Husky Techtray. S m a r t C a b l e M a n a g e m e n t. Introduction Pg. 169

Transcription

1 Introduction Pg. 169 Husky Techtray Quality Information Pg. 170 Features & Benefits Pg. 171 Fill Chart / Load Tables Pg. 172 Numbering System Pg. 173 Quick Connect System Pgs Connectors & Fittings Pgs Cutting the Tray Pgs Supports & Covers Pgs Accessories Pg S m a r t C a b l e M a n a g e m e n t

2 CABLE BUS Table of Contents Introduction... Pg. 169 Quality Information...Pg. 170 Features & Benefits...Pg. 171 Fill Chart / Load Tables...Pg. 172 Numbering System... Pg. 173 Quick Connect System...Pgs Connectors & Fittings...Pgs Cutting the Tray... Pgs Supports & Covers...Pgs Accessories... Pg MP Husky Techtray is... Smart Cable Management! 168

3 Introduction MP Husky has been in the Cable Tray business since Over the past 50+ years of leadership and service, MP Husky has gone through several transformations and mergers, including Husky/Burndy and Metal Products, thus leading to what is today MP Husky America s leading manufacturer of Cable Tray and Cable Bus Power Distribution Systems. Throughout these changes one thing has remained constant the Husky drive to be the most reliable, highest quality, cost effective and innovative manufacturer of Cable Support Systems and Cable Bus Power Distribution Systems. We have an unsurpassed commitment to customer satisfaction and service, and we are eager to earn your loyalty and trust. CABLE BUS Suggested Techtray Specification Product Description: Techtray is a wire mesh cable tray system that utilizes high mechanical strength steel wire that is welded into a grid system. This grid system is then formed into channels which support and carry cables. The wire mesh will consist of a 2 x 2 grid system, and will utilize wires that have a minimum diameter of.16 (4mm). Material: Standard tray finish shall be mill-galvanized. Other finish options include Electroplated Zinc, Hot Dipped Galvanized after Fabrication, Clear Zinc, Painted or Stainless Steel. Safety Edge: Wire mesh system shall have continuous top edge wire that is T-Welded on top of support wires to avoid sharp edges that may damage cable or installer. Fittings: Shall be fabricated in the field by cutting wires with a cutting device. Cuts shall be made in a manner reducing sharp edges and projections so they do not harm cables or installation personnel. Manufacturer shall offer corner connectors that provide a radius on the inside corner of bends for horizontal 90 degree bends, tees, and crosses. Straight sections shall be provided in 10 (3m) lengths. Wire mesh shall be welded at all intersections. Mesh system will permit continuous ventilation of cables and maximum disposition of heat. Tray shall be manufactured in accordance with NEMA VE-1 and shall be installed in accordance with NEMA VE

4 Quality Our Quality Policy At MP Husky we are committed to producing only the highest quality products that meet or exceed our customers expectations and requirements. Our goal is to achieve 100% customer satisfaction by delivering the best products and services on-time and defect free. We will achieve this individually and corporately through tested and proven processes and controls, in our Quality System, and with a constant focus and effort on continuous improvement. Item Standards MP Husky Quality Program ANSI / ASQC Q (ISO 9001 Compliant) ASME NQA ANSI N45.2 Certification CSA Certified UL Classified Load Test Standards NEMA VE-1/CSA Tray Standards Customer Testimonial MP Husky Techtray is truly Smart Cable Management. It is simple, fast to install, and very cost effective. The T-Weld safety edge, as well as the strong and modular 2 x 2 grid design make Techtray perfect for handling sensitive cables. Another great benefit is there are no custom fittings and very few accessories for installation. Industrial Electrical Contractor 170

5 CABLE BUS Features & Benefits UL Classified MP Husky Techtray meets or exceeds all applicable UL standards. CSA Certified (Canadian Standards Association) MP Husky Techtray is CSA certified to CSA E22.2 no NEMA MP Husky Techtray has been tested in accordance with NEMA VE-1. Cost Effective Our tough, lightweight design along with a few of our simple accessories is all you need to complete an entire cable management application. Safe Our Safety Edge T Weld design eliminates sharp edges, which can damage sensitive cables, it also protects the installers from unwanted cuts and scratches. To provide sensitive cable additional safety, our unique 2 x 2 wire mesh grid design provides the safest and most complete support system available. Fast, Simple Installation MP Husky s Smart Tab System is the fastest and simplest way to support, splice and connect Wire Mesh Cable Tray. All you need is an open end wrench or a straight blade screwdriver. Strength in Numbers Our unique 2 x 2 grid offers twice the support of 2 x 4 systems, providing strong and safe support of your sensitive Telecom/ Data and Fiber Optic cables. Field Flexible Since there are no custom fittings to order, and our tray is easily manipulated with a few simple tools, you can easily create any bend, drop, or intersection to maneuver around obstacles in the field. Lightweight Design Our lightweight yet strong design allows for ease of installation and less parts to suspend the system, saving time and money. Quick Delivery Available for quick delivery from our stock. Smart 90 Corner Splice Our unique 90 Corner Splice connector has been designed to provide a stronger radius corner connection for the inside corner of 90 bends, tees and crosses. 171

