XDS Pro-4 Network Data Sheet

Transcription

1 XDS Pr-4 Netwrk Data Sheet In the XDS Quickstart Guide that fllws this page, references are made t the netwrk cnfiguratin data sheet. Please use this dcument fr that purpse. C-Band Satellite: SES Wrld Skies 8 (AMC-8) 139 degrees West Lngitude Transpnder: 21 Dwnlink is Vertically plarized L-band receive frequency: khz Symbl Rate: sps Affiliate Web Site: (T set up receiver prgram schedule, map relay prts, and ther features) FOR TECHNICAL ASSISTANCE: FNN Supprt help@fnnnline.net 3. FNN Phne: (888) , ptin 2 (Business hurs) 4. Premiere Netwrk Operatins (818) (24/7) Rev. 6/2015 FNNXDSDataSheet.dcx

2 X-Digital Systems XDS-PRO receiver QUICK START GUIDE REVIEW THIS GUIDE IN ITS ENTIRETY BEFORE INSTALLING YOUR XDS RECEIVER. ALSO, FOLLOW THESE INSTRUCTIONS BEFORE CALLING SUPPORT. Yur receiver will NOT receive netwrk prgramming, until yu cnnect yur XDS receiver t the internet and Activate it per the instructins in this dcument. Yur XDS receiver MUST be cnnected t the internet AT ALL TIMES. XDS urges statins t use an Uninterruptible Pwer Supply (UPS) fr the XDS receiver fr equipment prtectin frm pwer spikes r brwnuts. Als cnsider lightning prtectin if yu are lcated in an area susceptible t frequent lightning strms. Surge suppressrs d nt prvide sufficient prtectin. NOTE: Use the included Netwrk Cnfiguratin Data Sheet t prperly activate yur receiver n the desired netwrk. NOTE: Appendix A cntains a frnt panel menu map that can help yu navigate thrugh the XDS receiver settings and cnfiguratin. 1. MAKING THE CONNECTIONS Satellite RF, data (LAN/WAN) and audi must be prperly cnnected. Please fllw the steps belw: 1.1 SATELLITE RF CONNECTION Yur XDS receiver is pre-tuned t yu netwrk s carrier as specified in the attached Netwrk Cnfiguratin Data Sheet. Once the satellite RF is prperly cnnected and yu apply AC pwer, the XDS receiver shuld autmatically tune and lck t the netwrk s carrier. A. Cnnect the satellite RF t yur dwnlink 1226 R XDS Pr Quick Start Guide 1/11/2010 Rev H Page 1 f 11

3 Yur new XDS receiver may include a parts kit that includes tw 6-ft RG-6 cables and an L-band splitter that allws DC pwer t pass thrugh ne prt. B. Verify the XDS receiver is tuned and lcked t the carrier Once the satellite RF is prperly cnnected, apply AC pwer t the receiver and verify as fllws: If the SIGNAL LED is green, the receiver is lcked t the carrier and the LCD screen will display: (Netwrk Lg) EB ##.# AG ### (# = numerical value) EB shuld be abve 7 and AG shuld be between abut 40 and 70 fr prper peratin. If the XDS receiver des nt acquire the netwrk carrier, the red FAULT LED will illuminate steadily and the LCD screen will display: (Netwrk Lg) EB._ AG ### (# = numerical value) Verify prper RF cnnectins and the XDS receiver shuld autmatically lck t the carrier. T manually tune the XDS receiver t a netwrk carrier: At the main screen with the netwrk lg, press the SET key, then the left r right arrw keys t reach. Press SET. Press the left r right arrw keys t reach Tuner. Press SET. Press the left r right arrw keys t reach Frequency. Press SET. Use the fur arrw keys and the SET key t set the frequency t the value n the Netwrk Data Sheet packed with yur receiver. Press the left r right arrw keys t reach Symbl Rate. Press SET. Use the fur arrw keys and the SET key t set the symbl rate t the value n the Netwrk Data Sheet packed with yur receiver. The XDSPRO receiver shuld lck. (Green SIGNAL LED will illuminate steadily) R XDS Pr Quick Start Guide 1/11/2010 Rev H Page 2 f 11

