CE EMC Test Report. : Class 1 Bluetooth Data Module : BT740-SA, BT730-SA, BT740-SC, BT730-SC

Size: px

Start display at page:

Download "CE EMC Test Report. : Class 1 Bluetooth Data Module : BT740-SA, BT730-SA, BT740-SC, BT730-SC"

Winifred Campbell
5 years ago
Views:

17, 2013 We,, would like to declare that the tested sample has been evaluated and in compliance with the requirement of the above standards.

1 CE EMC Test Report Equipment Model No. Brand Name Applicant : Class 1 Bluetooth Data Module : BT740-SA, BT730-SA, BT740-SC, BT730-SC : Laird : Laird Technologies Address : Thompson Ave. / Lenexa, Kansas / / USA Standard : EN V1.9.2 ( ) EN V2.2.1 ( ) Received Date : Mar. 21, 2013 Tested Date : Apr. 16 ~ Apr. 17, 2013 We,, would like to declare that the tested sample has been evaluated and in compliance with the requirement of the above standards. It may be duplicated completely for legal use with the approval of the applicant. It shall not be reproduced except in full without the written approval of our laboratory. Approved & Reviewed by: Kent Chen / Assistant Manager Ty: Patricia Report No.: EH Page : 1 of 48

2 Table of Contents 1 GENERAL DESCRIPTION Information Local Support Equipment List Test Setup Chart Test Software and Operating Condition Test Equipment and Calibration Data Testing Applied Standards Measurement Uncertainty TEST CONFIGURATION Testing Condition The Worst Case Measurement Configuration EMISSION TEST RESULTS Conducted Emissions IMMUNITY TESTS General Description Performance Criteria Description Electrostatic Discharge (ESD) Radio Frequency Electromagnetic Field (RS) PHOTOGRAPHS OF THE TEST CONFIGURATION Report No.: EH Page : 2 of 48

3 Release Record Report No. Version Description Issued Date EH Rev. 01 Initial issue Apr. 22, 2013 Report No.: EH Page : 3 of 48

4 Summary of Test Results Ref. Std. Clause EN Emission Tests Test Standard Test Items Measured Result 8.3/8.4 EN 55022:2010, Class B Conducted Emissions [dbuv]: 0.175MHz (Margin 14.05dB) - QP Pass Ref. Std. Clause Test Standard EN Immunity Tests Test Items Pass Criterion 9.3 EN :2009 Electrostatic Discharge (ESD) A 9.2 EN :2006/A1:2008/A2:2010 Radio Frequency Electromagnetic Field (RS) A Report No.: EH Page : 4 of 48

5 1 General Description 1.1 Information Product Details The following models are provided to this EUT. Model Name Description Difference BT740-SA BT740-SC Class 1 Bluetooth Data Module Class 1 Bluetooth Data Module CCL Interface Express Subsystem 2.1+EDR. Integrated Antenna CCL Interface Express Subsystem 2.1+EDR. No integrated antenna, only U.FL RF connector for external antenna BT730-SA Class 1 Bluetooth Data Module CSR Unified Stack 2.0EDR. Integrated Antenna. BT730-SC Class 1 Bluetooth Data Module CSR Unified Stack 2.0EDR. No integrated antenna, only U.FL RF connector for external antenna Hardware is the same on all of these modules. Only difference is the Bluetooth firmware installed. The above models, model BT730-SA and BT730-SC were selected as representative ones for the final test and only its data was recorded in this report Specification of the Equipment under Test (EUT) Frequency Range (MHz) Bluetooth Mode RF General Information Ch. Frequency (MHz) Channel Number Data Rate BR V [79] 1 Mbps EDR V [79] 2 Mbps EDR V [79] 3 Mbps Note 1: Bluetooth BR uses a GFSK. Note 2: Bluetooth EDR uses a combination of π/4-dqpsk and 8DPSK Max Radio Power Table EUT Model Maximum Radio Power Table Conducted Power (dbm) BT740-SA, BT730-SA BT740-SC, BT730-SC Note: Maximum Radio Power Table entry used in the BT7xx-SA is 18dBm and for BT7xx-SC module is 16dBm. Report No.: EH Page : 5 of 48