6 Wire Basket Cable Fill Chart Per the National Electrical Code Article 392-9(b) trays may be filled 50% when using control or signal wiring. The sum of the cross sectional areas of all cables cannot exceed 50% of the trays fill area. The cable tray fill area equals the width times the loading depth. Generally, the tray will appear full of cables when it contains a 50% fill of cables. Tray Size Load Tests # of O.D. Cables #0.21 O.D. Cables #0.23 O.D. Cables #0.25 O.D. Cables 2 x x x x x x x x x x x x x x x x x x x x x x x x The chart below represents the results of the load tests on MP Husky s Techtray, as it was tested in accordance with NEMA-VE1 / CSA E22.2 No The safety factor is 1.5. Tray Tray Size 1.5M 5ft. 1.82M 6ft. 2.13M 7ft. 2.43M 8ft. Series Inches MM KG/M LBS/ft KG/M LBS/ft KG/M LBS/ft KG/M LBS/ft WB x x WB x x WB x x WB x x WB x x WB x x WB x x WB x x WB x x

7 CABLE BUS Catalog Numbering System Example below is 2 x 2 grid, 2 deep, 6 wide and 10 long, HDGAF finish G WB Finish Type Tray Type Wire Basket Grid Size (Width x Length) Tray Depth Tray Width (in.) Tray Length (in.) Pre-Galvanized is our standard finish - no prefix required. G=HDGAF Z=Clear Zinc Elect. 4=304SS 6=316SS Wire Mesh Cable Tray 2 x , 4 6, 8 10, 12 14, 16 18, 20 22, Note: Some size combinations are not available. Splice connectors must be ordered seperately. For Painted Tray - put color code at the end of the part number. Example GWB RED. Width Load Depth Catalog Number 2 /50mm 2 /50mm WB /100mm 2 /50mm WB /150mm 2 /50mm WB /200mm 2 /50mm WB /300mm 2 /50mm WB /400mm 2 /50mm WB /450mm 2 /50mm WB /550mm 2 /50mm WB /600mm 2 /50mm WB /700mm 2 /50mm WB The above chart shows the part numbers based on 2 tray depth. This catalog number is for standard finish tray. Width Load Depth Catalog Number 4 /100mm 4 /100mm WB /200mm 4 /100mm WB /300mm 4 /100mm WB /350mm 4 /100mm WB /450mm 4 /100mm WB /500mm 4 /100mm WB /600mm 4 /100mm WB The above chart shows the part numbers based on 4 tray depth. This catalog number is for standard finish tray. Width Load Depth Catalog Number 8 /200mm 6 /150mm WB /250mm 6 /150mm WB /350mm 6 /150mm WB /450mm 6 /150mm WB /500mm 6 /150mm WB /600mm 6 /150mm WB The above chart shows the part numbers based on 6 tray depth. This catalog number is for standard finish tray. 173

8 CABLE BUS Husky Quick Connect System - Boltless Connections Made Easy MP Husky s Quick Connect System is the fastest and simplest way to splice, connect and support Wire Mesh Cable Tray. No more fumbling with hardware and multiple tools to install splice connections or supports. All you need is an open end wrench or a straight blade screwdriver. Installation has never been this quick and easy! Quick Splice The MP Husky Quick Splice eliminates fumbling with hardware and multiple tools to make splice connections. The Quick Splice provides a gap of ¼ between jointing sections to provide a strong, tight connection, as well as allow for cut wire ends. This part can be installed quickly with an open end wrench (several sizes will work), or a screwdriver (straight blade or cross point), eliminating the need for any special tools. The Quick Splice is the fastest, easiest, strongest way to make splices. Quick Splice Part No. QS Quick Splice Clip Another fast and simple boltless splice clip from MP HUS- KY, commonly used for fabricating sweeps and bends in the field. Use standard pliers to fold locking tabs to secure standard quick clip - no hardware necessary. (Also available with a back plate and hardware to make a bolted connection.) Mounting hardware is included. Pre-Galvanized finish is standard. Other finishes available. Quick Splice Clip Part No. WB-SCQ (without back) Part No. WB-SCWB (with back) Quick Hanger Like our Quick Splice, the MP Husky Quick Hanger eliminates fumbling with hardware and multiple tools to hang the tray. This part can be installed quickly with an open end wrench (several sizes will work), or a screwdriver (straight blade or cross point), eliminating the need for any special tools. Quick Hanger Part No. QH (Patent Pending) 174

