20MHz to 134MHz Spread-Spectrum Clock Modulator for LCD Panels DS1181L
|
|
- Brooke Ross
- 5 years ago
- Views:
Transcription
1 Rev 1; /0 0MHz to 13MHz Spread-Spectrum General Description The is a spread-spectrum clock modulator IC that reduces EMI in high clock-frequency-based, digital electronic equipment. Using an integrated phase-locked loop (PLL), the accepts an input clock signal in the range of 0MHz to 13MHz and delivers a spread-spectrum modulated output clock signal. The PLL modulates, or dithers, the output clock about the center input frequency at a pin-selectable magnitude, allowing direct EMI control and optimization. In addition, through an enable pin the dithering can be enabled or disabled for easy comparison of system performance during EMI testing. This same input pin also allows the output to be three-stated. By dithering the system clock, all the address, data, and timing signals generated from this signal are also dithered so that the measured EMI at the fundamental and harmonic frequencies is greatly reduced. This is accomplished without changing clock rise/fall times or adding the space, weight, design time, and cost associated with mechanical shielding. The is provided in an -pin TSSOP package and operates over a full automotive temperature range of -0 C to +15 C. Applications LCD Panels for TVs, Desktop Monitors, and Notebook and Tablet PCs Automotive Telematics and Infotainment Printers Typical Operating Circuit appears at end of data sheet. Block Diagram Features Modulates a 0MHz to 13MHz Clock with Center Spread-Spectrum Dithering Selectable Spread-Spectrum Modulation Magnitudes of: ±0.5% ±1.0% ±1.5% ±.0% Low 75ps Cycle-to-Cycle Jitter Spread-Spectrum Disable Mode Pin Compatible with Alliance/PulseCore Semiconductor P00 Series Devices Clock Output Disable Low Cost Low Power Consumption 3.3V Single Voltage Supply -0 C to +15 C Temperature Range Small -Pin TSSOP Package Ordering Information PART TEMP RANGE PIN-PACKAGE E+ -0 C to +15 C TSSOP E+T -0 C to +15 C TSSOP +Denotes a lead(pb)-free/rohs-compliant package. T = Tape and reel. Pin Configuration CLKIN f IN = 0MHz TO 13MHz PLL WITH CENTER- DITHERED SPREAD- SPECTRUM SSO f SSO = 0MHz to 13MHz (DITHERED) TOP VIEW CLKIN CRSEL ENABLE LOGIC SSEN 3 SSO CRSEL CONFIGURATION DECODE AND CONTROL GND GND TSSOP 5 SSEN Maxim Integrated Products 1 For information on other Maxim products, visit Maxim s website at
2 ABSOLUTE MAXIMUM RATINGS Voltage Range on Relative to GND V to +.3V Voltage Range on Any Lead Relative to GND V to ( + 0.5V), not to exceed +.3V Operating Temperature Range...-0 C to +15 C Storage Temperature Range C to +15 C Soldering Temperature...See J-STD-00 Specification Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. RECOMMENDED OPERATING CONDITIONS (TA = -0 C to +15 C, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS Supply Voltage (Note 1) V 0. x + Input Logic 1 V IH x Input Logic 0 V IL -0.3 V Input Logic Float (SSEN, CRSEL) I FLOAT 0V < V IN < ±1 μa SSO < 0MHz 15 SSO Load C L 0MHz SSO < 13MHz 7 CLKIN Frequency f IN 0 13 MHz CLKIN Duty Cycle f INDC 0 0 % V pf DC ELECTRICAL CHARACTERISTICS ( = +3.0V to +3.V, T A = -0 C to +15 C, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS Supply Current I CC C L = 7pF, f IN = 13MHz 1 ma //CLKIN Input Leakage I IL:1 0V < V IN < μa CRSEL/SSEN Input Leakage I IL: 0V < V IN < μa Output Leakage (SSO) I OZ SSEN = float μa Low-Level Output Voltage (SSO) V OL I OL = ma 0. V High-Level Output Voltage (SSO) V OH I OH = -ma. V AC ELECTRICAL CHARACTERISTICS ( = +3.0V to +3.V, T A = -0 C to +15 C, unless otherwise noted.) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS SSO Duty Cycle f SSODC Measured at / 0 0 % SSO Rise Time t R C L = 7pF 1 ns SSO Fall Time t F C L = 7pF 1 ns Peak Cycle-to-Cycle Jitter t J T A = -0 C to +5 C,,000 cycles 75 ps Power-Up Time t POR (Note ) 50 ms Note 1: All voltages referenced to ground. Currents into the IC are positive and out of the IC are negative. Note : Time between power applied to device and stable output.
