadoes and use glue and nails to assemble the casing, ensuring that it s square. Building the Inner Parts The dadoes that you mill in the sides may cause the panels to bow, as mine did. Size and cut a 1/4 plywood fixed shelf to width to keep the sides parallel and reinforce the casing. Glue, nail and clamp this shelf and let it dry. Meanwhile, measure and cut 1/4 MDF (or other material) drawer bottoms that will easily slide in the side dadoes. They should be about 1/16 narrower than the distance from dado bottom to dado bottom. Rip 1/2 plywood strips about 1/16 narrower than the vertical distance between the adjacent edges of the dadoes. From those strips, cut drawer fronts and backs 1/8 narrower than the distance between the insides of the casing sides. Use the table saw to mill a 1/4 deep rabbet at each end for the drawer sides. To get the exact length for the drawer sides, slip one back into position in the casing and measure from the rabbet bottom to the front of the casing. Subtract the thickness of the front lip. 2/6
3 To add pulls to your drawer fronts, choose the best face of your 1/2 plywood stock. Clamp two drawer fronts side by side and use the drill press to bore a center hole using a 1-1/2 dia. Forstner bit or hole saw. Soften the edges of the pulls using a 1/8 round-over bit. Sand smooth. I came up with a simple, effective set-up for assembling the many drawers. Clamp two square brackets to the workbench to hold the drawer parts while you glue. Nail from above, the sides and into the front and back rabbets. After assembling the four sides of a drawer, immediately nail the bottom onto it before the glue sets, leaving an equal lip on each side. Stack the drawers one after the other and add a weight to ensure a good bond. (I filled a 4l plastic container with sand to make an 18 lb weight.) After the glue is set, your drawers should slide easily in each slot of the casing and stay put without tipping over when open. 3/6
4 Step Further If you plan to put hardware and small or sharp tools in the drawers, here are some suggestions for storing them. Using double-sided tape, secure tin cans (I used sardines cans) on the bottom of a drawer and nail a thin cleat on each side to add a second removable layer. Another option is to cut and fit two plastic utensil trays that you can get at any discount store. 4/7
5 Cut the doors to height and add 3/8 to the width of one door if you want them to overlap, as shown. By doing so, only one latch is required. Cut the rabbet and secure one door with two hinges. Lean the second door over to evaluate the width of the second rabbet. You are looking to leave a 1/16 gap on the front of the door. Hinge the second door and add a pull to each one. Join the Casing to the Hand Truck You can permanently attach the casing to the hand truck with nuts and bolts, but I find a better way is to use the French cleat system. At the table saw, rip two 16 long x 5 wide 3/4 plywood strips in half lengthwise at a 45 bevel. Drill the hand truck and bolt (flat head) two freshly ripped French cleats, bevel side up, close to both ends of the hand truck. Temporarily clamp the casing to the hand truck and spread glue on the two remaining cleats. Slip them into position, bevel side down, so that they match the bevel of the already installed cleats. Secure them to the casing with screws through the back into each side. Immediately unclamp the casing and remove any glue squeeze out. Drop the casing on its back and under the box screw a 5/8 spacer along the front bottom edge to compensate for the lower metal shelf of the hand truck. Add more screws in the cleats from the inside of the casing. 5/7
6 When you re ready to work, hook the casing onto the hand truck, hang some clamps and an electric cord (or garden hose) on the hand-truck handle, remove or add drawers and tools as needed, and lock the doors. Enjoy your new freedom! 6/7
7 Additional Step For winter storage, rip another French cleat and screw it to a wall (on the studs, of course). When you re not using your tool tote outside, hang it on the wall and use it as a typical tool cabinet. Happy woodworking, happy gardening and happy travelling! Text and photos by Serge Duclos Serge Duclos started woodworking 40 years ago after purchasing a house. He soon found it was a way to relax from the stress related to his job as a human resources professional. Since retiring in 2004, Serge continues to enjoy his pastime and to update his bilingual woodworking blog wordpress.com with his projects, as well as his tips and techniques. 7/7
Shop-Made Miter Clamps
*Editor s note: In the photos showing the table saw, the blade guard has been removed for clarity. I try to be as self-sufficient as possible, so I like to manufacture my own tools whenever I can. I designed
More informationPROJECT PLAN OUTFEED TABLE
