Features. Applications
|
|
- Blanche Hood
- 5 years ago
- Views:
Transcription
1 HFBR-8 Series HFBR-8 Transmitter HFBR-8 Receiver Megabaud Versatile Link Fiber Optic Transmitter and Receiver for mm POF and µm HCS Data Sheet Description The HFBR-8 Series consists of a fiber-optic transmitter and receiver operating at a 6 nm wavelength (red). The HFBR-8 transmitter is an LED in a low cost plastic housing designed to efficiently couple power into µm diameter HCS and mm diameter POF. The HFBR-8 receiver incorporates a PIN detector and digital output IC compatible with CMOS and TTL logic families. HFBR-8 links operate from DC to MBd at distances up to meters with mm POF and up to meters with µm HCS. No minimum link distances are required when using recommended circuits, simplifying design. Versatile Link components can be interlocked (Nplexed together) to minimize space and to provide dual connections with the duplex connectors. Up to eight packages can be interlocked and inserted into a printed circuit board. POF and HCS are available in pre-connectored lengths or can be easily field-terminated. A single transmitter drive current for POF and HCS allows both fibers to be used with a single design. Features Data transmission at signal rates of dc to MBd Up to meters distances with mm Plastic Optical Fiber (POF) Up to meters distances with µm Hard Clad Silica (HCS ) Wide dynamic range receiver allows operation from zero to maximum link distance with a single transmitter drive current Link distances specified for variations in temperature, power supply, and fiber attenuation DC coupled receiver with CMOS/TTL output for easy designs: no data encoding or digitizing circuitry required Pulse width distortion controlled to limit distortion from low duty cycle or burst mode data High noise immunity Compatible with Avago s Versatile Link family of connectors, for easy termination of fiber Applications Industrial control and factory automation Serial field buses Intra-system links; Board-to-Board, Rack-to-Rack Extension of RS-, RS-8 Elimination of ground loops High voltage isolation Reduces voltage transient susceptibility HCS is a registered trademark of SpecTran Corporation. CAUTION:. It is advised that normal static precautions be taken in handling and assembly of these components to prevent damage and/or degradation which may be induced by ESD.
2 HFBR-8 Series MBd Data Link Typical Link Performance, T A = + C Parameter Symbol Typ. [] Unit Condition Note Signaling Rate f S Mb/s NRZ Link Distance with Extra Low Loss POF Cable m MBd,, Link Distance with µm HCS Cable 9 m MBd,, Specified Link Performance, T A = - to +8 C, DC to MBd, unless otherwise noted. Parameter Symbol Min. Max. Unit Condition Note Signaling Rate f S DC Mb/s NRZ Link Distance with Extra Low. m + C,, Loss POF Cable. to +7 C. - to +8 C Link Distance with µm. m + C,, HCS Cable. to +7 C. - to +8 C Pulse Width Distortion PWD - + ns 7% Duty Cycle - + ns Arbitrary Duty Cycle Absolute Maximum Ratings Parameter Symbol Min. Max. Unit Note Storage and Operating Temperature T S,O - +8 C Receiver Supply Voltage V CC V Receiver Average Output Current I O,AVG ma Receiver Output Power Dissipation P OD 8 mw Transmitter Peak Forward Input Current I F,PK 9 ma 6 Transmitter Average Forward Input Current I F,AVG 6 ma Transmitter Reverse Input Voltage V R V Lead Soldering Cycle Temp T SOL +6 C 7 Time sec 7 Recommended Operating Conditions Parameter Symbol Min. Max. Unit Condition Note Ambient Temperature T A - +8 C Power Supply Voltage V CC.7. V < mv p-p Noise Transmitter Peak Forward Current I F,PK 9 ma 6 Transmitter Average Forward Current I F,AV 6 ma Fanout (7 Series TTL) N Notes:. Typical data at + C, V CC = V.. With recommended transmitter and receiver application circuits (6 ma nominal drive current).. POF is HFBR-R/EXXYYY plastic ( mm) optical fiber. Worst case attenuation used (. db/m from - C to +8 C at 66 nm).. HCS is HFBR-H/VXXYYY hard clad silica (/ µm) fiber. Worst case attenuation is used ( db/km from C to +7 C and db/km from - C to +8 C at 6 nm).. BER -9, - PRBS NRZ MBd. 6. For I F,PK > 6 ma, the duty factor must maintain I F,AV 6 ma and pulse with µs mm below seating plane.
3 HFBR-8 Transmitter The HFBR-8 transmitter incorporates a 6 nm LED in a light gray, nonconductive plastic housing. The high light output power enables the use of both plastic optical fiber (POF) and Hard Clad Silica (HCS) fiber. This transmitter can be operated up to MBd using a simple driver circuit. The HFBR-8 is compatible with all Versatile Link connectors. ANODE CATHODE GROUND GROUND SEE NOTE HFBR-8 Transmitter, Top View 8 GROUND GROUND Electrical and Optical Characteristics: T A = - to +8 C unless otherwise noted. Parameter Symbol Min. Typ. [] Max. Units T A ( C) Conditions Note Peak Output Power P T dbm + I F, dc = 6 ma, mm POF, 6 ma to +7 Fig to +8 Peak Output Power P T dbm + I F,dc = ma, mm POF, ma to +7 Fig to +8 Peak Output Power P T dbm + I F,dc = 6 ma, µm HCS, 6 ma to +7 Fig to +8 Optical Power Tem- P T / T -. %/ C perature Coefficient -. db/ C Peak Emission λ P nm to +7 Wavelength to +8 Peak Wavelength λ/ T. nm/ C Temperature Coefficient Spectral Width FWHM nm Fig. Forward Voltage V F.8..6 V I F,dc = 6 ma Fig. Forward Voltage Tem- V F / T -.8 mv/ C Fig. perature Coefficient Reverse Input Break- V BR. V I F,dc = - µa down Voltage Diode Capacitance C O 6 pf V F = V, f = MHz Transmitter NA. Numerical Aperture Thermal Resistance, θ jc C/W Junction to Case Ω Optical Rise Time t r ns % to 9%, I F = 6 ma Ω Optical Fall Time t f ns Notes:. Typical data are at C.. Optical power measured at the end of. meters of mm diameter plastic or µm diameter hard clad silica fiber with a large area detector.. Minimum and maximum values for P T over temperature are based on a fixed drive current. The recommended drive circuit has temperature compensation which reduces the variation in P T over temperature; refer to Figures and 6.. Typical value measured from junction to PC board solder joint for horizontal mount package, HFBR-8.. Pins and 8 are for mounting and retaining purposes, but are electrically connected; pins and are electrically isolated. It is recommended that pins,, and 8 all be connected to ground to reduce coupling of electrical noise. 6. Refer to the Plastic Optical Fiber and HCS Fiber Cable and Connectors for Versatile Link Technical Data Sheet for cable connector options for mm plastic and µm HCS optical fiber. Fig.
