HP-2 / HP-4 Wall Wash Recessed Spackle & Visible Flange Installation Instructions Overview

Transcription

1 Overview NOTES All power connections should be installed according to local/national codes by a Certified Electrician. This installation requires proper support as each luminaire is being installed. DO NOT attempt to join luminaires together on the floor. Damage may result when lifted. HELPFUL VIDEOS 0-0V Dimming Universal & Robust Joints Simple Plug-Together Wiring Step 3 Opening Luminaires Page 5 Step 5 Joining Luminaires Page 8 Step Rough-Ins & Mounting Options Pages 2-3 Protected by one or more US Patents: 89563; D702,39; D702,390; D700,732 Step 2 Identification & Preparation Page 4 Ceiling Step 4 Mounting Starter to Structure Pages 6-7 This is a hypothetical build to show the capabilities of this luminaire family and mount type. Your build may vary. Step 6 Securing Luminaire Joints Page 9 Step 7 Closing Luminaires Pages 0- Kicker Wall Wash Orientation Finelite, Inc Whipple Road Union City, CA (50) Fax: (50) Wall of 2

2 Step - Rough-Ins & Mounting Options Mount Starter to Structure Y X = Luminaire section length (Does not include endcaps) Y = Total run length of luminaire (Includes /8" for BOTH endcaps) Z = Mounting hole location Endcap = /6" Refer to Record Drawings and building plans to determine exact mounting, suspension points, and power feed locations. Z = Mounting Hole Location (Does not include endcaps) HP-2 5" HP-4 6" Endcap X X2 X3 Starter Joiner Ender ID: ID: 2 ID: 3 Z Z Z Z Rough-In Lengths Rough-In Widths W Spackle Flange (SF) Visible Flange (VF) L Wall Wall W W L = Total Run Rough-In Length* Spackle Flange Visible Flange HP-2 & HP-4 Y + 3/4" Y + /2" * Tolerance +/- /6" Use rough-in Length & Width dimensions and Record Drawings to determine rough-in measurements. Build wall/ceiling with rough-in according to rough-in dimensions. CRITICAL: Drywall or weak paneling must be secured to blocking (studs) around rough-in opening in the wall/ceiling. W = Rough-In Width* Spackle Flange Visible Flange HP-2 3-/8" 2-7/8" HP-4 4-7/8" 4-/4" * Tolerance +/- /6" CONTINUED 2 of 2

3 Step - Rough-Ins & Mounting Options Mounting Options Option - Mount to Threaded Rod Option 2 - Mount to Structure /4" Threaded Rod Structure Support Support Blocking 2 3-/2" min. Support Blocking 2 4-/8" min. Drywall Ceiling/Wall Drywall Ceiling/Wall /4"-20 Washer /4"-20 Nut /4" Lag Bolt Luminaire mounting holes sized for /4"-20 threaded rod. Distance from threaded rod to wall/ceiling surface must be a minimum of 3-/2". Refer to Record Drawings to determine mounting hole locations on luminaires and install threaded rods to structure. Mounting Option Threaded Rod /4"-20 Washer /4"-20 Nut Mounting Option 2 /4"-20 Lag Bolt ¹ Wall/ceiling surface = drywall, wood, concrete or masonry, metal panels, tile, etc. ² Support blocking = Wooden beams/studs, sheet metal framing beams, steel beams, concrete beams, etc. Use hardware appropriate to the beam material. Distance from support block to wall/ceiling surface must be a minimum of 4-/8". Refer to Record Drawings to determine mounting hole locations on luminaires and install support blocking² to structure. 3 of 2

4 Step 2 - Identification & Preparation A. Identify Luminaires B. Remove Diffuser Diffuser Mud Guard CAUTION Arrange luminaires in order according to ID# at their install locations. Job Name Factory Order Number Unique Luminaire ID Number ID Label Luminaire Type and/or Run Length ABC Corporation - A2345 HP-4 WW-R - VF - X' STARTER HP-4 WW-R - K - 32' - S V - SC - C Full Catalog Order ID ID: Luminaire Section Type Kicker HP-4 2 Diffuser Backplate Kicker HP-2 2 Diffuser Putty Knife Identify all luminaires by their ID label that can be found on the box, on the diffuser, and inside the luminaire. NOTE: Exact location of labels in these areas may vary. Remove all luminaires from their box. Refer to Record Drawings that can be found in the hardware kit. Kitted Hardware Finelite has provided items listed here, with their Finelite part numbers. These items can be found in separate boxes shipped with the luminaire. Account for all parts and set aside until they are needed. All other hardware needed for this installation will be by others. Yoke Bracket Part# #0-32 x 5/8" Screw Part# 9444 Securing Luminaire Joints p. 9, Step 6 #8-8 x /4" Screws Part# Closing Luminaires p. 0, Step 7 #0 x /2" Screw Part# 9208 Closing Luminaires p. 0, Step 7. Push bottom edge of the diffuser into backplate. 2. Slide diffuser out of backplate. Carefully remove and set aside all diffusers to prevent from getting dirty or damaged. Ensure diffuser can be clearly identified back to its corresponding luminaire. CAUTION (Spackle Flange Only): Carefully remove Mud Guards and keep them as they will be reinstalled in Step 7C.. Slide putty knife between the backplate and diffuser. 2. Carefully separate diffuser from the backplate, keeping it inside its protective bag. Set aside all diffusers to prevent from getting dirty or damaged. Ensure diffuser can be clearly identified back to its corresponding luminaire. CAUTION (Spackle Flange Only): Carefully remove Mud Guards and keep them as they will be reinstalled in Step 7C. 4 of 2