BUILD IT WITH ROCKLER PROJECT PLAN OUTFEED TABLE BUILD Stock # Item 00 ' Universal T-Track () 0 T-Track Intersection Kit 70 JIG IT Universal Drawer Slide Jig 0 " Drawer Slides () 77 Auto-Adjust Jig Clamp
More informationBuilding Instructions
Building Instructions Tools Required Tape measure Straight edge Pencil/pen Jigsaw Table Saw Circular Saw Electric drill 1 Hole saw bit Saw horses/table Protractor Staple gun Caulk gun Paint brush Wrenches
More informationClassic Mitered Jewelry Box
America s leading woodworking authority Premium Plan In this plan you ll find: Step-by-step construction instruction. A complete bill of materials. Construction drawings and related photos. Tips to help
More informationHow to Build a Recessed Medicine Cabinet
How to Build a Recessed Medicine Cabinet See post for install info http://www.hertoolbelt.com/recessed-medicine-cabinet/ Materials 6 Inset Cabinet Door Hinges 3 Latches 1 sheet Beadboard or 1/4 plywood
More informationProject 17884EZ: Shaker End Table
Project 17884EZ: Shaker End Table With its clean, simple lines, this piece is unmistakably Shaker style. Ours is made from cherry, a wood commonly used by Shaker craftsman, but we ve also seen this piece
More informationEntrance Cabinet Plans
Entrance Cabinet Plans www.andrewharriswoodwork.com Page 1 of 19 Introduction I have tried to ensure all steps are covered in these plans but if you find any errors in the plans or have a question then
More information10 Easy-to-Build. Plywood Projects
10 Easy-to-Build Plywood Projects Ten shop projects ten sheets of plywood. These rock-solid essentials take just a couple hours to build and will help you make the most of the space in your shop. All content
More informationProject 13586EZ: Writing Desk. Writing Desk Materials List
Project 13586EZ: Writing Desk This writing desk will make a handsome addition to just about any room in the house. The one shown is made of cherry, a logical choice for a piece like this, but mahogany
More informationULTIMATE ROUTER TABLE PLANS. By Dan Phalen
ULTIMATE ROUTER TABLE PLANS By Dan Phalen January 2017 Ultimate Router Table Plans. Copyright 2012-2017 by Daniel Phalen. Published by Creston Hall Publishing Company. All rights reserved. No part of this
More informationModern Farmhouse Printer Cabinet. Addicted2DIY.com
Modern Farmhouse Printer Cabinet Addicted2DIY.com Before beginning this project please read through all of the plans as well as the blog post associated with this project. Always use safety precautions
More informationBathroom Storage Unit. Wilkerdos.com
Bathroom Storage Unit Wilkerdos.com Copyright 2015 Material List Quantity Item Notes 1 4 x 8 x 3/4 plywood Construction grade 1 2 x 4 x 1/2 plywood Construction grade 11" 7-1/2" Page 1 Some 1 1/4" brad
More informationwoodworkersjournal.com MATERIAL LIST
MATERIAL LIST T x W x L 1 Legs (2) 1 1 2" x 3 1 2" x 36 7 16" 2 End Uprights (2) 1 1 2" x 3 1 2" x 32 1 2" 3 Stringers (4) 1 1 2" x 3 1 2" x 42" 4 Top Cladding, Long (2) 3/4" x 7 1 4" x 65 3 4" 5 Side
More informationAbout.com :
http://woodworking.about.com/gi/dynamic/offsite.htm?sit...//www.popularwoodworking.com/features/fea.asp%3fid=1088 (1 of 8)1/28/2004 12:05:01 AM Modern Storage Tower The last thing I want to do when starting
More informationJigsaw Puzzle Tray. Premium Plan. In this plan you ll find: America s leading woodworking authority
America s leading woodworking authority Premium Plan In this plan you ll find: Step-by-step construction instruction. A complete bill of materials. Construction drawings and related photos. Tips to help
More informationBuild a Stout Workbench
Build a Stout Workbench Tail vise is at the heart of this versatile bench by chris gochnour I ve done a fair amount of handplaning during my 32 years as a professional furniture maker, and I ve found that
More informationChest of Drawers Plans
Chest of Drawers Plans www.andrewharriswoodwork.com Page 1 of 15 Introduction This plan makes a chest of drawers that is 50 inches at the widest point, 19 inches deep and 40.75 inches high. I have tried
More informationThe WoodWorker s Edge
The WoodWorker s Edge Draw-leaf Game Table 1. 2. Layout the area for the tenons. The tenons are 3/8 thick x 4-1/2 long x 1-1/4 deep and offset to the inside. Create the tenons using the step method to
More informationPivot-Door Downdraft Cabinet Plans
Pivot-Door Downdraft Cabinet Plans Finished Cabinet Closed Open Exploded View Introduction This simple downdraft-style dust collection cabinet is a great way to keep your shop cleaner and keep your router
More informationHinge Mortising Jig. One of the make it or break it parts of building a. 6 ShopNotes No. 74
Hinge Mortising Jig A Mortise for a Hinge. Quick, clean, and accurate that s the only way to describe the mortise you get with a trim router and this hinge mortising jig. One of the make it or break it
More informationJeff Branch WOODWORKING YOU CAN BUILD A. By adding subtle design elements, a traditional furniture style becomes decidedly modern.
