FOR PROFESSIONAL USE ONLY

Transcription

1 Description: High performance, fast drying two-pack non-sanding filler or sanding filler. The target use for this product is refinishing and refurbish of existing vehicles and the painting of newly build commercial vehicles and trailers. The EU VOC limit for this product (product category: IIB.C) in ready to use form is max 540 g/litre. The VOC content of this product in ready to use form is max 540 g/litre. (suction feed) 2-3* mm 3-5 bar Product and Additives: Autocoat BT LV 350 Filler Beige/Light Gray/ Dark Gray Autocoat BT LV 350 Hardener Medium Autocoat BT LV 350 Filler Hardener Sanding Autocoat BT LV 350 Filler Reducer Medium Autocoat BT LV 350 Filler Reducer Slow Autocoat BT LV 351 Hardener Hi-Flo mins. 40 mins 20 C WB 551 Basecoat RM / Autowave Basic Raw Materials: Autocoat BT LV 350 Filler Beige/Light Gray/Dark Gray : acrylic resin Autocoat BT LV 350 Hardener Medium : poly-isocyanate resin Autocoat BT LV 350 Filler Hardener Sanding : poly-isocyanate resin Autocoat BT LV 350 Filler Reducer Slow/Medium : solvents Autocoat BT LV 351 Hardener Hi-Flo : poly-isocyanate resin Suitable Substrates: Existing finishes, including finishes with thermoplastic behavior Autocoat BT 800 Washprimer AS Autocoat BT 800 Washprimer Beige Autocoat BT Washprimer Red Autocoat BT LV 850 Washprimer CF Autocoat BT LV 851 Washprimer AS Autocoat BT LV 250 Primer EP / Primer EP Varicolor Autocoat BT LV 350 Primer EP Sikkens polyester bodyfillers and Polysurfacer Polyester laminates and plywood Wood Surface Preparation: Existing finishes: Degrease with LV 350 Antistatic Silicon Remover and dry sand with P grit. Sikkens polyester bodyfillers: Dry sand with P grit. Polyester laminates and plywood: Degrease with LV 350 Antistatic Silicone Remover and dry sand with P280 grit. Wood: Dry sand with P180 grit to achieve a smooth surface and to remove any loose fibers. 1/5

2 Tinting: LV 350 Filler Beige/ Light Gray can be tinted with LV Topcoat without hardener up to 10 parts by volume. LV 350 Filler Dark Gray may not be tinted Mixing Ratio by Volume: A. Non sanding filler: 100 parts of LV 350 Filler Beige/Light Gray/ Dark Gray 20 parts of LV 350 Hardener Medium or LV 351 Hardener Hi-FLo 40 parts of LV 350 Filler Reducer Medium/Slow Use mixing stick # 23 B. Sanding filler: 100 parts of LV 350 Filler Beige/Light Gray/ Dark Gray 50 parts of LV 350 Filler Hardener Sanding 25 parts of LV 350 Filler Reducer Medium/Slow Use mixing stick # 11 Spraying Viscosity: Mixture A: s DIN Cup 4 at 20 C Mixture B: s DIN Cup 4 at 20 C Potlife: Mixture A: 1½-2 hours at 20 C Mixture B: 1-1½ hours at 20 C Spray gun fluid tip and working pressure: Spray Gun: Fluid Tip: Working Pressure: Gravity feed: mm 3-5 bar Gravity feed HVLP: mm max. 0.7 bar Suction feed: mm 3-5 bar Suction feed HVLP: mm max. 0.7 bar Pressure feed: mm ± 1.0 bar material pressure Application Process: Non sanding filler: Spray one or two single wet coats. In case of two coats, allow a flash-off time of at least 5-10 minutes between coats. 2/5

