BULLeTIN PeM CAPTIve PANeL SCReWS 617 Rev 1117

Transcription

1 BULLTIN PF PM PTIV PNL SRWS 617 R e v 1117

2 PM PTIV PNL SRWS PM brand captive panel screws are designed to help keep parts to a minimum and eliminate risks associated with loose hardware that could fall out and damage internal components. These panel fastener assemblies are ideal to attach metal panels or other thin material components in applications where subsequent access will be necessary. PF11 /PF12 /PF11M /PF12M large knob, spring-loaded self-clinching panel screws - PG 5 PF11MF large knob, spring-loaded flaremounted captive panel screws - PG 6 PF2 /PFS2 screw head, spring-loaded captive panel screws - PG 16 PTL2 /PSL2 locating pin, spring-loaded plunger assemblies - PG 17 PF11MW large knob, spring-loaded flaremounted, floating captive panel screws - PG 7 PF11PM large knob, spring-loaded plastic PM..P.S. captive panel screws - PG 8 PFHV screw head, no spring captive panel screws - PG 9 SBR tool only, spinning clinch bolt with spring - PG 18 SB /SBJ tool only, spinning clinch bolts, no spring - PG 19 HSB, HSR, and HSL heat sink mounting fastener system - PGS 2-21 PF7M screw head, spring-loaded selfclinching captive panel screws - PG 1 PF1 tool only, flush-mounted captive panel screws, no spring - PGS PF7MF flare-mounted captive panel screws for installing into stainless steel - PG 11 PF3 low-profile knob, spring-loaded captive panel screws - PG 12 PF5 and PF6 low-profile knob, springloaded captive panel screws - PG 13 RLFST SMTPFLSM surface mount spring-loaded captive panel screws - PG 24 RLFST SMTPF surface mount, panel screw components and assembly data - PG 25 PFK screw head, spring-loaded broaching captive panel screws - PG 26 PF4 recessed-head captive panel screws for installing into stainless steel - PG 14 PF2P tool only, non flush, spring-loaded captive panel screws - PG 15 Value-added capabilities - PG 27 aptive panel screw installation - PGS aptive panel screw performance data - PGS aptive panel screw capabilities - PG 42 HIGHT OMPRISON GUID ND STNDRD DRIVR RSS Installed and fastened height above sheet for M3 size. PF7M/PF7MF PF2P PF4 PF2/PFS2 PFK PF5/PF51/PF52 PF6/PF61/PF62 PF3/31/32 PF11/PF12 PF11M/PF12M PF-2 Pennngineering

3 PTIV PNL SRW SLTOR GUID PM Panel Fastener Page No. PF11 5 PF11M 5 PF12 5 PF12M 5 PF11MF 6 PF12MF 6 PF11MW 7 PF12MW 7 PM..P.S. 8 (1) PFHV 9 PF7M 1 PF7MF 11 PF3 PF31 12 PF32 PF5 PF51 13 PF52 PF6 PF61 13 PF62 PF4 14 PF2P 15 PF2 16 PFS2 16 SBR 18 SB/SBJ 19 HSB 2-21 PF SMTPFLSM 24 SMTPF 25 (1) PFK 26 (1) Standard color is black. pplication Requires: ctuation Installs into Includes Painted vailable anti Mating High Printed Stainless panels Multiple Flush vailable in cross- hole UL corrosion Spring Tool Hand Thinner circuit steel and/or any screw mounted in custom threading misa- pproved resistance loaded sheets boards sheet hardness lengths top side black colors feature lignment PF11MF PF11MW PM..P.S. HSB PFHV SBR SB/SBJ PF1 Pennngineering PF-3

4 PM PF11 /PF12 PTIV PNL SRWS PM PF11/PF12 panel fasteners provide design flexibility by offering three styles of installation types, each having the same profile or look above the sheet or panel into which it is installed. The various mounting types include self-clinching, flare-mounted, and floating styles. ach offers a distinct advantage depending on your application. The standard selection of knobs include knurled or smooth metal caps and plastic PM..P.S. (colored access panel screws). Self-clinching Flare-mounted Floating Key features include: 1) Universal Phillips/slot drive (except for plastic cap). 2) Shoulder on retainer to provide positive stop during installation. 3) nti cross-threading feature (designated with an M in the part number). ases assembly, aligns components, improves assembly line productivity, prevents jamming, and slides through clogged internal threads. 1 Universal Phillips/ slot drive* 3 NTI ROSS-THRD THNOLOGY - HOW IT WORKS Pennngineering is a licensee for M technology, a registered trademark of M Inc. 2 Shoulder on retainer -1- MISLIGND XIS -2- THRDS M -3- THRDS DRIV NORMLLY * Plastic cap version has Phillips drive only. Standard Mounting Styles: Self-clinching Installs flush on back side of panel. vailable in three screw lengths. Flare-mounted ppropriate for close centerline-to-edge applications. Doesn t require high installation force. Installs into any panel hardness. Installs flush on back side of panel. an be installed into most any thin material. ppropriate for painted panels. Flare-mounted, Floating ompensates for mating hole misalignment. Installs into any panel hardness. Standard ap Selection: Metal ap knurled ll metal cap available with knurls. Metal ap Un-knurled ll metal cap available without knurls. Black Metal ap DuraBlack finish is scratch resistant. Finish is on both metal cap and screw. (finish code BL ) Plastic ap vailable with custom color plastic cap. (See page 8 for colors) vailable Drive onfigurations: PF11 PF11P PF11LS PF11S PF11L Phillips/slot (Standard - except for plastic cap) Phillips (Optional) Torx /Slot ombination (Optional) Slotted (Optional) Torx (Optional) Pennngineering is a licensee for cument Global Technologies (Torx ). PF-4 Pennngineering