4 If this XDS receiver is designated t supply DC pwer t the LNB at yur dish, yu can turn n the LNB vltage n the XDS receiver frnt panel menu as fllws: Make sure yur dwnlink LNB is cnnected t the XDS receiver Apply AC pwer t the receiver Frm the main screen with the netwrk lg, press the SET key, then press the left r right arrws t reach. Press SET. Press the left r right arrws t reach Tuner. Press SET. Press the left r right arrws t reach LNBV, Press SET and turn the LNB Vltage n. If the frnt panel f yur XDS receiver displays flashing red lights, this indicates all Activatin and Installatin steps have nt been cmpleted and/r yur XDS receiver is nt cnnected t the internet. All Activatin and Installatin steps, including yur internet cnnectin, must be cmpleted r yu will NOT receive the netwrk s prgramming. Yur XDS receiver must be cnnected t the internet at all times. 1.2 INTERNET CONNECTION - REQUIRED This new XDS receiver requires cnnectin t an always-n internet pathway. The internet pathway is used by the netwrk t trublesht remtely, send audi r text cntent t yur receiver s strage, send cmmercial playback schedules, retrieve asplayed lgs f cmmercials inserted by the receiver, and mre. Yur XDS receiver is delivered with a 20-ft Categry 5 data patch crd wired straight thrugh (nt crssver) fr cnnectin t yur netwrk s hub r switch. A. Cnnect the XDS Receiver t yur netwrk If yu elect t place yur XDS receiver in yur lcal netwrk inside yur firewall, cnnect yur netwrk cable t ne f the receiver s LAN prts. The receiver is set by default t btain a dynamic IP address, als called a DHCP address, frm yur netwrk s DHCP server. If there is n DHCP server r yu elect t assign a static IP address, yu can d it as fllws: Assigning a Static IP address t a LAN Prt: At the main screen with the netwrk lg, press the SET key, then the left r right arrw keys t reach. Press SET R XDS Pr Quick Start Guide 1/11/2010 Rev H Page 3 f 11

5 Press the left r right arrw keys t reach Netwrk. Press SET. The default setting fr DHCP is ON. Use the SET and arrw keys t change DHCP frm ON t OFF. Press the left r right arrw keys t g t the LAN Address menu. Press SET. Use the up and dwn arrw keys and the SET key t set the desired IP address. Press the left r right arrw keys t g t the LAN Subnet menu. Press SET. Use the up and dwn arrw keys and the SET key t set the desired subnet address. Press the left and right arrws t g t the Gateway menu and press SET. Use the up and dwn arrw keys and the SET key t set the desired gateway address. Assigning a Static IP address t the WAN Prt: If yu elect t cnnect yur receiver in a firewall zne called a DMZ (demilitarized zne) r Outside the firewall where it can see the internet directly, cnnect yur netwrk cable t the receiver s WAN prt. Yu must assign a static IP WAN Address, WAN Subnet, and Gateway. Fllw the Assigning a Static IP address t a LAN Prt instructins abve t g t the apprpriate WAN menus and change settings as desired. NOTE: If yur lcal area netwrk (LAN) requires the use f a prxy server, please refer t the nline user s guide lcated at yur affiliate s website. Refer t Sectin 2 n page 7 f this dcument fr instructins n hw t lgin t yur receiver s website at yur netwrk s hub. B. Test cnnectin t the netwrks NOC At the main screen with the netwrk lg, press the SET key, then the left r right arrw keys t reach. Press SET. Press the left r right arrw keys t reach Netwrk. Press SET. Press the left r right arrw keys t TEST NOC. Press SET. Press the NOC sft key t perfrm the test. The test will take a minute r tw. Yu will get a SUCCESFULLY CONNECTED TO NOC message if yur IP settings are crrect. Otherwise yu will get a CANNOT CONNECT TO NOC message and yu will need t adjust yur IP settings (n the receiver, r in yur netwrk s switches, ruters r firewall) until the receiver can cnnect t the NOC. T trublesht, yu can use the PING sft key t verify yur receiver can lcally cnnect t yur netwrk gateway R XDS Pr Quick Start Guide 1/11/2010 Rev H Page 4 f 11

