SELECTION AND PREPARATION OF SUBSTRATES
|
|
- Horatio Wilcox
- 5 years ago
- Views:
Transcription
1 592 TECHNICAL DATASHEET / SELEMIX DIRECT GLOSS TOPCOATS PRODUCT DESCRIPTION Selemix Direct Gloss are polyurethane coatings based on PU 2K technology, which can be applied direct onto substrates giving gloss levels of approximately 80 to 85% at 60 Gloss. The product characteristics are: - One layer system. - High thickness: up to 160µm wet film. - Can be sprayed with airless, air-assisted airless, conventional, or HVLP methods - Good adhesion on various substrates such as bare steel, aluminium, galvanised steel, fibre reinforced plastic. - High coverage due to highly concentrated pigment pastes. Selemix Direct is <420g/L VOC when using the HS Hardener in airless and air assisted airless modes. PRODUCTS 2 Binders :. For white and pastel colours: For other colours: Direct Binder GL 80% Light colours Direct Binder GL 80% Note: Gloss levels quoted are within +/- 10% depending upon colour 3 Hardeners : Direct Hardener Acrylic Hardener HS Direct Hardener 2 Thinners : Direct Thinner Extra Slow Thinner SELECTION AND PREPARATION OF SUBSTRATES Substrate Cast Iron Bare steel Phosphated steel Galvanized steel Light alloys Aluminium Fiber reinforced plastic Sand P (dry) P80-120(dry) or shot blast Scotch brite Scotch brite P (dry) P (dry) P240 (dry) Degrease All surfaces should be thoroughly degreased using the appropriate cleaner 1
2 APPLICATION GUIDE USING or HARDENERS Tinting Ratio By weight : White and pastel colours Binder: 95 Tinters: 5 AIR ASSISTED Mixing ratio: Volume Weight Mixed col. 4 vol / vol XX** 1 vol 200 Other Colours Binder: 85 Tinters: 15 Volume Weight Mixed col. 4 vol / vol XX** vol Notes: hardener is recommended for air-drying overnight Thinner can be used for application temperatures below 25 C Extra Slow thinner is recommended for application temperatures above 25 C. Stir in Hardener after addition before adding thinner and then stir again. viscosity: sec sec Pot life at 20 C: gun set up: pressure: 2-3 hours 3 hours thou tips Nozzle =1.8 mm bar bar Standard 3-4 bar HVLP 2 bar Air cap pressure: bar Number of coats: Flash off between coats minutes minutes Total dry film build : Higher thickness can be achieved with additional coats This may extend the drying time 2
3 APPLICATION GUIDE USING or HARDENERS Drying times at 20 C : dust free : tack free : hard dry stoving : 1,5-2 hours 45 min at 60 C 2 hours 45mn at 60 C Recoatability: Colour: Selemix Direct Topcoats can be overcoated without sanding, with themselves 10 days after drying and up to 5 months after drying. It is extremely important that the surface is thoroughly cleaned before overcoating. Check colour and gloss before use APPLICATION GUIDE USING HARDENER AIR ASSISTED Mixing ratio: Volume Weight Mixed col. 6 vol vol XX** 0.7 vol. 100 Volume Weight Mixed col. 6 vol vol XX** 1.5 vol. 250 Notes: Thinner can be used for application temperatures below 25 C Extra Slow thinner is recommended for application temperatures above 25 C. Stir in Hardener after addition before adding thinner and then stir again. viscosity: sec sec Pot life at 20 C: gun set up: pressure: 2-3 hours * 2-3 hours * thou tips Nozzle = 1.8 mm bar bar Standard 3-4 bar HVLP 2 bar Air cap pressure: bar 3
4 APPLICATION GUIDE USING HARDENER Number of coats: Flash off between coats Total dry film build : minutes Higher thickness can be achieved with additional coats This may extend the drying time minutes Drying times at 20 C : dust free : tack free : hard dry stoving : 6 hours 45 mins at 60 C 6 hours 45 mins at 60 C Recoatability: Selemix Direct Topcoats can be overcoated without sanding, with themselves 10 days after drying and up to 5 months after drying. It is extremely important that the surface is thoroughly cleaned before overcoating. Colour: Check colour and gloss before use TECHNICAL DATA VOC : Solid content : Theoretical coverage in m²/ Lt of ready to spray product & AIR ASSISTED g/l ready for use 58-60% 5.6 m²/l dry film thickness:80µm g/l ready for use 56-58% 5.2 m²/l dry film thickness:80µm 4
