Features. R TOTAL (k ) TEMP. RANGE ( C)
|
|
- Emil Shaw
- 6 years ago
- Views:
Transcription
1 DATASHEET ISL35 Single Push Button Controlled Potentiometer (XDCP ) Low Noise, Low Power, 3 Taps, Push Button Controlled Potentiometer FN588 Rev. The Intersil ISL35 is a three-terminal digitally-controlled potentiometer (XDCP) implemented by a resistor array composed of 3 resistive elements and a wiper switching network. The ISL35 features a push button control, a shutdown mode, as well as an industry-leading µtqfn package. The push button control has individual and inputs for adjusting the wiper. To eliminate redundancy, the wiper position will automatically increment or decrement if one of these inputs is held longer than s. Forcing both and low for more than s activates shutdown mode. Shutdown mode disconnects the top of the resistor chain and moves the wiper to the lowest position, minimizing power consumption. The three terminals accessing the resistor chain naturally configure the ISL35 as a voltage divider. A rheostat is easily formed by floating an end terminal or connecting it to the wiper. V CC (SUPPLY VOLTAGE) CONTROL BLOCK V SS (GROUND) V SS O µtfqfn 9 8 V CC (TOP VIEW) 3 7 V SS 4 5 NO LONGER AVAILABLE OR SUPPORTED O SOIC (TOP VIEW) 4 5 V CC Features Solid-state volatile potentiometer Push button controlled Single or Auto increment/decrement - Fast Mode after s button press Shutdown Mode 3 wiper tap points - Zero scale wiper position on power-up Low power CMOS - to 5.5V - Terminal voltage, to V CC - Standby current, 3µA max R TOTAL value = k 5k Packages - 8 Ld SOIC and Ld µtqfn (.mmx.mm) Pb-free (RoHS compliant) Applications Volume Control LED/LCD Brightness Control Contrast Control Programming Bias Voltages Ladder Networks Ordering Information PART NUMBER PART MARKING R TOTAL (k ) TEMP. RANGE ( C) PACKAGE (Pb-free) PKG. DWG. # ISL35WFB8Z* (Note ) 35 WFBZ -4 to +5 8 Ld SOIC M8.5 ISL35WFRUZ-TK (Note ) (No longer available or supported) GA -4 to +5 Ld µtqfn L..x.A *Add -TK suffix for tape and reel. Please refer to TB347 for details on reel specifications. NOTES:. These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and % matte tin plate PLUS ANNEAL - e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-.. These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and NiPdAu plate - e4 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-. FN588 Rev. Page of
2 Pinouts V SS O 3 4 ISL35 (8 LD SOIC) TOP VIEW V CC V SS ISL35 ( LD ΜTQFN) TOP VIEW O V CC NO LONGER AVAILABLE OR SUPPORTED Pin Descriptions SOIC PIN µtqfn PIN SYMBOL BRIEF DESCRIPTION The is a negative-edge triggered input with internal pull-up. Toggling will move the wiper close to terminal. The is a negative-edge triggered input with internal pull-up. Toggling will move the wiper close to terminal. 3 3 The and pins of the ISL35 are equivalent to the fixed terminals of a mechanical potentiometer. The minimum voltage is VSS and the maximum is V CC. The terminology of and RL references the relative position of the terminal in relation to wiper movement direction selected by the / input. 4 4 V SS Ground 5 The pin is the wiper terminal of the potentiometer, which is equivalent to the movable terminal of a mechanical potentiometer. 7 The and pins of the ISL35 are equivalent to the fixed terminals of a mechanical potentiometer. The minimum voltage is VSS and the maximum is V CC. The terminology of and references the relative position of the terminal in relation to wiper movement direction selected by the / input. 7 5, 8, No connection 8 9 V CC Supply Voltage Block Diagrams V CC (SUPPLY VOLTAGE) 5-BIT UP/DOWN COUNTER CONTROL BLOCK ONE 8 OF THIRTY TWO DECODER TRANSFER GATES RESISTOR ARRAY V SS (GROUND) GENERAL DETAILED FN588 Rev. Page of
3 Absolute Maximum Ratings Storage Temperature C to +5 C Voltage at and Pin with Respect to GND. -.3V to V CC +.3 V CC V to +V Voltage at any DCP Pin with Respect to GND V to V CC I W (s) ±ma Latchup Class II, Level +5 C ESD Rating Human Body Model kV Machine Model V Thermal Information Thermal Resistance (Typical, Note 3, 4) JA ( C/W) JC ( C/W) 8 Lead SOIC Lead µtqfn Maximum Junction Temperature (Plastic Package) C Pb-free Reflow Profile see link below Recommended Operating Conditions Temperature Range (Extended Industrial) C to +5 C V CC V to 5.5V Power Rating mW Wiper Current ±3.mA CAUTION: Do not operate at or near the maximum ratings listed for extended periods of time. Exposure to such conditions may adversely impact product reliability and result in failures not covered by warranty. NOTES: 3. JA is measured with the component mounted on a high effective thermal conductivity test board in free air. See Tech Brief TB379 for details. 4. For JC, the case temp location is the center of the exposed metal pad on the package underside. Potentiometer Specifications Over recommended operating conditions, unless otherwise specified. SYMBOL PARAMETER TEST CONDITIONS MIN (Note 8) TYP (Note 5) MAX (Note 8) UNIT R TOTAL to Resistance W option k U option 5 k to Resistance Tolerance - + % End-to-End Temperature Coefficient W option ±8 ppm/ C (Note ) U option ±5 ppm/ C (Note ) Wiper Resistance V CC = 3.3V, wiper current I RW = V CC /R TOTAL 3 4 V RH, V RL V RH and V RL Terminal Voltages V RH and V RL to GND V CC V Noise on Wiper Terminal From Hz to MHz -8 dbv C H /C L /C W (Note 7) Potentiometer Capacitance //5 pf I LkgDCP Leakage on DCP Pins Voltage at pin from GND to V CC.5.4 µa VOLTAGE DIVIDER MODE ; V ; measured at unloaded) INL (Note ) DNL (Note 9) ZSerror (Note 7) FSerror (Note 8) TC V (Note ) Integral Non-linearity - LSB (Note ) Differential Non-linearity Monotonic over all tap positions LSB (Note ) Zero-scale Error W option.3 3 LSB U option.3 (Note ) Full-scale Error W option LSB U option (Note ) Ratiometric Temperature Coefficient Wiper from 5 hex to F hex for W and U option ±5 ppm/ C f CUTOFF 3dB Cut-Off Frequency Wiper at the middle scale, W option 5 khz Wiper at the middle scale, U option 75 khz RESISTOR MODE (Measurements between and with not connected, or between and with not connected) RINL (Note 5) Integral Non-linearity DCP register set between hex and F hex; monotonic over all tap positions; W option DCP register set between hex and F hex; monotonic over all tap positions; U option MI (Note ) - MI (Note ) FN588 Rev. Page 3 of