4 V F FORWARD VOLTAGE V. - C. C C. 7 C C. I F,DC TRANSMITTER DRIVE CURRENT ma P T NORMALIZED OUTPUT POWER db - C C - 8 C I F,DC TRANSMITTER DRIVE CURRENT ma Figure. Typical Forward Voltage vs. Drive Current. Figure. Typical Normalized Optical Power vs. Drive Current. NORMALIZED SPECTRAL OUTPUT POWER C C C 7 C 8 C NORMALIZED OUTPUT POWER V CC =. V V CC =. V V CC =.7 V WAVELENGTH (nm) TEMPERATURE C Figure. Typical Normalized Optical Spectra. Figure. Typical Normalized Optical Power vs. Temperature (in Recommended Drive Circuit). PWD ns V CC =. V V CC =. V V CC =.7 V V CC DATA 7 C R R 6 8 / SN7 C HFBR-8 VALUE R KΩ 8 TOLERANCE % TEMPERATURE C R C C 7 Ω. µf. µf % % % Figure. Typical Optical Pulse Width Distortion vs. Temperature and Power Supply Voltage (in Recommended Drive Circuit). Figure 6. Recommended Transmitter Drive Circuit (I F,on = 6 ma Nominal at T A = C). WARNING: WHEN VIEWED UNDER SOME CONDITIONS, THE OPTICAL PORT MAY EXPOSE THE EYE BEYOND THE MAXIMUM PERMISSIBLE EXPO- SURE RECOMMENDED IN ANSI Z6., 99. UNDER MOST VIEWING CONDITIONS THERE IS NO EYE HAZARD.
5 HFBR-8 Receiver The HFBR-8 receiver consists of a silicon PIN photodiode and digitizing IC to produce a logic compatible output. The IC includes a unique circuit to correct the pulse width distortion of the first bit after a long idle period. This enables operation from DC to MBd with low PWD for arbitrary data patterns. The receiver output is a push-pull stage compatible with TTL and CMOS logic. The receiver housing is a dark, conductive plastic, compatible with all Versatile Link connectors. GROUND IC GROUND 8 SEE NOTES,7 HFBR-8 Receiver, Top View NO CONNECT V CC GROUND V O Electrical and Optical Characteristics: T A = - to +8 C,.7 V < V <. V, unless otherwise noted. CC Parameter Symbol Min. Typ.[] Max. Unit T A ( C) Condition Note Fig. Peak POF Sensitivity: P RL,min dbm + mm POF,,6, Minimum Input for -. to +7 PWD < ns Logic to +8 Peak POF Overdrive P RL,max dbm + mm POF,,,,, Limit:Maximum +. to +7 PWD < ns 6 Input for Logic -. - to +8 Peak POF Off State P RH,max - dbm mm POF,6, Limit: Maximum 8 Input for Logic Peak HCS P RL,min dbm + µm HCS,,6 Sensitivity: Minimum -. to +7 PWD < ns Input for Logic -. - to +8 Peak HCS Overdrive P RL,max dbm + µm HCS,,, Limit: Maximum -. to +7 PWD < ns 6 Input for Logic -. - to +8 Peak HCS Off State P RH,max - dbm µm HCS,6, Limit: Maximum 8 Input for Logic Supply Current I CC 7 ma V O = Open High Level Output V OH..7 V Voltage I O = - µa Low Level Output V OL.. V Voltage I O = +.6 ma Output Rise Time t r ns C L = pf 6 Output Fall Time t f ns C L = pf 6 Thermal Resistance, θ jc C/W Junction to Case Electric Field E MAX 8 V/m Near Field, Immunity Electrical Field Source Power Supply PSNI.. V pp Sine Wave 6 Noise Immunity DC - MHz Notes:. Typical data are at + C, V CC =. V.. Input power levels are for peak (not average) optical input levels. For % duty cycle data, peak optical power is twice the average optical power.. Receiver overdrive (P RL,max ) is specified as the limit where PWD will not exceed ns. The receiver will be in the correct state (logic ) for optical powers above P RL,max. However, it may not meet a % symbol period PWD if the overdrive limit is exceeded. Refer to Figure for PWD performance at high received optical powers.. Typical value measured from junction to PC board solder joint for horizontal mount package, HFBR-8.. Pins and 8 are electrically connected to the conductive housing and are also used for mounting and retaining purposes. It is required that pins and 8 be connected to ground to maintain conductive housing shield effectiveness. 6. In recommended receiver circuit, with an optical signal from the recommended transmitter circuit. 7. Pin is electrically isolated internally. Pin may be externally connected to pin for board layout compatibility with HFBR-X, HFBR-X and HFBR-X. Otherwise it is recommended pin be grounded as in Figure. 8. BER E-9, includes a.8 db margin below the receiver switching threshold level (signal to noise ratio = ).