6 1.1.4 Antenna Details Ant. No. EUT Model Type Gain (dbi) Connector ANT Brand/Model 1 2 BT740-SA BT730-SA Chip ACX/AT3216-B2R7HAAT ceramic Patch 2 UFL EZURiO/ACC BT740-SC PCB 2 UFL Laird/NanoBlue-IP04(MAF94045) 4 BT730-SC Dipole 2 UFL NEARSON/S181FL-L-RMM-2450S 5 Dipole 2 UFL Laird/WTC2450-IP04-K 6 Dipole 1.5 UFL Laird/WRR2400- IP04-B EUT Operational Condition Supply Voltage AC mains DC Type of DC Source Internal DC supply External DC adapter 3.3Vdc & 5Vdc from host Accessories N/A 1.2 Local Support Equipment List Support Equipment List No. Equipment Brand Name Model Name Serial No. 1 Notebook DELL Latitude E5430 6R4RWW1 2 Notebook DELL Latitude E RWW1 3 USB Dongle USB to RS232 cable Golden-s U Note: No. 3 was provided by client. Report No.: EH Page : 6 of 48

7 1.3 Test Setup Chart Test Setup Diagram (EMI) Test Setup Diagram (EMS) Report No.: EH Page : 7 of 48

8 1.4 Test Software and Operating Condition a. The EUT with fixture equipment connect to notebook via USB cable to provide DC voltage to EUT. b. The EUT with fixture equipment connect to notebook via USB to RS232 cable. c. Check com port No shown on management console. d. The notebook ran Teraterm.exe. e. The setting 9600/8bit/non/1bit/non and COM port number of step c was set to link up with notebook (in control area) which has a Bluetooth dongle. f. Check com port No shown on management console of the notebook (in control area) and ran Teraterm.exe. g. The setting 9600/8bit/non/1bit/non and COM port number of step f was set to link up with EUT. h. The notebook sent H patterns to notebook (in control area) via EUT and displayed them. i. The notebook (in control area) linked with EUT via USB dongle to receive and transmit data by BT. 1.5 Test Equipment and Calibration Data EMI Conducted Emission Test Site Conduction room 1 / (CO01-WS) Instrument Manufacturer Model No. Serial No. Calibration Date Calibration Until EMC Receiver R&S ESCS Dec. 12, 2012 Dec. 11, 2013 LISN LISN (Support Unit) SCHWARZBECK MESS-ELEKTRONIK SCHWARZBECK MESS-ELEKTRONIK Schwarzbeck Dec. 04, 2012 Dec. 03, 2013 Schwarzbeck Dec. 04, 2012 Dec. 03, 2013 ISN TESEQ ISN T Feb. 17, 2013 Feb. 16, 2014 ISN TESEQ ISN T Jun. 22, 2012 Jun. 21, 2013 ISN TESEQ ISN T8-Cat Sep. 17, 2012 Sep. 16, 2013 ISN TESEQ ISN ST Jan. 24, 2013 Jan. 23, 2014 RF Current Probe FCC F Dec. 04, 2012 Dec. 03, 2013 RF Cable-CON Woken CFD200-NL CFD200-NL-001 Dec. 25, 2012 Dec. 24, 2013 ESH3-Z6 V-Network R&S ESH3-Z Nov. 21, 2012 Nov. 20, 2013 Note: Calibration Interval of instruments listed above is one year. EMS ESD Test Site ESD room 1 / (ES01-WS) Instrument Manufacturer Model No. Serial No. Calibration Date Calibration Until ESD Generator EMTest Dito V Dec. 05, 2012 Dec. 04, 2013 Note: Calibration Interval of instruments listed above is one year. Report No.: EH Page : 8 of 48

9 EMS Test Site Radiated Immunity (80 MHz - 6 GHz) RS room 1 / (RS01-WS) Instrument Manufacturer Model No. Serial No. Calibration Date Calibration Until Probe ETS-LINDGREN HI Oct. 02, 2012 Oct. 01, 2013 Signal Generator R&S SMB 100A HA Jul. 01, 2012 Jun. 30, 2013 Power Sensor R&S NRP-Z UL Nov. 06, 2012 Nov. 05, 2013 Power Sensor R&S NRP-Z KY Nov. 06, 2012 Nov. 05, 2013 USB Adapter For NRP-Z USB Adapter For NRP-Z Power Amplifier R&S NRP-Z N/A N/A R&S NRP-Z N/A N/A BONN BLWA /100D A N/A N/A Power Amplifier BONN BLWA D B N/A N/A Antenna SCHWARZBECK MESS-ELEKTRONIK STLP N/A N/A Antenna R&S HL046E Cd N/A N/A Control SCU Maturo SCU/0525/ N/A N/A N/A System Control Unit R&S RF-EMS N/A N/A i-key R&S EMC32MS N/A N/A i-key R&S EMC32MK N/A N/A i-key R&S EMC32K N/A N/A i-key R&S EMC32MK N/A N/A Note: Calibration Interval of instruments listed above is one year. Report No.: EH Page : 9 of 48

