1/16" Square balsa strip stock is used for the fuselage and tail surfaces structure. 10T 11T 11B (2) 10B. Pec Bea. Wingspan - 18"
|
|
- Hector Lindsey
- 5 years ago
- Views:
Transcription
1 1/16" Square balsa strip stock is used for the fuselage and tail surfaces structure. 10T 9T 8 11T 12 7T 6T F (2) Pec ea CAD Drawing by Paul radley Sheet 1 of 8
2 Nose plug is a lamination of 1/64" plywood and 1/16" balsa 10T 9T 11T 6T 5T /16" Dowel 6T 13 5 Spinner is made from 7 laminations of 1/8" balsa, 1 layer of 1/32" plywood, and one layer of 1/16" balsa 7T 5T T Peck Thrust earing CAD Drawing by Paul radley Sheet 2 of 8
3 1 1/8" Dihedral under each tip C F E D A Tips are made from 1/16" x 1/8" strip stock 1/16" x 1/8" alsa CAD Drawing by Paul radley Sheet 3 of 8
4 Wing center section is flat. 1/16" x 1/8" alsa 1 1/8" Dihedral under each tip 1/16" x 1/8" alsa on bottom only C A D E F Dihedral template for rib A Wing spars are 1/16" square balsa strip stock 1/16" x 1/8" alsa CAD Drawing by Paul radley Sheet 4 of 8
5 1/16" x 1/8" balsa strip stock Drill hole in the 1/16" x 18" strip to accept the landing gear leg. Slide the leg through the hole and then push the rear bend through rib D. Apply glue along the leg that rests against the rib and strip stock Make a left and right landing gear leg from.025" piano wire. CAD Drawing by Paul radley Sheet 5 of 8
6 Spinner Fabrication Trim the top of former 12 to the profile shown after it has been installed. Install the rear and front sections of the canopy before installing the center section. Remove the portion of the top stringer between formers 9T and 8 before installing the center canopy section. Cut this part after the wing is assembled. Use the wing to mark the location of the top spar on each side of the fuselage. Cut slots to allow the top spar to slide inside. Wing ribs A will sit flush against the outside face of these parts. CAD Drawing by Paul radley Sheet 6 of 8 The nose plug is made from a lamination of 1/64" plywood, and 1/16" balsa disks along with a key block made from 1/16" balsa laminations and a Peck thrust bearing. Step 3 - Make a template from the spinner profile. Using a sanding block and the template shape the spinner while the assembly is being turned with the electric drill. Step 4 - Using a dremel tool or something similar, trim off the 3/16" dowel where it exits the the assembly at the top of the opening formed by the bottom three disks. Step 5 - Make up the 1/16" and 1/32" plywood disks. Glue them together. Confirm the fit with the main spinner assembly. Do not glue yet. Glue your prop to the plywood/balsa disk asembly. Mark the location of the prop blades on the main spinner assembly. Cut the main spinner assembly to clear the prop blades. When satisfied with the fit the main spinner assembly can be glued to the rear disk after installing the prop shaft. Step 2 - After the glue has dried on the assembly place the dowel in an electric drill. Run the drill and with a sanding block reduce the assembly diameter to be equal to the spinner base diameter. Step 1 - Cut 7 1/8" balsa disks to 1/8" more than the spinner base diameter. Cut a 3/4" diameter hole in three of the disks. Cut a 3/16" hole in three of the remaining disks. Glue the three disks with the 3/16" holes to a length of 3/16" dowel and to each other. Glue the solid disk to the front of the assembly. Glue the three disks with the 3/4" holes to each other and then to the assembly.
