Wide Operating Temperature Automotive Digital Optocoupler with R 2 Coupler Isolation and 5-Pin SMT Package. Features. Applications ANODE

Size: px

Start display at page:

Download "Wide Operating Temperature Automotive Digital Optocoupler with R 2 Coupler Isolation and 5-Pin SMT Package. Features. Applications ANODE"

Stephanie Hamilton
5 years ago
Views:

1 ACPL-MT Wide Operating Temperature Automotive Digital Optocoupler with R 2 Coupler Isolation and -Pin SMT Package Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxe denotes a lead-free product Description The ACPL-MT is a single channel, high temperature, high CMR, high speed digital optocoupler in a five lead miniature footprint specifically used in the automotive applications. The SO- JEDEC registered (MO-) package outline does not require through holes in a PCB. This package occupies approximately one-fourth the footprint area of the standard dual-in-line package. The lead profile is designed to be compatible with standard surface mount processes. This digital optocoupler uses an insulating layer between the light emitting diode and an integrated photon detector to provide electrical insulation between input and output. Separate connections for the photodiode bias and output transistor collector increase the speed up to a hundred times over that of a conventional photo-transistor coupler by reducing the base-collector capacitance. The ACPL-MT has an increased common mode transient immunity of kv/ s minimum at V CM = V over extended temperature range. Avago R 2 Coupler isolation products provide the reinforced insulation and reliability needed for critical in automotive and high temperature industrial applications. Functional Diagram ANODE CATHODE + V F SHIELD 6 I F Truth Table LED Vo ON LOW OFF HIGH I CC I O Note: The connection of a. F bypass capacitor between pins and 6 is recommended. V CC GND Features High Temperature and Reliability IPM Driver for Automotive Application. kv/ s High Common-Mode Rejection at V CM = V (typ) Compact, Auto-Insertable SO Packages Wide Temperature Range: - C ~ 2 C High Speed: MBd (Typ) Low LED Drive Current: ma (typ) Low Propagation Delay: ns (typ) Qualified to AEC-Q Test Guidelines Worldwide Safety Approval: UL77 recognized, Vrms/min CSA Approved IEC/EN/DIN EN Approved Applications Automotive IPM Driver for DC-DC converters and motor inverters CANBus Communications Interface High Temperature Digital/Analog Signal Isolation Power Transistor Isolation Pin Connections ANODE CATHODE 6 V CC MT YWW EE UT GND CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD.

2 Ordering Information Option Part number RoHS Compliant Package Surface Mount Tape & Reel IEC/EN/DIN EN Quantity ACPL-MT -E SO- X per tube -6E X X per tube -E X X per reel -6E X X X per reel To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example : ACPL-MT-E to order product of Mini-flat Surface Mount -pin package in Tape and Reel packaging with RoHS compliant. Example 2: ACPL-MT to order product of Mini-flat Surface Mount -pin package in tube packaging and non RoHS compliant. Option datasheets are available. Contact your Avago sales representative or authorized distributor for information. Package Outline Drawings ACPL-MT Small Outline SO- Package (JEDEC MO-) LAND PATTERN RECOMMENDATION. (.7). ±. (.7 ±.) MT YWW EE 7. ±.2 (.276 ±.8) 2. (.). (.) 2. (.8) 8.27 (.2).6 (.2). ±. (.6 ±.2) DIMENSIONS IN MILLIMETERS AND (INCHES).6 ±.* (.2 ±.) Extended Datecode for lot tracking 2. ±. (.98 ±.).2 ±.2 (. ±.).2 ±.2 (.8 ±.).27 (.) BSC.7 (.28) MIN. 7 o MAX. DIMENSIONS IN MILLIMETERS (INCHES) * MAXIMUM MOLD FLASH ON EACH SIDE IS. mm (.6) NOTE: FLOATING LEAD PROTRUSION IS. mm (6 mils) MAX. MAX. LEAD COPLANARITY =.2 (.) 2