4 Potentiometer Specifications RDNL (Note 4) Roffset (Note 3) Over recommended operating conditions, unless otherwise specified. (Continued) SYMBOL PARAMETER TEST CONDITIONS MIN (Note 8) TYP (Note 5) MAX (Note 8) Differential Non-linearity W and U option MI (Note ) Offset W option 3 MI (Note ) U option.5 MI (Note ) DC Electrical Specifications Over recommended operating conditions unless otherwise specified. SYMBOL PARAMETER TEST CONDITIONS I CC V CC Active Current, perform wiper move operation MIN (Note 8) TYP (Note 5) MAX (Note 8) UNIT UNIT 5 µa I SB Standby Current. 3 µa I Lkg, Input Leakage Current V IN = V SS to V CC - + µa V IH, Input HIGH Voltage V CC x.7 V V IL, input LOW Voltage V CC x. V C IN (Note 7), Input Capacitance V CC = 3.3V, T A = +5 C, f = MHz pf Rpull_up (Note 7) Pull-up Resistor for and M AC Electrical Specifications Over recommended operating conditions unless otherwise specified. SYMBOL PARAMETER MIN (Note 8) TYP (Note 5) MAX (Note 8) UNIT t GAP Time Between Two Separate Push Button Events ms t DB Debounce Time 5 3 ms t S SLOW Wiper Change on a Slow Mode ms t S FAST Wiper Change on a Fast Mode ms t stdn (Note 7) Time to Enter Shutdown Mode (keep and LOW) s t R VCC V CC Power-up Rate. 5 V/ms NOTES: 5. Typical values are for T A = +5 C and 3.3V supply voltage.. LSB: [V(RW) 3 V(RW) ]/3. V(RW) 3 and V(RW) are voltage on RW pin for the DCP register set to F hex and hex respectively. LSB is the incremental voltage when changing from one tap to an adjacent tap. 7. ZS error = V(RW) /LSB. 8. FS error = [V(RW) 3 V CC ]/LSB. 9. DNL = [V(RW) i V(RW) i- ]/LSB -, for i = to 3; i is the DCP register setting.. INL = [V(RW) i i LSB V(RW)]/LSB for i = to 3 Max V RW. i Min V RW i TC for i = 5 to 3 decimal, T = -4 C to +5 C. Max( ) is the maximum value of the wiper V = Max V RW i + Min V RW i +5 Cvoltage and Min ( ) is the minimum value of the wiper voltage over the temperature range.. MI = RW 3 RW /3. MI is a minimum increment. RW 3 and RW are the measured resistances for the DCP register set to F hex and hex respectively. 3. Roffset = RW /MI, when measuring between RW and RL. Roffset = RW 3 /MI, when measuring between RW and RH. 4. RDNL = (RW i RW i- )/MI, for i = to RINL = [RW i (MI i) RW ]/MI, for i = to 3.. Max Ri Min Ri for i = 5 to 3, T = -4 C to +5 C. Max( ) is the maximum value of the resistance and Min ( ) is TC R = Max Ri + Min Ri +5 Cthe minimum value of the resistance over the temperature range. 7. Limits should be considered typical and are not production tested. 8. Parts are % tested at +5 C. Over-temperature limits established by characterization and are not production tested. FN588 Rev. Page 4 of
5 Slow Mode Timing t DB t GAP MI * V W * MI in the AC timing diagram refers to the minimum incremental change in the wiper voltage. Fast Mode Timing t DB t S FAST t S SLOW V W MI * s * MI in the AC timing diagram refers to the minimum incremental change in the wiper voltage. Shutdown Mode Timing t DB s SHUTDOWN MODE V W FN588 Rev. Page 5 of
6 Typical Performance Curves WIPER RESISTAE ( ) ºC +5ºC -4ºC I CC (µa) FIGURE. WIPER RESISTAE vs TAP POSITION [ I(RW) = V CC /R TOTAL ] FOR k (W) TEMPERATURE ( C) FIGURE. STANDBY I CC vs TEMPERATURE DNL (LSB) FIGURE 3. DNL vs TAP POSITION IN VOLTAGE DIVIDER MODE FOR k (W) INL (LSB) FIGURE 4. INL vs TAP POSITION IN VOLTAGE DIVIDER MODE FOR k (W). ZERO SCALE ERROR (LSB) FULL SCALE ERROR (LSB) TEMPERATURE ( C) FIGURE 5. ZS ERROR vs TEMPERATURE TEMPERATURE ( C) FIGURE. FS ERROR vs TEMPERATURE FN588 Rev. Page of
7 Typical Performance Curves (Continued)..8.. RDNL (LSB). -. RINL (LSB) FIGURE 7. DNL vs TAP POSITION IN RHEOSTAT MODE FOR k (W) FIGURE 8. INL vs TAP POSITION IN RHEOSTAT MODE FOR k (W) R TOTAL CHANGE (%) k TCv (ppm/ C) k 5k 5k TEMPERATURE ( C) FIGURE 9. END-TO-END R TOTAL % CHANGE vs TEMPERATURE FIGURE. TC FOR VOLTAGE DIVIDER MODE IN ppm INT SINEWAVE 3 5 TCr (ppm/ C) 5 5 5k k 3dB CUTOFF = 5kHz MIDSCALE OUTT FIGURE. TC FOR RHEOSTAT MODE IN ppm FIGURE. FREQUEY RESPONSE (5kHz) FN588 Rev. Page 7 of
8 Power-up and Power-down Requirements There are no restrictions on the power-up or power-down conditions of V CC and the voltages applied to the potentiometer pins provided that V CC is always more positive than or equal to V RH and V RL, i.e., V CC V RH, V RL. The V CC ramp rate specification is always in effect. Pin Descriptions and The and pins of the ISL35 are equivalent to the fixed terminals of a mechanical potentiometer. The minimum voltage is V SS and the maximum is V CC. The terminology of and references the relative position of the terminal in relation to wiper movement direction. The pin is the wiper terminal of the potentiometer which is equivalent to the movable terminal of a mechanical potentiometer. The default wiper position at power-up is at tap. The debounced input is used to increment the wiper position. An on-chip pull-up holds the input HIGH. A switch closure to ground or a LOW logic level will, after a debounce time, move the wiper to the next adjacent higher tap position. The debounced input is used to decrement the wiper position. An on-chip pull-up holds the input HIGH. A switch closure to ground or a LOW logic level will, after a debounce time, move the wiper to the next adjacent lower tap position. Device Operation There are three sections of the ISL35: the input control, the counter and decode section and the resistor array. The input control section operates just like an up/down counter. The output of this counter is decoded to turn on a single electronic switch, connecting a point on the resistor array to the wiper output. The resistor array is comprised of 3 individual resistors connected in series. At either end of the array and between each resistor is an electronic switch that transfers the potential at that point to the wiper. The ISL35 is designed to interface directly to two push button switches for effectively moving the wiper up or down. The and inputs increment or decrement a 5-bit counter respectively. The output of this counter is decoded to select one of the thirty-two wiper positions along the resistive array. The wiper increment input, and the wiper decrement input, are both connected to an internal pull-up so that they normally remain HIGH. When pulled LOW by an external push button switch or a logic LOW level input, the wiper will be switched to the next adjacent tap position. Internal debounce circuitry prevents inadvertent switching of the wiper position if or remain LOW for less than 5ms, typical. Each of the buttons can be pushed either once for a single increment/decrement or continuously for a multiple increments/decrements. The number of increments/decrements of the wiper position depend on how long the button is being pushed. When making a continuous push, after the first second, the increment/decrement speed increases. For the first second, the device will be in the slow scan mode. Then, if the button is held for longer than s, the device will go into the fast scan mode. As