7 12 4 T E E 11T 11 D D 5 9T 11 A A F-1 Tail Wheel Doors 9 6 6T F F Stab 8 7T 7 Fin 13 Wing 10T 10 5T Fuselage wing saddle pieces C C Nose plug key pieces Nose plug - Make one from 1/64" plywood and one from 1/16" balsa Spinner - Make 3 from 1/8" balsa and 1 from 1/16" balsa Spinner - Make 1 from 1/32" plywood Spinner - Make 3 from 1/8" balsa Spinner - Make 1 from 1/8" balsa CAD Drawing by Paul radley Sheet 7 of 8
8 CAD Drawing by Paul radley Sheet 8 of 8
1/16" Square balsa strip stock Wingspan - 18" Balsa filler block made from 1/16" laminations CAD Drawing by Paul Bradley Sheet 1 of 8 F2 11T 10B 11BS
F1 1/16" Square balsa strip stock alsa filler block made from 1/16" laminations A rawing by Paul radley Sheet 1 of 8 F2 13T 1/16" Square balsa strip stock for all fuselage longerons and stringers 12T 11T
More information8B 7B 6B. Wingspan - 25" CAD Drawing by Paul Bradley Sheet 1 of INCHES. Cowl pattern. 1/16" Square
R1 R2 owl pattern 1/16" Square enter Windshield Pattern 1/16" Square filler forward of stab 9T 8T 7T R3 10 R4 T1 T2 9 Side Windows Pattern Fuselage sides are built using 1/16" square stock 8 7 6 rawing
More informationCOMET 24" HELLCAT REPRODUCTION ASSEMBLY GUIDE
COMET 24" HELLCAT REPRODUCTION A RUBBER POWERED 24" WING SPAN MODEL BY PAUL BRADLEY ASSEMBLY GUIDE AUGUST 2016 CHANGES MADE TO THE ORIGINAL The following changes were made to the original Comet kit structural
More informationCOMET SENIOR DART REPRODUCTION ASSEMBLY GUIDE
COMET SENIOR DART REPRODUCTION A RUBBER POWERED 24" WING SPAN MODEL BY PAUL BRADLEY ASSEMBLY GUIDE JANUARY 2018 CHANGES MADE TO THE ORIGINAL The following changes were made to the original Comet kit structural
More informationI do hope you build and enjoy a model from this plan package. Paul Bradley
There are several notes I need to provide to aid you with the enclosed package. The original kits used 1/16" balsa. Since I wanted to print these directly on balsa sheet I developed the parts for 1/32"
More information1/8" Balsa 8B 7B 6B. For Radio Control. Wingspan - 25" CAD Drawing by Paul Bradley Sheet 1 of 12 INCHES. Cowl pattern.
R1 1/8" alsa R2 owl pattern 1/16" Square enter Windshield Pattern 1/16" Square filler forward of stab 9T 8T 7T R3 10 R4 T1 T2 9 Side Windows Pattern Fuselage sides are built using 1/16" square stock 8
More informationEasy Built Models Kit JX-02 MiG-15 Conversion to Rubber-Power By Matt Payne, October 2011
Easy Built Models Kit JX-02 MiG-15 Conversion to Rubber-Power By Matt Payne, October 2011 The fuselage is restructured. The Jetex-related structural components, the stock keel parts, and the formers are
More informationCleveland Quickie Luscombe Silvaire
Cleveland Quickie Luscombe Silvaire This plan package is not a 100% copy of the original kit. As you make your way through the instructions you will see the differences. Here s just a few of them: The
More informationFUSELAGE CONSTRUCTION
FUSELAGE CONSTRUCTION Note: prior to building and gluing on the work surface use protective covering on your building surface. (wax paper or clear wrap) Fit the laser cut Fuselage Front and Fuselage Rear
More informationI do hope you build and enjoy a model from this plan package. Paul Bradley
There are several notes I need to provide to aid you with the enclosed package. The original kits used 1/16" balsa. Since I wanted to print these directly on balsa sheet I developed the parts for 1/32"
More informationYour kit contains the following parts. Please check your kit for any missing or damaged parts before starting construction.
Your kit contains the following parts Please check your kit for any missing or damaged parts before starting construction COMPLETE KIT PARTS LIST 1 Plan Sheet #1 1 Plan Sheet #2 2 Decal Sheet 2 White Tissue
More informationLARK. Classic Legal Precision Stunter RSM DISTRIBUTION. presents. Charles Mackey. Wing Area 570sq. Wingspan 52.
