BIPOLAR DIGITAL INTEGRATED CIRCUITS

Transcription

1 DATA SHEET BIPOLAR DIGITAL INTEGRATED CIRCUITS PPB506GV, PPB507GV 3GHz INPUT DIVIDE BY 56, 8, 64 PRESCALER IC FOR ANALOG DBS TUNERS The PPB506GV and PPB507GV are 3.0 GHz input, high division silicon prescaler ICs for analog DBS tuner applications. These ICs divide-by-56, 8 and 64 contribute to produce analog DBS tuners with kit-use of 7 K series DTS controller or standard CMOS PLL synthesizer IC. The PPB506GV/PPB507GV are shrink package versions of the PPB586G/588G or PPB505GR so that these smaller packages contribute to reduce the mounting space replacing from conventional ICs. The PPB506GV and PPB507GV are manufactured using NEC s high ft NESAT IV silicon bipolar process. This process uses silicon nitride passivation film and gold electrodes. These materials can protect chip surface from external pollution and prevent corrosion/migration. Thus, these ICs have excellent performance, uniformity and reliability. FEATURES x High toggle frequency : fin = 0.5 GHz to 3.0 GHz x High-density surface mounting : 8-pin plastic SSOP (75 mil) x Low current consumption : 5 V, 9 ma x Selectable high division : y56, y8, y64 x Pin connection variation : PPB506GV and PPB507GV APPLICATION These ICs can use as a prescaler between local oscillator and PLL frequency synthesizer included modulus prescaler. For example, following application can be chosen; x x Analog DBS tuner s synthesizer Analog CATV converter synthesizer ORDERING INFORMATION PART NUMBER PACKAGE MARKING SUPPLYING FORM PPB506GV-E 8-pin plastic 506 Embossed tape 8 mm wide. Pin is in tape pull-out PPB507GV-E SSOP (75 mil) 507 direction. 000 p/reel. Remarks To order evaluation samples, please contact your local NEC sales office. (Part number for sample order: PPB506GV, PPB507GV) Caution: Electro-static sensitive devices Document No. P0767EJ3V0DS00 (3rd edition) Date Published January 998 N CP(K) Printed in Japan 996

2 PIN CONNECTION (Top View) 8 Pin NO. PPB506GV PPB507GV SW IN IN VCC 3 IN SW 4 GND OUT 5 NC GND 6 SW SW 7 OUT NC 8 VCC IN PRODUCT LINE-UP Features Part No. ICC fin VCC Package Pin connection (division, Freq.) (ma) (GHz) (V) y5, y56,.5 GHz PPB586G to to pin SOP 5 mil NEC original y8, y64,.5 GHz PPB588G to to 5.5 y56, y8, y64 PPB505GR to to 5.5 Standard 3.0 GHz PPB506GV to to pin SSOP 75 mil NEC original PPB507GV to to 5.5 Standard Remarks x This table shows the TYP values of main parameters. Please refer to ELECTRICAL CHARACTERISTICS. x PPB586G and PPB588G are discontinued. INTERNAL BLOCK DIAGRAM D D D D D IN CLK CLK CLK CLK CLK IN CLK D D D CLK CLK CLK OUT AMP SW SW

3 SYSTEM APPLICATION EXAMPLE RF unit block of Analog DBS tuners stif input from DBS converter To 50 MHz MIX BPF SAW AGC amp. FM demo. Baseband output OSC To 650 MHz High division prescaler µ PB506GV or µ PB507GV CMOS PLL synthesizer LPF loop filter RF unit block of Analog CATV converter To 800 MHz BPF upconverter BPF downconverter To 300 MHz OSC To 000 MHz High division prescaler µ PB506GV or µ PB507GV CMOS PLL synthesizer LPF loop filter 3

4 PIN EXPLANATION Pin name Applied voltage V Pin voltage V Functions and explanation PPB506GV Pin no. PPB507GV IN.9 Signal input pin. This pin should be coupled to signal source with capacitor (e.g. 000 pf) for DC cut. IN.9 Signal input bypass pin. This pin must be equipped with bypass capacitor (e.g. 000 pf) to minimize ground impedance. GND 0 Ground pin. Ground pattern on the board should be formed as wide as possible to minimize ground impedance. SW H/L Divide ratio input pin. The ratio can be determined by following applied level to these pins SW H L SW SW H y64 y8 L y8 y These pins should be equipped with bypass capacitor (e.g. 000 pf) to minimize ground impedance. VCC 4.5 to 5.5 Power supply pin. This pin must be equipped with bypass capacitor (e.g pf) to minimize ground impedance. OUT.6 to 4.7 Divided frequency output pin. This pin is designed as emitter follower output. This pin can be connected to CMOS input due to. VP-P MIN output NC Non connection pin. This pin must be openned

