Lashing wire. Ceiling mesh tray WN2 WEF For lashing of wires in mesh trays. Lashing wire is used for mounting in mesh trays.

Transcription

1 Lashing wire For lashing of wires in mesh trays. WEF-0011 Diam Breaking load kg 100 m HTR-2303 Lashing wire, stainless steel, white PVC HTR-2313 Lashing wire, stainless steel, black PVC HT-2304 Lashing wire, white PVC HT-2314 Lashing wire, black PVC Lashing wire is used for mounting in mesh trays. Ceiling mesh tray WN2 For installation in ceilings. Wire Ø4.4. B 2000 Electro-galv. Hot dip galv. Stainl. steel (AISI316) Electro-galv. White80 A B Ceiling mesh tray WN A Mounted in ceilings with Ceiling bracket WN16. Mounted under desks with Ceiling bracket WN

2 Ceiling bracket WN16 For installation of Ceiling mesh tray WN2. Electro-galv. Hot dip galv. Stainl. steel (AISI316) Electro-galv. White80 Ceiling bracket WN Ceiling mesh tray WN2 must be mounted with Ceiling bracket WN16. Ceiling mesh tray WN2 mounted under desks with Ceiling bracket WN16. Earth clamp W79 Suitable for mounting on Junction box plate W24. Used for protective earthing. Electro-galv. 100 st Earth clamp W Earth clamps W79 are intended for use when the earthing of mounting plates for the installation of machines complying with regulations for use of high tension current is required. The junction box plate s (mounting plate s) oval holes facilitate the moving of the Earth clamp W79 so that it is always located under the machine casing. If the machine s earth clamp is not approved for splicing of earth cable, this must pass in unbroken state through the machine s earth clamp to the earth clamp in the junction box plate. Wibe Junction box plate W24 and Earth clamp W79 are approved by the National Electrical Inspectorate in accordance with annotation S24-138/

3 Cover plate W16 Mounted with Screw set W36/W36C under 90 bends, T- and X-junction if one needs to level out differences in levels between tray and junction. A Plate thickness Pre-galv. Pre-galv. White30 Cover plate W Cover plate W Cover plate W Cover plate W Cover plate W Mounted with Screw set W36/ W36C under X-junction W13/40 if one needs to level out differences in height between tray and bend. 110

4 Dividing strip 39 Mounted to divide a cable tray or lighting trunking into two or more channels in order to separate different types of cables and pipes. Mounted with Support band W6. Plate thickness H Pre-galv. Pre-galv. White30 Pre-galv. White80 Dividing strip 39/ Dividing strip 39/ Plate thickness H Hot dip galv. Stainl. steel (AISI316L) Dividing strip 39/ Dividing strip 39/ *EAN-code= Part.nr+C (control figure) Used to separate tray or trunking in two or more ducts thereby separating control cables from other cables and pipes. The hole structure at distances of 250 permits two fixing opportunities with Support bands W6 even after cutting. 111

5 Insert piece W39 Insert piece W39 is used to join Dividing strips W39. WEF-0021 Plastic Insert piece W Insert piece W39 is used to join Dividing strips W39 and is mounted on Support bracket/joint W7 or Internal cantilever arm W17/40. When mounting over Internal cantilever arm W17/40, break away plastic bit from component. Support band W6 The Support band W6 is mounted to fix the lateral position of one or several Dividing strips 39. L Pre-galv. Support band W Support band W Support band W Support band W Support band W Support band W Support band W Support band W6 is mounted to fix one or more Dividing strips 39 laterally. The holes in the support band and the locking pins in Dividing strip 39 allow for a fixed division with intervals of

6 Tele-conduit 36 With knock-out holes Tele-conduit is installed where a separate tray is required for low-tension cables. B C Pre-galv. Hot dip galv. Pre-galv. White80 Tele-conduit Tele-conduit Tele-conduit Make a hole for cable passage by pushing out the washer from below with a screw driver or similar. 113

7 Cover W5 Length The cover is used for screening control cables and in dusty and dirty premises. t B Pre-galv. Pre-galv. White30 Cover W Cover W Cover W Cover W Cover W Cover W Cover W Cover W Cover W t B Hot dip galv. ZINKPOX White80 Cover W Cover W Cover W Cover W Cover W Cover W Cover W Cover W Cover W Used for screening of control cables and in dusty and dirty premises. Covers must be mounted on cable trays with Cover clamp W

8 Cover clamp W62 Used for fixing covers on Trays W1 and W3 as well as on Lighting trunking W70/W71. Stainl. steel (AISI304) Cover clamp W Cover clamp W62 used for fixing the covers on Cable tray W1 and W3 as well as on Lighting trunkings W70 and W71. Start by pressing the Cover clamp W62 over the sides of the cover. Then snap the cover over the folded edges of the tray. 6 Cover clamps W62 are needed per cover. 115

9 Combi bracket 53 Used for mounting cable trays, mesh trays and cable ladders on seemed roofing sheet etc.,-0031 Hot dip galv. Plastic Combi bracket Insulating plate Breaking load* Type of roofing sheet Insulating plate Permitted load Bandsheet Prelac Copper sheeting Bandsheet Prelac Copper sheeting No Yes No Yes F1=100 kg F2=50 kg F3=100 kg F4=50 kg * Loading values and fixing of roof sheet - follow the supplier s recoendations Test have been made of: Bandsheet Prelaq BLX t=0.6 SSAB tunnplåt Copper sheeting annealed SS t=0.6 Tightening torque at test=60nm Combi bracket 53 mounted on seamed roofing sheet. Alternative mounting of Combi bracket 53. In order to avoid contact between Combi bracket 53 and copper sheeting, Insulating plate 54 must be used. Alternative mounting of Combi bracket 53 and Insulating plate 54. Cable ladder mounted across the seams of the roofing sheets with Combi bracket 53, Wall bracket 11/25 and Screw set 22S. Cable ladder mounted along the seams of the roofing sheets with Combi bracket 53, Wall bracket 11/25, Screw set 22S, Pendant/ Fixing rail 24/48 and T-bolt 26F. Mesh tray mounted along the seams of the roofing sheets with Combi bracket 53 and accessories from the Mesh tray program. Mesh tray mounted across the seams of the roofing sheets with Combi bracket 53 and accessories from the Mesh tray program. 116