9 CABLE BUS Quick Connect System Trapeze Hanger Bend down retaining tabs on 2 centers. 5/16 and 7/16 holes on each end for 1/4 and 3/8 hanger rods. Part No. WBSTHS-W W = insert width Smart Tab Trapeze Hanger Wall Bracket Provides fast, efficient and economical support of your Husky Techtray system. To install, position the tray on the Smart Tab, slide the tray beneath the tab and lock into position. No hardware is required. Part No. WBSVBK-W Bend down tabs on 2 centers. 5/16 holes on 2 centers. W = insert width Smart Tab Wall Bracket Wall Bracket & Under Floor Bracket We offer a L bracket support for 2 to 22 wide Husky Techtray. This bracket can be used for wall mount or under floor mount utilizing different hardware. Wall Bracket Under Floor Bracket Tray Width (in.) Wall Part # Under Floor Part # Length (in.) 22 WBSWLB-22 WBSUFB WBSWLB-20 WBSUFB WBSWLB-18 WBSUFB WBSWLB-16 WBSUFB WBSWLB-14 WBSUFB WBSWLB-12 WBSUFB WBSWLB-10 WBSUFB WBSWLB-8 WBSUFB WBSWLB-6 WBSUFB WBSWLB-4 WBSUFB WBSWLB-2 WBSUFB Pole Bracket We offer a Two Pole Support Bracket when complete support is needed between floor posts. Includes all hardware necessary to support tray between two floors. 2 Pole Smart Tab Bracket Part No. WBSPSB-138 (for post sizes 1-1-3/8 ) Part No. WBSPSB-200 (for post sizes 1-1/2-2 ) 175

10 Connectors & Fittings Splice Connector Clamps two Techtray sections together easily and reliably. The inner grooved plate clamps the vertical side wires to the outer L-shaped plate, which also levels and supports the horizontal wires. Bonding jumpers are not required with this splice. Splice Connector Splice connectors & hardware are sold separately. Part No. SSP-WB2 Vertical Adj. Splice Connector Overcome obstacles with the Vertical Adjustable Splice Connector, which can be used to change the elevation of the cable tray routing. Firmly clamps to mesh. Hardware included. Bonding jumper required. Vertical Adj. Splice Connector Part No. SFS-VWB2 (Note: one angle only, one side of tray should be ordered in pairs) Universal Splice Splice Bar is used for assembly of large radius fittings or to adapt to width change or form offsets. (Includes 2ea. WBHDC, 2 nuts, 2 bolts) Universal Splice Bar Part No. WB-SB 90 Degree Horizontal Bend Connector Kit By overlapping and clamping into place, field cutting is minimized yet cable support and protection is maximized. Each kit includes two back plates, one L corner plate, nuts and bolts. 90 Horizontal Bend Connector Kit Part No. SSP

11 CABLE BUS Connectors & Fittings Tee Connector Tee Connector Requires two SSP-90-2 kits (shown on previous page) to form a sturdy Tee connection. Hardware is included. Part No. SSP-90-2 (Note: 2 are required) Cross Connector Four SSP-90-2 kits (shown on previous page) are required to complete a crossover. Remove a section of each basket sidewall, overlap, and connect. Hardware is included. 1/4 hardware (not shown) Cross Connector Part No. SSP-90-2 (Note: 4 are required) 1/4 hardware (not shown) Splice Clamp The Splice Clamp is used whenever two wires need to be fastened together, such as when making segmented fittings (shown below) in the field. Splice Clamp Part No. WB-SC 90 Long Radius Horizontal Splice Flex Kit Used to create horizontal angles from prepared wire basket straight sections. Top and bottom plates have humps to grip wires. Horizontal Splice Flex Kit Part No. SFS-HWB2 Horizontal Short Radius 177

