RadioStar INTRODUCTION

Size: px

Start display at page:

Download "RadioStar INTRODUCTION"

Beatrice Skinner
5 years ago
Views:

1 CONTENTS INTRODUCTION...2 PACK CONTENTS...2 SAFETY INSTRUCTIONS...3 DEFINITION OF SYMBOLS...4 RECOMMENDED TOOLS...4 ASSEMBLY INSTRUCTIONS...5 RADIOSTAR MIRROR FUNCTIONS...7 SIDE INTEGRATED CONTROL PANEL...8 REMOTE CONTROL...8 SETTINGS...9 TROUBLESHOOTING...12 CHANGING THE REMOTE CONTROL BATTERY...13 CHANGING THE STATION MEMORY / CLOCK BATTERY..13 CARE INSTRUCTIONS...13 SERVICE...14 TECHNICAL INFORMATION...14 DISPOSAL...14 CONTACT...14 INTRODUCTION Thank you for purchasing this HiB product. Please read through these instructions carefully and refer back to them during installation to ensure that your product is fi tted correctly and that it retains its high quality fi nish. This user s guide contains important information regarding the installation of the product and the usage of the technical functions. Please read all instructions carefully to ensure optimal performance. HiB assumes no liability if the instructions in this user s guide are ignored! Please retain this leaflet for future reference. PACK CONTENTS Before assembling and operating the RadioStar Mirror, please check that the contents are complete. Included in the package: - RadioStar Mirror (CR2032 Battery Included) - Remote Control (CR2025 Battery Included) - Fixings (4x 8mm wall plugs, 4x 25mm screws)

2 SAFETY INSTRUCTIONS All installations must comply with guidelines which are based on a zonal concept. The colour coded diagram below illustrates this concept and must be followed to ensure the safe installation of bathroom lighting. These regulations apply to domestic installations only. Installations must be made in accordance with the current IEE wiring regulations and relevant building regulations. HiB recommends that all electrical bathroom products should only be fi tted by a suitably qualifi ed, Part P registered electrician. Do not place the mirror on the floor without edge protectors! Use a soft cover to prevent damage to the edges. The use of electronic high-frequency devices such as hairdryers or mobile phones next to the RadioStar Mirror can interfere with the reception. For optimal reception, please fi x the RadioStar Mirror next to a window. The mirror is splash-proof and has IP44 certifi cation. However, please avoid unnecessary splashes and moisture. This applies especially for the side-mounted loudspeakers, the remote control and the inside of the metal casing. DEFINITION OF SYMBOLS All safety precautions are marked with this symbol. Please read them carefully to avoid personal and material damage! Please switch off or disconnect all electrical fuses in the area in which you are working Components and devices marked with this symbol cannot be disposed of in domestic waste. RECOMMENDED TOOLS The following tools are recommended for assembly: - Spirit-level - Pencil - Impact drill - Phillips screwdriver - Insulated screwdriver

3 ASSEMBLY INSTRUCTIONS Remove the RadioStar Mirror, the remote control and the fi xing kit from the packaging. - Carefully lay the mirror fl at on the fl oor and check that the contents are complete. - Remove the four screws at the sides of the mirror with a Phillips screwdriver. - Ensure that there are no electrical wires or water pipes in the wall. - Drill the holes using an 8mm drill bit at the four marked positions. - Insert the wall plugs Make a hole in the rubber grommet on the back of the casing for the power cable. - Lift the steel casing, pull the power cable through the hole and screw the steel casing to the wall. - Take off the mirror surface carefully and place it fl at on a soft cloth to prevent damage. - Switch off the electrical fuses for the area in which you are working. - Hold the steel casing to the wall in the desired position. - Adjust the position with the spirit level to ensure that the mirror is straight. - Mark the position of each of the fi xing points with a pencil. - Connect the domestic power cable to the electric terminal of the RadioStar Mirror. - Please use an insulated screwdriver. - Replace the mirror surface and secure it to the steel casing by tightening the screws on the sides of the mirror. - Peel the protective fi lm from the mirror and switch on the electrical fuses