5 VOC EU REGULATIONS The EU limit value for this product when used with or hardeners (product category: IIA(j)) ready to use form is max. 550 g/l of VOC (from 1/1/2007) and 500 gr/lt of VOC (from 1/1/2010). The VOC content of this product in ready to use form is max. 500 g/l except for conventional applications where VOC content is max 550 g/l. The EU limit value for this product when used with hardener (product category: IIA(j)) ready to use form is max. 550 g/l of VOC (from 1/1/2007) and 500 gr/lt of VOC (from 1/1/2010). The VOC content of this product in ready to use form is max. 500 g/l except for conventional applications where VOC content is max 550 g/l. HEALTH AND SAFETY For comprehensive Health, Safety and Environmental advice, please refer to the relevant Material Safety Data Sheets and Product can labels. This product is for professional use only. The information given in this sheet is for guidance only. Any person using the product without first making further enquiries as to the stability of the product for the intended purpose does so at his own risk and we can accept no liability for the performance of the product or for any loss or damage (other than death or personal injury resulting from our negligence) arising out of such use. The information contained in this sheet is liable to modification from time to time in the light of our experience and our policy of continuous product development. Drying times quoted are average times at 20 C. Film thickness, humidity and shop temperature can all affect drying times. Selemix System is a brand of PPG Group Selemix Customer Service and Sales Group, Needham Road, Stowmarket, Suffolk, IP14 2AD, England, Tel: , Fax:
January 2007 Product Information DELTRON D821
GLOBAL REFINISH SYSTEM January 2007 Product Information DELTRON High Solids Chip Resistant Primer PRODUCT DESCRIPTION is a transparent-grey primer surfacer with excellent anti-chip and anti-corrosion properties.
More informationProduct Information PRIMA D839 2 Component Primer
GLOBAL REFINISH SYSTEM March 2011 Product Information PRIMA 2 Component Primer PRODUCT DESCRIPTION Prima is a grey 2K primer surfacer, suitable for a wide range of day-to-day repair work. Versatile, quick
More informationHP Epoxy Primer P
Product Data Sheet September 2006 (updated November 2016) INTERNATIONAL MASTER FOR PROFESSIONAL USE ONLY HP Epoxy Primer P580-3005 Product Description P580-3005 HP Epoxy Primer P275-3022 Hardener for Epoxy
More informationHP Chromate Free Epoxy Primer P /-4505/-4510
Product Data Sheet September 2011 (February 2013 update) INTERNATIONAL MASTER FOR PROFESSIONAL USE ONLY HP Chromate Free Epoxy Primers P580-4501/-4505/-4510 Product Description P580-4501 HP Chromate Free
More informationProduct Data Sheet November 2016
Product Data Sheet November 2016 INTERNATIONAL MASTER FOR PROFESSIONAL USE ONLY T8500V HP Chromate Free Epoxy Primer P580-3501/-3502/-3503/-3504 Product Description P580-3501 HP Chromate Free Epoxy Primer
More informationProduct Data Sheet August 2006 (Updated in December 2014)
Product Data Sheet August 2006 (Updated in December 2014) INTERNATIONAL MASTER FOR PROFESSIONAL USE ONLY Fastbuild TM Product Description P540-400 Fastbuild - green P540-401 - off white P540-402 - grey
More informationProduct Information Deltron D894 High Solids Clear
GLOBAL REFINISH SYSTEM May 2012 Product Information Deltron High Solids Clear PRODUCTS Deltron HS Clear Deltron HS Hardeners D897, D8208 Deltron MS Hardener D803, D841, D861, D864 Deltron Thinners D808,
More informationJuly 2014 Product Information GRS DELTRON D8122 CERAMICLEAR TM 8122 CeramiClear 8122 Clear
GLOBAL REFINISH SYSTEM July 2014 Product Information GRS DELTRON CERAMICLEAR TM 8122 CeramiClear 8122 Clear PRODUCTS Deltron CeramiClear 8122 Clear Deltron HS Hardeners Deltron Thinners Deltron Catalyst
More informationUHS Duralit Extra Tinters series 150
2K ACRYLIC FINISH 2:1 UHS Duralit Extra, is a 2K Acrylic Topcoat enamel for direct gloss solid colours. It has been developed for use where product VOC is restricted. UHS Duralit Extra provides maximum
More informationJuly 2014 Product Information GRS DELTRON D8122 CERAMICLEAR TM 8122 CeramiClear 8122 Clear
GLOBAL REFINISH SYSTEM July 2014 Product Information GRS DELTRON CERAMICLEAR TM 8122 CeramiClear 8122 Clear PRODUCTS Deltron CeramiClear 8122 Clear Deltron HS Hardeners Deltron Thinners Deltron Catalyst
More informationMarch 2009 Product Information RAPID GREYMATIC 2K Filler
GLOBAL REFINISH SYSTEM March 2009 Product Information RAPID GREYMATIC 2K Filler PRODUCT DESCRIPTION 2K RAPID GreyMatic is a range of 2K primer surfacers suitable for a wide range of repair work. Versatile,
More informationMarch 2013 Product Information GRS Deltron BC
GLOBAL REFINISH SYSTEM March 2013 Product Information GRS Deltron BC Basecoat colour PRODUCTS Deltron Basecoat Tinters Deltron Xirallic Special Effect Tinters Deltron Thinners Deltron BC Fade-out Thinner
More informationTechnical Data Sheet Primers/Surfacers LV 250 Primer EP /005 FOR PROFESSIONAL USE ONLY
100 2505-001/005 50 2505-104 40 2505-204 2505-205 12 Description: Autocoat BT LV 250 Primer EP is a quick drying, chromate-free high solid two-pack epoxy primer-surfacer for shot blasted steel substrates..