10 1.6 Testing Applied Standards According to the specifications of the manufacturer, the EUT must comply with the requirements of the following standards: EN V1.9.2 ( ) EN V2.2.1 ( ) 1.7 Measurement Uncertainty ISO/IEC requires that an estimate of the measurement uncertainties associated with the emissions test results be included in the report. The measurement uncertainties given below are based on a 95% confidence level (based on a coverage factor (k=2) Measurement Uncertainty Test Item Frequency Uncertainty Conducted Emissions 150kHz ~ 30MHz 2.8 db Report No.: EH Page : 10 of 48

11 2 Test Configuration 2.1 Testing Condition Test Item Test Site Ambient Condition Tested By AC Conduction CO01-WS 22 C/67% Skys Huang ESD ES01-WS 26 C/50%/98kPa Eason Chang RS RS01-WS 24 C/56%/98kPa Eason Chang 2.2 The Worst Case Measurement Configuration The Worst Test Configurations Conducted Emissions Test Mode Operating Description 1 BT730-SA, Ant. 1, run Teraterm.exe, BT link 2 BT730-SC, Ant. 1, run Teraterm.exe, BT link 3 BT730-SC, Ant. 2, run Teraterm.exe, BT link 4 BT730-SC, Ant. 3, run Teraterm.exe, BT link 5 BT730-SC, Ant. 4, run Teraterm.exe, BT link 6 BT730-SC, Ant. 5, run Teraterm.exe, BT link Immunity Tests Test Mode Operating Description 1 BT730-SA, Ant. 1, run Teraterm.exe, BT link 2 BT730-SC, Ant. 1, run Teraterm.exe, BT link 3 BT730-SC, Ant. 2, run Teraterm.exe, BT link 4 BT730-SC, Ant. 3, run Teraterm.exe, BT link 5 BT730-SC, Ant. 4, run Teraterm.exe, BT link 6 BT730-SC, Ant. 5, run Teraterm.exe, BT link Report No.: EH Page : 11 of 48

12 3 Emission Test Results 3.1 Conducted Emissions Limit of Conducted Emissions Frequency Range (MHz) Class A (dbµv) Limits Class B (dbµv) Quasi-peak Average Quasi-peak Average 0.15 to to to to to Note 1: The lower limit shall apply at the transition frequencies. Note 2: The limit decreases linearly with the logarithm of the frequency in the range 0.15 MHz to 0.50 MHz Test Procedures a. The EUT was placed on a table with a height of 0.8 meters from the metal ground plane and 0.4 meters from the conducting wall of the shielding room and it was kept at least 0.8 meters from any other grounded conducting surface. b. The test equipment EUT installed received DC power through a Line Impedance Stabilization Network (LISN), which supplied power source and was grounded to the ground plane. c. All the support units were connected to the other LISN. d. The LISN provides 50 ohm coupling impedance for the measuring instrument. e. The CISPR states that a 50 ohm, 50 microhenry LISN should be used. f. Both sides of AC line were checked for maximum conducted interference. g. The measurement frequency range extends from 150 khz to 30 MHz. h. Set the test-receiver system to Peak Detect Function and Specified Bandwidth with Maximum Hold Mode. Report No.: EH Page : 12 of 48

13 3.1.3 Test Setup Report No.: EH Page : 13 of 48

14 3.1.4 Test Result of Conducted Emissions Power Phase Line Test Mode 1 Note 1: Level (dbuv) = Read Level (dbuv) + LISN Factor (db) + Cable Loss (db). 2: Over Limit (dbuv) = Limit Line (dbuv) Level (dbuv). Report No.: EH Page : 14 of 48