5 PM PF11 /PF12 /PF11M /PF12M PTIV PNL SRWS PF11 Knurled ap Shoulder provides positive stop during installation. PF12 Smooth ap Dimples on head designate metric thread. T 2 T 1 Phillips driver size. (See chart) s: xternal, SM B1.1, 2 / SM B1.13M, 6g Knob: luminum Retainer: Hardened arbon Steel Screw (PF11/PF12): 4 Series Stainless Steel Screw (PF11M/PF12M): Hardened arbon Steel (1) Spring: 3 Series Stainless Steel Optional Finish (BL): Knob: Natural Finish Knob: Black anodize (2) Retainer: Bright nickel over copper flash Screw: Black nitride, per STM B689 MS2753, Section 3 (2) Screw (PF11/PF12): Passivated and/or tested per STM 38 Screw: (PF11M/PF12M): Zinc plated, 5µm, colorless (3) Spring: Natural Finish For use in sheet hardness: HRB 8 or less (Hardness Rockwell B Scale) / HB 15 or less (Hardness Brinell) G P linching profile may vary. Float.25mm minimum, in all directions from center,.5mm total. Installation Data page 28. Performance Data page 36. PRT NUMBR DSIGNTION PF11 M M3 1 BL Optional nti-cross thread feature Screw Length Optional DuraBlack finish ll dimensions are in millimeters. Size x Knurled Smooth Pitch ap ap M3 x.5 M3.5 x.6 M4 x.7 M5 x.8 M6 x 1 PF11 PF11M PF11 PF11M PF11 PF11M PF11 PF11M PF11 PF11M PF12 PF12M PF12 PF12M PF12 PF12M PF12 PF12M PF12 PF12M Screw Length Max. Min. Sheet Thickness Hole Size In Sheet +.8 Min. Dist. G P T 1 T 2 Driver Hole Max. ±.25 ±.64 ±.64 Nom. Nom. Size /LTo dge 4.32 M # M # M # M # M # (1) s with all lass 2/6g external threads with an additive finish, the maximum major and pitch, after plating, may equal basic sizes and be gauged to lass 3/4h, per NSI B1.1, Section 8, Table 3 and NSI B1.13M, Section 8, Paragraph 8.2. (2) BL suffix will be added to part number to designate DuraBlack finish. (3) See PM Technical Support section of our website ( for related plating standards and specifications. Pennngineering PF-5

6 PM PF11MF FLR-MOUNTD PTIV PNL SRWS PF11MF Knurled ap PF12MF Smooth ap Dimples on head designate metric thread. Phillips driver size. (See chart) s: xternal, SM B1.1, 2 / SM B1.13M, 6g (1) Knob: luminum Retainer: luminum Screw: Hardened arbon Steel Spring: 3 Series Stainless Steel Optional Finish (BL): Knob: Natural Finish Knob: Black anodize (2) Retainer: Natural Finish Screw: Black nitride Screw: Zinc plated, 5µm, colorless (3) MS2753, Spring: Natural Finish Section 3 (2) Shoulder provides positive stop during installation. T 2 T 1 PRT NUMBR DSIGNTION PF11 M F M3 1 BL PF12 M F M3 1 G P Float.25mm minimum, in all directions from center,.5mm total. nti-cross Feature Flaremounted Style Screw Length Optional DuraBlack finish Installation Data page 28. Performance Data page 36. ll dimensions are in millimeters. Size x Knurled Smooth Pitch ap ap Screw Length Max. Min. Sheet Thickness Hole Size In Sheet +.1 G P T 1 T 2 Driver Max. ±.25 ±.64 ±.64 Nom. Nom. Size 4.32 M3 x.5 PF11MF PF12MF M # M4 x.7 PF11MF PF12MF M # M5 x.8 PF11MF PF12MF M # M6 x 1 PF11MF PF12MF M # (1) s with all lass 2/6g external threads with an additive finish, the maximum major and pitch, after plating, may equal basic sizes and be gauged to lass 3/4h, per NSI B1.1, Section 8, Table 3 and NSI B1.13M, Section 8, Paragraph 8.2. (2) BL suffix will be added to part number to designate DuraBlack finish. (3) See PM Technical Support section of our website ( for related plating standards and specifications. PF-6 Pennngineering

7 PM PF11MW FLR-MOUNTD, FLOTING PTIV PNL SRW s: xternal, SM B1.1, 2 / SM B1.13M, 6g (1) Dimples on head designate metric thread. Knob: luminum Retainer: luminum Screw: Hardened arbon Steel Spring: 3 Series Stainless Steel Washer: 3 Series Stainless Steel PF11MW Knurled ap PF12MW Smooth ap Phillips driver size. (See chart) Optional Finish (BL): Knob: Natural Finish Knob: Black anodize (2) Retainer: Natural Finish Screw: Black nitride, Screw: Zinc plated, 5µm, colorless (3) MS2753, Spring: Natural Finish Section 3 (2) Washer: Natural Finish Shoulder provides positive stop during installation. W T 2 L.64mm Nom. T 1 G PNL ONFIGURTION 1 For applications where a space between mating panels is acceptable. D PNL ONFIGURTION 2 For applications where a space between mating panels is not acceptable. D B H PRT NUMBR DSIGNTION PF11 M W M3 1 1 BL PF12 M W M3 1 1 Installation Data page 29. Performance Data page 36. nticross style Floating Feature Shank (4) Screw Length (4) PF11MW panel fasteners are shipped with mating washers. Optional DuraBlack finish ll dimensions are in millimeters. Screw D Hole Size Shank Length Max. B In Sheet G H L T 1 T 2 Driver Min. W Size x Knurled Smooth Sheet Min. +.8 ±.25 Nom. Min. Nom. Nom. Nom. Size Total Nom. Pitch ap ap (4) (4) Thickness.3 Float M3 x.5 PF11MW PF12MW M M3.5 x.6 PF11MW PF12MW M M4 x.7 PF11MW PF12MW M M5 x.8 PF11MW PF12MW M M6 x 1 PF11MW PF12MW M # # # # # (1) s with all lass 2/6g external threads with an additive finish, the maximum major and pitch, after plating, may equal basic sizes and be gauged to lass 3/4h, per NSI B1.1, Section 8, Table 3 and NSI B1.13M, Section 8, Paragraph 8.2. (2) BL suffix will be added to part number to designate DuraBlack finish. (3) See PM Technical Support section of our website ( for related plating standards and specifications. (4) Other shank and screw lengths available. Pennngineering PF-7

8 PM..P.S. PTIV PNL SRWS olor apabilities (1) hoose a knob color code and add it to the end of the base part number. Dimples on head designate metric thread. Patented. Red = R Orange = N Yellow = Y Green = G Blue = U Violet = V Metallic = M Phillips driver size. (See chart) PM..P.S. dot pattern (Registered trademark) Black = B (Standard) s: xternal, SM B1.1, 2 / SM B1.13M, 6g (2) Knob: P/BS (UL 94V-, halogen-free) (3) Retainer: Hardened arbon Steel Screw: Hardened arbon Steel Spring: 3 Series Stainless Steel Shoulder provides positive stop during installation. T 2 T 1 Retainer: N - Bright nickel over copper flash per STM B689 Screw: Zinc plated, 5µm, colorless (4) Spring: Natural Finish For use in sheet hardness: HRB 8 or less (Hardness Rockwell B Scale) HB 15 or less (Hardness Brinell) ll dimensions are in millimeters. Installation Data page 28. Performance Data page 37. Size x Pitch P Knurled ap linching profile may vary. Float.25mm minimum, in all directions from center,.5mm total. Screw Min. Hole Size Length (Shank) Sheet In Sheet Max. Thickness +.8 G PRT NUMBR DSIGNTION PF11 P M M3 B lso available with flare-mounted retainer as PF11PMF or with floating style retainer as PF11PMW. Min. Dist. G P T 1 T 2 Driver Hole Max. ±.25 ±.64 ±.64 Nom. Nom. Size /LTo dge 4.32 M3 x.5 PF11PM M # M4 x.7 PF11PM M # M5 x.8 PF11PM M # Phillips Drive nticross Feature Screw Length olor (Standard Black) (1) The colors shown (except for black) are non-stocked standards and available on special order. Since actual color knob may vary slightly from those represented, we recommend that you request samples for color verification. If you require a custom color or you need a color matched knob, please contact us. (2) s with all lass 2/6g external threads with an additive finish, the maximum major and pitch, after plating, may equal basic sizes and be gauged to lass 3/4h, per NSI B1.1, Section 8, Table 3 and NSI B1.13M, Section 8, Paragraph 8.2. (3) Temperature limit is 21 F / 99. (4) See PM Technical Support section of our website ( for related plating standards and specifications. PF-8 Pennngineering