More informationMay 2012 Product Information GRS Deltron D800
GLOBAL REFINISH SYSTEM May 2012 Product Information GRS Deltron Clear PRODUCTS Deltron Clear Deltron Medium Solids Hardeners D803, D841, D861 Deltron Accelerated Medium Solids Hardener D864 Deltron Standard
More informationProduct Information DP5000
GLOBAL REFINISH SYSTEM March 2016 Product Information DP5000 (For use with UHS Hardener) PRODUCT DESCRIPTION D8521 Light Grey D8525 Grey D8527 Dark Grey UHS Hardener D8717/18/19 Thinners DP5000 is a range
More informationTechnical Data Sheet Primers/Surfacers LV 350 Primer EP FOR PROFESSIONAL USE ONLY
4 3505-002 1 3505-105 0.5 3505-204 Description: High solid two-pack epoxy primer-surfacer providing excellent appearance and corrosion protection. The target use for this product is refinishing and refurbish
More informationProduct Data Sheet March 2015
Product Data Sheet March 2015 INTERNATIONAL MASTER FOR PROFESSIONAL USE ONLY 2K HS Plus Express Clearcoat P190-6659 Product Product Description P190-6659 is a fast drying high solids 2-pack express clearcoat.
More informationnax Pro LV3601/03/05 VHS Primer Surfacer
Description VOC compliant, quick-drying multi grey shade, two-pack wet on wet and sanding primer surfacer, with excellent application and sanding properties. Helps to reduce process time and provides good
More informationProduct Information FILLERS
GLOBAL REFINISH SYSTEM February 2010 Product Information FILLERS PRODUCTS Galvaplast 77 - Multi Purpose Polyester A656 Multi Purpose A722 - Flexible Polyester Putty - Standard Polyester A1 - Polyester
More informationnax Urethane Primer Surfacer Zitan
Description Quick-drying two-pack wet on wet primer surfacer and sanding primer filler with excellent application and sanding properties. Helps to reduce process time due to its wide application window
More informationFull Product Name. Products. Properties. 2K Etch Primer. Type of Product Description
Product Name Full Product Name Type of Product Description 2K acid etch primer Concept is an acid containing etch and primer in one product. This Product is characterized by excellent adhesion and corrosion
More informationUse suitable respiratory protection Akzo Nobel Sign Refinishes recommends the use of a fresh air supply respirator.
Description A two-component high solids, low VOC, HAPs free epoxy primer. Grip-Gard Epoxy Sealers White and Gray are fast drying primers with excellent corrosion protection over multiple substrates. The
More information8-746 High Production Non-Sanding Primer Grey GS907
8-746 Grey GS907 GENERAL INFORMATION 8-746 Grey GS907 is a multi use polyurethane High Solid (wet on wet) primer. This primer can be used as a general non sanding primer or for properly cleaned ridged
More informationTECHNICAL DATA SHEET 9008B0900D. Desothane HD 9008B0900D Buffable Clear Coat. Product Description. Components. Specifications
TECHNICAL DATA SHEET Product Description Desothane HD is a buffable clear coat intended to be used over Desothane HD 9008 Basecoat. can also be used as a buffable clear coat over pigmented polyurethane
More informationE380 and E381 Epoxy Primer
Description E380 is a high solids 3.5 VOC epoxy primer/sealer, which provides excellent filling over sand blasted metals. E380 dries fast while still maintaining good hold out and a smooth finish. E380
More informationnax K Premium Primer
Description Premium quality, high build multi grey shade fast drying, 2K sanding primer filler with excellent application and sanding properties. Due to its fast ambient drying, it helps to reduce process
More informationPercoTop PUR 2K MS Topcoat
Features is a 2K topcoat based on acrylic and polyester resins. It has an excellent mechanical and chemical resistance. The topcoat is easy to apply. 5 gloss levels: high gloss to matt. Products Base Paint
More informationTechnical Data Sheet.