Jeff Branch WOODWORKING YOU CAN BUILD A By adding subtle design elements, a traditional furniture style becomes decidedly modern. Jeff Branch WOODWORKING Publisher: Jeff Branch Editor: Jeff Branch Art
More informationPROJECT PLAN TOOL CHEST
BUILD IT WITH ROCKLER PROJECT PLAN TOOL CHEST FEATURING ROCKLER S BUILD QUESTIONS? Go to www.rockler.com or call 800-279-4441 Stock # Item 63420 1/4" x 24" x 30" Baltic Birch Plywood 63446 1/2" x 24" x
More informationAmerica s leading woodworking authority To download these plans, you will need Adobe Reader installed on your computer. If you want to get a free copy, visit: http://adobe.com/ reader. Having trouble downloading
More informationKentucky 4H Wood Science Plans Notebook. Plans Level 3
Kentucky 4H Wood Science Plans Notebook Plans Level 3 MATERIALS: 2 pieces wood 3/4 x 10 x 4 1 piece wood 3/4 x 12 x 4 2 pieces wood 3/4 x 3 x 2 5 1/2" 2 pieces wood 3/4 x 3 x 1 8 1 piece wood 2 x 4 x
More informationNext-Generation Router Table
Next-Generation Router Table Make more accurate cuts with a flat, solid-surface top. by John English 2 AmericanWoodworker.com 9 Key Features 1. Hinged Top. Bit changes are much easier. 2. Pivot Control.
More informationBUILDING A STORM DOOR
BUILDING A STORM DOOR BY NEAL BARRETT Illustrations by George Retseck If you're in the market for a storm door, you probably know that there are many styles and models available. However, most of them
More informationPULLOUT SHELF ROCKLER BUILD IT WITH BUILD CUSTOMIZE
BUILD Stock Item 12229 Drawer s, 2 1 2" x 48" 63420 Baltic Birch Ply, 1/4" x 24" x 30" 38742 Maple, 3/4" x 3" x 24" 45953 100# Zinc Over-Travel Drawer Slides - Centerline 757-20" 30254 #8 x 1 1 4" Square
More informationJewelry Cabinet. Materials: 5/8" brad nails 5-1" x 3" x 8' boards (or if not 2 1/2" wide. 1-4' x 8' sheet - 3/4" plywood. wood glue get 1x4's)
1 Jewelry Cabinet Materials: 1-4' x 8' sheet - 3/4" plywood 5/8" brad nails 5-1" x 3" x 8' boards (or if not 2 1/2" wide wood glue get 1x4's) sand paper 1-1" x 6" x 8' board wood filler 1/2 sheet - 3/16"
More informationWhile creating a two-wall
Ready-To-Assemble Cabinets Outfit your shop in a weekend or less. By Gary Lombard with Jim Harrold 32 woodcraftmagazine.com Aug/Sept 2013 While creating a two-wall or larger shop (or a kitchen, for that
More informationRLP Flat Track Hardware sliding door hardware/ barn door track
Page 1 of 9 Installation Suggestions for: RLP Flat Track Hardware sliding door hardware/ barn door track Read these instructions to end before starting installation or ordering hardware. Reclaimed Lumber
More informationMaterials. Special Tools and Techniques Chisel Long pipe clamps Miters Router with 1/2" rabbet cutter Rabbets Dadoes. Hardware
D esk Our executive desk was built with specific needs in mind. We wanted a large desktop, large drawers, and a cubbyhole to house a rollaway hanging file cabinet. We are thrilled with our finished project.