3 Recommended reflow condition as per JEDEC Standard, J-STD-2 (latest revision). Note: Non-halide flux should be used. Regulatory Information The ACPL-MT is approved by the following organizations: UL Approved under UL 77, component recognition program up to V ISO = V RMS CSA Approved under CSA Component Acceptance Notice #. IEC/EN/DIN EN Approved under: IEC 677--:27 EN :2 + A DIN EN (VDE 88 Teil 2) IEC/EN/DIN EN Insulation Characteristics* Description Symbol Characteristic Unit Installation classification per DIN VDE /.89, Table for rated mains voltage V rms for rated mains voltage Vrms for rated mains voltage 6 V rms Climatic Classification /2/2 Pollution Degree (DIN VDE /.89) 2 Maximum Working Insulation Voltage V IORM 67 V peak Input to Output Test Voltage, Method b* V IORM x.87=v PR, % Production Test with t m = sec, Partial discharge < pc V PR 6 V peak Input to Output Test Voltage, Method a* V IORM x.6=v PR, Type and Sample Test, t m = sec, Partial discharge < pc I IV I III I II V PR 97 V peak Highest Allowable Overvoltage (Transient Overvoltage t ini = 6 sec) V IOTM 6 V peak Safety-limiting values maximum values allowed in the event of a failure. Case Temperature Input Current Output Power T S I S, INPUT P S, OUTPUT Insulation Resistance at T S, V IO = V R S > 9 * Refer to the optocoupler section of the Isolation and Control Components Designer s Catalog, under Product Safety Regulations section, (IEC/EN/ DIN EN ) for a detailed description of Method a and Method b partial discharge test profiles. Insulation and Safety Related Specifications Parameter Symbol ACPL-MT Units Conditions C ma mw Minimum External Air Gap (Clearance) Minimum External Tracking (Creepage) Minimum Internal Plastic Gap (Internal Clearance) Tracking Resistance (Comparative Tracking Index) Isolation Group (DIN VDE9) L() mm Measured from input terminals to output terminals, shortest distance through air. L(2) mm Measured from input terminals to output terminals, shortest distance path along body..8 mm Through insulation distance conductor to conductor, usually the straight line distance thickness between the emitter and detector. CTI 7 V DIN IEC 2/VDE Part IIIa Material Group (DIN VDE 9)

4 Absolute Maximum Ratings Parameter Symbol Min. Max. Units Note Storage Temperature T S - C Operating Temperature T A - 2 C Lead Soldering Cycle Temperature 26 C Time s Average Forward Input Current I F(avg) 2 ma Peak Forward Input Current I F(peak) ma (% duty cycle, ms pulse width) Peak Transient Input Current I F(trans) ma (<= us pulse width, ps) Reversed Input Voltage V R V Pin - Input Power Dissipation P IN mw Output Power Dissipation P O mw Average Output Current I O 8 ma Peak Output Current Io(pk) 6 ma Supply Voltage (Pins 6-) V CC -. V Output Voltage (Pins -) -. 2 V Solder Reflow Temperature Profile See Reflow Temperature Profile Recommended Operating Conditions Parameter Symbol Min. Max. Units Note Supply Voltage V CC. 2. V Operating Temperature T A - 2 C

5 Electrical Specifications (DC) Over recommended operating T A = - C to 2 C, unless otherwise specified. Parameter Sym. Min. Typ. Max. Units Conditions Fig. Note Current Transfer Ratio Logic Low Output Voltage Logic High Output Current Logic Low Supply Current Logic High Supply Current Input Forward Voltage Input Reversed Breakdown Voltage Temperature Coefficient of Forward Voltage CTR 2 8 % T A =2 C Vo=.V Vcc=.V 2 % Vo=.V I F =ma L.. V T A =2 C Io=mA. V Io=2.mA,2, I OH. A T A =2 C Vo=Vcc=.V I F =ma, 2 A T A =2 C Vo=Vcc=2V A I CCL 2 A I F =ma, Vo=open, Vcc=2V I CCH.2 A T A =2 C I F =ma, Vo=open, 2. A Vcc=2V V F...7 V T A =2 C I F =ma.2..8 V I F =ma BV R V I R = A V/ -. mv/ C I F =ma T A Input Capacitance C IN 9 pf F=MHz, V F = 7 7

6 Switching Specifications (AC) Over recommended operating (T A = - C to 2 C), I F = ma, V CC =. V unless otherwise specified. Parameter Symbol Min Typ Max Units Test Conditions Fig. Note Propagation Delay Time to Logic Low at Output Propagation Delay Time to Logic High at Output Pulse Width Distortion Propagation Delay Difference Between Any 2 Parts Common Mode Transient Immunity at Logic High Output Common Mode Transient Immunity at Logic Low Output μs T A =2 C Pulse: f=khz, Duty cycle =%,.6. μs I F = ma, V CC =. V, R L =.9k C L = pf V THHL =.V...8 μs T A =2 C Pulse: f=khz, Duty cycle =%,.. μs I F = ma, V CC =. V, R L =.9k C L = pf V THLH =2.V PWD.. μs T A =2 C Pulse: f=khz, Duty cycle =%,.8 μs I F =ma, V CC =.V, R L =.9k, C L =pf, V THHL =.V, V THLH =2.V t PLH -t PHL.. μs T A =2 C Pulse: f=khz, Duty cycle =%,.9 μs I F =ma, V CC =.V, R L =.9k, C L =pf, V THHL =.V, V THLH =2.V CM H kv/μs V CM =Vp-p, I F =ma, T A =2 C, R L =.9k CM L kv/μs V CM =Vp-p, I F =ma, T A =2 C, R L =.9k,6,7, 8,9,,,6,7, 8,9,, 8 9, Package Characteristics *The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous voltage rating. Parameter Symbol Min. Typ. Max. Units Test Conditions Fig. Note Input-Output Momentary Withstand Voltage* V ISO V RMS RH %, t = min; T A = 2 C Input-Output Resistance R I-O V I-O = Vdc 2 Input-Output Capacitance C I-O.6 pf f = MHz; V I-O = Vdc 2 Notes:. CURRENT TRANSFER RATIO in percent is defined as the ratio of output collector current, I O, to the forward LED input current, I F, times. 2. Device considered a two terminal device: pins and shorted together, and pins, and 6 shorted together.. In accordance with UL 77, each optocoupler is proof tested by applying an insulation test voltage 8 V RMS for second.. Common transient immunity in a Logic High level is the maximum tolerable (positive) dv CM /dt on the rising edge of the common mode pulse, V CM, to assure that the output will remain in a Logic High state (i.e., > 2. V). Common mode transient immunity in a Logic Low level is the maximum tolerable (negative) dv CM /dt on the falling edge of the common mode pulse signal, V CM to assure that the output will remain in a Logic Low state (i.e., <.8 V).. The.9 k load represents TTL unit load of.6 ma and the.6 k pull-up resistor. 6. The frequency at which the ac output voltage is db below its mid-frequency value. 7. Use of a. μf bypass capacitor connected between pins and 6 is recommended. 8. Pulse Width Distortion (PWD) is defined as t PHL - t PLH for any given device. 9. The difference between t PLH and t PHL between any two parts under the same test condition. 2, 6

