INSTALLATION & MAINTENANCE INSTRUCTIONS ON THE PCR-5 4 CHANNEL REMOTE CONTROL SYSTEM

Size: px

Start display at page:

Download "INSTALLATION & MAINTENANCE INSTRUCTIONS ON THE PCR-5 4 CHANNEL REMOTE CONTROL SYSTEM"

Dorthy Elliott
5 years ago
Views:

1 TM TM LIGHTING INSTALLATI & MAINTENANCE INSTRUCTIS THE PCR-5 4 CHANNEL REMOTE CTROL SYSTEM FEATURES Easy to Install Approved to U563 & CSA C22.2 No Pending Remote Control Operation from PCT-5 Transmitter Optional Local Control from BR-04 Module Optional Wi-Fi Control from Apple ios Devices or Android Devices Wet Location Construction PENDING BELLS ELECTRIC PTY LTD 1/3 CAPTAIN COOK DRIVE CARINGBAH NSW 2229 PHE: (02) P.O. BOX 2966 TAREN POINT NSW 2229 FAX: (02)

INSTALLATI INSTRUCTIS FOR PCR-5 4 CHANNEL REMOTE CTROL SYSTEM The PCR-5 4 Channel Remote Control System only works as a system with the PCR-4 or

As shown in the illustration below the system is controlled by TOUCH from the PCT-5 Transmitter or by optional Wi-Fi Control from Android or Apple

) = 0.7A/115VAC, 0.3A/240VAC OUTPUT VOLTAGE = 12V D/C OUTPUT POWER = 50 WATTS APPROVED TO IEC/AS/NZS 61347 NO.

POWER 1 2 3 4 REMOTE CTROL MODULE BTR-4 Optional BR-04 Local Control Module 4 CHANNEL REMOTE CTROL 4 Loads such as Pumps, Blowers, Heater, Valve

2 INSTALLATI INSTRUCTIS FOR PCR-5 4 CHANNEL REMOTE CTROL SYSTEM The PCR-5 4 Channel Remote Control System only works as a system with the PCR-4 or PCR-200 PAL Colour Touch Drivers. As shown in the illustration below the system is controlled by TOUCH from the PCT-5 Transmitter or by optional Wi-Fi Control from Android or Apple Smart Phones and Tablets. TM Channel 5 PCR-4 CLASS 2 POWER SUPPLY FOR PAL 4 WIRE LIGHTS SUPPLY VOLTAGE = V (47-63 Hz) SUPPLY CURRENT (TYP.) = 0.7A/115VAC, 0.3A/240VAC OUTPUT VOLTAGE = 12V D/C OUTPUT POWER = 50 WATTS APPROVED TO IEC/AS/NZS NO. TUV15577EA & UL 8750 Suitable for Wet Locations RECEIVER/DRIVER DRIVER 4ZD6 E o Tc :50 C PAL Pool Lighting PAL Mini Channel 1-4 PAL Optics POWER REMOTE CTROL MODULE BTR-4 Optional BR-04 Local Control Module 4 CHANNEL REMOTE CTROL 4 Loads such as Pumps, Blowers, Heater, Valve Control To control the PCR-5 Remote Control Unit by Wi-Fi the PCR-4 or PCR-200 must be fitted with the PAL Touch-5 Wi-Fi Module (Part No. 42-PCTWF5) The PCR-5 can be fitted with the BR-04 module to provide local control with Indication. This module can also be hardwired to provide remote control with indication. Page 2

3 IMPORTANT INFORMATI The PCR-5 must be installed in accordance with the National Electrical Code by a Certified Electrician or Qualified Pool Technician. INSTALLATI INSTRUCTIS FOR PCR-5 RGB OUTDOOR CTROLLER Step 1. The PCR-5 Enclosure must be located a minimum distance of 5 feet measured horizontally from the inside wall of the pool and not less than 1 foot above the maximum pool water level measured to the top of the PCR-5 Enclosure. NOTE: The enclosure must be mounted using the mounting feet on the enclosure with the 4x 6# x 3/4 long 316 grade stainless steel screw set supplied. If the enclosure is to be mounted on a concrete or block wall: Mark out the mounting hole locations and drill 3/16 holes using a masonry drill then fit the Star Plugs supplied into the holes and fix using the stainless steel screws supplied. Step 2. Using the conduit entry in top right hand side of the PCR-5 (as shown) connect the V power supply to the NEC code requirements. Step 3. Using the conduit entries at the bottom of the PCR-5 (as shown) to connect the switch wires to the Power Relays. Step 4. The PCR-5 Driver / Receiver is factory set to operate with the PCT-5 Transmitter supplied. Just fit the 2 x batteries supplied with the PCT-5 and the Transmitter is coded ready to provide Touch control to the system. Please refer to the information supplied with the PCT-5 transmitter for full operating instructions and features of the system. Step 5. To operate any of the four channels from the PCT-5 transmitter just simply press the from the selected channel to start and by pressing OFF to turn off. 2 SPEED SELECTI CHANNEL 4 Channel 4 can control 2 Speed Pumps if wired as shown on Page 5. If the button is pressed on Channel 4 once the motor will start in HIGH Speed. To select LOW speed press the button twice and after 3 minutes to allow the pump to prime in HIGH speed the power relays will change over to LOW speed. NB: If the motor is run for longer than 3 minutes in HIGH speed by pressing the button on Channel 4 it will change the power relays to LOW speed. Page 3