Technical Data Sheet. Permasolid HS Premium Surfacer 5310. Permasolid HS Premium Surfacer 5310 is a very high-grade two-pack HS sanding surfacer based on acrylic resins. very long application time ideal,
More informationAerodur 3001 Base Coat Special Effects
Technical Data Sheet Product Group Polyurethane Topcoats Characteristics Product Information Aerodur 3001 topcoat is part of the high solid 3 components polyurethane Aerodur 3001 Solid Colors Aerodur 3001
More informationTechnical Data Sheet.
Technical Data Sheet. Permasolid HS Express Surfacer 5250. Permasolid HS Express Surfacer 5250 is a high-grade, productive, VOCcompliant 2K HS sanding surfacer based on acrylic resins. Very good application
More informationPercoTop 449 2K Structure Topcoat
Features is a polyurethane based 2K structure topcoat with a high mechanical resistance. It has an excellent resistance to solvents and other chemicals. Different structures can be produced (cf. PercoTop
More informationCV116 Polyurethane Coat Gloss
Polyurethane Coat Gloss TECHNICAL DATA SHEET Product Description Components is a two pack, ambient curing clear polyurethane gloss coating, designed for internal / external use to protect identification
More informationTechnical Data Sheet.
Technical Data Sheet. Permasolid HS Premium Surfacer 5310. Permasolid HS Premium Surfacer 5310 is a very high-grade two-pack HS sanding surfacer based on acrylic resins. very long application time ideal,
More informationVolume Solids % Weight Solids %
Product Name Full Product Name Type of Product Description HS 2K Primer (High Build) 2K high build acrylic urethane primer surfacer Concept HS 2K Primer (High Build) is a high solid 2K acrylic urethane
More informationVolume Solids %
Product Name Full Product Name Type of Product Description 2K acrylic urethane solid topcoat Concept is a 2 K Solid tinting system. It incorporates a large range of colour formulations, with high opacity
More informationTechnical Data Sheet ACRYLIC FILLER 4:1 Acrylic filler with anti-corrosion additives RELATED PRODUCTS. Acrylic and polyurethane thinner
Acrylic filler with anti-corrosion additives RELATED PRODUCTS Acrylic filler hardener Acrylic and polyurethane thinner PROPERTIES A product designed and dedicated for renovation of classic cars Universal
More informationmm bar at the air inlet minutes at 20 C 5-10 minutes at 20 C. 8 hours at 20 C 45 minutes at 60 C 3 coat application
Description Two-pack, VOC compliant, chromate-free epoxy primer-surfacer with good adhesion and corrosion resistance properties on all substrates within the Car Refinish market. For both new panels and
More informationRAPTOR EPOXY PRIMER RAPTOR 4:1 ANTI-CORROSIVE EPOXY PRIMER DESCRIPTION
Suitable as a primer or as a primer filler for industrial refinish applications, the primer also provides excellent anti-rust protection. Easy to apply Excellent anti-corrosion resistance Can be applied
More informationPrimer / Primer Surfacer
Description is gray in color offering good filling and sanding properties, excellent holdout, fast dry, and good adhesion on properly prepaired substrates. can be used as either a high build primer / primer
More informationF565 Intermediate Coatings (EMEA)
TECHNICAL DATA SHEET Product Description Components is a two pack, pigmented, polyamide based coating formulated for use as intermediate coats in selectively strippable finish paint systems. High resistance
More informationBig Sky Product Information Sheet. Epoxy Prime Primer/Sealer PS3042 (Lt. Gray) PS3044 (Dk. Gray) PS3045 (Black) PS3047 (Yellow Oxide)
Big Sky Product Information Sheet TECHNICAL SUPPORT ((800) 328-4892 P.I. Sheet #3008 Epoxy Prime Primer/Sealer PS3042 (Lt. Gray) PS3044 (Dk. Gray) PS3045 (Black) PS3047 (Yellow Oxide) READ ENTIRE PRODUCT
More informationApply a high gloss color coat: LV650 Topcoat or LV650 Basecoat per TDS. Flash a minimum of 20 minutes before LV650 LumiCoat High Gloss application
Description Autocoat BT LV650 Infuse LumiCoat is a high gloss, two-component polyurethane topcoat that offers the ability to add reflectance or brilliance to any Autocoat BT LV650 color. LumiCoat is part
More informationTechnical Data Sheet.