5 ABSOLUTE MAXIMUM RATINGS PARAMETER SYMBOL CONDITION RATINGS UNIT Supply voltage VCC TA = +5 qc ð0.5 to +6.0 V Input voltage Vin TA = +5 qc ð0.5 to VCC V Total power dissipation PD Mounted on double sided copper clad 50 u 50 u.6 mm epoxy glass PWB (TA = +85 qc) 50 mw Operating ambient temperature TA ð40 to +85 qc Storage temperature Tstg ð55 to +50 qc RECOMMENDED OPERATING CONDITIONS PARAMETER SYMBOL MIN. TYP. MAX. UNIT NOTICE Supply voltage VCC V Operating ambient temperature TA ð qc ELECTRICAL CHARACTERISTICS (TA = ð40 to +85 qc, VCC = 4.5 to 5.5 V, ZS = 50 :) PARAMETER SYMBOL TEST CONDITION MIN. TYP. MAX. UNIT Circuit current ICC No signals ma Upper limit operating frequency fin(u) Pin = ð5 to +6 dbm 3.0 GHz Lower limit operating frequency fin(l) Pin = ð0 to +6 dbm 0.5 GHz Lower limit operating frequency fin(l) Pin = ð5 to +6 dbm.0 GHz Input power Pin fin =.0 to 3.0 GHz ð5 +6 dbm Input power Pin fin = 0.5 to.0 GHz ð0 +6 dbm Output Voltage Vout CL = 8 pf..6 VP-P Divide ratio control input high VIH Connection in the test circuit VCC VCC VCC Divide ratio control input low VIL Connection in the test circuit OPEN or GND OPEN or GND OPEN or GND Divide ratio control input high VIH Connection in the test circuit VCC VCC VCC Divide ratio control input low VIL Connection in the test circuit OPEN or GND OPEN or GND OPEN or GND 5

6 TYPICAL CHARACTERISTICS (Unless otherwise specified TA = +5 qc) 5 0 CIRCUIT CURRENT vs. SUPPLY VOLTAGE No signals TA = +85 C ICC - Circuit Current - ma 5 0 TA = +5 C TA = 40 C VCC - Supply Voltage - V Divide by 64 mode +0 INPUT POWER vs. INPUT FREUENCY TA = +5 C +0 INPUT POWER vs. INPUT FREUENCY VCC = 4.5 to 5.5 V Pin - Input Power - dbm VCC = 4.5 to 5.5 V Guaranteed Operating Window VCC = 4.5 to 5.5 V Pin - Input Power - dbm TA = 40 C TA = +85 C TA = +5 C Guaranteed Operating Window TA = +85 C TA = +5 C TA = 40 C OUTPUT VOLTAGE vs.input FREUENCY TA = +5 C Pin = 0 dbm.0.8 OUTPUT VOLTAGE vs.input FREUENCY TA = 40 C Pin = 0 dbm Vout - Output Voltage - VP-P VCC = 5.5 V VCC = 4.5 V Vout - Output Voltage - VP-P VCC = 4.5 V VCC = 5.5 V

7 Vout - Output Voltage - VP-P OUTPUT VOLTAGE vs. INPUT RFEUENCY TA = +85 C Pin = 0 dbm VCC = 4.5 V VCC = 5.5 V Divide by 8 mode +0 INPUT POWER vs. INPUT FREUENCY TA = +5 C +0 INPUT POWER vs. INPUT FREUENCY VCC = 4.5 to 5.5 V Pin - Input Power - dbm VCC = 4.5 to 5.5 V Guaranteed Operating Window VCC = 4.5 to 5.5 V Pin - Input Power - dbm TA = 40 C TA = +85 C TA = +5 C Guaranteed Operating Window TA = +85 C TA = +5 C TA = 40 C OUTPUT VOLTAGE vs. INPUT FREUENCY TA = +5 C Pin = 0 dbm.0.9 OUTPUT VOLTAGE vs. INPUT FREUENCY TA = 40 C Pin = 0 dbm Vout - Output Voltage - VP-P VCC = 5.5 V VCC = 4.5 V Vout - Output Voltage - VP-P VCC = 5.5 V VCC = 4.5 V

