caulking gun pocket duster brush wire brush filament brush comb ladder bucket canvas drop sheet plastic protection sheet rollers roller frame

Transcription

1 checklist Here at Rokset we know that for the best paint finish you need quality equipment. We have created a painters checklist to assist you before you start your painting job so that you have all the equipment you will need to finish the job. Rokset has a wide variety of the paint application tools available for the tradesperson and the do it yourself painter, please contact us or your local paint specialist for more information. For painting preparation, cleaning and repairs you may need: sanding sponge stripping knife putty knife filling blade set wall stripper sugar soap caulking gun pocket duster brush wire brush filament brush comb ladder bucket roller cleaner putty tack cloth cleaning cloth For painting protection you may need: safety glasses dust masks coveralls canvas drop sheet plastic protection sheet cover quick gloves For painting application you may need: paint mixer rollers paint can opener mini roller complete paint edger paint tray brushes roller frame roller extension pole Remember to use the best painting application tools that you can!

2

3

4

5 painting with rollers Roller sleeves are sold in short, medium and long nap lengths. A Short nap is between 4-8mm long and holds the least amount of paint. This roller is best used with gloss paint on smooth surfaces. It leaves a thin, very smooth coating. A Medium nap is between 8-12mm long and holds any type of paint well. It produces a soft-looking stippled effect perfect for walls and ceilings. A Long nap is between 18-25mm long and holds a heavy load of paint that is ideal for textured, damaged or extremely porous surfaces. Roller Preparation Prior to use rinse rollers in solvent or water, dependent on the paint type, to remove loose fibres. Make sure the roller is dry before use. Loading the Roller with Paint Half fill the well of a roller tray with paint and dip the roller in. The roller should be almost half submerged. Roll off excess paint on the ramp of the tray. Repeat this process until the roller is evenly saturated. Do not overload with paint or the roller will drip and slide, producing an uneven coat. Paint Application with a Roller Start at the top and work your way down. This allows drips to be painted over. To start push roller up and down in a diagonal motion to form an M about a metre wide. Going in the opposite direction form a W to fill the gaps. Keep contact with the surface during this process and apply even pressure for a smooth finish. Next roll in a criss-cross motion to ensure complete coverage. Finish this section by rolling lightly in vertical strokes from the floor to ceiling. When painting a ceiling, finish off by rolling lightly in even strokes towards the ceiling s light source. Move to the next section and repeat above steps. Clean up and care: Never leave a paint-covered roller exposed to air for any length of time. Wrap in a plastic bag or cling wrap to keep moist and ready to be used again. Make sure rollers are cleaned thoroughly after use and stored correctly. See Brush and Roller Care and Cleaning for full cleaning and product care instructions. For professional advice on your particular task, please speak to a paint specialist.

6 painting with brushes my project Paintbrushes are sold in a variety of sizes, 25mm, 38mm, 50mm, 63mm, 75mm, 88mm, 100mm etc. It is often best to use a variety of sizes for your painting project. 25mm-63mm brushes are best used for trim work, joinery, furniture and skirting. 75mm flat brushes for interior walls, ceilings and larger flat areas. 88mm-100mm flat brushes for larger exterior surfaces. Tapered brushes are used for cutting in and for accurate painting. It is important to make sure the brush feels comfortable in your hand regardless of its size. A brush becomes heavier when loaded with paint so remember to allow for this when choosing your brush. Synthetic filament paintbrushes Synthetic filament paintbrushes are now the most common and best suited brush for general painting, especially with water based paints. They are easier to use and clean. In most instances filament lasts longer than natural bristle. Natural bristle paintbrushes Natural bristle paintbrushes are used for all paint types but are particularly suited to oil based paints, stains and industrial coatings. Natural bristle brushes hold more paint, have a softer finish and can be used for a wider range of applications. Brush Preparation Prior to use rinse brushes in solvent or water, dependent on the paint type, to remove any loose bristles. Make sure the brush is dry before use. Loading the Brush with Paint Dip no more than half of the brush bristle into the paint. Tap off excess paint by gently tapping the brush against the side of the paint can. Paint Application with a Brush Start at the top and work your way down. This process allows drips to be painted over. Hold your brush like a pencil to achieve the best control. Apply paint using the brush tips and hold the brush at a 45 degree angle to the surface using an even pressure. Apply paint in long smooth vertical strokes. When painting timber always paint along the grain. Finish off and remove any brush marks by painting from the painted area to the unpainted area and back. This will create a smooth painted finish. Concentrate on one area at a time until evenly covered. Avoid excess re-brushing. Move to the next section and repeat above steps. Cutting In Using a brush paint a mm border around the wall surface. This is known as cutting in. Cut in around power points and light switches using a smaller border of about 25-50mm. When completing your project do not paint over the area that has been cut in by the brush. Clean up and care: Never leave a paint-covered brush exposed to air for any length of time. Wrap in a plastic bag or cling wrap to keep moist and ready to be used again. Never leave a brush in solvent or water for extended periods of time. Make sure brushes are cleaned thoroughly after use and stored correctly. See Brush and Roller Care and Cleaning for full cleaning and product care instructions. For professional advice on your particular task, please speak to a paint specialist.