9 PM PFHV PTIV PNL SRWS Low cost captive screw design to replace loose hardware. Small, compact and low profile design for limited access areas. Two screw lengths. Universal slot/phillips recess standard. vailable with M anti cross-thread technology. (See page 4 for more information). vailable with Torx recess. T 2 P Phillips driver size. (See chart) Dimples on head designate metric thread. For available drive configurations, see page 4. Installation Data page 29. Performance Data page 37. H Shoulder provides positive stop during installation. linching profile may vary. T 1 G s: xternal, SM B1.1, 2 / SM B1.13M, 6g (1) Retainer: arbon Steel Screw: Hardened arbon Steel Retainer: N - Bright nickel over copper flash per STM B689 Screw: N - Bright nickel over copper flash per STM B689 (1) For use in sheet hardness: HRB 6 or less (Hardness Rockwell B Scale) HB 17 or less (Hardness Brinell) PRT NUMBR DSIGNTION PFHV M3 N Size Screw Length Finish ll dimensions are in millimeters. Screw Min. Hole Size Min. Dist. Size x Length (Shank) Sheet In Sheet G H P T 1 T 2 Driver Hole/L Pitch Max. Thickness +.8 Max. ±.25 ±.64 ±.13 ±.64 Nom. Nom. Size To dge M3 x.5 PFHV M3 M3.5 x.6 PFHV M3.5 M4 x.7 PFHV M # # #2 6.7 (1) s with all lass 2/6g external threads with an additive finish, the maximum major and pitch, after plating, may equal basic sizes and be gauged to lass 3/4h, per NSI B1.1, Section 8, Table 3 and NSI B1.13M, Section 8, Paragraph 8.2. Pennngineering PF-9

10 PM PF7M /PF7MF PTIV PNL SRWS Smallest footprint, spring-loaded panel fastener for limited access areas. M anti cross-thread technology. (See page 4 for more information). Installs flush on back side of panel. PF7M Self-clinching mounting design provides high pushout resistance. PF7M does not require special hole preparation. PF7MF is appropriate for close centerline-to-edge applications. PF7MF does not require high installation force. PF7MF installs into any panel hardness. vailable with Torx recess. PF7M PF7MF PF7M SLF-LINHING PTIV PNL SRWS Patented. Shoulder provides positive stop during installation. H P T2 Dimples on head designate metric thread. linching profile may vary. Installation Data page 3. Performance Data page 37. T1 G Phillips driver size. (See chart) s: xternal, SM B1.1, 2 / SM B1.13M, 6g (1) Retainer: arbon Steel Screw: Hardened arbon Steel Spring: 3 Series Stainless Steel Retainer: N - Bright nickel over copper flash per STM B689 Screw: N - Bright nickel over copper flash per STM B689 Spring: Natural Finish For use in sheet hardness: HRB 6 or less (Hardness Rockwell B Scale) HB 17 or less (Hardness Brinell) PRT NUMBR DSIGNTION PF7 M M3 N nti ross-thread Feature Size Length Finish ll dimensions are in millimeters. Min. Fastener Screw Min. Hole Size Dist. Size x Material Length (Shank) Sheet In Sheet H G P T1 T2 Driver Hole/L Pitch Steel Max. Thickness +.8 Max. ±.25 ±.25 ±.64 ±.64 Nom. Nom. Size To dge M3 x.5 PF7M M # M4 x.7 PF7M M # (1) s with all lass 2/6g external threads with an additive finish, the maximum major and pitch, after plating, may equal basic sizes and be gauged to lass 3/4h, per NSI B1.1, Section 8, Table 3 and NSI B1.13M, Section 8, Paragraph 8.2. PF-1 Pennngineering

11 PM PF7M /PF7MF PTIV PNL SRWS PF7MF FLR-MOUNTD PTIV PNL SRWS Dimples on head designate metric thread. s: xternal, SM B1.1, 2 / SM B1.13M, 6g (1) Patented. H Phillips driver size. (See chart) Retainer: luminum Screw: Hardened arbon Steel Spring: 3 Series Stainless Steel Spring: Natural Finish Retainer: Natural finish Screw: N - Bright nickel over copper flash per STM B689 Shoulder provides positive stop during installation. T2 T1 PRT NUMBR DSIGNTION PF7 M F M3 G1 G2 nti ross-thread Feature Flaring Size Length Installation Data page 3. Performance Data page 37. ll dimensions are in millimeters. Fastener Screw Min. Hole Size Size x Material Length (Shank) Sheet In Sheet H G1 G2 T1 T2 Driver Pitch Steel Max. Thickness +.13 Max. ±.25 ±.25 ±.64 ±.64 Nom. Nom. Size M3 x.5 PF7MF M #2 M4 x.7 PF7MF M #2 (1) s with all lass 2/6g external threads with an additive finish, the maximum major and pitch, after plating, may equal basic sizes and be gauged to lass 3/4h, per NSI B1.1, Section 8, Table 3 and NSI B1.13M, Section 8, Paragraph 8.2. Pennngineering PF-11