RSM DISTRIBUTION presents LARK By Charles Mackey Photo _ Bob Hunt Classic Legal Precision Stunter Wingspan 52 Length 39.5 Wing Area 570sq Motor 35-46 www.rsmdistribution.com Page 2 Thank you for purchasing
More informationPiper Cherokee /3 scale. Construction Manual
Piper Cherokee 140 1/3 scale Construction Manual STAB CONSTRUCTION 1. Remove foam cores from cradle and place on flat surface. Inspect pieces before you epoxy halves together making sure leading and trailing
More informationTHE APOGEE A 100-INCH AMA DURATION SAILPLANE FROM DYNAFLITE
THE APOGEE A 100-INCH AMA DURATION SAILPLANE FROM DYNAFLITE Apogee is the intermediate sailplane designed to be competitive in AMA duration contests. Effective spoilers, rudder and full flying stabilizer
More informationBuild and Fly This Bristol Fighter
Build and Fly This Bristol Fighter How You Can Build a Simplified Flying Scale Model of One of the Greatest British World War Planes By LAWRENCE McCREADY The finished model looks like the real thing Though
More information84 WING SPAN MESSERSCHMITT BF-109
84 WING SPAN MESSERSCHMITT BF-109 (COPYRIGHT PROTECTED 2014) ALL RIGHTS RESERVED MEISTER 84 ME-109 SIERRA GEAR UPDATE PLEASE NOTE: THE MAIN GEAR MOUNTING PLATE FROM SIERRA IS NOT SQUARE. YOU HAVE TO ROUND
More informationSTICK 2 IT. Fuselage Construction:
RCCD 2014 CLUB PROJECT STICK 2 IT Fuselage Construction: The fuselage is constructed without the use of a set of plans. The fuselage will be constructed on your previously prepared work surface and by
More informationSPORTSTER BY FRED TUXWORTH
SPORTSTER BY FRED TUXWORTH For those who like gas models to look like real airplanes, this sturdy performer is just about tops. Best -looking model of the year Biplane wings may be fitted. This gives you
More information96 WING SPAN SPITFIRE (COPYRIGHT PROTECTED 2014) ALL RIGHTS RESERVED
96 WING SPAN SPITFIRE (COPYRIGHT PROTECTED 2014) ALL RIGHTS RESERVED GENERAL INSTRUCTIONS Should you elect to use the recommended Door Skin, which is 1/8 mahogany plywood measuring 36 x 88. Have it cut
More informationThe model boasts of twin fuselages and three fins
An Experimental Twin Tractor One of the Most Unique and Finest Fliers Ever Presented. If You Want Something Different, Build and Fly This One By FELIX GUTMANN The model boasts of twin fuselages and three
More informationRudder h 1mm alum. Retract unit mount 2 layers of 3mm liteply between 0.8mm birch ply (Total thickness 7.6mm)
R Retract unit mount 2 layers of 3mm liteply between 0.8mm birch ply (Total thickness 7.6mm) Rudder post 5mm balsa Rudder h 1mm alum Seat horn on 3mm bal then edge with balsa to Also applicable to tailplane
More informationC-180 Builder s Manual
C-180 Builder s Manual. May 20, 2002 Last revised July 11, 2002 Copyright! 2002 Douglas Binder, Mountain Models www.mountainmodels.com sales@mountainmodels.com (719) 630-3186 1 Required Equipment! Xacto
More informationLANIER - Ultimate Pitts - INSTRUCTIONS. Additional Parts Required. (12) 4-40 blind nuts (Dubro #606)
Additional Parts Required (4) or more channel radio with 7-8 servos..91-2.2 two stroke or 1.20-1.84 four stroke engine Appropriate Master Airscrew prop and Hayes mount for your engine. 3 Tru-Turn spinner
More informationCitabria Pro. Aerobatic Parkflyer. by Joel Dirnberger
Citabria Pro Aerobatic Parkflyer by Joel Dirnberger Revision C: December 21, 2004 Citabria Pro Building Instructions Length: Wingspan: Wing Area: Flying Weight: Wing Loading: Functions: Specifications:
More informationF100 Super Sabre instructions.
F100 Super Sabre instructions. The F100 is a Jet model for the Wemotec 480 Minifan. Start with taking the parts out of the sheet and sand of the connection tabs. Instructions RBCkits F100 Super Sabre 1
More informationLoLo. A sporty parkflyer with an Old Timer flair! Designed by: Tres Wright Kitted by: Park Scale Models
LoLo A sporty parkflyer with an Old Timer flair! Designed by: Tres Wright Kitted by: Park Scale Models http://www.parkscalemodels.com/ Assembly Instructions General Information The laser cutting process
More informationTHE SWALLOW. An interesting, simple, all-balsa speedster of crashproof design. by MALCOLM J. ABZUG
THE SWALLOW An interesting, simple, all-balsa speedster of crashproof design. by MALCOLM J. ABZUG DESIGNED primarily for the purpose of testing a new type of monocoque fuselage design, the Swallow proved
More informationNationals Flying Scale "Champ" Not Only National Winner but a Realistic Plane That Flies Two Minutes Consistently By HENRY STRUCK
The little "big" plane that won at the 1941 Nationals, with its striking appearance and performance. Nationals Flying Scale "Champ" Not Only National Winner but a Realistic Plane That Flies Two Minutes
More informationAVRO R/C Scale Model Instructions CONTACT INFORMATION. Designed by Peter Rake Modified by M.K. Bengtson
R/C Scale Model Instructions CONTACT INFORMATION Designed by Peter Rake Modified by M.K. Bengtson Manufactured and Distributed by: Bengtson Company e-mail: sales@aerodromerc.com Web Site: www.aerodromerc.com
More information4. Bevel the LE face of HS1-HS11 to match the horizontal stab leading edge sweep angle.