7 brush and roller care and cleaning Care and Cleaning To ensure brushes and rollers last longer and maintain their original condition they must be cared for correctly. 1. Squeeze as much paint as possible from rollers, brushes and trays back into the paint can for future use. 2. Wipe remaining paint from brush or roller onto an absorbent material such as a rag or newspaper. Allow these materials to dry and dispose of with normal household waste. 3. Wash brush or roller in a large bucket with the solvent recommended for the paint used. 4. Wash brush or roller in a separate bucket of warm, soapy water. 5. Buckets of water and/or solvents should be left to rest overnight so paint sediment can settle to the bottom. When paint has settled water can be poured onto grass or garden. Solvent can be retained for future use. Paint sediment at the bottom of the bucket should be wiped out with an absorbent material such as a rag or newspaper. Allow these materials to dry and dispose of with normal household waste. 6. Shake out excess water from brush or roller. 7. Brushes Comb the bristles of brushes and shape while still wet. Brushes can be stored hanging up or flat, either in their original packaging or in newspaper. Ensure brush bristle or filament is not stored in contact with anything that can distort its shape. Rollers Rollers are best dried and stored standing up to avoid flat spots developing in the nap. Remember to always rinse roller covers in water prior to use to ensure dust and loose fibres do not contaminate your paint. Donts Do not stir paint with a brush or roller, always use a paint mixer. Never let brushes or rollers soak in water for long periods of time, this may distort brush bristle or roller fibres. Never let paint dry on brushes or rollers. Do not use concentrated detergent or very hot water when washing as this may damage brush bristle or roller fibres. Taking a painting break? Simply wrap your brush or roller in a plastic bag or cling wrap to keep moist and ready to be used as soon as your break is over. Paint Disposal If not disposed of correctly waste paint pollutes waterways and can endanger wildlife. Please ensure you follow this advice when disposing of empty paint cans and waste paint. Dispose of rags and newspaper used to clean paint applicators in normal household waste after they have dried. Do not wash brushes and rollers in water that flows directly down drains or gutters. Use buckets and dispose of waste water and paint sediment as specified above. Empty paint cans may be recycled through a certified recycling depot. Contact your local council for more information. Waste paint should be poured into a hole dug into the ground that has been lined with newspaper. The water will drain through the newspaper leaving the paint on top. When paint is dry dispose of newspaper in normal household waste. For professional advice on your particular task, please speak to a paint specialist.

8 exterior walls Little Gem Rough Surface Roller Little Gem H/D Cage Frame LIttle Gem Extension Pole Little Gem Roller Tray Little Gem Opal Wall Brushes Little Gem Opal Wall Cutters Little Gem GP Sponge Flexisand Sanding Sponge Wire Brush Little Gem Stripping Knife Little Gem Cover Quick Rokset Canvas or Plastic Drop Sheet Rokset Tack Cloth or Pocket Duster Always consult your local paint specialist for professional advice on the correct paint to use. Preparation Preparation of the exterior of your home can vary greatly depending on its construction and design. This preparation guide is a general guide for all surfaces. Loose timber boards should be fastened firm. Ensure all nails sit just below the surface. Fill any holes or cracks with the appropriate filler and allow to cure as per instructions. Sand surfaces smooth to remove old paint and sharp edges and to smooth fillers. Always sand along the grain of timber. Use a wire brush followed by a light sanding with a sanding block in areas required coarse sanding. (NB: sanding dust from all surface types can be harmful. Use dust masks, gloves and coveralls to protect yourself and your clothing). Thoroughly wash and degrease surfaces using sugar soap. Allow to dry completely before painting. If necessary, use a moss and mould cleaner prior to painting. Tape up adjoining surfaces and around any fixtures or fittings. Lay drop sheets to protect surrounding areas. Rinse rollers and brushes in solvent or water, dependent on the paint type. Allow to dry before use. Immediately before painting use a tack cloth or pocket duster to remove excess dust and fine particles. Application - continued on next page For professional advice on your particular task, please speak to a paint specialist.

