Metal Film Fixed Resistor
|
|
|
- Susanna Potter
- 5 years ago
- Views:
Transcription
1 Specifications: Type : MCMF Rated Power : 0.25W at 70 C Max. Working Voltage : 250V Max. Overload Voltage : 500V Dielectric Withstanding Voltage : 500V Rated Ambient Temp : 70 C Operating Temp. Range : -55 C to +155 C Resistance Tolerance MCMF0W4B Series : ±0.1% MCMF0W4F Series : ±1% Resistance Range Power Rating: : 10Ω to 1MΩ Resistors shall have a power rating based on continuous full load operation at an ambient temperature of 70 C. For temperature in excess of 70 C, the load shall be derated as shown in the below figure. Voltage Rating: Resistors shall have a rated direct-current (DC) continuous working voltage or an approximate sine-wave root-mean-square (RMS) alternating-current (AC) continuous working voltage at commercialline frequency and waveform curresponding to the power rating, as determined from the following formula : RCWV = P R Were : RCWV = Rated DC or RMS AC continuous working voltage at commercial-line frequency and waveform (V) P = Power Rating (W) R = Nominal Resistance (Ω) In no case shall the rated DC or RMS AC continuous working voltage be greater than the applicable maximum value. Page <1> 10/07/15 V1.1
2 Construction No Name Material 1 Basic Body Rod Type Ceramics 2 Resistance Film Metal Film 3 End Cap Steel (Tin plated iron surface) 4 Lead Wire Annealed copper wire coated with tin 5 Joint By Welding 6 Coating Insulated epoxy resin ( Colour : Sky Blue ) 7 Colour Code Epoxy Resin Metal Film Fixed Resistors Characteristics Limits Test Methods( JIS C ) DC. resistance Insulation resistance Dielectric withstanding voltage Temperature coefficient Short time overload Terminal strength Solderability Must be within the specified tolerance Insulation resistance is 10,000MΩ Min. No evidence of flashover mechanical damage, arcing or insulation break down Within the temperature coefficient specified below :± 50 PPM/ C Max. ± (0.5% Ω) Max. with no evidence of mechanical damage No evidence of mechanical damage 95 % coverage Min. The limit of error of measuring apparatus shall not exceed allowable range or 1% of resistance tolerance Resistors shall be clamped in the trough of a 90 metallic V-block or foil method use a metal foil shall be wrapped closely around the body of the resistor. After that shall be tested at DC potential respectively specified in the above list for /-0 secs. Resistors shall be clamped in the trough of a 90 metallic V-block or foil method use a metal foil shall be wrapped closely around the body of the resistor. After that shall be tested at AC potential respectively specified in the table 1. for /-0 secs. Natural resistance change per temp. degree centigrade R2-R1 R1(t2-t1) 10 6 (PPM/ C) R1: Resistance value at room temperature (t1) R2: Resistance value at room temp. plus 100 C (t2) Permanent resistance change after the application of a potential of 2.5 times RCWV for 5 seconds Direct load: Resistance to a 2.5 kgs direct load for 10secs. in the direction of the longitudinal axis of the terminal leads Twist test : Terminal leads shall be bent through 90 at a point of about 6mm from the body of the resistor and shall be rotated through 360 about the original axis of the bent terminal in alternating direction for a total of 3 rotations The area covered with a new, smooth,clean, shiny and continuous surface free from concentrated pinholes. Test temp. of solder : 245 C ± 3 C Dwell time in solder : 2 ~ 3 seconds Page <2> 10/07/15 V1.1
3 Metal Film Fixed Resistors Characteristics Limits Test Methods( JIS C ) Soldering temp. reference Resistance to soldering heat Electrical characteristics shall be satisfied. Without distinct deformation in appearance.(95 % coverage Min.) ± (1% Ω) Max. with no evidence of mechanical damage The leads immersed into solder bath to 3.2 to 4.8 mm. from the body. Permanent resistance change shall be checked. Wave soldering condition: (2 cycles Max.) Pre-heat : 100 ~ 120 C, 30 ± 5 sec. Suggestion solder temp.: 235 ~ 255 C, 10 sec. (Max.) Peak temp.: 260 C Hand soldering condition: Hand Soldering bit temp. : 380 ± 10 C Dwell time in solder : 3 +1/-0 sec. Permanent resistance change when leads immersed to 3.2 to 4.8 mm from the body in 350 C ± 10 C solder for 3 ± 0.5 seconds Resistance change after continuous5 cycles for duty shown below: Temperature cycling Vibration Load life in humidity Load life ± (1% Ω) Max. with no evidence of mechanical damage ± (1% Ω) Max. Step Temperature Time 1-55 C ± 3 C 30 mins 2 Room temp. 10 ~ 15 mins C ± 2 C 30 mins 4 Room temp. 10 ~ 15 mins 55Hz, 3 planes 2hrs each Total amplitude = 1.5mm Resistance value Δ R/R Resistance change after 1,000 hours (1.5 hours on, 0.5 hour off ) at RCWV in Normal type ± 1.5 % a humidity test chamber controlled at 40 C ± 2 C and 90 to 95 % relative humidity Resistance value Δ R/R 7.1 Permanent resistance change after1,000 hours operating at RCWV with duty cycle of Normal type ± 1.5 % (1.5 hours on, 0.5 hour off ) at70 C ± 2 C ambient Resistance to solvent No deterioration of protective coatings and markings Specimens shall be immersed in a bath of trichroethane completely for 3 minutes with ultrasonic Pulse overload ± (1% Ω) Max. with no evidence of mechanical damage Resistance change after 10,000 cycles (1 sec. on, 25 secs. off ) at 4 times RCWV Page <3> 10/07/15 V1.1
