GHIBLY ETOILE Glitter effect decorative coating, with particular light and colors, depending on observation corner

Size: px

Start display at page:

Download "GHIBLY ETOILE Glitter effect decorative coating, with particular light and colors, depending on observation corner"

Eric Robbins
5 years ago
Views:

Destination Revision 1 fro 0/09/2016 For indoor.

Charactreistcs Excellent chromatic resistance Excellent adhesion Easy to apply Excellent coverage Good washability Extraordinaty colors effects VOC (Directive 2004/42/CE) ( g/l ) <Decorative

g/l Recommended surface and temperature conditions Reccomendations Avoid applications at room temperatures lower than +10 C or higher than +3 C and relative humidity higher than 80%.

Avoid application on chalking surfaces if not peviously treated with fixatives model FIXODIL for outdoors or Acrilan 3470 for indoors. WARNING:ventilate the room to avoid humidity accumulation.

In presence of moulds, use antimolds detergents and fixing elements.

1 Destination Revision 1 fro 0/09/2016 For indoor. Suitable as decorative finish for domestic environments and for community sites : hotel, disco, pubs, restaurants, to realise a unique decoration, particluar and reflective. Charactreistcs Excellent chromatic resistance Excellent adhesion Easy to apply Excellent coverage Good washability Extraordinaty colors effects VOC (Directive 2004/42/CE) ( g/l ) <Decorative effects paintings.eu limit value for this product (Cat. A/l): 220g/l (2010). This product cointans max. g/l Recommended surface and temperature conditions Reccomendations Avoid applications at room temperatures lower than +10 C or higher than +3 C and relative humidity higher than 80%. Check the surfaces suitability referred to the humidity degree with hygrometer. Support temperature: min +10 C, max +3 C. Avoid application on chalking surfaces if not peviously treated with fixatives model FIXODIL for outdoors or Acrilan 3470 for indoors. WARNING:ventilate the room to avoid humidity accumulation. WARNING:the maximal washability is obtainable after 710 days from application. Completely eliminate preexistent solvent paintings. Remove, wet sanding or brushing, the possible efflorescences. In presence of moulds, use antimolds detergents and fixing elements. Well mix the product before use The applications must not be executed on walls directly exposed to the sun or with room temperatures under + C. In case of doubt, with old chalking or just a little cohesive paintings, evaluate the first coat dillution. Apply the fixative primer on a little surface portion and after at least 12 hours make an adhesion test. The chromatic effet depends on different factors. It can result different, characterized by shades depending onn the decorator skills. It is also influenced by the surface absorption characteristics and by the environmental conditions surrounding the application and drying phases of the painting. Page 1/

2 Application cycle Revision 1 fro 0/09/2016 Never painted interior walls In case of new civil plasters let it age at least 28 days ( T= 20 C and U.R. < 7%) before any operation. Carefully brush. Remobe bad anchored parts, dust and dirt. Level imperfections with STUCOL. After 8 hours sand the stuccoed parts and clean them carefully. Be sure that the wall is dry. Verify surfaces idoneity according to humidity degree with match test or hygrometer. Application of water fixative as ACRILAN Application of MICROPRIMER diluted at 10 12%. Wait 24 hours and then apply GHIBLY ETOILE diluted at 10 1% with water by using a short hair roll or a croddes hands paintbrush. Once the wall is dry, apply the second coat with spalter, but diluting with 2 30% of water. In order to improve the reflectance of the light spots and make clearer the glitter brillance, treat the surface of the dry product with a dry synthetic sponge, with circular with a light pressure. Another way to point out the glitter is the use of dry spalter after approx min during the drying phase. Already painted interior walls with tempera paintings Carefully clean the surface from dust or dirt. With molds or fungi disinfect the surfaces with SESTRICID. Level imperfections with STUCOL. After 8 hours sand the stuccoed parts and clean them carefully. Insulate the surgace with solvent fixative as FIXODIL. Apply MICROPRIMER diluted at 1012% After 24 hours apply by choosing one of the modalities described above. Page 2/

3 Application cycle Revision 1 fro 0/09/2016 Already painted interior walls with washable hydropaintings Carefully clean the surface from dust or dirt. With molds or fungi disinfect the surfaces with SESTRICID. Level imperfections with STUCOL. After 8 hours sand the stuccoed parts and clean them carefully. Apply water fixative as ACRILAN Apply MICROPRIMER diluted at 10 12%. After 24 hours apply by choosing the modalities described above. Characteristics and technical informations Data observable at T=20 C and 60% relative humidity Tin aspect RESIN Color Liquid, thixotropic neutral Glitter effect Paints achievable with MW2 tintometric system Use Brush Roll Sponge Spalter Page 3/

4 Revision 1 fro 0/09/2016 Thinner Tools' cleaning Application process Brush Thinner (% Volume) 10 1 (1 mano) ; 2 30 (2 mano) TECHNICAL DATA Mass density ( kg/l ) 1,00 Solids content by vol. ( % ) Brooklfield viscosity (cp) 2 Brilliance ( % ) Touch dry ( h ) Depth dry ( days ) recommended dry film thickness (dtf) ( µm ) Theoretical spreading rate ( mq²/lt ) Complete polymerisation days Recoating interval ( h ) Minimum film temperature ( C ) Satin STORAGE (dry and cool place) 12 months in tightly closed package, protected from frost and heat sources Page 4/

5 Revision 1 fro 0/09/2016 Storage temperature ( C ) Unit size 1 2, lt Safety instructions Products must be treated with attention, avoid the skin contact. Users will have to follow the actual laws. Actions as wet sanding, sanding, removal with flame, etc. of old painting coats can geerate dust and dangerous smokes. Work in well areated areas and wear the adequate individual protection means. In Italy Decree 303 and 47 concern the rules valid for the application operations. For further information concerning the right product elimination, storage and manipulation please consult the relative taìechnical data sheet. Data in this technical sheet are only given for information and are the result of laboratory tets and practical experience, However, the factory is not responsible if the product isn't used under its direct control. SESTRIERE VERNICI Srl Technical Assistance is available to give all information necessary for a correct use of the product. Be careful: the product could show, towards some subject who are particularly sensitive to isothiazolones, a little irritation. It's thus recommended to use gloves and protective glasses and to wash very well the parts which could by chance touch the skin. Page /

IRON MIOX Micaceous iron polish, anticorrosive for iron surfaces with no patchy finish

IRON MIOX Micaceous iron polish, anticorrosive for iron surfaces with no patchy finish Converter name Destination Finish at high anticorrosie powerd given by the high micaceous iron oxyd. Suitable also in marine and iindustrial environment. Applicable on iron and steel surfaces as well as