9 exterior walls Application Paint drying times vary depending on temperature. Consult your paint professional for advice on ideal painting conditions. Always take the necessary safety precautions when painting. Remember ladder safety and keep the floor clear to avoid accidents. Start at the top and work your way down. This process allows drips to be painted over. Paint large areas first followed by smaller areas like window and door trims. It is best to remove shutters, screens and blinds and paint them on the ground. Speak to your paint specialist about applying a base coat, primer or rust resistant application. Priming is especially important on surfaces that have never been painted. Using a brush paint a mm border around the area surface. This is known as cutting in. Cut in around window frames, doorways and any fixtures or fittings using a smaller border of about 25-50mm. When completing your project do not paint over the area that has been cut in by the brush. For the best brush finish on large surface areas apply paint in long smooth vertical strokes. When painting timber always paint along the grain. Where possible use rollers as paint will go on faster than with a brush. Finish coating the area as directed in Painting with Brushes or Rollers. When painting: Weatherboards paint the horizontal under edges or vertical side edges first with a small bristle brush. Paint the boards with a roller. Bricks and Masonary often only require cleaning prior to painting. However old bricks that have been damaged by constant exposure to the elements may have a weakened surface and may require a penetrative primer or sealer as a base coat. Be aware brick mortar can also weaken over time. The number of coats required will depend on the paint, surface and application method used. Follow instructions on the paint can regarding drying times. Rokset Tip! Painting your whole house is a BIG job. To keep motivated it s best to see results. The best way to do this is to prepare and paint one wall or area at a time. This gives you results sooner and keeps you motivated to finish the whole house! Clean up and Care See Brush and Roller Care and Cleaning for full cleaning and product care instructions. For professional advice on your particular task, please speak to a paint specialist.

10 guttering and pipe work Little Gem H/D Cage Frame Little Gem Extension Pole Little Gem Roller Tray Pro Mini Fabric Roller Complete 110mm Pro Pipe Roller 90mm Pro Pipe Roller Replacement 2pk Little Gem Opal Wall Brushes Little Gem GP Sponge Flexisand Sanding Sponge Rokset Wire Brush Little Gem Cover Quick Rokset Canvas or Plastic Drop Sheet Rokset Tack Cloth or Pocket Duster Preparation Galvanized gutters and downspouts must be prepared correctly to prevent rust. Replace damaged gutters and pipe work before paint application. Ensure all gutters and pipe work are securely fastened to the home. Fill any holes or cracks with the appropriate filler and allow to cure as per instructions. If using a silicone sealant ensure it is suitable to paint over. Sand surfaces smooth to remove old paint and sharp edges and to smooth fillers. Use a wire brush followed by a light sanding with a sanding block. (NB: sanding dust from all surface types can be harmful. Use dust masks, gloves and coveralls to protect yourself and your clothing). Thoroughly wash and degrease surfaces using sugar soap. Allow to dry completely before painting. If necessary, use a moss and mould cleaner prior to painting. Tape up adjoining surfaces and around any fixtures or fittings. Rinse rollers and brushes in solvent or water, dependant on the paint type. Allow to dry before use. Immediately before painting use a tack cloth or pocket duster to remove excess dust and fine particles. Application - continued on next page For professional advice on your particular task, please speak to a paint specialist.