More informationDIY Rustic Dresser Addicted2DIY.com
DIY Rustic Dresser Addicted2DIY.com *Before beginning this project, please read through all of the plans as well as the blog post associated with this project. Always use safety precautions whenever using
More informationPROJECT PLANS MULTIPURPOSE WORK CENTER
R PROJECT PLANS MULTIPURPOSE WORK CENTER This handy project can provide the work space you need anywhere in your home. Whether you need that work space in the shop, the garage, the basement, or in a laundry
More informationThe Q Frame PROJECT. a picture frame with secrets created exclusively for the Router Forum
The Q Frame PROJECT a picture frame with secrets created exclusively for the Router Forum 007 OR RELEASE FPLANS APPROVED The Q Frame: Project Overview LIST OF MATERIALS Frame Sides & Face 3/4 x 5 1/2 x
More informationRouter bit cabinet August Home Publishing Co.
Router bit cabinet 2011 ugust Home Publishing Co. Feature Project Router Bit Cabinet Dovetail keys at the corners reinforce the joints to make a stronger cabinet. Plus, a clear, plastic door panel lets
More informationProject 11355EZ: Wall Cabinet with Louvered Doors and Shelf
Project 11355EZ: Wall Cabinet with Louvered Doors and Shelf This Early American style cabinet will look good in any room, although it seems particularly well suited for the kitchen or bathroom. To make
More informationSINGLE TRACK BYPASS (patent pending) barn door hardware
SINGLE TRACK BYPASS (patent pending) barn door hardware Installation Manual What is included in your kit: Part number Part name Quantity 1 Inner door hanger 2 2 Outer door hanger 2 3 5/16 x 1.5 lag bolts
More informationRouter Table. Construction
Router Table A router table is an invaluable tool. The problem, however, is that ready-built router tables are usually relatively expensive and too narrow for many projects. This router table provides
More informationThis is a solid wood cabinet. The only plywood used is for the back and drawer bottoms.
Sideboard Sideboard Overview: This project requires basic woodworking skills and access to woodworking machines. Woodworking machines have sharp cutting edges and are NOT forgiving. You should be properly
More informationTraditional glass-pane and wood-muntin doors highlight this free-standing piece.
Bookcase Traditional glass-pane and wood-muntin doors highlight this free-standing piece. As the saying goes, there's nothing like good books. But they can present some storage problems--especially if
More informationChest of Drawers Plans
Chest of Drawers Plans www.andrewharriswoodwork.com Page 1 of 12 Introduction This plan makes a chest of drawers from 2 by 4s and 2 by 6s for the top. The cabinet is 22 ½ inches at the widest point, 22
More informationENJOY THIS SELECTION FROM. Woodworking 101. Includes Step-by-Step Instructions for 8 Projects. Woodworking
W ENJOY THIS SELECTION FROM Woodworking 101 Includes Step-by-Step Instructions for 8 Projects Woodworking 101 Aimé Fraser, Matthew Teague, and Joe Hurst-Wajszczuk To purchase your copy of Woodworking 101,
More informationShopsmith Mobile Storage Cabinet.
http://wwwinstructablescom/id/shopsmith-mobile-storage-cabinet/ technology workshop living food play outside Shopsmith Mobile Storage Cabinet by Beave2012 on May 3, 2015 Table of Contents Shopsmith Mobile
More informationARTS AND CRAFTS CHAIR
ARTS AND CRAFTS CHAIR 491 MATERIALS LIST--DINING CHAIR Key No. Size and description (use) A 2 1-3/4 x 1-3/4 x 16-1/4'' oak (front leg) B 2 1-3/4 x 3-3/4 x 40-1/2'' oak (rear leg) C 1 1-3/4 x 3-3/16 x 15''
More informationRouter Table-Mate. Everything you'd want in a router table for just $50.