4 RADIOSTAR MIRROR FUNCTIONS SIDE INTEGRATED CONTROL PANEL LIGHTING The RadioStar Mirror is equipped with LED illumination for optimal and energy-saving performance. The lifetime of the LEDs is approximately 50,000 operating hours. MULTI-FUNCTION DISPLAY The easily viewable LED multi-function display shows the time, the station frequency and additional features. CONTROL PANEL / REMOTE CONTROL The side-integrated control panel and the remote control allow for functional and uncomplicated use. The radio memory is secured by a continuous power from an additional 3-volt lithium battery (CR included). The remote control requires a 3-volt lithium battery (CR included). The settings offer a 10-station memory, an alarm mode and a sleep timer. ANTENNA CONNECTION - The RadioStar Mirror is equipped with three integrated antennas to ensure the best reception quality. - Telescopic Antenna - Integrated Frame Antenna - External Antenna Connection Sleep-timer Selection of saved stations Volume down Station scan backwards REMOTE CONTROL On / off Presets 1-10 Sleep timer On / off Setting the time Volume up Station scan forwards Setting the time Selection of saved stations Volume - / + Station scan - /

5 SETTINGS Remove the plastic tab from the bottom of the remote control to establish the battery connection. On / Off Press POWER to switch the FM radio on / off. Volume Control Volume up with VOL+ or V+ / Volume down with VOL- or V-. Antenna The antenna consists of the telescopic antenna, the integrated frame antenna and the external antenna connection. - Frame antenna: The steel casing of the RadioStar Mirror is used. - Telescopic antenna: A telescopic antenna is mounted on top of the steel casing. When the antenna is half-extended, it can be clamped. In most cases, the antenna can be hidden from view. - External connection: There is an external antenna connection on the base of the telescopic antenna. This alternative should only be used if reception is not satisfactory, even after adjusting the telescopic antenna. Starting the Station Scan Automatically Start the station scan by pressing TUN+ or TUN- for approximately 3 seconds. Starting the Station Scan Manually Press TUN+ or TUN- in short intervals to adjust the stations manually. The FM radio reception can be optimized by adjusting the telescopic antenna. Station Memory with the Control Panel You can save up to 10 radio station presets. First, select your preferred FM station. Press TIME for 3 seconds, and then select where to save it by pressing PRESET repeatedly. Press TIME again to fi nish. Station Memory with the Remote Control You can save up to 10 radio station presets. First, select your preferred FM station. Press TIME for 3 seconds, and then select where to save it by pressing the number buttons Press TIME again to fi nish. Station Memory Changing If you try to save a new station under a preset that has already been assigned, the previous station will be deleted and the new one will be saved in its place. Selecting Saved Stations By pressing PRESET on the control panel, or by pressing the number buttons 1-10 on the remote control, the saved station will be selected. Setting the Time Mode 12 / 24 Hours The clock display can be set in 12 or 24 hours mode. Start by turning off the radio. Activate the clock mode by pressing TIME for 3 seconds. By pressing PRESET you can choose between 12 / 24 hours mode. Time will be displayed in the 12 hour mode if a dot appears in the upper left of the display. You are in 24 hour mode if the dot is not displayed. To save the selected time mode, press TIME. Setting the Time First, turn off the radio. Activate the clock mode by pressing TIME for 3 seconds. Adjust the minutes by pressing TUN-. Adjust the hours by pressing TUN+. Press TIME to save the time. Setting the Radio Alarm Clock To have the radio automatically turn on at a specifi c time, the clock must be set fi rst. Turn off the radio, and activate the radio alarm clock mode by pressing VOL- or V- for 3 seconds. Adjust the minutes by pressing TUN-. Adjust the hours by pressing TUN+. Press VOL- or V- to save the turn on time. The radio will turn on automatically to the most recently used frequency at the selected time