12 PM PF3 /PF5 /PF6 PTIV PNL SRWS Low-profile design satisfies many functional and cosmetic requirements. onvenient large head for tool or finger operation. PF5/PF6 are available with Torx recess. PF5/PF6 are available with M anti cross-thread technology. (See page 4 for more information). PF3 Knurled ap PF5 Knurled ap PF6 Smooth ap PF3 LOW-PROFIL PTIV PNL SRWS vailable with DuraBlack TM finish (Finish BN ) Shoulder provides positive stop during installation. Diagonal knurl and groove on retainer identifies metric thread sizes. T 2 H T 1 linching profile may vary. Installation Data page 31. Performance Data page 38. G s: xternal, SM B1.1, 2 / SM B1.13M, 6g (1) Retainer: arbon Steel Screw: Hardened arbon Steel (#4-4 and M3 sizes only) arbon Steel (all other sizes) Spring: 3 Series Stainless Steel Retainer: N - Bright nickel over copper flash per STM B689 Screw: N - Bright nickel over copper flash per STM B689 Spring: Natural Finish Optional Retainer: BN - Black nitride, MS2753, Section 3 Screw: BN - Black nitride, MS2753, Section 3 For use in sheet hardness: HRB 6 or less (Hardness Rockwell B Scale) HB 17 or less (Hardness Brinell) PRT NUMBR DSIGNTION PF3 M3 3 N and Shank Size Screw Length Finish ll dimensions are in millimeters. Screw Min. Hole Size Min. Dist. G H T1 T2 Size x Length (Shank) Sheet In Sheet Hole/L Max. ±.25 ±.4 ±.13 Max. Nom. Pitch Max. Thickness +.8 To dge M3 x.5 PF M3 3 PF M4 x.7 PF M4 3 PF M5 x.8 PF M5 3 PF M6 x 1 PF32 M (1) s with all lass 2/6g external threads with an additive finish, the maximum major and pitch, after plating, may equal basic sizes and be gauged to lass 3/4h, per NSI B1.1, Section 8, Table 3 and NSI B1.13M, Section 8, Paragraph 8.2. PF-12 Pennngineering

13 PM PF3 /PF5 /PF6 PTIV PNL SRWS PF5 ND PF6 LOW-PROFIL PTIV PNL SRWS vailable with DuraBlack TM finish (Finish BN ) Shoulder provides positive stop during installation. P linching profile may vary. Installation Data page 31. Performance Data page 39. T 2 Groove on retainer and dimples on head designate metric thread. H Phillips driver size. (See chart) T 1 G s: xternal, SM B1.1, 2 / SM B1.13M, 6g (1) Knob: arbon Steel Retainer: arbon Steel Screw: arbon Steel Spring: 3 Series Stainless Steel Knob: N - Bright nickel over copper flash per STM B689 Retainer: N - Bright nickel over copper flash per STM B689 Screw: N - Bright nickel over copper flash per STM B689 Spring: Natural Finish Optional Knob: BN - Black Nitride, MS2753, Section 3 Retainer: BN - Black Nitride, MS2753, Section 3 Screw: BN - Black Nitride, MS2753, Section 3 For use in sheet hardness: HRB 6 or less (Hardness Rockwell B Scale) HB 17 or less (Hardness Brinell) PRT NUMBR DSIGNTION PF5 M3 1 N PF6 M3 1 N and Shank Size Screw Length Finish ll dimensions are in millimeters. Screw Min. Hole Size Min. Dist Size x Knurled Smooth Length (Shank) Sheet In Sheet +.4 G H P T 1 T 2 Driver Hole/L Pitch ap ap Max. Thickness +.8 Max..13 ±.64 ±.2 ±.64 Max. Nom. Size To dge PF5 PF6 M #1 6.6 M3 x.5 PF51 PF61 M #1 6.6 PF52 PF62 M #1 6.6 PF5 PF6 M #2 7.1 M3.5 x.6 PF51 PF61 M #2 7.1 PF52 PF62 M #2 7.1 PF5 PF6 M #2 7.4 M4 x.7 PF51 PF61 M #2 7.4 PF52 PF62 M #2 7.4 PF5 PF6 M #2 8.4 M5 x.8 PF51 PF61 M #2 8.4 PF52 PF62 M #2 8.4 M6 x 1 PF52 PF62 M #2 9.7 (1) s with all lass 2/6g external threads with an additive finish, the maximum major and pitch, after plating, may equal basic sizes and be gauged to lass 3/4h, per NSI B1.1, Section 8, Table 3 and NSI B1.13M, Section 8, Paragraph 8.2. Pennngineering PF-13

14 PM PF4 /PF2P PTIV PNL SRWS PF4/PF2P have fully concealed-head for tool only access. PF4/PF2P comply with UL 695 standards. PF4 installs into stainless steel sheets HRB 88 or less. PF4/PF2P are available with M anti cross-thread technology. (See page 4 for more information). PF4/PF2P available with Torx recess. PF4 PF2P PF4 RSSD-HD PTIV PNL SRWS INSTLLS INTO STINLSS STL Shoulder provides positive stop during installation. P T 2 linching profile may vary. Installation Data page 32. Performance Data page 39. Phillips driver size. (See chart) Dimples on head designates metric thread. T1 G PM Trademark Blue plastic retaining ring. s: xternal, SM B1.1, 2 / SM B1.13M, 6g Retainer: 4 Series Stainless Steel Screw: 4 Series Stainless Steel Spring: 3 Series Stainless Steel Retaining Ring: Nylon, temperature limit 93 Retainer: Passivated and/or tested per STM 38 Screw: Passivated and/or tested per STM 38 Spring: Natural Finish For use in sheet hardness: HRB 88 or less (Hardness Rockwell B Scale) HB 183 or less (Hardness Brinell) PRT NUMBR DSIGNTION PF4 M4 5 and Material Size Screw Length ll dimensions are in millimeters. Size x Pitch Screw Min. Hole Size Min. Dist G P T Length (Shank) Sheet In Sheet 1 T 2 Driver Hole/L Max. ±.25 ±.4 ±.64 Max. Nom. Size Max. Thickness +.8 To dge M3 x.5 PF4 M # M4 x.7 PF4 M # M5 x.8 PF4 M # NOT BOUT FSTNRS FOR STINLSS STL PNLS In order for self-clinching fasteners to work properly, the fastener must be harder than the sheet into which it is being installed. In the case of stainless steel panels, fasteners made from 3 Series Stainless Steel do not meet this hardness criteria. It is for this reason that 4 series fasteners are offered (PF4). However, while these 4 Series fasteners install and perform well in 3 Series stainless sheets they should not be used if the end product: Will be exposed to any appreciable corrosive presence. Requires non-magnetic fasteners. Will be exposed to any temperatures above 149 If any of the these are issues, please contact techsupport@pemnet.com for other options. PF-14 Pennngineering