6 1.3 AUDIO OUTPUT CONNECTIONS Once the XDS receiver is lcked t the carrier yu can verify audi functinality as fllws: A. Verify audi receptin Initially the XDS receiver headphne utput and all the audi prts are prgrammed t receive the netwrk s Test Channel. Cnnect a set f headphnes and verify yu can hear the Test Channel. T manually prgram the XDS receiver headphne t utput the Test Channel: At the main screen with the netwrk lg, press the SET key, then the left r right arrws t reach Audi Prts. Press SET. Press the left r right arrws t reach Headphnes. Press SET. Press the left r right arrws t reach Prgram. Press SET. Use the up and dwn arrws t find the netwrk s Test Channel. Press SET. The Test Channel is intended t check receiver peratin. It des NOT prve that yu can receive the netwrk s prgramming. T receive prgram audi, yu must cmplete all installatin and Activatin steps, including a fulltime internet cnnectin. Yur XDS receiver must be cnnected t the internet at all times. B. Verify audi prts Yur new XDS receiver may be delivered with a parts kit including fur mating DB-9 cnnectrs with shells. The analg audi utputs fr yur services appear at the fur DB-9 cnnectrs n the rear panel. Wiring pinuts are the same as n the lder Starguide receivers: AUDIO OUTPUT DB9M Pin Signal Signal Pin 1 L+ L- 6 2 GND GND GND R- 9 5 R R XDS Pr Quick Start Guide 1/11/2010 Rev H Page 5 f 11

7 Each DB-9 cnnectr nrmally carries ne radi prgram stream, either mn r stere. If the prgram is mn, the same audi appears n the left and right pin pairs. In a few, rare cases, the left and right halves f a stere channel may be used fr unrelated mn prgrams, but this is n lnger the nrm. Yur receiver shuld be pre-cnfigured t utput the Test Channel n all prts. Verify yu can hear the test prgram thrugh all receiver prts. T manually prgram the XDS receiver t utput the Test Channel n a desired audi prt: At the main screen with the netwrk lg, press the SET key, then the left r right arrws t reach Audi Prts. Press SET. Press the left r right arrws t select the Audi Prt (letter A, B, C r D). Press SET. Press the left r right arrws t select Prgram. Press SET. Use the up and dwn arrws t find the Test Channel. Press SET. 1.4 RELAY CLOSURES There are tw DB-37 cnnectrs n the rear panel which tgether cntain a ttal f 32 mappable relay (r cntact) clsures t drive yur statin autmatin. Relay clsure are mmentary Frm A, rated Yur XDS receiver may be delivered with a parts kit including tw mating DB-37 cnnectrs with shells R XDS Pr Quick Start Guide 1/11/2010 Rev H Page 6 f 11

