VCCI TEST REPORT. TESTED : June 22 to 23, 2010 APPLICANT : LOGITECH FAR EAST LTD.

Transcription

1 VCCI TEST REPORT REPORT NO. : V990621E07 MODEL NO. : M-U0026 RECEIVED : June 21, 2010 TESTED : June 22 to 23, 2010 ISSUED : June 24, 2010 APPLICANT : LOGITECH FAR EAST LTD. ADDRESS : #2 Creation Rd. 4, Science-Based Ind. Park Hsinchu Taiwan, R.O.C. ISSUED BY : Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch Hsin Chu Laboratory LAB ADDRESS : No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan TEST LOCATION (1): No. 81-1, Lu Liao Keng, 9th Ling,Wu Lung Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan TEST LOCATION (2): No. 49, Ln. 206, Wende Rd., Shangshan Tsuen, Chiung Lin Hsiang, Hsin Chu Hsien 307, Taiwan This test report consists of 20 pages in total. It may be duplicated completely for legal use with the approval of the applicant. It should not be reproduced except in full, without the written approval of our laboratory. The client should not use it to claim product certification, approval, or endorsement by TAF or any government agencies. The test results in the report only apply to the tested sample. Report No.: V990621E07 1 Report Format Version 3.0.2

2 Table of Contents 1 CERTIFICATION SUMMARY OF TEST RESULTS MEASUREMENT UNCERTAINTY GENERAL INFORMATION GENERAL DESCRIPTION OF EUT GENERAL DESCRIPTION OF TEST MODE DESCRIPTION OF SUPPORT UNITS CONFIGURATION OF SYSTEM UNDER TEST EMISSION TEST CONDUCTED EMISSION MEASUREMENT LIMITS OF CONDUCTED EMISSION MEASUREMENT TEST INSTRUMENTS TEST PROCEDURE DEVIATION FROM TEST STANDARD TEST SETUP EUT OPERATING CONDITIONS TEST RESULTS RADIATED EMISSION MEASUREMENT LIMITS OF RADIATED EMISSION MEASUREMENT TEST INSTRUMENTS TEST PROCEDURE DEVIATION FROM TEST STANDARD TEST SETUP EUT OPERATING CONDITIONS TEST RESULTS PHOTOGRAPHS OF THE TEST CONFIGURATION INFORMATION ON THE TESTING LABORATORIES...20 Report No.: V990621E07 2 Report Format Version 3.0.2

3 1 CERTIFICATION PRODUCT : Corded Mouse BRAND NAME : Logitech MODEL NO : M-U0026 APPLICANT : LOGITECH FAR EAST LTD. TESTED : June 22 to 23, 2010 TEST SAMPLE : ENGINEERING SAMPLE STANDARDS : V-3/ , TECHNICAL REQUIREMENTS, Class B V-4/ , SUPPLEMENTARY TEST CONDITIONS FOR EQUIPMENT UNDER TEST The above equipment (Model: M-U0026) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample s EMC characteristics under the conditions specified in this report. PREPARED BY :, DATE: June 24, 2010 ( Carol Liao, Specialist ) TECHNICAL ACCEPTANCE :, DATE: June 24, 2010 ( Ray Yeh, Deputy Manager ) APPROVED BY :, DATE: June 24, 2010 ( May Chen, Deputy Manager ) Report No.: V990621E07 3 Report Format Version 3.0.2

4 2 SUMMARY OF TEST RESULTS The EUT has been tested according to the following specifications: Standard Test Type Result Remarks Conducted Test PASS Meets Class B Limit Minimum passing margin is db at MHz V-3/ , Class B Telecom port conducted emission test NA Not Applicable Radiated Test PASS Meets Class B Limit Minimum passing margin is -7.5 db at MHz 2.1 MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR : This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k=2. Measurement Conducted emissions Radiated emissions(30mhz-1ghz) Value 2.45 db 3.21 db Report No.: V990621E07 4 Report Format Version 3.0.2

5 3 GENERAL INFORMATION 3.1 GENERAL DESCRIPTION OF EUT PRODUCT Corded Mouse MODEL NO. M-U0026 POWER SUPPLY DC 5V from host equipment POWER CORD NA DATA CABLE USB cable (shielded, 1.85 m) SUPPLIED INTERFACE USB interface NOTE: 1. For a more detailed features description, please refer to the manufacturer's specifications or the User's Manual. 3.2 GENERAL DESCRIPTION OF TEST MODE The EUT was tested under following test mode: Test Mode Mode 1 Description Normal mode Report No.: V990621E07 5 Report Format Version 3.0.2

