Creepy Lab. Instructions. Back Wall. YOU WILL NEED: Pegboards: 6 Large squares

Transcription

1 Instructions Back Wall YOU WILL NEED: Pegboards: 6 Large squares Other: Scissors, clear tape 1. Some of the patterns require multiple pegboards to be assembled together as shown below or otherwise as shown throughout the project sheet. Cut these patterns out and tape together in the same way as the pegboards are assembled. If you are using clear pegboards, slide the actual-size patterns underneath them. Place your beads on the pegboards as shown. 2. Ask an adult to fuse your designs see page 4 for further instructions Hot Coral - 32 Raspberry - 15 Cranapple - 5 Orange - 69 Cheddar - 39 Creme Yellow - 66 Prickly Pear - 26 Kiwi Lime - 16 Light Green - 24 Parrot Green Dark Green Pearl Light Blue - 30 Toothpaste - 26 Turquoise - 13 Dark Blue - 87 Blueberry Cream - 34 Periwinkle Blue Plum - 14 Purple - 48 Rust - 6 Brown Pearl Silver * Dark * Black* White - 6 Raspberry Pearl Stripe - 20 Fire Stripe - 36 Gold Pearl Stripe - 40 Prickly Pear Pearl Stripe - 50 Cucumber Stripe Starry Nite Stripe Royal Blue Pearl Stripe - 37 Grape Stripe - 32 Monkey Stripe Silver Pearl Stripe - 35 Zebra Stripe - 49 * You will need 2 bags of these colors Find these pattern sections on pages

2 Back Wall Section 1 Section 2 2

3 Back Wall Section 3 Section 4 3

4 Back Wall Section 5 Fusing Instructions Only Adults Iron 1. Place your pegboard on a flat, heat-safe surface. 2. Set a household iron to the medium setting. Place ironing paper over the pegboard. In a circular motion, begin to iron the project. Do not press down with the iron. As the beads begin to fuse, you will see circles of the beads start to show through the paper. When ironed properly, the beads will still have an open center. Let the design cool. 3. Remove the paper and bead design from the peg board. Flip the design over to expose the non-fused side. Repeat step two. Let cool completely. NOTE: Beads need heat for about seconds per side to fuse evenly. Lift the paper occasionally to see how the beads are fusing. Depending on the size of the project, additional heating time may be required. DO NOT OVER-IRON the beads as it will make the centers of the beads close and can make the assembly you do with your project more challenging. 4

5 Back Wall Section 6 Castle Turret A Front / D Back Pearl Silver Dark Starry Nite Stripe A Front D Back 5

6 Castle Turret B Left / C Right Pearl Silver Dark Starry Nite Stripe Back B Left Front Front C Right Back D Back Castle Turret Base 1 Periwinkle Blue Pearl Silver B Left Base 1 C Right A Front 6

7 Castle Turret Base 2 D Back Base 2 Periwinkle Blue Pearl Silver Black B Left C Right A Front Power Generator Pearl Light Blue Dark Blue Black Gold Pearl Stripe Prickly Pear Pearl Stripe Silver Pearl Stripe 7

8 Assemble two pegboards vertically to work all four sides of the tower here and on page 9. Cut out and assemble the patterns the same way. Front C Right Back A Front Castle Tower C Right, A Front Orange Yellow Parrot Green Dark Green Brown Pearl Silver Dark Black Cucumber Stripe Starry Nite Stripe Monkey Stripe Zebra Stripe 8

9 D Back Back B Left Front Castle Tower D Back, B Left Yellow Parrot Green Dark Green Brown Pearl Silver Dark Black Cucumber Stripe Starry Nite Stripe Monkey Stripe 9

10 Cross Wall This wall section crosses the back wall so that the pumpkin is outside the castle and the laboratory is inside the castle. Assemble two pegboards side by side as shown at left. Cut out and assemble the patterns the same way. Outside Hot Coral Orange Creme Prickly Pear Parrot Green Dark Green Dark Black Cucumber Stripe 10

11 Cross Wall Inside Plum Raspberry Hot Coral Orange Creme Yellow Prickly Pear Kiwi Lime Light Green Pearl Light Blue Turquoise Blueberry Cream Periwinkle Blue Purple Pearl Silver Dark Black White Raspberry Pearl Stripe Royal Blue Pearl Stripe Grape Stripe Zebra Stripe 11

12 Torches Make three of each piece. Orange Cheddar Yellow Prickly Pear Brown Black Fire Stripe Monkey Stripe MAKE 3 Lab Table Assemble two pegboards side by side as shown above. Cut out and assemble the patterns the same way. Hot Coral Cranapple Kiwi Lime Light Green Brown Monkey Stripe 12

13 ASSEMBLY 1 Back Wall / Tower Insert the notched ends of the back wall through the slots of the tower piece C. Make sure the walls are perpendicular and touch. C B A C D 2 Back Wall / Tower Connect the tower pieces A, B, and D with tower piece C to complete the tower. C 13

14 ASSEMBLY B Base 2 D C Tower Insert the tower Base 1 over the tabs of the assembled tower walls, pushing down completely until 2 rows of beads come through the slots. B A D A C Base 1 Insert tower Base 2 over the tabs in the same way until 1 row of beads comes through the slots. This will help support the tower. 3 D 4 Insert the tabs of turret piece D through the slots along the back of the tower. A 6 D 5 B C Insert the tabs of turrets B and C through the slots as with piece D, connecting the sides with piece D. Insert the Power Generator pieces in the slots of Tower Base 2. Insert turret A to complete the tower. 14

15 ASSEMBLY 7 Torches and Lab Table Create the Torches by inserting the double candelabras into the slots of the single ones. Insert the tabs of the legs into the bottom of the Table. 9 Final Assembly Insert the tabs of the Lab Table into the slots of the Back Wall. Add two of the Torches in the same way above the table. The third Torch is placed through the opening in the Tower. 8 Slide the Crossing Wall through the slot of the Back Wall to complete your. Perler Beads and EKSuccess Brands are either registered trademarks or trademarks of Dimensions Crafts LLC and EK Success Ltd. respectively in the United States and/or other countries Dimensions Crafts LLC. All rights reserved. 15