soon as the button is released, the ISL35 will return to a stand-by condition. If both and buttons are pulled low more than 5ms from each other, all commands are ignored upon release of ALL buttons. The wiper, when at either fixed terminal, acts like its mechanical equivalent and does not move beyond the last position. That is, the counter does not wrap around when clocked to either extreme. Shutdown Mode The ISL35 enters into Shutdown Mode if both and inputs are kept LOW for s. In this mode, the resistors array is totally disconnected from its pin and the wiper is moved to the position closest to the pin, as shown in Figure 3. FIGURE 3. DCP CONNECTION IN SHUTDOWN MODE Note that and inputs must be brought LOW within t DB time window of 5ms (see Shutdown Mode Timing on page 5) otherwise all commands will be ignored until both inputs are released. Holding either or input LOW for more than 5ms will exit shutdown mode and return wiper to prior shutdown position. If or will be held LOW for more than 5ms, the ISL35 will start auto-increment or auto-decrement of wiper position. R TOTAL with V CC Removed The end-to-end resistance of the array will fluctuate once V CC is removed. FN588 Rev. Page 8 of
9 Revision History The revision history provided is for informational purposes only and is believed to be accurate, but not warranted. Please go to the web to make sure that you have the latest revision. DATE REVISION CHANGE FN Ordering Information Table on page. - Added Revision History. - Added About Intersil Verbiage. -Updated POD M8.5 to most current revision with changes as follows: -Revision to Revision Changes: Updated to new POD format by removing table and moving dimensions onto drawing and adding land pattern -Revision to Revision 3 Changes: Changed in Typical Recommended Land Pattern the following:.4(.95) to.(.87).7 (.3) to.(.3). to 5.(.5) -Revision 3 to Revision 4 Changes: Changed Note "98" to "994" About Intersil Intersil Corporation is a leading provider of innovative power management and precision analog solutions. The company's products address some of the largest markets within the industrial and infrastructure, mobile computing and high-end consumer markets. For the most updated datasheet, application notes, related documentation and related parts, please see the respective product information page found at You may report errors or suggestions for improving this datasheet by visiting Reliability reports are also available from our website at Copyright Intersil Americas LLC 7-5. All Rights Reserved. All trademarks and registered trademarks are the property of their respective owners. For additional products, see Intersil products are manufactured, assembled and tested utilizing ISO9 quality systems as noted in the quality certifications found at Intersil products are sold by description only. Intersil may modify the circuit design and/or specifications of products at any time without notice, provided that such modification does not, in Intersil's sole judgment, affect the form, fit or function of the product. Accordingly, the reader is cautioned to verify that datasheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see FN588 Rev. Page 9 of
10 Ultra Thin Quad Flat No-Lead Plastic Package (UTQFN) NX (b) 5 INDEX AREA X PIN # ID X. C. C.5 C SEATING PLANE (DATUM A) N SECTION "C-C" N- N. C (A) A e A D TOP VIEW SIDE VIEW 3 (ND-) X e NX L BOTTOM VIEW C C e C L NX b 5 A (DATUM B) B E 4xk. M C A B.5 M C FOR ODD TERMINAL/SIDE b L C TERMINAL TIP L..x.A LEAD ULTRA THIN QUAD FLAT NO-LEAD PLASTIC PACKAGE SYMBOL MILLIMETERS MIN NOMINAL MAX NOTES A A A3.7 REF - b D E e.5 BSC - k L N Nd 4 3 Ne 3-4 Rev. 3 / NOTES:. Dimensioning and tolerancing conform to ASME Y N is the number of terminals. 3. Nd and Ne refer to the number of terminals on D and E side, respectively. 4. All dimensions are in millimeters. Angles are in degrees. 5. Dimension b applies to the metallized terminal and is measured between.5mm and.3mm from the terminal tip.. The configuration of the pin # identifier is optional, but must be located within the zone indicated. The pin # identifier may be either a mold or mark feature. 7. Maximum package warpage is.5mm. 8. Maximum allowable burrs is.7mm in all directions. 9. Same as JEDEC MO-55UABD except: No lead-pull-back, "A" MIN dimension =.45 not.5mm "L" MAX dimension =.45 not.4mm.. For additional information, to assist with the PCB Land Pattern Design effort, see Intersil Technical Brief TB MIN L MIN DETAIL A PIN ID.5.5 LAND PATTERN FN588 Rev. Page of
11 Package Outline Drawing M8.5 8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE Rev 4, / DETAIL "A".7 (.5).4 (.) INDEX AREA 4. (.57) 3.8 (.5). (.44) 5.8 (.8).5 (.).5 (.) x 45 3 TOP VIEW 8 SIDE VIEW B.5 (.).9 (.8). (.87) SEATING PLANE 8 5. (.97) 4.8 (.89).75 (.9).35 (.53) 7. (.3).7 (.5) 3 -C-.7 (.5).5(.).33(.3).5(.).(.4) (.5) SIDE VIEW A TYPICAL RECOMMENDED LAND PATTERN NOTES:. Dimensioning and tolerancing per ANSI Y4.5M Package length does not include mold flash, protrusions or gate burrs. Mold flash, protrusion and gate burrs shall not exceed.5mm (. inch) per side. 3. Package width does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed.5mm (. inch) per side. 4. The chamfer on the body is optional. If it is not present, a visual index feature must be located within the crosshatched area. 5. Terminal numbers are shown for reference only.. The lead width as measured.3mm (.4 inch) or greater above the seating plane, shall not exceed a maximum value of.mm (.4 inch). 7. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily exact. 8. This outline conforms to JEDEC publication MS--AA ISSUE C. FN588 Rev. Page of
DATASHEET ISL Features. Applications
DATASHEET ISL225 Single Push Button Controlled Potentiometer (XDCP ) Low Noise, Low Power, 32 Taps, Push Button Controlled Potentiometer FN78 Rev 2. The Intersil ISL225 is a three-terminal digitally-controlled
More informationDATASHEET ISL Features. Ordering Information. Pinout
NOT RECOMMENDED FOR NEW DESIGNS RECOMMENDED REPLACEMENT PART X9015 Volatile Digitally Controlled Potentiometer (XDCP ) Terminal Voltage ±3V or ±5V, 128 Taps Up/Down Interface DATASHEET FN6126 Rev 0.00
More informationDATASHEET X9511. Single Push Button Controlled Potentiometer (XDCP ) Linear, 32 Taps, Push Button Controlled, Terminal Voltage ±5V
DATASHEET X95 Single Push Button Controlled Potentiometer (XDCP ) Linear, 32 Taps, Push Button Controlled, Terminal Voltage ±5V FN8205 Rev 3.00 FEATURES Push button controlled Low power CMOS Active current,
More informationDATASHEET X Features. Pinout. Ordering Information. Dual Digitally Controlled Potentiometers (XDCPs ) FN8187 Rev 1.