6 3.3 DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units. The following support units or accessories were used to form a representative test configuration during the tests. Conducted test No. Product Brand Model No. Serial No. FCC ID 1 PERSONAL COMPUTER DELL DCSM G84QL1S FCC DoC 2 MONITOR DELL E228WFPc CN-OX765G P-0BTM FCC DoC 3 PRINTER EPSON LQ-300+ DCGY FCC DoC 4 MODEM ACEEX IFAXDM KEYBOARD DELL SK-8115 MY-0DJ B-0476 FCC DoC Radiated test No. Product Brand Model No. Serial No. FCC ID 1 PERSONAL COMPUTER DELL DCSCMF 9KKB32S FCC DoC 2 MONITOR DELL E2210Hc CN-OG337R S-OQDS FCC DoC 3 PRINTER CANON K10202 FASF84644 FCC DoC 4 MODEM ACEEX IFAXDM KEYBOARD DELL SK-8115 MY-0DJ B-0476 FCC DoC No. Signal cable description 1 NA m braid shielded wire, terminated with VGA connector via metallic frame, with two cores m braid shielded wire, terminated with DB25 and centronics connector via metallic frame, w/o core m braid shielded wire, terminated with DB25 and DB9 connector via metallic frame, w/o core m foil shielded wire, terminal by frame, USB Connector, w/o Core. NOTE: All power cords of the above support units are non shielded (1.8m). 3.4 CONFIGURATION OF SYSTEM UNDER TEST 3. PRINTER 1. PC 2. MONITOR 4. MODEM USB cable (1.85m) 5. KEYBOARD EUT TEST TABLE Report No.: V990621E07 6 Report Format Version 3.0.2

7 4 EMISSION TEST 4.1 CONDUCTED EMISSION MEASUREMENT LIMITS OF CONDUCTED EMISSION MEASUREMENT FREQUENCY (MHz) Class A (dbuv) Class B (dbuv) Quasi-peak Average Quasi-peak Average NOTES: (1) The lower limit shall apply at the transition frequencies. (2) The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50 MHz. (3) All emanations from a class A/B digital device or system, including any network of conductors and apparatus connected thereto, shall not exceed the level of field strengths specified above TEST INSTRUMENTS DESCRIPTION & MANUFACTURER ROHDE & SCHWARZ Test Receiver Line-Impedance Stabilization Network (for EUT) Line-Impedance Stabilization Network (for Peripheral) MODEL NO. SERIAL NO. CALIBRATED DATE CALIBRATED UNTIL ESCS Mar. 01, 2010 Feb. 28, 2011 NSLK Sep. 23, 2009 Sep. 22, 2010 ENV June 11, 2010 June 10, 2011 RF Cable (JYEBAO) 5DFB COACAB-001 Dec. 14, 2009 Dec. 13, ohms Terminator 50 3 Oct. 28, 2009 Oct. 27, 2010 Software BV ADT_Cond_V7.3.7 NA NA NA Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in Shielded Room No. A. 3 The VCCI Con A Registration No. is C-817. Report No.: V990621E07 7 Report Format Version 3.0.2

8 4.1.3 TEST PROCEDURE a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 Ohm/ 50uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The frequency range from 150 khz to 30 MHz was searched. Emission levels under (Limit 20dB) were not recorded DEVIATION FROM TEST STANDARD No deviation TEST SETUP Vertical Reference Ground Plane Test Receiver 40cm EUT LISN 80cm Note: 1.Support units were connected to second LISN. 2.Both of LISNs (AMN) are 80 cm from EUT and at least 80 cm from other units and other metal planes Horizontal Reference Ground Plane For the actual test configuration, please refer to the related Item Photographs of the Test Configuration. Report No.: V990621E07 8 Report Format Version 3.0.2

9 4.1.6 EUT OPERATING CONDITIONS 1. Turn on the power of all equipment. 2. Set the EUT under typical use condition. 3. PC runs test program mspaint.exe. 4. PC sends "H" messages to monitor, and displays H messages on its screen. 5. PC sends "H" messages to modem. 6. PC sends "H" messages to printer, and the printer prints them on paper. 7. Repeat steps 2-6. Report No.: V990621E07 9 Report Format Version 3.0.2