7 IO - OUTPUT CURRENT - ma 2 2 V CC =.V T A = 2 C 2 VO - OUTPUT VOLTAGE - V Figure. DC and Pulsed Transfer Characteristics. ma ma ma 2mA 2mA ma ma IF=mA NORMALIZED CURRENT TRANSFER RATIO Normalized IF = ma VO =.V VCC = V T A = 2 C. IF - INPUT CURRENT - ma Figure 2. Current Transfer Ratio vs Input Current IF - FORWARD CURRENT - ma.. + V F I F VF - FORWARD VOLTAGE - V Figure. Input Current vs Forward Voltage T A = 2 C NORMALIZED CURRENT TRANSFER RATIO Normalized I F= ma, =.V V CC =.V T A = 2 C T A - TEMPERATURE - C Figure. Current Transfer Ratio vs Temperature TP - PROPOGATION DELAY - μs Vcc=V Vcc=V T A - TEMPERATURE - C Figure. Propagation Delay vs Temperature I F =ma, R L =.9k C L =pf TP - PROPOGATION DELAY - μs Vcc=V Vcc=2V T A - TEMPERATURE - C Figure 6. Propagation Delay vs Temperature I F =ma, R L =2k C L =pf 7

8 Tp - PROPOGATION DELAY - μs Vcc=V Vcc=V I F =ma, T A =2 C C L =pf. T. PLH. T. PHL R L - LOAD RESISTANCE - kω R L - LOAD RESISTANCE - kω Tp - PROPOGATION DELAY - μs 2.. Vcc=V Vcc=2V I F =ma, T A =2 C C L =pf Figure 7. Propagation Delay Time vs Load Resistance Figure 8. Propagation Delay Time vs Load Resistance TP - PROPAGATION DELAY - μs R L =.9K, C L =pf, T A =2 C V CC = V V CC = V 2 6 I F - INPUT CURRENT - ma Figure 9. Propagation Delay Time vs Input Current TP - PROPAGATION DELAY - μs R L =2K, C L =pf, T A =2 C V CC = V V CC = 2V 2 6 I F - INPUT CURRENT - ma Figure. Propagation Delay Time vs Input Current IOH - LOGIC HIGH OUTPUT - na... I F = ma V CC = T A = 2 C T A = 2 C T A = - C V CC - SUPPLY VOLTAGE - V Figure. Logic High Output Current vs Supply Voltage IOH - LOGIC HIGH OUTPUT CURRENT - na I F =ma V CC = =V T A - TEMPERATURE - C Figure 2. Logic High Output Current vs Temperature 8

9 I F PULSE GEN. Z O = Ω t r = ns I F 6 + V V % DUTY CYCLE /f μs R L t PHL. V. V L t PLH I F MONITOR Ω.μF C L = p Figure. Switching Test Circuit V CM V V t r % t r, t f = 8 ns 9% 9% % tf I F B A 6 R L V C SWITCH AT A: I = ma F V V FF.μF SWITCH AT B: I = ma F L V CM + - PULSE GEN. Figure. Test Circuit for Transient Immunity and Typical Waveforms. For product information and a complete list of distributors, please go to our web site: Avago, Avago Technologies, the A logo and R 2 Coupler are trademarks of Avago Technologies in the United States and other countries. Data subject to change. Copyright 2-2 Avago Technologies. All rights reserved. Obsoletes AV-8EN AV2-6EN - December, 2

ACPL-M43T Automotive Wide Operating Temperature 1MBd Digital Optocoupler in a 5-Pin Surface Mount Plastic Package. Features. Applications.

ACPL-M43T Automotive Wide Operating Temperature MBd Digital Optocoupler in a -Pin Surface Mount Plastic Package Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available;