15 Power Phase Neutral Test Mode 1 Note 1: Level (dbuv) = Read Level (dbuv) + LISN Factor (db) + Cable Loss (db). 2: Over Limit (dbuv) = Limit Line (dbuv) Level (dbuv). Report No.: EH Page : 15 of 48

16 Power Phase Line Test Mode 2 Note 1: Level (dbuv) = Read Level (dbuv) + LISN Factor (db) + Cable Loss (db). 2: Over Limit (dbuv) = Limit Line (dbuv) Level (dbuv). Report No.: EH Page : 16 of 48

17 Power Phase Neutral Test Mode 2 Note 1: Level (dbuv) = Read Level (dbuv) + LISN Factor (db) + Cable Loss (db). 2: Over Limit (dbuv) = Limit Line (dbuv) Level (dbuv). Report No.: EH Page : 17 of 48

18 Power Phase Line Test Mode 3 Note 1: Level (dbuv) = Read Level (dbuv) + LISN Factor (db) + Cable Loss (db). 2: Over Limit (dbuv) = Limit Line (dbuv) Level (dbuv). Report No.: EH Page : 18 of 48

19 Power Phase Neutral Test Mode 3 Note 1: Level (dbuv) = Read Level (dbuv) + LISN Factor (db) + Cable Loss (db). 2: Over Limit (dbuv) = Limit Line (dbuv) Level (dbuv). Report No.: EH Page : 19 of 48

20 Power Phase Line Test Mode 4 Note 1: Level (dbuv) = Read Level (dbuv) + LISN Factor (db) + Cable Loss (db). 2: Over Limit (dbuv) = Limit Line (dbuv) Level (dbuv). Report No.: EH Page : 20 of 48

21 Power Phase Neutral Test Mode 4 Note 1: Level (dbuv) = Read Level (dbuv) + LISN Factor (db) + Cable Loss (db). 2: Over Limit (dbuv) = Limit Line (dbuv) Level (dbuv). Report No.: EH Page : 21 of 48

22 Power Phase Line Test Mode 5 Note 1: Level (dbuv) = Read Level (dbuv) + LISN Factor (db) + Cable Loss (db). 2: Over Limit (dbuv) = Limit Line (dbuv) Level (dbuv). Report No.: EH Page : 22 of 48

23 Power Phase Neutral Test Mode 5 Note 1: Level (dbuv) = Read Level (dbuv) + LISN Factor (db) + Cable Loss (db). 2: Over Limit (dbuv) = Limit Line (dbuv) Level (dbuv). Report No.: EH Page : 23 of 48

24 Power Phase Line Test Mode 6 Note 1: Level (dbuv) = Read Level (dbuv) + LISN Factor (db) + Cable Loss (db). 2: Over Limit (dbuv) = Limit Line (dbuv) Level (dbuv). Report No.: EH Page : 24 of 48

25 Power Phase Neutral Test Mode 6 Note 1: Level (dbuv) = Read Level (dbuv) + LISN Factor (db) + Cable Loss (db). 2: Over Limit (dbuv) = Limit Line (dbuv) Level (dbuv). Report No.: EH Page : 25 of 48

26 4 Immunity Tests 4.1 General Description Product Standard: EN , EN Basic Standard Spec. Requirement Performance Criteria EN (ESD) EN (RS) Contact Discharge: ± 4 kv Air Discharge: ± 8 kv MHz, MHz 3 V/m, 1 khz Sine Wave 80%, AM Modulation B A Report No.: EH Page : 26 of 48