6 6 V CC =. V RECEIVED POWER dbm V CC =.7 V V CC =. V RECEIVED PWD ns TEMPERATURE C P RL RECEIVER OPTICAL INPUT POWER dbm Figure. Typical POF Receiver Overdrive, P RL,max, at MBd, vs. Temperature and Power Supply Voltage. Figure. Typical POF Receiver Pulse Width Distortion vs. Optical Power at MBd PWD ns PWD ns V CC VOLTS V CC VOLTS Figure. Typical POF Receiver Pulse Width Distortion vs. Power Supply Voltage at High Optical Power ( dbm,pk, MBd). Figure. Typical POF Receiver Pulse Width Distortion vs. Power Supply Voltage at Low Optical Power, (- dbm,pk, MBd). HFBR-8 IC 8 C R V CC DATA R C VALUE.7 Ω. µf TOLERANCE % % Figure. Recommended Receiver Application Circuit. 6
7 8 GROUND V CC PIN PHOTODIODE AMPLIFIER REFERENCE VOLTAGE THRESHOLD GENERATOR FIRST BIT BURST PWD CORRECTION COM- PARATOR V O, DATA GROUND GROUND Figure 6. HFBR-8 Receiver Block Diagram. Versatile Link Mechanical Dimensions Versatile Link Printed Circuit Board Layout Dimensions PIN NO. INDICATOR. (.8).6 (.) 8.9 (.7) 6. (.) 7.6 (.). (.). (.). (.6). (.) 7.6 (.) 8. (.) DIA. 7.6 (.) 7.6 (.).8(.) MAX..6 (.) MIN.. (.).7 (.). (.) TOP VIEW.8 (.7) MIN..6 (.) DIA.. (.8).7 (.68) NOTE: ALL DIMENSIONS IN MM (INCHES). ALL DIMENSIONS ±. mm UNLESS OTHERWISE SPECIFIED. 8 ELECTRICAL PIN FUNCTIONS PIN NO. TRANSMITTER HFBR-8 ANODE CATHODE GROUND* GROUND* GROUND** GROUND** RECEIVER HFBR-8 SIGNAL, V O GROUND V CC (+ V) GROUND* GROUND** GROUND** * NO INTERNAL CONNECTION, GROUND CONNECTION RECOMMENDED. ** PINS AND 8 CONNECTED INTERNALLY TO EACH OTHER.
8 For product information and a complete list of distributors, please go to our website: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies Limited in the United States and other countries. Data subject to change. Copyright 7 Avago Technologies Limited. All rights reserved. Obsoletes EN AV-99EN - December 7, 7 8
12 Megabaud Versatile Link Fiber Optic Transmitter and Receiver for 1 mm POF and 200 μm HCS. Features. Applications
HFBR-EZ Transmitter HFBR-EZ Receiver Megabaud Versatile Link Fiber Optic Transmitter and Receiver for mm POF and μm HCS Data Sheet Description The HFBR-EZ transmitter is an LED in a low cost plastic housing
More informationData Sheet. HFBR-1506AMZ/HFBR-2506AMZ Fiber Optic SMA Transmitters and Receivers for 16 MBd SERCOS Applications. Description. Features.
HFBR-0AMZ/HFBR-20AMZ Fiber Optic SMA Transmitters and Receivers for MBd SERCOS Applications Data Sheet Description SERCOS, an acronym for SErial Realtime COmmunications Systems, is a standard digital interface
More informationData Sheet HFBR-1506AFZ/HFBR-2506AFZ. Full Metal Fiber Optic SMA Transmitters and Receivers for 16 MBd SERCOS Applications. Description.
HFBR-0AFZ/HFBR-20AFZ Full Metal Fiber Optic SMA Transmitters and Receivers for MBd SERCOS Applications Data Sheet Description SERCOS, an acronym for SErial Realtime COmmunications Systems, is a standard
More informationDistributed by: www.jameco.com -800-83-22 The content and copyrights of the attached material are the property of its owner. 25 Megabaud Versatile Link The Versatile Fiber Optic Connection Technical Data
More informationFiber Optic Transmitters and Receivers for SERCOS, PROFIBUS and INTERBUS-S Applications. Technical Data
Fiber Optic Transmitters and Receivers for SERCOS, PROFIBUS and INTERBUS-S Applications Technical Data HFBR-0A/20A (SMA Tx/Rx for SERCOS) HFBR-B/2B (ST Tx/Rx for PROFIBUS) HFBR-0C/20C (SMA Tx/Rx for INTERBUS-S)
More informationThe HFBR-1604 is a selected version of the HFBR-1602, with power specified to meet the
SERCOS Fiber Optic Transmitters and Receiver Technical Data HFBR-0600 Series Features Fully Compliant to SERCOS Optical Specifications Optimized for 1 mm Plastic Optical Fiber Compatible with SMA Connectors
More informationAFBR-1555ARZ, AFBR-2555ARZ (SMA Tx/Rx for SERCOS)
Reinforced Metal Fiber Optic Transmitter and Receiver for SERCOS Applications Description SERCOS The Serial Realtime Communications System (SERCOS) is a standard digital interface for communication in
More informationHFBR-1505AFZ/2505AFZ (SMA Tx/Rx for SERCOS) HFBR-1515BFZ/2515BFZ (ST Tx/Rx for PROFIBUS) HFBR-1505CFZ/2505CFZ (SMA Tx/Rx for INTERBUS-S)
HFBR-0AFZ/20AFZ (SMA Tx/Rx for SERCOS) HFBR-BFZ/2BFZ (ST Tx/Rx for PROFIBUS) HFBR-0CFZ/20CFZ (SMA Tx/Rx for INTERBUS-S) Full Metal Fiber Optic Transmitters and Receivers for SERCOS, PROFIBUS and INTERBUS-S
More informationHFBR-1505AZ/2505AZ (SMA
HFBR-0AZ/20AZ (SMA Tx/Rx for SERCOS) HFBR-BZ/2BZ (ST Tx/Rx for PROFIBUS) HFBR-0CZ/20CZ (SMA Tx/Rx for INTERBUS-S) Fiber Optic Transmitters and Receivers for SERCOS, PROFIBUS and INTERBUS-S Applications
More informationData Sheet AFBR-2418MZ. DC-50MBd Miniature Link Fiber Optic Receiver. Description. Features. Applications. AFBR-24x8xZ Available Part Numbers
AFBR-2xxZ DC-0MBd Miniature Link Fiber Optic Receiver Data Sheet Description The component is designed to provide cost effective, high performance fiber optic communication links for information systems
More informationDC-10 MBd RedLink Transmitter and Receiver Pair
DC-0 MBd RedLink Transmitter and Receiver Pair DATA SHEET 650 nm DC-0 MBd RedLink Fiber Optic Transmitter and Receiver FEATURES Ideal for use with POF and PCS fiber Optimized for data transmission from
More informationDC-5 MBd RedLink Transmitter and Receiver Pair
DC-5 MBd RedLink Transmitter and Receiver Pair DATA SHEET 650 nm DC-5 MBd RedLink Fiber Optic Transmitter and Receiver FEATURES Ideal for use with POF Optimized for data transmission from DC to 5 MBd Industrial
More informationIsolation in Test and Measurement Instruments Error Free Signalling for Industrial and Manufacturing
Versatile Link The Versatile Fiber Optic Connection Technical Data HFBR-0501 Series Features Low Cost Fiber Optic Components Enhanced Digital Links dc-5 MBd Extended Distance Links up to 120 m at 40 kbd
More informationAFBR-1528CZ and AFBR-2528CZ
DC to 10-MBd Versatile Link Fiber Optic Analog Transmitter and Digital Receiver for 1-mm POF and 200-μm PCS Description The AFBR-1528CZ analog transmitter utilizes a 650-nm LED source, and the AFBR-2528CZ
More informationData Sheet AFBR-2419MZ. 50 MBd Miniature Link Fiber Optic Receiver. Description. Features. Applications. AFBR-24x9xZ Available Part Numbers
AFBR-2x9xZ 0 MBd Miniature Link Fiber Optic Receiver Data Sheet Description The AFBR-2x9Z series components provide cost effective, high performance fiber optic communication links for information systems
More informationData Sheet. AFBR-S10TR001Z Compact 650 nm Analog Transceiver with Compact Versatile-Link Connector for Sensing Over POF. Description.