DATASHEET X93255 Dual Digitally Controlled Potentiometers (XDCPs ) The Intersil X93255 is a dual digitally controlled potentiometer (XDCP). The device consists of two resistor arrays, wiper switches, a
More informationDATASHEET ISL Features. Pinout. Ordering Information
ISL9571 NOT RECOMMENDED FOR NEW DESIGNS RECOMMENDED REPLACEMENT: ISL9531 Digitally Controlled Potentiometer (XDCP ), Terminal Voltage ±2.7V to ±5V, 128 Taps, Up/Down Interface DATASHEET FN824 Rev 3. The
More informationDATASHEET X Features. Pinout. Ordering Information. Dual Digitally Controlled Potentiometers (XDCPs ) FN8186 Rev 1.
DATASHEET X93254 Dual Digitally Controlled Potentiometers (XDCPs ) The Intersil X93254 is a dual digitally controlled potentiometer (XDCP). The device consists of two resistor arrays, wiper switches, a
More informationFeatures TEMP. RANGE ( C)
DATASHEET HFA0, HFA09, HFA27, HFA28 Ultra High Frequency Transistor Arrays The HFA0, HFA09, HFA27 and the HFA28 are Ultra High Frequency Transistor Arrays that are fabricated from Intersil Corporation
More informationDATASHEET X9015. Features. Pinout SOIC/MSOP. Block Diagram. Low Noise, Low Power, Volatile Single Digitally Controlled (XDCP ) Potentiometer
DATASHEET X9015 Low Noise, Low Power, Volatile Single Digitally Controlled (XDCP ) Potentiometer FN8157 Rev 6.00 The Intersil X9015 is a 32 tap potentiometer that is volatile. The device consists of a
More informationDATASHEET ISL Features. Audio Performance. Pinout. Applications
DATASHEET 32 Tap, Push-Button, Dual Audio Logarithmic Potentiometer with Buffer Amplifiers and Audio Detection FN6788 Rev 2.00 The integrates two digitally controlled potentiometers (DCP) with buffered
More informationDATASHEET ISL6700. Features. Ordering Information. Applications. Pinouts. 80V/1.25A Peak, Medium Frequency, Low Cost, Half-Bridge Driver
DATASHEET ISL6700 80V/1.25A Peak, Medium Frequency, Low Cost, Half-Bridge Driver FN9077 Rev.6.00 The ISL6700 is an 80V/1.25A peak, medium frequency, low cost, half-bridge driver IC available in 8-lead
More informationDATASHEET X9318. Digitally Controlled Potentiometer (XDCP )
DATASHEET X9318 Digitally Controlled Potentiometer (XDCP ) FN8184 Rev 1.00 FEATURES Solid-state potentiometer 3-wire serial interface Terminal voltage, 0 to +8V 100 wiper tap points Wiper position stored
More informationDATASHEET. Features. Applications ISL Single, Low Voltage Digitally Controlled Potentiometer (XDCP ) FN7780 Rev 2.
DATASHEET ISL23415 Single, Low Voltage Digitally Controlled Potentiometer (XDCP ) FN778 Rev 2. The ISL23415 is a volatile, low voltage, low noise, low power, SPI bus, 256 taps, single digitally controlled
More informationISL22446 Quad Digitally Controlled Potentiometer (XDCP )
ISL22446 Quad Digitally Controlled Potentiometer (XDCP ) Data Sheet FN6181.2 Low Noise, Low Power, SPI Bus, 128 Taps The ISL22446 integrates four digitally controlled potentiometers (DCP) and non-volatile
More informationFeatures 7-BIT UP/DOWN COUNTER V CC (SUPPLY VOLTAGE) 97 7-BIT NON-VOLATILE MEMORY 2 V SS (GROUND) STORE AND RECALL CONTROL CIRCUITRY
DATASHEET X9C102, X9C103, X9C104, X9C503 Digitally Controlled Potentiometer (XDCP ) The X9C102, X9C103, X9C104, X9C503 are Intersils digitally controlled (XDCP) potentiometers. The device consists of a
More informationSALLEN-KEY LOW PASS FILTER
DATASHEET ISL28325, ISL28345 40V Low Power Dual and Quad Operational Amplifier The ISL28325 and ISL28345 are dual and quad general purpose amplifiers featuring low noise vs power consumption. The combination
More informationDATASHEET CA3127. Features. Applications. Ordering Information. Pinout. High Frequency NPN Transistor Array. FN662 Rev.5.00 Page 1 of 9.
DATASHEET CA1 High Frequency NPN Transistor Array The CA1 consists of five general purpose silicon NPN transistors on a common monolithic substrate. Each of the completely isolated transistors exhibits
More informationDATASHEET ISL9005A. Features. Pinout. Applications. Ordering Information. LDO with Low ISUPPLY, High PSRR. FN6452 Rev 2.
DATASHEET ISL95A LDO with Low ISUPPLY, High PSRR FN6452 Rev 2. November 2, 215 ISL95A is a high performance Low Dropout linear regulator capable of sourcing 3mA current. It has a low standby current and
More informationDATASHEET ICL8069. Features. Pinouts. Ordering Information. Low Voltage Reference. FN3172 Rev.3.00 Page 1 of 6. Jan FN3172 Rev.3.00.
DATASHEET Low Voltage Reference The is a 1.2V temperature-compensated voltage reference. It uses the band-gap principle to achieve excellent stability and low noise at reverse currents down to 50 A. Applications
More informationDATASHEET X9C303. Description. Features. Block Diagram
DATASHEET X9C303 Logarithmic Digitally Controlled Potentiometer (XDCP ) Terminal Voltage ±5V, 100 Taps, Log Taper FN8223 Rev 2.00 Description The Intersil X9C303 is a digitally controlled potentiometer
More informationDATASHEET ISL Features. Applications. Simplified Block Diagram. Pinout. Ordering Information. Pin Descriptions
DATASHEET ISL99 Non-Linear Output Current, Low Power Ambient Light Photo Detect IC FN8 Rev. The ISL99 is a light-to-current silicon optical sensor combining a photodiode and current amplifiers on a single
More informationDATASHEET ISL9021A. Features. Pinouts. Applications. 250mA Single LDO with Low I Q, Low Noise and High PSRR LDO. FN6867 Rev 2.
NOT RECOMMENDED FOR NEW DESIGNS RECOMMENDED REPLACEMENT PART ISL9021A 250mA Single LDO with Low I Q, Low Noise and High PSRR LDO DATASHEET FN6867 Rev 2.00 The ISL9021 is a single LDO providing high performance
More informationDATASHEET ISL Features. Pinout. Single Digitally Controlled Potentiometer (XDCP ) Low Noise, Low Power, SPI Bus, 256 Taps
NOT RECOMMENDED FOR NEW DESIGNS NO RECOMMENDED REPLACEMENT contact our Technical Support Center at 1-888-INTERSIL or www.intersil.com/tsc Single Digitally Controlled Potentiometer (XDCP ) Low Noise, Low
More informationDATASHEET CA Applications. Pinout. Ordering Information. General Purpose NPN Transistor Array. FN483 Rev.6.00 Page 1 of 7.
DATASHEET CA-386 General Purpose NPN Transistor Array The CA386 consists of five general-purpose silicon NPN transistors on a common monolithic substrate. Two of the transistors are internally connected
More informationDATASHEET. Features. Applications. Related Literature ISL V, Low Quiescent Current, 50mA Linear Regulator. FN7970 Rev 2.
DATASHEET ISL8136 4V, Low Quiescent Current, 5mA Linear Regulator The ISL8136 is a high voltage, low quiescent current linear regulator ideally suited for always-on and keep alive applications. The ISL8136
More informationDATASHEET HC5503T. Features. Applications. Ordering Information. Block Diagram. Balanced PBX/Key System SLIC, Subscriber Line Interface Circuit
NOT RECOMMENDED FOR NEW DESIGNS RECOMMENDED REPLACEMENT PART HC5503PRC Balanced PBX/Key System SLIC, Subscriber Line Interface Circuit DATASHEET FN4506 Rev 2.00 The Intersil HC5503T is a low cost Subscriber
More informationFeatures V OUT = 12V IN TEMPERATURE ( C) FIGURE 3. QUIESCENT CURRENT vs LOAD CURRENT (ADJ VERSION AT UNITY GAIN) V IN = 14V
DATASHEET ISL7831 4V, Low Quiescent Current, 15mA Linear Regulator for Automotive Applications FN675 Rev 2. The ISL7831 is a high voltage, low quiescent current linear regulator ideally suited for always-on
More informationX9C102, X9C103, X9C104, X9C503
X9C102, X9C103, X9C104, X9C503 Data Sheet FN8222.1 Digitally Controlled Potentiometer (XDCP ) FEATURES Solid-state potentiometer 3-wire serial interface 100 wiper tap points Wiper position stored in nonvolatile
More informationFeatures. TEMP. RANGE ( C) PACKAGE PKG. DWG. # HIP4020IB (No longer available, recommended replacement: HIP4020IBZ)
DATASHEET Half Amp Full Bridge Power Driver for Small 3V, 5V and 12V DC Motors FN3976 Rev 4.00 In the Functional Block Diagram of the, the four switches and a load are arranged in an H-Configuration so
More informationDATASHEET HI-200, HI-201. Features. Applications. Ordering Information. Functional Diagram. Dual/Quad SPST, CMOS Analog Switches
DATASHEET HI-200, HI-201 Dual/Quad SPST, CMOS Analog Switches HI-200/HI-201 (dual/quad) are monolithic devices comprising independently selectable SPST switches which feature fast switching speeds (HI-200
More informationDATASHEET HA Features. Applications. Ordering Information. 110MHz, High Slew Rate, High Output Current Buffer. FN2921 Rev 12.
DATASHEET HA-52 MHz, High Slew Rate, High Output Current Buffer The HA-52 is a monolithic, wideband, high slew rate, high output current, buffer amplifier. Utilizing the advantages of the Intersil D.I.
More informationX9C102, X9C103, X9C104, X9C503
X9C102, X9C103, X9C104, X9C503 Data Sheet FN8222.1 Digitally Controlled Potentiometer (XDCP ) FEATURES Solid-state potentiometer 3-wire serial interface 100 wiper tap points Wiper position stored in nonvolatile
More informationDATASHEET EL7104. Features. Ordering Information. Applications. Pinout. High Speed, Single Channel, Power MOSFET Driver. FN7113 Rev 2.
DATASHEET EL7104 High Speed, Single Channel, Power MOSFET Driver FN7113 Rev 2.00 The EL7104 is a matched driver IC that improves the operation of the industry-standard TC-4420/29 clock drivers. The Elantec
More informationDATASHEET ISL Features. Applications. Ordering Information. Typical Application Circuit. MMIC Silicon Bipolar Broadband Amplifier.
ISL55 MMIC Silicon Bipolar Broadband Amplifier NOT RECOMMENDED FOR NEW DESIGNS NO RECOMMENDED REPLACEMENT contact our Technical Support Center at 1-888-INTERSIL or www.intersil.com/tsc DATASHEET FN17 Rev.
More informationDATASHEET ISL6208. Features. Applications. Related Literature. Ordering Information. Pinout. High Voltage Synchronous Rectified Buck MOSFET Driver
NOT RECOMMENDED FOR NEW DESIGNS POSSIBLE SUBSTITUTE PRODUCT ISL6208 High Voltage Synchronous Rectified Buck MOSFET Driver DATASHEET FN9047 Rev 0.00 The ISL6205 is a high-voltage, high-frequency, dual MOSFET
More informationDATASHEET. Features. Applications X9317. Low Noise, Low Power, 100 Taps, Digitally Controlled Potentiometer (XDCP ) FN8183 Rev 9.
DATASHEET X9317 Low Noise, Low Power, 100 Taps, Digitally Controlled Potentiometer (XDCP ) FN8183 Rev 9.00 The Intersil X9317 is a digitally controlled potentiometer (XDCP ). The device consists of a resistor
More informationISL6536A. Four Channel Supervisory IC. Features. Applications. Typical Application Schematic. Ordering Information. Data Sheet May 2004 FN9136.
ISL6536A Data Sheet May 2004 FN9136.1 Four Channel Supervisory IC The ISL6536A is a four channel supervisory IC designed to monitor voltages >, = 0.7V. This IC bias range is from 2.7V to 5V but can supervise
More informationDATASHEET CD22M3494. Features. Applications. Block Diagram. 16 x 8 x 1 BiMOS-E Crosspoint Switch. FN2793 Rev 8.00 Page 1 of 10.
DATASHEET CD22M3494 16 x 8 x 1 BiMOS-E Crosspoint Switch The Intersil CD22M3494 is an array of 128 analog switches capable of handling signals from DC to video. Because of the switch structure, input signals
More informationDATASHEET. Features. Applications ISL mA Dual LDO with Low Noise, High PSRR, and Low I Q. FN6832 Rev 1.00 Page 1 of 11.
DATASHEET ISL9016 150mA Dual LDO with Low Noise, High PSRR, and Low I Q FN6832 Rev 1.00 ISL9016 is a high performance dual LDO capable of providing up to 150mA current on each channel. It features a low
More informationDATASHEET ISL Features. Dual Digitally Controlled Potentiometer (XDCP ) Low Noise, Low Power, SPI Bus, 256 Taps. FN6425 Rev 1.
DATASHEET ISL22424 Dual Digitally Controlled Potentiometer (XDCP ) Low Noise, Low Power, SPI Bus, 256 Taps FN6425 Rev 1.00 The ISL22424 integrates two digitally controlled potentiometers (DCP), control
More informationDATASHEET HFA3102. Features. Ordering Information. Applications. Pinout/Functional Diagram. Dual Long-Tailed Pair Transistor Array
DATASHEET HFA312 Dual Long-Tailed Pair Transistor Array The HFA312 is an all NPN transistor array configured as dual differential amplifiers with tail transistors. Based on Intersil bonded wafer UHF-1
More informationNOT RECOMMENDED FOR NEW DESIGNS
NOT RECOMMENDED FOR NEW DESIGNS POSSIBLE SUBSTITUTE PRODUCTS (ISL6614, ISL6614A, and ISL6614B) Dual Channel Synchronous-Rectified Buck MOSFET Driver DATASHEET FN4838 Rev.1. The HIP662 is a high frequency,
More informationDATASHEET. Features. Applications ISL Quad, 128 Tap, Low Voltage Digitally Controlled Potentiometer (XDCP )
NOT RECOMMENDED FOR NEW DESIGNS RECOMMENDED REPLACEMENT PART ISL23428 Quad, 128 Tap, Low Voltage Digitally Controlled Potentiometer (XDCP ) DATASHEET FN795 Rev. The ISL23448 is a volatile, low voltage,
More informationDATASHEET EL8108. Features. Applications. Pinouts. Video Distribution Amplifier. FN7417 Rev 2.00 Page 1 of 14. January 29, FN7417 Rev 2.
EL Video Distribution Amplifier OBSOLETE PRODUCT NO RECOMMENDED REPLACEMENT contact our Technical Support Center at --INTERSIL or www.intersil.com/tsc DATASHEET FN77 Rev. The EL is a dual current feedback
More informationDATASHEET ISL Features. Ordering Information. Quad Digitally Controlled Potentiometer (XDCP ) Low Noise, Low Power, SPI Bus, 256 Taps
NOT RECOMMENDED FOR NEW DESIGNS RECOMMENDED REPLACEMENT PART ISL22424 Quad Digitally Controlled Potentiometer (XDCP ) Low Noise, Low Power, SPI Bus, 256 Taps DATASHEET FN6426 Rev. The integrates four digitally
More informationDATASHEET. Features. Related Literature. Applications ISL9021A. 250mA Single LDO with Low I Q, Low Noise and High PSRR LDO
DATASHEET ISL9021A 250mA Single LDO with Low I Q, Low Noise and High PSRR LDO FN7845 Rev 3.00 The ISL9021A is a single LDO, which provides high performance, low input voltage and high PSRR. It delivers
More informationDATASHEET ISL54409, ISL Features. Applications*(see page 11) Related Literature* (see page 11)
DATASHEET ISL54409, ISL54410 Audio/USB 2.0 Wired-OR Switch with Click and Pop Reduction FN6983 Rev 1.00 The Intersil ISL54409 and ISL54410 are Dual SPST (Single Pole/Single Throw) switches that provide
More informationHIP6601B, HIP6603B, HIP6604B
NOT RECOMMENDED FOR NEW DESIGNS NO RECOMMENDED REPLACEMENT contact our Technical Support Center at 1-888-INTERSIL or www.intersil.com/tsc Synchronous Rectified Buck MOSFET Drivers The HIP6601B, HIP6603B
More informationDATASHEET HA-2520, HA-2522, HA Features. Applications. Ordering Information
DATASHEET 2MHz, High Slew Rate, Uncompensated, High Input Impedance, Operational Amplifiers FN2894 Rev 1. comprise a series of operational amplifiers delivering an unsurpassed combination of specifications
More informationDATASHEET HFA1112. Features. Applications. Related Literature. Pin Descriptions. Ordering Information
DATASHEET HFA1112 85MHz, Low Distortion Programmable Gain Buffer Amplifiers FN2992 Rev 8. July 27, 25 The HFA1112 is a closed loop Buffer featuring user programmable gain and ultra high speed performance.
More informationDATASHEET HIP2101. Features. Ordering Information. Applications. 100V/2A Peak, Low Cost, High Frequency Half Bridge Driver
DATASHEET P20 00V/2A Peak, Low Cost, High Frequency Half Bridge Driver FN9025 Rev 9.00 The P20 is a high frequency, 00V Half Bridge N-Channel power MOSFET driver IC. It is equivalent to the P200 with the
More informationFeatures TEMP. RANGE ( C)
DATASHEET ISL57 Power Line Communication (PLC) The ISL57 is a dual operational amplifier designed for PLC line driving in OFDM and SSC based solutions. This device features a high drive capability of 750mA
More informationDATASHEET CA3054. Features. Applications. Ordering Information. Pinout. Dual Independent Differential Amp for Low Power Applications from DC to 120MHz
DATASHEET CA5 Dual Independent Differential Amp for Low Power Applications from DC to MHz FN88 Rev.. Jan, 7 The CA5 consists of two independent differential amplifiers with associated constant current
More informationFeatures OUTA OUTB OUTA OUTA OUTB OUTB
DATASHEET ISL89410, ISL89411, ISL89412 High Speed, Dual Channel Power MOSFET Drivers FN6798 Rev 2.00 The ISL89410, ISL89411, ISL89412 ICs are similar to the EL7202, EL7212, EL7222 series but with greater
More informationHA5023. Dual 125MHz Video Current Feedback Amplifier. Features. Applications. Ordering Information. Pinout. Data Sheet September 30, 2015 FN3393.
HA523 Data Sheet September 3, 215 FN3393.9 Dual 125MHz Video Current Feedback Amplifier The HA523 is a wide bandwidth high slew rate dual amplifier optimized for video applications and gains between 1
More informationDATASHEET EL7202, EL7212, EL7222. Features. Pinouts. Applications. High Speed, Dual Channel Power MOSFET Drivers. FN7282 Rev 2.
DATASHEET EL7202, EL7212, EL7222 High Speed, Dual Channel Power MOSFET Drivers FN7282 Rev 2.00 The EL7202, EL7212, EL7222 ICs are matched dual-drivers that improve the operation of the industry standard
More informationDATASHEET HA Features. Applications. Pinout. Ordering Information. Quad, 3.5MHz, Operational Amplifier. FN2922 Rev 5.00 Page 1 of 8.
DATASHEET HA-4741 Quad, 3.5MHz, Operational Amplifier HA-4741, which contains four amplifiers on a monolithic chip, provides a new measure of performance for general purpose operational amplifiers. Each
More informationNano Power, Push/Pull Output Comparator
Nano Power, Push/Pull Output Comparator ISL289 The ISL289 is a nano power comparator optimized for low-power applications. This device is designed for single-supply operation from.8v to.v and typically
More informationDATASHEET HA4314B. Features. Ordering Information. Applications. Truth Table. 400MHz, 4x1 Video Crosspoint Switch. FN3679 Rev 12.
DATASHEET B 4MHz, 4x1 Video Crosspoint Switch FN3679 Rev 12. The B is a very wide bandwidth 4x1 crosspoint switch ideal for professional video switching, HDTV, computer monitor routing, and other high
More informationTEMP. PKG. -IN 1 16 S/H CONTROL PART NUMBER RANGE
DATASHEET 7ns, Low Distortion, Precision Sample and Hold Amplifier FN59 Rev 5. The combines the advantages of two sample/ hold architectures to create a new generation of monolithic sample/hold. High amplitude,
More informationEnpirion Power Datasheet EY V, Low Quiescent Current, 50mA Linear Regulator
Enpirion Power Datasheet EY162 4V, Low Quiescent Current, 5mA Linear Regulator DS-146 Datasheet The Altera Enpirion EY162 is a wide input voltage range, low quiescent current linear regulator ideally suited
More informationDATASHEET HA Features. Applications. Ordering Information. Pinouts. 250MHz Video Buffer. FN2924 Rev 8.00 Page 1 of 12.