10 Strip fixing W44 The Strip fixing W44 enables strapping of cables in an unperforated tray. WEF-0022 Plastic (black) Strip fixing W *EAN-code= Part.no+C(control figure) The Strip fixing W44 is provided with double sided adhesive tape and is attached to the tray bottom. Alternatively, blind rivets or self-tapping screws can be used. When mounting with double sided adhesive tape, the surface on the tray bottom must be wiped clean. Loads may not be applied until after 24 hours. Full adhesion is obtained after 72 hours in 21 C. Ideal application temperature is C. Application below normal room temperature is not recoended. Each Strip fixing W44 can be split up in 2 to 6 pieces. Supplied with 50 pieces in a plastic bag. Protection strip W48 Used to protect the cables from damage. WEF-0030 Plastic Protection strip W When cutting a cable tray you can mount Protection strip W48 to protect the cables from damage. 117

11 Luminaire bracket W50 For mounting light fittings between two parallel Cable trays W1/W3 or Lighting trunking W70/W71. Dimension H is specified when ordering. H Plate thickness Pre-galv Pre-galv. White80 Luminaire bracket W50 ** *** **Selected with respect to height of the light fittings ***H=100 Repair paint Galvafroid for repair of damaged places on pre-galvanized or hot dip galvanized cable trays and accessories. Repair paint for minor damages of powder coated products. WEF-0013, 0016 Volume l Anti-corrosive paint "Galvafroid", tin Repair paint White RAL 9003 Gloss 30, spray bottle Repair paint White RAL 9010 Gloss 80, spray bottle Galvafroid used to increase the protection of cut or damaged places.applied with a colour brush. Repair paint in spray bottle for repainting of minor paint damages. 118

12 Screw set 22S For mounting of Ceiling bracket 5 on Pendant/Fixing rail 24/34 and Cantilever arm 80 on Vertical piece 7 or Wall bracket 80 etc. Hot dip galv. Stainl. steel (AISI316) Screw set 22S (bolt MVBF8x16+nut M6MF8) Spring nut M8 For permanent mounting of fittings (instrument cabinets etc.) on Pendant/Fixing rail 24/48. Hot dip galv. Spring nut M Mounting set W78 For mounting of Threaded rod M10 W76 in plate or light concrete ceilings. Hot dip galv. Mounting set W78 (washer diam.50+nut M6M10) Screw set W36 For mounting of pendant attachments in Support bracket/joint W7. Electro-galv. Stainl. steel (AISI316) Screw set W36 (bolt MVBF8x16+nut M6MF8) Screw set W36C Slotted screw used for mounting of pendant attachments in Support bracket/joint W7. Electro-galv. Screw set W36C (Slotted screw M8x16+nut M6MF 8 toothed)

13 Screw set W37 For assembly of Pendant attachment W21 and Ceiling attachment W31 with Pendant rail W32. For joining of Pendant rail W32. Electro-galv. Stainl. steel (AISI316) Screw set W37 (bolt MVBF 8x35+nut M6MF 8) Screw set W38P Used for mounting of joints, bends, junctions, Shade ledge W26 and Integrated ceiling support channel W27. Screw set W38P pierces through lacquered surfaces securing potential balancing. N. B. The joints must be unlacquered. Patented. Electro-galv. Dacromet Electro-galv. White60** Screw set W38P *Ean-code= Part.no+C (control figure) **White laquered screw head Screw set W34 For mounting Tray W3 on Cantilever arm 50. For mounting Junction box plate W24 in Tray W3, Lighting trunking W70 and W71. For mounting Locking clamp W77 or Angle bracket W8 onto Pendant rail W32. For assembly of Angle bracket W8 (light fitting bracket). For joining of Installation Trays W4 and installations with Profile W-swing 2. Dacromet Electro-galv. Stainl. steel (AISI316) 100 st Screw set W34 (bolt MSCS 6x12+nut M6MF6) *EAN-code= Part.nr+C (control figure) Screw W40 For locking of T-joint W29 in open junctions. Electro-galv Screw W40 (screw RXS ST 5.5x13-H) Locking plug W41 For quick locking of joints, bends and branches in cable trays and lighting trunking. WEF-0004 Plastic Locking plug W

14 T-bolt 26F Used for mounting with Pendant/Fixing rails. WEF-0002 D A L T-bolt 26F/M8 T-bolt 26F/M10 (For P/F-rail 24/48) D L A Electro-galv. Hot dip galv. Stainl. steel (AISI316) T-bolt 26F M T-bolt 26F M T-bolt 26F M T-bolt 26F M T-bolt 26F M T-bolt 26F M Max permitted extraction force T-bolt 26F M8/M10 + P/F-rail 24/48 +Washer 8,4x19x1,5 T-bolt 26F M8 + P/F-rail 24/48 + Washer 9x35x2 T-bolt 26F M10 + P/F-rail 24/48 + Washer 9x35x2 Installation of Pendant/Fixing rail on floor (or wall) with Angle bracket 5L and T-bolt. Check the position mark on the bolt to ensure the right position of the T-bolt in the rail. T-bolt M8 makes it possible to mount through the perforation of Pendant/Fixing rail 24/