3 (T A = +5 C, unless otherwise noted.) SUPPLY CURRENT vs. SUPPLY VOLTAGE 1 ICC (ma) CLKIN = 13MHz CLKIN = MHz CLKIN = 0MHz toc01 ICC (ma) 1 SUPPLY CURRENT vs. TEMPERATURE CLKIN = 13MHz CLKIN = MHz CLKIN = 0MHz Typical Operating Characteristics toc0 ICC (ma) SUPPLY CURRENT vs. FREQUENCY 1 = 3.V = 3.0V toc03 C L = 7pF (V) 0-0 C L = 7pF 0 1 TEMPERATURE ( C) C L = 7pF FREQUENCY (MHz) DUTY CYCLE (%) DUTY CYCLE vs. SUPPLY VOLTAGE CLKIN = 7MHz toc0 DUTY CYCLE (%) DUTY CYCLE vs. TEMPERATURE CLKIN = 7MHz toc05 ATTENUATION (db) SPECTRUM ATTENUATION vs. FREQUENCY AT DIFFERENT DITHER AMPLITUDES f OUT = 7MHz 0.5% ±1.5% ±1% db 13dB 15dB 17dB ±% toc (V) TEMPERATURE ( C) 1 RBW = 10KHz CENTER DITHER FREQUENCY (MHz) 3
4 PIN NAME FUNCTION 1 CLKIN Clock Input. 0MHz to 13MHz clock input (f IN ). 3 GND Ground Pin Description Spread-Spectrum Magnitude Select Inputs. These digital inputs select the desired spread-spectrum magnitude as shown in the table below. MAGNITUDE SELECTED (%) 0 0 ± ± ± ±0.5 5 SSEN SSO Spread-Spectrum Enable. Three-level input to enable/disable spread-spectrum and to three-state the output. 0 = Power-up/spread-spectrum enabled. Float = SSO three-stated. 1 = Power-up/spread-spectrum disabled (not a bypass mode). Spread-Spectrum Clock Output. Outputs a center-dithered spread-spectrum version of the clock input at CLKIN. 7 CRSEL Supply Voltage Clock Range and Dither Rate Select. Three-level input that determines the dither rate. See the Detailed Description section for details. CRSEL CLKIN RANGE (MHz) DITHER RATE 0 to 13 Float 33 to to 3 f IN /3 Detailed Description The modulates an input clock to generate a center-dithered spread-spectrum output. A 0MHz to 13MHz clock is applied to the CLKIN pin. An internal PLL dithers the output clock about its center frequency at a user-selectable magnitude. Spread-Spectrum Dither Magnitude The can generate dither magnitudes up to ±%. The desired magnitude is selected using input pins and as shown in Table 1. Table 1. Dither Magnitude Spread-Spectrum Dither Rate The output spread-spectrum dither rate is fixed at f IN /3. Table. Dither Rate CRSEL CLKIN RANGE (MHz) 0 to 13 Float 33 to to 3 DITHER RATE f IN /3 MAGNITUDE SELECTED (%) 0 0 ± ± ± ±0.5
5 Spread-Spectrum Enable On power-up, the output clock (SSO) remains three-stated until the internal PLL reaches a stable frequency. The SSEN input can be used to disable the spread-spectrum modulation and to three-state the SSO output. If the SSEN pin is pulled high, the spread-spectrum modulation is turned off, but the device still uses the internal PLL to generate the clock signal at SSO. If the SSEN pin is floated, the output is three-stated. Applications Information Power-Supply Decoupling To achieve best results, it is highly recommended that a decoupling capacitor is used on the IC power-supply pins. Typical values of decoupling capacitors are 0.01µF and 0.1µF. Use a high-quality, ceramic, surface-mount capacitor, and mount it as close as possible to the and GND pins of the IC to minimize lead inductance. IF SSEN = 1 f IN + (0.5%, 1.0%, 1.5%, OR.0% OF f IN ) f IN f IN - (0.5%, 1.0%, 1.5%, OR.0% OF f IN ) DITHER AMOUNT (±0.5%, ±1.0%, ±1.5%, OR ±.0%) f SSO 1 DITHER CYCLE RATE CLKIN RANGE (MHz) DITHER RATE 0 TO 13 f IN /3 TIME Figure 1. Spread-Spectrum Frequency Modulation Typical Operating Circuit f IN = 0MHz TO 13MHz CLKIN CRSEL DECOUPLING CAPACITOR GND SSO SSEN f SSO DITHERED NOTE: IN THE ABOVE CONFIGURATION WITH,, AND SSEN CONNECTED TO GND AS WELL AS CRSEL CONNECTED TO, THE DEVICE IS CONFIGURED WITH A SPREAD-SPECTRUM MAGNITUDE OF ±.0%, AND ALLOWS A CLKIN BETWEEN 0MHz and 3MHz. Package Information For the latest package outline information and land patterns, go to PACKAGE TYPE PACKAGE CODE DOCUMENT NO. TSSOP H
6 REVISION NUMBER REVISION DATE DESCRIPTION Revision History PAGES CHANGED 0 11/07 Initial release. 1 /0 Increased the absolute maximum ratings range from +3.3V to +.3V. Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 10 San Gabriel Drive, Sunnyvale, CA Maxim Integrated Products Maxim is a registered trademark of Maxim Integrated Products, Inc.