8 The pinuts fr the DB-37 cnnectrs are: RELAY A - DB37M RELAY B - DB37M Pin Signal Signal Pin Pin Signal Signal Pin 1 RLY1A RLY1B 20 1 RLY1A RLY1B 20 2 RLY2A RLY2B 21 2 RLY2A RLY2B 21 3 RLY3A RLY3B 22 3 RLY3A RLY3B 22 4 RLY4A RLY4B 23 4 RLY4A RLY4B 23 5 GND GND 24 5 GND GND 24 6 RLY5A RLY5B 25 6 RLY5A RLY5B 25 7 RLY6A RLY6B 26 7 RLY6A RLY6B 26 8 RLY7A RLY7B 27 8 RLY7A RLY7B 27 9 RLY8A RLY8B 28 9 RLY8A RLY8B GND RLY9B GND RLY9B RLY9A RLY10B RLY9A RLY10B RLY10A RLY11B RLY10A RLY11B RLY11A RLY12B RLY11A RLY12B RLY12A GND RLY12A GND Cue Txd RLY13B NC RLY13B RLY13A RLY14B RLY13A RLY14B RLY14A RLY15B RLY14A RLY15B RLY15A RLY16B RLY15A RLY16B RLY16A 19 RLY16A If yu r yur autmatin vendr has develped a prgram that can read text cues directly, yu may get the cue serial stream frm pins 15 and 10 n the Relay A prt n yur XDS receiver (see pinut abve). The Cue TxD pin is RS-232 data with n flw cntrl r handshaking. Baud rate is set by default t 9600 bps 8N1. 2. VERIFY PROGRAMMING AND ACTIVATE In the XDS system each prgram, nt each channel, is permissined and labeled fr statin use. Therefre, instead f tuning t a channel t find a prgram, yu will schedule the prgrams t appear n each utput prt. Yu will need t review yur schedule and activate yur receiver with yur statin s prgramming. Initially yur receiver nly utputs the Test Channel n all prts, the frnt panel LCD shws a Please Activate message and the range UPDATE LED in flashing R XDS Pr Quick Start Guide 1/11/2010 Rev H Page 7 f 11

9 Yu must edit and activate the schedule f the prgrams that yu want t appear n each audi utput prt f the XDS receiver thrugh the netwrk s Affiliate website at the internet URL prvided n the Netwrk Cnfiguratin Data Sheet packed with yur receiver. T lgin yu will use the XDS receiver s serial number as the username and a passwrd generated by the receiver. T find this passwrd: At the main screen with the netwrk lg, press the SET key, then the left r right arrws t reach. Press SET. Press the left r right arrws t select Serial Number. Press the PWD sft key t display yur passwrd. Once lgged in, yu may setup a friendly passwrd t the site and als review and apprve yur receiver s setup (Time Zne, Schedule, Relay Mappings, etc). Adjust Time Zne the apprpriate time zne fr yur receiver Review Schedule Yu will see the default schedule fr every statin yur receiver supprts. Please mdify and verify yur schedule as desired. RULE: Each call-letter radi statin at yur site that carries any prgramming r cmmercials frm this XDS receiver must be assigned t an XDS receiver prt and each prt must be scheduled t utput the prgrams yu need. NOTE: Yur new XDS receiver cntains abut 32 hurs f audi strage which yu may use t tape delay netwrk prgrams and schedule them t play later. Yu can schedule the same XDS receiver prt t play back a mixed schedule f live and delayed prgrams. Review Relay Mappings Yu will see the default relay mapping cnfiguratin fr yur receiver. Please mdify and verify yur mappings as desired. Apprve and Activate Once yu reviewed all yur desired settings, press the UPDATE buttn, and the NOC will send the updated prgramming t yur receiver. It may take a cuple f minutes fr the XDS receiver t dwnlad the netwrk s prgramming infrmatin. T verify yur receiver is activated, the UPDATE LED will 1226 R XDS Pr Quick Start Guide 1/11/2010 Rev H Page 8 f 11

10 turn ff and the frnt panel LCD will display the XDSPRO message instead f the Please Activate message 3. SUPPORT CONTACT INFORMATION If yu have any prblems please call the netwrk s Technical Services ffices specified in the Netwrk Cnfiguratin Datasheet and they will help yu set up and verify yur receiver. 4. FULL MANUAL This Quick Start Guide is nt intended t be a full equipment manual. T view r dwnlad the XDS User s Guide fr yur receiver, please brwse t the URL n the Netwrk Data Sheet packed with yur receiver. Yu dn t need t lg in. Pint t Help, then t User s Guide. The User s Guide and Data Sheet may change frm time t time, r when sftware features change R XDS Pr Quick Start Guide 1/11/2010 Rev H Page 9 f 11