8 Vout - Output-Voltage - VP-P OUTPUT VOLTAGE vs. INPUT FREUENCY TA = +85 C Pin = 0 dbm VCC = 5.5 V VCC = 4.5 V Divide by 56 mode +0 INPUT POWER vs. INPUT FREUENCY TA = +5 C +0 INPUT POWER vs. INPUT FREUENCY VCC = 4.5 to 5.5 V Pin - Input Power - dbm VCC = 4.5 to 5.5 V Guaranteed Operating Window VCC = 4.5 to 5.5 V Pin - Input Power - dbm TA = 40 C TA = +85 C TA = +5 C Guaranteed Operating Window TA = +85 C TA = +5 C TA = 40 C OUTPUT VOLTAGE vs. INPUT FREUENCY TA = +5 C Pin = 0 dbm.0.9 OUTPUT VOLTAGE vs. INPUT FREUENCY TA = 40 C Pin = 0 dbm Vout - Output Voltage - VP-P VCC = 5.5 V VCC = 4.5 V Vout - Output Voltage - VP-P VCC = 5.5 V VCC = 4.5 V

9 Vout - Output Voltage - VP-P OUTPUT VOLTAGE vs. INPUT FREUENCY TA = +85 C Pin = 0 dbm VCC = 5.5 V VCC = 4.5 V PPB506GV S vs. INPUT FREUENCY C S Z REF.0 Units munits/ Ω Ω hp MARKER 3.0 GHz D : 500 MHz : 000 MHz 3 : 000 MHz 4 : 3000 MHz START STOP GHz GHz 4 FREUENCY S MHz MAG ANG

10 PPB506GV S vs. OUTPUT FREUENCY Divide by 64 mode, C S Z REF.0 Units 00.0 munits/ 7. Ω Ω hp MARKER 45.0 MHz D : 45 MHz : 00 MHz FREUENCY S MHz MAG ANG START STOP GHz GHz PPB506GV S vs. OUTPUT FREUENCY Divide by 8 mode, C S Z REF.0 Units 00.0 munits/ 9.34 Ω Ω hp MARKER 45.0 MHz D : 45 MHz : 00 MHz FREUENCY S MHz MAG ANG START STOP GHz GHz 0

11 PPB506GV S vs. OUTPUT FREUENCY Divide by 56 mode, C S Z REF.0 Units 00.0 munits/ 99.5 Ω Ω hp MARKER 45.0 MHz D : 45 MHz : 00 MHz FREUENCY S MHz MAG ANG START STOP GHz GHz PPB507GV S vs. INPUT FREUENCY C S Z REF.0 Units munits/ 38. Ω Ω hp MARKER GHz D : 500 MHz 4 : 000 MHz 3 : 000 MHz : 3000 MHz START STOP GHz GHz 4 FREUENCY S MHz MAG ANG

12 PPB507GV S vs. OUTPUT FREUENCY Divide by 64 mode, C S Z REF.0 Units 00.0 munits/ 85.3 Ω Ω hp MARKER 45.0 MHz D : 45 MHz : 00 MHz FREUENCY S MHz MAG ANG START STOP GHz GHz PPB507GV S vs. OUTPUT FREUENCY Divide by 8 mode, C S Z REF.0 Units 00.0 munits/ 85.0 Ω Ω hp MARKER 45.0 MHz D : 45 MHz : 00 MHz FREUENCY S MHz MAG ANG START STOP GHz GHz

13 PPB507GV S vs. OUTPUT FREUENCY Divide by 56 mode, C S Z REF.0 Units 00.0 munits/ Ω 7.8 Ω hp MARKER 45.0 MHz D : 45 MHz : 00 MHz FREUENCY S MHz MAG ANG START STOP GHz GHz 3

14 TEST CIRCUIT PPB506GV S.G 50 Ω C C C3 3 SW IN IN VCC OUT SW C4 C5 C7 Stray cap. Monitor MΩ 0.6 pf Oscilloscope 4 GND NC 5 OPEN or Counter VCC = +5.0 V ±0 % 50 Ω C6 x SG (HP-8665A) Divide ratio setting x Counter (HP5350B) : To measure input sensitivity or SW Oscilloscope : To measure output voltage swing H L COMPONENT LIST PPB506GV PPB507GV SW H /64 /8 L /8 /56 H: Connect to VCC L: Connect to GND or OPEN C to C5 000 pf 000 pf C pf pf Stray cap. Aprox 4 pf Aprox 5 pf C7 3.5 pf*.5 pf* * Capacitance CL = 8 pf for DUT includes C7 value + stray capacitance on the board and measurement equipment. 4