DS1083L PLL WITH CENTER- SPREAD DITHERING CLOCK RATE DETECT CONFIGURATION DECODE AND CONTROL
Rev ; 5/7 1MHz to 13MHz Spread-Spectrum General Description The is a spread-spectrum clock modulator IC that reduces EMI in high-clock, frequency-based, digital electronic equipment. Using an integrated
More informationDS1080L. Spread-Spectrum Crystal Multiplier. General Description. Features. Applications. Ordering Information. Pin Configuration
General Description The DS80L is a low-jitter, crystal-based clock generator with an integrated phase-locked loop (PLL) to generate spread-spectrum clock outputs from 16MHz to 134MHz. The device is pin-programmable
More informationSpread-Spectrum Crystal Multiplier
General Description The MAX31180 is a low-jitter, crystal-based clock generator with an integrated phase-locked loop (PLL) to generate spread-spectrum clock outputs from 16MHz to 134MHz. The device is
More informationSpread-Spectrum Clock Generators
19-5214; Rev 0; 4/10 Spread-Spectrum Clock Generators General Description The are spread-spectrum clock generators that contain a phase-locked loop (PLL) that generates a 2MHz to 134MHz clock from an input
More informationDS1091L Automotive Temperature Range Spread-Spectrum EconOscillator
General Description The is a low-cost clock generator that is factory trimmed to output frequencies from 130kHz to 66.6MHz with a nominal accuracy of ±0.25%. The device can also produce a center- or down-dithered
More informationAutomotive Temperature Range Spread-Spectrum EconOscillator
General Description The MAX31091 is a low-cost clock generator that is factory trimmed to output frequencies from 200kHz to 66.6MHz with a nominal accuracy of ±0.25%. The device can also produce a center-spread-spectrum
More informationOSC2 Selector Guide appears at end of data sheet. Maxim Integrated Products 1
9-3697; Rev 0; 4/05 3-Pin Silicon Oscillator General Description The is a silicon oscillator intended as a low-cost improvement to ceramic resonators, crystals, and crystal oscillator modules as the clock
More informationDS4-XO Series Crystal Oscillators DS4125 DS4776
Rev 2; 6/08 DS4-XO Series Crystal Oscillators General Description The DS4125, DS4150, DS4155, DS4156, DS4160, DS4250, DS4300, DS4311, DS4312, DS4622, and DS4776 ceramic surface-mount crystal oscillators
More informationDS1090 OUTPUT FREQUENCY RANGE PIN- PACKAGE PART PRESCALER
Rev ; / PART OUTPUT FREQUENCY RANGE PRESCALER * PIN- PACKAGE U-1 MHz to MHz 1 µsop U-2* 2MHz to MHz 2 µsop U-* 1MHz to 2MHz µsop U-* 5kHz to 1MHz µsop U-16 U-32* 25kHz to 5kHz 125kHz to 25kHz 16 µsop 32
More information3V 10-Tap Silicon Delay Line DS1110L
XX-XXXX; Rev 1; 11/3 3V 1-Tap Silicon Delay Line General Description The 1-tap delay line is a 3V version of the DS111. It has 1 equally spaced taps providing delays from 1ns to ns. The series delay lines
More informationLow-Jitter, 8kHz Reference Clock Synthesizer Outputs MHz
19-3530; Rev 0; 1/05 Low-Jitter, 8kHz Reference General Description The low-cost, high-performance clock synthesizer with an 8kHz input reference clock provides six buffered LVTTL clock outputs at 35.328MHz.
More informationCLK_EN CLK_SEL. Q3 THIN QFN-EP** (4mm x 4mm) Maxim Integrated Products 1
19-2575; Rev 0; 10/02 One-to-Four LVCMOS-to-LVPECL General Description The low-skew, low-jitter, clock and data driver distributes one of two single-ended LVCMOS inputs to four differential LVPECL outputs.
More informationDS1088L 1.0. PART FREQUENCY (MHz) TEMP RANGE PIN-PACKAGE DS1088LU C to +85 C 8 µsop. DS1088LU C to +85 C 8 µsop
Rev 0; /0 % PART FREQUENCY (MHz) TEMP RANGE PIN-PACKAGE U-02 2.0 C to + C µsop U-.0 C to + C µsop U-1 1. C to + C µsop U-. C to + C µsop U-0 0.0 C to + C µsop U-yyy * C to + C µsop * 12kHz TO PUT TOP VIEW
More informationDS21600/DS21602/DS V/5V Clock Rate Adapter
DS21600/DS21602/DS21604 3.3V/5V Clock Rate Adapter www.maxim-ic.com GENERAL DESCRIPTION The DS21600/DS21602/DS21604 are multiple-rate clock adapters that convert between E-carrier and T- carrier clocks
More information3.3V Dual-Output LVPECL Clock Oscillator
19-4558; Rev 1; 3/10 3.3V Dual-Output LVPECL Clock Oscillator General Description The is a dual-output, low-jitter clock oscillator capable of producing frequency output pair combinations ranging from
More informationTOP VIEW. Maxim Integrated Products 1
19-3474; Rev 2; 8/07 Silicon Oscillator with Low-Power General Description The dual-speed silicon oscillator with reset is a replacement for ceramic resonators, crystals, crystal oscillator modules, and
More informationV OUT0 OUT DC-DC CONVERTER FB
Rev 1; /08 Dual-Channel, I 2 C Adjustable General Description The contains two I 2 C adjustable-current DACs that are each capable of sinking or sourcing current. Each output has 15 sink and 15 source
More informationTOP VIEW MAX9111 MAX9111
19-1815; Rev 1; 3/09 EVALUATION KIT AVAILABLE Low-Jitter, 10-Port LVDS Repeater General Description The low-jitter, 10-port, low-voltage differential signaling (LVDS) repeater is designed for applications
More informationSingle/Dual LVDS Line Receivers with Ultra-Low Pulse Skew in SOT23
19-1803; Rev 3; 3/09 Single/Dual LVDS Line Receivers with General Description The single/dual low-voltage differential signaling (LVDS) receivers are designed for highspeed applications requiring minimum
More informationEVALUATION KIT AVAILABLE GPS/GNSS Low-Noise Amplifier. Pin Configuration/Functional Diagram/Typical Application Circuit MAX2659 BIAS
19-797; Rev 4; 8/11 EVALUATION KIT AVAILABLE GPS/GNSS Low-Noise Amplifier General Description The high-gain, low-noise amplifier (LNA) is designed for GPS, Galileo, and GLONASS applications. Designed in
More informationLVDS/Anything-to-LVPECL/LVDS Dual Translator
19-2809; Rev 1; 10/09 LVDS/Anything-to-LVPECL/LVDS Dual Translator General Description The is a fully differential, high-speed, LVDS/anything-to-LVPECL/LVDS dual translator designed for signal rates up
More informationV CC 2.7V TO 5.5V. Maxim Integrated Products 1
19-3491; Rev 1; 3/07 Silicon Oscillator with Reset Output General Description The silicon oscillator replaces ceramic resonators, crystals, and crystal-oscillator modules as the clock source for microcontrollers
More information±80V Fault-Protected, 2Mbps, Low Supply Current CAN Transceiver
19-2425; Rev 0; 4/02 General Description The interfaces between the control area network (CAN) protocol controller and the physical wires of the bus lines in a CAN. It is primarily intended for industrial
More informationICS LOW EMI CLOCK GENERATOR. Description. Features. Block Diagram DATASHEET
DATASHEET ICS180-51 Description The ICS180-51 generates a low EMI output clock from a clock or crystal input. The device uses IDT s proprietary mix of analog and digital Phase-Locked Loop (PLL) technology
More informationSpread Spectrum Frequency Timing Generator
Spread Spectrum Frequency Timing Generator Features Maximized EMI suppression using Cypress s Spread Spectrum technology Generates a spread spectrum copy of the provided input Selectable spreading characteristics
More informationHART Modem DS8500. Features
Rev 1; 2/09 EVALUATION KIT AVAILABLE General Description The is a single-chip modem with Highway Addressable Remote Transducer (HART) capabilities and satisfies the HART physical layer requirements. The
More information140ms (min) WDO Pulse Period PART. Maxim Integrated Products 1
19-2804; Rev 2; 12/05 5-Pin Watchdog Timer Circuit General Description The is a low-power watchdog circuit in a tiny 5- pin SC70 package. This device improves system reliability by monitoring the system
More informationIF Digitally Controlled Variable-Gain Amplifier
19-2601; Rev 1; 2/04 IF Digitally Controlled Variable-Gain Amplifier General Description The high-performance, digitally controlled variable-gain amplifier is designed for use from 0MHz to 400MHz. The
More informationICS LOW EMI CLOCK GENERATOR. Description. Features. Block Diagram DATASHEET
DATASHEET ICS180-01 Description The ICS180-01 generates a low EMI output clock from a clock or crystal input. The device uses IDT s proprietary mix of analog and digital Phase Locked Loop (PLL) technology
More informationTOP VIEW REFERENCE VOLTAGE ADJ V OUT
Rev 1; 8/6 EVALUATION KIT AVAILABLE Electronically Programmable General Description The is a nonvolatile (NV) electronically programmable voltage reference. The reference voltage is programmed in-circuit
More informationEVALUATION KIT AVAILABLE GPS/GNSS Low-Noise Amplifiers
19456; Rev ; 8/1 EVALUATION KIT AVAILABLE GPS/GNSS Low-Noise Amplifiers General Description The / low-noise amplifiers (LNAs) are designed for GPS L1, Galileo, and GLONASS applications. Designed in Maxim
More informationDS1135L 3V 3-in-1 High-Speed Silicon Delay Line
3V 3-in-1 High-Speed Silicon Delay Line FEATURES All-Silicon Timing Circuit Three Independent Buffered Delays Stable and Precise Over Temperature and Voltage Leading and Trailing Edge Precision Preserves
More informationTwo-/Four-Channel, I 2 C, 7-Bit Sink/Source Current DAC
19-4744; Rev 1; 7/9 Two-/Four-Channel, I 2 C, 7-Bit Sink/Source General Description The DS4422 and DS4424 contain two or four I 2 C programmable current DACs that are each capable of sinking and sourcing
More information±15kV ESD-Protected 52Mbps, 3V to 5.5V, SOT23 RS-485/RS-422 True Fail-Safe Receivers
19-3; Rev 1; 3/11 ±1kV ESD-Protected Mbps, 3V to.v, SOT3 General Description The MAX38E/MAX381E/MAX383E/MAX384E are single receivers designed for RS-48 and RS-4 communication. These devices guarantee data
More informationECL/PECL Dual Differential 2:1 Multiplexer
19-2484; Rev 0; 7/02 ECL/PECL Dual Differential 2:1 Multiplexer General Description The fully differential dual 2:1 multiplexer (mux) features extremely low propagation delay (560ps max) and output-to-output
More informationEVALUATION KIT AVAILABLE Precision, High-Bandwidth Op Amp
19-227; Rev ; 9/1 EVALUATION KIT AVAILABLE Precision, High-Bandwidth Op Amp General Description The op amp features rail-to-rail output and MHz GBW at just 1mA supply current. At power-up, this device
More informationLow-Voltage, 1.8kHz PWM Output Temperature Sensors
19-266; Rev 1; 1/3 Low-Voltage, 1.8kHz PWM Output Temperature General Description The are high-accuracy, low-power temperature sensors with a single-wire output. The convert the ambient temperature into
More informationDual 1:5 Differential LVPECL/LVECL/HSTL Clock and Data Drivers
19-2079; Rev 2; 4/09 Dual 1:5 Differential LPECL/LECL/HSTL General Description The are low skew, dual 1-to-5 differential drivers designed for clock and data distribution. These devices accept two inputs.