AFBR-STRZ Compact 65 nm Analog Transceiver with Compact Versatile-Link Connector for Sensing Over POF Data Sheet Description Avago Technologies' AFBR-STRZ transceiver provides system designers with the
More informationData Sheet. Description. Features. Transmitter. Applications. Receiver. Package
AFBR-59F1Z 125MBd Compact 650 nm Transceiver for Data Communication over Polymer Optical Fiber (POF) cables with a bare fiber locking system Data Sheet Description The Avago Technologies AFBR-59F1Z transceiver
More informationFT10MHNR FT10MVNR. 650 nm DC 10 MBd RedLink Fiber Optic Transmitter Data Sheet DESCRIPTION FEATURES APPLICATIONS AVAILABLE OPTIONS
FT10MHNR FT10MVNR 650 nm DC 10 MBd RedLink Fiber Optic Transmitter Data Sheet DESCRIPTION The Firecomms DC to 10 MBd RedLink transmitter is based on the highly reliable Firecomms designed Resonant Cavity
More informationFM10DHIR FM10DHNR FM10DVIR FM10DVNR DC 10 RedLink Fiber Optic Receiver Preliminary Data Sheet
NOT RECOMMENDED FOR NEW DESIGNS * For new designs please see part numbers: FR10DHIR FR10DHNR FR10DVIR FR10DVNR FM10DHIR FM10DHNR FM10DVIR FM10DVNR DC 10 RedLink Fiber Optic Receiver Preliminary Data Sheet
More informationData Sheet. HFBR-0500Z Series Versatile Link The Versatile Fiber Optic Connection. Description. Features. Applications
HFBR-0500Z Series Versatile Link The Versatile Fiber Optic Connection Data Sheet Description The Versatile Link series is a complete family of fiber optic link components for applications requiring a low
More informationFR50MxxR. DC-50 RedLink Fiber Optic Receiver Datasheet DESCRIPTION FEATURES AVAILABLE OPTIONS APPLICATIONS
FR50MxxR DC-50 RedLink Fiber Optic Receiver Datasheet DESCRIPTION The Firecomms DC-50 MBd RedLink receiver is a fully integrated photodiode and receiver IC. The receiver is housed in a miniature package
More informationFR50MxxR DC-50 RedLink Fiber Optic Receiver Datasheet
FR50MxxR DC-50 RedLink Fiber Optic Receiver Datasheet DESCRIPTION The Firecomms DC-50 MBd RedLink receiver is a fully integrated photodiode and receiver IC. The receiver is housed in a miniature package
More informationFT01MHNG FT01MVNG. 530 nm DC-1 MBd RedLink Fiber Optic Transmitter Datasheet DESCRIPTION FEATURES APPLICATIONS AVAILABLE OPTIONS
FT01MHNG FT01MVNG 530 nm DC-1 MBd RedLink Fiber Optic Transmitter Datasheet DESCRIPTION The Firecomms DC to 1 MBd green 530 nm transmitter is designed for maximum distance at low speed communication in
More informationFR10DxxR. DC-10 RedLink Fiber Optic Receiver Datasheet DESCRIPTION FEATURES AVAILABLE OPTIONS APPLICATIONS
FR10DxxR DC-10 RedLink Fiber Optic Receiver Datasheet DESCRIPTION The Firecomms DC-10 MBd RedLink receiver is a fully integrated photodiode and receiver IC. The receiver is housed in a miniature package
More informationFR10DxxR. DC-10 RedLink Fiber Optic Receiver Datasheet DESCRIPTION FEATURES AVAILABLE OPTIONS APPLICATIONS
FR10DxxR DC-10 RedLink Fiber Optic Receiver Datasheet DESCRIPTION The Firecomms DC-10 MBd RedLink receiver is a fully integrated photodiode and receiver IC. The receiver is housed in a miniature package
More informationFT05MHNR FT05MVNR. 650 nm DC 5 MBd RedLink Fiber Optic Transmitter Data Sheet DESCRIPTION FEATURES APPLICATIONS AVAILABLE OPTIONS
FT05MHNR FT05MVNR 650 nm DC 5 MBd RedLink Fiber Optic Transmitter Data Sheet DESCRIPTION The Firecomms DC to 5 MBd RedLink transmitter is based on the highly reliable Firecomms designed Resonant Cavity
More informationData Sheet. HFBR-0500ETZ Series Versatile Link The Versatile Fiber Optic Connection. Description. Features. Applications
HFBR-0500ETZ Series Versatile Link The Versatile Fiber Optic Connection Data Sheet Description The Versatile Link series is a complete family of fiber optic link components for applications requiring a
More informationFT10MHLR FT10MVLR. 650 nm DC-10 MBd RedLink Fiber Optic Transmitter Datasheet DESCRIPTION FEATURES APPLICATIONS AVAILABLE OPTIONS
FT10MHLR FT10MVLR 650 nm DC-10 MBd RedLink Fiber Optic Transmitter Datasheet DESCRIPTION The Firecomms DC to 10 MBd low current RedLink transmitter is a highly reliable Resonant Cavity Light Emitting Diode
More informationAFBR-59F2Z Data Sheet Description Features Applications Transmitter Receiver Package
AFBR-59F2Z 2MBd Compact 6nm Transceiver for Data communication over Polymer Optical Fiber (POF) cables with a bare fiber locking system Data Sheet Description The Avago Technologies AFBR-59F2Z transceiver
More informationFR05DHIR FR05DVIR. DC-5 MBd Dual Supply Voltage RedLink Receiver Datasheet DESCRIPTION FEATURES APPLICATIONS AVAILABLE OPTIONS
FR05DHIR FR05DVIR DC-5 MBd Dual Supply Voltage RedLink Receiver Datasheet DESCRIPTION The Firecomms DC to 5 MBd Dual supply voltage RedLink receiver is based on a fully integrated photo-diode with TIA
More informationFT05MxNR. 650 nm DC-5 MBd RedLink Fiber Optic Transmitter Datasheet DESCRIPTION FEATURES APPLICATIONS AVAILABLE OPTIONS
FT05MxNR 650 nm DC-5 MBd RedLink Fiber Optic Transmitter Datasheet DESCRIPTION The Firecomms DC to 5 MBd RedLink transmitter is based on the highly reliable Firecomms designed Resonant Cavity Light Emitting
More informationFIBER105.TIF OUTLINE DIMENSIONS in inches (mm) .176 (4.47).165 (4.19) .500 MIN (12.7) FIBER203.DIM. Pinout 1. Capacitor 2. VÙÙ 3.