BEFORE YOU BUILD 1. Unroll each sheet of the plans. Roll them inside out so that they will lie flat on the building surface. 2. Assemble the tools that you will need to build each section so that they
More information90 WING SPAN P-51D MUSTANG (COPYRIGHT PROTECTED 2014) ALL RIGHTS RESERVED
90 WING SPAN P-51D MUSTANG (COPYRIGHT PROTECTED 2014) ALL RIGHTS RESERVED GENERAL INSTRUCTIONS This design is basically an enlargement of the very popular fun scale Mustang 60 Size. You can build it light
More informationMercurE Mini Old Timer Electric Model
MercurE Mini Old Timer Electric Model MercurE Specifications Wingspan: 31.6 in. Length: 20.6 in. Wing Area: 153 sq. in. Weight (Ready to Fly): 4.9 to 5.4 oz. Wing Loading: 4.6 5.1 oz. / sq. ft. Version
More informationSE5a Wing Panels rev 1.0
SE5a Wing Panels rev 1.0 The top and bottom wings are different. They might look the same but the bottom wing has one less rib and some rib spacing difference. This is due to where the wooden interplane
More informationRSM DISTRIBUTION Presents
RSM DISTRIBUTION Presents MOSQUITO By Jack Sheeks Photo _ Jack Sheeks Semi Scale Twin Stunter Wing Span: 58" Length: 37-3/4 Area: 579 sq. in. Engine: Two.35 -.40 www.rsmdistribution.com Call (951) 678
More informationULS Cherokee. Ultra Low Speed aircraft for indoor RC flying. Zippkits. Specifications: Required to complete:
Zippkits ULS Cherokee Ultra Low Speed aircraft for indoor RC flying. Specifications: Span- 28 inches Wing Area- 151 Sq/In Wing Loading- 3.0 ounces/ft Weight- 3.5 ounces RTF Build time- 1-2 Hours Radio-
More informationFalke Build Instructions
A totally unofficial translation of the Falke Build Instructions The Falke (falcon) mini DLG is produced and marketed by Modellbau Thiele, Germany (www.modellbau-thiele.de), email webmaster@modellbau-thiele.de.
More informationA Piaggio-inspired park flyer
Clark Salisbury's SkyTwin A Piaggio-inspired park flyer B efore I discuss building the SkyTwin, I should explain my reasons for designing, building, and flying such an aircraft. I have always been fascinated
More information84 WING SPAN MESSERSCHMITT BF WIN G S P A N
84 WING SPAN MESSERSCHMITT BF-109 10 2 WIN G S P A N MESSERSCHMITT BF-109 THIS IS A VERY EASY PLANE TO BUILD BEFORE YOU START The fuselage self jigging system used an easy accurate assembly. But, attention
More informationJAMISON SPECIAL. Building Guide
JAMISON SPECIAL Building Guide WING Mark then drill holes for wing jig rods. Slide Ribs onto jig rods Mark the rib positions on 1/16 x 1 trailing edge, 1/4 x 1/4 leading edge & 1/4 x 1/4 spars Pin ribs
More informationFibertech N More cc 103 SUPER CHIPMUNK ASSEMBLY MANUAL. pg. 1
Fibertech N More 50-60cc 103 SUPER CHIPMUNK ASSEMBLY MANUAL pg. 1 Introduction Thank you for choosing Fibertech N More 103 Super Chipmunk. We have taken great effort into making this kit a great plane
More informationSPUNKY ASSEMBLY MANUAL
SPUNKY ASSEMBLY MANUAL Please read the tips section at the back of this manual regarding the use of laser cut parts. The proper removal and preparation of these parts is important. When laser cut, some
More informationInstruction manual. ALOUETTE 3 For 600 size
Instruction manual ALOUETTE 3 For 600 size Dear customer, Thank you for purchasing a Smartmodel fuselage All our team wishes you a lot of fun for building and good flights. For 600 size or 50 Nitro power
More informationTHE STREAMLINER! A super Class D fuselage model
THE STREAMLINER! A super Class D fuselage model by CHRISTIAN D. BERGER THE two most important characteristics of a contest model are its climb, and gliding ability. For, after all, you have to get up high
More informationTANDY WALKER'S A 2nd CLASS BOMBER 10 to 20. FW:10 Class A Bomber LG. FW:11 Class A Bomber Pylon Primary Sructure
TANDY WALKER'S A 2nd CLASS BOMBER 10 to 20 FW:10 Class A Bomber LG I finished up the landing gear (LG) this morning and shot a couple of pictures for you to see. The first picture shows the LG with 3/32"
More informationRESolution V2 Manual
RESolution V2 Manual Note for the German Manual: Yellow Bottle thick CA Pink Bottle Med CA Blue tube 5 minute Epoxy Green tube 90 Minute Epoxy Construction of the Fuselage Step 1: Cover the plan with a
More informationLANDING GEAR. 1. Fit landing gear into slots on bottom of fuselage.