11 guttering and pipe work Application Paint drying times vary depending on temperature. Consult your paint professional for advice on ideal painting conditions. Always take the necessary safety precautions when painting. Remember ladder safety and keep the floor clear to avoid accidents. Speak to your paint specialist about applying a base coat, primer or rust resistant application. Priming is especially important on surfaces that have never been painted. Start at the top and work your way down. This allows drips to be painted over. If you are painting the whole house, paint the gutters after the fascia board and under the eaves. Then paint the walls, windows and doors followed by the downpipes. When painting guttering, paint the inside first followed by gutter exterior. Using a brush apply paint from side to side in long smooth strokes and finish coating the area as directed in Painting with Brushes. Use a pipe roller when painting pipe work. A painter s mitt can also be used to apply paint to pipe work and reach tricky spots. Do not use large brushes on pipe work as bristles will divide down the middle making paint application uneven and ruining the brush. Repeat process for each coat. The number of coats required will depend on the paint, surface and application method used. Follow instructions on the paint can regarding drying times. Clean up and Care See Brush and Roller Care and Cleaning for full cleaning and product care instructions. For professional advice on your particular task, please speak to a paint specialist.

12 exterior flooring painting All Rounder Black Foam Cover LIttle Gem H/D Cage Frame LIttle Gem Extension Pole LIttle Gem Roller Tray Little Gem Opal Wall Brushes Little Gem GP Sponge Flexisand Sanding Sponge my project Little Gem Cover Quick Rokset Canvas or Plastic Drop Sheet Rokset Tack Cloth or Pocket Duster Preparation Speak to your concrete/cement professional for the best advice on new concrete, curing treatments, excess moisture tests and different cement preparations. This preparation guide is for existing concrete floors. Fill any holes or cracks with the appropriate filler and allow to cure as per instructions. Thoroughly wash and degrease surfaces using sugar soap. This is best done using a stiff bristle broom. Rinse with clean water and repeat process if grease and dirt remain. Allow to dry completely before painting. If necessary, use a moss and mould cleaner prior to painting. Water blasting will provide an excellent surface for painting. Water blast at 3000 psi and allow surface to dry for at least 24 hours before starting paint application. Tape up adjoining surfaces and around any fixtures or fittings. Rinse rollers and brushes in solvent or water, dependent on the paint type. Allow to dry before use. Application Paint drying times vary depending on temperature. Consult your paint professional for advice on ideal painting conditions. Speak to your paint specialist about applying a base coat, primer or concrete sealant. Priming is especially important on surfaces that have never been painted. The easiest and best way to apply paint to your concrete flooring is with a roller and roller pole. Brushes should be used for corners and edging. Using a brush paint a mm border around the floor surface. This is known as cutting in. When completing your project do not paint over the area that has been cut in by the brush. To start push roller along the floor as directed in Painting with Rollers. Repeat this process for each coat. The number of coats required will depend on the paint, surface and application method used. Follow instructions on the paint can regarding drying times. Check with your paint specialist if a final sealant coat is required. Clean up and Care See Brush and Roller Care and Cleaning for full cleaning and product care instructions. For professional advice on your particular task, please speak to your local paint specialist.

13 corrugated roof or fence Little Gem Opal Wall Brush in sizes 50mm or 63mm Little Gem Roofing Kit Little Gem GP Sponge Flexisand Sanding Sponge Little Gem Cover Quick Rokset Canvas or Plastic Drop Sheet Rokset Tack Cloth or Pocket Duster Preparation Fill any holes or cracks with the appropriate filler and allow to cure as per instructions. Sand surfaces smooth to remove old paint and sharp edges and to smooth fillers. Use a wire brush followed by a light sanding with a sanding block. (NB: sanding dust from all surface types can be harmful. Use dust masks, gloves and coveralls to protect yourself and your clothing). Thoroughly wash and degrease surfaces using sugar soap. Allow to dry completely before painting. If necessary, use a moss and mould cleaner prior to painting. Tape up adjoining surfaces and around any fixtures or fittings. Rinse rollers and brushes in solvent or water, dependent on the paint type. Allow to dry before use. Immediately before painting use a tack cloth or pocket duster to remove excess dust and fine particles. Application Paint drying times vary depending on temperature. Consult your paint professional for advice on ideal painting conditions. Speak to your paint specialist about applying a base coat, primer or rust resistant application. Priming is especially important on surfaces that have never been painted. Using a brush paint a mm border around the fence or roof surface and any fittings. This is known as cutting in. When completing your project do not paint over the area that has been cut in by the brush. Using a corrugated roller apply paint in a straight line following the corrugations of the surface in one direction and then the other. Place the roller on the next set of corrugations and repeat until complete. Be careful not to overlap on corrugations as this may affect the paint finish. Repeat this process for each coat. The number of coats required will depend on the paint, surface and application method used. Follow instructions on the paint can regarding drying times. Clean up and Care See Brush and Roller Care and Cleaning for full cleaning and product care instructions. For professional advice on your particular task, please speak to your local paint specialist.