4 Dimension Type Power Rating D (Max.) L (Max.) d ± 0.05 H ± 3 MCMF 1/4W 2.5mm 6.8mm 0.54mm 28mm Painting method Welding point, terminal and lead wire, is permissible to be exposed without the outer coated cover. The extent should be within 1/2 of the are angle. Marking 1. Resistor Resistors shall be marked with colour coding colours shall be in accordance with JIS C 0802 Table 2. Label Label shall be marked with following items: 1. Type and style 2. Nominal resistance 3. Resistance tolerance 4. Quantity 5. Lot number 6. PPM 1kΩ Metal Film Fixed Resistor MCMF0W4BB1001A5 10Ω Metal Film Fixed Resistor MCMF0W4FF100JA50 10kΩ Metal Film Fixed Resistor MCMF0W4BB1002A kΩ Metal Film Fixed Resistor MCMF0W4FF1022A50 100kΩ Metal Film Fixed Resistor MCMF0W4BB1003A kΩ Metal Film Fixed Resistor MCMF0W4FF1051A50 20kΩ Metal Film Fixed Resistor MCMF0W4BB2002A kΩ Metal Film Fixed Resistor MCMF0W4FF1071A50 250Ω Metal Film Fixed Resistor MCMF0W4BB2500A50 110Ω Metal Film Fixed Resistor MCMF0W4FF1100A50 5kΩ Metal Film Fixed Resistor MCMF0W4BB5001A50 1.1kΩ Metal Film Fixed Resistor MCMF0W4FF1101A50 50Ω Metal Film Fixed Resistor MCMF0W4BB500JA50 11kΩ Metal Film Fixed Resistor MCMF0W4FF1102A50 100Ω Metal Film Fixed Resistor MCMF0W4FF1000A50 110kΩ Metal Film Fixed Resistor MCMF0W4FF1103A50 1kΩ Metal Film Fixed Resistor MCMF0W4FF1001A50 11Ω Metal Film Fixed Resistor MCMF0W4FF110JA50 10kΩ Metal Film Fixed Resistor MCMF0W4FF1002A50 113kΩ Metal Film Fixed Resistor MCMF0W4FF1133A50 100kΩ Metal Film Fixed Resistor MCMF0W4FF1003A kΩ Metal Film Fixed Resistor MCMF0W4FF1152A50 1MΩ Metal Film Fixed Resistor MCMF0W4FF1004A50 120Ω Metal Film Fixed Resistor MCMF0W4FF1200A50 Page <4> 10/07/15 V1.1
5 1.2kΩ Metal Film Fixed Resistor 12kΩ Metal Film Fixed Resistor 120kΩ Metal Film Fixed Resistor 12Ω Metal Film Fixed Resistor 121Ω Metal Film Fixed Resistor 1.21kΩ Metal Film Fixed Resistor 12.1kΩ Metal Film Fixed Resistor 1.24kΩ Metal Film Fixed Resistor 130Ω Metal Film Fixed Resistor 1.3kΩ Metal Film Fixed Resistor 130kΩ Metal Film Fixed Resistor 13Ω Metal Film Fixed Resistor 13.3kΩ Metal Film Fixed Resistor 14Ω Metal Film Fixed Resistor 14.7kΩ Metal Film Fixed Resistor 150Ω Metal Film Fixed Resistor 1.5kΩ Metal Film Fixed Resistor 15kΩ Metal Film Fixed Resistor 150kΩ Metal Film Fixed Resistor 15Ω Metal Film Fixed Resistor 160Ω Metal Film Fixed Resistor 1.6kΩ Metal Film Fixed Resistor 16kΩ Metal Film Fixed Resistor 16Ω Metal Film Fixed Resistor 1.62kΩ Metal Film Fixed Resistor 174Ω Metal Film Fixed Resistor 1.74kΩ Metal Film Fixed Resistor 174kΩ Metal Film Fixed Resistor 178Ω Metal Film Fixed Resistor 180Ω Metal Film Fixed Resistor 1.8kΩ Metal Film Fixed Resistor 18kΩ Metal Film Fixed Resistor 180kΩ Metal Film Fixed Resistor 18Ω Metal Film Fixed Resistor 182Ω Metal Film Fixed Resistor 1.82kΩ Metal Film Fixed Resistor 196Ω Metal Film Fixed Resistor 196kΩ Metal Film Fixed Resistor 200Ω Metal Film Fixed Resistor MCMF0W4FF1201A50 MCMF0W4FF1202A50 MCMF0W4FF1203A50 MCMF0W4FF120JA50 MCMF0W4FF1210A50 MCMF0W4FF1211A50 MCMF0W4FF1212A50 MCMF0W4FF1241A50 MCMF0W4FF1300A50 MCMF0W4FF1301A50 MCMF0W4FF1303A50 MCMF0W4FF130JA50 MCMF0W4FF1332A50 MCMF0W4FF140JA50 MCMF0W4FF1472A50 MCMF0W4FF1500A50 MCMF0W4FF1501A50 MCMF0W4FF1502A50 MCMF0W4FF1503A50 MCMF0W4FF150JA50 MCMF0W4FF1600A50 MCMF0W4FF1601A50 MCMF0W4FF1602A50 MCMF0W4FF160JA50 MCMF0W4FF1621A50 MCMF0W4FF1740A50 MCMF0W4FF1741A50 MCMF0W4FF1743A50 MCMF0W4FF1780A50 MCMF0W4FF1800A50 MCMF0W4FF1801A50 MCMF0W4FF1802A50 MCMF0W4FF1803A50 MCMF0W4FF180JA50 MCMF0W4FF1820A50 MCMF0W4FF1821A50 MCMF0W4FF1960A50 MCMF0W4FF1963A50 MCMF0W4FF2000A50 2kΩ Metal Film Fixed Resistor MCMF0W4FF2001A50 20kΩ Metal Film Fixed Resistor MCMF0W4FF2002A50 200kΩ Metal Film Fixed Resistor MCMF0W4FF2003A50 20Ω Metal Film Fixed Resistor MCMF0W4FF200JA kΩ Metal Film Fixed Resistor MCMF0W4FF2052A50 205kΩ Metal Film Fixed Resistor MCMF0W4FF2053A50 2.1kΩ Metal Film Fixed Resistor MCMF0W4FF2101A50 210kΩ Metal Film Fixed Resistor MCMF0W4FF2103A50 215kΩ Metal Film Fixed Resistor MCMF0W4FF2153A50 220Ω Metal Film Fixed Resistor MCMF0W4FF2200A50 2.2kΩ Metal Film Fixed Resistor MCMF0W4FF2201A50 22kΩ Metal Film Fixed Resistor MCMF0W4FF2202A50 220kΩ Metal Film Fixed Resistor MCMF0W4FF2203A50 22Ω Metal Film Fixed Resistor MCMF0W4FF220JA kΩ Metal Film Fixed Resistor MCMF0W4FF2211A50 226kΩ Metal Film Fixed Resistor MCMF0W4FF2263A50 237Ω Metal Film Fixed Resistor MCMF0W4FF2370A50 240Ω Metal Film Fixed Resistor MCMF0W4FF2400A50 2.4kΩ Metal Film Fixed Resistor MCMF0W4FF2401A50 24kΩ Metal Film Fixed Resistor MCMF0W4FF2402A50 240kΩ Metal Film Fixed Resistor MCMF0W4FF2403A50 24Ω Metal Film Fixed Resistor MCMF0W4FF240JA50 249Ω Metal Film Fixed Resistor MCMF0W4FF2490A kΩ Metal Film Fixed Resistor MCMF0W4FF2491A kΩ Metal Film Fixed Resistor MCMF0W4FF2492A50 249kΩ Metal Film Fixed Resistor MCMF0W4FF2493A Ω Metal Film Fixed Resistor MCMF0W4FF249JA50 261kΩ Metal Film Fixed Resistor MCMF0W4FF2613A50 270Ω Metal Film Fixed Resistor MCMF0W4FF2700A50 2.7kΩ Metal Film Fixed Resistor MCMF0W4FF2701A50 27kΩ Metal Film Fixed Resistor MCMF0W4FF2702A50 270kΩ Metal Film Fixed Resistor MCMF0W4FF2703A50 27Ω Metal Film Fixed Resistor MCMF0W4FF270JA50 274Ω Metal Film Fixed Resistor MCMF0W4FF2740A kΩ Metal Film Fixed Resistor MCMF0W4FF2741A kΩ Metal Film Fixed Resistor MCMF0W4FF2742A kΩ Metal Film Fixed Resistor MCMF0W4FF2872A50 294Ω Metal Film Fixed Resistor MCMF0W4FF2940A50 294kΩ Metal Film Fixed Resistor MCMF0W4FF2943A50 Page <5> 10/07/15 V1.1