15 Expansion bolts Electro-galvanized, hot dip galvanized or stainless steel AISI316. For installation of all Wibe cantilever arms and vertical pieces. Stainless steel D L G Electro-galv Hot dip galv. (AISI316) Expansion bolt M6x40** Expansion bolt M6x65** Expansion bolt M8x50** Expansion bolt M8x95** Expansion bolt M8x120** Expansion bolt M10x Expansion bolt M10x Expansion bolt M10x Expansion bolt M12x Expansion bolt M12x Expansion bolt M12x Expansion bolt M16x Expansion bolt M16x Expansion bolt M16x Expansion bolt M20x Expansion bolt M20x * EAN-code= Part.no+C (control figure) ** M6 and M8 are delivered with an extra washer with a larger diameter. This washer must be mounted close to the cantilever arm or vertical piece. The smaller standard washer must be put on top of the bigger washer close to the nut. D 1 = Drill diameter M = Installation depth B = Min. drilling depth T = Material thickness Data for installation Tightening D 1 B M T moment Dim Nm M6x M6x M8x M8x M8x M10x M10x M10x M12x M12x M12x M16x M16x M16x M20x M20x

16 Expansion bolts Extraction force Permitted extraction force in kn for various concrete qualities Installation Concrete class Dim depth C25 C30 C35 C40 M M M M M M M M M M M M M Transverse force Permitted transverse force in kn for various concrete qualities Installation Concrete class Dim depth C25 C30 C35 C40 M M M M M M M M M M M M M

17 Fixing system 124

18 Concrete screw MMS-S For installation with cantilever arms and vertical pieces. Concrete screw with hexagonal head and special thread constructed for safe fixing in concrete or brickwork. Suitable for fixing of tubes, electrical installations, rails, handrails, machines, ventilating ducts, wood constructions. Easy to install High extraction values are obtained due to the special thread. The drill diameter is the same as the root diameter of the screw which gives a solid fixing inside the hole. Can be dismounted and reinstalled without reduced extraction force. A weaker drill can be used compared to using anchor, expansion bolt, screw and plug. Suitable in environments which are fire classified. Installation of cantilever arms. Installation of vertical pieces. Concrete screw MMS-S Electro-galvanized A = Drill diameter B = Min. installation depth C = Min. drilling depth F = Extraction force kn** T = Transverse force kn N = Width of jaws **For concrete class C25 F kn T kn N ØxL A B C Number/ package MMS-S 6x x MMS-S 6x x MMS-S 6x x MMS-S 7.5x x MMS-S 7.5x x MMS-S 7.5x x MMS-S 10x x MMS-S 10x x MMS-S 10x x MMS-S 12x x Washer 7.0x16x1.5 Electro-galv. is included 2 Washer 8.4x19x1.5 Electro-galv. is included 125

19 Concrete screw MMS-S Hot dip galvanized A = Drill diameter B = Min. installation depth C = Min. drilling depth F = Extraction force kn** T = Transverse force kn N = Width of jaws **For concrete class C25 F kn T kn N ØxL A B C Number/ package MMS-S 6x x MMS-S 6x x MMS-S 6x x MMS-S 7.5x x MMS-S 7.5x x MMS-S 7.5x x MMS-S 10x x MMS-S 10x x MMS-S 10x x MMS-S 12x x Washer 7.0x16x1.5 Hot dip galv. is included 2 Washer 8.4x19x1.5 Hot dip galv. is inclcluded Concrete screw MMS-S Stainless steel AISI316 Concrete screw with soldered phosphatized carbon steel tip. L 2 L1 A = Drill diameter B = Min. installation depth C = Min. drilling depth F = Extraction force kn** T = Transverse force kn N = Width of jaws **For concrete class C25 F kn T kn N ØxL 1 /L 2 A B C Number/ package MMS-S 7.5x50/ x50/ MMS-S 10x70/ x70/ MMS-S 12x80/ x80/ Washer 8.4x24x2.0 AISI316 is incl. 126

20 Concrete screw MMS-S FL Electro-galvanized Concrete screw with flange. A = Drill diameter B = Min. installation depth C = Min. drilling depth F = Extraction force kn** T = Transverse force kn D = Flange diameter N = Width of jaws **For concrete class C25 F kn T kn N ØxL D A B C Number/ package MMS-S FL 6x x MMS-S FL 6x x MMS-S FL 6x x MMS-S FL 7.5x x MMS-S FL 7.5x x MMS-S FL 10x x MMS-S FL 10x x MMS-S FL 12x x MMS-S FL 12x x Concrete screw MMS-S FL Hot dip galvanized Concrete screw with flange. A = Drill diameter B = Min. installation depth C = Min. drilling depth F = Extraction force kn** T = Transverse force kn D = Flange diameter N = Width of jaws **For concrete class C25 F kn T kn N ØxL D A B C Number/ package MMS-S FL 6x x MMS-S FL 6x x MMS-S FL 6x x MMS-S FL 7.5x x MMS-S FL 7.5x x MMS-S FL 10x x MMS-S FL 10x x MMS-S FL 12x x MMS-S FL 12x x

21 Concrete screw MMS-PAN Electro-galvanized For installation of Pendant strip W33. Panheaded concrete screw, electro-galvanized and yellow chromated. Torx-recess. F kn T kn ØxL A B C E A = Drill diameter B = Min. installation depth C = Min. drilling depth E = Screw head diameter F = Extraction force kn** T = Transverse force kn **For concrete class C25 Number/ package Part.No. C* Torx MMS-PAN 5x T-20 5x MMS-PAN 5x T-20 5x MMS-PAN 6x T-30 6x MMS-PAN 7.5x T x MMS-PAN 10x T-40 10x Installation of Pendant strip W33. Mounting with JR-clamp. Concrete screw MMS-PAN SH Electro-galvanized For installation of Ceiling attachment W31 or Tube pendant attachment W73. Concrete screw with extra big panhead, electro-galvanized and yellow chromated. Torx-recess. F kn T kn ØxL A B C E A = Drill diameter B = Min. installation depth C = Min. drilling depth E = Screw head diameter F = Extraction force kn** T = Transverse force kn **For concrete class C25 Number/ package Torx MMS-PAN SH 7.5x T x Installation of Ceiling attachment W