FEATURES Converts fiber optic input signals to TTL digital outputs Typical sensitivity 500 nw peak ( 33 dbm) Single 5 V supply requirement Edge detection circuitry gives 20 db minimum dynamic range, low
More informationFR05DxIR. DC-5 MBd Dual Supply Voltage RedLink Receiver Datasheet DESCRIPTION FEATURES APPLICATIONS AVAILABLE OPTIONS
FR05DxIR DC-5 MBd Dual Supply Voltage RedLink Receiver Datasheet DESCRIPTION The Firecomms DC to 5 MBd Dual supply voltage RedLink receiver is based on a fully integrated photo-diode with TIA and limiting
More informationData Sheet. AFBR-16xxZ and AFBR-26x4Z/25x9Z DC-50MBd Versatile Link Fiber Optic Transmitter and Receiver for 1 mm POF and 200 µm PCS.
AFBR-16xxZ and AFBR-26x4Z/25x9Z DC-50MBd Versatile Link Fiber Optic Transmitter and Receiver for 1 mm POF and 200 µm PCS Data Sheet Description The AFBR-16xxZ transmitter utilizes a 650 nm LED source with
More informationFR05DHCR FR05DVCR. DC-5 MBd Open Collector Dual Supply Voltage RedLink Receiver Datasheet DESCRIPTION FEATURES APPLICATIONS AVAILABLE OPTIONS
FR05DHCR FR05DVCR DC-5 MBd Open Collector Dual Supply Voltage RedLink Receiver Datasheet DESCRIPTION The Firecomms DC to 5 MBd Dual supply voltage RedLink receiver is based on a fully integrated photo-diode
More informationFM05DHIR FM05DVIR DC 5 MBd Dual Supply Voltage RedLink Receiver Preliminary Data Sheet
NOT RECOMMENDED FOR NEW DESIGNS * For new designs please see part numbers: FR05DHIR FR05DVIR FM05DHIR FM05DVIR DC 5 MBd Dual Supply Voltage RedLink Receiver Preliminary Data Sheet DESCRIPTION The Firecomms
More informationFeatures. Applications. Truth Table (Positive Logic) LED ENABLE OUTPUT
ACNVE mm DTI, MBd Digital Optocoupler Data Sheet Description The new ACNVE is an optically coupled gate that combines a AlGaAs light emitting diode and an integrated photo detector housed in a widebody
More informationAgilent HCPL-0738 High Speed CMOS Optocoupler
Agilent HCPL-078 High Speed CMOS Optocoupler Data Sheet Description The HCPL-078 is a dual-channel 1 MBd CMOS optocoupler in SOIC-8 package. The HCPL-078 optocoupler utilizes the latest CMOS IC technology
More informationHFD Mbit Direct Coupled Receiver
FEATURES Converts fiber optic input signals to TTL digital outputs Typical sensitivity 2 µw (-27 dbm) Single 5 V supply requirement Direct coupled receiver circuit Open collector output Microlens optics
More informationFiber Optic LAN Components VF45 Quad Transceiver for 10Mb/s and 100Mb/s Ethernet
FEATURES Key component for making a fiber optic Ethernet truly scalable and switchable from 10 to 100Mb/s Ethernet. Innovative NEW interconnect is cost competitive with copper solutions, thus enabling
More informationSchematic V F HCPL-7601/11 SHIELD. USE OF A 0.1 µf BYPASS CAPACITOR CONNECTED BETWEEN PINS 5 AND 8 IS REQUIRED (SEE NOTE 1).
CMOS/TTL Compatible, Low Input Current, High Speed, High CMR Optocoupler Technical Data HCPL-7601 HCPL-7611 Features Low Input Current Version of HCPL-2601/11 and 6N137 Wide Input Current Range: I F =
More informationFT50MxxR 650 nm DC-50 MBd Fully Integrated RedLink Fiber Optic Transmitter Datasheet
FT50MxxR 650 nm DC-50 MBd Fully Integrated RedLink Fiber Optic Transmitter Datasheet DESCRIPTION The Firecomms DC-50 MBd RedLink transmitter consists of a highly reliable Resonant Cavity Light Emitting
More informationFT50MHNR FT50MHIR FT50MVNR FT50MVIR 650 nm DC 50 MBd Fully Integrated RedLink Fiber Optic Transmitter Data Sheet
FT50MHNR FT50MHIR FT50MVNR FT50MVIR 650 nm DC 50 MBd Fully Integrated RedLink Fiber Optic Transmitter Data Sheet DESCRIPTION The Firecomms DC 50 MBd RedLink transmitter consists of a highly reliable Resonant
More informationData Sheet. HFBR-0300Z Series HFBR-1312TZ Transmitter HFBR-2316TZ Receiver nm Fiber Optic Transmitter and Receiver. Features.