6 29.4Ω Metal Film Fixed Resistor MCMF0W4FF294JA50 300Ω Metal Film Fixed Resistor MCMF0W4FF3000A50 3kΩ Metal Film Fixed Resistor MCMF0W4FF3001A50 30kΩ Metal Film Fixed Resistor MCMF0W4FF3002A50 300kΩ Metal Film Fixed Resistor MCMF0W4FF3003A50 30Ω Metal Film Fixed Resistor MCMF0W4FF300JA50 301Ω Metal Film Fixed Resistor MCMF0W4FF3010A kΩ Metal Film Fixed Resistor MCMF0W4FF3011A kΩ Metal Film Fixed Resistor MCMF0W4FF3012A50 301kΩ Metal Film Fixed Resistor MCMF0W4FF3013A kΩ Metal Film Fixed Resistor MCMF0W4FF3091A50 309kΩ Metal Film Fixed Resistor MCMF0W4FF3093A50 324kΩ Metal Film Fixed Resistor MCMF0W4FF3243A50 330Ω Metal Film Fixed Resistor MCMF0W4FF3300A50 3.3kΩ Metal Film Fixed Resistor MCMF0W4FF3301A50 33kΩ Metal Film Fixed Resistor MCMF0W4FF3302A50 330kΩ Metal Film Fixed Resistor MCMF0W4FF3303A50 33Ω Metal Film Fixed Resistor MCMF0W4FF330JA kΩ Metal Film Fixed Resistor MCMF0W4FF3321A kΩ Metal Film Fixed Resistor MCMF0W4FF3322A Ω Metal Film Fixed Resistor MCMF0W4FF332JA kΩ Metal Film Fixed Resistor MCMF0W4FF3572A50 360Ω Metal Film Fixed Resistor MCMF0W4FF3600A50 36kΩ Metal Film Fixed Resistor MCMF0W4FF3602A50 36Ω Metal Film Fixed Resistor MCMF0W4FF360JA kΩ Metal Film Fixed Resistor MCMF0W4FF3651A kΩ Metal Film Fixed Resistor MCMF0W4FF3652A50 365kΩ Metal Film Fixed Resistor MCMF0W4FF3653A50 374Ω Metal Film Fixed Resistor MCMF0W4FF3740A50 374kΩ Metal Film Fixed Resistor MCMF0W4FF3743A Ω Metal Film Fixed Resistor MCMF0W4FF374JA50 383Ω Metal Film Fixed Resistor MCMF0W4FF3830A Ω Metal Film Fixed Resistor MCMF0W4FF383JA50 390Ω Metal Film Fixed Resistor MCMF0W4FF3900A50 3.9kΩ Metal Film Fixed Resistor MCMF0W4FF3901A50 39kΩ Metal Film Fixed Resistor MCMF0W4FF3902A50 390kΩ Metal Film Fixed Resistor MCMF0W4FF3903A50 39Ω Metal Film Fixed Resistor MCMF0W4FF390JA50 392Ω Metal Film Fixed Resistor MCMF0W4FF3920A kΩ Metal Film Fixed Resistor 39.2kΩ Metal Film Fixed Resistor MCMF0W4FF3921A50 MCMF0W4FF3922A Ω Metal Film Fixed Resistor MCMF0W4FF392JA50 402Ω Metal Film Fixed Resistor 40.2kΩ Metal Film Fixed Resistor 402kΩ Metal Film Fixed Resistor MCMF0W4FF4020A50 MCMF0W4FF4022A50 MCMF0W4FF4023A Ω Metal Film Fixed Resistor MCMF0W4FF402JA kΩ Metal Film Fixed Resistor 430Ω Metal Film Fixed Resistor 4.3kΩ Metal Film Fixed Resistor 430kΩ Metal Film Fixed Resistor 43Ω Metal Film Fixed Resistor 4.32kΩ Metal Film Fixed Resistor 43.2kΩ Metal Film Fixed Resistor 4.42kΩ Metal Film Fixed Resistor 4.53kΩ Metal Film Fixed Resistor 464Ω Metal Film Fixed Resistor 4.64kΩ Metal Film Fixed Resistor 470Ω Metal Film Fixed Resistor 4.7kΩ Metal Film Fixed Resistor 47kΩ Metal Film Fixed Resistor 470kΩ Metal Film Fixed Resistor 47Ω Metal Film Fixed Resistor 475Ω Metal Film Fixed Resistor 4.75kΩ Metal Film Fixed Resistor 47.5kΩ Metal Film Fixed Resistor 475kΩ Metal Film Fixed Resistor MCMF0W4FF4221A50 MCMF0W4FF4300A50 MCMF0W4FF4301A50 MCMF0W4FF4303A50 MCMF0W4FF430JA50 MCMF0W4FF4321A50 MCMF0W4FF4322A50 MCMF0W4FF4421A50 MCMF0W4FF4531A50 MCMF0W4FF4640A50 MCMF0W4FF4641A50 MCMF0W4FF4700A50 MCMF0W4FF4701A50 MCMF0W4FF4702A50 MCMF0W4FF4703A50 MCMF0W4FF470JA50 MCMF0W4FF4750A50 MCMF0W4FF4751A50 MCMF0W4FF4752A50 MCMF0W4FF4753A Ω Metal Film Fixed Resistor MCMF0W4FF475JA kΩ Metal Film Fixed Resistor 499Ω Metal Film Fixed Resistor 4.99kΩ Metal Film Fixed Resistor 49.9kΩ Metal Film Fixed Resistor 499kΩ Metal Film Fixed Resistor MCMF0W4FF4871A50 MCMF0W4FF4990A50 MCMF0W4FF4991A50 MCMF0W4FF4992A50 MCMF0W4FF4993A Ω Metal Film Fixed Resistor MCMF0W4FF499JA50 510Ω Metal Film Fixed Resistor 5.1kΩ Metal Film Fixed Resistor 51kΩ Metal Film Fixed Resistor 510kΩ Metal Film Fixed Resistor 51Ω Metal Film Fixed Resistor MCMF0W4FF5100A50 MCMF0W4FF5101A50 MCMF0W4FF5102A50 MCMF0W4FF5103A50 MCMF0W4FF510JA50 Page <6> 10/07/15 V1.1
7 5.11kΩ Metal Film Fixed Resistor MCMF0W4FF5111A50 511kΩ Metal Film Fixed Resistor MCMF0W4FF5113A Ω Metal Film Fixed Resistor MCMF0W4FF511JA50 523kΩ Metal Film Fixed Resistor MCMF0W4FF5233A Ω Metal Film Fixed Resistor MCMF0W4FF523JA kΩ Metal Film Fixed Resistor MCMF0W4FF5361A50 560Ω Metal Film Fixed Resistor MCMF0W4FF5600A50 5.6kΩ Metal Film Fixed Resistor MCMF0W4FF5601A50 56kΩ Metal Film Fixed Resistor MCMF0W4FF5602A50 560kΩ Metal Film Fixed Resistor MCMF0W4FF5603A50 56Ω Metal Film Fixed Resistor MCMF0W4FF560JA kΩ Metal Film Fixed Resistor MCMF0W4FF5621A kΩ Metal Film Fixed Resistor MCMF0W4FF5622A50 5.9kΩ Metal Film Fixed Resistor MCMF0W4FF5901A50 604Ω Metal Film Fixed Resistor MCMF0W4FF6040A kΩ Metal Film Fixed Resistor MCMF0W4FF6041A kΩ Metal Film Fixed Resistor MCMF0W4FF6042A50 604kΩ Metal Film Fixed Resistor MCMF0W4FF6043A kΩ Metal Film Fixed Resistor MCMF0W4FF6191A kΩ Metal Film Fixed Resistor MCMF0W4FF6192A50 619kΩ Metal Film Fixed Resistor MCMF0W4FF6193A50 620Ω Metal Film Fixed Resistor MCMF0W4FF6200A50 6.2kΩ Metal Film Fixed Resistor MCMF0W4FF6201A50 62kΩ Metal Film Fixed Resistor MCMF0W4FF6202A50 620kΩ Metal Film Fixed Resistor MCMF0W4FF6203A50 62Ω Metal Film Fixed Resistor MCMF0W4FF620JA50 649Ω Metal Film Fixed Resistor MCMF0W4FF6490A kΩ Metal Film Fixed Resistor MCMF0W4FF6491A Ω Metal Film Fixed Resistor MCMF0W4FF665JA50 680Ω Metal Film Fixed Resistor MCMF0W4FF6800A50 6.8kΩ Metal Film Fixed Resistor MCMF0W4FF6801A50 68kΩ Metal Film Fixed Resistor MCMF0W4FF6802A50 680kΩ Metal Film Fixed Resistor MCMF0W4FF6803A50 68Ω Metal Film Fixed Resistor MCMF0W4FF680JA50 681Ω Metal Film Fixed Resistor 6.81kΩ Metal Film Fixed Resistor MCMF0W4FF6810A50 MCMF0W4FF6811A Ω Metal Film Fixed Resistor MCMF0W4FF681JA kΩ Metal Film Fixed Resistor 750Ω Metal Film Fixed Resistor 7.5kΩ Metal Film Fixed Resistor 75kΩ Metal Film Fixed Resistor 750kΩ Metal Film Fixed Resistor 75Ω