25MHz Video Buffer NOT RECOMMENDED FOR NEW DESIGNS NO RECOMMENDED REPLACEMENT contact our Technical Support Center at -888-INTERSIL or www.intersil.com/tsc DATASHEET FN2924 Rev 8. The HA-533 is a unity
More informationDATASHEET ISL6840, ISL6841, ISL6842, ISL6843, ISL6844, ISL6845. Features. Applications. Pinouts
DATASHEET ISL6840, ISL6841, ISL6842, ISL6843, ISL6844, ISL6845 Improved Industry Standard Single-Ended Current Mode PWM Controller FN9124 Rev 13.00 The ISL6840, ISL6841, ISL6842, ISL6843, ISL6844, ISL6845
More informationDATASHEET CA3096, CA3096A, CA3096C. Description. Applications. CA3096, CA3096A, CA3096C Essential Differences. Part Number Information.
DATASHEET CA39, CA39A, CA39C NPN/PNP Transistor Arrays Applications Five-Independent Transistors - Three NPN and - Two PNP Differential Amplifiers DC Amplifiers Sense Amplifiers Level Shifters Timers Lamp
More informationDATASHEET ISL Features. Applications Ordering Information. Pinouts. 5MHz, Single Precision Rail-to-Rail Input-Output (RRIO) Op Amp
DATASHEET ISL2836 MHz, Single Precision Rail-to-Rail Input-Output (RRIO) Op Amp FN63 Rev 6. January 6, 2 The ISL2836 is a low-power single operational amplifier optimized for single supply operation from
More informationHA-2520, HA-2522, HA-2525
HA-, HA-, HA- Data Sheet November, 6 FN894.8 MHz, High Slew Rate, Uncompensated, High Input Impedance, Operational Amplifiers HA-, HA-, HA- comprise a series of operational amplifiers delivering an unsurpassed
More informationDATASHEET ISL6207. Features. Applications. Related Literature. Pinouts. High Voltage Synchronous Rectified Buck MOSFET Driver
NOT RECOMMENDED FOR NEW DESIGNS NO RECOMMENDED REPLACEMENT contact our Technical Support Center at 1-888-INTERSIL or www.intersil.com/tsc High Voltage Synchronous Rectified Buck MOSFET Driver DATASHEET
More informationHIP V, 300mA Three Phase High Side Driver. Features. Applications. Ordering Information. Pinout. July 2004
HIP0 Data Sheet July 00 FN. 0V, 00mA Three Phase High Side Driver The HIP0 is a three phase high side N-channel MOSFET driver, specifically targeted for PWM motor control. Two HIP0 may be used together
More informationData Sheet September 3, Features TEMP. RANGE ( C)
Data Sheet FN6387. Power Line Communication (PLC) The ISL57 is a dual operational amplifier designed for PLC line driving in OFDM and SSC based solutions. This device features a high drive capability of
More informationDATASHEET ISL Features. Applications. Filterless High Efficiency 1.5W Class D Mono Amplifier
NOT RECOMMENDED FOR NEW DESIGNS NO RECOMMENDED REPLACEMENT contact our Technical Support Center at 888INTERSIL or www.intersil.com/tsc Filterless High Efficiency.5W Class D Mono Amplifier DATASHEET FN6742
More informationHI-200, HI-201. Dual/Quad SPST, CMOS Analog Switches. Features. Applications. Ordering Information. Functional Diagram FN3121.8
HI-200, HI-201 Data Sheet FN3121.8 Dual/Quad SPST, CMOS Analog Switches HI-200/HI-201 (dual/quad) are monolithic devices comprising independently selectable SPST switches which feature fast switching speeds
More informationDATASHEET ISL9001A. Features. Pinout. Applications. LDO with Low ISUPPLY, High PSRR. FN6433 Rev 3.00 Page 1 of 12. December 10, FN6433 Rev 3.
DATASHEET ISL91A LDO with Low ISUPPLY, High PSRR ISL91A is a high performance Low Dropout linear regulator capable of sourcing 3mA current. It has a low standby current and high-psrr and is stable with
More informationDATASHEET HI1171. Ordering Information. Typical Application Circuit. Pinout. 8-Bit, 40 MSPS, High Speed D/A Converter. FN3662 Rev.3.
-Bit, 40 MSPS, High Speed D/A Converter Pb-Free and RoHS Compliant DATASHEET FN366 Rev.3.00 Features Throughput Rate.......................... 40MHz Resolution.................................-Bit Integral
More informationEL2142. Features. Differential Line Receiver. Applications. Ordering Information. Pinout. Data Sheet February 11, 2005 FN7049.1
Data Sheet FN7049.1 Differential Line Receiver The is a very high bandwidth amplifier designed to extract the difference signal from noisy environments, and is thus primarily targeted for applications
More informationMARKING RANGE ( C) PACKAGE DWG. # HA-2600 (METAL CAN)
DATASHEET 2MHz, High Input Impedance Operational Amplifier is an internally compensated bipolar operational amplifier that features very high input impedance (5M coupled with wideband AC performance. The
More informationDATASHEET. Features. Applications. Related Literature ISL1550. Single Port, VDSL2 Differential Line Driver. FN6795 Rev 0.
DATASHEET ISL155 Single Port, VDSL2 Differential Line Driver The ISL155 is a dual operational amplifier intended to be used as a differential line driver. ISL155 s high bandwidth and low distortion performance
More informationDATASHEET ISL Features. Applications. Related Literature. Single Port, PLC Differential Line Driver
DATASHEET ISL112 Single Port, PLC Differential Line Driver FN8823 Rev.. The ISL112 is a single port differential line driver developed for Power Line Communication (PLC) applications. The device is designed
More informationDATASHEET HA Features. Applications. Pinout. Part Number Information. 12MHz, High Input Impedance, Operational Amplifier
12MHz, High Input Impedance, Operational Amplifier OBSOLETE PRODUCT POSSIBLE SUBSTITUTE PRODUCT HA-2525 DATASHEET FN289 Rev 6. HA-255 is an operational amplifier whose design is optimized to deliver excellent
More informationDATASHEET. Features. Ordering Information. Applications. Related Literature ISL28191, ISL28291
DATASHEET Single and Dual Single Supply Ultra-Low Noise, Low Distortion Rail-to-Rail Output, Op Amp FN656 Rev. The ISL89 and ISL89 are tiny single and dual ultra-low noise, ultra-low distortion operational
More informationFeatures. QUIESCENT CURRENT (µa)
Enpirion Power Datasheet EY161SA-ADJ 4V, Low Quiescent Current, 5mA Linear Regulator for EY161SA-ADJ Datasheet The EY161SA-ADJ is a high voltage, low quiescent current linear regulator ideally suited for
More informationDATASHEET ICL7611, ICL7612. Features. Applications. Pinouts. 1.4MHz, Low Power CMOS Operational Amplifiers. FN2919 Rev 9.