3 Sanding filler: Apply two or three coats, allow a flash-off time of at least 5-10 minutes between coats. When the LV 350 Filler Beige is used under LV 250, the Filler has to be applied until full opacity is reached. Film Thickness: Non sanding filler : µm for each coat Sanding filler : µm for each coat Cover rate: m²/liter Ready for use mixture at 1 µm dry film thickness, Sanding: ± 404 Non Sanding: ± 417 Note: The practical cover rate depends on many factors i.e. shape of the object, roughness of the surface, application method and application circumstances. Cleaning of Equipment: Use Sikkens Solvent, a nitrocellulose thinner or Autocoat BT LV 350 Filler Reducers. Drying times non sanding: Minimum time to recoat with: 10 C: 20 C: LV 350 Filler Reducer Medium : 55 mins 40 mins LV 350 Filler Reducer Slow : 1,5 hour 55 mins Maximum time to recoat with: 20 C: - WB 551 Basecoat RM / Autowave 6 hrs - Autocoat BT LV Topcoats 24 hrs Notes: 1. When 2 or more coats are applied, extend the total flash off time before Topcoat to 50 mins / 20 C 2 If the drying times are exceeded, LV 350 Filler Beige/Gray/Dark Gray has to be dry sanded with P grit prior to being recoated with a finish. 3. LV 350 Filler Beige/Gray/ Dark Gray can be recoated with itself within 24 hours. 4. If dust ingress occurs in the LV 350 Filler Beige/Gray/Dark Gray, it can be denibbed carefully with sandpaper, either after a drying time of 3 hours at 20 C or 30 minutes at 60 C. Drying times sanding filler: 20 C 60 C Overnight 1 hour Recommended Sandpaper grades: Wet sand: P400-P600 followed by P800-P1000 Dry sand : P280 grit followed by P360-P400 3/5

4 Recoatable with: LV 250 Topcoat MM/RM LV 250 Topcoat IC RM LV 350 Topcoat MM/RM LV 351 Topcoat MM/RM Autocoat BT WB 551 Basecoat RM / Autowave WB 450 UBC Coating Autocoat BT 800 Metallics Packaging: 5L in 5-liter can Shelflife: Autocoat BT LV 350 Filler Beige/Gray Autocoat BT LV 350 Filler Dark Gray Autocoat BT LV 350 Hardener Medium Autocoat BT LV 350 Filler Hardener Sanding Autocoat BT LV 350 Filler Reducer Medium Autocoat BT LV 350 Filler Reducer Slow Autocoat BT LV 351 Hardener Hi-Flo : 2 years : 1 year : 1 year : 1 year : 4 years : 4 years : 1 year Color: Beige, Light Grey or Dark Gray HEALTH & SAFETY DATA regarding Autocoat BT LV 350 Filler Beige/Gray/Dark Gray : For professional use only. (See Material Safety Data Sheet). See text on the label of this product. The user of this product is required to comply with the national statutory regulations for health and safety at work and waste disposal. 4/5

5 AkzoNobel Coatings LTD Car Refinishes AkzoNobel CR Ireland Address: 136 Milton Park, Abingdon Address: Avonbeg Industrial Estate Oxfordshire OX14 4SB Long Mile Road, Dublin 12 Tel: (0) Tel: (0) IMPORTANT NOTE The information in this data sheet is not intended to be exhaustive and is based on the present state of our knowledge and on current laws: any person using the product for any purpose other than that specifically recommended in the technical data sheet without first obtaining written confirmation from us as to the suitability of the product for the intended purpose does so at his own risk. It is always the responsibility of the user to take all necessary steps to fulfill the demands set out in the local rules and legislation. Always read the Material Data Sheet and the Technical Data Sheet for this product if available. All advice we give or any statement made about the product by us (whether in this data sheet or otherwise) is correct to the best of our knowledge but we have no control over the quality or the condition of the substrate or the many factors affecting the use and application of the product. Therefore, unless we specifically agree in writing otherwise, we do not accept any liability whatsoever for the performance of the product or for any loss or damage arising out of the use of the product. All products supplied and technical advices given are subject to our standard terms and conditions of sale. You should request a copy of this document and review it carefully. The information contained in this data sheet is subject to modification from time to time in the light of experience and our policy of continuous development. It is the user's responsibility to verify that this data sheet is current prior to using the product. Coatings brand names mentioned in this data sheet are trademarks of or are licensed to AkzoNobel. Head Office Akzo Nobel Car Refinishes B.V., PO Box BA Sassenheim, The Netherlands. 5/5