catalogue CAR REFINISH CONSUMABLES

Transcription

1 2013 catalogue GB CAR REFINISH CONSUMABLES

2

3 Dear customers, We are glad to introduce a comprehensive range of high-quality car refinish consumables С.А.R.FIT. Traditional German quality, proven manufacturing recipes and technologies ensure perfect finish results meeting the requirements of modern applications. Among other things, the catalogue features a new С.А.R.FIT product series BLACK LABEL, part of the unique system of new generation polyester materials for specialized applications. All materials covered in the catalogue can be used with all paint systems without compromising application technology, which is another proof of С.А.R.FIT s high quality. 1

4 Suitable substrates Brush application Cleaning Airless application viscosity Material thickness Use of measuring stick Air drying/flash-off Mixing ratio by volume: 2 components; 3 components Low baking Addition of hardener/catalyst Infrared drying (short wave) Pot life of liquid materials Orbital sander Nozzle size, mm Flat-bed sander Inlet pressure Dry sandind by hand with putty knife/pot life of the putty Wet sandind by hand Shake can well subsequent material Number of coats / material application Polishing Spray can application Keep frost protected Cartridge gun Keep out of direct sunlight UB Suction gun Attention Paint roller application See TDS 2

5 Contents Black Label Series 4 Putties 15 Clearcoats 20 Primers, Fillers 24 Thinners, Cleaners 29 Bodycoats, Cabin coats 31 Sealants 33 Ancillary material 35 Masking 36 Cloths 40 Polishing materials 42 Accessories 43 3

6 BLACK LABEL SERIES Fill&Fine Putty anticorrosion protection ANTICORROSION Two component basic universal filling putty for eliminating major and medium mechanical damages. First ever polyester putty with anticorrosive properties. Universal filling putty for eliminating car and commercial vehicle body imperfections. Due to last generation resins and modern fine fillers, this putty creates a smooth and pinhole-free surface, thus enabling the refinisher to use one product at all stages of repair (no need to use finishing putty) Due to last generation resins, sanding can be started with P150 grit abrasives, which significantly speeds up sanding and helps avoid paintwork defects (deep sanding marks) Easy to apply in thin and thick coats Does not clog the sandpaper Anticorrosive properties. All kinds of steel, flexible aluminium, OEM substrates*. VOC < 250 g/l EU limit value: 2004/42/IIB(b)(250) Articles Pcs. / pack kg, w/hardener 12 to be treated must be cleaned, dried, degreased with CF Silicone Remover and sanded * Add 2 3% BPO Hardener by weight Pot life: 3 5 min min depending on ambient temperature Standard sanding method With P Further treatment With P (intermediate sanding step of 100 grit should be observed) Recommended sanding method First with P150, then with P240 Color red 1900 g/l Flash point 31 C Storage Keep away from direct sunlight Xn Harmful 4

7 BLACK LABEL SERIES Two component polyester filling putty with a glass microsphere. Basic/filling putty for eliminating car and commercial vehicle body imperfections. Due to last generation resins, sanding can be started with P150 grit abrasives, which significantly speeds up sanding and helps avoid paintwork defects (deep sanding marks) Specific formula of the putty with hollow glass microspheres significantly reduces its density, improves its filling power and leaves light gloss on the surface until cure is complete, allowing for better control of the repair zone Excellent sandability even a few days after application Recommended for use on large body parts: roof, doors, trunk lid, bonnet, etc. All kinds of steel, fiberglass plastics, OEM substrates*. Light&Soft Putty LOW DENSITY Articles Pcs. / pack kg, w/hardener 10 VOC < 250 g/l EU limit value: 2004/42/IIB(b)(250) to be treated must be cleaned, dried, degreased with CF Silicone Remover and sanded * Add 2 3% BPO Hardener by weight Pot life: 3 5 min min depending on ambient temperature Standard sanding method With P Further treatment With P (intermediate sanding step of 100 grit should be observed) Recommended sanding method First with P150, then with P240 Color beige 1260 g/l Flash point 31 C Storage Keep away from direct sunlight Xn Harmful 5

8 BLACK LABEL SERIES Glas&Soft Putty VOC < 250 g/l EU limit value: 2004/42/IIB(b)(250) Two component fiberglass-filled polyester putty. Perfect choice for the repair of body parts with significant mechanical damages, loss of carrier function and through holes. When applied, it produces a coat of significant thickness which cures in a uniform manner. Due to its homogeneous structure and a minimum number of pinholes, makes application of finishing putties unnecessary. Fiberglass putty for eliminating car and commercial vehicle body imperfections. Due to last generation resins, sanding can be started with P150 grit abrasives, which significantly speeds up sanding and helps avoid deep sanding marks Restores the carrier function of damaged parts Easy application and uniform cure in thick coats No sandpaper clogging No need in additional processing with a finishing putty Very good adhesion to steel, galvanized steel, flexible aluminium and fiberglass plastics. All kinds of steel, flexible aluminium, fiberglass plastics, OEM substrates*. Articles Pcs. / pack kg, w/hardener 12 to be treated must be cleaned, dried, degreased with CF Silicone Remover and sanded * Add 2 3% BPO Hardener by weight Pot life: 3 5 min min depending on ambient temperature Standard sanding method With P Further treatment With P (intermediate sanding step of 100 grit should be observed) Recommended sanding method First with P150, then with P240 Color blue/green 1750 g/l Flash point 31 C Storage Keep away from direct sunlight Xn Harmful 6

9 BLACK LABEL SERIES Two-component polyester finishing putty. Due to its relatively low viscosity, the putty is easy to apply and spread with a putty knife, efficiently filling minor surface imperfections. For filling minor defects, irregularities and pinholes on car and commercial vehicle body paintworks, as well as scratches resulting from sanding with P grit abrasives. Due to its low viscosity, efficiently fills scratches resulting from sanding with P , which enables it to be directly applied onto polyester materials and other coatings sanded with P abrasives Smooth pinhole-free surface produced upon drying, together with good filling properties, saves time and subsequently applied materials Easy to apply in thin coats and process with P grit abrasives (machine sanding) which ensures a high-quality finish Drying and sanding with P grit abrasives can be followed by wet-on-wet filler application and subsequent topcoat application. Fillers, primer-fillers, OEM substrates*. Articles Pcs. / pack L, w/hardener 10 Light Violet Putty VOC < 250 g/l EU limit value: 2004/42/IIB(b)(250) to be treated must be cleaned, dried, degreased with CF Silicone Remover and sanded * Add 3-4% BPO Hardener (< 20 С) Add 2-3% BPO Hardener (> 20 С) Pot life: 5 7 min With P When applied in thicker coats, first apply a thin coat to improve adhesion and eliminate pinholes min depending on ambient temperature Further treatment Recoat with 2К fillers and/or base coats and clear coats With P Initial machine sanding of thick putty coats can be done with P180 Color violet 1250 g/l Flash point 31 C Storage Keep away from direct sunlight Keep away from direct sunlight Xn Harmful 7