More information50Ω, Low-Voltage, Quad SPST/Dual SPDT Analog Switches in WLP
9-266; Rev 3; /2 5Ω, Low-Voltage, Quad SPST/Dual SPDT Analog General Description The low-voltage, quad single-pole single-throw (SPST)/dual single-pole/double-throw (SPDT) analog switches operate from
More informationPeak Reducing EMI Solution
Peak Reducing EMI Solution Features Cypress PREMIS family offering enerates an EMI optimized clocking signal at the output Selectable input to output frequency Single 1.% or.% down or center spread output
More informationLVDS or LVTTL/LVCMOS Input to 14 LVTTL/LVCMOS Output Clock Driver
19-2392; Rev ; 4/2 LVDS or LVTTL/LVCMOS Input to General Description The 125MHz, 14-port LVTTL/LVCMOS clock driver repeats the selected LVDS or LVTTL/LVCMOS input on two output banks. Each bank consists
More informationP2042A LCD Panel EMI Reduction IC
LCD Panel EMI Reduction IC Features FCC approved method of EMI attenuation Provides up to 15dB of EMI suppression Generates a low EMI spread spectrum clock of the input frequency Input frequency range:
More informationS 500µA (typ) Supply Current S TSSOP 16-Pin Package S -40 C to +85 C Ambient Temperature Range S Functionally Compatible to DG411, DG412, and DG413
19-572; Rev ; 12/1 Quad SPST +7V Analog Switches General Description The are analog switches with a low on-resistance of 1I (max) that conduct equally well in both directions. All devices have a rail-to-rail
More informationICS LOW EMI CLOCK GENERATOR. Features. Description. Block Diagram DATASHEET
DATASHEET ICS10-52 Description The ICS10-52 generates a low EMI output clock from a clock or crystal input. The device uses ICS proprietary mix of analog and digital Phase-Locked Loop (PLL) technology
More informationLVTTL/CMOS DATA INPUT 100Ω SHIELDED TWISTED CABLE OR MICROSTRIP PC BOARD TRACES. Maxim Integrated Products 1
19-1927; Rev ; 2/1 Quad LVDS Line Driver with General Description The quad low-voltage differential signaling (LVDS) differential line driver is ideal for applications requiring high data rates, low power,
More informationLVTTL/LVCMOS DATA INPUT 100Ω SHIELDED TWISTED CABLE OR MICROSTRIP PC BOARD TRACES. Maxim Integrated Products 1
19-1991; Rev ; 4/1 EVALUATION KIT AVAILABLE General Description The quad low-voltage differential signaling (LVDS) line driver is ideal for applications requiring high data rates, low power, and low noise.
More informationHigh-Voltage, 350mA, Adjustable Linear High-Brightness LED (HB LED) Driver
19-383; Rev 1; 4/9 High-Voltage, 35mA, Adjustable Linear General Description The current regulator operates from a 6.5V to 4V input voltage range and delivers up to a total of 35mA to one or more strings
More informationLow-Cost Notebook EMI Reduction IC. Applications. Modulation. Phase Detector
Low-Cost Notebook EMI Reduction IC Features Provides up to 15dB of EMI suppression FCC approved method of EMI attenuation Generates a 1X low EMI spread spectrum clock of the input frequency Operates between
More informationSingle LVDS/Anything-to-LVPECL Translator
9-2808; Rev 0; 4/03 Single LVDS/Anything-to-LVPECL Translator General Description The is a fully differential, high-speed, anything-to-lvpecl translator designed for signal rates up to 2GHz. The s extremely
More informationMultiphase Spread-Spectrum EconOscillator
Rev 1; 5/04 Multiphase Spread-Spectrum EconOscillator General Description The is a silicon oscillator that generates four multiphase, spread-spectrum, square-wave outputs. Frequencies between 2MHz and
More informationDual-Rate Fibre Channel Repeaters
9-292; Rev ; 7/04 Dual-Rate Fibre Channel Repeaters General Description The are dual-rate (.0625Gbps and 2.25Gbps) fibre channel repeaters. They are optimized for use in fibre channel arbitrated loop applications
More informationCold-Junction-Compensated K-Thermocoupleto-Digital Converter (0 C to +128 C)
19-2241; Rev 1; 8/02 Cold-Junction-Compensated K-Thermocoupleto-Digital General Description The cold-junction-compensation thermocouple-to-digital converter performs cold-junction compensation and digitizes
More informationTOP VIEW COM2. Maxim Integrated Products 1
19-3472; Rev ; 1/4 Quad SPST Switches General Description The quad single-pole/single-throw (SPST) switch operates from a single +2V to +5.5V supply and can handle signals greater than the supply rail.
More informationPT7C4511. PLL Clock Multiplier. Features. Description. Pin Configuration. Pin Description
Features Zero ppm multiplication error Input crystal frequency of 5-30 MHz Input clock frequency of - 50 MHz Output clock frequencies up to 200 MHz Peak to Peak Jitter less than 200ps over 200ns interval
More informationICS CLOCK SYNTHESIZER FOR PORTABLE SYSTEMS. Description. Features. Block Diagram PRELIMINARY DATASHEET
PRELIMINARY DATASHEET ICS1493-17 Description The ICS1493-17 is a low-power, low-jitter clock synthesizer designed to replace multiple crystals and oscillators in portable audio/video systems. The device
More informationPI6C557-03AQ. PCIe 2.0 Clock Generator with 2 HCSL Outputs for Automotive Applications. Description. Features. Pin Configuration (16-Pin TSSOP)
PCIe.0 Clock Generator with HCSL Outputs for Automotive Applications Features ÎÎPCIe.0 compliant à à Phase jitter -.1ps RMS (typ) ÎÎLVDS compatible outputs ÎÎSupply voltage of 3.3V ±10% ÎÎ5MHz crystal
More informationLow-Cost, Remote Temperature Switch
19-1819; Rev 3; 2/11 Low-Cost, Remote Temperature Switch General Description The is a fully integrated, remote temperature switch that uses an external P-N junction (typically a diode-connected transistor)
More information800Mbps LVDS/LVPECL-to-LVDS 2 x 2 Crosspoint Switch
19-2003; Rev 0; 4/01 General Description The 2 x 2 crosspoint switch is designed for applications requiring high speed, low power, and lownoise signal distribution. This device includes two LVDS/LVPECL
More informationPA RT MAX3408EUK 100Ω 120Ω. Maxim Integrated Products 1
19-2141; Rev ; 8/1 75Ω/Ω/Ω Switchable Termination General Description The MAX346/MAX347/MAX348 are general-purpose line-terminating networks designed to change the termination value of a line, depending
More informationRail-to-Rail, 200kHz Op Amp with Shutdown in a Tiny, 6-Bump WLP
19-579; Rev ; 12/1 EVALUATION KIT AVAILABLE Rail-to-Rail, 2kHz Op Amp General Description The op amp features a maximized ratio of gain bandwidth (GBW) to supply current and is ideal for battery-powered
More informationICS NETWORKING CLOCK SYNTHESIZER. Description. Features. Block Diagram DATASHEET
DATASHEET Description The generates four high-quality, high-frequency clock outputs. It is designed to replace multiple crystals and crystal oscillators in networking applications. Using ICS patented Phase-Locked
More informationEVALUATION KIT AVAILABLE 300MHz to 450MHz High-Efficiency, Crystal-Based +13dBm ASK Transmitter 3.0V. 100nF DATA INPUT
19-31; Rev 4; /11 EVALUATION KIT AVAILABLE 300MHz to 450MHz High-Efficiency, General Description The crystal-referenced phase-locked-loop (PLL) VHF/UHF transmitter is designed to transmit OOK/ASK data
More informationLow-Cost, SOT23, Voltage-Output, High-Side Current-Sense Amplifier MAX4173T/F/H
19-13; Rev 5; /11 Low-Cost, SOT23, Voltage-Output, General Description The MAX173 low-cost, precision, high-side currentsense amplifier is available in a tiny SOT23-6 package. It features a voltage output
More informationPT7C4502 PLL Clock Multiplier
Features Low cost frequency multiplier Zero ppm multiplication error Input crystal frequency of 5-30 MHz Input clock frequency of 4-50 MHz Output clock frequencies up to 180 MHz Period jitter 50ps (100~180MHz)
More informationDS32kHz kHz Temperature-Compensated Crystal Oscillator
32.768kHz Temperature-Compensated Crystal Oscillator www.maxim-ic.com GENERAL DESCRIPTION The DS32kHz is a temperature-compensated crystal oscillator (TCXO) with an output frequency of 32.768kHz. This
More informationMK5811C LOW EMI CLOCK GENERATOR. Description. Features. Block Diagram DATASHEET
DATASHEET MK5811C Description The MK5811C device generates a low EMI output clock from a clock or crystal input. The device is designed to dither a high emissions clock to lower EMI in consumer applications.
More informationDS600. ±0.5 Accurate Analog-Output Temperature Sensor
www.maxim-ic.com GENERAL DESCRIPTION The is a ±0.5 C accurate analog-output temperature sensor. This accuracy is valid over its entire operating voltage range of and the wide temperature range of -20 C
More informationNETWORKING CLOCK SYNTHESIZER. Features
DATASHEET ICS650-11 Description The ICS650-11 is a low cost, low jitter, high performance clock synthesizer customized for BroadCom. Using analog Phase-Locked Loop (PLL) techniques, the device accepts
More informationMK SPREAD SPECTRUM MULTIPLIER CLOCK. Description. Features. Block Diagram DATASHEET
DATASHEET MK1714-01 Description The MK1714-01 is a low cost, high performance clock synthesizer with selectable multipliers and percentages of spread spectrum designed to generate high frequency clocks
More informationMK SPREAD SPECTRUM MULTIPLIER CLOCK. Description. Features. Block Diagram DATASHEET
DATASHEET MK1714-02 Description The MK1714-02 is a low cost, high performance clock synthesizer with selectable multipliers and percentages of spread designed to generate high frequency clocks with low
More informationTRIPLE PLL FIELD PROG. SPREAD SPECTRUM CLOCK SYNTHESIZER. Features
DATASHEET ICS280 Description The ICS280 field programmable spread spectrum clock synthesizer generates up to four high-quality, high-frequency clock outputs including multiple reference clocks from a low-frequency
More informationHigh-Efficiency LCD Boost with True Shutdown MAX8570 MAX8575
19-3329; Rev 3; 3/1 EVALUATION KIT AVAILABLE High-Efficiency LCD Boost General Description The family of LCD step-up converters uses an internal n-channel switch and an internal p-channel output isolation
More informationICS502 LOCO PLL CLOCK MULTIPLIER. Description. Features. Block Diagram DATASHEET
DATASHEET ICS502 Description The ICS502 LOCO TM is the most cost effective way to generate a high-quality, high-frequency clock output and a reference from a lower frequency crystal or clock input. The
More informationMANUAL RESET (MR) (RESET)/ RESET RESET MAX16084 MAX16085 MAX16086 GND. Maxim Integrated Products 1
19-5903; Rev 0; 6/11 General Description The family of supervisory circuits monitors voltages from +1.1V to +5V using a factory-set reset threshold. The MAX16084/MAX16085/MAX16086 offer a manual reset
More informationTOP VIEW. Maxim Integrated Products 1
19-2213; Rev 0; 10/01 Low-Jitter, Low-Noise LVDS General Description The is a low-voltage differential signaling (LVDS) repeater, which accepts a single LVDS input and duplicates the signal at a single
More informationTOP VIEW. HD Recorders TSSOP
9-446; Rev ; /8 EVALUATION KIT AVAILABLE Low-Cost, -Channel, HD/PS/SD/BP General Description The / integrated -channel video filters for high-definition (HD), progressive-scan (PS), standard-definition
More information10Ω, Quad, SPST, +3V Logic-Compatible Analog Switches
19-218; Rev 1; 9/8 1Ω, Quad, SPST, +3V Logic-Compatible General Description Maxim s analog switches feature low on-resistance (1Ω max) and 1.5Ω onresistance matching between channels. These switches are
More informationLow-Charge Injection, 16-Channel, High-Voltage Analog Switches MAX14800 MAX14803
19-4484; Rev 1; 9/09 Low-Charge Injection, 16-Channel, General Description The provide high-voltage switching on 16 channels for ultrasonic imaging and printer applications. The devices utilize HVCMOS
More informationHigh-Voltage Switch for Wireless Power
General Description The MAX20304 is a DPST switch intended for wirelesspower-circuit applications. The new application for the portable device is the magnetic card reader. There has been a method to use
More informationMAX4751/MAX4752/MAX Ω, Low-Voltage, Single-Supply Quad SPST Analog Switches
// General Description The // are low on-resistance, low-voltage, quad, single-pole/single-throw (SPST) analog switches that operate from a single +1.V to +3.V supply. These devices have fast switching
More informationICS NETWORKING AND PCI CLOCK SOURCE. Description. Features. Block Diagram DATASHEET
DATASHEET Description The is a low cost frequency generator designed to support networking and PCI applications. Using analog/digital Phase Locked-Loop (PLL) techniques, the device uses a standard fundamental
More informationReceiver for Optical Distance Measurement
19-47; Rev ; 7/9 EVALUATION KIT AVAILABLE Receiver for Optical Distance Measurement General Description The is a high-gain linear preamplifier for distance measurement applications using a laser beam.
More informationLOCO PLL CLOCK MULTIPLIER. Features
DATASHEET ICS501A Description The ICS501A LOCO TM is the most cost effective way to generate a high quality, high frequency clock output from a lower frequency crystal or clock input. The name LOCO stands
More informationPI6C557-03B. PCIe 3.0 Clock Generator with 2 HCSL Outputs. Features. Description. Pin Configuration (16-Pin TSSOP) Block Diagram
Features ÎÎPCIe 3.0 compliant à à PCIe 3.0 Phase jitter - 0.45ps RMS (High Freq. Typ.) ÎÎLVDS compatible outputs ÎÎSupply voltage of 3.3V ±10% ÎÎ5MHz crystal or clock input frequency ÎÎHCSL outputs, 0.8V
More informationICS7151A-50 SPREAD SPECTRUM CLOCK GENERATOR. Description. Features. Block Diagram DATASHEET
DATASHEET ICS7151A-50 Description The ICS7151A-50 is a clock generator for EMI (Electromagnetic Interference) reduction. Spectral peaks are attenuated by modulating the system clock frequency. Down or
More informationIDT5V60014 LOW PHASE NOISE ZERO DELAY BUFFER. Description. Features. Block Diagram DATASHEET
DATASHEET IDT5V60014 Description The IDT5V60014 is a high speed, high output drive, low phase noise Zero Delay Buffer (ZDB) which integrates IDT s proprietary analog/digital Phase Locked Loop (PLL) techniques.