Router Table-Mate Everything you'd want in a router table for just $50. Commercially made router tables are everywhere these days. Some of them come with more gizmos and gadgets than a 59 Edsel. By the
More informationUltimate Miter Saw Stand
America s leading woodworking authority Ultimate Miter Saw Stand To download these plans, you will need Adobe Reader installed on your computer. If you want to get a free copy, visit: http://adobe.com/reader.
More informationShop Projects. Plans NOW. Each Built from One Sheet of Plywood!
Plans NOW www.plansnow.com 5 Shop Projects Each Built from One Sheet of Plywood! Tool Tote - Sawhorse - Workbench - Wood Bin - Wall Cabinet PLUS: 7 SHOP SECRETS Working with Plywood Dread the thought of
More informationSilverware Chest Plan
Silverware Chest Plan 05L14.01 Introduction 1. Measure the space required for your cutlery before beginning this project to be sure that it will fit in the drawers and top compartment. The best way to
More informationTable to Go. Build a foldable, portable, storable table for four WORKSHOP
WORKSHOP Table to Go Build a foldable, portable, storable table for four by Dan Cary This table is designed to handle the rigors of outdoor use and travel, but it is equally at home indoors. If you ve
More informationA Deluxe Chisel Cabinet
After I finished my wall-mounted tool chest (8 x 21 x 36 ) a few years ago, a wise friend warned me [I]t s one that holds disappointment in its heart. The day will certainly come when there is no more
More informationKentucky 4H Wood Science Plans Notebook. Plans Level 4
Kentucky 4H Wood Science Plans Notebook Plans Level 4 MATERIALS NEEDED: Note: 1" wood may be 3/4" thick and 2" x 2" may be 1 1/2" x 1 1/2" 2 pieces wood 1 x 3 x 17 1 piece wood 1 x 3 x 14 3/4" 2 pieces
More informationLaminate Cabinet Installation Instructions
Laminate Cabinet Installation Instructions www.easygaragestorage.com/installation How To Use These Instructions Thank you for your purchase! Please read each step of this manual thoroughly to ensure proper
More informationPROJECT PLAN TRAVEL CRIBBAGE BOARD
BUILD IT WITH ROCKLER PROJECT PLAN TRAVEL CRIBBAGE BOARD BUILD Stock # Item Stock # Item 59160 Small Cribbage Board Template, 2-Player, Straight Track 90638 3/4" Dia. Straight Router Bit (1/2" shank) 21026
More informationIndustrial Cart. Materials. With High Style Restyle
1 Industrial Cart With High Style Restyle Materials 1 sheet 3/4" plywood 1-1" x 2" x 8' board 2-1" x 3" x 8' board 1-2" x 8" x 10' board 1-2" x 6" x 8' board 3-1/4" x 2 1/2" x 4' poplar hobby boards, or
More informationDOWNLOAD PDF HOW TO BUILD KITCHEN CABINETS, ROOM DIVIDERS, AND CABINET FURNITURE
Chapter 1 : How To Build Kitchen Cabinets Room Dividers Furniture Donald Brann DIY ebay How to Build Kitchen Cabinets, Room Dividers, and Cabinet Furniture [Donald R. Brann] on blog.quintoapp.com *FREE*
More informationPocket Door Kit PD1 / PD2 Installation Instructions. Kit Contents.
Pocket Door Kit PD1 / PD2 Installation Instructions Kit Contents. 1, Create Rough Opening In Stud Wall Construct rough opening ensuring all sides are square and level. Rough opening should be; Height =
More informationDRILL BIT STORAGE August Home Publishing Co.