10 BLACK LABEL SERIES Alu&Soft Putty VOC: < 250 g/l EU limit value: 2004/42/IIB(b)(250) Two component aluminium-filled polyester putty. It is used as a basic filling putty, particularly, in the repair of metal surfaces exposed to high temperature and mechanical abuse. For repairs on metal surfaces of cars and commercial vehicles. Due to last generation resins and modern fine fillers, this putty creates a smooth and pinhole-free surface, thus enabling the refinisher to use one product at all stages of repair (no need to use a finishing putty) Due to last generation resins, sanding can be started with P150 grit abrasives, which significantly speeds up sanding and helps avoid deep sanding marks Retains its shape in thin coats Easy to sand with Р150 grit abrasives, providing a smooth transition between the repair and the undamaged surrounding area Excellent adhesion. All kinds of steel, flexible aluminium, OEM substrates*. Articles Pcs. / pack kg, w/hardener 12 to be treated must be cleaned, dried, degreased with CF Silicone Remover and sanded * Add 2 3% BPO Hardener by weight Pot life: 3 5 min min depending on ambient temperature Standard sanding method With P Further treatment With P (intermediate sanding step of 100 grit should be observed) Recommended sanding method First with P150, then with P240 Color metallic 1780 g/l Flash point 31 C Storage Keep away from direct sunlight Xn Harmful 8

11 BLACK LABEL SERIES Fiber filled extra light 2К polyester putty for badly damaged surfaces requiring extensive repair. It has been developed for restoring damaged surfaces, increasing the mechanical strength of the repaired element. For repairs on metal surfaces of cars and commercial vehicles. It can be sanded with comparatively high grit abrasives (P120 P150) This putty is almost as hard as finish coating that provide a smooth transition between the repair and the undamaged surrounding area during sanding It can be applied directly prior to filler Due to its paste-like consistency, the putty is easy to apply in 2 4 mm coats Perfectly suitable for sanding by machine or wet sanding by hand Does not clog abrasives Easy to work also on surfaces with complicated shapes even when applying thicker layers Very good adhesion. Steel (incl. galvanized), aluminum, fiberglass plastic, OEM substrates*. Articles Pcs. / pack kg, w/hardener 10 Carbon Putty VOC < 250 g/l EU limit value: 2004/42/IIB(b)(250) to be treated must be cleaned, dried, degreased with CF Silicone Remover and sanded * Add 2 3% BPO Hardener by weight Pot life: 3 5 min min depending on ambient temperature Standard sanding method With P Further treatment With P (intermediate sanding step of 100 grit should be observed) Recommended sanding method First with P150, then with P240 Color black g/l Flash point 27 C Storage Keep away from direct sunlight Xn Harmful *Do not apply on one component (etch and anticorrosive) primers and thermoplastics. on paintworks is not recommended. 9

12 BLACK LABEL SERIES 2К Hi-Build Acryl Filler 5:1 Two component acrylic filler with excellent filling properties. 2K Hi-Build Acryl Filler 5:1 can be used instead of spray putty that provides shorter repair process and less material consumption. For treatment of large areas recoated with polyester materials. Excellent filling properties Due to its good flow, the product is easy to sand even when applied in 2 4 coats Does not drip even when applied with a spray gun with a 2.5 mm nozzle Sanding by hand or dry-sanding by machine All kinds of primed metal surfaces, fiberglass plastics, polyester putties, 2К acrylic fillers/primers, OEM and refinishing coatings. VOC: <540 g/l EU limit value: 2004/42/IIB(c)(540) Articles Pcs. / pack filler 3.5 L L filler L hardener hardener 0.7 L 12 to be treated must be cleaned, dried, degreased with CF Silicone Remover and sanded * 5:1 by volume with Hardener for 2КAcrylic Filler Hi-Build 5: mm / see spray gun manufacturer s instruction Viscosity: sec, FORD 4 (+20 С) 2 4 normal coats μm dry film thickness per one coat Pot life: ca. 45 min at 20 C Air drying (at +20 C ambient temperature) is not recommended Dry sanding: with P Further treatment - Flash-off: 10 min - Through-drying: 45 min at 60 C or Recoat with all conventional (solventborne) refinishing materials Xn - Flash-off: 10 min - Medium wave or short wave infrared drying: min Color grey 1530 g/l Flash point 23 C Harmful 10

13 BLACK LABEL SERIES А high-gloss two-pack clearcoat for fast repair of vehicle refinishing with conventional and waterborne basecoats. For two-coat paintworks in car and commercial vehicle refinishing. Extremely fast drying Due to slow speed of filming at the first moment after application, the clearcoat absorbs the paint overspray nicely. Very high-gloss Very good flow UV-resistant (does not yellow) and scratch-resistant Solid film with good chemical and mechanical resistance. Waterborne and solvent born basecoats, OEM coatings. Rapid Clearcoat 1:1 Articles Pcs. / pack Clearcoat, 500 ml Hardener, 500 ml 12 VOC 375 g/l EU limit value: 2004/42/IIB(d)(420) 2:1 with Hardener for 2K Ultra HS Clearcoat sec, FORD 4 (+20 С) Pot life: up to 30 min at 20 C 1.2 mm / see spray gun manufacturer s instructions 5 7 min flash-off between the coats 2 normal coats = μm dry film thickness Further treatment - Flash-off: 5 7 min min at 60 C or - Dust dry: min at 20 C - Set to touch: min at 20 C - Polishing: after min at 20 C - Full curing: after 5 hours Xn Flash point ca g/l >23 C 11

14 BLACK LABEL SERIES 2K Ultra HS Clearcoat 2К Ultra HS Clearcoat is a two-component high-gloss clearcoat for car refinishing with conventional and waterborne paint materials. For two-coat paintworks in car and commercial vehicle refinishing. Scratch resistance Very good flow UV resistance Optimized for application in spray booths and preparation zones. Waterborne and solventborne basecoats, OEM coatings. Articles Pcs. / pack L clear coat L hardener 12 2:1 with Hardener for 2K Ultra HS Clearcoat 1.2 mm / see spray gun manufacturer s instructions sec, FORD 4 (+20 С) 2 full coats = μm dry film thickness Pot life: up to 2 h at 20 C Further treatment - Flash-off: 7 10 min - 30 min at 60 C - Drying: 6 7 h at 20 C - Polishing: after h at 20 C - Full curing: 5 7 days or Short wave/medium wave infrared drying: 10 min Xn ca g/l Flash point 23 C Harmful 12