5 Step 3 - Opening Luminaires A. Release Backplates B. Remove Backplates SIDE VIEW Backplate #8-8 x /4" Screw (provided) Backplate NOTE: If installing an independent, leave backplates installed and PROCEED TO STEP 4. Release backplates from luminaire body by removing the two #8-8 x /4" screws from both ends of the luminaire. CAUTION: Set these screws aside. Do not lose. Mounting Screw #8-8 x /4" (provided) Remove backplates by rotating then lifting up and out of the luminaire body. Keep backplate hanging with safety cables connected. 5 of 2

6 Step 4 - Mounting Starter to Structure A. Make Electrical Connections Electrical Connection Options WIRING LEGEND Black Hot Line Voltage White Neutral Line Voltage Green Ground Grey Dimming 0-0V DC Purple Dimming 0-0V DC Wire-nut electrical connections. (Typical for all options.) Conduit Splice Box Jam Nut Conduit Plate #8 Screw Conduit Plate Jam Nut Conduit Plate Starter Jam Nut While properly supporting luminaire, maneuver luminaire near wall/ceiling opening. Make electrical connections at ENDCAP, at TOP or with a SPLICE BOX. Flex Conduit #8 Screw CONDUIT PLATE - ENDCAP (Standard) Remove two screws holding conduit plate. Install conduit and jam nut onto conduit plate. Wire-nut electrical connections. See wiring legend above. Reinstall conduit plate and screws. Do not damage any wires. CONDUIT PLATE - TOP (Optional: HP-4 Only) Remove screw holding conduit plate. Install conduit and nut onto conduit plate. Wire-nut electrical connections. See wiring legend above. Reinstall conduit plate and screw. Do not damage any wires. SPLICE BOX (Optional) Lift tab to unsnap and remove splice box cover. Install conduit and nut onto splice box cover. Wire-nut electrical connections. See wiring legend above. Reinstall splice box cover. Do not damage any wires. CONTINUED 0-0V Dimming 6 of 2

7 Step 4 - Mounting Starter to Structure B. Mount Starter to Structure Option (Shown) - Mount to Threaded Rod /4"-20 Threaded Rod /4"-20 Threaded Rod Ceiling Support Blocking Support Blocking Drywall Ceiling Drywall Ceiling Option 2 - Mount to Structure Structure Support Starter /4"-20 Lag Bolt /4"-20 Washer Option (Shown) - Mount to Threaded Rod Align threaded rods with mounting holes and slide luminaire into wall/ceiling. Install /4"-20 nut and /4"-20 washer onto /4"-20 threaded rod. CRITICAL: If installing a joiner luminaire in the next step, leave the nut loose, allowing the luminaire to hang out of ceiling at an angle. If there is no joiner/ender, then tighten nuts fully. PROCEED TO STEP 7. Threaded Rod /4"-20 Nut Mounting Option /4"-20 Washer /4"-20 Nut Mounting Option 2 /4"-20 Lag Bolt Option 2 - Mount to Structure Slide luminaire into wall/ceiling and mount to structure support with hardware appropriate for the structure type. CRITICAL: If installing a joiner luminaire in the next step, leave the bolt/screw loose, allowing luminaire to hang out of ceiling at an angle. If there is no joiner/ender, then tighten nuts fully. PROCEED TO STEP 7. Support Blocking Drywall Ceiling Support Blocking Drywall Ceiling 7 of 2