DRLL BT STORA 2010 August Home Publishing Co. Shop Project Drill Bit Storage ALL PARTS XCPT AR!/2"-THCK HARDWOOD C (3" x 10") a. b. 1 BACK VW HANR SLOT SD VW A (4" x 10" - " Hdbd.) c. COUNTRBOR ORMS POCKT
More informationhanging mirror Two-piece desk set Handmade Gifts Photo: John Tetreault
hanging mirror Two-piece desk set Handmade Gifts 44 FINE woodworking Photo: John Tetreault Flatware carrier Tea light candle holder 4 Tasteful projects made quickly from scraps BY CHRISTIAN BECKSVOORT
More informationThe Universal Table Saw Sled
The Universal Table Saw Sled Do Precision Work Even with Inexpensive Table Saws! Table saw blades always tend to move the wood while the cut is being made. This is why it's so difficult to get accurate
More informationrmoire Materials Hardware
A rmoire No house ever has enough storage space, and I built this armoire to satisfy a couple of needs. Inside the armoire is a shelf large enough for the television. Under the shelf are six drawers that
More informationClassic Kitchen Island
America s leading woodworking authority Step by Step construction instruction. A complete bill of materials. Classic Kitchen Island Exploded view and elevation drawings. How-to photos with instructive
More informationDewalt Organizer Storage Cabinet Plans
Dewalt Organizer Storage Cabinet Plans Version 1.0 How to build a system to perfectly organize you Dewalt storage organizers. With easy to follow step-by-step instructions, you will be able to cut, assemble,
More informationI I. . i1 AD JUSTABLE SHELVES
ADJUSTABLE SHELVES HAD BEEN TRYNG TO WORK out a really simple (read "fast") way to make an elegant wooden version of the old standby, metal standards and brackets. Although have seen many commercial versions
More informationOutdoor Cooler Cart. Outdoor Cooler Cart Construction Instructions
Outdoor Cooler Cart Outdoor Cooler Cart Construction Instructions Make the Legs and Side Panels. Cut the eight long and short leg pieces to length. See Material List on next page.. Apply a bead of glue
More informationAssembly Instructions 10 X 10 Aluminum Roof Support
Assembly Instructions 10 X 10 Aluminum Roof Support Aluminum Roof Support Bolt Package 16-5/16 X 2 ¼ SS Bolt 24-5/16 X 1 SS Bolt 40-5/16 SS Nylon Lock Nuts 16-5/16 SS Flat Washers 28-4 ½ Wood Screws 36-1
More informationMedia Console Table 38"
Copyright 2016 Shanty-2-Chic.com Media Console Table A sleek, modern take on a traditional concept; this console table is as stylish as it is functional and you'll have it done in a weekend. And versatile
More informationDIY Full-Size Captain s Bed with Storage. Addicted2DIY.com
DIY Full-Size Captain s Bed with Storage Addicted2DIY.com Before beginning this project Please read through all of the plans as well as the blog post associated with this project. Always use safety precautions
More informationA Shaker Sewing Stand
America s leading woodworking authority Step by Step construction instruction. A Shaker Sewing Stand A complete bill of materials. Exploded view and elevation drawings. How-to photos with instructive captions.
More informationEmpire Dresser Plans
1 Empire Dresser Plans Materials 1 sheet 3/4" plywood (cabinet grade 4' x 8') 1 sheet 5 mm (3/16") underlayment plywood 4'x 8', buy another 1/2 sheet if you want to put a back on the dresser. 1-2" x 4"
More informationNEXUS SERIES CABINETS
NEXUS SERIES CABINETS STANDARD BASE ASSEMBLY INSTRUCTIONS Also applies to: Galaxy Series, Nexus Series, Ridgeline Series, Statesman Series, and Waterford Series FOR YOUR INFORMATION: These assembly instructions
More informationPopular Woodworking Magazine. Router Fence for a Table Saw. (1 of 7)02/09/
Router Fence for a Table Saw http://www.popularwoodworking.com/features/fea19.html (1 of 7)02/09/2005 11.15.18 Your table saw is a router table and jointer just waiting to happen. Replace one of the saw's
More informationPinewood Derby Display Case
Pinewood Derby Display Case Optional Door Design by Neil Fern - Pack 187 Exterior Dimensions 23 ½ (H) X 10 ½ (W) X 3 ½ (D) Front Back OPTIONAL Door Finished Interior Dimensions 21 7/8 (H) X 9 (W) X 3 (D)
More informationHardware Cabinet. Part 3
Hardware Cabinet Part 3 The vertical dividers are the next task on the cabinet and a bit of a trick to get right. The horizontal dividers are only ½ thick pine spanning the 31 width of the cabinet and
More informationMLCS Instructions for Bowl and Tray Template Kit #9176/#9179
MLCS Instructions for Bowl and Tray Template Kit #9176/#9179 Tools Needed: Router 1-1/2 h.p. Minimum recommended with a 1/2 collet Forstner bit 3/4-2 recommended depending on template used Drill Press
More informationParts List (Continued) 18 each: #8 x 0.625" Truss Head Phillips Screw 20 each: #8 x 1.75" Flat Head Phillips Screw 4 each: #8 x 1.25" Flat Head Philli
EVO Tall Pull-Out Wood Pantry Important Notes Always read the instructions completely and carefully before beginning assembly. Remove and check contents for damage and/or missing parts. Keep the original
More informationInstallation Instructions
by Plato Woodwork Installation Instructions Plato Woodwork, Inc. 200 Third Street SW P.O. Box 98 Plato, MN 55370 www.platowoodwork.com 800.328.5924 SECTION GUIDE GETTING STARTED PAGE # Installation Methods...