15 BLACK LABEL SERIES Strawberry scented cleaning agent based on volatile organic solvents for initial cleaning of old/ OEM coatings, primed and filled surfaces as well as plastics from resins, silicone, oil, grease, sanding dust and other contaminants. Non-toxic and ozone-friendly product. Surface cleaning prior to application of preparatory and refinishing materials and after sanding in car and commercial vehicle refinish. Metal and plastic parts, polyester putties, primers, fillers, fully cured old or fresh coatings. Silicone Remover Strawberry 765 g/l Flash point < 21 C VOC: 765 g/l EU limit value: 2004/42/IIB(a)(850) Articles Pcs. / pack L L 4 Do not use the product on solvent-sensitive substrates, e. g. thermoplastic coatings RFU Do not allow to dry on the substrate being treated Remove any remaining residue with a cleaning cloth Clean the substrate with CF Silicone Remover Strawberry Apply with a spray gun, a cloth or a sponge Xn F N Harmful Highly flammable Dangerous for the environment Pigment paste for 1К and 2К acrylic fillers based on organic solvents. Addition of the paste has no impact on hardener application process. Pigment Paste black Depending on the added amount of paste (1-5% by weight hardener), coatings with different shades of grey can be obtained. Color black g/l Flash point 27 C Articles Pcs. / pack ml 30 See TDS of the respective material Add 1 5% hardener by weight 13

16 BLACK LABEL SERIES Accelerator Special additive for accelerating the drying of two-component (2К) fillers and clearcoats. In case of clearcoats, the accelerator is to be used with standard and slow hardeners. The product saves approx. 15% of drying time. Waterborne and solvent born basecoats, OEM coatings. Articles Pcs. / pack L 12 * Prepare the surface according to main material application instructions While applying a filler, use the following mixing ratio: - filler 100%vol. - hardener 25%vol. - accelerator max. 18%vol. While applying a clearcoat, use the following mixing ratio: - clearcoat 100%vol. - hardener 50%vol. - accelerator max. 8%vol. Do not use fast and extra fast hardeners while mixing accelerator with clear coats as it will lead to opacity and coat adhesion decrease. Apply according to main material application instructions. Further treatment See main material application instructions. 900 g/l Flash point 24 C Toxic 14

17 PUTTIES Two component multifunctional fine-grained polyester putty for filling unevenness especially on aluminum and galvanized surfaces. Multifunctional finishing putty for eliminating car and commercial vehicle body imperfections. It is characterized by easily work in thick and thin layers It can also be used as finishing putty After drying it produces a smooth, pin-hole free surface Does not clog the sandpaper Intended for manual/machine dry sanding. Steel, galvanized surfaces, aluminum, fiberglass plastics, polyester materials, OEM substrates*. CF Multi Putty Articles Pcs. / pack kg, w/hardener 10 VOC < 250 g/l EU limit value: 2004/42/IIB(b)(250) to be treated must be cleaned, dried, degreased with CF Silicone Remover and sanded * Add 2 3% BPO Hardener by weight Pot life: 3 5 min min depending on ambient temperature Further treatment With P With P (intermediate sanding step of 100 grit should be observed) Color yellow 1760 g/l Flash point 31 C Storage Keep away from direct sunlight Harmful *Do not apply on one component (etch and anticorrosive) primers and thermoplastics. on paintworks is not recommended. 15

18 PUTTIES Soft Putty Two component polyester putty Soft is extremely easy to apply and adopts any desired shape regardless of the material coat thickness. Perfect solution for eliminating car and commercial vehicle body imperfections. For eliminating car and commercial vehicle body imperfections. Suitable for dry sanding by machine or by hand Optimal viscosity/plasticity ratio ensures uniform material application Fast drying prevents clogging of the sandpaper. All kinds of steel, fibers plastics, OEM substrates*. VOC: < 250 g/l EU limit value: 2004/42/IIB(b)(250) Articles Pcs. / pack kg, w/hardener kg, w/hardener kg, w/hardener 10 to be treated must be cleaned, dried, degreased with CF Silicone Remover and sanded * Add 2 3% BPO Hardener by weight Pot life: 3 5 min min depending on ambient temperature Further treatment With P With P (intermediate sanding step of 100 grit should be observed) Color yellow 1900 g/l Flash point 31 C Storage Keep away from direct sunlight Xn Harmful 16

19 PUTTIES Two component fiberglass-filled putty. Once dry fiberglass makes the putty highly durable. The product has an excellent adhesion to sanded metal. The putty is used in car and commercial vehicle repair for filling cracks, small holes and areas damaged by corrosion. Fiberglass putty for eliminating car and commercial vehicle body imperfections. High stability Limited sanding. All kinds of steel, aluminium, fiberglass plastics. Glass Putty Articles Pcs. / pack kg, w/hardener kg, w/hardener kg, w/hardener 10 VOC: < 250 g/l EU limit value: 2004/42/IIB(b)(250) to be treated must be cleaned, dried, degreased with CF Silicone Remover and sanded * Add 2 3% BPO Hardener by weight Pot life: 3 5 min min depending on ambient temperature Further treatment With P With P (intermediate sanding step of 100 grit should be observed) Color green 1800 g/l Flash point 31 C Storage Keep away from direct sunlight Xn Harmful 17

20 PUTTIES Plastic Putty Two component high-plasticity polyester putty for plastic parts repair. Excellent adhesion to plastics, fast drying and easy sanding. For repairs on plastic parts of cars and commercial vehicles. All kinds of plastic: ABS (acrylonitrile-butadiene-styrene copolymer) EP (epoxides/laminates) PA (polyamide) PBTP (polybutylene terephtalate) PC (polycarbonate) POM (polyoxymethylene) PP/EPDM (polypropylene-ethylene-propylene-diene monomer copolymer) PPO (polypropylene oxide) PUR (polyurethane) soft and hard PVC (polyvinyl chloride). VOC: < 250 g/l EU limit value: 2004/42/IIB(b)(250) Articles Pcs. / pack kg, w/hardener 24 to be treated must be cleaned, dried, degreased (e. g. with CF Silicone Remover) and treated with suitable matting materials * Add 2 3% BPO Hardener by weight Pot life: 4 5 min min depending on ambient temperature Further treatment With P With P (intermediate sanding step of 100 grit should be observed) Substrate to be treated must be thoroughly cleaned, degreased and dried Prior to putty application, the substrate must be sanded/treated with matting abrasives. Remove all old materials that have poor adhesion or have not fully dried. Do not apply this product on thermoplastic coatings or etch/acid primers Prior to application, mix well with a hardener/catalyst Apply at a temperature no lower than +10 C. Color grey 1858 g/l Flash point 31 C Storage Xn Keep away from direct sunlight Harmful 18

21 PUTTIES Two component polyester putty for filling surface irregularities, sanding marks and pinholes on car and commercial vehicle body parts as well as on vehicle structural components. Good adhesion to metals, wood, polyester materials and fiberglass plastics. Spray Putty is suitable for leveling small and big surface irregularities. The material dries quickly and creates a smooth pinhole-free surface. In order to achieve a high-quality finish coating, Spray Putty can be covered with a thin (~ 35 μm) sealing coat of 2К acrylic or 2К epoxy fillers without subsequent sanding. For leveling small and big surface irregularities of car and commercial vehicle bodies. Metal surfaces, polyester putties, fiberglass, wood. Spray Putty Articles Pcs. / pack kg, w/hardener 6 VOC: < 250 g/l EU limit value: 2004/42/IIB(b)(250) to be treated must be cleaned, dried, degreased with CF Silicone Remover and sanded Do not apply on etch primers, epoxy primers and fillers If necessary, use only waterborne epoxy primers * Add 3.5% CHP Hardener for Spray Putty Mix well prior to application min at C Viscosity as supplied = application viscosity (RFU) mm / see spray gun manufacturer s instructions Further treatment 3 5 h at C or With P min at 60 C or 15 min at 80 C Color grey 1650 g/l Flash point 31 C In order to isolate the substrate and prevent the formation of air bubbles (esp. in high humidity), apply 2К acrylic fillers 4:1, 5:1 Storage Xn Keep away from direct sunlight Harmful 19