LANDING GEAR 1. Fit landing gear into slots on bottom of fuselage. 4. Use channel-lock pliers to press blind nuts into position (note: drilled hole should be slightly smaller than shaft of blind nut for
More informationBuild this little "Chihuahua" A miniature engine in a little ship... But the combination produces big time performance. by David D.
Build this little "Chihuahua" A miniature engine in a little ship... But the combination produces big time performance. by David D. Grant Up and Atom! "Chihuahua" has a snappy climb. Small and compact,
More informationSAAB JAS 39 Gripen. Building Instructions Designed by: Steve Shumate. Taken From:
SAAB JAS 39 Gripen Building Instructions Designed by: Steve Shumate Taken From: http://www.rcgroups.com/forums/showthread.php?t=308830&page=1 Lightly tack glue the paper templates to the foam sheets using
More informationAn All-Balsa Sportster
An All-Balsa Sportster A REMARKABLE FLIER OF UNIQUE DESIGN THAT WILL GIVE YOU MANY ENJOYABLE BUILDING AND FLYING HOURS By STAN D. MARSH Contributions by Felix Gutmann This model was designed primarily
More informationTaylorcraft Indoor / Cul-De-Sac Flyer
Taylorcraft Indoor / Cul-De-Sac Flyer Taylocraft Specifications Wingspan: 28.0 in. Wing Area: 117 sq. in. Weight (Ready to Fly): 3.0 3.1 oz. Wing Loading: 3.7 3.8 oz. / sq. ft. LIABILITY RELEASE In that
More information100 WING SPAN MESSERSCHMITT BF-109 (COPYRIGHT PROTECTED 2014) ALL RIGHTS RESERVED
100 WING SPAN MESSERSCHMITT BF-109 (COPYRIGHT PROTECTED 2014) ALL RIGHTS RESERVED BEFORE YOU START The fuselage self jigging system used an easy accurate assembly. But, attention to detail when cutting
More informationFLITZEBOGEN-2 Assembly instructions
FLITZEBOGEN-2 Assembly instructions Trim the end of the fuselage to the length of 925mm from the nose. Be careful to avoid splitting the carbon fibers. Sand the base of the stab mount in preparation for
More informationLANIER - Giles % - INSTRUCTIONS
Additional Parts Required (4) or more channel radio with 4 servos..25 -.36 two stroke or.40 -.52 four stroke engine Appropriate Master Airscrew prop and Hayes mount for your engine. 2-1/2 Tru-Turn spinner
More informationA Flying Grumman Fighter How You Can Build a Model of One of the Latest U.S. Navy Fighters That Is an Excellent Flier By WILLIAM WINTER
A Flying Grumman Fighter How You Can Build a Model of One of the Latest U.S. Navy Fighters That Is an Excellent Flier By WILLIAM WINTER The completed model is faithful to scale and detail THE Grumman F3F-1
More information51
51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 Spitfire MkVIII by Geoff Pentland for 29 35 engines from Aero Modeller December 1960. Near-scale model of the famous WWII fighter will complete the most
More informationA large prop insures high performance. Cleverly designed to give a realistic appearance
Cleverly designed to give a realistic appearance A large prop insures high performance A Vought Fighter That Flies Complete Data from Which You Can Build an Excellent Performing Flying Scale Model of the
More informationSTRATOSPHERE CONTEST MODEL
STRATOSPHERE CONTEST MODEL A Super-Duration Fuselage Plane With Extremely High Power-Weight Ratio It Has Made a Flight of Thirty- Five Minutes Construction of the light hut strong frame work is simple
More informationBob Hildebrand s Kitten. The Kitten. By Bob Hildebrand
Bob Hildebrand s Kitten The Kitten By Bob Hildebrand HERE S A 100 SQ. IN JOB WITH WAKEFIELD PERFORMANCE AYE there, laddie,,arre ye Scotch we' th' rubberrr? If you are the kind who doesn't appreciate the
More informationA Class A Gas Model That Looks Like a Full Scale Plane and Performs Like a Contest Ship
A Class A Gas Model That Looks Like a Full Scale Plane and Performs Like a Contest Ship By SAL TAIBI 1941 NATIONAL WINNER The little plane glides in with all the realism of a full scale craft The plans
More informationfresh from the 1970s A WW1-looking home-built, by Laddie Mikulasko April
