Important for Ottoman and other gas lift beds

Transcription

1

2 Important for Ottoman and other gas lift beds Note: The bed base is in the upright position when first assembled as the gas lifts are fully extended during shipment for safety. After assembly a firm downward push will be required to overcome any resisitance in the gas lifts as these may initially stick. We suggest placing a mattress on top of the bed base to aide this and also test the operation of your new lift up bed by lifting and pushing down the bed base a few times to allow the lfting mechanism to bed in. The lift mechanism provides assistance with the lift of the mattress fitted to the base. It does not lift the mattress for you. The system has been designed to effectively lift the base system fitted with a variety of mattress weights and combinations of depths. Depending on the combination of the mattress weight and depth determines the degree of assistance provided by the mechanism. Following the installation of the mechanism lift, pull the base up and down a few times to free off the system. The gas cylinders fitted to the system may be stiff when first used or if the system has not been operated for a period of time. Use the strap handles to lift up the mattress base using two hands. Pull the mattress base down using two hands equally spaced from the centre of the mattress base. DO NOT pull down on one side of the base only as this is likely to damage the base system with potential failure of the mattress base system and lift mechanism. Do NOT operate the lift up mechanism without the mattress placed on the base. Caution: Do NOT allow children to operate the lift mechanism. Do NOT allow children near the lift base when operating the mechanism. Do NOT allow children in the area of the internal storage base. Keep hands clear of the mechanism when operating the base system. Do NOT stand inside the bed or the internal storage base. Do NOT overload the internal storage base.

3 Pafts List Pafts Description Box Qty Headboard Frame 2 Left Wooden Post Right Wooden Post 4 Footboard Left Side Rail 6 Right Side Rail 7 Centre Storage Panel B Back Storage Panel 2/', 2..ts 4,a ' 4 2 I I 2 2. t 9 Small Base Panel 0 Large Base Panel f I l. Slat., ' 28 t2 Left Hydraulic BaseSupport with stopper I I Right Hydraulic Base Support, T4 Hydraulic Pump 2 Back Bed Base I I 6 Front Bed Base, Page 2 of 9

4 Hardware List (Found in box #) Pafts Description Box Qty,, A Mini Fix ' L2 \@ B B x 0 mm Wooden Dowel 6 C D Metal Corner Block M6x 90 mm Barrel 2 ' 4 E MB x 2 mm JCBC Bolt w., 6 F G H MB x mm JCBC Bolt AP MB x 20 mm JCBC Bolt ar MBX 7 mm JCBC Bolt I MB Flat Washer I J K Base Nut Base Handle I ' B 0,,, 4 4 4,., 2 L M N M6x 40 mm ICBC Bolt MB x 4 mm Bolt with Hex Nut, Spring & @ Single Slat Cap 4 6.., 28 o P a R Double Slat Cap Wooden Button N \Jy M6 Allen Key MB Allen Key S M 2.8 Spanner T M4 Spanner xx You will also need a screwdriver and small mallet ( not provided ). L4 4. ' Page of 9

5 Step : Attach the headboard frame () and back storage panel (B) to the left wooden post (2) and right wooden post (), Secure the headboard frame using hardware paftsb, D and P, then secure theback storage panel with hardware pafts A and B, DO NOT use any power tools as this may damage the frame and willinvalidate any claim. Step 2: Join together the left side rail () and right side rail (6) withthe centre storage panels (7) using hardware pafts A and B, DO NOT use any power tools as this may damage the frame and willinvalidate any claim, Page 4 of 9

6 Step : Attach the headboard frame () and footboard (4) usinghardware part E, DO NOT use any power tools as this maydamage the frame andwill invalidate any claim. Step 4: Attach hardware p;rr-t C usrng hardware parts F. DO NOT use any power tools asthis may damage the frame and will invalidate any claim, Page of 9

7 Step : Attach the hydraulic pumps (4) to the left hydraulic base suppoft (2) and right hydraulic base support () then fix the base supports to the side rails using hardware part G as shown in Fig.2 - do not fully tighten yet. Inserthe remainder of hardware part G and fully tighten all bolts. DO NOT use any power tools as this may damage the frame and lvill ir,rvalidate any claim. Hydraulic Pump right installation. Step 6: loin together the back bed base () and front bedbase (6) using hardware pafts H, I and l. Attach hardware parts K using hardware part L. DO NOT use any power tools as this may damage the frameand will invalidate any claim. Page 6 of 9

8 Step 7: Insefthe slats () to ha rdwa re parrtsn and O then press into the base making sure they are secure. DO NOT use any power tools asthis maydar ma age the frame and will invalidate anv claim. II+ Step 8: Insefthe small base panel (9) and large base panels (0). DO NOT use any power tools as thismay damage the frame and willinvalidate any claim, -' Step 9: Attach the bed base to and finishing in area - the hydraulic frames using hardwarepart M. Fix the bolts starting from area do notfully tighten the bolts yet, DO NOT use any power tools asthis may damage the frame and willinvalidate any claim. \.-- u) Page 7 of 9

9 Step l0: Adjusthe bed base making sure that the distance to the footboard is approximately 0 - mm. Tlghten all bolts and screws now. DO NOT use any power tools as this may damage the frame and will invalidate any claim. Page 8 of 9

10 CAUTION : PLEASE USE HYDRAULIC PUMP STOPPER FOR SAFETY PURPOSE HYDRAULIC PUMP STOPPER (LOCK OUT) Page 9 of 9

11 IMPORTANT NOTE II WI-IEN THE BED IS BUILT AND THE MATTRESS FRAME IS AT 4 DEGREE PLEASE PLACE THE MATTRESS ON THE BED. PLEASE NOTE THAT THE WEIGHT OF THE MATTRESS IS REQUIRED TO HELP CLOSE THE BED TO LOWER THE SLEEPING PLATFORM STAND AT THE FOOT END OF THE BED AND PUSH SHARPLY DOWNWARDS USING BOTH HANDS.

12 Please dispose of all packaging safely. General Care & Maintenance Wipe clean with a slightly damp cloth. Avoid the use of all household cleaners and abrasives. Periodically check all screw & fixings to ensure they are secure. When moving your product, carefully lift into place. Never drag or push the pieces across the floor as this will cause damage to the joints and could result in failure to the product that will invalidate the warranty. For more information on cleaning and product care visit: Notes We ve tried to make this product as easy to assemble as possible. In the unlikely event that you have problems putting it together or have damaged or missing pieces, please contact us by visiting: