FCC TEST REPORT (15.407)

Transcription

1 FCC TEST REPORT (15.407) REPORT NO.: RF150508C06A-7 MODEL: WT2 FCC ID: A4R-WT2 RECEIVED: May 08, 2015 TESTED: Jun. 10, 2015 ~ Jun. 18, 2015 ISSUED: Aug. 05, 2016 APPLICANT: Google Inc. ADDRESS: 1600 Amphitheatre Parkway Mountain View California United States ISSUED BY: Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch LAB ADDRESS: No. 47-2, 14th Ling, Chia Pau Vil., Lin Kou Dist., New Taipei City, Taiwan ( R.O.C ) TEST LOCATION: No. 19, Hwa Ya 2nd Rd, Wen Hwa Vil., Kwei Shan Dist., Taoyuan City 33383, Taiwan (R.O.C.) This report should not be used by the client to claim product certification, approval, or endorsement by TAF or any government agencies. This report is for your exclusive use. Any copying or replication of this report to or for any other person or entity, or use of our name or trademark, is permitted only with our prior written permission. This report sets forth our findings solely with respect to the test samples identified herein. The results set forth in this report are not indicative or representative of the quality or characteristics of the lot from which a test sample was taken or any similar or identical product unless specifically and expressly noted. Our report includes all of the tests requested by you and the results thereof based upon the information that you provided to us. You have 60 days from date of issuance of this report to notify us of any material error or omission caused by our negligence, provided, however, that such notice shall be in writing and shall specifically address the issue you wish to raise. A failure to raise such issue within the prescribed time shall constitute your unqualified acceptance of the completeness of this report, the tests conducted and the correctness of the report contents. Unless specific mention, the uncertainty of measurement has been explicitly taken into account to declare the compliance or non-compliance to the specification. Report No.: RF150508C06A-7 1 of 85 Report Format Version 5.3.0

2 OF CONTENTS Preface...4 RELEASE CONTROL RECORD CERTIFICATION SUMMARY OF TEST RESULTS MEASUREMENT UNCERTAINTY GENERAL INFORMATION GENERAL DESCRIPTION OF EUT DESCRIPTION OF TEST MODES TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL DESCRIPTION OF SUPPORT UNITS CONFIGURATION OF SYSTEM UNDER TEST DUTY CYCLE TEST SIGNAL GENERAL DESCRIPTION OF APPLIED STANDARDS TEST TYPES AND RESULTS RADIATED AND BANDEDGE MEASUREMENT S OF RADIATED AND BANDEDGE MEASUREMENT S OF UNWANTED OUT OF THE RESTRICTED BANDS TEST INSTRUMENTS TEST PROCEDURES DEVIATION FROM TEST STANDARD TEST SETUP EUT OPERATING CONDITIONS TEST RESULTS CONDUCTED MEASUREMENT S OF CONDUCTED MEASUREMENT TEST INSTRUMENTS TEST PROCEDURES DEVIATION FROM TEST STANDARD TEST SETUP EUT OPERATING CONDITIONS TEST RESULTS TRANSMIT POWER MEASUREMENT S OF TRANSMIT POWER MEASUREMENT TEST SETUP TEST INSTRUMENTS TEST PROCEDURE DEVIATION FROM TEST STANDARD EUT OPERATING CONDITIONS TEST RESULTS PEAK POWER SPECTRAL DENSITY MEASUREMENT S OF PEAK POWER SPECTRAL DENSITY MEASUREMENT TEST SETUP TEST INSTRUMENTS TEST PROCEDURES DEVIATION FROM TEST STANDARD EUT OPERATING CONDITIONS TEST RESULTS FREQUENCY STABILITY S OF FREQUENCY STABILITY MEASUREMENT TEST SETUP TEST INSTRUMENTS TEST PROCEDURE Report No.: RF150508C06A-7 2 of 85 Report Format Version 5.3.0

3 4.5.5 DEVIATION FROM TEST STANDARD EUT OPERATING CONDITION TEST RESULTS dB BANDWIDTH MEASUREMENT S OF 6dB BANDWIDTH MEASUREMENT TEST SETUP TEST INSTRUMENTS TEST PROCEDURE DEVIATION FROM TEST STANDARD EUT OPERATING CONDITIONS TEST RESULTS PHOTOGRAPHS OF THE TEST CONFIGURATION INFORMATION ON THE TESTING LABORATORIES APPENDIX A - MODIFICATIONS RECORDERS FOR ENGINEERING CHANGES TO THE EUT BY THE LAB Report No.: RF150508C06A-7 3 of 85 Report Format Version 5.3.0

4 Preface To whom it may concern, We hereby declare that the integrated module-end product (FCC ID: A4R-WT2) is identical to the integrated module-end product (FCC ID: A4R-WT1) in the WLAN layout of the circuit, components and transmit power levels. The difference is only to add LTE function into the integrated module-end product and change the model name from WT1 to WT2. Based on the similarity between both modules, we hereby request to leverage the all test data of FCC ID: A4R-WT1 described as below to demonstrate the compliance of FCC ID: A4R-WT2 for part 15E. The list of reference details (Re-use the test data from the original integrated module-end product): Equipment Class NII Reference FCC ID A4R-WT1 4.1 Reference to the test sections from FCC test report RF150508C06-7 Radiated Emission and Bandedge Measurement 4.2 Conducted Emission Measurement 4.3 Transmit Power Measurement 4.4 Peak Power Spectral Density Measurement 4.5 Frequency Stability 4.6 6dB Bandwidth Measurement Report No.: RF150508C06A-7 4 of 85 Report Format Version 5.3.0

5 RELEASE CONTROL RECORD ISSUE NO. REASON FOR CHANGE DATE ISSUED RF150508C06A-7 Original release Aug. 05, 2016 Report No.: RF150508C06A-7 5 of 85 Report Format Version 5.3.0

6 1. CERTIFICATION PRODUCT Connectivity Bridge NAME/DESCRIPTION: MODEL: WT2 BRAND: Google APPLICANT: Google Inc. TESTED: Jun. 10, 2015 ~ Jun. 18, 2015 TEST SAMPLE: Identical Prototype STANDARDS: FCC Part 15, Subpart E (Section ) ANSI C The above equipment (model: WT2) has been tested by Bureau Veritas Consumer Products Services (H.K.) Ltd., Taoyuan Branch, and found compliance with the requirement of the above standards. The test record, data evaluation & Equipment Under Test (EUT) configurations represented herein are true and accurate accounts of the measurements of the sample s EMC characteristics under the conditions specified in this report. PREPARED BY :, DATE : Aug. 05, 2016 Evonne Liu / Specialist APPROVED BY :, DATE : Aug. 05, 2016 Stanley Wu / Assistant Manager Report No.: RF150508C06A-7 6 of 85 Report Format Version 5.3.0

7 2. SUMMARY OF TEST RESULTS The EUT has been tested according to the following specifications: STANDARD SECTION APPLIED STANDARD: FCC PART 15, SUBPART E (SECTION ) TEST TYPE RESULT (b)(6) AC Power Conducted Emission PASS (b/1/2/3) (b)(6) Radiated Emissions PASS Meet the requirement of limit. Minimum passing margin is dB at MHz. Meet the requirement of limit. Minimum passing margin is -1.08dB at 5714MHz (a/1/2/3) Max Average Transmit Power PASS Meet the requirement of limit (a/1/2/3) Peak Power Spectral Density PASS Meet the requirement of limit. NOTE: (e) 6dB bandwidth PASS Meet the requirement of limit. (U-NII-3 Band only) (g) Frequency Stability PASS Meet the requirement of limit Antenna Requirement PASS No antenna connector is used. 1. Only the test item for conducted and radiated emission had been tested for this addendum and the 5260 ~ 5320MHz and 5500 ~ 5700MHz conducted data is referring to module report (Report No.: RF140407E07-1). 2.1 MEASUREMENT UNCERTAINTY Where relevant, the following measurement uncertainty levels have been estimated for tests performed on the EUT as specified in CISPR : MEASUREMENT FREQUENCY UNCERTAINTY Conducted emissions 9kHz~30MHz 2.44 db 9kHz ~ 30MHz 2.14 db 30MHz ~ 200MHz 2.93 db Radiated emissions 200MHz ~1000MHz 2.95 db 1GHz ~ 18GHz 2.26 db 18GHz ~ 40GHz 1.94 db This uncertainty represents an expanded uncertainty expressed at approximately the 95% confidence level using a coverage factor of k = 2. Report No.: RF150508C06A-7 7 of 85 Report Format Version 5.3.0

8 3. GENERAL INFORMATION 3.1 GENERAL DESCRIPTION OF EUT PRODUCT NAME/DESCRIPTION MODEL POWER SUPPLY MODULATION TYPE MODULATION TECHNOLOGY TRANSFER RATE OPERATING FREQUENCY NUMBER OF CHANNEL OUTPUT POWER TYPE CONNECTOR DATA I/O PORTS ACCESSORY DEVICES Connectivity Bridge WT2 5.0Vdc (adapter) 256QAM, 64QAM, 16QAM, QPSK, BPSK OFDM a: 54.0/ 48.0/ 36.0/ 24.0/ 18.0/ 12.0/ 9.0/ 6.0Mbps n: up to MCS ac: up to V ~ 5240MHz, 5260 ~ 5320MHz, 5500 ~ 5700MHz, 5745 ~ 5825MHz 5180 ~ 5240MHz: 4 for a, n (20MHz) 2 for n (40MHz) 1 for ac (80MHz) 5260 ~ 5320MHz: 4 for a, n (20MHz) 2 for n (40MHz) 1 for ac (80MHz) 5500 ~ 5700MHz: 11 for a, n (20MHz) 5 for n (40MHz) 2 for ac (80MHz) 5745 ~ 5825MHz: 5 for a, n (20MHz) 2 for n (40MHz) 1 for ac (80MHz) 45.60mW for 5180 ~ 5240MHz 75.16mW for 5745 ~ 5825MHz FPCB antenna with 2.51dBi gain (5180 ~ 5240MHz) FPCB antenna with 1.79dBi gain (5745 ~ 5825MHz) NA Refer to Note as below Refer to user s manual Refer to Note as below Report No.: RF150508C06A-7 8 of 85 Report Format Version 5.3.0

9 NOTE: 1. The EUT contains following accessory devices. ITEM BRAND MODEL SPECIFICATION Adapter TPT MII I/P: Vac, 50-60Hz, 0.3A O/P: 5Vdc, 2A WWAN Module Telit LE910-NAG -- WiFi Module AzureWave AW-CM389NF The EUT provides 1 completed transmitter and 1 receiver. MODULATION MODE TX FUNCTION a 1TX n (20MHz) 1TX n (40MHz) 1TX ac (80MHz) 1TX 3. The above EUT information is declared by the manufacturer and for more detailed features description, please refer to the manufacturer's specifications or User's Manual. Report No.: RF150508C06A-7 9 of 85 Report Format Version 5.3.0

10 3.2 DESCRIPTION OF TEST MODES WLAN 5180 ~ 5240MHz 4 channels are provided for a, n (20MHz): CHANNEL FREQUENCY CHANNEL FREQUENCY MHz MHz MHz MHz 2 channels are provided for n (40MHz): CHANNEL FREQUENCY CHANNEL FREQUENCY MHz MHz 1 channel is provided for ac (80MHz): CHANNEL FREQUENCY MHz FOR 5260 ~ 5320MHz 4 channels are provided for a, n (20MHz): CHANNEL FREQUENCY CHANNEL FREQUENCY MHz MHz MHz MHz 2 channels are provided for n (40MHz): CHANNEL FREQUENCY CHANNEL FREQUENCY MHz MHz 1 channel is provided for ac (80MHz): CHANNEL FREQUENCY MHz Report No.: RF150508C06A-7 10 of 85 Report Format Version 5.3.0

11 WLAN 5500 ~ 5700MHz 11 channels are provided for a, n (20MHz): CHANNEL FREQUENCY CHANNEL FREQUENCY MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz MHz 5 channels are provided for n (40MHz): CHANNEL FREQUENCY CHANNEL FREQUENCY MHz MHz MHz MHz MHz 2 channel is provided for ac (80MHz): CHANNEL FREQUENCY MHz FOR 5.0GHz (5745 ~ 5825MHz): 5 channels are provided for a, n (20MHz): CHANNEL FREQUENCY CHANNEL FREQUENCY MHz MHz MHz MHz MHz 2 channels are provided for n (40MHz): CHANNEL FREQUENCY CHANNEL FREQUENCY MHz MHz 1 channel is provided for ac (80MHz): CHANNEL FREQUENCY MHz Report No.: RF150508C06A-7 11 of 85 Report Format Version 5.3.0

12 3.2.1 TEST MODE APPLICABILITY AND TESTED CHANNEL DETAIL EUT CONFIGURE MODE APPLI TO RE 1G RE<1G PLC APCM - - DESCRIPTION Where RE 1G: Radiated Emission above 1GHz RE<1G: Radiated Emission below 1GHz PLC: Power Line Conducted Emission APCM: Antenna Port Conducted Measurement RADIATED TEST (ABOVE 1GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT CONFIGURE MODE MODE a BAND AVAILABLE CHANNEL TESTED CHANNEL MODULATION TECHNOLOGY MODULATION TYPE DATA RATE (Mbps) 36 to 48 36, 44, 48 OFDM BPSK n (20MHz) 36 to 48 36, 44, 48 OFDM BPSK MCS n (40MHz) 38 to 46 38, 46 OFDM BPSK MCS ac (80MHz) OFDM BPSK V a 52 to 64 52, 60, 64 OFDM BPSK n (20MHz) 52 to 64 52, 60, 64 OFDM BPSK MCS n (40MHz) 54 to 62 54, 62 OFDM BPSK MCS ac (80MHz) OFDM BPSK V a 100 to , 116, 140 OFDM BPSK n (20MHz) 100 to , 116, 140 OFDM BPSK MCS n (40MHz) 102 to , 110, 134 OFDM BPSK MCS ac (80MHz) 106 to , 102 OFDM BPSK V a 149 to , 157, 165 OFDM BPSK n (20MHz) 149 to , 157, 165 OFDM BPSK MCS n (40MHz) 151 to , 159 OFDM BPSK MCS ac (80MHz) OFDM BPSK V0 RADIATED TEST (BELOW 1GHz): Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT CONFIGURE MODE MODE BAND AVAILABLE CHANNEL TESTED CHANNEL MODULATION MODULATION TECHNOLOGY TYPE DATA RATE (Mbps) n (40MHz) to OFDM BPSK MCS0 Report No.: RF150508C06A-7 12 of 85 Report Format Version 5.3.0

13 POWER LINE CONDUCTED TEST: EUT CONFIGURE MODE MODE BAND AVAILABLE CHANNEL TESTED CHANNEL MODULATION MODULATION TECHNOLOGY TYPE DATA RATE (Mbps) n (40MHz) to OFDM BPSK MCS0 BANDEDGE MEASUREMENT: Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT CONFIGURE MODE - - MODE a BAND AVAILABLE CHANNEL TESTED CHANNEL MODULATION TECHNOLOGY MODULATION TYPE DATA RATE (Mbps) 36 to 48 36, 44, 48 OFDM BPSK n (20MHz) 36 to 48 36, 44, 48 OFDM BPSK MCS n (40MHz) 38 to 46 38, 46 OFDM BPSK MCS ac (80MHz) OFDM BPSK V a 149 to , 157, 165 OFDM BPSK n (20MHz) 149 to , 157, 165 OFDM BPSK MCS n (40MHz) 151 to , 159 OFDM BPSK MCS ac (80MHz) OFDM BPSK V0 PORT CONDUCTED MEASUREMENT: This item includes all test value of each mode, but only includes spectrum plot of worst value of each mode. Pre-Scan has been conducted to determine the worst-case mode from all possible combinations between available modulations, data rates and antenna ports (if EUT with antenna diversity architecture). Following channel(s) was (were) selected for the final test as listed below. EUT CONFIGURE MODE - - MODE a BAND AVAILABLE CHANNEL TESTED CHANNEL MODULATION TECHNOLOGY MODULATION TYPE DATA RATE (Mbps) 36 to 48 36, 44, 48 OFDM BPSK n (20MHz) 36 to 48 36, 44, 48 OFDM BPSK MCS n (40MHz) 38 to 46 38, 46 OFDM BPSK MCS ac (80MHz) OFDM BPSK V a 149 to , 157, 165 OFDM BPSK n (20MHz) 149 to , 157, 165 OFDM BPSK MCS n (40MHz) 151 to , 159 OFDM BPSK MCS ac (80MHz) OFDM BPSK V0 Report No.: RF150508C06A-7 13 of 85 Report Format Version 5.3.0

14 TEST CONDITION: APPLI TO ENVIRONMENTAL CONDITIONS INPUT POWER TESTED BY RE 1G 25deg. C, 65%RH 120Vac, 60Hz Hwa Chiang, Charles Hsiao RE<1G 25deg. C, 65%RH 120Vac, 60Hz Charles Hsiao PLC 25deg. C, 65%RH 120Vac, 60Hz Toby Tian APCM 25deg. C, 65%RH 120Vac, 60Hz Luke Chen 3.3 DESCRIPTION OF SUPPORT UNITS The EUT has been tested as an independent unit together with other necessary accessories or support units CONFIGURATION OF SYSTEM UNDER TEST EUT (Power from AC Adapter) *Test Table Report No.: RF150508C06A-7 14 of 85 Report Format Version 5.3.0

15 3.4 DUTY CYCLE TEST SIGNAL MODULATION TYPE: BPSK If duty cycle is < 98%, duty factor shall be considered a: Duty cycle = 2.099/4.583 = 0.458, Duty factor = 10 * log(1/0.458) = n (20MHz): Duty cycle = 1.971/5.096 = 0.386, Duty factor = 10 * log(1/0.386) = n (40MHz): Duty cycle = 0.945/5.032 = 0.187, Duty factor = 10 * log(1/0.187) = ac (80MHz): Duty cycle = 0.448/5.160 = 0.087, Duty factor = 10 * log(1/0.087) = a n (20MHz) n (40MHz) ac (80MHz) Report No.: RF150508C06A-7 15 of 85 Report Format Version 5.3.0

16 MODULATION TYPE: QPSK If duty cycle is < 98%, duty factor shall be considered a: Duty cycle = 1.057/2.596 = 0.407, Duty factor = 10 * log(1/0.407) = n (20MHz): Duty cycle = 0.993/4.871 = 0.203, Duty factor = 10 * log(1/0.203) = n (40MHz): Duty cycle = 0.464/4.230 = 0.109, Duty factor = 10 * log(1/0.109) = ac (80MHz): Duty cycle = 0.224/5.160 = 0.043, Duty factor = 10 * log(1/0.043) = a n (20MHz) n (40MHz) ac (80MHz) Report No.: RF150508C06A-7 16 of 85 Report Format Version 5.3.0

17 MODULATION TYPE: 16QAM If duty cycle is < 98%, duty factor shall be considered a: Duty cycle = 0.544/2.035 = 0.267, Duty factor = 10 * log(1/0.267) = n (20MHz): Duty cycle = 0.512/5.032 = 0.101, Duty factor = 10 * log(1/0.101) = n (40MHz): Duty cycle = 0.224/5.993 = 0.037, Duty factor = 10 * log(1/0.037) = ac (80MHz): Duty cycle = 0.128/5.160 = 0.024, Duty factor = 10 * log(1/0.024) = a n (20MHz) n (40MHz) ac (80MHz) Report No.: RF150508C06A-7 17 of 85 Report Format Version 5.3.0

18 MODULATION TYPE: 64QAM If duty cycle is < 98%, duty factor shall be considered a: Duty cycle = 0.280/1.818 = 0.154, Duty factor = 10 * log(1/0.154) = n (20MHz): Duty cycle = 0.288/5.384 = 0.053, Duty factor = 10 * log(1/0.053) = n (40MHz): Duty cycle = 0.128/5.897 = 0.021, Duty factor = 10 * log(1/0.021) = ac (80MHz): Duty cycle = 0.080/5.160 = 0.015, Duty factor = 10 * log(1/0.015) = a n (20MHz) n (40MHz) ac (80MHz) Report No.: RF150508C06A-7 18 of 85 Report Format Version 5.3.0

19 MODULATION TYPE: 256QAM If duty cycle is < 98%, duty factor shall be considered ac (80MHz): Duty cycle = 0.048/5.160 = 0.009, Duty factor = 10 * log(1/0.009) = ac (80MHz) Report No.: RF150508C06A-7 19 of 85 Report Format Version 5.3.0

20 3.5 GENERAL DESCRIPTION OF APPLIED STANDARDS The EUT is a RF Product. According to the specifications of the manufacturer, it must comply with the requirements of the following standards: FCC Part 15, Subpart E (15.407) D02 General UNII Test Procedures New Rules v01r D01 Guidance for IEEE ac v01r02 ANSI C All test items have been performed and recorded as per the above standards. NOTE: The EUT has been verified to comply with the requirements of FCC Part 15, Subpart B, Class B (DoC). The test report has been issued separately. Report No.: RF150508C06A-7 20 of 85 Report Format Version 5.3.0

21 4. TEST TYPES AND RESULTS 4.1 RADIATED AND BANDEDGE MEASUREMENT S OF RADIATED AND BANDEDGE MEASUREMENT Radiated emissions which fall in the restricted bands must comply with the radiated emission limits specified as below table: FREQUENCIES FIELD STRENGTH (microvolts/meter) MEASUREMENT DISTANCE (meters) ~ /F(kHz) ~ /F(kHz) ~ ~ ~ ~ Above NOTE: 1. The lower limit shall apply at the transition frequencies. 2. Emission level = 20 log Emission level (uv/m). 3. For frequencies above 1000MHz, the field strength limits are based on average detector, however, the peak field strength of any emission shall not exceed the maximum permitted average limits, specified above by more than 20dB under any condition of modulation S OF UNWANTED OUT OF THE RESTRICTED BANDS APPLI TO D02 General UNII Test Procedures New Rules v01 APPLI TO (b)(1) PK: 74 (dbµv/m) EIRP FIELD STRENGTH AT 3m AV: 54 (dbµv/m) EQUIVALENT FIELD STRENGTH AT 3m (b)(2) PK: -27 (dbm/mhz) PK: 68.2 (dbµv/m) (b)(3) (b)(4) NOTE: *1 beyond 10MHz of the band edge Report No.: RF150508C06A-7 21 of 85 Report Format Version PK: -27 (dbm/mhz) *1 PK: 68.2 (dbµv/m) *1 PK: -17 (dbm/mhz) *2 PK: 78.2 (dbµv/m) *2 *2 within 10 MHz of band edge The following formula is used to convert the equipment isotropic radiated power (eirp) to field strength: E = P µv/m, where P is the eirp (Watts). 3

22 4.1.3 TEST INSTRUMENTS DESCRIPTION & MANUFACTURER MODEL NO. SERIAL NO. DATE OF CALIBRATION DUE DATE OF CALIBRATION Test Receiver Agilent N9038A MY Jan.21, 2015 Jan.21, 2016 Spectrum Analyzer Agilent N9010A MY Sep.03, 2014 Sep.02, 2015 Spectrum Analyzer ROHDE & SCHWARZ FSU Dec. 10, 2014 Dec. 09, 2015 BILOG Antenna SCHWARZBECK VULB Feb. 04, 2015 Feb. 04, 2016 HORN Antenna SCHWARZBECK BBHA 9120 D 9120D-969 Feb. 09, 2015 Feb. 09, 2016 HORN Antenna SCHWARZBECK BBHA Feb. 04, 2015 Feb. 04, 2016 Loop Antenna EM Aug.13, 2014 Aug.12, 2015 Preamplifier EMCI EMC Dec. 12, 2014 Dec. 11, 2015 Preamplifier EMCI EMC Jan. 09, 2015 Jan. 08, 2016 Preamplifier EMCI EMC 330H Dec. 27, 2014 Dec. 26, 2015 RF signal cable /4 SUCOFLEX 104 HUBER+SUHNNER Oct. 18, 2014 Oct. 17, 2015 RF signal cable HUBER+SUHNNER SUCOFLEX /4 Oct. 18, 2014 Oct. 17, 2015 RF signal cable Worken RG-213 NA Nov. 07, 2014 Nov. 06, 2015 Software E3 BV ADT NA NA NA Antenna Tower MF MFA-440H NA NA NA Turn Table MF MFT-201SS NA NA NA Antenna Tower &Turn Table Controller MF-7802 NA NA NA MF Bluetooth Tester CBT Feb. 10, 2015 Feb. 09, 2016 Power Meter ML2495A Sep. 17, 2014 Sep. 16, 2015 Power Sensor MA2411B Sep. 17, 2014 Sep. 16, 2015 NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The calibration interval of the loop antenna is 24 months and the calibrations are traceable to NML/ROC and NIST/USA. 3. The test was performed in HwaYa Chamber The horn antenna and HP preamplifier (model: 8449B) are used only for the measurement of emission frequency above 1GHz if tested. 5. The FCC Site Registration No. is The IC Site Registration No. is IC 7450F-10. Report No.: RF150508C06A-7 22 of 85 Report Format Version 5.3.0

23 4.1.4 TEST PROCEDURES a. The EUT was placed on the top of a rotating table 0.8 meters (for below 1GHz) / 1.5 meters (for above 1GHz) above the ground at 3 meter chamber room for test. The table was rotated 360 degrees to determine the position of the highest radiation. b. The EUT was set 3 meters away from the interference-receiving antenna, which was mounted on the top of a variable-height antenna tower. c. The antenna is a broadband antenna, and its height is varied from one meter to four meters above the ground to determine the maximum value of the field strength. Both horizontal and vertical polarizations of the antenna are set to make the measurement. d. For each suspected emission, the EUT was arranged to its worst case and then the antenna was tuned to heights from 1 meter to 4 meters and the rotatable table was turned from 0 degrees to 360 degrees to find the maximum reading. e. The test-receiver system was set to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. f. If the emission level of the EUT in peak mode was 10dB lower than the limit specified, then testing could be stopped and the peak values of the EUT would be reported. Otherwise the emissions that did not have 10dB margin would be re-tested one by one using peak, quasi-peak or average method as specified and then reported in a data sheet. NOTE: 1. The resolution bandwidth and video bandwidth of test receiver/spectrum analyzer is 120kHz for Peak detection (PK) and Quasi-peak detection (QP) at frequency below 1GHz. 2. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and video bandwidth is 3MHz for Peak detection at frequency above 1GHz. 3. The resolution bandwidth of test receiver/spectrum analyzer is 1MHz and the video bandwidth is 1kHz (Duty cycle < 98%) or 10Hz (Duty cycle > 98%) for Average detection (AV) at frequency above 1GHz. 4. All modes of operation were investigated and the worst-case emissions are reported DEVIATION FROM TEST STANDARD No deviation. Report No.: RF150508C06A-7 23 of 85 Report Format Version 5.3.0

24 4.1.6 TEST SETUP <Frequency Range 30MHz ~ 1GHz> EUT& Support Units 3m 10m Ant. Tower 1-4m Variable Turn Table 80cm Ground Plane Test Receiver <Frequency Range above 1GHz> EUT& Support Units 3m Ant. Tower 1-4m Variable Turn Table Absorber 150cm Ground Plane Test Receiver For the actual test configuration, please refer to the attached file (Test Setup Photo) EUT OPERATING CONDITIONS a. Placed the EUT on a testing table. b. Use the software to control the EUT under transmission condition continuously at specific channel frequency. Report No.: RF150508C06A-7 24 of 85 Report Format Version 5.3.0

25 4.1.8 TEST RESULTS ABOVE 1GHz WORST-CASE DATA a EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 36 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Hwa Chiang POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Average Peak Average Peak Average Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Average Peak Average Peak Average Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency. Report No.: RF150508C06A-7 25 of 85 Report Format Version 5.3.0

26 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 44 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Hwa Chiang POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Average Peak Average Peak Average Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Average Peak Average Peak Average Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency. Report No.: RF150508C06A-7 26 of 85 Report Format Version 5.3.0

27 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 48 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Hwa Chiang POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Average Peak Average Peak Average Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Average Peak Average Peak Average Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency. Report No.: RF150508C06A-7 27 of 85 Report Format Version 5.3.0

28 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 52 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Charles Hsiao POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Average Peak Average Peak Average Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Average Peak Average Peak Average Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency. Report No.: RF150508C06A-7 28 of 85 Report Format Version 5.3.0

29 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 60 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Charles Hsiao POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Average Peak Average Peak Average Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Average Peak Average Peak Average Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency. Report No.: RF150508C06A-7 29 of 85 Report Format Version 5.3.0

30 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 64 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Charles Hsiao POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Average Peak Average Peak Average Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Average Peak Average Peak Average Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency. Report No.: RF150508C06A-7 30 of 85 Report Format Version 5.3.0

31 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 100 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Charles Hsiao POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Average Peak Peak Average Peak Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Average Peak Peak Average Peak Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency MHz & 5725MHz: Out of restricted band Report No.: RF150508C06A-7 31 of 85 Report Format Version 5.3.0

32 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 116 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Charles Hsiao POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Average Peak Peak Average Peak Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Average Peak Peak Average Peak Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency MHz & 5725MHz: Out of restricted band Report No.: RF150508C06A-7 32 of 85 Report Format Version 5.3.0

33 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 140 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Charles Hsiao POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Average Peak Peak Average Peak Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Average Peak Peak Average Peak Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency MHz & 5725MHz: Out of restricted band Report No.: RF150508C06A-7 33 of 85 Report Format Version 5.3.0

34 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 149 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Charles Hsiao POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Peak Peak Average Peak Peak Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Peak Peak Average Peak Peak Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency MHz & 5724MHz, 5860MHz & 5866MHz: Out of restricted band 5714MHz & 5722MHz, 5852MHz & 5868MHz: Out of restricted band Report No.: RF150508C06A-7 34 of 85 Report Format Version 5.3.0

35 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 157 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Charles Hsiao POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Peak Peak Average Peak Peak Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Peak Peak Average Peak Peak Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency MHz & 5716MHz, 5854MHz & 5864MHz: Out of restricted band 5708MHz & 5720MHz, 5858MHz & 5864MHz: Out of restricted band Report No.: RF150508C06A-7 35 of 85 Report Format Version 5.3.0

36 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 165 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Charles Hsiao POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Peak Peak Average Peak Peak Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Peak Peak Average Peak Peak Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency MHz & 5720MHz, 5850MHz & 5864MHz: Out of restricted band 5710MHz & 5724MHz, 5852MHz & 5870MHz: Out of restricted band Report No.: RF150508C06A-7 36 of 85 Report Format Version 5.3.0

37 802.11n (20MHz) EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 36 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Hwa Chiang POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Average Peak Average Peak Average Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Average Peak Average Peak Average Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency. Report No.: RF150508C06A-7 37 of 85 Report Format Version 5.3.0

38 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 44 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Hwa Chiang POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Average Peak Average Peak Average Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Average Peak Average Peak Average Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency. Report No.: RF150508C06A-7 38 of 85 Report Format Version 5.3.0

39 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 48 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Hwa Chiang POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Average Peak Average Peak Average Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Average Peak Average Peak Average Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency. Report No.: RF150508C06A-7 39 of 85 Report Format Version 5.3.0

40 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 52 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Charles Hsiao POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Average Peak Average Peak Average Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Average Peak Average Peak Average Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency. Report No.: RF150508C06A-7 40 of 85 Report Format Version 5.3.0

41 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 60 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Charles Hsiao POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Average Peak Average Peak Average Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Average Peak Average Peak Average Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency. Report No.: RF150508C06A-7 41 of 85 Report Format Version 5.3.0

42 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 64 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Charles Hsiao POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Average Peak Average Peak Average Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Average Peak Average Peak Average Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency. Report No.: RF150508C06A-7 42 of 85 Report Format Version 5.3.0

43 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 100 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Charles Hsiao POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Average Peak Peak Average Peak Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Average Peak Peak Average Peak Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency MHz & 5725MHz: Out of restricted band Report No.: RF150508C06A-7 43 of 85 Report Format Version 5.3.0

44 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 116 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Charles Hsiao POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Average Peak Peak Average Peak Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Average Peak Peak Average Peak Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency MHz & 5725MHz: Out of restricted band Report No.: RF150508C06A-7 44 of 85 Report Format Version 5.3.0

45 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 140 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Charles Hsiao POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Average Peak Peak Average Peak Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Average Peak Peak Average Peak Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency MHz & 5725MHz: Out of restricted band Report No.: RF150508C06A-7 45 of 85 Report Format Version 5.3.0

46 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 149 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Charles Hsiao POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Peak Peak Average Peak Peak Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Peak Peak Average Peak Peak Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency MHz & 5724MHz, 5854MHz & 5862MHz: Out of restricted band 5712MHz & 5724MHz, 5856MHz & 5864MHz: Out of restricted band Report No.: RF150508C06A-7 46 of 85 Report Format Version 5.3.0

47 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 157 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Charles Hsiao POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Peak Peak Average Peak Peak Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Peak Peak Average Peak Peak Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency MHz & 5724MHz, 5858MHz & 5862MHz: Out of restricted band 5712MHz & 5724MHz, 5858MHz & 5868MHz: Out of restricted band Report No.: RF150508C06A-7 47 of 85 Report Format Version 5.3.0

48 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 165 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Charles Hsiao POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Peak Peak Average Peak Peak Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Peak Peak Average Peak Peak Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency MHz & 5722MHz, 5850MHz & 5862MHz: Out of restricted band 5714MHz & 5722MHz, 5850MHz & 5862MHz: Out of restricted band Report No.: RF150508C06A-7 48 of 85 Report Format Version 5.3.0

49 802.11n (40MHz) EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 38 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Hwa Chiang POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Average Peak Average Peak Average Peak Average POLARITY & TEST DISTANCE: VERTICAL AT 3 M Average Peak Average Peak Average Peak Average S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency. Report No.: RF150508C06A-7 49 of 85 Report Format Version 5.3.0

50 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 46 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Hwa Chiang POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Average Peak Average Peak Average Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Average Peak Average Peak Average Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency. Report No.: RF150508C06A-7 50 of 85 Report Format Version 5.3.0

51 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 54 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Charles Hsiao POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Average Peak Average Peak Average Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Average Peak Average Peak Average Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency. Report No.: RF150508C06A-7 51 of 85 Report Format Version 5.3.0

52 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 62 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Charles Hsiao POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Average Peak Average Peak Average Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Average Peak Average Peak Average Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency. Report No.: RF150508C06A-7 52 of 85 Report Format Version 5.3.0

53 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 102 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION Peak (PK) Average (AV) ENVIRONMENTAL CONDITIONS 25deg. C, 65%RH TESTED BY Charles Hsiao POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Average Peak Peak Average Peak Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Average Peak Peak Average Peak Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency MHz & 5725MHz: Out of restricted band Report No.: RF150508C06A-7 53 of 85 Report Format Version 5.3.0

54 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 110 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Charles Hsiao POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Average Peak Peak Average Peak Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Average Peak Peak Average Peak Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency MHz & 5725MHz: Out of restricted band Report No.: RF150508C06A-7 54 of 85 Report Format Version 5.3.0

55 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 134 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Charles Hsiao POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Average Peak Peak Average Peak Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Average Peak Peak Average Peak Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency MHz & 5725MHz: Out of restricted band Report No.: RF150508C06A-7 55 of 85 Report Format Version 5.3.0

56 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 151 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Charles Hsiao POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Peak Peak Average Peak Peak Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Peak Peak Average Peak Peak Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency MHz & 5724MHz, 5854MHz & 5870MHz: Out of restricted band 5714MHz & 5722MHz, 5858MHz & 5864MHz: Out of restricted band Report No.: RF150508C06A-7 56 of 85 Report Format Version 5.3.0

57 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 159 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Charles Hsiao POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Peak Peak Average Peak Peak Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Peak Peak Average Peak Peak Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency MHz & 5720MHz, 5854MHz & 5862MHz: Out of restricted band 5706MHz & 5722MHz, 5852MHz & 5870MHz: Out of restricted band Report No.: RF150508C06A-7 57 of 85 Report Format Version 5.3.0

58 802.11ac (80MHz) EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 42 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Hwa Chiang POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Average Peak Average Peak Average Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Average Peak Average Peak Average Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency. Report No.: RF150508C06A-7 58 of 85 Report Format Version 5.3.0

59 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 58 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Charles Hsiao POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Average Peak Average Peak Average Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Average Peak Average Peak Average Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency. Report No.: RF150508C06A-7 59 of 85 Report Format Version 5.3.0

60 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 106 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Charles Hsiao POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Average Peak Peak Average Peak Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Average Peak Peak Average Peak Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency MHz & 5725MHz: Out of restricted band Report No.: RF150508C06A-7 60 of 85 Report Format Version 5.3.0

61 EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 155 FREQUENCY RANGE 1GHz ~ 40GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Average (AV) 25deg. C, 65%RH TESTED BY Charles Hsiao POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Peak Peak Average Peak Peak Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Peak Peak Average Peak Peak Peak S: 1. Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value MHz: Fundamental frequency MHz & 5722MHz, 5854MHz & 5864MHz: Out of restricted band 5706MHz & 5718MHz, 5852MHz & 5870MHz: Out of restricted band Report No.: RF150508C06A-7 61 of 85 Report Format Version 5.3.0

62 BELOW 1GHz WORST-CASE DATA: n (40MHz) EUT TEST CONDITION MEASUREMENT DETAIL CHANNEL Channel 151 FREQUENCY RANGE 30MHz ~ 1GHz INPUT POWER 120Vac, 60 Hz DETECTOR FUNCTION ENVIRONMENTAL CONDITIONS Peak (PK) Quasi-peak (QP) 25deg. C, 65%RH TESTED BY Charles Hsiao POLARITY & TEST DISTANCE: HORIZONTAL AT 3 M Peak Peak Peak Peak Peak Peak POLARITY & TEST DISTANCE: VERTICAL AT 3 M Peak Peak Peak Peak Peak Peak S: Emission Level = Read Level + Antenna Factor + Cable Loss - Preamp Factor Margin value = Emission level Limit value Report No.: RF150508C06A-7 62 of 85 Report Format Version 5.3.0

63 4.2 CONDUCTED MEASUREMENT S OF CONDUCTED MEASUREMENT FREQUENCY OF CONDUCTED (dbµv) Quasi-peak Average 0.15 ~ ~ 5 5 ~ to to NOTE: 1. The lower limit shall apply at the transition frequencies. 2. The limit decreases in line with the logarithm of the frequency in the range of 0.15 to 0.50MHz. 3. All emanations from a class A/B digital device or system, including any network of conductors and apparatus connected thereto, shall not exceed the level of field strengths specified above TEST INSTRUMENTS DESCRIPTION & MANUFACTURER Test Receiver ROHDE & SCHWARZ RF signal cable Woken LISN ROHDE & SCHWARZ (EUT) LISN ROHDE & SCHWARZ (Peripheral) Software ADT MODEL NO. SERIAL NO. DATE OF CALIBRATION DUE DATE OF CALIBRATION ESCI Nov. 11, 2014 Nov. 10, D-FB Cable-HYC01-01 Dec. 26, 2014 Dec. 25, 2015 ESH3-Z /001 Mar. 02, 2015 Mar. 01, 2016 ESH3-Z Jul. 21, 2014 Jul. 20, 2015 BV ADT_Cond_ V NA NA NA NOTE: 1. The calibration interval of the above test instruments is 12 months and the calibrations are traceable to NML/ROC and NIST/USA. 2. The test was performed in HwaYa Shielded Room The VCCI Site Registration No. is C Report No.: RF150508C06A-7 63 of 85 Report Format Version 5.3.0

64 4.2.3 TEST PROCEDURES a. The EUT was placed 0.4 meters from the conducting wall of the shielded room with EUT being connected to the power mains through a line impedance stabilization network (LISN). Other support units were connected to the power mains through another LISN. The two LISNs provide 50 ohm/ 50uH of coupling impedance for the measuring instrument. b. Both lines of the power mains connected to the EUT were checked for maximum conducted interference. c. The frequency range from 150kHz to 30MHz was searched. Emission levels under (Limit - 20dB) was not recorded. NOTE: All modes of operation were investigated and the worst-case emissions are reported DEVIATION FROM TEST STANDARD No deviation. Report No.: RF150508C06A-7 64 of 85 Report Format Version 5.3.0

65 4.2.5 TEST SETUP Vertical Ground Reference Plane Test Receiver 40cm EUT 80cm LISN Horizontal Ground Reference Plane Note: 1.Support units were connected to second LISN. 2.Both of LISNs (AMN) are 80 cm from EUT and at least 80 from other units and other metal planes For the actual test configuration, please refer to the attached file (Test Setup Photo) EUT OPERATING CONDITIONS Same as section Report No.: RF150508C06A-7 65 of 85 Report Format Version 5.3.0

66 4.2.7 TEST RESULTS CONDUCTED WORST-CASE DATA: Frequency Range Input Power 150kHz ~ 30MHz 120Vac, 60Hz Detector Function & Resolution Bandwidth Environmental Conditions Quasi-Peak (QP) / Average (AV), 9kHz 25, 65%RH Tested by Toby Tian Test Date 2015/6/18 Phase Of Power : Line (L) No Frequency Correction Factor Reading Value Emission Level Limit Margin Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV Remarks: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value Report No.: RF150508C06A-7 66 of 85 Report Format Version 5.3.0

67 Frequency Range Input Power 150kHz ~ 30MHz 120Vac, 60Hz Detector Function & Resolution Bandwidth Environmental Conditions Quasi-Peak (QP) / Average (AV), 9kHz 25, 65%RH Tested by Toby Tian Test Date 2015/6/18 Phase Of Power : Neutral (N) No Frequency Correction Factor Reading Value Emission Level Limit Margin Q.P. AV. Q.P. AV. Q.P. AV. Q.P. AV Remarks: 1. Q.P. and AV. are abbreviations of quasi-peak and average individually. 2. The emission levels of other frequencies were very low against the limit. 3. Margin value = Emission level Limit value 4. Correction factor = Insertion loss + Cable loss 5. Emission Level = Correction Factor + Reading Value Report No.: RF150508C06A-7 67 of 85 Report Format Version 5.3.0