Metal Film Fixed Resistor 768kΩ Metal Film Fixed Resistor MCMF0W4FF7151A50 MCMF0W4FF7500A50 MCMF0W4FF7501A50 MCMF0W4FF7502A50 MCMF0W4FF7503A50 MCMF0W4FF750JA50 MCMF0W4FF7683A Ω Metal Film Fixed Resistor MCMF0W4FF768JA50 806Ω Metal Film Fixed Resistor 820Ω Metal Film Fixed Resistor 8.2kΩ Metal Film Fixed Resistor 82kΩ Metal Film Fixed Resistor 820kΩ Metal Film Fixed Resistor 82Ω Metal Film Fixed Resistor 825Ω Metal Film Fixed Resistor 8.25kΩ Metal Film Fixed Resistor 82.5kΩ Metal Film Fixed Resistor 845Ω Metal Film Fixed Resistor 8.45kΩ Metal Film Fixed Resistor 8.66kΩ Metal Film Fixed Resistor 909Ω Metal Film Fixed Resistor 9.09kΩ Metal Film Fixed Resistor 90.9kΩ Metal Film Fixed Resistor MCMF0W4FF8060A50 MCMF0W4FF8200A50 MCMF0W4FF8201A50 MCMF0W4FF8202A50 MCMF0W4FF8203A50 MCMF0W4FF820JA50 MCMF0W4FF8250A50 MCMF0W4FF8251A50 MCMF0W4FF8252A50 MCMF0W4FF8450A50 MCMF0W4FF8451A50 MCMF0W4FF8661A50 MCMF0W4FF9090A50 MCMF0W4FF9091A50 MCMF0W4FF9092A Ω Metal Film Fixed Resistor MCMF0W4FF909JA50 910Ω Metal Film Fixed Resistor MCMF0W4FF9100A50 9.1kΩ Metal Film Fixed Resistor MCMF0W4FF9101A50 91kΩ Metal Film Fixed Resistor MCMF0W4FF9102A50 91Ω Metal Film Fixed Resistor MCMF0W4FF910JA kΩ Metal Film Fixed Resistor MCMF0W4FF9311A50 953Ω Metal Film Fixed Resistor MCMF0W4FF9530A kΩ Metal Film Fixed Resistor MCMF0W4FF9761A50 Important Notice : This data sheet and its contents (the Information ) belong to the members of the Premier Farnell group of companies (the Group ) or are licensed to it. No licence is granted for the use of it other than for information purposes in connection with the products to which it relates. No licence of any intellectual property rights is granted. The Information is subject to change without notice and replaces all data sheets previously supplied. The Information supplied is believed to be accurate but the Group assumes no responsibility for its accuracy or completeness, any error in or omission from it or for any use made of it. Users of this data sheet should check for themselves the Information and the suitability of the products for their purpose and not make any assumptions based on information included or omitted. Liability for loss or damage resulting from any reliance on the Information or use of it (including liability resulting from negligence or where the Group was aware of the possibility of such loss or damage arising) is excluded. This will not operate to limit or restrict the Group s liability for death or personal injury resulting from its negligence. Multicomp is the registered trademark of the Group. Premier Farnell plc Page <7> 10/07/15 V1.1
Metal Film Resistor Kit
Ratings: Rated Power 0.5W at 70 C Max. Working Voltage 350V Max. Overload Voltage 700V Dielectric Withstanding Voltage 700V Rated Ambient Temp. 70 C Operating Temp. Range -55 C to +155 C Resistance Tolerance
Metal Film Resistor Kit
Ratings: Rated Power 0.25W at 70 C Max. Working Voltage 250V Max. Overload Voltage 500V Dielectric Withstanding Voltage 500V Rated Ambient Temp. 70 C Operating Temp. Range -55 C to +155 C Resistance Tolerance
Power Metal Fixed Resistors
Type Designation: (EX.) The type designation shall be in the following form: Type Power Rating Resistance Tolerance Nominal Resistance MCPMR 1W-SSS < 1 Ω : 0.6 W 1 Ω : 1 W J 0.56 Ω 1 Ω Ratings: Ratings
Carbon Film Fixed Resistor
Features Automatically insertable High quality performance Non-Flame type available Cost effective and commonly used Too low or too high values can be supplied on case to case basis Performance Specification
Surface Mount Resistor Kit 0603 Case Size
Specifications Table Type Power Rating Resistance Tolerance Nominal Resistance MC 0603 0.0625W (1/16W) ±1% 10Ω Ratings: Type MC 0603 Power Rating 0.0625W (1/16W) Max. Working Voltage 50V Max. Overload
Surface Mount Resistor Kit 0603 Case Size
Specifications Table Type Power Rating Resistance Tolerance Nominal Resistance MC 0603 0.0625W (1/16W) ±5% 10Ω Ratings: Type MC 0603 Power Rating 0.0625W (1/16W) Rated Current(Jumper) 1A Max. Overload
Carbon Composition Resistor
Rating and Dimensions Dimensions : Millimetres Power Dimensions L D Lead d Maximum Rated Maximum Overload Dielectric Withstand Tolerance ±(%) R-Value 1/4 W 6.4 ±0.7 2.3 ±0.2 0.6 250 400 500 5 E-24 1/2
Uniroyal Electronics Industry Company Limited
1.0 Scope: This specification for approve relates to Lead-Free Metal Film Fixed Resistors manufactured by UNIOHM S specification. 2.0 Ratings & Dimension: 2.1 Normal size: Type D Max. Dimension(mm) L d
High Precision Thin Film Chip Resistor
Description: The resistors are constructed in a high grade ceramic body (aluminium oxide). Internal metal electrodes are added at each end and connected by a resistive paste that is applied to the top
SOLITRONICS ENGINEERING LTD. TEL: (852) FAX: (852)
RESISTOR SPECIFICATIONS Date: 19 th June 1997 RoHS COMPLIANT CARBON FILM FIXED RESISTOR SEL-RGD-1001(1) 1. FEATURES High quality at competitive prices Meet JIS-C-5202 & USA MIL-R-22684B specifications
SPECIFICATION FOR APPROVAL. Approved by
SPECIFICATION FOR APPROVAL TRELIK Description : Cement Fixed Resistors Royalohm Part no.: PRW0AWJxxxxB00 (PRW 10W +/-5%) Approved by Parts corresponding to RoHS Compliant: 2005-Apr.-1 Royal Electronic
Pulse Withstanding Chip Resistors
Construction 1 Alumina Substrate Features: Tolerance from ±0.5% to 5%. High power rating. Excellent pulse withstanding performance. Improved working voltage ratings. Standard package sizes of 0805 to 2512.