HFBR-000Z Series HFBR-TZ Transmitter HFBR-TZ Receiver 00 nm Fiber Optic Transmitter and Receiver Data Sheet Description The HFBR-000Z Series is designed to provide the most cost-effective 00 nm fiber optic
More informationFM20VHIR FM20VVIR. RedLink Fiber Optic Receiver for Direct High Voltage Switching Preliminary Data Sheet DESCRIPTION FEATURES APPLICATIONS
FM0VHIR FM0VVIR RedLink Fiber Optic Receiver for Direct High Voltage Switching Preliminary Data Sheet DESCRIPTION This Firecomms RedLink receiver is based on a fully integrated photodiode with TIA, limiting
More information4N25 Phototransistor Optocoupler General Purpose Type. Features
4N Phototransistor Optocoupler General Purpose Type Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxe denotes a lead-free product Description The 4N is an
More informationDual Channel, High Speed Optocouplers Technical Data
Dual Channel, High Speed Optocouplers Technical Data HCPL-2530 HCPL-2531 HCPL-4534 HCPL-0530 HCPL-0531 HCPL-0534 Features 15 kv/µs Minimum Common Mode Transient Immunity at V CM = 1500 V (HCPL-4534/0534)
More informationFR20DxIR RedLink Fiber Optic Receiver for Direct High Voltage Switching Datasheet
FR0DxIR RedLink Fiber Optic Receiver for Direct High Voltage Switching Datasheet DESCRIPTION This Firecomms RedLink receiver is based on a fully integrated photodiode with TIA, limiting amplifier and a
More information1.52 (0.060) 20.8 (0.82) 11.7 (0.46) 1.78 ± 0.10 (0.070 ± 0.004) 2.92 ± 0.10 (0.115 ± 0.004) (0.400)
HEDS-9000/9100 Two Channel Optical Incremental Encoder Modules Data Sheet Description The HEDS-9000 and the HEDS-9100 series are high performance, low cost, optical incremental encoder modules. When used
More informationHFD3029. Schmitt Input, Non-Inverting TTL Output Receiver
FEATURES Converts fiber optic input signals to TTL totem pole outputs Sensitivity is 1.5 µw peak (-28.2 dbm) Single 5 V supply requirement Schmitt circuitry gives 17 db dynamic range and low Pulse Width
More informationHCPL-576x* AC/DC to Logic Interface Hermetically Sealed Optocouplers
HCPL-576x* 5962-8947701 AC/DC to Logic Interface Hermetically Sealed Optocouplers Data Sheet Description These devices are single channel, hermetically sealed, voltage/current threshold detection optocouplers.
More informationACPL-M50L, ACPL-054L, ACPL-W50L and ACPL-K54L Low Power, 1MBd Digital Optocoupler. Features. Applications GND
ACPL-M5L, ACPL-5L, ACPL-W5L and ACPL-K5L Low Power, MBd Digital Optocoupler Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxe denotes a lead-free product
More informationSFH551/1-1 and SFH551/1-1V Receiver with Digital Output Stage for Polymer Optical Fiber Applications. Data Sheet. Description.
and V Receiver with Digital Output Stage for Polymer Optical Fiber Applicatio Data Sheet Description The receiver is a traimpedance amplifier with an integrated photodiode and TTL open-collector output
More informationData Sheet. AFBR-3950xxRZ High Voltage Galvanic Insulation Link for DC to 50MBaud. Features. Description. Applications. Ordering Information
AFBR-3950xxRZ High Voltage Galvanic Insulation Link for DC to 50MBaud Data Sheet Description Avago Technolgies AFBR-3950xxRZ is a high voltage galvanic insulation link for DC to 50 MBaud. The AFBR- 3950xxRZ
More informationData Sheet. HCPL-181 Phototransistor Optocoupler SMD Mini-Flat Type. Description
HCPL-8 Phototransistor Optocoupler SMD Mini-Flat Type Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxe denotes a lead-free product Description The HCPL-8
More informationFR05DxDR RedLink Fiber Optic Receiver for Direct High Voltage Switching Datasheet
FR05DxDR RedLink Fiber Optic Receiver for Direct High Voltage Switching Datasheet DESCRIPTION This Firecomms RedLink receiver is based on a fully integrated photodiode with TIA, limiting amplifier and
More informationDual Channel, High Speed Optocouplers Technical Data
Dual Channel, High Speed Optocouplers Technical Data HCPL-5 HCPL-5 HCPL-454 HCPL-5 HCPL-5 HCPL-54 Features 5 kv/µs Minimum Common Mode Transient Immunity at V CM = 5 V (HCPL-454/54) High Speed: Mb/s TTL
More informationEuropean Connectorized Receivers
European Connectorized Receivers Honeywell receiver components are available in the following connector styles. Each style has a three-digit reference used in the order guides. SMA SINGLE HOLE MOUNTING
More informationACNT-H50L. 1-MBd Optocoupler in 15-mm Stretched SO8 Package. Data Sheet. Description. Features. Applications. Functional Diagram
ACNT-H5L -MBd Optocoupler in 5-mm Stretched SO8 Package Description The ACNT-H5L is a single-channel -MBd optocoupler in Stretched SO8 footprint. It uses an insulating layer between the light emitting
More informationFeatures. Applications
HCPL-9000/-0900, -900/-090, HCPL-90/-09, -900J/-090J, HCPL-90J/-09J, -90J/-09J High Speed Digital Isolators Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxe
More informationData Sheet. HCPL-181 Phototransistor Optocoupler SMD Mini-Flat Type. Features
HCPL-8 Phototransistor Optocoupler SMD Mini-Flat Type Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxe denotes a lead-free product Description The HCPL-8
More informationFeatures. Applications OFF
HCPL Power Bipolar Transistor Base Drive Optocoupler Data Sheet Description The HCPL consists of a Silicondoped GaAs LED optically coupled to an integrated circuit with a power output stage. This optocoupler
More informationDistributed by: www.jameco.com -8-8-22 The content and copyrights of the attached material are the property of its owner. HCPL-M, HCPL-M, HCPL-M Small Outline, Lead, High CMR, High Speed, Logic Gate Optocouplers
More informationData Sheet. AFBR-16xxZ and AFBR-26x4Z/25x9Z DC-50MBd Versatile Link Fiber Optic Transmitter and Receiver for 1 mm POF and 200 m PCS.