Technical Data Sheet. Permasolid HS Automotive Top Coat 275. Permasolid HS Automotive Top Coat 275 is a High-Solid top coat system for solid colours. It is used for passenger car finishes. The comprehensive
More informationProduct Data Sheet May 2006
Product Name/Product Code H4530 Product Data Sheet May 2006 INTERNATIONAL MASTER FOR PROFESSIONAL USE ONLY 2K Single Layer Solid Colour System Medium Solids Product Description P420-2K Solid Colour Mixes
More informationDesobond CA102 Adhesive Bonding Primer
TECHNICAL DATA SHEET Product Description Components Desobond is a low density adhesion promoter. It was developed to improve bonding characteristics to aged primers, topcoats, acrylics, aluminum, and other
More informationProduct Information. 2K Chromatic Sealer NR (National Rule) D8081 White D8088 Red D8085 Gray D8089 Yellow D8087 Black D8090 Blue. Product Description
Product Information 2K Chromatic Sealer NR (National Rule) D8081 White D8088 Red D8085 Gray D8089 Yellow D8087 Black D8090 Blue Product Description The 2K Chromatic Sealer NR (D80xx) is a premium quality
More informationPrimer Surfacer EP II
Description Surfacer EP II is a gray, 4.6 lbs/gal, chromate-free epoxy primer that can be applied as a sprayable sanding surfacer, rollable sanding surfacer or primer sealer. This product provides good
More informationTechnical Data Sheet.
Technical Data Sheet. Permasolid HS Clear Coat 8035. Permasolid HS Clear Coat 8035 is a VOC-compliant, high-grade, productive High Solid clear coat. Efficient application in 1.5 coats Versatile in use
More informationAutowave 3 Stage Application and Repair
Description The term spot repair refers to all repairs in which the repaired area has color blended invisibly into the existing finish. As a result, the car refinisher is not compelled to spray large panels
More informationProduct Information. ECP11 White, ECP15 Gray, ECP17 Black A-Chromatic Surfacer
Product Information ECP11 White, ECP15 Gray, ECP17 Black A-Chromatic Surfacer Product Description A-Chromatic Surfacers ECP11 White, ECP15 Gray, ECP17 Black are premium quality low VOC primer surfacers,
More informationPrimer Pro FOR PROFESSIONAL USE ONLY. Description. As A Primer Surfacer. Mixing 4 1 1
08/09/206 Description is a high solids urethane surfacer and sealer. Depending on the mixing ratio utilized, can be either used as a high build surfacer or wet-on-wet primer sealer. is available in white,
More information10P20-44MNF High Solids Epoxy Primer
Technical Data Sheet Product Group High solids epoxy primer Characteristics Product Information A high solids urethane compatible, Skydrol resistant primer for application to aircraft exterior surfaces.
More informationD895 EU-113. Colour Blender. Preparation of Substrate: Required Products. Product Description:
Product Description: GLOBAL REFINISH SYSTEM is a multipurpose product used with Global Refinish System BC colour. Mixed ready-to-spray with BC Colour, it is used as a blending clear along the colour blend
More informationApplication and Repair of Autobase Plus Red Tri-Stage Colors
Description Sikkens Autobase Plus Ready Mix (RM) Groundcoat and Midcoat are a unique color package that requires a specialized blend of pigments and toners designed to provide a color match for FA12:RR.