PRODUCT SPECIFICATION
PRODUCT SPECIFICATION Description: CRGH Series Product Type: (Resistance range: 1.0Ω ~ 10MΩ) CRGH0603_XXX (CRGH0603 1/5W +/- 1% & 5% Taped) CRGH0805_XXX (CRGH0805 1/3W +/- 1% & 5% Taped) CRGH1206_XXX (CRGH1206
PRODUCT SPECIFICATION
PRODUCT SPECIFICATION Description: CRGH Series Product Type: (Resistance range: 1.0Ω ~ 10MΩ) CRGH0603_XXX (CRGH0603 1/5W +/- 1% & 5% Taped) CRGH0805_XXX (CRGH0805 1/3W +/- 1% & 5% Taped) CRGH1206_XXX (CRGH1206
Chip Resistors Pulse Withstanding
Features: Tolerance from ±0.5% to 5% High power rating Excellent pulse withstanding performance Improved working voltage ratings Standard package sizes of 0603 to 2512 Applications: Metering (Testing/Measurement)
DATA SHEET. 88 Longteng Road, Economic & Technical Development Zone, Kunshan, Jiangsu, China
DATA SHEET Product Name Fusible Resistors Part Name FRN Series Uniroyal Electronics Global Co., Ltd. 88 Longteng Road, Economic & Technical Development Zone, Kunshan, Jiangsu, China Tel +86 512 5763 1411
1. INSTRUCTION: THIS SHEET IS THE STATEMENT OF THE LEAD-FREE THICK FILM CHIP RESISTORS SPECIFICATION THAT UNIOHMS PRODUCTIONS CAN MEET.
PART NO.: CHIP RESISTORS FILE NO.: CX-01-001 1. INSTRUCTION: THIS SHEET IS THE STATEMENT OF THE LEAD-FREE THICK FILM CHIP RESISTORS SPECIFICATION THAT UNIOHMS PRODUCTIONS CAN MEET. 2. RATING: TYPE 0402
Rotary Series. Specifications. Material. Soldering Process. Max Room Temperature 120 ~ 150sec 60sec. 5 ~ 10sec.
Specifications Mechanical Mechanical Life Operating Force Environmental Operating Temperature Storage Temperature : 200mΩ max. 20,000 steps : 200gf-cm max. : -25 C to +80 C : -40 C to +85 C Material Base
DATA SHEET. Product Name Wire-wound Anti-Surge Fixed Resistors Part Name KNPA Series
DATA SHEET Product Name Wire-wound Anti-Surge Fixed Resistors Part Name KNPA Series Uniroyal Electronics Global Co., Ltd. 88 Longteng Road, Economic & Technical Development Zone, Kunshan, Jiangsu, China
Type EP Series. Wirewound Anti-Surge Resistor. Key Features. Characteristics Electrical. Power Derating Curve
Key Features n Power up to 10W in Small Size n 16 Size / Power Options n Specially Designed and Tested for Surge Immunity n Flame Resistant Coating TE Connectivity is pleased to offer this wire wound axial
Thick Film Chip Resistor
Features: Small size and light weight. Highly reliable multilayer electrode construction. Compatible with all soldering process. Construction 1 Alumina Substrate 2 Bottom Electrode (Ag-Pd) 3 Top Electrode
Ceramic Disc Capacitors, X7R
Mechanical Available lead code: (unit : mm) Lead type P/N Digits (F) Lead Length (L) Available Rated Voltage Packing Lead Configuration Lead Style : B Straight Long Lead B20C7 7.5 ± 1 20 Min. 1 KV, 2 KV
Metal Oxide Varistors
Straight Lead Dimensions Table Series 5D 7D 10D 14D 20D D max 7 9.5 14 17.5 24 d* 0.6 0.6 0.8 0.8 1 W** 5 5 7.5 7.5 10 H max 12.5 14.5 20 22.5 29.5 H1 max 10 12 17 20.5 28 T max 4.9 4.9 8.5 8.5 9 P max
Rotary Series. Specifications. Material. Soldering Process. Max Room Temperature 120 ~ 150sec 60sec. 5 ~ 10sec.
MCRH2 MCRV2 MCRS2 Specifications Mechanical Mechanical Life : 200mΩ max. 20,000 steps Operating Force : 200gf-cm max. Environmental Operating Temperature : -25 C to +80 C Storage Temperature : -40 C to
Contents. Introduction Page. 1.0 Scope Ratings & Dimension...4~ Structure Marking... 5~ Derating Curve...
Contents Introduction Page 1.0 Scope...4 2.0 Ratings & Dimension....4~5 3.0 Structure.....5 4.0 Marking..... 5~7 5.0 Derating Curve...7~8 6.0 Performance Specification...8~9 7.0 Explanation of Part No.
Large Snap-In Electrolytic Capacitors HPR Series
Features: Highly reliable capacitors that has characteristics of high temperature 105ºC, and can withstand high ripple current Suitable for filter of industrial equipment, such as automatic machines, computers
Type CRG Series THICK FILM CHIP RESISTORS. Electrical Characteristics. Power rating: Key Features
Key Features Type CRG Series Thick Film Resistors with high power to size ratio, ideally suited to industrial and general purpose use Value range from Ω to MΩ Eight package sizes Terminal finish matte
Sales: Technical: Fax:
DATA SHEET Metal film resistors 62-0712 n/a PACK 100 10R 0.25W MF RESISTOR (RC) 62-0714 n/a PACK 100 12R 0.25W MF RESISTOR (RC) 62-0715 n/a PACK 100 13R 0.25W MF RESISTOR (RC) 62-0717 n/a PACK 100 15R
CONTENTS 1.0 SCOPE RATINGS & DIMENSION STRUCTURE MARKING... 4~6 5.0 POWER RATING PERFORMANCE SPECIFICATION...
CONTENTS 1.0 SCOPE...3 2.0 RATINGS & DIMENSION......3 3.0 STRUCTURE..4 4.0 MARKING..... 4~6 5.0 POWER RATING...6 6.0 PERFORMANCE SPECIFICATION...6~7 7.0 EXPLANATION OF PART NO. SYSTEM...8~9 8.0 ORDERING
Contents. Introduction Page. 1.0 Scope Ratings & Dimension...4~ Structure Marking... 6~ Derating Curve...
Contents Introduction Page 1.0 Scope...4 2.0 Ratings & Dimension....4~5 3.0 Structure...5 4.0 Marking... 6~8 5.0 Derating Curve...8 6.0 Performance Specification...9~10 7.0 Explanation of Part No. System
RND Components Thick Film SMD Resistors
RND Components Thick Film SMD Resistors Resistor Assortments, SMD, E24, RND RND 1550402WGFE024KIT in size 0402 1% tolerance RND 1550402WGJE024KIT in size 0402 5% tolerance RND 1550603SAFE024KIT in size
Pushbutton Switches. Sub-Miniature. Specifications: Switch Function. Page <1> 08/10/11 V1.1. : Dependent upon content material
Specifications: Contact rating : Dependent upon content material Mechanical life : 50,000 make-and-break cycles Maximum contact resistance : 20 mω initial at 2-4 V dc 100 ma for both silver and gold plated
Rocker and Paddle Switches
R2 Specifications: Contact rating : 5 A with resistant load at 120 V ac or 28 V dc 2 A with resistant load at 250 V ac Mechanical life : 50,000 make-and-break cycles Maximum contact resistance : 10 mω
Wire Wound Chip Inductor
Features Ceramic base provide high Ultra-compact inductors provide high Q factors ow profile, high current options Miniature SMD chip inductor for fully automated assembly Outstanding endurance from Pull-up
SPECIFICATION FOR APPROVAL 1/8W 0816 LOW RESISTNACE CHIP RESISTOR
PAGE : 1 OF 11 1/8W 0816 LOW RESISTNACE CHIP RESISTOR 1. Scope This specification applies to 0.8mm x 1.60mm size 1/8W, fixed metal film chip resistors rectangular type for use in electronic equipment.