AFBR-6xxZ and AFBR-6x4Z/5x9Z DC-50MBd Versatile Link Fiber Optic Transmitter and Receiver for mm POF and 00 m PCS Data Sheet Description The AFBR-6xxZ transmitter utilizes a 650 nm LED source with integrated
More information8.6 (0.34) 1.52 (0.060) 20.8 (0.82) 11.7 (0.46) 1.78 ± 0.10 (0.070 ± 0.004) 2.92 ± 0.10 (0.115 ± 0.004) 10.2 (0.400)
HEDS-9200 Series Linear Optical Incremental Encoder Modules Data Sheet Note: Codestrip not included with HEDS-9200 Description The HEDS-9200 series is a high performance, low cost, optical incremental
More informationData Sheet. HFBR-1312TZ Transmitter HFBR-2316TZ Receiver nm Fiber Optic Transmitter and Receiver. Description. Features.
HFBR-11TZ Transmitter HFBR-1TZ Receiver 100 nm Fiber Optic Transmitter and Receiver Data Sheet Description The HFBR-11TZ Transmitter and HFBR-1TZ Receiver are designed to provide the most cost-effective
More informationAC/DC to Logic Interface Optocouplers Technical Data
H AC/DC to Logic Interface Optocouplers Technical Data HCPL-37 HCPL-376 Features Standard (HCPL-37) and Low Input Current (HCPL-376) Versions AC or DC Input Programmable Sense Voltage Hysteresis Logic
More informationAFBR-5972Z Compact 650nm Transceiver with Compact Versatile-Link connector for Fast Ethernet over POF. Features. Applications
AFBR-5972Z Compact 65nm Transceiver with Compact Versatile-Link connector for Fast Ethernet over POF Data Sheet Description The AFBR-5972Z Transceiver provides the system designer with the ability to implement
More informationCopper Leadframe for Improved Thermal and Optical Characteristics
High-Performance T- 3 /4 (5 mm) TS AlGaAs Infrared (875 nm) Lamp Technical Data HSDL-42 Series HSDL-422 3 HSDL-423 7 Features Very High Power TS AlGaAs Technology 875 nm Wavelength T- 3 /4 Package Low
More informationApplication Note 5341
Driver and Receiver Circuits for Avago SFH Series Plastic Fiber Components (PFC) Application Note 5341 SFH Series Components In addition to data transmission at 82 nm and 13 nm, transmission at 65 nm is
More information1300nm Fast Ethernet Transceiverin1x9SC Duplex Package
1300nm Fast Ethernet Transceiverin1x9SC Duplex Package OPF5102 Technical Data Features 1310nm LED Data Rate: 155Mbps, NRZ Single +3.3V Power Supply PECL Differential Electrical Interface Industry Standard
More informationAFBR-59F3Z Compact 650 nm Transceiver for 1 Gbps Data communication MLCC (Multilevel Coset Coded) over POF (Polymer Optical Fiber) Features
AFBR-59F3Z Compact 650 nm Transceiver for 1 Gbps Data communication MLCC (Multilevel Coset Coded) over POF (Polymer Optical Fiber) Data Sheet Description The Avago Technologies' AFBR-59F3Z transceiver
More informationFiber Optic Receiver. OPF520 Series. OPF520 Series
Low Cost plastic cap package Designed to self align in the bore of standard fiber optic receptacles Press fit simplifies installation Optimized for fiber optic applications using 50 to 200 micron fiber
More informationDistributed by: www.jameco.com 1-800-831-4242 The content and copyrights of the attached material are the property of its owner. HFBR-0400 Series HFBR-14xx Transmitters HFBR-24xx Receivers Low Cost, Miniature
More informationLTV-063L LVTTL/LVCMOS Compatible 3.3V Dual-Channel Optocouplers (10 Mb/s)
LTV-063L LVTTL/LVCMOS Compatible 3.3V Dual-Channel Optocouplers (10 Mb/s) Description The LTV-063L consists of a high efficient AlGaAs Light Emitting Diode and a high speed optical detector. This design
More informationHCPL-5300, HCPL-5301, HCPL-530K,
HCPL-00, HCPL-0, HCPL-0K, 9-9 Intelligent Power Module and Gate Drive Interface Hermetically Sealed Optocouplers Description The HCPL-0x devices consist of a GaAsP LED optically coupled to an integrated
More informationHigh Speed CMOS Optocouplers. Technical Data HCPL-7100 HCPL Features. Description. Applications. Schematic
H High Speed CMOS Optocouplers Technical Data HCPL-7100 HCPL-7101 Features 1 µm CMOS IC Technology Compatibility with All +5 V CMOS and TTL Logic Families No External Components Required for Logic Interface
More informationData Sheet. AFBR-1150L / AFBR-2150L Fiber Optic Transmitter and Receiver for 150 Mbit/s MOST. Features. Description. Applications.
AFBR-1150L / AFBR-2150L Fiber Optic Transmitter and Receiver for 150 Mbit/s MOST Data Sheet Description MOST150 transmitter and receiver are designed to transmit/ receive up to 150 MBit/s optical data
More informationAgilent 4N35 Phototransistor Optocoupler General Purpose Type
Agilent N3 Phototransistor Optocoupler General Purpose Type Data Sheet Description The N3 is an optocoupler for general purpose applications. It contains a light emitting diode optically coupled to a phototransistor.
More informationAFBR-5972EZ, AFBR-5972BZ Compact 650nm Transceiver with Compact Versatile Link Connector for Fast Ethernet over POF. Features.
AFBR-5972EZ, AFBR-5972BZ Compact 65nm Transceiver with Compact Versatile Link Connector for Fast Ethernet over POF Data Sheet Description The AFBR-5972xZ transceivers provide system designers with the
More informationData Sheet. HFBR-1312T Transmitter HFBR-2316T Receiver 1300 nm Fiber Optic Transmitter and Receiver. Description. Features. Applications.