by Laddie Mikulasko A WW1-looking home-built, fresh from the 1970s The Der Jager s light wing loading allows it to climb quickly. Sport aerobatics are comfortable. SEVERAL YEARS AGO, in one of the aircraft
More informationThe Olympic DLG. (Discus launch glider) by Chris Brislin
The Olympic DLG (Discus launch glider) by Chris Brislin 1 Contents Parts List/ What you need 3 Before you begin 4 Wing Construction 5-9 Pod Construction 9-13 Tail assembly 13-? Control linkages 9-10 Finishing
More informationA Flying Twin Motor DOUGLAS DB-7 A Realistic Model Bomber. This Is Easy to Build and Fly
A Flying Twin Motor DOUGLAS DB-7 A Realistic Model Bomber. This Is Easy to Build and Fly By SIDNEY STRUHL A fine flyer; just like the full-size plane Twin motors give a long and steady flight The three-wheel
More informationBuilding Instructions P-51 BF109
Building Instructions P-51 BF109 Sport model for.015 engines. Legal for SSC Warbird Lanier R/C Inc. P. O. Box 458 Oakwood, Ga. 30566 Copyright 2004 Lanier R/C Inc. Important information: Please inspect
More informationHigh performance 90mm fiberglass jet
High performance 90mm fiberglass jet Assembly manual For intermediate and advanced fliers only! Specs Wingspan: 1255mm Fuselage length: 1250mm Flying weight: 2600-3000g Wing area: 22.6 dm² Wing loading:
More informationSZD-10 bis CZAPLA ASSEMBLY MANUAL IN PICTURES
1 RUDDER Plan and parts: 2 Assembly steps: Photo above: glue together rudder spar, ribs and trailing edge. Clamp spar to a flat surface (chipboard on the photo) and make sure the straight aligment of the
More informationTHERE WERE many attractive sport
R / C replica of H a r r y Williamson's 1 9 5 1 U k i e by NICK ZIROLI Sr. THERE WERE many attractive sport and stunt control-line models designed in the late 1940s and 1950s, and I've built many of them.
More informationParkflyer F6F Hellcat
Parkflyer F6F Hellcat Page 1 of 19 MOLT MODELS Background Design Philosophy When I was first introduced to this hobby seventeen years ago I saw my first WWII warbird and I was hooked. Several years later
More informationHobby Lobby Zip Supplementary instructions Please refer to the included drawings while using these assembly instructions
Materials needed: 15 or 30 minute epoxy Medium CA Masking tape Scotch tape Servo Tape Wax paper Tools Needed: Pencil or marker Flat building surface Hobby knife or razor blade 7/64" or 3mm drill bit 3/16"
More informationBy HARRY BARR... A cute little rubber job that is easy to build and fly. Full-size plans on next two pages.
By HARRY BARR... A cute little rubber job that is easy to build and fly. Full-size plans on next two pages. "Hangar Rat" owes its existence to the "Sig Parasol," a simple, easy-to-fly, tissue-covered profile
More informationIntroducing The Cloud Models Westland Whirlwind
Produced by Cloud Models,Deopham Road,Morley,Wymondham, Norfolk,NR18 9AA E-mail sales@cloudmodels.com web site cloudmodels.com Introducing The Cloud Models Westland Whirlwind By Tricks Thank you for purchasing
More informationE-AERO EPP PITTS KIT From BP HOBBIES. Parts Included in kit
E-AERO EPP PITTS KIT From BP HOBBIES Parts Included in kit Thank you for purchasing the BP Hobbies/E-aero EPP Pitts. Please take the time to read through the instruction manual before beginning the build.
More informationFighting Sopwith Snipe
Fighting Sopwith Snipe FAMOUS SNIPE IN MODEL FORM OFFERS DETAIL AND FLIGHT TO BUILDERS By Joseph H. Wherry YOU fellows who still enjoy building scale models of World War I aircraft will now be able to
More informationCurtiss XP-40Q Construction Notes
Curtiss XP-40Q Construction Notes Thank you for purchasing this kit-we hope you will enjoy building and flying the last of the Curtiss P-40 series of fighter planes. Start construction by assembling the
More informationPfalz E1 Monoplane 48 EZ Build Version
Pfalz E1 Monoplane 48 EZ BUILD Pfalz E1 Monoplane 48 EZ Build Version R/C Scale Model Instructions CONTACT INFORMATION Designed by M.K. Bengtson Prototype by Robert Hoffman Manufactured and Distributed
More informationBuild and fly this exact scale 43-in. control-line version of the popular Cessna private plane.