22 Concrete screw MMS-ST Electro-galvanized For installation of eye nuts. The screw is specially developed for safe fixing in concrete. Suitable for tube installations, electrical installations, rails, handrails, machines, ventilating ducts, wood constructions. A = Drill diameter B = Min. installation depth C = Min. drilling depth E = Length of thread engagement F = Extraction force kn** T = Transverse force kn N = Widths of jaws M = English thread F kn T kn N DxL 1 L 2 M A B **For concrete class C25 C E Number/ package MMS-ST 7.5x x70 53 M MMS-ST 10x x80 65 M Installation of eye nut. Concrete screw MMS-I Electro-galvanized For installation of Pendant M8 or M10. High extraction values are obtained due to the special thread. The drill diameter is the same as the root diameter of the screw which gives a solid fixing inside the hole. Can be dismounted and reinstalled without diminished extraction force. A weaker drill and less drilling depth can be used compared to using anchor, expansion bolt, screw and plug. Suitable in environments which are fire classified. F kn T kn N DxL 1 L 2 M A B A = Drill diameter B = Min. installation depth C = Min. drilling depth F = Extraction force kn** T = Transverse force kn N = Widths of jaws M = Metrisk gänga **For concrete class C25 C Number/ package MMS-I 7.5x x93 M8/M Installation of Threaded rod M8 or M

23 Eye screw MMS-R Electro-galvanized For installation of wires in ceiling. A = Drill diameter B = Min. installation depth C = Min. drilling depth F = Extraction force kn** T = Transverse force kn **For concrete class C25 F kn T kn ØxL A B C Number/ package MMS-R 6x x Light concrete screw Electro-galvanized For installation in porous concrete. Torx-recess. B = Min. installation depth E = Head diameter F = Permitted extraction force kn F kn ØxL B E Number/ package Torx Light concrete screw 8x T-40 8x Expansion nail Electro-galvanized/ Aluminium For fixing of light details in concrete. A = Drill diameter B = Min. installation depth C = Min. drilling depth ØxL A B C Number/ package Expansion nail 5x x Mounting tool for Eye screw MMS-R Electro-galvanized. Number/ package Mounting tool for Eye screw MMS-R

24 Bitro adapter Electro-galvanized + plastic. The Bitro adapter must be installed direct on Haer drill SDS PLUS. Drilling machine can be used. Suitable for drilling only in C25 concrete. For drill D L Number/ package Bitro adapter 5, yellow Bitro adapter 6, green Bitro adapter 8, red Bitro adapter 10, blue Turn off the haer function of the drilling machine. Install the Bitro adapter on the drill. Check that the adapter locks the drill to avoid turning. Put in Torxbits or Magnetic socket or Square peg + Socket 16/18. When removing the adapter tilt it lightly and pull the bit, magnetic socket or the square peg. When mounting use a drilling machine with torque regulator. Otherwise be very careful. If you let the machine continue to run when the screw is in bottom it is very easy to destroy the tip of the drill or that the drill gets stuck or broken. The risk increases with the length of the drill. Magnetic socket for Concrete screw MMS-S Untreated steel. Dim D Number/ package Magnetic socket 10x x Magnetic socket 13x45** x **Can also be used for MMS-I. Socket for Concrete screw MMS-S Untreated steel. To be used together with Square peg. Dim D Number/ package Socket x Socket x

25 Bits holder Stainless steel AISI304. Number/ package Bits holder 11x Square peg Untreated steel. To be used with Socket 16 and 18. Number/ package Square peg 3/8x Torxbits Untreated steel. To be used with Concrete screw MMS-PAN SH. Number/ package Torxbits TX 30x Torxbits TX 40x

26 Haer drill SDS PLUS Untreated steel. Dim Cutting length of the drill Number/ package Haer drill SDS PLUS 4x x Haer drill SDS PLUS 5x x Haer drill SDS PLUS 5x x Haer drill SDS PLUS 5.5x x Haer drill SDS PLUS 5.5x x Haer drill SDS PLUS 6x x Haer drill SDS PLUS 6x x Haer drill SDS PLUS 6x x Haer drill SDS PLUS 7x x Haer drill SDS PLUS 7x x Haer drill SDS PLUS 8x x Haer drill SDS PLUS 8x x Haer drill SDS PLUS 10x x Haer drill SDS PLUS 10x x Haer drill SDS PLUS 12x x Haer drill SDS PLUS 16x x Haer drill SDS PLUS 20x x Masonry drill WBL/WBE Tungsten carbide tip.tool steel shank with plated finish. Masonry drill WBE 4x x Masonry drill WBE 5x x Masonry drill WBL 5x x Masonry drill WBE 5.5x x Masonry drill WBL 5.5x x Masonry drill WBE 6x x Masonry drill WBL 6x x Masonry drill WBE 7x x Masonry drill WBL 7x x Masonry drill WBL 7x x Masonry drill WBL 8x x Masonry drill WBL 8x x Masonry drill WBL 10x x Masonry drill WBL 10x x Masonry drill WBL 12x x Masonry drill WBL 16x x Masonry drill WBL 20x x