HFBR-11T Transmitter HFBR-1T Receiver 100 nm Fiber Optic Transmitter and Receiver Data Sheet Description The HFBR-000 Series is designed to provide the most cost-effective 100 nm fiber optic links for
More informationOptically Coupled 20 ma Current Loop Receiver. Technical Data HCPL-4200
H Optically Coupled 2 ma Loop Receiver Technical Data OPTOCOUPLERS HCPL-42 Features Data Output Compatible with LSTTL, TTL and CMOS 2 K Baud Data Rate at 14 Metres Line Length Guaranteed Performance over
More informationHFD /XXX. h 479. Schmitt Input, Non-Inverting TTL Output Receiver
FEATURES Converts fiber optic input signals to TTL totem pole outputs Maximum sensitivity 1.5 µw peak (-28.2 dbm) Wide variety of cable options, operates with 50/125, 62.5/125, and 100/140 µm cables Schmitt
More informationACPL-P480 and ACPL-W480
High CMR Intelligent Power Module and Gate Drive Interface Optocoupler Description The high-speed ACPL-P48/W48 optocoupler contains a GaAsP LED, a photo detector, and a Schmitt trigger that eliminates
More informationACNV4506 Intelligent Power Module and Gate Drive Interface Optocouplers. Features. Specifications. Applications
ACNV0 Intelligent Power Module and Gate Drive Interface Optocouplers Data Sheet Description The ACNV0 device contains a GaAsP LED optically coupled to an integrated high gain photo detector. Minimized
More informationMIC5202. Dual 100mA Low-Dropout Voltage Regulator. Features. General Description. Pin Configuration. Ordering Information. Typical Application
MIC MIC Dual ma Low-Dropout Voltage Regulator Preliminary Information General Description The MIC is a family of dual linear voltage regulators with very low dropout voltage (typically 7mV at light loads
More informationData Sheet. AFBR-59E4APZ Multimode Small Form Factor (SFF) Transceiver for Fast Ethernet, with LC connector. Description. Features.
AFBR-59E4APZ Multimode Small Form Factor (SFF) Transceiver for Fast Ethernet, with LC connector Data Sheet Description The AFBR-59E4APZ is a new power saving Small Form Factor transceiver that gives the
More informationHEDS-9000/9100 Two Channel Optical Incremental Encoder Modules. Features. Applications
HEDS-9000/9100 Two Channel Optical Incremental Encoder Modules Data Sheet Description The HEDS-9000 and the HEDS-9100 series are high performance, low cost, optical incremental encoder modules. When used
More informationHCPL-M454 Ultra High CMR, Small Outline, 5 Lead, High Speed Optocoupler. Features
HCPL-M44 Ultra High CMR, Small Outline, Lead, High Speed Optocoupler Data Sheet Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxe denotes a lead-free product Description
More informationPhotocoupler Product Data Sheet LTV-063L Spec No.: DS Effective Date: 07/06/2016 LITE-ON DCC RELEASE
Product Data Sheet LTV-063L Spec No.: DS70-2016-0042 Effective Date: 07/06/2016 Revision: - LITE-ON DCC RELEASE BNS-OD-FC001/A4 LITE-ON Technology Corp. / Optoelectronics No.90,Chien 1 Road, Chung Ho,
More informationHIGH SPEED-10 MBit/s LOGIC GATE OPTOCOUPLERS
HIGH SPEED- MBit/s DESCRIPTION The, /6 single-channel and /6 dual-channel optocouplers consist of a 5 nm AlGaAS LED, optically coupled to a very high speed integrated photodetector logic gate with a strobable
More informationHCPL-270L/070L/273L/073L
Low Input Current, High Gain, LVTTL/LVCMOS Compatible Optocouplers Description These high gain series couplers use a Light Emitting Diode and an integrated high gain photodetector to provide extremely
More informationData Sheet. AEDT-9140 Series High Temperature 115 C Three Channel Optical Incremental Encoder Modules 100 CPR to 1000 CPR. Description.
AEDT-9140 Series High Temperature 115 C Three Channel Optical Incremental Encoder Modules 100 CPR to 1000 CPR Data Sheet Description The AEDT-9140 series are three channel optical incremental encoder modules.
More informationLM111/LM211/LM311 Voltage Comparator
LM111/LM211/LM311 Voltage Comparator 1.0 General Description The LM111, LM211 and LM311 are voltage comparators that have input currents nearly a thousand times lower than devices like the LM106 or LM710.
More informationHigh CMR Intelligent Power Module and Gate Drive Interface Optocoupler. Features. Specifications. Applications
ACPL-P80 and ACPL-W80 High CMR Intelligent Power Module and Gate Drive Interface Optocoupler Data Sheet Lead (Pb) Free RoHS fully compliant RoHS fully compliant options available; -xxxe denotes a lead-free
More informationFeatures 8.6 (0.34) 1.52 (0.060) 20.8 (0.82) 11.7 (0.46) 1.78 ± 0.10* (0.070 ± 0.004) 2.92 ± 0.10** (0.115 ± 0.004) 10.2 (0.400)
HEDS-92 Series Linear Optical Incremental Encoder Modules Data Sheet Note: Codestrip not included with HEDS-92 Description The HEDS-92 series is a high performance, low cost, optical incremental encoder
More informationACNV2601. High Insulation Voltage 10-MBd Digital Optocoupler. Data Sheet. Description. Features. Applications
High Insulation Voltage -MBd Digital Optocoupler Description The ACNV26 is an optically coupled gate that combines an AlGaAs light-emitting diode and an integrated photo detector housed in a widebody package.
More informationFeatures. Applications
HLMP-NS31 and HLMP-NM31 T-1 (3mm) InGaN LED Lamps Data Sheet Description These InGaN lamps are designed in industry standard package with clear and non-diffused optics. These lamps are ideal for use as
More informationApplication Note 5342
General Information for Avago SFH series Plastic Fiber Components (PFC) Application Note 5342 Introduction Optical communications offer important advantages over electrical transmission links. The following
More informationCD74HC4067, CD74HCT4067
Data sheet acquired from Harris Semiconductor SCHS209 February 1998 CD74HC4067, CD74HCT4067 High-Speed CMOS Logic 16-Channel Analog Multiplexer/Demultiplexer [ /Title (CD74 HC406 7, CD74 HCT40 67) /Subject
More information