INSTALLATI INSTRUCTIS FOR PCR-5 RGB OUTDOOR CTROLLER Power On Note:

AC/12V DC & DRIVER/RECEIVER E A N EARTH ACTIVE NEUTRAL 1/2" PVC

FZ3 All PCR-5 drivers are supplied with 1x PCT-5 Hand Held

4 INSTALLATI INSTRUCTIS FOR PCR-5 RGB OUTDOOR CTROLLER Power On Note: Use the 4x Mounting Feet to fasten the enclosure to the wall with the screw set supplied. 1/2 PVC Conduit Adaptor Code Setting ELECTRIC POWER SUPPLY AC/12V DC & DRIVER/RECEIVER E A N EARTH ACTIVE NEUTRAL 1/2" PVC Conduit To Power Supply 4A R4 FZ4 V- CH4 AUX FZ2 Speed Low Speed High FZ3 All PCR-5 drivers are supplied with 1x PCT-5 Hand Held Transmitter & Wall Holder R1 R2 R3 FZ1 4CH-PCT 5U 1/2 PVC Conduit Adaptor Connect Loads to Power Relays as shown on Page 5 Page 4

5 CABLE CNECTI DETAILS FOR CHANNEL 1, 2 & 3 CH1 CH2 CH3 R1 R2 R3 FROM SUPPLY N/L2 N/L2 FROM SUPPLY N/L2 FROM SUPPLY N/L2 TO CH1 LOAD N/L2 TO CH2 LOAD N/L2 TO CH3 LOAD CABLE CNECTI DETAILS FOR CHANNEL 4 FOR 120V 2 SPEED MOTOR CH4 R4 N/C N/O Speed Low Speed High CH4A 120V 2 SPEED MOTOR N CABLE CNECTI DETAILS FOR CHANNEL 4 FOR 240V 2 SPEED MOTOR CH4 R4 N/C N/O Speed Low Speed High L2 240V 2 SPEED MOTOR Page 5

Turn the minute hand clockwise until 11:00 AM is aligned with the triangle on the inner dial. The hour and the minute dial will show exactly 11:00.

6 TIMER INSTRUCTIS TIME SETTING To set the current time turn the minute Hand clockwise. Do not set the time by Rotating the outer dial. Turn the minute hand clockwise until the time of day on the outer dial is aligned with the triangle marker on the inner dial (two o clock position). Example for 24-hour program dial 11:00 AM. Turn the minute hand clockwise until 11:00 AM is aligned with the triangle on the inner dial. The hour and the minute dial will show exactly 11:00. The 24-Hour dial has quarter-hour divisions and AM/PM indications. The time switch is programmed by pushing the captive trippers to the outer ring position for the entire period that the load is to be turned, i.e., fifteen minutes for each tripper on the 24-Hour dial. When the tripper is pushed to the inside, the switch is in the OFF position. TABS IN TO SET OFF OPERATI OPERATI With the Time Clock programmed and set in Automatic Mode The time clock will switch and OFF Channel 4 controlling the pump. With the Time Clock OFF Channel 4 can be switched & OFF from the PCT-3 Transmitter. With the Time Clock The PCT-3 Transmitter cannot switch OFF Channel 4. NOTE: If the Channel 4 button on the PCT-3 Transmitter is pressed when the Time Clock is channel 4 will stay after the time clock switches OFF until channel 4 is turned OFF by the PCT-3 Transmitter. TABS OUT TO SET OPERATI Page 6

7 DIMENSIAL DETAILS 7 1/8 / 181.0mm 6 7/8 / 174.0mm 13/16 / 21.0mm Knockout to connect power supply All PCR-5 remotes are supplied with 1x PCT-5 Hand Held Transmitter & Wall Holder 9 1/8 / 232.0mm 8 7/8 / 225.0mm 13/16 / 21.0mm Knockout is fitted on the bottom of both sides of the enclosure 3 9/16 / 90.0mm 2 5/16 / 75.0mm 5/8 / 15.0mm 13/16 / 21.0mm Knock Out Drill Location Points 6 7/8 / 174.0mm Knockout Instructions It is recommended that the cover is fitted and the cover screws tight when the knockouts are being removed. When removing the knock outs place a flat blade screwdriver with a 3/16 (4mm) blade as shown and a light hit with a hammer to the head of the screw driver will allow the Knockout to be removed. Alternatively drill location points are located in the centre of each Knock out to allow the use of a hole saw to remove the knockouts. Publication No. P42-13AU Page 7

ELECTRONIC ROTARY GEAR MOTOR SERIES SED (AR2...SE )

ELECTRONIC ROTARY GEAR MOTOR SERIES SED (AR2...SE ) ELECTRIC ROTARY GEAR MOTOR SERIES SED (AR2...SE ) INSTALLATI AND OPERATING INSTRUCTIS 1 GENERAL FEATURES 2 2 TECHNICAL DATA 3 3 INSTALLATI 3 ELECTRIC CNECTIS 5 CALIBRATI 5 5.1 ENDSWITCHES 5 5.2 AUXILIARY