More informationEND FRAMES. End frames built using pressure treated 2x4 (1 1/2" x 3 1/2") 36" 34" 7/16" pilot hole. 5 1/2" x 1/2" lag bolt 8" wheel 23"
END FRAMES End frames built using pressure treated 2x4 (1 1/2" x 3 1/2") 23" 17 1/2" (B) (B) Measure from the bottom of your stone to 1" below the lip to get your measurement. 17 1/2"(B) 36" 34" 1/2" flat
More informationThe frame sections of the china hutch are assembled with the aid of glue and spiral dowels. Dowel centers are recommended to
60 CHINA HUNT 282 ARE YOU LOOKING for a showpiece china hutch to display your elegant chinaware, antique vase, or collectibles? Here's the perfect cabinet for you, with lots of transparent glass to show
More informationThis photo more clearly shows how locating pins are used to transfer the dowel holes from the edge to front of frame. Use bar clamps till glue dries.
CHINA HUTCH 266 The frame sections of the china hutch are assembled with the aid of glue and spiral dowels. Dowel centers are recommended to ease matching of dowel holes. gant chinaware, antique vase,
More informationDisplay Case (for J&S)
Display Case (for J&S) This is constructed of maple plywood with solid maple (soft maple) edge banding. It was made to fit between a door and a kitchen cabinet, and has an elegant circular taper between
More informationTongue & Groove Cabinet Doors Copyright 2014 JaysCustomCreations.com
Tongue & Groove Cabinet Doors Copyright 2014 JaysCustomCreations.com A tongue and groove cabinet door is made up of at least 5 pieces. Two horizontal rails (blue), two vertical styles (green), and one
More information129 KITCHEN BASE CABINET 480
129 KITCHEN BASE CABINET 480 There are two sorts of kitchen cabinets: base cabinets, which sit on the floor, and wall cabinets. Base cabinets provide both storage space and work surfaces. They often house
More informationKitchen Island. By Rob Joseph Leg Dimensions. Drawer Exploded View. Leg Glue-Up
Kitchen Island y Rob Joseph eg imensions Step 1 - ut the legs () slightly longer than the dimensions given in the material list. or the thickness we need, the legs are cut from a piece of 11 2"-thick stock,
More informationHEAVY-DUTY WORKBENCH
HEAVY-DUTY WORKBENCH 2009 August Home Publishing Co. Feature Project Heavy-Duty Workbench For a low cost and a weekend of work, you can build a large, rocksolid workbench that s sure to last a lifetime.
More informationPLANS BY TOM BURY MURPHY WORKTABLE TOTAL DIMENSIONS: FOLDED UP 30 X 48 X 0 FOLDED DOWN 30 X 58 X 84
MURPHY WORKTABLE TOTAL DIMENSIONS: FOLDED UP 30 X 48 X 0 FOLDED DOWN 30 X 58 X 84 MATERIALS LIST: (2) 2 x8 x8 (3) 2 x4 x8 (1) 1 x2 x8 (1) 48 x96 3/4 plywood (2) 1-1/2 x30 continuous hinge (1) Left-side
More informationChapter 22 - Cabinets & Vanities
Chapter 22 - Cabinets & Vanities Contents Chapter 22 - Cabinets & Vanities... 22-1 Timing & Prerequisites... 22-2 Cabinets... 22-3 Cabinet Layout... 22-3 Wall Cabinets... 22-4 Assemble the Wall Units...