More informationMAX3280E/MAX3281E/ MAX3283E/MAX3284E ±15kV ESD-Protected 52Mbps, 3V to 5.5V, SOT23 RS-485/RS-422 True Fail-Safe Receivers
General Description The are single receivers designed for RS-48 and RS-4 communication. These devices guarantee data rates up to Mbps, even with a 3V power supply. Excellent propagation delay (1ns max)
More informationDescription. This Clock Multiplier is the most cost-effective way to Input crystal frequency of 5-40 MHz
PT7C4512 Features Description Zero ppm multiplication error This Clock Multiplier is the most cost-effective way to Input crystal frequency of 5-40 MHz generate a high quality, high frequency clock outputs
More informationTOP VIEW COUT1 COM2. Maxim Integrated Products 1
19-77; Rev ; 7/4.75Ω, Dual SPDT Audio Switch with General Description The dual, single-pole/double-throw (SPDT) switch operates from a single +2V to +5.5V supply and features rail-to-rail signal handling.
More informationMAX15070A/MAX15070B 7A Sink, 3A Source, 12ns, SOT23 MOSFET Drivers
General Description The /MAX15070B are high-speed MOSFET drivers capable of sinking 7A and sourcing 3A peak currents. The ICs, which are an enhancement over MAX5048 devices, have inverting and noninverting
More informationPin Configurations/Functional Diagrams/Truth Table COM COM GND MAX4644 OFF OFF. Maxim Integrated Products 1
9-7; Rev ; 3/ High-Speed, Low-Voltage, 4Ω, General Description The is a single-pole/double-throw (SPDT) switch that operates from a single supply ranging from +.8V to +.V. It provides low 4Ω on-resistance
More informationICS QUAD PLL CLOCK SYNTHESIZER. Description. Features. Block Diagram PRELIMINARY DATASHEET
PRELIMINARY DATASHEET ICS348-22 Description The ICS348-22 synthesizer generates up to 9 high-quality, high-frequency clock outputs including multiple reference clocks from a low frequency crystal or clock
More information5- to 10-Cell Li+ Protector with Cell Balancing
Rev 0; 4/08 5- to 10-Cell Li+ Protector with Cell Balancing General Description The provides full charge and discharge protection for 5- to 10-cell lithium-ion (Li+) battery packs. The protection circuit
More informationI O 7-BIT POT REGISTER ADDRESS COUNT 7-BIT POT. CODE 64 (40h) DS3503
Rev 1; 3/9 NV, I2C, Stepper Potentiometer General Description The features two synchronized stepping digital potentiometers: one 7-bit potentiometer with RW as its output, and another potentiometer with
More informationSingle/Dual LVDS Line Receivers with In-Path Fail-Safe
9-2578; Rev 2; 6/07 Single/Dual LVDS Line Receivers with General Description The single/dual low-voltage differential signaling (LVDS) receivers are designed for high-speed applications requiring minimum
More informationICS650-40A ETHERNET SWITCH CLOCK SOURCE. Description. Features. Block Diagram DATASHEET
DTSHEET ICS650-40 Description The ICS650-40 is a clock chip designed for use as a core clock in Ethernet Switch applications. Using IDT s patented Phase-Locked Loop (PLL) techniques, the device takes a
More informationPCI-EXPRESS CLOCK SOURCE. Features
DATASHEET ICS557-01 Description The ICS557-01 is a clock chip designed for use in PCI-Express Cards as a clock source. It provides a pair of differential outputs at 100 MHz in a small 8-pin SOIC package.
More informationEVALUATION KIT AVAILABLE 3.5GHz Downconverter Mixers with Selectable LO Doubler. PART MAX2683EUE MAX2684EUE *Exposed pad TOP VIEW IFOUT+ IFOUT-
-; Rev ; / EVALUATION KIT AVAILABLE.GHz Downconverter Mixers General Description The MAX/MAX are super-high-performance, low-cost downconverter mixers intended for wireless local loop (WLL) and digital
More information6500V/µs, Wideband, High-Output-Current, Single- Ended-to-Differential Line Drivers with Enable
99 Rev ; /99 EVALUATION KIT AVAILABLE 65V/µs, Wideband, High-Output-Current, Single- General Description The // single-ended-todifferential line drivers are designed for high-speed communications. Using
More information27pF TO ADC C FILTER (OPTIONAL) Maxim Integrated Products 1
19-215; Rev 6; 9/6 EVALUATION KIT AVAILABLE RF Power Detectors in UCSP General Description The wideband (8MHz to 2GHz) power detectors are ideal for GSM/EDGE (MAX226), TDMA (MAX227), and CDMA (MAX225/MAX228)
More information