27 4.2 Performance Criteria Description Performance criteria for Continuous phenomena applied to Transmitters (CT) Performance criteria for Transient phenomena applied to Transmitters (TT) Performance criteria for Continuous phenomena applied to Receivers (CR) Performance criteria for Transient phenomena applied to Receivers (TR) Performance Criteria The performance criteria A shall apply. The performance criteria B shall apply. The performance criteria A shall apply. The performance criteria B shall apply. Performance Table Criteria During test After test A B C Note 1: Note 2: Shall operate as intended. May show degradation of performance (see note1). Shall be no loss of function. Shall be no unintentional transmissions. May show loss of function (one or more). May show degradation of performance (see note 1). No unintentional transmissions. May be loss of function (one or more). Shall operate as intended. Shall be no degradation of performance (see note 2). Shall be no loss of function. Shall be no loss of stored data or user programmable functions. Functions shall be self-recoverable. Shall operate as intended after recovering. Shall be no degradation of performance (see note 2). Shall be no loss of stored data or user programmable functions. Functions shall be recoverable by the operator. Shall operate as intended after recovering. Shall be no degradation of performance (see note 2). Degradation of performance during the test is understood as a degradation to a level not below a minimum performance level specified by the manufacturer for the use of the apparatus as intended. In some cases the specified minimum performance level may be replaced by a permissible degradation of performance. If the minimum performance level or the permissible performance degradation is not specified by the manufacturer then either of these may be derived from the product description and documentation (including leaflets and advertising) and what the user may reasonably expect from the apparatus if used as intended. No degradation of performance after the test is understood as no degradation below a minimum performance level specified by the manufacturer for the use of the apparatus as intended. In some cases the specified minimum performance level may be replaced by a permissible degradation of performance. After the test no change of actual operating data or user retrievable data is allowed. If the minimum performance level or the permissible performance degradation is not specified by the manufacturer then either of these may be derived from the product description and documentation (including leaflets and advertising) and what the user may reasonably expect form the apparatus if used as intended. Report No.: EH Page : 27 of 48

28 4.3 Electrostatic Discharge (ESD) Test Specification of Electrostatic Discharge (ESD) Basic Standard EN Discharge Voltage Discharge Impedance Number of Discharge Discharge Mode Discharge Period Contact Discharge: ± 2 kv / ± 4 kv Air Discharge: ± 2 kv / ± 4 kv / ± 8 kv 330 ohm / 150 pf Air Discharge: minimum 20 times at each test point Contact Discharge: minimum 20 times at each test point Single Discharge 1 second minimum Test Procedures a. In the case of air discharge testing the climatic conditions shall be within the following ranges: - ambient temperature: 15 C to 35 C; - relative humidity : 30% to 60%; - atmospheric pressure : 86 kpa (860 mbar) to 106 kpa (1060 mbar). b. Test programs and software shall be chosen so as to exercise all normal modes of operation of the EUT. The use of special exercising software is encouraged, but permitted only where it can be shown that the EUT is being comprehensively exercised. c. The test voltage shall be increased from the minimum to the selected test severity level, in order to determine any threshold of failure. The final severity level should not exceed the product specification value in order to avoid damage to the equipment. d. The test shall be performed with both air discharge and contact discharge. On preselected points at least 10 single discharges (in the most sensitive polarity) shall be applied on air discharge. On preselected points at least 10 single discharges (in the most sensitive polarity) shall be applied on contact discharge. e. For the time interval between successive single discharges an initial value of one second is recommended. Longer intervals may be determined whether a system failure has occurred. f. In the case of contact discharges, the tip of the discharge electrode shall touch the EUT before the discharge switch is operated. g. In the case of painted surface covering a conducting substrate, the following procedure shall be adopted: - If the coating is not declared to be an insulating coating by the equipment manufacturer, then the pointed tip of the generator shall penetrate the coating so as to make contact with the conducting substrate. - Coating declared as insulating by the manufacturer shall only be submitted to the air discharge. - The contact discharge test shall not be applied to such surfaces. h. In the case of air discharges, the round discharge tip of the discharge electrode shall be approached as fast as possible (without causing mechanical damage) to touch the EUT. After each discharge, the ESD generator (discharge electrode) shall be removed from the EUT. The generator is then retriggered for a new single discharge. This procedure shall be repeated until the discharges are completed. In the case of an air discharge test, the discharge switch, which is used for contact discharge, shall be closed. Report No.: EH Page : 28 of 48

29 4.3.3 Test Setup The test setup shall consist of a non-conductive table, (0.8 ± 0.08) m high, standing on the ground reference plane. A horizontal coupling plane (HCP), (1.6 ± 0.02) m (0.8 ± 0.02) m, shall be placed on the table. The EUT and its cables shall be isolated from the coupling plane by an insulating support (0.5 ± 0.05) mm in thickness. Report No.: EH Page : 29 of 48