22 CLEARCOATS 2K HS Clearcoat 2:1 SCRATCH RESISTANT Two component High Solid gloss clearcoat for partial or complete automotive two-coat paintworks. For two-coat paintworks in car and commercial vehicle refinishing. Suitable for applications in spray booths and preparation areas. High scratch resistance Suitable for application on solvent- and waterborne base coats Good flow High mechanical durability UV-resistance / non-yellowing Good chemical, mechanical and weathering resistance Waterborne and solvent-borne basecoats, OEM coatings. VOC: 535 g/l EU limit value: 2004/42/IIB(e)(840) Articles Pcs. / pack L clearcoat L hardener Clearcoat, 5 L Hardener, 2.5 L 4 2:1 with hardener for 2K HS Clearcoat 2: sec, FORD 4 (+20 С) Pot life: up to 2 hours at 20 C 1.2 mm / see spray gun manufacturer s instructions 2 normal coats = μm dry film thickness 10 min flash-off between the coats - Flash-off: 5 7 min - 30 min at 60 C or Further treatment - Dry through: 6 7 hours at 20 C - Polishing: after hours at 20 C - Full curing: 5 7 days Short and Medium wave: 10 min ca 1000 g/l (clearcoat) Flash point 23 C Xn Harmful 20

23 CLEARCOATS Two-component Medium Solid gloss acrylic clearcoat for two-coat finishes in partial and complete vehicle refinish. For two-coat industrial paintworks. Special finish for industrial use Suitable for application on solvent- and waterborne base coats Good flow High mechanical durability UV-resistance / non-yellowing Good chemical, mechanical and weathering resistance Waterborne and solvent-borne basecoats, OEM coatings. 2K MS Clearcoat 2:1 INDUSTRIAL USE Articles Pcs. / pack L clearcoat L hardener Clearcoat, 5 L Hardener, 2.5 L 4 VOC: 562 g/l EU limit value: 2004/42/IIB(e)(840) 2:1 with hardener for 2K MS Clearcoat 2: sec, FORD 4 (+20 С) Pot life: up to 1.5 hours at 20 C mm / see spray gun manufacturer s instructions 10 min flash-off between the coats 2 normal coats = μm dry film thickness - Flash-off: 5 10 min - 30 min at 60 C or Further treatment - Dry through: 5 7 hours at 20 C - Polishing: after 9 10 hours at 20 C - Full curing: 5 7 days Xn Short and Medium wave: 10 min 960 g/l (clearcoat) Flash point 23 C Harmful *Do not apply on one component (etch and anticorrosive) primers and thermoplastics. on paintworks is not recommended. 21

24 CLEARCOATS 2K UHS Clearсoat VOC 420 g/l EU limit value: 2004/42/IIB(d)(420) Two component Ultra High Solid gloss clearcoat for partial or complete automotive two-coat paintworks. For two-coat paintworks in car and commercial vehicle refinishing. Easy application Excellent flow Deep gloss High mechanical durability Yellowing resistance Can be polished in 60 minutes after cooling. Waterborne and solvent-borne basecoats, OEM coatings. Articles Pcs. / pack Clearcoat, 1 L Clearcoat, 5 L Standard hardener, 500 ml Standard hardener, 2.5 L Fast hardener, 500 ml Fast hardener, 2.5 L 4 2:1 with Hardener for 2K UHS Clearcoat + 0-5% CF Universal thinner sec, FORD 4 (+20 С) Pot life: min at 20 C Ready for use products are applied at a temperature higher than 15 C Too thick layers can have negative influence to drying time and level of gloss mm / see spray gun manufacturer s instructions 10 min flash-off between the coats Further treatment normal coats = μm dry film thickness - Flash-off: 10 min with fast hardener: 25 min at 60 C with standard hardener: 30 min at 60 C can be polished: 60 min after cooling or Xn - Full curing: hours at 20 C ca 1080 g/l (clearcoat) Flash point 24 C Harmful 22

25 CLEARCOATS One component gloss clearcoat for spot repair of automotive two-coat paintworks. For two-coat paintworks in car refinishing. Easy application Fast drying Very high gloss finish Excellent UV resistance Blends easily with existing 2K clear coating High performance clog-free aerosol can. Waterborne and solvent-borne basecoats, OEM coatings. 1K Acryl Clearcoat Spray Articles Pcs. / pack ml 6 VOC 710 g/l EU limit value: 2004/42/IIB(e)(840) Thoroughly clean and degrease surfaces with CF Silicone Remover. Sand old finish coating wet or dry with P800-P1000 abrasive. Clean and degrease surfaces with CF Silicone Remover once more. Apply basecoats according to the technical data sheet. Apply the clearcoat within 20 min after application of the base coat Shake can thoroughly before use at least for 2 minutes. Apply 1-2 normal, even coats Allow 5-10 minutes flash-off time between coats Further treatment Allow 30 minutes before handling Drying time depends on film thickness, air humidity and temperature. Xi ca 900 Flash point -40 C F Irrirating Extremely flammable This is a pressurized container, do not expose to direct sunlight or store above 50 C. 23

26 PRIMERS, FILLERS 1K Plastic Primer One component transparent primer for almost all kinds of plastic, designed to improve the adhesion of refinishing materials to the substrate. For priming plastic parts prior to application of subsequent materials in car and commercial vehicle refinishing. Contains a metallic pigment for controlling the process of application. ABS (acrylonitrile-butadiene-styrene copolymer), EP (epoxides/laminates), PA (polyamide), PBTP (polybutylene terephtalate), PC (polycarbonate), POM (polyoxymethylene), PP/EPDM (polypropylene-ethylene-propylene-diene monomer copolymer), PPO (polypropylene oxide), PUR (polyurethane) soft and hard, PVC (polyvinyl chloride), OEM coatings. VOC: 790 g/l EU limit value: 2004/42/IIB(e)(840) Articles Pcs. / pack L 12 to be treated must be cleaned, dried, degreased (e. g. with CF Silicone Remover) and treated with suitable matting materials sec at 20 C, RFU mm / see spray gun manufacturer s instructions 1 coat = 3 5 μm Ambient conditions: - temperature: no lower than +10 С - relative humidity: no more than 75% Further treatment 10 min at 20 C Color colorless, with metallic 894 g/l Flash point 10 C Recoat with 2К Plastic Filler and top coat Storage Keep away from direct sunlight Xn Harmful F Highly flammable 24