More informationMix Ratio (by volume) 7630/3600 (Base) 0830/9000 (Acid Catalyst) Metal Primer 6840B meets the technical requirements of: Mil-P-7962 Mil-C-15328
TECHNICAL DATA SHEET Product Description 6840B is a two component chromated etch primer designed to give adhesion and corrosion protection to aluminium alloys as part of the 4080 series scheme. Alternative
More informationProcess Data Sheet January 2015
Process Data Sheet January 2015 INTERNATIONAL MASTER FOR PROFESSIONAL USE ONLY J1005V TCB100 - Aquabase Plus Clean Vivid Ruby Special Concentrate P190-1005 EMEA Product Description P190-1005 Clean Vivid
More informationSEA45 Water Borne Acrylic Gloss
Water Borne Acrylic Gloss TECHNICAL DATA SHEET Product Description Components is a single pack, general purpose gloss finish. Applicable by brush or spray. Fast drying Water based, low VOC Excellent weather
More informationFOR PROFESSIONAL USE ONLY
100 3506-001 20 3599-104 40 3506-204 3505-205 23 Description: High performance, fast drying two-pack non-sanding filler or sanding filler. The target use for this product is refinishing and refurbish of
More informationGray Urethane Surfacer (Low VOC)
Description Lesonal is intended for use as a high build surfacer that offers excellent filling, easy sanding, and fast dry times. Depending upon the mixing ratio used, Lesonal can also be used as a wet-on-wet
More informationProduct Data Sheet July 2014
Page 1 of 5 Product Data Sheet July 2014 INTERNATIONAL MASTER FOR PROFESSIONAL USE ONLY 2K HS Clearcoat P190-6850 Product Description P190-6850 2K HS Clearcoat P210-842 2K HS Hardener Fast P210-8430 2K
More information2K weather resistance clear coat A850
Clear coat Donglai Coating Technology (Shanghai) Co., Ltd. 2K weather resistance clear coat A850 Description High-build, two-component clear coat designed for universal application and optimal appearance
More informationPermasolid HS Vario Surfacer 8590
Permasolid HS Vario Surfacer 8590 GENERAL DESCRIPTION A high quality acrylic surfacer from our 2K-Acryl-System for partial and full passenger car refinishes. Its versatility enables application at both
More informationHigh-quality, water-dilutable satin gloss enamel on the basis of a modified alkyd technology.
Product Data Sheet High-quality, water-dilutable satin gloss enamel on the basis of a modified alkyd technology. ralstoncolour.com /picto Excellent outdoor resistance Excellent flow and optimal hiding
More information5543/9000 Flame Retardant UV Resistant Varnish High Gloss
Flame Retardant UV Resistant Varnish High Gloss TECHNICAL DATA SHEET Product Description is a two component, transparent, glossy acrylic urethane varnish. Designed to provide UV protection to external
More informationPRODUCT GUIDE: COMPLIANT TOPCOATS. Version:
PRODUCT GUIDE: COMPLIANT TOPCOATS Version: 08.07.17 EAGLE BRIDGES PRODUCT DATA PRODUCT: 3.5 V.O.C FASTDRY, Black Product Number: 4899 DESCRIPTION: This product is a high gloss enamel for OEM finishing
More informationADLER 2K-Fenstergrundlack
ADLER 2K-Fenstergrundlack 69511 ff Solvent-based white primer and intermediate coat for industrial and professional use PRODUCT DESCRIPTION General Special Properties and Standards Application area Solvent-based,
More informationGRIP-GARD BC Translucent For Professional Use Only
Description Grip-Gard BC uses a specially blended binder which converts Grip-Gard BC toners into a fast drying, durable backlit sign coating. With this system, backlit plastic signs can be painted quickly
More informationPermasolid HS Premium Surfacer 5310
Permasolid HS Premium Surfacer 5310 GENERAL DESCRIPTION A high quality, high solids 2K acrylic surfacer for passenger car refinishing that provides very high film build with good vertical stability, efficient
More informationBC Translucent uses a specially
Grip-Gard BC Translucent Description Technical Data Sheet October 2013 Topcoat Grip-Garinto a fast drying, durable backlit sign coating. With this system, backlit plastic signs can be painted BC Translucent
More informationN39/1794 Clear Acrylic Lacquer TECHNICAL DATA SHEET N39/1794. Product Description. Components. Specifications. Surface Preparation and Pretreatment
Clear Acrylic Lacquer TECHNICAL DATA SHEET Product Description is a single pack, acrylic lacquer designed to protect identification markings, labels and emblems on aircraft. Fast drying Excellent flexibility
More informationTechnical Data Sheet.