27 Concrete screws - Loadings Mounting of Wibe concrete screws To use Wibe concrete screws is both safe and easy. No special tools or machines are required. The screw performs an exact adapted thread in the bedding which means that no control of the tightening moment is required. The extraction force of a Wibe concrete screw is better than that of an expansion bolt with the same diameter You can choose a smaller diameter of a concrete screw than that of an expansion bolt and still receive the same extraction force. The same concrete screw can be re-used. Mounting instruction Use a drill suitable to the screw. Drill the hole. Switch off the haer function. Mount the Bitro adapter on the drill. Pull in a bit or socket suitable for the screw to be used. Mount with drilling machine. Wibe concrete screws can also be mounted with regular hand tools as box sockets. 1. Drill a hole with the same diameter as the root of the screw (for 6 drill 5, for 7.5 drill 6, for 10 drill 8 and for 12 drill 10 ). The drill depth must be at least 20 deeper than the installation depth. 2. Blow the hole free from dust. 3. Mount the concrete screw close to the application bedding, no defined tightening moment is required. Note don t tighten the screw with a higher moment than stated on the package or technical data. Extraction forces, in kn, depending on installation depth in uncracked concrete C25. Calculated values with a safety factor of 3.0. Installation depth MMS-5 MMS-6 MMS-7.5 MMS-10 MMS Transverse forces Concrete screw MMS Dimensioned transverse force in kn. Concrete screw MMS-5 MMS-6 MMS-7.5 MMS-10 MMS Screw diameter Breaking torsional moment (Nm) Recoended max tightening moment (Nm) Spacing The above values are valid when the distance from the nearest corner or free edge to the screw is at least 10 x screw diameter. The spacing between two screws must be minimum 20 x screw diameter. 134

28 Low density anchor TLF Hot dip galvanized For fixing in light concrete or clinker concrete. For medium or heavy installations. Unique advantages: Long expansion area and heavy expansion very high loading values The expansion can be directed - superior loading values even at small edge distances. Very quick installation drives in and expands with a haer and Haer tool TLF-S WEF-0006 DxL D 1 Drill diameter Number/ package Low density anchor TLF 8x65** x Low density anchor TLF 12x x Low density anchor TLF 12x x Low density anchor TLF 16x x **One Haer tool is incl. in each package. Loading - All loadings refer to mounting in light concrete Y 500 Max Tightening moment M=Nm Extraction force F1 kn Transverse force kn TLF 8x65 mounted with wood screw TKX Fzb SPAX-5x TLF 12x100 mounted with hexagon head wood screw T6S 4.6 Fzv 8x TLF 12x145 mounted with hexagon head wood screw T6S 4.6 Fzv 8x TLF 16x130 mounted with hexagon head wood screw T6S 4.6 Fzv 10x Max permitted load F on Cantilever arm Kg kn Kg kn Kg kn Kg kn Kg kn TLF 8x 65 TLF 12x TLF 12x TLF 16x Drill with recoended drill diameter, see above. (Without pre-drilling in quality Y400 and Y450). Low density anchor TLF installed with Haer tool TLF-S. Put the haer tool into the installation hole of the low density anchor and bolt the anchor. Lower the distance. Expand the anchor by means of the Haer tool. 135

29 Haer tool TLF-S Untreated steel. For driving in and expansion of the Low density anchor TLF. L Number/ package Haer tool TLF-S 12x Haer tool TLF-S 12x Haer tool TLF-S 12x Put the Haer tool into the installation hole of the Low density anchor and bolt the fixing (without pre-drilling in quality Y400 and Y450). Lower the distance. Expand the anchor by means of the Haer tool. Sleeve TLF-H12 Hot dip galvanized. To be used together with Low density anchor TLF 12x100 or 12 x145 in order to raise the transverse force performance. Number/ package Sleeve TLF-H Put the sleeve on the Low density anchor. (See instructions for Low density anchor TLF). Bolt the Low density anchor with the sleeve in level with the wall. 136

30 Adapter TLF-A12 Electro-galvanized. To be used together with Low density anchor TLF 12x100 or 12x145 in order to receive an interior M10 thread. Suits Pendant M10. WEF-0007 Number/ package Adapter TLF-A Screw the Adapter into the expanding Low density anchor. Pendant M10 fits in the Adapter. Angled bracket TLF-F12 Pre-galvanized. To be mounted with Low density anchor TLF 12x100 or 12x145 and can be used as fixing for band or wire installations. Number/ package Angled bracket TLF-F Mount the Angled bracket on the Low density anchor. (See instructions for Low density anchor TLF). Bolt the Low density anchor with the Angled bracket into the bedding and check that it is secured. 137

31 Express hanger SVH Stainless steel AISI316. For fixing in concrete, natural stone, solid brick or plate. Used for installation of armatures close to the ceiling (with locking block) as well as for hanging of integrated ceilings, armatures, electrical-, tube- or ventilating equipment. Mounting tool SVH-T, for mounting to the right installation depth, is included in the package. Cover plate is included only for SVH-E1. Drill Min. drilling depth Number/ package Express hanger SVH-E Express hanger SVH-E2** **Cover plate not included. Loading Permitted load capacity at safety factor 3 at extraction Concrete C25 kn Solid brick kn Express hanger SVH-E Express hanger SVH-E Hole must be drilled with a 8 drill, drilling depth minimum 30. Drive in the Express hanger with the Mounting tool SVH-T. The installation depth always turns out to be the right. The short and stiff wire ends grip effectively into the sides of the hole resulting in a safe and strong fixing. Mounting of wires. Cover plate hides the hole. Mounting close to the ceiling with Securing spring SVH-L. Express hanger SVH can also be used for installation of Fixing strip TRB and TGB. When the fixing strip is turned into position it self-locks. Can also be locked with screw, rivet or lashing wire for extra security. At a visible installation, hide the hole with a cover plate. Delivered together with SVH-E1. 138

32 Securing spring SVH-L Stainless steel AISI304. For installation of armatures close to ceiling. Number/ package Securing spring SVH-L For installation of armatures close to the ceiling. Maximum loading per securing spring is 4 kg. Mounting tool SVH-T Electro-galvanized. For installation of Express hanger SVH. Number/ package Mounting tool SVH-T For installation of Express hanger SVH. The installation depth will always turn out to be the right. 139