27 PRIMERS, FILLERS 1K ready for use adhesion promoter in an aerosol can. The plastic primer improves the adhesion of paint, adhesives or sealants to the most of car plastics. For two-coat paintworks in car refinishing. Easy application Fast drying May be overpainted with the most of paint systems High performance clog-free aerosol can. Most of plastics, polyester bodyfiller, sand G.R.P, old/original paintworks Plastic Primer Spray Articles Pcs. / pack ml 6 VOC 765 g/l EU limit value: 2004/42/IIB(e)(840) Thoroughly clean and degrease surfaces with CF Silicone Remover. * Shake can thoroughly before use at least for 2 minutes. Apply 2 thin even coats from a distance of cm. Before overcoats allow: - 30 min at 20 C or - 15 min at 60 C. Further treatment Drying time depends on film thickness, air humidity and temperature. Xi Overpaints with proper primer/filler or/and topcoat after drying. Color colorless 900 g/l Flash point -40 C F Storage Irrirating Extremely flammable This is a pressurized container, do not expose to direct sunlight or store above 50 C. 25

28 PRIMERS, FILLERS Hi-Build Filler Spray 1K ready for use high build filler in an aerosol can. Used for priming uneven surfaces before top coating. Filler is capable of producing a coating film thickness similar to that of a spray gun applied primer. For two-coat paintworks in car refinishing. Easy application Fast drying May be overpainted with the most of paint systems High performance clog-free aerosol can. Most plastics, polyester bodyfiller, sand G.R.P, old/original paintworks VOC 690 g/l EU limit value: 2004/42/IIB(e)(840) Articles Pcs. / pack ml 6 Thoroughly clean and degrease surfaces with CF Silicone Remover. * Shake can thoroughly before use for a minimum of 2 minutes. Apply 2 thin even coats from a distance of cm. Before overcoats allow: - 30 min at 20 C or - 15 min at 60 C. Further treatment Drying time depends on film thickness, air humidity and temperature. Overpaints with proper primer/filler or/and topcoat after drying. Xi Flash point 900 g/l -40 C F Storage Irrirating Extremely flammable This is a pressurized container, do not expose to direct sunlight or store above 50 C. 26

29 PRIMERS, FILLERS Two component acrylic high-solid filler for vehicle refinishing with conventional (solventborne) materials. The product is applied on clean steel, aluminium and galvanized substrates (after pretreatment with an etch primer), OEM / cataphoresis primers and polyester putties. For sealing body parts of cars and commercial vehicles. Very good filling properties Fast drying Wet and dry sanding All kinds of primed metal surfaces, fiberglass plastics, polyester putties, 2К acrylic fillers/primers, OEM and refinishing coatings. 2К HS Acryl Filler 4:1 grey Articles Pcs. / pack L filler L hardener filler 3.6 L hardener for filler 900 ml 12 VOC: 490 g/l EU limit value: 2004/42/IIB(c)(540) to be treated must be cleaned, dried, degreased with CF Silicone Remover and sanded 4:1 by volume with Hardener for 2К HS Acrylic Filler 4:1 Pot life: up to 60 min at 20 C sec, FORD 4 (at +20 С) mm / see spray gun manufacturer s instructions 5 15% CF Universal Thinner - Dust-free: 30 min - Through-drying: 3 5 h at 20 C or 1 3 normal coats = μm With P Further treatment - Flash-off: 10 min at 20 C - Through-drying: min at 60 C or Recoat with all conventional (solventborne) refinishing materials Xn - Flash-off: 10 min at 20 C - Medium wave or short wave infrared drying: min Color grey 1550 g/l Flash point > 23 C Harmful 27

30 PRIMERS, FILLERS 2K Acryl Filler Wet-on-Wet Acrylic filler 6:1 is used in the repair of damaged and new body parts. The product is applied wet on wet or as a sandable filler. Once the filler has dried completely, it can be wet or dry sanded manually or by machine. This method is suitable for application of polyester putties to repair small or medium damages. When applied wet on wet, the filler efficiently seals the surface to be painted without intermediate drying and sanding. For the repair of damaged and new body parts by application wet on wet or with sanding. Very good sealing properties Suitable for all kinds of organic solvent-based paintworks Very good filling properties Very fast drying. All kinds of primed metal surfaces, fiberglass plastics, polyester putties, 2К acrylic fillers/primers, OEM and refinishing coatings. VOC: 540 g/l EU limit value: 2004/42/IIB(c)(540) Articles Pcs. / pack L filler L hardener 12 to be treated must be cleaned, dried, degreased with CF Silicone Remover and sanded 6:1 by volume with Hardener for 2K Acryl Filler Wet-on-Wet Pot life: ca. 60 min at 20 C 5 15% CF Universal Thinner 1 full coat = μm mm / see spray gun manufacturer s instructions Further wet-on-wet treatment Recoat with all conventional (solventborne) refinishing materials - Flash-off: 5 7 min - Recoatable: after min at 20 C Further treatment with intermediate sanding 2 3 full coats = μm With P Flash-off between coats: 5 7 min - Sanding: after 3 4 h at 20 C or Recoat with all conventional (solventborne) refinishing materials Xn - Flash-off: 10 min at 20 C - Through-drying: 20 min at 60 C Color grey 1390 g/l Flash point > 23 C Harmful 28

31 THINNERS, CLEANERS Cleaning compound based on volatile organic solvents for initial cleaning of old/oem coatings, primed and filled surfaces as well as plastics from resins, silicone, oil, grease, sanding dust and other contaminants. Non-toxic and ozone-friendly product. Surface cleaning prior to application of preparatory and refinishing materials and after sanding in car and commercial vehicle refinish. Metal and plastic parts, polyester putties, primers, fillers, fully cured old or fresh coatings. Silicone Remover 765 g/l Flash point < 21 C Articles Pcs. / pack L L 4 VOC: 765 g/l EU limit value: 2004/42/IIB(a)(850) Do not use the product on solvent-sensitive substrates, e. g. thermoplastic coatings RFU Clean the substrate with CF Silicone Remover Apply with a spray gun, a cloth or a sponge Xn Do not allow to dry on the substrate being treated Remove any remaining residue with a cleaning cloth Harmful N Dangerous for the environment F Highly flammable Universal Thinner Product for thinning all kinds of C.A.R.FIT refinishing materials. Thinning of primers, fillers and clear coats in car and commercial vehicle refinishing. Metal and plastic parts, polyester putties, primers, fillers, fully cured old or fresh coatings. 900 g/l Flash point 24 C Articles Pcs. / pack L L 4 to be treated must be cleaned, dried, degreased with CF Silicone Remover and sanded See TDS of the principal material Xn Harmful 29