MELF Coated Thin Film Precision Resistors (MELFC Series)
Features: Precision TCR of 0, 5, 25 & 50ppm/ C High reliability and stability of ±0. and ±0.5% Excellent pulse load capability Strong mechanical body due to cylindrical shape AEC-Q200 compliant RoHS and
Description: Lead-Free Thick Film Chip Resistors
C O N F I D E N T I A L D O C U M E N T SPECIFICATION FOR APPROVAL 冠發 Description: Lead-Free Thick Film Chip Resistors Royalohm Part no: Chip Series ±0.5%, ±1%, ±2%, ±5% & 0Ω Approved by Ticrom Technology
ULTRA LOW POWER SMD METAL STRIP RESISTORS
Features These specification covers 2512 sized high power low resistance current sensing metal resistors. PART NUMBERING SYSTEM: - 2512 A 1W R005 F E C Type Dimensions Code 2512 Construction Resistance
High Power 6W LED. Package Dimensions: Features: Applications: Absolute Maximum Ratings at Ta=25 C.
Package Dimensions: Features: Excellent transiting heat from LED chip operating under 350mA High luminous output No UV Applications: Reading lights Portable flashlight Uplighters & downlighters Garden
TC25 High Precision Thin Film chip resistors Size 1206, 0805, 0603, 0402 (Anti-Sulfuration )
SF2U, SF08U, SF06U, SF04U ±.0%, ±0.5%, 0.25%, ±0.%, ±0.05% TC25 High Precision Thin Film chip resistors Size 206, 0805, 0603, 0402 (Anti-Sulfuration ) *Contents in this sheet are subject to change without
TC25 High Precision Power Thin Film chip resistors Size 0805, 0603
WF08R, WF06R ±0.5%, ±0.25%, ±0.1% TC25 High Precision Power Thin Film chip resistors Size 0805, 0603 Customer : Approval No : Issue Date : Customer Approval : Page 1 of 9 WFxxR Jan.-2010 Ver.3 FEATURE
Sub-Miniature Cable. Specifications: Page <1> 05/04/12 V1.1
: Sub-miniature cable, 7-1-2C, to Def Stan 61-12 (Part 4) : 0.055 mm 2 (7/0.1 mm) tinned annealed copper wires to BS 6360 (as far as applicable), class 5 : Number of wires = 7 : Maximum resistance at 20
!"#$ % &"#$ ,-././ / 0. / / 1 1/ 1 ' !"%!" "&6 7-- (8$&8+. '(')*+,-+-#+.'
!"#$ % &"#$ '()*'( +!"#$,-,-././ / 0. / / 1 1/ 1 '!"%!"234534 "&6 7-- (8$&8+. "$ "$* '(')*+,-+-#+.' /'**0'(* !"!# $ % &'!!"!# $ % &'! ()#"* +!"!# $, $! "# $ $ %& !"!#$% # %&"!%'' %&%( )"%*! +,- %.&% ".%'
SPECIFICATION FOR APPROVAL. 1/2W, 0603, Low Resistance Chip Resistor (Lead / Halogen free)
PAGE : 1 OF 7 1/2W, 0603, Low Resistance Chip Resistor (Lead / Halogen free) 1. Scope This specification applies to 0.8mm x 1.6mm size 1/2W, fixed metal film chip resistors rectangular type for use in
High Power 6W LED. Package Dimensions: Features: Applications: Absolute Maximum Ratings at Ta=25 C.
Package Dimensions: Features: Excellent transiting heat from LED chip operating under 350mA High luminous output No UV Applications: Reading lights Portable flashlight Uplighters & downlighters Garden
SPECIFICATION FOR APPROVAL. 1/8W, 0402, Low Resistance Chip Resistor (Lead / Halogen Free)
DOCUMENT REVISION : SRK220000NH : A2 SPECIFICATION FOR APPROVAL PAGE : 1 OF 9 1/8W, 0402, Low Resistance Chip Resistor (Lead / Halogen Free) 1. Scope This specification applies to1.0mm x 0.5mm size 1/8W,
WF12T, WF08T, WF06T, WF04T 0.5%, 0.1% TC50 High Precision Thin Film chip resistors Size 1206, 0805, 0603, 0402
SPECIFICATION OF HIGH PRECISION THIN FILM CHIP RESISTOR Ver: Page: of 8 ROHS compliance WF2T, WF08T, WF06T, WF04T 0.5%, 0.% TC50 High Precision Thin Film chip resistors Size 206, 0805, 0603, 0402 SPECIFICATION
Thick Film Chip Resistors. ( Lead Free for RM series standard ) page 1/13
( Lead Free for RM series standard ) page 1/13 1. Scope : This specification applies for the RM series of thick film chip resistors made by. 2. Construction: Over Coat Conductor : (Lead-free or with lead
RALEC 旺詮. Scope: 2 (EX) request. IE-SP /01/05. Released Date Page No. Remark. Series. Resistance Tolerance. Nominal Resistance.
RTH High Power Thick Film Chip Document No. Released Date Page No. IE-SP-030 2018/01/05 1 1 Scope: 1.1 This specification is applicable to lead-free and halogen-free RTH series high power thick film chip
Terminal Blocks. TBF Turrett Terminal Series. Specifications: Material: Page <1> 17/01/12 V1.1
s TBF Turrett Terminal Series Insulator : PBT, rated UL94V-0 : 300 V ac : 15 A : 500 MΩ : 22-14 AWG : -65 C to +125 C Dimensions : (Millimetres) Unless Otherwise Specified All Dimensions are (mm) A = 0.374
Low Resistance Flat Chip Resistors Type SR73
Low Resistance Flat Chip Resistors Type SR73 1. Scope This specification applies to chip resistors (SR73) produced by KOA Corporation. CERTIFIED AHA 9/29/11 CERTIFIED 2. Type Designation The type designation
Data sheet FIXED THICK FILM CHIP RESISTORS; RECTANGULAR TYPE & ANTI-SULFURATION. AEC-Q200 qualified. RoHS COMPLIANCE ITEM Halogen and Antimony Free
No.: RMAW K HTS-0001 /5 Date: 2017. 4. 21 Data sheet : ANTI-SULFURATION RMAW10,16,20,32 AEC-Q200 qualified RoHS COMPLIANCE ITEM Halogen and Antimony Free Note: Stock conditions Temperature: +5 C +35 C
HRS2 Series PCB Relays
Features: Low profile. Fully sealed. Standard and sensitive coil versions. DPCO contacts. Specifications: Coil Data: Nominal Voltage : 3V dc to 24V dc. Nominal Power Consumption : 150 to 360mW. Contact
WF12K, WF08K, WF06K, WF04K ±1.0%, 0.5%, ±0.25%, ±0.1% High Precision Thick Film chip resistors
WF2K, WF08K, WF06K, WF04K ±.0%, 0.5%, ±0.25%, ±0.% TC50 High Precision Thick Film chip resistors Size 206, 0805, 0603, 0402 Page of 8 WFxxK_V02 Jan.200 FEATURE. SMD Thick film resistor 2. High reliability
Approval Sheet. for. Metal Oxide Film Resistors. RSF series ±5% YAGEO CORPORATION