10 4.1.7 TEST RESULTS TEST MODE Mode 1 6dB BANDWIDTH 9 khz INPUT POWER (SYSTEM) ENVIRONMENTAL CONDITIONS 100Vac, 50 Hz PHASE Line (L) 25 deg. C, 60 % RH, 1014 hpa TESTED BY Max Tseng Freq. Corr. Reading Value Emission Level Limit Margin No Factor [db (uv)] [db (uv)] [db (uv)] (db) [MHz] (db) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. Margin value = Emission level - Limit value 5. Correction factor = Insertion loss + Cable loss 6. Emission Level = Correction Factor + Reading Value. Report No.: V990621E07 10 Report Format Version 3.0.2

11 TEST MODE Mode 1 6dB BANDWIDTH 9 khz INPUT POWER (SYSTEM) ENVIRONMENTAL CONDITIONS 100Vac, 50 Hz PHASE Neutral (N) 25 deg. C, 60 % RH, 1014 hpa TESTED BY Max Tseng Freq. Corr. Reading Value Emission Level Limit Margin No Factor [db (uv)] [db (uv)] [db (uv)] (db) [MHz] (db) Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV REMARKS: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. "-": The Quasi-peak reading value also meets average limit and measurement with the average detector is unnecessary. 3. The emission levels of other frequencies were very low against the limit. 4. Margin value = Emission level - Limit value 5. Correction factor = Insertion loss + Cable loss 6. Emission Level = Correction Factor + Reading Value. Report No.: V990621E07 11 Report Format Version 3.0.2

12 4.2 RADIATED EMISSION MEASUREMENT LIMITS OF RADIATED EMISSION MEASUREMENT FOR FREQUENCY BELOW 1000 MHz FREQUENCY Class A (at 10m) Class B (at 10m) (MHz) dbuv/m dbuv/m FOR FREQUENCY ABOVE 1000 MHz FREQUENCY (GHz) Class A (dbuv/m) (at 3m) Class B (dbuv/m) (at 3m) PEAK AVERAGE PEAK AVERAGE 1 to to NOTE: (1) The lower limit shall apply at the transition frequencies. (2) Emission level (dbuv/m) = 20 log Emission level (uv/m). (3) All emanation from a class A/B digital device or system, including any network of conductors and apparatus connected thereto, shall not exceed the level of field strengths specified above. FREQUENCY RANGE OF RADIATED MEASUREMENT (For unintentional radiators) Highest frequency generated or Upper frequency of measurement used in the device or on which the device operates or tunes (MHz) Range (MHz) Below Up to 5 times of the highest Above 1000 frequency or 6 GHz, whichever is less Report No.: V990621E07 12 Report Format Version 3.0.2

13 4.2.2 TEST INSTRUMENTS DESCRIPTION & CALIBRATED CALIBRATED MODEL NO. SERIAL NO. MANUFACTURER DATE UNTIL Agilent E4443A MY Aug. 03, 2009 Aug. 02, 2010 Spectrum Analyzer E4443A MY Oct. 31, 2009 Oct. 30, 2010 Agilent N9039A MY Nov. 20, 2009 Nov. 19, 2010 Pre-Selector N9039A MY July 25, 2009 July 24, 2010 Agilent Signal Generator N5181A MY July 20, 2009 July 19, 2010 Mini-Circuits ZFL-1000VH2B AMP-ZFL-01 Nov. 18, 2009 Nov. 17, 2010 Pre-Amplifier ZFL-1000VH2B AMP-ZFL-02 Nov. 18, 2009 Nov. 17, 2010 Mini-Circuits Pre_Amplifier ZVA-183-S+ AMP-ZVA-01 Nov. 18, 2009 Nov. 17, 2010 (1~18GHz) SPACEK LABS (15~40GHz) SLKKa K16 NA NA SCHWARZBECK VULB Sep. 30, 2009 Sep. 29, 2010 Trilog Broadband Antenna VULB Sep. 30, 2009 Sep. 29, 2010 SCHWARZBECK BBHA Sep. 30, 2009 Sep. 29, 2010 Horn Antenna BBHA D-783 Sep. 30, 2009 Sep. 29, 2010 RF CABLE NA RF RF Dec. 24, 2009 Dec. 23, 2010 RF Software ADT_Radiated_ V NA NA NA CT Antenna Tower & Turn Table NA NA NA NA Note: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in 10m Chamber No. F. 3. The FCC Site Registration No. is The VCCI Site Registration No. is R-3252 & G The CANADA Site Registration No. is IC 7450H-1. Report No.: V990621E07 13 Report Format Version 3.0.2