14 timber decking and fencing my project All Rounder All Finish Kit OR Little Gem Roller Tray Little Gem H/D Cage Frame Pro Decking Roller Little Gem Extension Pole Little Gem Opal Wall Brushes Rokset Polishing and Staining Pad Little Gem GP Sponge Flexisand Sanding Sponge Little Gem Cover Quick Rokset Canvas or Plastic Drop Sheet Rokset Tack Cloth or Pocket Duster Preparation Loose timber boards should be fastened firm. Ensure all nails sit just below the surface. Fill any holes or cracks with the appropriate filler and allow to cure as per instructions. Sand surfaces smooth to remove old paint and sharp edges and to smooth fillers. Always sand along the grain of the timber. (NB: sanding dust from all surface types can be harmful. Use dust masks, gloves and coveralls to protect yourself and your clothing). Thoroughly wash and degrease surfaces using sugar soap. Allow to dry completely before painting. If necessary, use a moss and mould cleaner prior to painting. Tape up adjoining surfaces and around any fixtures or fittings. Lay drop sheets to protect surrounding areas. Rinse rollers and brushes in solvent or water, dependant on the paint type. Allow to dry before use. Immediately before painting use a tack cloth or pocket duster to remove excess dust and fine particles. Application - continued on next page For professional advice on your particular task, please speak to your local paint specialist.

15 timber decking and fencing my project Application Paint drying times vary depending on temperature. Consult your paint professional for advice on ideal painting conditions. Always take the necessary safety precautions when painting. Remember ladder safety and keep the floor clear to avoid accidents. Stain and paint should not be applied to timber that has a high moisture content. Contact your local paint specialist for further information. Speak to your paint specialist about applying a base coat, primer, timber pre-treatment or rust resistant application. Priming is especially important on surfaces that have never been painted. Apply stain or paint to timber using a brush or roller along the length of the grain or grooves of the timber. Wipe off excess timber stain with a clean, lint free cloth and finish coating the area as directed in Painting with Brushes or Rollers. Always apply stain or paint to the end grains (i.e. underneath the fence). This will prevent moisture penetration which can eventually lead to timber cracking and rotting. Repeat this process for each coat. The number of coats required will depend on the paint, surface and application method used. Follow instructions on the paint can regarding drying times. Clean up and Care See Brush and Roller Care and Cleaning for full cleaning and product care instructions. For professional advice on your particular task, please speak to your local paint specialist.

16 staining a timber floor Pro Seamless Foam Cover Little Gem H/D Cage Frame LIttle Gem Extension Pole Little Gem Roller Tray Little Gem Opal Wall Brushes Little Gem GP Sponge Flexisand Sanding Sponge Little Gem Cover Quick Rokset Plastic Drop Sheets Rokset Tack Cloth or Pocket Duster Preparation and Application Preparing and staining wooden floors is a complicated process. Please consult your local flooring and paint specialist for professional advice on the procedures and products that suit your specific needs. For professional advice on your particular task, please speak to your local paint specialist.

17 timber doors, window and trim my project Little Gem Opal Wall Brushes Little Gem Opal Cutter Brushes Little Gem Small Job Kit Little Gem Glossing Kit General Purpose Sponge Flexisand Sanding sponge Painters Tape Rokset Canvas or Plastic Drop Sheet Tack Cloth or Pocket Duster Preparation Fill any holes or cracks with the appropriate filler and allow to cure as per instructions. Sand surfaces smooth to remove old paint and sharp edges and to smooth fillers. Always sand along the grain of the timber. (NB: sanding dust from all surface types can be harmful. Use dust masks, gloves and coveralls to protect yourself and your clothing). Thoroughly wash and degrease surfaces using sugar soap. Allow to dry completely before painting. Tape up adjoining surfaces and around any fixtures and fittings. Lay drop sheets to protect surrounding areas. Rinse rollers and brushes in solvent or water, dependent on the paint type. Allow to dry before use. Immediately before painting use a tack cloth or pocket duster to remove excess dust and fine particles. Application Speak to your paint specialist about applying a base coat, primer or rust resistant application. Priming is especially important on surfaces that have never been painted. For the best brush finish apply paint, varnish or stain from side to side in smooth strokes. Start at the top and work your way down. This allows drips to be painted over. Concentrate on one area at a time. Alternatively use a small roller for paint application. Rollers are quick and easy to use and will not leave brush strokes on the finished surface. Roll paint on by using even strokes. Repeat either process for each coat. The number of coats required will depend on the paint, surface and application method used. Follow instructions on the paint can regarding drying times. Clean up and Care See Brush and Roller Care and Cleaning for full cleaning and product care instructions. For professional advice on your particular task, please speak to your local paint specialist.