Approval Sheet for Metal Oxide Film Resistors RSF series ±5% YAGEO CORPORATION Headquarters: 3F, No.233-1, Pao Chiao Rd., Shin Tien, Taipei, Taiwan, R.O.C. Tel: 886-2-2917-7555 Fax: 886-2-2917-4286 URL:
SPECIFICATION FOR APPROVAL. 1/32W, Low Resistance Chip Resistor (Lead / Halogen free)
PAGE : 1 OF 7 1/32W, 01005 Low Resistance Chip Resistor (Lead / Halogen free) 1. Scope This specification applies 0.2mm x 0.4mm (01005) size 1/32W, fixed metal film chip resistors rectangular type for
BDW93C, BDW94C Series
Features Designed for general-purpose amplifier and low speed switching applications Collector-emitter sustaining voltage- CEO (sus) = (Minimum) Collector-emitter saturation voltage- CE (sat) = 2 (Maximum)
Metal Film Precision Resistor. Features
Features -Excellent overall stability -Tight tolerance down to ±0.1% -Extremely low TCR down to ±10 PPM/ C -High power rating up to 1 Watts Applications -Telecommunication -Medical Equipment Construction
Thick Film Chip Resistor Arrays Thick Film Chip Resistor Networks (Lead-Free for CN Series Standard)
page number 1 /12 1. Scope : This specification applies for the CN series of thick film chip resistor arrays & chip resistor networks made by MQEC. 2. Construction, Dimensions, Schematic : 2.1 Construction
Metal Film Precision Resistor. Features
Features -Excellent overall stability -Tight tolerance down to ±0.1% -Extremely low TCR down to ±10 PPM/ C -High power rating up to 1 Watts Applications -Telecommunication -Medical Equipment Construction
HVR. Lead Wire Length (H, mm)
High Resistor Features Special conductive film withstands high voltage d L H D working voltage far over that of generalpurpose resistors Suitable for applications such as TV s, high voltage power supply,
Thick Film Chip Resistor Arrays Thick Film Chip Resistor Networks. (Lead-Free for CN34 Series) page 1/10
(Lead-Free for CN34 Series) page 1/10 1. Scope : This specification applies for the CN34 series of thick film chip resistor arrays made by TA-I. 2. Construction, Dimensions, Schematic : 2.1 Construction
SMD MELF - Resistors. Metal Film Precision Resistor - SMDM Series Size: 0204/ official distributor of
Product : Metal Film Precision Resistor - SMDM Series Size: 0204/ 0207 official distributor of Metal Film Precision Resistor (SMDM Series) 1. Features -Excellent overall stability -Tight tolerance down
Selection Series: E24 & E96 E24 & E96 Temp. Coefficient (ppm/ C):
Thin Film Precision Resistors 1206 1210 Rated Power @ 70 C: 0.125W 0.2W Resistance Range (Ohms) Min: 4R7 4R7 4R7 1R0 4R7 1R0 4R7 4R7 4R7 1R0 4R7 1R0 Max: 1M0 2M5 1M0 2M5 1M0 2M5 1M0 2M5 1M0 2M5 1M0 2M5
Precision Thin Film Precision Resistors
Key Features Thin film precision resistors with TC's of 15ppm, 25ppm and 50ppm and tolerances to 0.1%. Applications in measurement, telemetry and for sensing circuits. Case sizes 0402, 0603, 0805, 1206,
High Voltage Thick Film Chip Resistors Product Specification
Page No 1/10 1 Scope: 11 This specification is applicable to lead and halogen free for RTV series thick film chip resistors 12 Lead free products mean lead free termination meets RoHS requirement Pb contained
Z LEAD SURFACE MOUNT SPECIFICATION AC AXIAL CEMENTED WIREWOUND RESISTOR & PR POWER METAL FILM RESISTORS
Z LEAD SURFACE MOUNT SPECIFICATION AC AXIAL CEMENTED WIREWOUND RESISTOR & PR POWER METAL FILM RESISTORS FEATURES Surface mounted version Low cost alternative for SMD molded resistor High power dissipation
TM-533-T/R TACT Switches
Features: Sharp click feel with a positive tactile feed-back. Due to small movement distance (stroke), user experiences distinct sensation when the switch clicks into place. Ultraminiature and light weight
SMD - Resistors. Pulse Withstanding Thick Film Chip Resistor-SMDP Series. Product: Size: 0603/0805/1206/1210/2010/2512. official distributor of
Product: Pulse Withstanding Thick Film Chip Resistor-SMDP Series Size: 0603///12// official distributor of 1. Scope Pulse Withstanding Thick Film Chip Resistor-SMDP Series -This specification applies to
P600 Series 6A Power Diodes
Standard Axial Rectifiers Features: High surge current capability. Void-free plastic in a P600 package. High current operation 6.0 Amperes at T A = 55 C. Exceeds environmental standards of MIL-S-19500/228.
Ultraminiature Rocker&Lever Switches V ac or dc
Specifications: Contact Rating Mechanical Life Contact Resistance Minimum Insulation Resistance Dielectric Strength Operating Temperature Materials: Case and Bushing Switch Support Contacts/Terminals :
BZW04 Series. Features: DO-41. Mechanical Data. Page <1> 14/05/08 V1.1
DO-41 Features: Plastic package. Exceeds environmental standards of MIL-STD-19500. 400W surge capability at 10 x 1000µs waveform, duty cycle: 0.01%. Excellent clamping capability. Low impedancesurge resistance.
RMC10,16,20,32,35,50,63 Automotive Grade Page: 1/10
+5 C +35 C 75% Product specification contained in this data sheet are subject to change at any time without notice If you have any questions or a Purchasing Specification for any quality Agreement is necessary,
DATA SHEET GENERAL PURPOSE CHIP RESISTORS RC1218 (Pb Free) 5%; 1% Product specification Oct 13, 2004 V.1
DATA SHEET GENERAL PURPOSE CHIP RESISTORS 5%; 1% 2 SCOPE This specification describes 1218 series chip resistors with lead-free terminations made by thick film process. ORDERING INFORMATION Part number
DATA SHEET ARRAY CHIP RESISTORS YC324 (8Pin/4R; Pb Free) 5%, 1% sizes Product specification Feb 22, 2005 V.1 Supersedes Date of Mar.