33 Fixing strip TGB Pre-galvanized. For pendant installation and clamping Cold-rolled and galvanized sheet metal, perforated for easy installations. For fixing tools as Express hanger SVH or Low density anchor TLF with Angled bracket TLF-F12. Number/ Package Fixing strip TGB 11x (25m) 105 Can be mounted with Express hanger SVH. Can be mounted with Low density anchor TLF and Angled bracket TLF-F12. Can easily be mounted with other suitable fixing tools. Fixing strip TRB Stainless steel AISI304. For pendant installation and clamping. Stainless steel band AISI304 for qualified installations in all type of environments. Express hanger SVH or Low density anchor TLF with Angled bracket TLF-F12 can be used as fixing tools. Number/ package Fixing strip TRB 11x (10m) 42 Can be mounted with Express hanger SVH. Can be mounted with Low density anchor TLF and Angled bracket TLF-F12. Can easily be installed with other suitable fixing tools. 140

34 Fixings - Ogebe The Ogebe fixing is a patented fixing intended for use when mounting plating with a thickness of and 13 gypsum board. Pendants, cantilevers and holed strips can be mounted with these fittings. Technical data Material Material treatment Surface treatment Maximum load Cold-rolled sheet steel SS Case-hardened Electro-galvanized See load tables Nut Bolt Washer Locking Nut M8, SMS 2165 FZB M8 x 16 FZB SRB 13.5 x 26 x 2 FZB ø12 0,7 0,9 Drill a 12 dia. hole. A 10 drill can be used if one increases the hole dia. by slanting the electric drill. Breaking load Place the accompanying washer over the thin legs. Insert the legs through the drilled hole and fold the broader legs towards each other. If sealing is required, a standard sealing mass from building retailers can be used. Mount the pendant, bracket or holed strip with the enclosed bolts and nuts. (The nut should always be a locking nut). The load applied at an equi-distance between 2 beams 600 apart. The values are taken from Swedish National Testing Institute Report Fixing type E Fixing types D, ED Fixing type Eg F3 F3 F3 F1 F1 F1 F3 F3 F3 F2 F2 F2 141

35 Ogebe fixing type E The Ogebe fixing type E is used for mounting in sheeting or board material. The following can be mounted: hole straps, pendants, ducts and pipings etc. Electro-galv. Ogebe fixing type E Mounting of Pendant rail W32. Mounting of Pendant rail W32 with Ogebe fixing type E direct in lighting trunking. Mounting of Ceiling attachment W31 on Ogebe fixing type E. Mounting of hole strap. Stand installation on wall. Suspension of duct or pipe. Mounting of holed beam. A wire can be mounted directly in the Ogebe fixing type E. The Ogebe fixing type E can be mounted direct into Support bracket/joint W7. 142

36 Ogebe fixing type D The Ogebe fixing type D is used for mounting in sheeting or board material. The following can be mounted: pendant fittings etc. Electro-galv. Ogebe fixing type D Mounting of ceiling attachment W31 on fixture, type D. Use Screw set W36 or W36C. Ogebe fixing type D or ED can be mounted in lighting trunking as light fitting. 143

37 Ogebe fixing type ED The Ogebe fixing type ED is used for mounting in sheeting or board material. The following can be mounted: suspension devices, light fittings etc. Electro-galv. Ogebe fixing type ED Mounting of Pendant attachment W21 or Tube pendant attachment W73 with Ogebe fixing type ED. Use screw set W36/W36C. When mounting Ceiling attachment W31 on cable trays/lighting trunking, the load can be distributed onto two or more fixings. This allow for lateral adjustment. Installation of holed beam. Use Screw set W36/W36C. Mounting of light fittings in plate metal ceiling. Stand installation on wall. Use Screw set W36/W36C. Ogebe fixing type D or ED can be mounted in lighting trunking as light fitting. 144

38 Ogebe fixing type Eg The Ogebe fixing type Eg is intended for mounting in single gypsum boards. Eg Electro-galv. Ogebe fixing type Eg Eg mounted in single gypsum board. Stand installation on wall. 145

39 Integrated ceilings Ceilings from Wibe provide undreamt of possibilities to build different types of system ceilings with very high demands on functionality. You build using reliable, reputable components which are easy to install and combine in an almost neverending number of variations. 146

40 , Acoustic lamina We can supply acoustic lamina for baffle frames, wire baskets and ceilings with T-profiles. There are several manufacturers on the market offering lamina of varying thicknesses, colours, suface coverings and structures. The lamina comply with current standardes for fire-protection and are available with various sound absorption factors. It is possible to select the colour of your choice Cable trays, lighting trunking, mounting fittings and accessories come in standard version in pre-galvaniced or pre-galvanized with white paint finish (RAL 9010) design in accordance with the Zinkpox method. A celling often gives a room its character.exploit the possibilities of choosing a coulor scheme for your ceiling thereby creating a pleasing atmosphere. We can supply the whole of our prograe in RAL colour of your choice and with lustre you desire. 147

41 Open ceilings Components 1. Cable tray W1 2. Support bracket/joint W7 3. Tube pendant attachment W73 4. Pendant strip W33 5. T-joint W9 (alt. W29) 6. Junction box plate W24 7. Screw set W36 8. Screw set W38P 9. Threaded rod M10 W76 148

42 Ceilings with sound baffles Components 1. Cable tray W1 2. Support bracket/joint W7 3. Pendant attachment W21 4. Ceiling attachment W31 5. Pendant rail W32 6. T-joint W9 (alt. W29) 7. Screw set W37 8. Screw set W38P 9. Sound baffles 10. Position retainer W43 149

43 Ceilings with wire baskets Components 1. Cable tray W1 2. Support bracket/joint W7 3. Pendant attachment W21 4. Ceiling attachment W31 5. Pendant rail W32 6. T-joint W9 (alt. W29) 7. Junction box plate W24 8. Screw set W37 9. Screw set W38P 10. Wire baskets 150

44 Ceilings in corridor B Components 1. Cable trays and Lighting trunking 2. Suspension 3. Junction box plate 4. Support bracket/joint 5. Baffles, baskets etc. 6. W-swing profiles 7. W-swing wall bracket 8. Shade ledges, angle strips, integrated ceiling support channels and wall trays B= please state when ordering 151

45 Sound baffles Wibe baffle frames are constructed of side and gable sections which are cut to measure and mounted in accordance with customer requirements. Baffles with hooks Baffles with rings Baffles with hooks The bottoms of the baffles and trays are on the same level. Hinged hooks The hooks allow the baffles to be lowered. However, this necessitates that the space between tray and baffle may not be less then 25. Clearence hooks The hooks provide clearence and define the space between tray and baffle. Absorbents The baffles are provided with optional acoustic lamina. There are several producers in the market who can offer acoustic lamina in various thickness, colours and design. Ordering When ordering please specify the following measurements: L = Length of baffle B = Width of baffle C = Clearence measurement Baffles with suspension rings The rings are adapted to the W-swing profiles used in corridor installations. In this type of installation the baffles end up lower than the tray bottom. Position retainer 2 Position retainers W43 per baffle must be mounted diagonally. Mounting When installing the baffles directly in the trays normally 2 Hinged hooks are fitted to the one end of the baffles and 2 Clearence hooks in the other. At installation without distance between baffle and tray 4 Hinged hooks must be used. Material Made of pre-galvanized sheet steel + powder coated white. Other colours can be quoted. Installation with Profile W-sving 2 on Wall bracket W-sving 2. Suspended baffle. Installation of suspended baffle in Profile W-swing 3. Installation of suspended baffle in Profile W-swing 2 mounted on Profile W-swing 4A. Installation with tray and Profile W-swing 5. Suspended baffle. Installation with tray and Profile W-swing 1. Suspended baffle. 152

46 Wire baskets Wire baskets are an alternative to baffles. They provide an open and airy atmosphere. In shops and stores they provide good possibilities for hanging advertisements, bargain offers and decorations. The grating can be manufactured of wire with different diameters. Note that the shape of the mesh can either be square or rectangular. Design The welded grating is aesthetically attractive by simplicity, stability and plasticity. Abundance of variation due to the mesh pattern 50x50. Bigger mesh sizes can be offered. Standard pattern 50x50x4. Material Automatic welding of steel. Surface treatment Powder coated Ordering Please state the following L = Length of basket () B = Width of basket () 153

47 154

48 Accessories Sound baffles The following accessories are included in an unassembled sound baffle: 4 Corners, 2 Hinged hooks, 2 Clearence hooks, 2 Side profiles and 2 Gable profiles. Hinged hooks and clearence hooks can be replaced with suspension rings when necessary. The baffles are easy to assemble without any tool. Gable profile Length Pre-galv. White30 Gable profile Gable profile Side profile Side profile for hook Side profile for suspension ring Length Pre-galv. White30 Side profile for hook Side profile for hook Side profile for hook Side profile for hook Side profile for hook Side profile for hook Side profile for hook Side profile for hook Side profile for hook Please state length of profile when ordering Clearance hook Distance between baffle and tray Electro-galv. Clearance hook Clearance hook Clearance hook Clearance hook

49 Hinged hook Distance between baffle and tray Electro-galv. Hinged hook Hinged hook Hinged hook Suspension ring Length Electro-galv. Suspension ring Suspension ring Reinforced profile Length White30 Reinforced profile Reinforced profile Corner Pre-galv Corner

50 Gypsum clip Used to mount gypsum wallboards in baffle frames. Steel strip Gypsum clip Gypsum boards in Wibes baffle frames must have dimensions that are 20 smaller than the size of the baffle. The clip will keep the board in place. Position retainer W43 Support W42 Lock the gypsum clip by pressing down the tab. The gypsum clip suits a 9 thick board. Normally it is enough with 4 gypsum clips pro baffle. The clips must be mounted diagonally. WEF-0017 Position retainer W43 Two pcs are mounted per baffle. Support W42 Mounted in T-joint W9 as a support for cables. White plastic Position retainer W Support W Position retainer W43 holds the sound baffles in the correct position. W 43 is snapped tight into the edge of the cable tray or lighting trunking. Support W42 is mounted at T-joint W9 to prevent the cables from gliding out over the corner of the cable tray or lighting trunking. W42 is snapped tight into the edge of the tray. 157

51 Frame clip W90 Enables clip mounting in baffle frame. Pre-galv. Frame clip W90 (screw RXS Combi B6x19, fzb) The Frame clip W90 is clamped tight under the edge of the section. Mounting of light fittings on Reinforced profile. Installation of air component. Mounting of decoration strip etc. T-section is easily mounted with Frame clips W90 in the baffle frames. In large frames an extra support for the absorbent lamina can be required. Install a T-section with 2 Frame clips W90. Light fitting mounted in baffle frame. 2 T-profiles mounted with 4 Frame clips W

52 Ceilings in corridor 159

53 Profile W-swing 1/40 A profile that will simplify service and maintenance, used for mounting on trays with edge height c/c is standard. Other c/c measurements can be manufactured on request. White30 Profile W-swing Installation with tray on both sides and Profile W-swing 1 hanging on tray edge. Suspended baffle, folding in both directions. Installation with tray and Profile W-swing 1. Suspended baffles, folding in both directions. The trays have pendular suspension from ceiling. Profile W-swing 1/60 A profile that will simplify service and maintenance, used for mounting on trays with edge height c/c is standard. Other c/c measurements can be manufactured on request. White30 Profile W-swing 1/ Installation with tray on both sides and Profile W-swing 1 hanging on tray edge. Suspended baffle, folding in both directions. 160 Installation with tray and Profile W-swing 1. Suspended baffles, folding in both directions. The trays have pendular suspension from ceiling.