32 THINNERS, CLEANERS Fade Out Spray Fade Out Spray is a special thinner for fast, simple, accurate dissolving of edges of 2K Clearcoat repairs. It increases efficiency of the fade out process to give an invisible blend. Using this product in partial coating repair provides a result of a smooth fade out between old and new coatings. For paintwork repair in car refinishing. Easy application Fast drying Ideal for use with both MS and HS Clearcoat UV stable High performance clog-free aerosol can. Refinish clearcoats, old/original and OEM paintworks. VOC 688 g/l EU limit value: 2004/42/IIB(e)(840) Articles Pcs. / pack ml 6 Apply base coat and then clearcoat according to TDS. * Shake can thoroughly before use for a minimum of 2 minutes. Once the clearcoat has been applied a light mist coat Fade Out Spray is applied over the blend area holding the aerosol 25cm from the panel. The blending process is best undertaken in two rapid light passes of the aerosol. The blend edge will melt into the original paintwork requiring little or no processing once the clear coat has cured. Fade Out Spray is used when blends or spot repairs operations are being carried out; all these processes result in an interface being created between the existing, cured coating and the freshly applied clear coat. If the interface is not treated a dry edge will be visible upon cure of the fresh coating. Further treatment Xn Once applied the clearcoat manufacturer s instructions for flash off and air/force dry should be followed. Color Flash point colorless ca 800 g/l -40 C F Storage Harmful Extremely flammable This is a pressurized container, do not expose to direct sunlight or store above 50 C. 30 *Do not apply on one component (etch and anticorrosive) primers and thermoplastics. on paintworks is not recommended.

33 BODYCOATS, CABIN COATS Synthetic resin-based stone chip protection of vehicle underbody and lower body. The coating can be primed or overpainted in any color within minutes after drying. The coating has high durability and excellent resistance to abrasive wear. It also has sound deadening and vibration absorbing properties. For treatment of car and commercial vehicle bodies. Supplied in a bottle always ready for use Recoatable Produces a durable coating that is resistant to abrasive wear and aggressive chemicals Sound deadening and vibration absorbing properties. Various metal surfaces, primed metal parts, old/oem coatings. Stone Chip Protection Articles Pcs. / pack L bottle, black L bottle, grey 12 VOC: g/l EU limit value: 2004/42/IIB(e)(840) Clean the substrate with CF Silicone Remover Shake well before use for about 3 min Do not apply on engine, brake system and exhaust pipe Apply several coats with a sprayer at a spray pressure of 4 5 bar Xn tack-free: 1.5 h recoating: after 1 h Color black / grey 1400 g/l Flash point < 21 C Harmful F Highly flammable 31

34 BODYCOATS, CABIN COATS Tack Coating for Spray Booth Booth mask safely binds paint, dust and overspray particles that tend to settle on spray booth walls and ceiling panels, thus preventing contamination of the surface being refinished. The compound stays transparent and water-soluble. Thin and sticky protective film never dries out on the wall, ensuring safe dust and overspray binding. Once the film loses its particle-binding capacity, it can be easily washed off with water and a sponge and then reapplied. For overspray and dust protection of spray booth walls. Provides dust protection of the object being refinished Protects spray booth surfaces from paint, dust and overspray Specially designed to protect glass and lights without impacting light permeability and reflection capacity. Easy to apply and remove Very cost-effective. Depending on the level of contamination, the coating should be replenished once in a few weeks. 100% environmentally-friendly. Aluminium, steel and galvanized walls of spray booth cabins; fully cured and clean paintworks. TACKY COAT Articles Pcs. / pack L 1 Do not apply on walls that have already been exposed to overspray and other materials Viscosity as supplied = application viscosity (RFU) Apply a uniform thin coat with a brush or mm / see spray gun manufacturer s instructions Apply a uniform thin coat with a roller or 1 2 coats = μm or Refer for consultation of airless spray equipment manufacturer Further treatment Depends on the coat thickness of the material being applied. For best results, we recommend to apply the material in 1-2 coats with a 20 min flash-off between the coats. Two coats ensure durable protection with no risk of the coating being washed away. All tools used for the application of the coating must be thoroughly washed with water. If the temperature inside the spray booth is C, the coating should be renewed more often: at least once a month. This will prevent the protective film from drying up. If necessary, several new layers can be applied on the old film. In case of a long operation life of the spray booth, it is recommended that the old protective film should be removed prior to application of a new one. Removal Remove with a sponge and water Color transparent 1024 g/l Coverage 8-10 m 2 /l Store in a cool dry place protected from freezing Storage Contains no harmful or life-threatening components. Can be disposed of as harmless waste in accordance with the local legislation. 32

35 SEALANTS PU Adhesive and Sealant is a one-component polyurethane sealant. By reaction with air humidity, the product cures into a strong but flexible rubber, with excellent adhesion to many substrates. It will not sag even when applied in thick layers. The product is resistant to ageing, weather and is impermeable to water. PU Adhesive and Sealant is suitable for sealing all kinds of joints: overlaps, flanges, linearweldings, spotweldings etc. It is also used to seal drains, lamp housings, reversible roofs and other car body parts. Excellent adhesion to most rough and treated metal sheet Once fully cured* the sealer can be recoated with any two component paint materials. *preliminary tests are recommended prior to application of resin-based paints. Various metal surfaces, e. g. aluminium, wood, primed substrates, thermoreactive plastic, old/ OEM coatings. Articles Pcs. / pack ml tube, grey ml tube, black 12 PU Adhesive and Sealant VOC (grey and black): 7% EU limit value: 2004/42/IIB(e)(840) Clean and degrease surfaces with solvent like acetone. Oxidized metal surfaces and concrete must be first sanded and then cleaned. Degrease PVC, aluminum and glass with a non greasy solvent, like acetone. The temperature of the substrate must be within C In case of application by cold weather, store the cartridges at 20 C before use Prior to application, carry out a test on adhesion efficiency and compatibility with each of the materials upon which the sealant will be applied Puncture the cartridge and section the nozzle according to the extrusion diameter required, remove the metal base and the dehydrating salts and extrude from cartridge with a manual or pneumatic gun. Film thickness depends on the characteristics of the materials being bonded. The joint should be overlapped on the previous section; the end-to-end joint is prohibited to avoid the leakage of water. The process of bonding must take no more than 10 minutes. PU sealant has a relatively high viscosity. Therefore, it is advisable to use special clamps for locking the parts being bonded until the sealant dries completely. Tack free time: 60 min at 23 C and 50% r.h. Cure rate: 4 mm / 24 hrs at 23 C and 50% r.h. Color black grey 1150±50 g/l 1180±50 g/l Flash point C C Hardness Shore A (ISO s) approx. 45 approx. 45 Elongation at break (ISO 37) > 600% > 600% Tensile at 100% elongation (ISO 37) 0.6 MPa 0.6 MPa Temperature resistance C C Storage Store in cool dry place and at temperature < 25 C, avoid sunlight Xn Harmful 33