3 DATA SHEET ARRAY CHIP RESISTORS 324 (Pin/4R; Pb Free) 5%, 1% sizes 1220 Product specification Supersedes Date of Mar. 06, 2003 Product specification 2 SCOPE This specification describes 324 series chip
Surge Withstanding Thick FilmResistors(SWCR Series)
Surge Withstanding Thick FilmResistors(SWCR Series) Features: Excellent surge and pulse withstanding performance Higher power rating than General Purpose Thick Film Resistors Offered in to sizes RoHS &
Thick Film Resistor Networks Military, MIL-PRF Qualified, Type RZ Dual-In-Line Package, 01, 03, 05 Schematics
FEATURES MIL-PRF-83401 qualified Epoxy molded construction All device leads are hot-solder dipped Available in tube pack TCR available in "K" (± 100 ppm/ C) or "M" (± 300 ppm/ C) depending on style 100
SPECIFICATIONS. Metal Film Precision Resistor. CSR-Serie SWISSDIS. Swissdis AG Grasweg 7 CH-4911 Schwarzhäusern
SWISSDIS Swissdis AG Grasweg 7 CH-4911 Schwarzhäusern Tel.: +41 62 919 44 00 Fax: +41 62 919 44 01 info@swissdis.ch www.swissdis.ch SPECIFICATIONS CSR-Serie Version June 2017 Features -Excellent overall
Type CPF Series. Thin Film Precision Resistors. Key Features
Type CPF Series Key Features Thin film precision resistors with TC's to 15ppm and tolerances to 0.05%. Wide range of case sizes from 0201 to 2512 Suitable for all applications where close accuracy and
DATA SHEET FUSIBLE CHIP RESISTORS FR series (Pb Free) 5% sizes 0603/1206. Product specification Sep 26, 2005 V.0
DATA SHEET FUSIBLE CHIP RESISTORS series (Pb Free) 5% sizes 0603/1206 2 Chip Resistor Surface Mount SCOPE This specification describes 0603/1206 fusible chip resistors with leadfree terminations made by
Darlington Transistor TO-3
Description Designed for use as output devices in complementary general purpose amplifier applications. Features: High gain darlington performance High DC current gain hfe = 1,000 (Minimum) at Ic = 20A
FrelTec GmbH. Current Sensing Chip Resistor SMD
GmbH Mathildenstr. 10A 82319 Starnberg Germany SMD 6/8/2015 1/13 Freltec GmbH www.freltec.com SPECIFICATION Part Number 017 05 * R001 * J * T05 ** D E Size Value Tolerance Packing TCR Power Rating 017
Thick Film Resistor Networks, Dual-In-Line, Molded DIP
STANDARD ELECTRICAL SPECIFICATIONS POWER RATING / ELEMENT (1) RANGE NO. OF P 70 C PINS Ω W MDP 14 MDP 16 01 05 01 05 0.2 0.2 Consult factory Consult factory Notes (1) For resistor power ratings at + 25
Thick Film Resistor Networks, Military, MIL-PRF Qualified, Type RZ010 and RZ020 Dual-In-Line, Molded DIP
MDM (Military M831/1 and /2) Thick Film Resistor Networks, Military, MIL-PRF-831 Qualified, Type RZ1 and RZ2 Dual-In-Line, Molded DIP STANDARD ELECTRICAL SPECIFICATIONS VISHAY DALE MODEL/ PIN NO. MIL STYLE
Type RN73 Series. Thin Film Precision Resistors. Electrical Characteristics. Key Features. Applications
Type RN73 Series Key Features High precision - TCR 5ppm/ C and 10ppm/ C Tolerance down to 0.01% Thin film (nichrome) Terminal finish electroplated 100% matte Sn Applications Communications Industrial Controls
High Precision Thin Film chip resistors (RoHS compliant Halogen Free) Size 2512, 2010, 1210, 1206, 0805, 0603, 0402, 0201
WF25U,WF20U,WF0U,WF2U,WF08U, WF06U,WF04U, WF02U ±%, ±0.5%, ±0.25%, ±0.%, ±0.05%, ±0.0% TC25 High Precision Thin Film chip resistors (RoHS compliant Halogen Free) Size 252, 200, 20, 206, 0805, 0603, 0402,
Tri-Rated Flexible PVC Equipment Wire
Application: High temperature, flame retardant wire designed for use in the switch control, relay and instrumentation panels of power switchgear and for purposes such as internal connectors in rectifier
Darlington Transistors
Features: Designed for general-purpose amplifier and low speed switching applications Collector-emitter sustaining voltage - V CEO (sus) = 60 V (minimum) - TIP120, TIP125 80 V (minimum) - TIP121, TIP126
FrelTec GmbH. Thin Film Chip Resistor SMD High Precision (1% to 0,01%) Low TCR (2 to 50 ppm) and Thin Film current sensing
GmbH Mathildenstr. 0A 89 Starnberg Germany Thin Film Chip Resistor SMD High Precision (% to 0,0%) Low TCR ( to 50 ppm) and Thin Film current sensing 5/7/05 / GmbH www.freltec.com SPECIFICATION Part Number
SMD Power Inductors. Features: Applications: Figure 1. Figure 2. Page <1> 20/06/11 V1.1
Features: Ferrite based SMD inductor with lower core loss. Ideal for LCD driver, DSC/DVC, Notebook PC or High density board design. Operating temperature range -55 C to + 130 C. MCSDRH73B - Series High
SMD CHIP RESISTOR. How To Order: RC 0603 J 2K3 B 10. Tolerance: Size: Pcs/reel Chip. Resistance: Series: Size of B=0.1% 1R=1 ohm.
SMD CHIP RESISTOR How To Order: Series: RC Part No.: RC 0603 J 2K3 B 10 Series: Size: Tolerance: Resistance: Size of Pcs/reel Chip 0201 B=0.1% 1R=1 ohm Reel 10=10k/reel Resistor 0402 D=0.5% 2.3R=2R3 B=13
Sales: Technical: Fax:
DATA SHEET Metal film resistors Order code Manufacturer code Description 64-0725 2322 157 15609 PACK 1000 56R 0.4W MF RESISTOR (RC) 64-0475 n/a PACK 100 390R 0.4W MF RESISTOR 64-0480 n/a PACK 100 470R
FUSIBLE RESISTOR - NFR25H
FUSIBLE RESISTOR - FEATURES Metal film technology Suitable for protection of circuit boards and designs Overload protection without risk of fire Defined interruption behavior (fusing time) Wide range of
This specification applies for the RMS series of Anti-Sulfurated thick film chip resistors made by TA-I. RMS 10 J T 103.
page number 1/13 1. Scope : This specification applies for the RMS series of Anti-Sulfurated thick film chip resistors made by TA-I. 2. Construction: Over Coat (Color : Black) Conductor Sn Plating Ceramic
Thin Film Precision Chip Resistor (AR Series)
Construction D1 L (AR Series) Features -Advanced thin film technology -Very tight tolerance down to ±0.01% -Extremely low TCR down to PPM/ C -Wide resistance range 1ohm ~ 3Mega ohm -Miniature size 0201
Pulse Withstanding Thick Film Resistors(PWCR Series)
Pulse Withstanding Thick Film Resistors(PWCR Series) Features: Excellent pulse withstanding performance Higher power ratings than General Purpose Thick Film Resistors Improved working voltage ratings Offered
TIP120, 121, 122, 125, 126, 127
Features: Collector - emitter sustaining voltage - V CEO (sus) = 60 V (minimum) - TIP120, TIP125 80 V (minimum) - TIP121, TIP126 100 V (minimum) - TIP122, TIP127 Collector - emitter saturation voltage
Over Coat. Resistive Element RBS 10 B T P Product Code Size Tolerance Packaging TCR Nominal. e.g., (1608) 1/10W.
page 1/10 1. Scope : This specification applies for the RBS series of chip resistors made by TA-I. 2. Construction: Over Coat Sn Plating Ni Plating Resistive Element Ceramic Substrate Inner electrode 3.
SPECIFICATIONS. Metal Film Precision Resistor. CSRV-Serie SWISSDIS. Swissdis AG Grasweg 7 CH-4911 Schwarzhäusern
SWISSDIS Swissdis AG Grasweg 7 CH-4911 Schwarzhäusern Tel.: +41 62 919 44 00 Fax: +41 62 919 44 01 info@swissdis.ch www.swissdis.ch SPECIFICATIONS Metal Film Precision Resistor CSRV-Serie Version August
A S J ASJ PTE LTD LEAD FREE THIN FILM CHIP RESISTOR SPECIFICATION. Reference No. : SYS-ENG-209. Revision No. : D
ASJ PTE LTD LEAD FREE THIN FILM CHIP Reference No. : SYS-ENG-209 Revision No. : D DOC NO: SYS-ENG-209 PAGE: 2 of 24 1.0 SCOPE...... 3 2.0 PART NUMBERING SYSTEM...... 3 3.0 RATING....... 3 3.1 Rated Power......