30 4.3.4 Test Result of Electrostatic Discharge (ESD) Test Mode 1 Test Point At front, rear, left and right side Test Point Polarity Indirect Application Test Voltage (kv) Horizontal Coupling Plane (HCP) Vertical Coupling Plane (VCP) Performance Criteria +/- 2,4 Note 1 Note 1 A Polarity Direct Application Test Voltage (kv) Horizontal Coupling Plane (HCP) Vertical Coupling Plane (VCP) Performance Criteria Note1: No performance degradation was observed. Test Mode 2 Test Point At front, rear, left and right side Test Point Polarity Indirect Application Test Voltage (kv) Horizontal Coupling Plane (HCP) Vertical Coupling Plane (VCP) Performance Criteria +/- 2,4 Note 1 Note 1 A Polarity Direct Application Test Voltage (kv) Horizontal Coupling Plane (HCP) Vertical Coupling Plane (VCP) Performance Criteria Note1: No performance degradation was observed. Test Mode 3 Test Point At front, rear, left and right side Test Point Polarity Indirect Application Test Voltage (kv) Horizontal Coupling Plane (HCP) Vertical Coupling Plane (VCP) Performance Criteria +/- 2,4 Note 1 Note 1 A Polarity Direct Application Test Voltage (kv) Horizontal Coupling Plane (HCP) Vertical Coupling Plane (VCP) Performance Criteria Note1: No performance degradation was observed. Report No.: EH Page : 30 of 48

31 Test Mode 4 Test Point At front, rear, left and right side Test Point Polarity Indirect Application Test Voltage (kv) Horizontal Coupling Plane (HCP) Vertical Coupling Plane (VCP) Performance Criteria +/- 2,4 Note 1 Note 1 A Polarity Direct Application Test Voltage (kv) Horizontal Coupling Plane (HCP) Vertical Coupling Plane (VCP) Performance Criteria Note1: No performance degradation was observed. Test Mode 5 Test Point At front, rear, left and right side Test Point Polarity Indirect Application Test Voltage (kv) Horizontal Coupling Plane (HCP) Vertical Coupling Plane (VCP) Performance Criteria +/- 2,4 Note 1 Note 1 A Polarity Direct Application Test Voltage (kv) Horizontal Coupling Plane (HCP) Vertical Coupling Plane (VCP) Performance Criteria Note1: No performance degradation was observed. Test Mode 6 Test Point At front, rear, left and right side Test Point Polarity Indirect Application Test Voltage (kv) Horizontal Coupling Plane (HCP) Vertical Coupling Plane (VCP) Performance Criteria +/- 2,4 Note 1 Note 1 A Polarity Direct Application Test Voltage (kv) Horizontal Coupling Plane (HCP) Vertical Coupling Plane (VCP) Performance Criteria Note1: No performance degradation was observed. Report No.: EH Page : 31 of 48

32 4.4 Radio Frequency Electromagnetic Field (RS) Test Specification of Radio Frequency Electromagnetic Field (RS) Basic Standard EN Frequency Range Field Strength Modulation Frequency Step Polarity of Antenna Antenna Height Dwell Time 80 MHz ~ 1000 MHz, 1400 MHz to 2700 MHz 3 V/m 1 khz Sine Wave, 80%, AM Modulation 1 % of preceding frequency value Horizontal and Vertical 1.5 m 3 seconds Note: The exclusion band for the transmitter and / or receiver part of the 2.45 GHz RLAN equipment under test shall extend from 2280 MHz to MHz Test Procedures a. The test level shall be 3 V/m (measured unmodulated). The test signal shall be amplitude modulated to a depth of 80 % by a sinusoidal audio signal of 1000 Hz. If the wanted signal is modulated at 1000 Hz, then an audio signal of 400 Hz shall be used. b. The test shall be performed over the frequency range 80 MHz to 1000 MHz & 1400MHz to 2700MHz with the exception of the exclusion band for transmitters, receivers and duplex transceivers, as appropriate. c. For receivers and transmitters the stepped frequency increments shall be 1 % frequency increment of the momentary used frequency, unless specified otherwise in the part of EN series [i.13] dealing with the relevant type of radio equipment. d. Further product related spot frequency tests may be specified in the relevant part of EN series [i.13] dealing with the particular type of radio equipment. e. Responses on receivers occurring at discrete frequencies, which are narrow band responses, shall be disregarded from the test. f. The frequencies selected and used during the test shall be recorded in the test report. Report No.: EH Page : 32 of 48

4.4.3 Test Setup Note: The procedure defined in this part requires the generation of electromagnetic fields within which the test sample is placed and its operation observed.