54 Profile W-swing 2 A profile that will simplify service and maintenance. 600 c/c is standard. Other c/c measurements can be manufactured on request. Pre-galv. Pre-galv. White30 Profile W-swing Installation with Profile W-swing 2 on Wall bracket W-swing 2. Suspended baffle, folding in both directions. Ceiling installation with Profile W-swing 2. Suspended baffle, folding in both directions. When joining, Ceiling bracket W31 can be both joint and ceiling bracket. Mounted with Screw set W34. Profile W-swing 2 can be suspended in Pendant attachment W21. Mounted with Screw set W34. Profile W-swing 2 can be suspended in Pendant strip W33. Mounted with Screw set W

55 Wall bracket W-swing 2 Used for installation with Profile W-swing 2. Pre-galv. Pre-galv. White30 Wall bracket W-swing Wall bracket W-swing 2 mounted on pendant or direct on wall. Profile W-swing 2 mounted on Wall bracket W-swing 2 with Screw set W34. The profile can easily be adjusted in the oval holes of the wall bracket and the profile. Infinitely variable lengthwise and ± 20 towards wall. 162

56 Profile W-swing 3 A profile that will simplify service and maintenance. 600 c/c is standard. Other c/c measurements can be manufactured on request. White30 Profile W-swing Installation with tray and Profile W-swing 1, Wall bracket W-swing 2 with Profile W-swing 2 and pendant with Profile W-swing 3. Hanging baffles, folding in both directions When joining, Ceiling bracket W31 can be both joint and ceiling bracket. Mounted with Screw set W34. Profile W-swing 3 can be suspended in Pendant attachment W21. Mounted with Screw set W34. Profile W-swing 3 can be suspended in Pendant strip W33. Mounted with Screw set W

57 Profile W-swing 4A A profile that will simplify service and maintenance. 600 c/c is standard. Other c/c measurements can be manufactured on request. White30 Profile W-swing 4A For suspension of baffles, Profile W-swing 4A is used in combination with Profile W-swing 2. Mounted with Screw set W34. Profiles W-swing 2 och W-swing 4A mounted with Screw set W34. W-swing 4A can be suspended in Pendant attachment W21. W-swing 4A can be suspended in Pendant strip W33. When joining, Ceiling bracket W31 can be both joint and ceiling bracket. Mounted with Screw set W

58 Profile W-swing 5 A profile that will simplify service and maintenance. 600 c/c is standard. Other c/c measurements can be manufactured on request. White30 Profile W-swing Installation with tray and Profile W-swing 5. Baffle in level with tray and folding in both directions. Shade ledge W26/40 Used as a support for ceilings mounted between cable trays with edge height 40. Plate thickness Pre-galv. Pre-galv. White30 Shade ledge W26/ Shade ledge W26/40 is hung over the side edge of the cable tray. Shade edge W26/40 is used as a support for ceilings mounted between cable trays. Also suitable for Lighting trunking W70/ W71. Mounted along the side edges of the cable tray or the lighting trunking. Shade list W26/40 is locked tight in the tray by pinching the ends in under the tray edge with pliers. 165

59 Shade ledge W26/60 Used as a support for ceilings mounted between cable trays with edge height 60. Plate thickness Pre-galv. Pre-galv. White30 Shade edge W26/ Shade ledge W26/60 is hung over the side edge of the cable tray. Shade edge W26/60 is used as a support for ceilings mounted between cable trays. Mounted along the side edges of the cable tray. Shade list W26/60 is locked tight in the tray by pinching the ends in under the tray edge with pliers. Integrated ceiling support channel W27/40 Used as a support for ceilings mounted between cable trays with edge height 40. Plate thickness Pre-galv. Pre-galv. White30 Integrated ceiling support channel W27/ Integrated ceiling support channel W27/40 is hung over and mounted along the side edge of the cable tray and is used as a support for ceilings mounted between cable trays. Also suitable for Lighting trunking W70/W71. Integrated ceiling support channel W27/40 is locked tight in the tray by pinching the ends in under the tray edge with pliers. 166

60 Integrated ceiling support channel W27/60 Used as a support for ceilings mounted between cable trays with edge height 60. Plate thickness Pre-galv. Pre-galv. White30 Integrated ceiling support channel W27/ Integrated ceiling support channel W27/60 is used as a support for ceilings mounted between cable trays. Mounted along the side edge of the cable tray. Integrated ceiling support channel W27/60 is locked tight in the tray by pinching the ends in under the tray edge with pliers. Angle strip W46 Used as a support for ceiling installations. Plate thickness Pre-galv. Pre-galv. White30 Angle strip W Angle strip W46 is mounted directly onto wall, column or similar as a support for baffles or ceiling lamina. 167

61 Wall tray W60/40 Wall tray with edge height 60 used for mounting of ceiling in corridor. The tray is mounted directly onto the wall. L Pre-galv. Pre-galv. White30 Wall tray W60/ Wall tray W60 is mounted directly onto the wall. Mounting of ceiling in corridor when canalisation on one side is required but with the same functionality as for cable trays on both sides. Wall tray W60/60 Wall tray with edge height 60 used for mounting of ceiling in corridor. The tray is mounted directly onto the wall. Plate thickness Pre-galv. Pre-galv. White30 Wall tray W60/ Wall tray W60/60 is mounted directly onto the wall. Mounting of ceiling in corridor when canalisation on one side is required but with the same functionality as for cable trays on both sides. 168

62 Installation examples Use Vertical piece 2F at installations in corridors with gypsum walls. The installation can easily be adjusted both vertically and horizontally and will not be effected of vibrations in the walls. Example of corridor installation. This way of mounting reduce the obliquity of the cable tray. Example of installation with uneven loadings. The installation has been reinforced with lashing wires. The wire can be fixed to the ceiling or the ceiling bracket. Internal cantilever arm can be mounted right over support bracket/joint. Mounting of Pendant rail W32 with Ogebe fixing type E direct in lighting trunking. The Ogebe fixing type E can be mounted direct into Support bracket/joint W7. Ogebe fixing type D or ED can be mounted in lighting trunking as light fitting. 169

63 170

64 171

65 172

66