15 PM PF4 /PF2P PTIV PNL SRWS PF2P RSSD-HD PTIV PNL SRWS Shoulder provides positive stop during installation. vailable with DuraBlack TM finish (Finish BN ) P T 2 linching profile may vary. Phillips driver size. (See chart) T1 G Dimples on head designates metric thread. PM Trademark Blue plastic retaining ring. s: xternal, SM B1.1, 2 / SM B1.13M, 6g Retainer: 3 Series Stainless Steel Screw: 4 Series Stainless Steel Spring: 3 Series Stainless Steel Retaining Ring: Nylon, temperature limit 93 Retainer: Passivated and/or tested per STM 38 Screw: Passivated and/or tested per STM 38 Spring: Natural Finish Optional Retainer: BN - Black nitride, MS2753, Section 3 Screw: BN - Black nitride, MS2753, Section 3 For use in sheet hardness: HRB 7 or less (Hardness Rockwell B Scale) HB 125 or less (Hardness Brinell) PRT NUMBR DSIGNTION PF2P M4 5 ll dimensions are in millimeters. Installation Data page 32. Performance Data page 39. and Material Size Screw Length Size x Pitch Screw Min. Hole Size Min. Dist G P T Length (Shank) Sheet In Sheet 1 T 2 Driver Hole/L Max. ±.25 ±.4 ±.64 Max. Nom. Size Max. Thickness +.8 To dge M3 x.5 PF2P M # M4 x.7 PF2P M # M5 x.8 PF2P M # M6 x 1 PF2P M # Pennngineering PF-15

16 PM PF2 /PFS2 PTIV PNL SRWS PF2/PFS2 PFS2 is available with DuraBlack TM finish (Finish BN ) PF2 s: xternal, SM B1.1, 2 / SM B1.13M, 6g Retainer: 3 Series Stainless Steel (2) Screw: 3 Series Stainless Steel Spring: 3 Series Stainless Steel Retaining Ring: Nylon, temperature limit 93 Retainer: Passivated and/or tested per STM 38 Screw: Passivated and/or tested per STM 38 Spring: Natural Finish Optional Retainer: BN - Black nitride, MS2753, Section 3 Screw: BN - Black nitride, MS2753, Section 3 For use in sheet hardness: HRB 7 or less (Hardness Rockwell B Scale) HB 125 or less (Hardness Brinell) PFS2 s: xternal, SM B1.1, 2 / SM B1.13M, 6g (1) Retainer: Hardened arbon Steel (2) Screw: arbon Steel Spring: 3 Series Stainless Steel Retaining Ring: Nylon, temperature limit 93 Retainer: N - Bright nickel over copper flash per STM B689 Screw: N - Bright nickel over copper flash per STM B689 Spring: Natural Finish Optional Retainer: BN - Black nitride, MS2753, Section 3 Screw: BN - Black nitride, MS2753, Section 3 For use in sheet hardness: HRB 8 or less (Hardness Rockwell B Scale) HB 15 or less (Hardness Brinell) Shoulder provides positive stop during installation. H T 2 T 1 Diagonal knurl identifies metric thread sizes. PRT NUMBR DSIGNTION PF2 M4 5 PFS2 M4 5 N P linching profile may vary. G PM Trademark Blue plastic retaining ring and Material Size Screw Length Finish Installation Data page 33. Performance Data page 39. ll dimensions are in millimeters. Screw Min. Hole Size Min. Dist. G H P T Length (Shank) Sheet In Sheet 1 T Size x 2 Hole/L Stainless Max. ±.25 ±.4 ±.13 ±.64 Max. Nom. Pitch Steel Max. Thickness +.8 To dge Steel M3 x.5 PF2 PFS2 M M4 x.7 PF2 PFS2 M M5 x.8 PF2 PFS2 M M6 x 1 PF2 PFS2 M (1) s with all lass 2/6g external threads with an additive finish, the maximum major and pitch, after plating, may equal basic sizes and be gauged to lass 3/4h, per NSI B1.1, Section 8, Table 3 and NSI B1.13M, Section 8, Paragraph 8.2. (2) The blue plastic retaining rings are a PM trademark. The temperature limit is 93. PF-16 Pennngineering

17 PM PTL2 /PSL2 SPRING-LODD PLUNGR SSMBLIS Used as positioning pins for sliding components such as drawer slides and equipment consoles. Fast installation and removal of components. Reverse side of sheet is flush when plunger is retracted. PTL2 has quick lockout feature to hold plunger in fully retracted position. For use in sheets of HRB 8 or less. vailable as PSL2 without lockout feature on special order. PTL2/PSL2 installed and with mating panel. Minimum mating hole diameter 6.38 mm. Plunger: Hardened arbon Steel Retainer: Hardened arbon Steel Spring: 3 Series Stainless Steel Plunger: N - Bright nickel over copper flash per STM B689 Retainer: N - Bright nickel over copper flash per STM B689 Spring: Natural Finish Lockout feature holds plunger in retracted position. Simply retract and twist to engage lockout feature. T 2 H 1 2 T 1 For use in sheet hardness: HRB 8 or less (Hardness Rockwell B Scale) HB 15 or less (Hardness Brinell) PRT NUMBR DSIGNTION PTL2 4 4 N Shoulder provides positive stop during installation. linching profile may vary. D G Plunger Diameter Plunger Length Finish Installation Data page 33. Performance Data page 39. ll dimensions are in millimeters. Plunger Plunger Min. Hole Size Min. Dist. D Diameter Length (Shank) Sheet In Sheet 1 2 G H T 1 T 2 Hole/L Max ±.25 ±.25 ±.25 ±.25 ±.25 Nom. Max. Thickness +.8 To dge PTL PSL2 (1) (1) Without lockout feature. vailable on special order. Pennngineering PF-17

18 PM SBR /SB /SBJ PTIV PNL SRWS Permanently captivates into sheets as thin as 1.2 mm and greater. Lowest cost captive screw design to replace loose hardware. vailable with self-retracting (SBR), axial float (SB), or jacking feature (SBJ). ppropriate for close centerline-to-edge applications. SBR SB SBJ SBR SPINNING LINH BOLT WITH SLF-RTRTING FTUR SBR retracted SBR engaged Phillips driver size. (See chart) H2 L H1 s: xternal, SM B1.1, 2 / SM B1.13M, 6g (1) Screw - Hardened arbon Steel Spring - 3 series stainless steel Screw - ZI - Zinc plated, 5µm, colorless (standard) (2) Spring: Natural Finish For use in sheet hardness: HRB 8 or less (Hardness Rockwell B Scale) HB 15 or less (Hardness Brinell) T PRT NUMBR DSIGNTION SBR M3 12 ZI ll dimensions are in millimeters. Min. Hole Size Min. Dist Size x Length L ±.4 Sheet in Sheet +.13 H 1 H 2 T Driver Hole /L Pitch (Length in millimeters) Thickness ±.13 Ref. Nom. Size To dge Installation Data page 34. Performance Data page 4. M3 x.5 SBR M #1 4.5 M4 x.7 SBR M #2 5.4 (1) s with all lass 2/6g external threads with an additive finish, the maximum major and pitch, after plating, may equal basic sizes and be gauged to lass 3/4h, per NSI B1.1, Section 8, Table 3 and NSI B1.13M, Section 8, Paragraph 8.2. (2) See PM Technical Support section of our website ( for related plating standards and specifications. Size Length Finish NOT: SBR screws are shipped with mating springs. For designs requiring a specific spring rate, contact our PM Technical Support group at techsupport@pemnet.com. PF-18 Pennngineering

19 PM SBR /SB /SBJ PTIV PNL SRWS SB /SBJ SPINNING LINH BOLTS SB with axial float. SBJ with jacking feature. SBJ T Phillips driver size. (See chart) s: xternal, SM B1.1, 2 / SM B1.13M, 6g (1) Hardened arbon Steel L H ZI - Zinc plated, 5µm, colorless (standard) (2) T SB Phillips driver size. (See chart) For use in sheet hardness: HRB 8 or less (Hardness Rockwell B Scale) HB 15 or less (Hardness Brinell) PRT NUMBR DSIGNTION SB J M3 6 ZI L H Installation Data page 34. Performance Data page 4. Jacking (If applicable) Size Length Finish ll dimensions are in millimeters. Min. Hole Size T Nom. Min. Dist. Size x Length L ±.4 Sheet in Sheet H Nom. xial Driver Hole/L Pitch Jacking Non-jacking (Length in millimeters) Thickness +.8 ±.25 Nom. Float Size To dge M3 x.5 SBJ M SB #1 3.3 M4 x.7 SBJ M #2 5 SB (1) s with all lass 2/6g external threads with an additive finish, the maximum major and pitch, after plating, may equal basic sizes and be gauged to lass 3/4h, per NSI B1.1, Section 8, Table 3 and NSI B1.13M, Section 8, Paragraph 8.2. (2) See PM Technical Support section of our website ( for related plating standards and specifications. Pennngineering PF-19

20 PM HSB HT SINK MOUNTING SYSTM The new HSB engineered mounting system provides secure attachment of a heat sink to the circuit board while providing firm contact to the chip component allowing optimum heat dissipation. The three-piece fastening system, sold individually, includes the screw, spring and receptacle nut. The clamp load created is determined by the spring rate and the amount of deflection that is designed into the joint of the hardware. The system also allows for slight expansion and contraction of the joint components without stress to the delicate circuitry. The unique click feature lets the user know when the fastener is completely installed. G NW! HSR HSL HSB Patented Screw can not be overtightened. udible click when fully engaged. Screw and spring mount together permanently into the heat sink. Spring determines clamp force. Receptacle nut mounts permanently to the P board. Provides even, constant contact of heat sink to chip component. llows removal of heat sink if desired. To select proper length code of nut/standoff: 1) Determine G, the distance from the top surface of the heat sink to the top of the P.. Board. 2) Find the combination of Screw (HSB) and Nut (HSR) whose sum of Screw Factor (SF) plus Nut Factor (NF) are closest to G. 3) Find D = G SF NF. The D value must be a negative number between zero and 1mm or 1/32 (1 dash length of HSR nut). 4) The actual working load is equal to the Spring (HSL) Working Load + (D x spring rate k). Lower D value results in lower force. If this or any standard product does not meet your application needs, contact our PM Technical Support group at techsupport@pemnet.com to develop a special product that matches your specific application. HSB SLF-PTIVTING SRW Phillips driver size. (See chart) S s: xternal, SM B1.1, 2 / SM B1.13M, 6g (1) Hardened carbon steel Screw - ZI - Zinc plated, 5µm, colorless (2) For use in sheet hardness: HRB 8 / HB15 or less (3) L H2 H1 PRT NUMBR DSIGNTION HSB M3 3 ZI ll dimensions are in millimeters. Length L ±.4 Min. Hole Size Screw Min. Dist Size x Sheet in Sheet S H1 H2 TS Factor Driver Hole/L Pitch 8.13 Thickness +.8 ±.25 Ref. Ref. Min. (SF) Size To dge M3 x.5 HSB M # NOT: HSB screws, HSR nuts and HSL springs are sold separately. TS Installation Data page 35. Performance Data page 4. (1) s with all lass 2/6g external threads with an additive finish, the maximum major and pitch, after plating, may equal basic sizes and be gauged to lass 3/4h, per NSI B1.1, Section 8, Table 3 and NSI B1.13M, Section 8, Paragraph 8.2. (2) See PM Technical Support section of our website ( for related plating standards and specifications. (3) HRB - Hardness Rockwell B Scale. HB - Hardness Brinell. Size Length Finish PF-2 Pennngineering

21 PM HSB HT SINK MOUNTING SYSTM HSR BROHING NUT/STNDOFF F TN N HSR nuts are available for surface mounting. ontact our PM technical support group at techsupport@pemnet.com. s: Internal, SM B1.1, 2B / SM B1.13M, 6H arbon steel T - lectro-plated tin STM B 545, class B with clear preservative coating, annealed (1) For use in sheet hardness: HRB 6 / HB 17 or less (2) PRT NUMBR DSIGNTION HSR M3 2 T Installation Data page 35. Performance Data page 4. Size Length Finish ll dimensions are in millimeters. Min. Hole Size Nut Min. Dist. Size x Length (Shank) Sheet In Sheet N F TN Factor Hole/L Pitch Max. Thickness +.8 ±.8 ±.13 ±.25 ±.13 (NF) To dge M3 x.5 HSR M NOT: HSB screws, HSR nuts and HSL springs are sold separately. (1) See PM Technical Support section of our website ( for related plating standards and specifications. (2) HRB - Hardness Rockwell B Scale. HB - Hardness Brinell. TYP HSL SPRINGS HSL springs are engineered to provide a reliable and repeatable spring rate when assembled with mating PM hardware. The spring rate is critical to the successful assembly of your heat sink. lamp load will be determined by the spring rate and deflection that is designed into the joint. Minimum Load at Working Spring Rate Part Inside Dia. Working Height ±1% Height Ref. k Spring Number (mm) (N) (mm) (N/mm) Material Spring I.D. Min. Working Height HSL Stainless Steel, Natural Finish NOT: HSB screws, HSR nuts and HSL springs are sold separately. HSL spring fits screw thread size M3. The HSL Inside Diameter is expressed in hundredths of millimeters. xample 574 indicates a minimum inside diameter of 5.74mm. PRT NUMBR DSIGNTION HSL The HSL Load is expressed in Newtons developed at the working height of the spring once the joint is assembled. xample 35 indicates working load of 35 Newtons. For designs requiring a specific spring rate, contact our PM Technical Support group at techsupport@pemnet.com Inside Diameter Load Pennngineering PF-21

22 PM PF1 FLUSH-MOUNTD PTIV PNL SRWS PF1 assembly sits flush in sheets as thin as 1.27 mm or flush on both sides in 3.2 mm sheets. PS1 screw remains captive in retainer when disengaged. PR1 retainer and F1 receptacle nut is for use in sheets of HRB 7 or less. N1 nut is for use in sheets of HRB 8 or less. omplies with UL 695 standards. M PS1 Screw B N1 Receptacle Nut PR1 Retainer PS1 Screw Manually Retracted Position T G P Installation Data page 36. Performance Data page 41. PR1 Retainer N1 Receptacle Nut ll dimensions are in millimeters. B G T M P Min. Nom. ±.25 Nom PS1 FLUSH MOUNTD SRWS ll dimensions are in millimeters. PS1 Screw Diagonal knurl identifies metric thread sizes. Screw H Size x Length +.5 Nom. Pitch -.15 L T ±.25 Nom. M3 x.5 PS1 M M4 x.7 PS1 M Flush Fasteners as retainers For applications where the screw head may project above the sheet surface, PS1 screws may be used with PMSRT F fasteners as retainers. For dimensions and engineering data on F fasteners, see PM Bulletin F. T H L Floating Receptacle Nuts s: xternal, SM B1.1, 2 / SM B1.13M, 6g 3 Series Stainless Steel Passivated and/or tested per STM 38 PRT NUMBR DSIGNTION PS1 M4 4 and Material vailable on special order F1 self-clinching floating receptacle nuts permit a minimum of.38mm adjustment for mating hole misalignment. Size Screw Length M5 x.8 PS1 M PF-22 Pennngineering

23 PM PF1 FLUSH-MOUNTD PTIV PNL SRWS PR1 SLF-LINHING FLUSH-MOUNTD RTINRS PR1 Retainer H B PRT NUMBR DSIGNTION PR1 M4 linching profile may vary. Size s: Internal, SM B1.1, 2B / SM B1.13M, 6H (1) 3 Series Stainless Steel Passivated and/or tested per STM 38 For use in sheet hardness: HRB 7 or less (Hardness Rockwell B Scale) HB 125 or less (Hardness Brinell) ll dimensions are in millimeters. Min. Sheet Min. Sheet Hole Size Min. Dist. B H Size x (Shank) for Self- for Flush in Sheet Hole/L Nom. Max. Nom. Nom. Pitch Max. linching Installation +.8 to dge M3 x.5 PR1 M M4 x.7 PR1 M M5 x.8 PR1 M N1 SLF-LINHING RPTL NUTS (4) N1 PRT NUMBR DSIGNTION s: H Internal, SM B1.1, 2B / SM B1.13M, 6H Receptacle Nut N1 M4 1 ZI F Hardened arbon Steel T ZI - Zinc plated, 5µm, colorless (standard) (3) Size Shank Finish For use in sheet hardness: HRB 8 or less (Hardness Rockwell B Scale) linching profile may vary. HB 15 or less (Hardness Brinell) ll dimensions are in millimeters. Min. Hole Size Min. Dist. Shank F H T Size x (Shank) Sheet In Sheet Hole/L Max. Nom. ±.25 Nom. ±.13 Pitch Max. Thickness +.8 To dge M3 x.5 N1 M M4 x.7 N1 M M5 x.8 N1 M (1) The purpose of the thread is for component screw retention only, thread may not accept 2B/6H Go threaded plug gage, but class 3/4h screw must pass with finger torque, may not reject NoGo threaded plug gage and minor diameter may exceed 2B/6H maximum. (2) 2B (unified) and 6H (metric) go gauge may stop at pilot end but class 3 (unified) and 4h (metric) screws will pass through with finger torque. (3) See PM Technical Support section of our website ( for related plating standards and specifications. (4) lso available on special order F1 self-clinching floating receptacle nuts. Pennngineering PF-23

24 RLFST SMTPFLSM SURF MOUNT PTIV PNL SRWS ll metal captive screw assembly installs in one piece utilizing pick and place method. ombination drive, Torx /slot. Solderable finish. s: xternal, SM B1.1, 2 / SM B1.13M, 6g (1) Retainer: arbon Steel Screw: Hardened arbon Steel Spring: 3 Series Stainless Steel Retainer: T - lectro-plated tin STM B545, lass B with preservative coating, annealed (2) Screw: ZI - Zinc plated, 5µm, colorless (3) Spring: Natural Finish Dimples on head designate metric thread. Torx /slot driver size. (See chart) 1 H PRT NUMBR DSIGNTION SMTPF LS M M3 T ll dimensions are in millimeters. Driver nti-cross Feature Length Finish Two Groove (Registered Trademark) G 1 G 2 2 T 2 T 1 Screw Min. ØK Hole Size ØD Min. Length (Shank) Sheet 1 2 G 1 G 2 H T 1 T 2 in Sheet Solder Driver Size Max. Thickness Max. ±.25 Nom ±.64 ±.64 ±.25 Nom. Nom. +.8 Pad Size M3 x.5 SMTPFLSM M T15 M3.5 x.6 SMTPFLSM M T15 ØD ØH Solder Pad Installation Data page 36. Performance Data page 41. Plated through hole not required. NUMBR OF PRTS PR RL Size Parts Per Reel M3 2 M Packaged on 33 mm recyclable reels. Tape width is 24 mm. Supplied with polyimide patch for vacuum pick up. Reels conform to I-481. (1) s with all lass 2/6g external threads with an additive finish, the maximum major and pitch, after plating, may equal basic sizes and be gauged to lass 3/4h, per NSI B1.1, Section 8, Table 3 and NSI B1.13M, Section 8, Paragraph 8.2 (2) Optimal solderability life noted on packaging. (3) See PM Technical Support section of our website ( for related plating standards and specifications. PF-24 Pennngineering