33 4.4.3 Test Setup Note: The procedure defined in this part requires the generation of electromagnetic fields within which the test sample is placed and its operation observed. To generate fields that are useful for simulation of actual (field) conditions may require significant antenna drive power and the resultant high field strength levels. To comply with local regulations and to prevent biological hazards to the testing personnel, it is recommended that these tests be carried out in a shielded enclosure or semi-anechoic chamber. Report No.: EH Page : 33 of 48

34 4.4.4 Test Result of Radio Frequency Electromagnetic Field (RS) Test Mode 1 Frequency Range (MHz) Azimuth Polarity Test Field Strength (V/m) Observation Performance Criteria V&H 3 Note A V&H 3 Note A V&H 3 Note A V&H 3 Note A V&H 3 Note A V&H 3 Note A V&H 3 Note A V&H 3 Note A Note: No performance degradation was observed. Test Mode 2 Frequency Range (MHz) Azimuth Polarity Test Field Strength (V/m) Observation Performance Criteria V&H 3 Note A V&H 3 Note A V&H 3 Note A V&H 3 Note A V&H 3 Note A V&H 3 Note A V&H 3 Note A V&H 3 Note A Note: No performance degradation was observed. Report No.: EH Page : 34 of 48

35 Test Mode 3 Frequency Range (MHz) Azimuth Polarity Test Field Strength (V/m) Observation Performance Criteria V&H 3 Note A V&H 3 Note A V&H 3 Note A V&H 3 Note A V&H 3 Note A V&H 3 Note A V&H 3 Note A V&H 3 Note A Note: No performance degradation was observed. Test Mode 4 Frequency Range (MHz) Azimuth Polarity Test Field Strength (V/m) Observation Performance Criteria V&H 3 Note A V&H 3 Note A V&H 3 Note A V&H 3 Note A V&H 3 Note A V&H 3 Note A V&H 3 Note A V&H 3 Note A Note: No performance degradation was observed. Report No.: EH Page : 35 of 48

36 Test Mode 5 Frequency Range (MHz) Azimuth Polarity Test Field Strength (V/m) Observation Performance Criteria V&H 3 Note A V&H 3 Note A V&H 3 Note A V&H 3 Note A V&H 3 Note A V&H 3 Note A V&H 3 Note A V&H 3 Note A Note: No performance degradation was observed. Test Mode 6 Frequency Range (MHz) Azimuth Polarity Test Field Strength (V/m) Observation Performance Criteria V&H 3 Note A V&H 3 Note A V&H 3 Note A V&H 3 Note A V&H 3 Note A V&H 3 Note A V&H 3 Note A V&H 3 Note A Note: No performance degradation was observed. Report No.: EH Page : 36 of 48

37 5 Photographs of the Test Configuration Conducted Emission Test BT730-SA, Ant.1 Report No.: EH Page : 37 of 48

38 BT730-SC, Ant.1 Report No.: EH Page : 38 of 48

39 BT730-SC, Ant.2 Report No.: EH Page : 39 of 48

40 BT730-SC, Ant.3 Report No.: EH Page : 40 of 48

41 BT730-SC, Ant.4 Report No.: EH Page : 41 of 48

42 BT730-SC, Ant.5 Report No.: EH Page : 42 of 48

43 BT730-SA, Ant.1 ESD Test RS Test Report No.: EH Page : 43 of 48

44 BT730-SC, Ant.1 ESD Test RS Test Report No.: EH Page : 44 of 48

45 BT730-SC, Ant.2 ESD Test RS Test Report No.: EH Page : 45 of 48

46 BT730-SC, Ant.3 ESD Test RS Test Report No.: EH Page : 46 of 48

47 BT730-SC, Ant.4 ESD Test RS Test Report No.: EH Page : 47 of 48

48 BT730-SC, Ant.5 ESD Test RS Test END Report No.: EH Page : 48 of 48

FCC 15B Test Report. : BTv4.0 Dual Mode USB Dongle. Address : Thompson Ave. / Lenexa, Kansas / / USA

FCC 15B Test Report. : BTv4.0 Dual Mode USB Dongle. Address : Thompson Ave. / Lenexa, Kansas / / USA FCC 15B Test Report Equipment Model No. Brand Name Applicant : BTv4.0 Dual Mode USB Dongle : BT820 : Laird Technologies : Laird Technologies Address : 11160 Thompson Ave. / Lenexa, Kansas / 66219 / USA