12 Connectors & Fittings Reducing Splice Kit & Splice Bar Reducing Splice Kit & Splice Bar Used to create reductions in width of trays. Hardware included. Part No. SSP-WBOR Horizontal Flex Splice Kit Cut wires as shown and form by hand. A standard connection plate and back plate secure the assembly. Top plate has humps to grip wires, bottom plate is flat. Part No. SR Horizontal Short Radius Horizontal Flex Splice Kit T-WELD REMOVE SECTION AND FORM BY HAND OVERLAPPING ONE SECTION Vertical Offset For vertical inside and vertical outside bends, side wires are cut and removed, as shown. The basket may then be formed to the required radius. The 2 grid provides cable support even on long sweeps, without the need for vertical radius plates used on 4 grid basket trays. Vertical Offset 178

13 CABLE BUS Examples of Cutting the Tray Below are examples showing how the tray is cut to form various degree bends. Splice Clamps are used whenever two wires need to be fastened together, such as when making segmented fittings (shown below) in the field. (Part #WB-SC) 30 Degree Bend 45 Degree Bend 60 Degree Bend 90 Degree Bend 179

14 Examples of Cutting the Tray CABLE BUS When making these radiused horizontal fittings, the outside of the tray will not be cut. Only cut the bottom and the inside side of the tray. To remove a 2 row, cut the longitudinal wires between two transverse wires, on the bottom and inside of the bend. When removing more than one 2 row a transverse wire will be removed for each additional row being removed. Once the proper number of rows have been removed, the inside wires are pulled together and joined using a splice clip. For non-radiused horizontal bends, simply cut one side out of the adjoining trays and lay one tray on top of the other so they can be connected using the horizontal flex splice kit (Part #SFS-HWB2). The wires need to be removed from the corner of the perpendicular piece. Horizontal Tees and Crosses When making tees or crosses, the perpendicular bottom may be up against the straight through member. In this case, one side block is removed from all intersecting corners, so that the tee connector can form a radiused corner. If the perpendicular member is overlapped, one square on the bottom, then two sections need to be removed from the corners of the perpendicular piece. Vertical Bends Vertical bends are made by cutting the upper side wires and bending the basket up or down. 12H90 The above example shows the cutting pattern that would be used to create a 90 degree bend on 12 wide tray. To make a tighter radius, only leave one row in between the sections that are cut. 12H60 The above example shows the cutting pattern that would be used to create a 60 degree bend on 12 wide tray. To make a tighter radius, only leave one row in between the sections that are cut. 12H45 The above example shows the cutting pattern that would be used to create a 45 degree bend on 12 wide tray. To make a tighter radius, only leave one row in between the sections that are cut H30 The above example shows the cutting pattern that would be used to create a 30 degree bend on 12 wide tray. To make a tighter radius, only leave one row in between the sections that are cut.

15 CABLE BUS Cutting the Wire Basket Below is a chart detailing how to cut horizontal fittings on Husky Techtray. The green columns are rows that should be removed (cut) and the orange columns are rows that should be left in place (skipped). If the column says to skip one or more, the more rows you skip, the longer the radius will be. There are examples of how to cut tray on Page 13 for your reference. For further details, please consult the factory. WIRE BASKET HORIZONTAL FITTING CUTTING CHART **See Pages for examples** 181

16 Cutting the Wire Basket (Repeat sequence 6 times total) (Repeat sequence 9 times total) 182

17 Supports and Covers Center Hanger Support MP Husky s WBCHC Smart Center Hanger Clip provides a true center hung installation in all Husky Techtray widths and can be used when the WBHDC clamp will not conform to the true center of the tray. Clamp & hardware included. Hanger rod sold separately. Center Hanger Support Part No. WBCHC (1/4 rod) WBCHC-3/8 (3/8 rod) Universal Hanger Support MP Husky offers a new universal hanger support. This universal support hanger can be used as a center hung style support or a trapeze style support. This support can be used with 1/4 or 3/8 hanger rods. Hanger rods, nuts, bolts, and screws purchased separately. Part # Bar Width WBUS WBUS WBUS Each support includes a WBUS WBUS WBHDC-3/8 Hold Down Clamp. WBUS When using the 1/4 rod or 1/4 WBUS hardware, use W-13 Flat Washers WBUS-8 12 as required. WBUS-6 10 WBUS-4 8 WBUS-2 6 Universal Hanger Support HANGER ROD SUPPLIED SEPARATELY (1/4 OR 3/8 ) HANGER ROD SUPPLIED SEPARATELY (1/4 OR 3/8 ) 2-Pole Support Bracket We offer a Two Pole Support Bracket when complete support is needed between floor posts. Includes all hardware necessary to support tray between two floor support posts. 2-Pole Support Bracket Part No. WBPSB-138 (for post sizes 1-1-3/8 ) Part No. WBPSB-200 (for post sizes 1-1/2-2 ) WBHDC Hold Down is included. 183