36 SEALANTS Windglass Glue Windglass Glue is a one component, high viscosity, moisture curing polyurethane adhesive, primarily used for automotive direct glazing with and without airbag. It cures in a longer time allowing application on big windscreens such as buses and trucks. Windscreen direct glazing. Does not drip when used on vertical surfaces Flexibility, excellence curing Prevents metal corrosion and penetration of contaminants into the vehicle Prevents yellowing The cured product forms a durable glue film. Various metal surfaces, incl. glass, aluminum, ceramic coatings, old/oem coatings. VOC (grey and black): 3% EU limit value: 2004/42/IIB(e)(840) Articles Pcs. / pack ml tube, black 12 Clean and degrease surfaces with solvent like acetone. Let dry after degreasing. The substrates to be bonded must be dry, oil-free, grease-free, dust-free and free of any contaminating agents that could harm bonding. In cold weather, store the cartridges or sausages at a temperature of about 20 C before use. Do not wipe the substrate up and down. If the pad has got dirty, replace it with a new one and continue the procedure. If the primer peels off, replace the windshield to avoid unpredictable consequences. If any deviations in the substrate material are detected, it is advisable to carry out an adhesion test prior to actual bonding. Test bonding of the windshield with any materials is particularly recommended to achieve desirable adhesion. Avoid any contact with non-cured MS, hybrid PU or silicone sealants as well as with alcohols or ammonia during curing. Apply the glass coated with the sealant on the car body and press, before the skin formation time (i.e. within 30 minutes). Apply the glue with a glue gun onto the substrate. Install the glass onto the window frame and use the palm to press softly till the glass is bound flatly. Adjust the space up and down, left and right, and use the press sensitive tape to fix. Do not apply at a temperature below +5 C. Excessive glue can be removed with a scraper or soapy water. If any glue residue remains on the substrate, quickly remove it with an alcohol-free cleaning agent, e. g. gasoline. If the glue has hardened, use a blade. Color Flash point Hardness Shore A (ISO s) Tack free time: min at 23 C and 50% r.h. Cure rate: > 3.5 mm / 24 hrs at 23 C and 50% r.h Drive-away time at 23 C and 50% r.h.: - 6 hrs. no airbag - 8 hrs. with airbag black Shear strength (Ford SAE J 1529) 95% 1190 g/l Elongation at break (ISO 37) mm /24 h Tensile strength (ISO 37) 2.0 МPa g/min Storage Store in cool dry place and at temperature < 25 C, avoid sunlight Xn Harmful 34

37 ANCILLARY MATERIALS Rubbing Compound Polishing paste without silicone for removing sanding marks left on fresh and old coatings by manual or machine sanding with P grit abrasives. Polishing of car and truck coatings. Old/OEM or fully cured fresh refinishing coatings. Articles Pcs. / pack ml 6 The substrate must be thoroughly cleaned of dust using a sponge with water and degreased with degreasing compounds. 1. Fresh and fully cured paintworks Use a woolen polishing pad. Switch on the sander to a continuously low speed and move across the surface to achieve the desirable result. After manual sanding with abrasive paper, especially on dark surfaces, repeated polishing may be necessary. Once almost all the paste has been used up, increase the RPM of the sander for better cleaning of the surface. For higher shine and deeper color, repeat the operation with a yellow foam polishing pad until complete removal of fine scratches left by the woolen polishing pad. 2. Old paintworks Use a foam polishing pad. Switch on the sander to a continuously low speed and move across the surface to achieve the desirable result. Once almost all the paste has been used up, increase the RPM of the sander for better cleaning of the surface. Apply the product onto the surface, not the polishing pad! Mask plastic parts in advance to avoid their contamination Avoid overheating of the surface A few minutes after polishing, remove the compound residue with a microfiber cloth. Abrasive aluminium oxide Consumption ml/m 2 Storage 35

38 MASKING Masking Film electrostatic effect Semi-transparent polyethylene masking film has good adhesion to refinishing coatings due to its electrostatic charge and is highly resistant to weathering. For quick masking of large vehicle surfaces and parts prior to painting. Metal and plastic parts, rubber, glass, chrome-plated surfaces, OEM/refinishing coatings. Technical Data Size 3.8 m x 200 m 55 cm x 33 m 4 m x 5 m Thickness 9 μm 9 μm 7 μm Material HDPE (High Polyethylene) Heat resistance С Static treatment + Corona treatment 44 dyne/cm Articles Pcs. / pack m х 200 m, roll m х 5 m, folded m х 7 m, roll 1 Masking Tape Slightly creped masking tape with excellent elongation characteristics and high initial adhesion strength. The product is suitable for masking jobs for sanding as well as for application of waterborne or solventborne refinishing materials with subsequent drying in a spray booth. Once the refinishing coating has dried, the masking tape comes off cleanly and leaves no residue. Professional masking tape for secure vehicle body protection from overspray during refinishing with subsequent drying in a spray booth at a temperature of 60 С. Metal parts, rubber, glass, chrome-plated surfaces, OEM/refinishing coatings. Technical Data Backing material impregnated crepe paper Thickness 90 ± 15 μm Tensile strength 50 ± 15 N/mm 2 Elongation at break 9 ± 2 % Adhesive material Adhesion Tack (Rolling Ball Tack) Articles Pcs. / pack width 19 mm, 80 С width 25 mm, 80 С width 38 mm, 80 С width 50 mm, 80 С 18 natural rubber 4.5 ± 1 N/25 mm < 3 cm 36

39 MASKING Pretaped Masking Films Polyethylene masking film with an adhesive tape for refinishing works. It prevents overspray from getting onto the surface being treated. The masking film is highly-durable and adheres well to the surface. Articles Pcs. / pack mm х 33 m, roll mm х 20 m, roll 1 Classic foam tape for masking gaps and apertures in the vicinity of doors, bonnet, trunk and gas cap lid. The masking tape helps avoid sharp edges in painting and prevents overspray from getting inside the vehicle. The tape is dust and paint-proof that makes the use of passenger compartment protection unnecessary. Classic Foam Masking Tapes classic Articles Pcs. / pack mm х 50 m, roll mm х 35 m, roll 1 Transparent tape for vehicle steering wheel protection during repair. Supplied in roll, without dispenser. Protective Film for Steering Wheel Articles Pcs. / pack m, roll dispenser for steering wheel 1 protective film, length 125 mm 37

40 MASKING Disposable Floor Mats Disposable auto floor mat designed to protect the floor of the vehicle from dirt during repair and maintenance. Articles Pcs. / pack size: 38 cm x 50 cm 500 Polyethylene Car Cover Polyethylene cover specially designed to protect freshly painted and damaged cars as well as car assemblies, aggregates and parts during inspection/handover. Cover edge is outfitted with an elastic band for secure masking. Suitable for indoor and outdoor use. Reusable. Articles Pcs. / pack size L, 7.5 m x 4.8 m x 30 μm 20 Seat Covers Pre-cut polyethylene seat cover for masking vehicle seats during repair. Supplied in perforated rolls for easy tear-off. Articles Pcs. / pack size: 82 cm x 130 cm x 10 μm

41 MASKING Handy bags made of semi-transparent polyethylene for seasonal tire storage. The bags are fitted with a tag displaying the customer s name and wheel size for quick identification. Tire Bags Articles Pcs. / pack size: 70 cm x 30 cm x 100 cm