Seeing double? Clever photography gives that illusion but actually it s only the model 140 in the foreground. Author Stahl (right) does fly both the job he is holding and his real Cessna 14 pictured in
More informationMillennium RC presents The New and Improved (now even easier to build and cover!) SSX X-Trainer Build Kit
Millennium RC presents The New and Improved (now even easier to build and cover!) SSX X-Trainer Build Kit Wing span: Approx. 42 Wing Area: 504 sq. in. Wing Loading: 6.71 oz/ sq. ft. Introduction: The Slow
More informationMOUNTAIN MODELS P-51 Mustang. 1/12 Scale Electric Park Flyer. Copyright Mountain Models
1 MOUNTAIN MODELS www.mountainmodels.com P-51 Mustang 1/12 Scale Electric Park Flyer Wingspan: 37, Wing Area: 254 sq. in., Weight: 15 to 19.5 oz Instructions Version 1.4, May 23, 2007 Kit Contents: 2 1.
More informationBuilding A Flying Curtiss "Osprey" How You Can Create One of the Finest Flying Scale Models You Have Ever Built
Building A Flying Curtiss "Osprey" How You Can Create One of the Finest Flying Scale Models You Have Ever Built By WILLIAM WINTER Though of biplane type it has excellent flying qualities THE OSPREY, an
More informationObtained from Omarshauntedtrail.com
DaveintheGrave's Halloween Props Animated Crawling Skeleton Build a life-size skeleton torso that realistically crawls across the lawn one arm at a time. 1. Motor Base and Linkage Assembly BASE - I used
More informationSwitchBack Senior. SwitchBack Senior Specifications
SwitchBack Senior SwitchBack Senior Specifications Wingspan: 55.4 in. Length: 41 in. Wing Area: 597 sq. in. Weight (Ready to Fly): 34 to 37 oz. Wing Loading: 8.2 to 8.9 oz. / sq. ft. Version 1.05, March
More informationLANIER Dominator INSTRUCTIONS
ADDITIONAL EQUIPMENT NEEDED TO COMPLETE YOUR DOMINATOR 500 General 3.2 to 4.2 Size two stroke R/C engine, muffler, and engine mount Gas or glow fuel line Minimum of 4 channel radio set required (4-5) 70
More informationNote - the nose ribs and are thinner than the main ribs. These nose ribs will use a thinner rib cap than the ribs. This is per design.
Stabilizer rev 1.2 The SE5a stabilizer is the heartbeat of the tail and is recreated like the full scale version. All tail pieces depend on the stabilizer. It uses the steel fittings, pulleys, inspection
More informationThank you for your purchase of the Lee Ulinger, FoamtanaS, Yak-55, or Extra 330 3D Depron foam, Aerobatic airplane.
Thank you for your purchase of the Lee Ulinger, FoamtanaS, Yak-55, or Extra 330 3D Depron foam, Aerobatic airplane. Tools you will need to build Recommended additional items: #11 hobby knife Motor: Hacker
More informationEPP Rebel Z 35. White Red w/ Blue Orange w/ Blue Orange w/burgundy Other. Specs. Color - Bottom White Black Checkers Silver Checkers Other Checkers
EPP Rebel Z 35 Specs AUW ~10.0oz Width 35.28 Length 34.67 Wing Area 1.44 sqft Horz Area 2.35 sqft Vert Area.91 sqft
More informationS.E.5a (Build Instructions)
S.E.5a (Build Instructions) Specifications Wingspan: 38 cm Length: 31cm Flying Weight: 41 Channels: 3 (Rudder Elevator Throttle) Suggested Receiver: 3Ch Brick Motor: 7mm Geared Motor Airframe Only Kit
More informationBuild the Spitfire: Step-By-step. Pack 3 Stages 21-30
Pack Stages 2-0 Contents Stage Page Number 2 72-74 22 75-78 2 79-8 24 82-84 25 85-88 26 89-9 27 92-94 28 95-97 29 98-00 0 0-05 Editorial and design by Continuo Creative, 9-4 North Road, London N7 9DP All
More informationBUILDING INSTRUCTIONS FOR FINEWORX. Miles. 2M Class Competition Glider. Congratulations! You have purchased our Miles, 2M Class Competition Glider.
BUILDING INSTRUCTIONS FOR FINEWORX Miles 2M Class Competition Glider Congratulations! You have purchased our Miles, 2M Class Competition Glider. The Miles is the first offering from FINEWORX, a new company
More informationMesserschmitt Bf 109F-2 Version January 2005
Assembly Manual for Messerschmitt Bf 109F-2 Version 1.2 29 January 2005 Designed by Terry Majewski Copyright 2005 Thomas A. Jacoby and WarbirdKits.com 1 Materials Kit Contents This kit includes the following
More informationBuilding Tips This model can be built using the following types of adhesives:
Page 1 Building Tips This model can be built using the following types of adhesives: Epoxy (with or without microballons) Odorless cyanoacrylate (CA) with accelerator UHU Creativ for Styrofoam (or UHU
More informationNieuport 11 Bebe. R/C Scale Model Instructions. CONTACT INFORMATION The Nieuport 11 Bebe was designed by Peter Rake and M.K.
Nieuport 11 Bebe 49 Nieuport 11 Bebe R/C Scale Model Instructions CONTACT INFORMATION The Nieuport 11 Bebe was designed by Peter Rake and M.K. Bengtson Manufactured and Distributed by: Bengtson Company
More informationBy ROBERT VAIL SMITH. A clean streamline job with a unique power plant. A speedy ship with tandem "props" revolving in opposite directions
A speedy ship with tandem "props" revolving in opposite directions A clean streamline job with a unique power plant The Koolhoven "Pursuit" Unusual Looks and Flying Qualities Grace This Exact Scale Model
More informationBob's Card Model
Bob's Card Model www.bobscardmodels Conair C S 2F (Tracker) water-bomber(1:72) Securité Civile's converted Tracker, used for patrol duty, but also for water-bombing (3200 litres). Together with the Canadairs
More informationBy Pvt. Ted Lanham COULD BE A FREE-FLIGHT JOB OR CONTROLLINER. THIS SEMI-SCALE CLASS B GASSIE HAS EYE-APPEAL, CONTEST-LIKE PERFORMANCE.
By Pvt. Ted Lanham COULD BE A FREE-FLIGHT JOB OR CONTROLLINER. THIS SEMI-SCALE CLASS B GASSIE HAS EYE-APPEAL, CONTEST-LIKE PERFORMANCE. Rearwin Speedster was used as basis for this design. Model, ready
More informationA Flying Belanca Aircruiser How You Can Build a Flying Scale Model of a Famous Cargo Plane That Includes Many Fine Details of Construction
It performs well with a flying propeller The finished model with scale propeller A Flying Belanca Aircruiser How You Can Build a Flying Scale Model of a Famous Cargo Plane That Includes Many Fine Details
More informationDRAFT COPY BUILDING INSTRUCTIONS FOR BLACKBURN BUCCANEER S2 VERSION 1 (BETA BUILD) BY MARK DOUGLAS
BUILDING INSTRUCTIONS FOR BLACKBURN BUCCANEER S2 VERSION 1 (BETA BUILD) BY MARK DOUGLAS COPYRIGHT MARK DOUGLAS 2011 THIS IS A "SHORT" KIT FOR EXPERIENCED BUILDERS AND FLYERS ONLY, DESIGNED BY A SHED DWELLING
More informationR/C Scale Model Instructions
Fokker D. V 43 Fokker D.V 43 R/C Scale Model Instructions CONTACT INFORMATION Designed by M.K. Bengtson Prototype by Bert Ayers Manufactured and Distributed by: Bengtson Company e mail: sales@aerodromerc.com
More informationBOBS CARD MODELS. De Haviland Dash-8 water-bomber (1:72)
BOBS CARD MODELS www.bobscardmodels.com De Haviland Dash-8 water-bomber (1:72) A Canada de Haviland Dash-8 fitted with a large water tank, complements the French aerial firefighters' fleet of Canadairs
More informationFOKKER DVIII 36 2/3 1/9 TH S
FOKKER DVIII 36 2/3 1/9 TH S R/C S M I Designed by M.K. Bengtson Prototype and Instruction Manual by Franny Brodigan M D : Bengtson Company e-mail: sales@aerodromerc.com www.aerodromerc.com F DVIII Thank
More informationBUILDING THE FUSELAGE FRAME 6
KIT 305 DHC-2 BEAVER COPYRIGHT 2011 BY PAUL K. GUILLOW, INC. WWW.GUILLOW.COM Before starting the construction of your model, study the plan and construction procedure carefully so that you will have a
More informationFokker D8 Master Instructions
Fokker D8 Master Instructions Rev 1 Congratulations on your new project. The Fokker D8 is a marvellous subject that highlights the success of a monoplane design. The construction of the plane is similar
More information