18 interior walls and ceiling Little Gem All Paints Roller Kit OR Little Gem Roller Tray Little Gem H/D Cage Frame Little Gem Wall/Ceiling Cover 10mm nap Little Gem Extension Pole Little Gem Opal Wall Brushes Little Gem Opal Cutter Brushes Little Gem GP Sponge Flexisand Sanding Sponge Painters Tape Rokset Canvas or Plastic Drop Sheet Rokset Tack Cloth or Pocket Duster Preparation Fill any holes or cracks with the appropriate filler and allow to cure as per instructions. Sand surfaces smooth to remove old paint and sharp edges and to smooth fillers. (NB: sanding dust from all surface types can be harmful. Use dust masks, gloves and coveralls to protect yourself and your clothing). Thoroughly wash and degrease surfaces using sugar soap. Allow to dry completely before painting. High use areas such as kitchens may require this step to be repeated. Tape up adjoining surfaces and around fixtures and fittings. Rinse rollers and brushes in solvent or water, dependent on the paint type. Allow to dry before use. Immediately before painting use a tack cloth or pocket duster to remove excess dust and fine particles. Application Always take the necessary safety precautions when painting. Remember ladder safety and keep the floor clear to avoid accidents. Speak to your paint specialist about applying a base coat, primer or rust resistant application. Priming is especially important on surfaces that have never been painted. Using a brush paint a mm border around the wall area, this is known as cutting in. Cut in around power points and light switches using a smaller border of about 25-50mm. When completing your project do not paint over the area that has been cut in by the brush. To start push roller and/or extension pole in a diagonal motion along the wall to form an M about a metre wide. Going in the opposite direction form a W to fill the gaps. Keep contact with the surface during this process and apply even pressure for a smooth finish. Next roll in a criss-cross motion to ensure complete coverage. Finish this section rolling lightly in vertical strokes from floor to ceiling as directed in Painting with Rollers. Move to next section and repeat above steps. Repeat this process for each coat. The number of coats required will depend on the paint, surface and application method used. Follow instructions on the paint can regarding drying times. Clean up and Care See Brush and Roller Care and Cleaning for full cleaning and product care instructions. my project For professional advice on your particular task, please speak to your local paint specialist.

19 skirtings and stairs Little Gem Opal Mini Brush Little Gem Opal Cutter Brush Pro Mini Roller Little Gem Mini Roller Tray Little Gem GP Sponge Flexisand Sanding Sponge Little Gem Cover Quick Rokset Canvas or Plastic Drop Sheet Rokset Tack Cloth or Pocket Duster Preparation Fill any holes or cracks with the appropriate filler and allow to cure as per instructions. Sand surfaces smooth to remove old paint and sharp edges and to smooth fillers. Always sand along the grain of the timber. (NB: sanding dust from all surface types can be harmful. Use dust masks, gloves and coveralls to protect yourself and your clothing). Thoroughly wash and degrease surfaces using sugar soap. Allow to dry completely before painting. Tape up adjoining surfaces and around any fixtures and fittings. Lay drop sheets to protect surrounding areas. Rinse rollers and brushes in solvent or water, dependent on the paint type. Allow to dry before use. Immediately before painting use a tack cloth or pocket duster to remove excess dust and fine particles. Application Speak to your paint specialist about applying a base coat, primer or rust resistant application. Priming is especially important on surfaces that have never been painted. For the best brush finish apply paint, varnish or stain from side to side in smooth strokes. Start at the top and work your way down. This allows drips to be painted over. Concentrate on one area at a time. Alternatively, use a small roller for paint application. Rollers are quick and easy to use and will not leave brush strokes on the finished surface. Roll paint on by using even strokes. Paint applied too liberally will run. Repeat either process for each coat. The number of coats required will depend on the paint, surface and application method used. Follow instructions on the paint can regarding drying times. Stairs if you do not need to access your stairs immediately after painting then start from the top and work your way down. A good tip if you need to keep accessing the stairs is to paint every second stair. Allow paint to dry and then paint remaining stairs. Clean up and Care See Brush and Roller Care and Cleaning for full cleaning and product care instructions. For professional advice on your particular task, please speak to your local paint specialist.