More informationPatrol Box Plans by David J. Yarusso Troop 609
Patrol Box Plans by David J. Yarusso Troop 609 Materials List: 1. One 4 x8 sheet of ½ thick cabinet grade (birch or oak) or AC plywood. If using AC grade, use the A grade surface on the outside for a clean
More informationPlans. Easy-to-Build Full-size Deluxe Murphy Bed Plan. For more plans, tools and hardware visit rockler.com
Easy-to-Build Full-size Deluxe Murphy Bed Plan Build a full-size Deluxe Murphy Bed complete with decorative molding and matching side cabinets! Plans For more plans, tools and hardware visit rockler.com
More informationWOODWORKING GUIDE: BASIC JOINERY
WOODWORKING GUIDE: BASIC JOINERY Close isn't really good enough. A perfect fit is what counts. When building furniture, there are many ways to construct joints. The simplest are those that use mechanical
More informationNojo Design: Large Step Cabinet: February 2012
Nojo Design: Large Step Cabinet: February 2012 The largest single piece of furniture I ve ever made is this stepped cabinet. Finished piece is 8! tall and over 10 long. This project has been great, although
More informationStrategies for panels, casework, boxes, and more. Prep Tips. Check your tool settings to ensure that when facejointing, planing, and
Goof-Proof Clamping Strategies for panels, casework, boxes, and more By Jim Harrold B Prep Tips ehind every successful glueup or project assembly you ll find one or more clamping operations that ensured
More informationDIY Wine Storage Cabinet
DIY Wine Storage Cabinet ADDICTED2DIY.COM *Before beginning this project, please read through all of the plans and the blog post. When building this project, be sure to measure your wood and cut to fit.
More informationArched. Building an. Passageway. Although my company specializes in high-end jobs
Building an Arched Passageway All photos by Brian Striegler This straightforward approach combines basic shop methods with simple site joinery to create an elegant frame-and-panel archway by Gary Striegler
More informationZeroPlay Guide Bar Jig Plans (V2.0) Micro Jig, Inc. PO Box Winter Springs, FL USA
Z2 ZeroPlay Guide Bar Jig Plans (V2.0) 0409 Micro Jig, Inc. PO Box 195607 Winter Springs, FL 32719 USA Tel: 1-407-696-6695 Web site: www.microjig.com Email: sales@microjig.com Copyright 2009 Micro Jig,
More informationBuild a Bed Designed for Readers
America s leading woodworking authority Step by Step construction instruction. Build a Bed Designed for Readers A complete bill of materials. Exploded view and elevation drawings. How-to photos with instructive
More informationMortisting Stand. Premium Plan. In this plan you ll find: America s leading woodworking authority
America s leading woodworking authority Premium Plan In this plan you ll find: Mortisting Stand Step-by-step construction instruction. A complete bill of materials. Construction drawings and related photos.
More informationIearn my living by making cabinetry not cookie-cutter
Supporting Shelves Five methods for installing by Stephen Winchester Iearn my living by making cabinetry not cookie-cutter kitchens, but one-of-a-kind pieces and custom built-ins. Every cabinet I build
More informationEssential BOX JOINT JIG
Essential BOX JOINT JIG Home in on precise finger joints with this table saw sled. By Ken Burton The box (or finger) joint is a remarkably strong, interlocking corner joint that can be quickly made on
More informationIF INSTALLING ANY OF THE PORTMAN SELF CLOSING SYSTEMS, PLEASE READ THE CORRESPONDING FITTING INSTRUCTIONS SUPPLIED WITH THE CLOSING SYSTEM FIRST
Set A Set B PFD60 Fire Door Kit FITTING INSTRUCTIONS IF INSTALLING ANY OF THE PORTMAN SELF CLOSING SYSTEMS, PLEASE READ THE CORRESPONDING FITTING INSTRUCTIONS SUPPLIED WITH THE CLOSING SYSTEM FIRST SUGGESTED
More informationMail Truck Bank Plan. Rockler Mail Truck Bank Plan
Mail Truck Bank Plan Build this nostalgic Mail Truck Bank and capture the imagination of a child! This easy-to-build plan uses our Solid Brass Mailbox Door (#55358) to commemorate the stalwart little truck
More information