15 TEST CIRCUIT PPB507GV 50 Ω C IN IN 8 C3 S.G VCC NC 7 OPEN C 3 SW SW 6 C4 C5 4 OUT GND 5 VCC = +5.0 V ±0% C6 MΩ Monitor 0.6 pf C7 Stray cap. Oscilloscope or Counter 50 Ω x SG (HP-8665A) Divide ratio setting x Counter (HP5350B) : To measure input sensitivity or SW Oscilloscope : To measure output voltage swing H L SW H /64 /8 L /8 /56 H: Connect to VCC L: Connect to GND or OPEN 5

16 C C7 C3 PPB506GV, PPB507GV ILLUSTRATION OF THE TEST CIRCUIT ASSEMBLED ON EVALUATION BOARD PPB506GV P SW VCC IN C C6 OUT IN C C5 C7 OUT C4 SW µ PB506/08/09GV OPEN PPB507GV IN IN P C6 C3 VCC SW C C4 SW C5 OUT OUT µ PB507GV EVALUATION BOARD CHARACTERS () 35 Pm thick double-sided copper clad 50 u 50 u 0.4 mm polyimide board () Back side: GND pattern (3) Solder plated patterns (4) q : Through holes 6

17 PACKAGE DIMENSIONS 8 PIN PLASTIC SSOP (UNIT: mm) (75 mil) 8 5 detail of lead end ± MAX. 3. ± ±0..8 MAX. 0.±0..5 ± MAX ± M 0.5 7

18 NOTE CORRECT USE () Observe precautions for handling because of electro-static sensitive devices. () Form a ground pattern as wide as possible to minimize ground impedance (to prevent undesired operation). (3) Keep the wiring length of the ground pins as short as possible. (4) Connect a bypass capacitor (e.g pf) to the VCC pin. RECOMMENDED SOLDERING CONDITIONS This product should be soldered in the following recommended conditions. Other soldering methods and conditions than the recommended conditions are to be consulted with our sales representatives. PPB506GV, PPB507GV Soldering method Soldering conditions Recommended condition symbol Infrared ray reflow VPS Wave soldering Pin part heating Package peak temperature: 35 qc, Hour: within 30 s. (more than 0 qc), Time: 3 times, Limited days: no.* Package peak temperature: 5 qc, Hour: within 40 s. (more than 00 qc), Time: 3 times, Limited days: no.* Soldering tub temperature: less than 60 qc, Hour: within 0 s., Time: time, Limited days: no. Pin area temperature: less than 300 qc, Hour: within 3 s./pin, Limited days: no.* IR VP WS * It is the storage days after opening a dry pack, the storage conditions are 5 qc, less than 65 % RH. Caution The combined use of soldering method is to be avoided (However, except the pin area heating method). For details of recommended soldering conditions for surface mounting, refer to information document SEMICONDUCTOR DEVICE MOUNTING TECHNOLOGY MANUAL (C0535E). 8

19 [MEMO] 9

20 ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC SENSITIVE DEVICES No part of this document may be copied or reproduced in any form or by any means without the prior written consent of NEC Corporation. NEC Corporation assumes no responsibility for any errors which may appear in this document. NEC Corporation does not assume any liability for infringement of patents, copyrights or other intellectual property rights of third parties by or arising from use of a device described herein or any other liability arising from use of such device. No license, either express, implied or otherwise, is granted under any patents, copyrights or other intellectual property rights of NEC Corporation or others. While NEC Corporation has been making continuous effort to enhance the reliability of its semiconductor devices, the possibility of defects cannot be eliminated entirely. To minimize risks of damage or injury to persons or property arising from a defect in an NEC semiconductor device, customers must incorporate sufficient safety measures in its design, such as redundancy, fire-containment, and anti-failure features. NEC devices are classified into the following three quality grades: "Standard", "Special", and "Specific". The Specific quality grade applies only to devices developed based on a customer designated "quality assurance program" for a specific application. The recommended applications of a device depend on its quality grade, as indicated below. Customers must check the quality grade of each device before using it in a particular application. Standard: Computers, office equipment, communications equipment, test and measurement equipment, audio and visual equipment, home electronic appliances, machine tools, personal electronic equipment and industrial robots Special: Transportation equipment (automobiles, trains, ships, etc.), traffic control systems, anti-disaster systems, anti-crime systems, safety equipment and medical equipment (not specifically designed for life support) Specific: Aircrafts, aerospace equipment, submersible repeaters, nuclear reactor control systems, life support systems or medical equipment for life support, etc. The quality grade of NEC devices is "Standard" unless otherwise specified in NEC's Data Sheets or Data Books. If customers intend to use NEC devices for applications other than those specified for Standard quality grade, they should contact an NEC sales representative in advance. Anti-radioactive design is not implemented in this product. M