20 painting cupboards and drawers Little Gem Opal Wall Brush Little Gem Opal Cutter Brush Little Gem 110mm Mini Foam Kit Pro 110mm Foam 2pk Covers Little Gem Mini Roller Tray Little Gem GP Sponge Flexisand Sanding Sponge Little Gem Cover Quick Rokset Canvas or Plastic Drop Sheet Rokset Tack Cloth or Pocket Duster Preparation Remove drawer fronts and cupboard doors. Remove all hardware from the doors and drawers. Fill any holes or cracks with the appropriate filler and allow to cure as per instructions. Sand surfaces smooth to remove old paint and sharp edges and to smooth fillers. Always sand along the grain of the timber. (NB: sanding dust from all surface types can be harmful. Use dust masks, gloves and coveralls to protect yourself and your clothing). Thoroughly wash and degrease surfaces using sugar soap. Allow to dry completely before painting. Rinse rollers and brushes in solvent or water, dependent on the paint type. Allow to dry before use. Immediately before painting use a tack cloth or pocket duster to remove excess dust and fine particles. Application Speak to your paint specialist about applying a base coat, primer or rust resistant application. Priming is especially important on surfaces that have never been painted. For the best brush finish apply paint, varnish or stain from side to side in smooth strokes. Start at the top and work your way down. This allows drips to be painted over. Concentrate on one area at a time. Finish strokes off by gently going over with a mini roller. This will remove any ridges that may form. Paint applied too liberally will run. Repeat this process for each coat. The number of coats required will depend on the paint, surface and application method used. Follow instructions on the paint can regarding drying times. If desired varnish can be applied as a final coat for a clear finish. Clean up and Care See Brush and Roller Care and Cleaning for full cleaning and product care instructions. For professional advice on your particular task, please speak to your local paint specialist.

21 painting furniture Little Gem Opal Wall Brushes Little Gem Opal Cutter Brushes Little Gem Staining and Polishing Pad Little Gem 110mm Mini Foam Kit Pro Mini 110mm Spare Foam 2pk Little Gem Mini Roller Tray Little Gem GP Sponge Flexisand Sanding Sponge Little Gem Cover Quick Rokset Canvas or Plastic Drop Sheet Rokset Tack Cloth or Pocket Duster Preparation Remove all hardware from furniture. Fill any holes or cracks with the appropriate filler and allow to cure as per instructions. Sand surfaces smooth to remove old paint and sharp edges and to smooth fillers. Always sand along the grain of the timber. (NB: sanding dust from all surface types can be harmful. Use dust masks, gloves and coveralls to protect yourself and your clothing). Thoroughly wash and degrease surfaces using sugar soap. Allow to dry completely before painting. Rinse rollers and brushes in solvent or water, dependent on the paint type. Allow to dry before use. Immediately before painting use a tack cloth or pocket duster to remove excess dust and fine particles. Application Speak to your paint specialist about applying a base coat, primer or rust resistant application. Priming is especially important on surfaces that have never been painted. For the best brush finish apply paint, varnish or stain from side to side in smooth strokes. Start at the top and work your way down. This allows drips to be painted over. Concentrate on one area at a time. Alternatively, use a small roller for paint application. Rollers are quick and easy to use and will not leave brush strokes on the finished surface. Roll paint on by using even strokes. Paint applied too liberally will run. Repeat either process for each coat. The number of coats required will depend on the paint, surface and application method used. Follow instructions on the paint can regarding drying times. If desired varnish can be applied as a final coat for a clear finish. Allow furniture plenty of time to dry. Do not place anything on furniture for at least one week as it may easily mark. Replace hardware after this time. Clean up and Care See Brush and Roller Care and Cleaning for full cleaning and product care instructions. For professional advice on your particular task, please speak to your local paint specialist.