8 Step 5 - Joining Luminaires A. Mount Joiner/Ender to Structure B. Join Luminaires CAUTION DO NOT attempt to join luminaires together on the floor. Damage may result when lifted. Follow these instructions. Joiner/Ender Ceiling Starter Joiner/Ender Starter While properly supporting luminaire, maneuver luminaire near wall/ceiling opening. If necessary, loosen bolts on previous luminaire so that it can hang out of the opening at an angle. After installing a joiner, return to previous luminaire and tighten. Aligner Sleeve Option (Shown) - Mount to Threaded Rod Align threaded rods with mounting holes and slide luminaire into wall/ceiling. Install /4"-20 nut and /4"-20 washer onto /4"-20 threaded rod. CRITICAL: If installing a joiner luminaire in the next step, leave the nut loose, allowing the luminaire to hang out of ceiling at an angle. If there is no joiner/ender, then tighten nuts fully. Threaded Rod Mounting Option /4"-20 Washer /4"-20 Nut Mounting Option 2 /4"-20 Lag Bolt Option 2 - Mount to Structure Slide luminaire into wall/ceiling and mount to structure support with hardware appropriate for the structure type. CRITICAL: If installing a joiner luminaire in the next step, leave the bolt/screw loose, allowing luminaire to hang out of ceiling at an angle. If there is no joiner/ender, then tighten nuts fully. Align joiner/ender with aligner sleeves on starter and slide together. Be careful not to damage any wiring. If necessary, lift both luminaires, then slide together. 8 of 2

9 Step 6 - Securing Luminaire Joints A. Secure Joint with Yoke Brackets IN ALIGNMENT CORRECTLY INSTALLED B. Make Electrical Connections Joiner/Ender Cross Section View Luminaire Joint Luminaire Joint Aligner Sleeve Starter Plug-Together Wiring Joiner/Ender Aligner Sleeve Yoke Bracket (provided) YOKE SCREW ALIGNMENT Bottom-Up View Luminaire Joint Joiner/Ender Aligner Sleeve Joiner/Ender Screwdriver with 6" bit required. Yoke Screw (provided) Before installing yoke brackets, ensure the joining ends of luminaires meet flush and square. CRITICAL: Ensure yoke brackets properly engage with aligner sleeves. Secure joint by using a screwdriver¹ to tighten yoke screws through yoke brackets and into the aligner sleeves until joint seam of luminaire is closed. Yoke Bracket w/ Screw #0-32 x 5/8" (provided) NO NOTE: Yoke screws should be installed directly across from each other, not diagonally, and in holes furthest from the joint line. One yoke screw per one yoke bracket. YES Starter Connect plug-together wiring. Universal & Robust Joints Simple Plug-Together Wiring 9 of 2

10 Step 7 - Closing Luminaires A. Replace Backplates B. Secure Joint with #0 x /2" Screw #0 x /2" Screw Backplate #8-8 x /4" Screw HP-4 Backplate HP-2 2 Joint Cover Plate #0 x /2" Screw (provided) Carefully reinstall backplate into luminaire by inserting and rotating. #0 x /2" Screw (provided) #8-8 x /4" Screws (provided) Joint Cover Plate. Carefully reinstall backplate into luminaire by inserting and rotating. 2. Install joint cover plate by inserting into backplate and installing two #8-8 x /4" screws at the joint. PROCEED TO STEP 7C WALL SIDE #8-8 x /4" Screw (provided) Install #8-8 x /4" screws to backplates. Install #0 x /2" screw. CONTINUED 0 of 2

11 Step 7 - Closing Luminaires C. Secure Flange To Structure Spackle Flange Only D. Apply Spackle Spackle Flange Only Mud Guard (provided) Ceiling Spackle Ceiling Putty Knife Wall Screw Every 6" to 2" Wall Secure flanges to wall/ceiling using appropriate screws or fasteners for hard surface, per local building codes. Install the "mud guard" cardboard inserts to help prevent spackle and paint from getting into the luminaire. Screws/Fasteners Screws or fasteners: drywall - drywall screws, wood - wood screws, etc. Mud Guard (provided) Spackle and paint over flanges up to luminaire edge. CAUTION: Careful not to drop spackle into luminaire. Immediately wipe off excess spackle that may have gotten onto luminaire edges. Perform all spackling and painting to walls and ceiling prior to removing mud guards. Remove all mud guards. CONTINUED of 2

12 Step 7 - Closing Luminaires E. Final Step - Replace Diffusers ID: 3 ID: ID: 2 ID: ID: 2 ID: 3 HP-4 HP NOTE: If your installation includes a battery backup, please see addendum (98333) that should be included with your kitting package. Remove diffusers from protective plastic bag. CAUTION: Wear gloves to keep diffuser surface clean. CRITICAL: Be sure to install correct diffuser to its corresponding luminaire ID. Install diffusers into luminaire body, ensuring they are in place.. Reinstall diffusers by pushing right side of the diffuser into the backplate. 2. Push the left side of diffuser until it's lay flat on the backplate. Turn power on to luminaire. NOTE: If your installation includes a battery backup, please see addendum (98333) that should be included with your kitting package. Remove diffusers from protective plastic bag. CAUTION: Wear gloves to keep diffuser surface clean. CRITICAL: Be sure to install correct diffuser to its corresponding luminaire ID. Install diffusers into luminaire body, ensuring they are in place.. Slide the side of the diffuser without a notch into the luminaire. 2. Push the side of the diffuser that has a notch until click sound is heard. Turn power on to luminaire. 2 of 2