18 Supports and Covers Under Floor Bracket MP Husky offers a full range of supports and connectors to provide a complete wiring pathway in raised floor computer room applications. We offer an L bracket support for 2 to 22 wide Husky Techtray. Our clamp only requires one 3/8 x 1 square head bolt for ease of installation. A. L Bracket or B. Bracket clamp C. 3/8 x 1 square bolt D. WBHDC hold-down clamp with hardware to attach tray to L bracket C B Under Floor Bracket D A Part No. WBUFB-(W) (W=width) - Hardware included. Under Floor Support We offer a 6 Floor Support that includes a WBHDC hold-down clamp and hardware to attach tray to floor plan. (10 L x 9-1/2 W x 6 H) Under Floor Support Part No. WBUFP-6 Hardware included. Floor Mount We offer a 1 Floor Mount that includes a WBHDC hold-down clamp to attach tray to floor plan. Floor Mount Part No. WBFS-1 Hardware included. Side Hanger Clamp For trapeze type supports, this clamp attaches 1/4 threaded rod to the side of the cable tray. Side Hanger Clamp 1/4 Hanger Rod Sold Separately Part No. WBVHC 3/8 also available part #WPVHC-3/8 184

19 CABLE BUS Supports and Covers Wall Bracket This bracket is used to mount tray from walls or other structures. Tray can be mounted with one WBHDC hold down clamp, which is included. Wall bracket mounts with two 3/8 hex head cap screws. (WBHDC Hold Down Clamp and Screws are not included). Wall Bracket Hold Down Clamp Part No. WBWLB-( ) ( ) = insert tray width Wall Bracket This bracket is used to mount trays from walls or other structures. Tray can be mounted with one or two WBHDC hold down clamps. Wall bracket mounts with two 3/8 hex head cap screws. (WBHDC Hold Down Clamps and Cap Screws are not included). Wall Bracket Part No. WBVBK-(W) (W) - insert tray width Flanged Covers Flanged covers for Husky Techtray are available for all Husky Techtray widths. Our WBCC cover clamp is available for all depths. Tray Width Part Numbers 2 WBCF WBCF WBCF WBCF WBCF WBCF WBCF WBCF WBCF WBCF WBCF WBCF WBCF WBCF 120 Flanged Covers WBCC COVER CLAMPS Tray Depth Part # H 2 WBCC-2 2-1/2 4 WBCC-4 4-1/2 6 WBCC-6 6-1/2 (use 6-8 clips per cover) H 185

20 Accessories Box Connector A box connector is used when you need to terminate a Husky Techtray run to an enclosure, a wall, or some other junction to a flat perpendicular surface. Includes mounting hardware. Box Connector Part No. WBBC-(W) Tray Width Part Numbers W 2 WBBC-2 2-1/4 4 WBBC-4 4-1/4 6 WBBC-6 6-1/4 8 WBBC-8 8-1/4 10 WBBC /4 12 WBBC /4 14 WBBC /4 16 WBBC /4 18 WBBC /4 20 WBBC /4 22 WBBC /4 24 WBBC /4 28 WBBC /4 End Plate Blind end plates are available for Husky Techtray and are furnished with mounting hardware. (Insert 2, 4 or 6 for depth of tray in place of D ) End Plate Part No. WBEP-(D)-(W) Tray Width Part Numbers W 2 WBEP( D )-2 2-1/4 4 WBEP( D )-4 4-1/4 6 WBEP( D )-6 6-1/4 8 WBEP( D )-8 8-1/4 10 WBEP( D ) /4 12 WBEP( D ) /4 14 WBEP( D ) /4 16 WBEP( D ) /4 18 WBEP( D ) /4 20 WBEP( D ) /4 22 WBEP( D ) /4 24 WBEP( D ) /4 28 WBEP( D ) /4 Drop Outs End style Drop Outs are available for use at the ends of tray sections, providing a radius for the cables to drop over. Includes mounting hardware. Drop Outs Part No. WBD-(W) Tray Width Part Numbers W 2 WBD WBD WBD WBD WBD WBD WBD WBD WBD WBD WBD WBD WBD

21 CABLE BUS Accessories Hold Down Clamp Unique saddle-type assembly plate allows Husky Techtray sections to be securely clamped into place as needed. Hold Down Clamp Part No. WBHDC Hardware not included. Inside Radius Corner Shield Provides a smooth inside radius surface for 90 horizontal bend. Inside Radius Corner Shield 1/4 hardware (not shown) Part No. WB-CG Conduit & Cord Adapter Plate For conduit connectors or cord grips, this plate bolts onto the side of the cable tray. Hole size is 1-1/16. Conduit fittings and cord connectors are not included. Conduit & Cord Adapter Plate Part No. WBVDS-3/4 or WBVDS-1 (for 3/4 and 1 EMT) Bonding Jumper Bonding Jumpers are used to maintain electrical continuity across hinge and expansion splices. 4-1/2 L for 1/4 Hardware (#12 Wire equivalent) Bonding Jumper Part No. AFS-WBC Braided Tinned Copper Jumper Hardware not included. 187

22 Accessories Wall Penetration Sleeve MP Husky s Wall Penetration Sleeve is used when tray has to pass through a wall. Includes 24 long pan, cover and two wall mounting flanges. Clamps included to fasten the wire basket to the pan. Wall Penetration Sleeve Part No. PWPS-(W)-WB2 (D) W = width D = depth Barrier Strips Barrier strips are available for Husky Techtray when cable separation is necessary. These separators come in 2 through 6 heights and are slotted at regular intervals for ease of installation without field drilling. Each barrier strip is furnished with the hardware necessary to install in the Husky Techtray. The standard length is 10ft. for straight sections and 4ft. for horizontal sections. Barrier Strips CSS Separator Splice Our CSS Separator Splice (sold separately) is applied to ensure a smooth transition between barrier strips. Part No. CSS For Straight Lengths Height Mill-Galvanized 2 S2S-120-WB 4 S4S-120-WB 6 S6S-120-WB For Horizontal Bends Height Mill-Galvanized 2 S2S-HA-WB 4 S4S-HA-WB 6 S6S-HA-WB Grounding MP Husky recommends using a split-bolt for connecting external ground wires to our Husky Techtray. We offer two types for you to choose from. WB-GB divides the copper wire from the basket steel wire. The WB-29 pulls the bare ground wire against the steel basket wire. Part No. WB-GB For #8 - #6 wire, 100A - 200A (tin plated) Grounding Part No. WB-29 For #10 - #6 wire (non-plated) 188

23 CABLE BUS Accessories & Hardware Z-Bracket MP Husky s Z-Bracket is recommended where you need to attach Husky Techtray to a rack, a wall, an enclosure, or to the floor. Hardware to fasten tray to bracket is included. Z-Bracket Part No. WB-Z Hardware Items Part No. Description B-5 1/4 x 20 x 5/8 Splice & Hold Down Bolt (Zinc plated) B-18 1/4 x 20 x 1-1/4 Hold Down Bolt (Zinc plated) B-18-6S 1/4 x 20 x 1-1/4 316 Stainless Steel Bolt B-19 3/8 x 16 x 3/4 Hold Down Bolt for WBHDC-3/8 Zinc N-2 1/4 x 20 Keps Nut for Splice, 1/4 Hanger Rod & Hold Down (Zinc plated) N-2-6S 1/4 x 20 Keps Nut for Splice, 1/4 Hanger Rod & Hold Down (316 Stainless) N-52 3/8 x 16 Hex Nut for WBHDC-3/8 or 3/8 Hanger Rod W-13 1/4 x 3/4 Flat Washers (Zinc plated) W-13-6S 1/4 x 3/4 Flat Washers (316 Stainless) W-24 3/8 x 13/16 Flat Washer (316 Stainless) HR-1/4-144G 1/4 x 12 Long Hanger Rod Continuously Threaded Zinc Plated HR-3/8-144G 3/8 x 12 Long Hanger Rod Continuously Threaded Zinc Plated Cutting Tool For cutting wire when forming fittings or cutting straights to size in the field. The cutter is equipped with offset blades for close cutting next to perpendicular wiresto prevent projections. Handles are 17 long. Cutting Tool Part No. WBCT 189