DATASHEET ICL711, ICL71 1.MHz, Low Power CMOS Operational Amplifiers The ICL71X series is a family of CMOS operational amplifiers. These devices provide the designer with high performance operation at
More informationDATASHEET. Features. Applications. Ordering Information. Related Literature ISL MHz, Dual Precision Rail-to-Rail Input-Output (RRIO) Op Amps
DATASHEET ISL28236 5MHz, Dual Precision Rail-to-Rail Input-Output (RRIO) Op Amps FN6921 Rev 2. July 24, 214 The ISL28236 is a low-power dual operational amplifier optimized for single supply operation
More informationDATASHEET ISL6209. Features. Applications. Ordering Information. Related Literature. High Voltage Synchronous Rectified Buck MOSFET Driver
DATASHEET ISL6209 High Voltage Synchronous Rectified Buck MOSFET Driver FN9132 Rev.2.00 The ISL6209 is a high frequency, dual MOSFET driver, optimized to drive two N-Channel power MOSFETs in a synchronous-rectified
More informationDATASHEET ISL9003A. Features. Pinouts. Applications. Low Noise LDO with Low I Q and High PSRR. FN6299 Rev 5.00 Page 1 of 12.
DATASHEET Low Noise LDO with Low I Q and High PSRR is a high performance single low noise, high PSRR LDO that delivers a continuous 15mA of load current. It has a low standby current and is stable with
More informationDATASHEET EL5127, EL5227, EL5327, EL5427. Features. Applications. 2.5MHz 4-, 8-, 10- and 12-Channel Rail-to-Rail Buffers. FN7111 Rev 4.
.5MHz -, 8-, - and -Channel Rail-to-Rail Buffers The EL57, EL57, EL57, and EL57 are low power, high voltage rail-to-rail input/output buffers designed for use in reference voltage buffering applications
More informationDATASHEET. Features. Applications. Pin Configurations EL8176. Micropower Single Supply Rail-to-Rail Input/Output Precision Op Amp
DATASHEET EL876 Micropower Single Supply Rail-to-Rail Input/Output Precision Op Amp FN76 Rev 9. January 6, 5 The EL876 is a precision low power, operational amplifier. The device is optimized for single
More informationDATASHEET HIP6602B. Features. Ordering Information. Applications. Dual Channel Synchronous Rectified Buck MOSFET Driver. FN9076 Rev 6.
NOT RECOMMENDED FOR NEW DESIGNS INTERSIL RECOMMENDS: ISL6612, ISL6612A, ISL6613, ISL6613A, ISL6614, ISL6614A, ISL6622, ISL6625A Dual Channel Synchronous Rectified Buck MOSFET Driver DATASHEET FN976 Rev
More informationCA3102. Dual High Frequency Differential Amplifier For Low Power Applications Up to 500MHz. Features. Applications. Ordering Information.
CA Data Sheet November 999 File Number 6.6 Dual High Frequency Differential Amplifier For Low Power Applications Up to MHz The CA consists of two independent differential amplifiers with associated constant
More informationDATASHEET DG408, DG409. Features. Applications. Ordering Information. Single 8-Channel/Differential 4-Channel, CMOS Analog Multiplexers
ATASHEET G48, G49 Single 8-Channel/ifferential 4-Channel, CMOS Analog Multiplexers FN3283 Rev 8. The G48 Single 8-Channel, and G49 ifferential 4-Channel monolithic CMOS analog multiplexers are drop-in
More informationCD22M x 8 x 1 BiMOS-E Crosspoint Switch. Features. Applications. Block Diagram FN Data Sheet January 16, 2006
CD22M3494 Data Sheet FN2793.7 6 x 8 x BiMOS-E Crosspoint Switch The Intersil CD22M3494 is an array of 28 analog switches capable of handling signals from DC to video. Because of the switch structure, input
More informationDATASHEET ICL7665S. Features. Applications. Pinout. CMOS Micropower Over/Under Voltage Detector. FN3182 Rev Page 1 of 15. FN3182 Rev 10.
DATASHEET ICL7665S CMOS Micropower Over/Under Voltage Detector The ICL7665S super CMOS micropower Over/Under voltage detector contains two low power, individually programmable voltage detectors on a single
More informationDATASHEET ISL28271, ISL Features. Ordering Information. Applications. Related Literature. Pinout
NOT RECOMMENDED FOR NEW DESIGNS NO RECOMMENDED REPLACEMENT contact our Technical Support Center at 1-888-INTERSIL or www.intersil.com/tsc Dual Micropower, Single Supply, Rail-to-Rail Input and Output (RRIO)
More informationDATASHEET. Features. Applications EL6204. Laser Driver Oscillator. FN7219 Rev 3.00 Page 1 of 12. October 28, FN7219 Rev 3.00.
DATASHEET EL624 Laser Driver Oscillator The EL624 is a push-pull oscillator used to reduce laser noise. It uses the standard interface to existing ROM controllers. The frequency and amplitude are each
More informationFeatures PKG. DWG. # M16.3 M16.3 M16.3 M16.15 M16.15 M16.15 E16.3. NUMBER OF RECEIVERS ACTIVE IN SHUTDOWN HIN232A +5V Capacitors No/No 0
DATASHEET HINA High Speed V Powered RS Transmitters/Receivers FN Rev.00 The HINA highspeed RS transmitter/receiver interface circuit meets all ElA highspeed RSE and V. specifications, and is particularly
More informationDATASHEET HA-5102, HA Pinouts. Ordering Information. Features. Applications. Dual and Quad, 8MHz, Low Noise Operational Amplifiers
DATASHEET HA-512, HA-514 Dual and Quad, 8Hz, Low Noise Operational Amplifiers FN2925 Rev 9. October 26, 24 Low noise and high performance are key words describing HA-512 and HA-514. These general purpose
More informationDATASHEET ISL83385E. Features. Ordering Information. Applications
NOT RECOMMENDED FOR NEW DESIGNS RECOMMENDED REPLACEMENT PART ICL3222EIVZ ±15kV ESD Protected, 3V to 5.5V, 1 Microamp, 250kbps, RS-232 Transmitters/Receivers DATASHEET FN6001 Rev 4.00 The Intersil ISL83385E
More informationISL Features. Related Literature. Applications*(see page 15) Application Block Diagram
USB 2.0 High-Speed/UART Dual SP3T (Dual 3 to 1 Multiplexer) FN7701 Rev 0.00 The Intersil ISL54216 is a single supply dual SP3T analog switch that operates from a single supply in the range of 2.7V to 4.6V.
More informationDATASHEET EL5462. Features. Pinout. Applications. Ordering Information. 500MHz Low Power Current Feedback Amplifier. FN7492 Rev 0.
DATASHEET EL5462 5MHz Low Power Current Feedback Amplifier The EL5462 is a current feedback amplifier with a bandwidth of 5MHz which makes this amplifier ideal for today s high speed video and monitor
More informationDATASHEET HIP1020. Features. Applications. Ordering Information. Pinout. Single, Double or Triple-Output Hot Plug Controller
DATASHEET HIP12 Single, Double or Triple-Output Hot Plug Controller The HIP12 applies a linear voltage ramp to the gates of any combination of 3.3V, V, and 12V MOSFETs. The internal charge pump doubles
More informationDATASHEET EL2125. Features. Applications. Ordering Information. Pinouts. Ultra-Low Noise, Low Power, Wideband Amplifier. FN7045 Rev 3.
DATASHEET EL Ultra-Low Noise, Low Power, Wideband Amplifier The EL is an ultra-low noise, wideband amplifier that runs on half the supply current of competitive parts. It is intended for use in systems
More information