11 APPENDIX A XDS RECEIVER MENU MAP EB AG XDS PRO4 U/D U/D Active Faults OK Fault Histry Envirnment Temp: 39 C Fan: HIGH XDS PRO4 Status Strage Status Ttal: 3884MB Avail: 3683 MB Pwer Status 1.2V= V=5.09 U/D XDS PRO4 Serial Number XDSP M&C Prts 115K,8,Nne,1 Netwrk Alarms 0FFBDFFF Tuner Relays Factry Defaults Versin U/D Netwrk DHCP Netwrk Netwrk LAN Address LAN Subnet Netwrk WAN Address Netwrk Test NOC Netwrk Gateway Netwrk WAN Subnet Frequency Symbl Rate FEC LNB Pwer XDS PRO4 Audi Prt U/D U/D Audi Prt A Audi Prt B Audi Prt C Headphnes Audi Prt D Audi Prt # Prgram Audi Prt # Audi Prt # Spt Settings Audi Prt # Statin 1226 R XDS Pr Quick Start Guide 1/11/2010 Rev H Page 10 f 11

12 Imprtant Ntice Users Manual The XDS-PRO4 DVB Satellite Receiver Users Manual is available n-line. T access the Manual, please lg-n t the netwrk s affiliate website with yur Affiliate s web page access infrmatin, g t Help, and select: Users Manual. If yu have any questins, please cntact yur Affiliate Statin, r the Help Desk. FCC Cmpliance THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION OF THIS DEVICE IS SUBJECT TO THE FOLLOWING TWO CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE; AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION. UL and CSA Cmpliance THE XDS-PRO4 DVB SATELLITE RECEIVER WAS TESTED ACCORDING TO UL :2003 AND CSA C22.2 NO :2003. THIS DEVICE MEETS THE SAFETY AND TEST REQUIREMENTS OF THE TEST SPECIFICATIONS, AND WAS FOUND TO BE IN COMPLIANCE WITH PROTECTION AIMS OF THE APPLICABLE EC-DIRECTIVES AND THE REQUIREMENTS OF THE STANDARDS. THE XDS-PRO4 DVB SATELLITE RECEIVER MAY BE MARKED WITH THE TUV MARK AS SHOWN BELOW; CERTIFICATE NO. U Warning! Apprved external telecm pwer crss prtectin must be incrprated int the final installatin in accrdance with Annex NAC f UL/CSA standard Failure t cmply may result in a fire r electric shck hazard and will vid regulatry cmpliance certificatin. Acknwledge f Trademarks Any prduct r crprate names used herein may be trademarks r registered trademarks, and are nly used fr identificatin and explanatin, withut intent t infringe. Any terms mentined r used that are knwn trademarks r service marks have been apprpriately capitalized and italicized. X-Digital Systems, Inc. cannt attest t the accuracy f this infrmatin. Use f a term in this dcument shuld nt be regarded as affecting the validity f any trademark r service mark. Patent Pending X-Digital Systems, Inc., DVB Satellite Receiver Patents Pending Disclaimer This dcument is intended t prvide infrmatin abut the XDS-PRO4 DVB Satellite Receiver. Every effrt has been made t make this dcument as cmplete and accurate as pssible, but n warranty r fitness is implied. The infrmatin is prvided n an as is basis and X-Digital Systems shall have neither liability nr respnsibility t any persn r entity with respect t any lss r damages arising frm the infrmatin cntained in this dcument. Warning! Apprved external telecm pwer crss prtectin must be incrprated int the final installatin in accrdance with Annex NAC f UL/CSA standard Failure t cmply may result in a fire r electric shck hazard and will vid regulatry cmpliance certificatin R XDS Pr Quick Start Guide 1/11/2010 Rev H Page 11 f 11