Technical Data Sheet. Permasolid HS Diamond Clear Coat 8450. Permasolid HS Diamond Clear Coat 8450 is a VOC-compliant High Solid clear coat. It is used to repair vehicles which in production line are coated
More informationMetal 3in1. Applied directly to rust A smooth gloss anti-rust enamel paint for metal surfaces
Applied directly to rust A smooth gloss anti-rust enamel paint for metal surfaces It prevents humidity from penetrating, providing long-lasting rust protection Highly resistant to ultraviolet radiation,
More informationDULUX UNIVERSAL UNDERCOAT
TECHNICAL DATA SHEET Version 1 2015 JUNE THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION Intermediate coating for use under decorative topcoats, for interior and exterior use PRODUCT
More informationTechnical Data Sheet.
Technical Data Sheet. Permasolid HS Diamond Clear Coat 8450. Permasolid HS Diamond Clear Coat 8450 is a VOC-compliant High Solid clear coat. It is used to repair vehicles which in production line are coated
More informationData Sheet 5741 Englisch
Data Sheet 5741 Englisch 2K-PUR-Acryl Silk Gloss 2K-PUR-Acryl Seidenglanzlack 5741 two-component, high mechanical resistance, for exterior and interior use, with 2K-PUR-Acryl Hardener 5770 2K-PUR-Acryl
More informationGen2O - Environmentally Friendly
Waterborne Automotive Basecoat: Go for Gen2O and build a future for your business that makes cents. Gen2O is user friendly and cost effective. The transition from conventional to Gen2O is easy. Only minor
More informationProduct Information. ECP11 White, ECP15 Gray, ECP17 Black A-Chromatic Surfacer. Product Description. Preparation of Substrate
Product Information ECP11 White, ECP15 Gray, ECP17 Black A-Chromatic Product Description A-Chromatic s ECP11 White, ECP15 Gray, and ECP17 Black are premium quality, low VOC primer surfacers specifically
More informationP Waterborne Primer-Surfacer-Grey
PDS N4.15C January 2014 P950-5505 Waterborne Primer-Surfacer-Grey PRODUCT DESCRIPTION P950-5505 Waterborne Primer-Surfacer is a grey primer-surfacer based on the latest 1K waterborne technology for spot
More informationAutobase Plus FOR PROFESSIONAL USE ONLY. Description. Basecoat 09/16/2015
Description Autobase Plus solvent borne basecoat provides excellent coverage, metallic control and sprayability when used to duplicate OEM solid, metallic and pearl color effects. Autobase Plus must be
More informationTECHNICAL DATA SHEET (EMEA)
Desothane HS Polyurethane Aerosol Touch Up TECHNICAL DATA SHEET (EMEA) Product Description Components is CA8000 supplied in aerosol form. is a polyurethane topcoat for the protection and decoration of
More informationTECHNICAL DATA SHEET 515X349. DeSoto 515X349 Exterior Primer. Product Description. Components. Specifications
TECHNICAL DATA SHEET Product Description DeSoto exterior primer is a conventional solids urethane compatible epoxy coating. This primer was formulated to protect aluminum and composite substrates from
More informationPRODUCT GUIDE: CATALYZED TOPCOATS. Version:
PRODUCT GUIDE: CATALYZED TOPCOATS Version: 08.07.17 ELITE COATINGS PRODUCT DATA PRODUCT: Low VOC High Solids Aliphatic Urethane Product Number: 4045 DESCRIPTION: 4045 is a top of the line 2 component urethane
More informationProduct Data Sheet Awlwood MA Primers OJ3809 / OJ9809 / OJ7809 Specification Data
Specification Data Packaging: Product Code: Cleaning: Available in 1 quart packs OJ3809 Clear; OJ9809 Yellow; OJ7809 Red OT0200 Awlwood MA Brush Cleaner Volume Solids: 45% Specific Gravity: OJ3809-1.013
More informationAquaCLAD Water-Reducible Rust Preventative Alkyd
AquaCLAD 1600 Water-Reducible Rust Preventative Alkyd A rust preventative coating for interior and exterior steel in mild to moderate industrial environment. Recommended For Features Refinish Market High
More informationPRODUCT GUIDE: CATALYZED PRIMERS. Version:
PRODUCT GUIDE: CATALYZED PRIMERS Version: 08.07.17 305 Zinc Rich Epoxy Polyamide Primer Description: 305 is a user friendly zinc-rich epoxy primer formulated for use as a primer under acrylic, epoxy, and
More informationPRODUCT GUIDE: WATERBORNE TOPCOATS. Version:
PRODUCT GUIDE: WATERBORNE TOPCOATS Version: 08.07.17 EAGLE BRIDGES PRODUCT DATA PRODUCT: CONTAINER GUARD QD BLACK PRODUCT: 4886-02 DESCRIPTION: CONTAINER GUARD QUICK DRY (QD) is an air-drying, water reducible
More informationSketchpaint. Ideal for turning any smooth surface into a whiteboard. Ready to use in 5 days
Sketchpaint Ideal for turning any smooth surface into a whiteboard SketchPaint - A whiteboard straight out of a tin! White Gloss or Transparent Finish Simple application Tin size available: 3m² or 6m²
More informationPRODUCT DESCRIPTION High quality interior or exterior enamel for surfaces where a glossy durable finish is required
TECHNICAL DATA SHEET Version 1 2016 JULY THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION High quality interior or exterior enamel for surfaces where a glossy durable finish is required
More information2014 Sign Traini GRIP-GARD BC SYSTEM GRIP-GARD BC FLEX
2014 Sign Traini GRIP-GARD BC SYSTEM GRIP-GARD BC FLEX PICTOGRAM DESCRIPTION Degrease Machine sand dry Hand sand wet Hand sand dry Scotch Brite Use Akzo Measuring Stick Ready to Spray Mixing Ratio: 2
More informationMagnetpaint & Sketchpaint
Magnetpaint & Sketchpaint Turn any smooth surface into a magnetically receptive whiteboard MagnetPaint is an exciting product that allows you to paint your own magnetic surface on any flat area. SketchPaint
More informationUnit PO0205K Knowledge of Applying Fillers and Foundation Materials
Assessment Requirements Unit PO0205K Knowledge of Applying Fillers and Foundation Materials Content: The types of substrates likely to be found in vehicle refinishing a. List types of substrate to include:
More informationCUPRON NEXT TECHNICAL DATA SHEET
Product description New hard matrix antifouling paint free of copper and organostannic compounds. It provides good seasonal protection for boats that work even in particularly hot and aggressive waters.
More informationDPS3051 White / DPS3055 Gray / DPS3057 Dark Gray
V-PRIME DPS3051 White / DPS3055 Gray / DPS3057 Dark Gray V-PRIME DPS305x are premium quality primer surfacers available in white, gray and dark gray. The surfacers are suitable for the wide range of day-to-day
More informationDPLV Low VOC Epoxy Primer P-245
Low VOC Epoxy Primer P-245 Low VOC Epoxy Primer provides excellent adhesion and corrosion resistance to many types of properly prepared steel, aluminum, and fiberglass substrates. Epoxy Primer may also
More informationHAMMERITE DIRECT TO RUST HAMMERED AND SMOOTH
TECHNICAL DATA SHEET Version 1 2016 June THIS ISSUE SUPERSEDES ALL PREVIOUS PUBLICATIONS PRODUCT DESCRIPTION A corrosion resistant and decorative coating for ferrous and nonferrous metals, wood and certain
More informationQuality Marine Equipment Since Antifouling Paint For Metal Under The Waterline SPRAY. Application Instructions.
Quality Marine Equipment Since 1981 Antifouling Paint For Metal Under The Waterline SPRAY Application Instructions www.antifoulingpaint.net Thank you for selecting Velox Plus Antifouling Paint to protect
More information8340/2320 Temporary Anti-Corrosion Coating. Durable protection, scratch resistant Humidity and fluid resistant Easily removable coating
Temporary Anti-Corrosion Coating TECHNICAL DATA SHEET Product Description is a temporary anti-corrosion coating removable with the help of aqueous alkaline solution. is designed to protect individual aircraft
More informationUNIT TITLE: KNOWLEDGE OF APPLYING FILLERS AND FOUNDATION MATERIALS
UNIT REF: PO0205K UNIT TITLE: KNOWLEDGE OF APPLYING FILLERS AND FOUNDATION MATERIALS Level: 2 Route: Knowledge Credit Value: 6 GLH: 45 Mapping: This unit is mapped to the IMI NOS PO2 and PO5 Rationale:
More informationSample Test Project. Category: Transportation & Logistics. Regional Skill Competitions - Level 3. Skill Car Painting
Sample Test Project Regional Skill Competitions - Level 3 Skill- Car Painting Category: Transportation & Logistics 1 Table of Contents A. Preface... 3 B. Test Project... 4 C. Marking Scheme... 6 D. Infrastructure
More informationDPS3051 White / DPS3055 Gray / DPS3057 Dark Gray
V PRIME Acrylic Urethane Surfacer P 238 DPS3051 White / DPS3055 Gray / DPS3057 Dark Gray V PRIME DPS305x are premium quality primer surfacers available in white, gray and dark gray. The surfacers are suitable
More information