42 CLOTHS Car Clean Multi Lint-free cloths (w/o dispenser) with a high resistance to oils and solvents for the removal of spilled oil, paint, ink, etc. Special impregnation for higher absorption capacity High absorption capacity enables the cloth to absorb 8 times its own weight in liquid Suitable for cleaning and wiping of equipment, floors, workpieces, etc. Durable and soft at the same time Material density: 75 g/m 2 Articles Pcs. / pack mm х 320 mm, dispenser mm х 267 mm 50 Double Layer Cleaning Cloths Highly durable double-layer lint-free cleaning cloths made of quality embossed crepe paper. Supplied in perforated rolls. Material density: 2x2.22 g/m 2 Articles Pcs. / pack mm х 370 mm, rolls 1000 Microfibre Cleaning Cloth Woven microfiber cloth for fast and efficient cleaning of the surface without using cleaning agents. Captures and binds contaminants in a fast and efficient way Restores the gloss and color of the paintwork Does not require cleaning agents cost saving Reusable after washing Material density: 300 g/m 2 Articles Pcs. / pack mm х 400 mm, folded 1 40

43 CLOTHS Soft lint-free polishing cloth made of synthetic nonwoven fabric for the manual polishing of new and old coatings. Nonwoven Polishing Cloth Articles Pcs. / pack mm х 400 mm, roll 400 Cotton tack cloth for cleaning dust from all kinds of surfaces, including water-based coatings. Does not wrinkle no need in smoothing out the fabric. Wax and silicone-free. Tack Cloth Articles Pcs. / pack cm х 50 cm, folded 5 Tack Cloth Super Wave Tack cloth Super Wave easily adopts palm shape, due to which it fits tightly against the surface upon wiping no need in supplementary devices. Larger area of the surface and, at the same time, a smaller contact zone allow for secure dust binding inside the cloth, regardless of the size of dust particles. The carrier material lets dust easily enter into the inner layers and provides additional security and the highest possible dust absorption capacity. The impregnation of the cloth does not dry out and is compatible with all kinds of refinishing materials. For dust binding for dust-free sanding and refinishing. Wavelike surface is hugely important for removing dust from large and even parts Easily adapts to the surface being treated Excellently absorbs dust Glides easily along the surface User-friendly No need in supplementary devices. Metal parts, rubber, glass, chrome-plated surfaces, putties, primers/fillers, OEM/refinishing coatings. Articles Pcs. / pack cm х 90 cm 1 41

44 POLISHING MATERIALS Woolen Polishing Discs Velcro Woolen polishing discs with self attachment Velcro system. To be used with Universal Polishing Paste. Articles Pcs. / pack Diam. 150 mm Diam. 180 mm 1 Foam Polishing Discs Velcro Foam polishing discs with self attachment Velcro system. Articles Pcs. / pack Hard, diam. 150 mm Medium-Hard, diam. 150 mm Soft, diam. 150 mm 1 Pads for Polishing Discs Velcro Velcro foam polishing pad for finish polishing jobs. Articles Pcs. / pack For disc diam. 180 mm, M For disc diam. 150 mm, M

45 ACCESSORIES Synthetic nitrile rubber gloves with high resistance to organic solvents (benzene, benzines), formaldehyde, ketones, ethers, acids and oils. The gloves efficiently prevent non-organic and grease contaminants from getting onto the paintwork. The product complies with the standard EN Nitrile Gloves Articles Pcs. / pack size XL size L 100 The gloves can be used while working with chemicals, except solvents and formaldehyde. They also prevent non-organic solvents and grease from getting onto the paintwork. The gloves are NOT powdered, and therefore, can be used in paint manufacturing. The product complies with the standards EN 374-1/2/3. Latex Gloves Articles Pcs. / pack size XL size L 100 Vinyl Gloves Gloves designed to provide hand skin protection from technical contaminants (paints, solvents, etc.) and prevent non-organic substances and grease from getting onto the paintwork. The gloves are NOT powdered, and therefore, can be used in paint manufacturing. Articles Pcs. / pack size XL size L

46 ACCESSORIES Paint Coverall Light and comfortable paint overall made of processed cellulose impregnated with polyethylene which makes it more durable and prevents skin exposure to liquid and aerosol materials. The overall is outfitted with a zip fastener and elastic cuffs on sleeves, pant legs and hood for overspray protection. Articles Pcs. / pack size L size XL 1 Disposable Paint Strainers Paper filter with an insert made of artificial material for filtering paint and similar materials based on organic solvents. The strainer efficiently removes foreign particles that can get into refinishing materials and cause spray gun clogging. Articles Pcs. / pack μm μm 1000 Metal Test Card Metal test card for testing automobile paints prior to application. Suitable for application of solventborne, and waterborne paints. Articles Pcs. / pack х

47 ACCESSORIES High-quality solvent proof cups and lids for accurate mixing of refinishing materials: paints, clear coats, fillers, etc. A mixing ratio scale is printed on the side of the cup. Mixing Cups Articles Pcs. / pack cup l cup l cup 1.4 l cup 2.3 l lid for cup l lid for cup l lid for cup 1.4 l lid for cup 2.3 l 100 Paint Mixing Stick Solvent-proof plastic stick for paint mixing. Articles Pcs. / pack length 23 cm 100 The sprayer with an air pump is intended for spraying silicone removers and thinners/ cleaners. It is made of plastic that is resistant to said materials. Pump Spray Articles Pcs. / pack L 1 45

48 ACCESSORIES Sanding Block for 150-mm Abrasive Discs Manual sanding block for 150-mm abrasive discs. Articles Pcs. / pack Polyurethane, Velcro 1 Rubber Sanding Block Rubber block for sanding works. Articles Pcs. / pack Rubber, 67 х 125 mm 1 Manual Polishing & Sanding Pad Velcro back-up pad for polishing and sanding discs. Articles Pcs. / pack Polyurethane, for 150 mm discs 1 46

49 ACCESSORIES Sanding block with a flat working surface for manual sanding of small and inaccessible areas. Flat Sanding Block Articles Pcs. / pack x 198 mm 1 Sanding block with a semi-round working surface for manual sanding of small, complexshaped and inaccessible areas. Semi-Round Sanding Block Articles Pcs. / pack x 198 mm 1 The dispenser allows one person to perform complete vehicle masking. Masking Film Dispenser Articles Pcs. / pack Steel 1 47

50 ACCESSORIES Mobile Masking Paper Dispenser Dispenser accommodating 3 separate rolls of masking paper at a time, fitted with masking tape-removing rollers. Perfect solution for fast and cost-saving masking to provide overspray protection to vehicles. Articles Pcs. / pack Steel 1 Folding Paint Stand Premium Folding stand for securing the workpiece in a convenient position for the painter. The stand is very stable and accommodates bulky and heavy parts. Articles Pcs. / pack With 2 additional fasteners 1 Rotating Paint Stand Multipurpose rotating paint stand with spray gun holders and a set of fixtures for extensions. The paint stand provides aid in refinishing car doors, bonnets, trunk lids, etc. Articles Pcs. / pack With 6 extensions