6 SETTINGS TROUBLESHOOTING Symptom Possible Problem Solution Power LED - not working No electricity supply Power LED - segment not working Some LEDs are burned out Soldering porous LEDs - not working No electricity supply Not connected within steel casing No sound from loudspeakers Radio not turned on No electricity supply Not connected within steel casing Remote control not working Protective plastic tab between battery and connecters not been removed Lithium battery empty No station reception No electricity supply Radio not turned on Telescopic antenna not extended and adjusted Poor station reception Telescopic antenna not extended and adjusted Telescopic antenna not correctly adjusted Usage of high frequency devices near the RadioStar Mirror Telescopic Antenna not effective No stations saved after switching off electricity Lithium battery not inserted in battery case within steel frame Lithium battery empty Contact your local dealer to replace the LED plate Check connections inside steel casing Turn on radio Check connections inside steel casing Pull out plastic tab at the bottom of the remote control Replace the battery (CR2025) Turn on radio Extend telescopic antenna and adjust it Extend telescopic antenna and adjust it Adjust telescopic antenna Switch off other electronic devices Connect external FM antennad Insert the lithium battery inside the unit Replace the battery (CR2032) Setting the Acoustic Alarm Clock To have the acoustic signal sound at a specifi c time, the clock must be set fi rst. Turn off the radio, and activate the acoustic alarm clock mode by pressing VOL+ or V+ for 3 seconds. Adjust the minutes by pressing TUN-. Adjust the hours by pressing TUN+. Press VOL+ or V+ to save the turn on time. The acoustic signal will sound at the selected time and will turn off automatically after one minute; to turn the acoustic signal off sooner, press any button. The radio alarm clock / acoustic alarm clock settings are only possible with the power supply connected. If you have connected the RadioStar Mirror to a light switch in your bathroom, make sure that the light switch is turned on, otherwise no alarm will sound. Turning the Radio Alarm Clock On/Off Once set, you can switch the radio alarm clock on or off by pressing VOL- or V-. Turning the Acoustic Alarm Clock On/Off Once set, you can switch the acoustic alarm clock on or off by pressing VOL+ or V+. Setting the Sleep-Timer The automatic shutdown function of the radio can be set for a specifi ed time frame. The sleep timer will be displayed by pressing SLEEP. If you press SLEEP again, you can choose the minutes (minimum 10 minutes up to a maximum of 90 minutes) after which the radio will shut down automatically. The time will be displayed in ten minute intervals. The settings are automatically saved after 4 seconds. To deactivate the sleep timer, press SLEEP until the word OFF appears in the display to confi rm the deactivation. ipod/mp3 Connection By using an FM transmitter (not supplied), available from any good electrical retailer, you can tune the radio to the FM transmitter and listen to your ipod or MP3 player

7 CHANGING THE REMOTE CONTROL BATTERY There is a sketch on the back of the remote control which demonstrates how to replace the battery (CR2025). CHANGING THE STATION MEMORY / CLOCK BATTERY SERVICE All of our products are tested for quality, function and electronic safety before delivery. If you require any further information, or you have questions or concerns about using our products, please contact your local specialist dealer. CARE INSTRUCTIONS To support the station memory and the clock memory, even when the mirror is not connected to a power supply, a lithium battery is installed in the radio unit. On average, this battery lasts for two years. To change the battery, follow the instructions below: - Switch off the electrical fuses in the area that you are working. - Loosen the screws on the sides of the steel casing with a Phillips screwdriver. Take off the mirror surface carefully and place it fl at on a soft cloth to prevent damage. - Open the battery case in the radio unit by sliding it to the right. - Take out the lithium battery and replace it with a new one (CR2032). - Reverse all previous instructions to reassemble the RadioStar Mirror. TECHNICAL INFORMATION 240 volts, 50Hz Radio: 12 volts, maximum 7.2 watts LED: 22 x watts = 2.75 watts (Tempo) 18 x watts = 2.25 watts (Acoustia) IP Rating: IP44 Operating Temperature: 0 C - 55 C (32 F F) Storage Temperature: -10 C - 60 C (14 F F) Size: 70 x 50cm (Tempo) 60 x 80cm (Acoustia) Article Number: (Tempo) (Acoustia) DISPOSAL To preserve the high quality fi nish of your HiB product, please ensure you regard the following care and cleaning recommendations: - wipe off all water spillages as soon as possible - mirrors and glass can be cleaned with a soft damp cloth. - scourers and scouring agents should not be used, as they may cause damage to the surface of the product - do not use sharp blades or solvent to peel off the protective fi lm With an environmentally-friendly disposal, you can prevent environmental contamination. Please check on how to dispose of used electronic devices and exhausted batteries in accordance with local regulations. Please recycle packaging where possible. CONTACT HiB Ltd, Castle House, Station Road, New Barnet, Herts, EN5 1PH, UK t: f: e: sales@hib.co.uk w:

User manual. Register your product and get support at Clock Radio Radio-réveil AJB3000

User manual. Register your product and get support at Clock Radio Radio-réveil AJB3000 Clock Radio Radio-réveil User manual AJB3000 Register your product and get support at www.philips.com/support Contents 1 Important 1 Safety 1 Risk of swallowing batteries! 1 Notice 1 2 Your FM/DAB radio