14 4.2.3 TEST PROCEDURE a. The EUT was placed on the top of a rotating table 0.8 meters above the ground at a 10 meters Semi-anechoic chamber room. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 10 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The antenna is a broadband antenna, and its height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to quasi-peak detect function and specified bandwidth with maximum hold mode when the test frequency is below 1 GHz. NOTE: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for Quasi-peak detection (QP) at frequency below 1GHz DEVIATION FROM TEST STANDARD No deviation Report No.: V990621E07 14 Report Format Version 3.0.2

15 4.2.5 TEST SETUP For the actual test configuration, please refer to the related Item Photographs of the Test Configuration EUT OPERATING CONDITIONS Same as Report No.: V990621E07 15 Report Format Version 3.0.2

16 4.2.7 TEST RESULTS TEST MODE Mode1 INPUT POWER (SYSTEM) 100Vac, 50Hz FREQUENCY RANGE MHz DETECTOR FUNCTION & BANDWIDTH Quasi-Peak, 120kHz ENVIRONMENTAL CONDITIONS 27 deg. C, 75 % RH, 1014 hpa TESTED BY Kyle Huang No. ANTENNA POLARITY & TEST DISTANCE: HORIZONTAL AT 10 M Freq. (MHz) Emission Level (dbuv/m) Limit (dbuv/m) Margin (db) Antenna Height (m) Table Angle (Degree) Raw Value (dbuv) Correction Factor (db/m) QP H QP H QP H QP H QP H QP H REMARKS: 1. Emission level(dbuv/m)=raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (db/m) + Cable Factor (db) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level Limit value. Report No.: V990621E07 16 Report Format Version 3.0.2

17 TEST MODE Mode 1 FREQUENCY RANGE MHz INPUT POWER (SYSTEM) DETECTOR FUNCTION & BANDWIDTH 100Vac, 50Hz Quasi-Peak, 120kHz ENVIRONMENTAL CONDITIONS 27 deg. C, 75 % RH, 1014 hpa TESTED BY Kyle Huang No. ANTENNA POLARITY & TEST DISTANCE: VERTICAL AT 10 M Freq. (MHz) Emission Level (dbuv/m) Limit (dbuv/m) Margin (db) Antenna Height (m) Table Angle (Degree) Raw Value (dbuv) Correction Factor (db/m) QP V QP V QP V QP V QP V QP V REMARKS: 1. Emission level(dbuv/m)=raw Value(dBuV) + Correction Factor(dB/m) 2. Correction Factor(dB/m) = Antenna Factor (db/m) + Cable Factor (db) 3. The other emission levels were very low against the limit. 4. Margin value = Emission level Limit value. Report No.: V990621E07 17 Report Format Version 3.0.2

18 5 PHOTOGRAPHS OF THE TEST CONFIGURATION CONDUCTED EMISSION TEST Report No.: V990621E07 18 Report Format Version 3.0.2

19 RADIATED EMISSION TEST Report No.: V990621E07 19 Report Format Version 3.0.2

20 6 INFORMATION ON THE TESTING LABORATORIES We, Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, were founded in 1988 to provide our best service in EMC, Radio, Telecom and Safety consultation. Our laboratories are accredited and approved according to ISO/IEC 17025: Copies of accreditation certificates of our laboratories obtained from approval agencies can be downloaded from our web site: If you have any comments, please feel free to contact us at the following: Linko EMC/RF Lab: Tel: Fax: Hsin Chu EMC/RF Lab: Tel: Fax: Hwa Ya EMC/RF/Safety/Telecom Lab: Tel: Fax: Web Site: The address and road map of all our labs can be found in our web site also. --- END --- Report No.: V990621E07 20 Report Format Version 3.0.2

21 Page: 1

22 Page: 2

23 Page: 3

24 Page: 4