25 RLFST SMTPF SURF MOUNT PTIV PNL SRWS Retainer installed using conventional surface mount techniques. Simply snap screw into retainer to complete assembly. Black BS knob standard. Optional molded-through colors available. vailable with Torx recess. When ssembled s: xternal, SM B1.1, 2 / SM B1.13M, 6g (1) Knob: BS (2) Retainer: arbon Steel Screw: arbon Steel Retainer: T - lectro-plated tin STM B545, lass B with preservative coating, annealed Screw: N - Bright nickel over copper flash per STM B689 Spring action of plastic fingers holds screw in retracted position. P Board PSHP SMTPR P T 2 T 1 Patented. Installation Data page 36. Performance Data page 41. G B 1 1 R T L ll dimensions are in millimeters. Screw Part Number ssembly Dimensions Screw Dimensions Retainer Dimensions Screw Retainer Total Min. Size x Length Part G P T 1 T 2 Radial 1 1 L T (Shank) Sheet B R Pitch Number ±.64 ±.64 Nom. Nom. Float ±.25 ±.25 ±.38 Nom. Max. Thick. ±.8 Max. Nom. ±.13 M3 x.5 PSHP M SMTPR M3.5 x.6 PSHP M3.5 SMTPR RTINR - Packaged on 33 mm recyclable reels of 465 pieces. Tape width is 24 mm. Supplied with Kapton patch for vacuum pick up. Reels conform to I-481. SRW - Packaged in bags. Retainers and screws are sold separately. OLOR PBILITIS FOR PSHP SRW PRT NUMBR DSIGNTION FOR SRW PSHP M3 L 1 The colors shown here (codes #2 thru #7) are non-stocked standards and available on special order. Since actual cap colors may vary slightly from those shown here, we recommend that you request samples for color verification. If you require a custom color or you need a color matched cap, please contact us. Std. Black #1 Red #2 Orange #3 Yellow #4 Length ap Style (Lobed) olor (Standard Black) vailable with Torx recess on special order. Four dimples on head designate metric thread. PRT NUMBR DSIGNTION FOR RTINR SMTPR 6 1 T 1.6 mm Min. Retainer Size Shank Finish Solder Pad Plated through hole not required mm +.8 Green #5 Blue #6 Violet #7 Non-flammable UL 94-V plastic caps are available on special order. (1) s with all lass 2/6g external threads with an additive finish, the maximum major and pitch, after plating, may equal basic sizes and be gauged to lass 3/4h, per NSI B1.1, Section 8, Table 3 and NSI B1.13M, Section 8, Paragraph 8.2. (2) See PM Technical Support section of our website ( for related plating standards and specifications. Metal Phillips Recess M3 = #1 M3.5 = #2 Stencil Masking xamples Pennngineering PF-25

26 PFK BROHING PTIV PNL SRWS For permanent and reliable installation in P boards. Screw assemblies remain captive for easy mounting and removal. s: xternal, SM B1.1, 2 / SM B1.13M, 6g Diagonal knurl identifies metric thread sizes T 2 P Blue plastic retaining ring* (Trademark) T1 G H Shoulder provides positive stop during installation. Retainer: 3 Series Stainless Steel Screw: 3 Series Stainless Steel Spring: 3 Series Stainless Steel Retaining Ring: Nylon, temperature limit 93 Retainer: Passivated and/or tested per STM 38 Screw: Passivated and/or tested per STM 38 Spring: Natural Finish For use in: P Boards PRT NUMBR DSIGNTION PFK M3 4 ll dimensions are in millimeters. Installation Data page 33. Performance Data page 41. Screw Min. Hole Size Min. Dist. G H P T1 T Size x Length (Shank) Sheet In Sheet 2 Hole/L ±.8 ±.25 ±.4 ±.13 ±.64 Max. Nom. Pitch Max. Thickness +.8 To dge M3 x.5 PFK M Size Screw Length PF-26 Pennngineering

27 VLU-DDD PBILITIS VLU-DDD PBILITIS T Solutions Tight Seal Solutions Use PF11PM captive panel screw and TPXS pin in conjunction to satisfy the requirements of the PIMG 3. of the dvanced T. onsider adding an o-ring to our PM..P.S. captive panel screw. When fastened, it provides a tight seal above the panel. Nylon Locking Patch -forming Opportunity Pennngineering is official licensee for RMFORM, TPTIT, PT, and DLT PT fastener products. Nylon locking patch is available to be added to any of PM captive panel screws for applications requiring a locking element. RMFORM and TPTIT are trademarks of RMIN. PT and DLT PT are trademarks of JOT. M nti ross-thread Technology Pennngineering is a licensee of M nti ross-ing Technology. This unique design allows the threads to self-align and drive easily with reduced effort. This helps speed assembly, reduce or eliminate failures, repairs, scrap, downtime, and warranty service associated with thread damage. This option is available on most types of PM captive panel screws. M is a registered trademark of M inc. nti ross- Feature Pennngineering PF-27

28 PTIV PNL SRW INSTLLTION INSTLLTION NOTS For best results we recommend using a PMSRTR press for installation of PM self-clinching fasteners. Please check our website for more information. Visit the nimation Library on our website to view the installation process for this product. PF11 /PF12 /PF11M /PF12M /PM..P.S. FSTNRS 1. Prepare properly sized mounting hole in sheet. Do not perform any secondary operations such as deburring. 2. Place fastener into recessed anvil, and place workpiece (preferably the punch side) over shank of fastener. 3. With installation punch and anvil surfaces parallel, apply squeezing force until the shoulder of the retainer comes in contact with the sheet material. PMSRTR Installation Tooling (1) Max. Screw xtension Dia. +2 mm PUNH nvil Dimensions (mm) nvil Part Punch Part ±.5 ±.5 Number Number M M M M M NVIL (1) Punches and anvils should be hardened. PF11MF /PF12MF FSTNRS (flare-mount installation) 1. Prepare properly sized mounting hole in sheet with countersink. 2. Place fastener into recessed anvil, and place workpiece over shank of fastener. 3. With installation punch and anvil surfaces parallel, apply squeezing force to flare the retainer of the fastener. BFOR INSTLLTION PUNH FTR INSTLLTION PMSRTR Installation Tooling (1) nvil Dimensions (mm) Punch Dimensions (mm) F nvil Punch ±.5 ± ±.5 Part No. Part No. M M M M mm Min. NVIL PUNH DTIL (1) Punches and anvils should be hardened..38mm ±.1mm OUNTRSINK DTIL 9 Nom. 9 Nom. Mounting Hole Dia. (see page 6) F PF-28 Pennngineering

29 PTIV PNL SRW INSTLLTION PF11MW /PF12MW FSTNRS 1. Prepare properly sized mounting hole in sheet. 2. Place fastener into recessed anvil, place workpiece over shank of fastener, then place the washer over the shank of the fastener. 3. With installation punch and anvil surfaces parallel, apply squeezing force with flaring punch. Max. Screw xtension PNL PUNH WSHR NVIL.254mm R Max..8mm R Max. FLRING PUNH DTIL I F G PMSRTR Installation Tooling (1) H nvil Dimensions (mm) Punch Dimensions (mm) F G H I nvil Punch ±.5 ± ±.3 ±.8 Min. ±.1 Part No. Part No. M M M M M (1) Punches and anvils should be hardened. PFHV FSTNRS 1. Prepare properly sized mounting hole in sheet. Do not perform any secondary operations such as deburring. 2. Place fastener into recessed anvil, and place workpiece (preferably the punch side) over shank of fastener. 3. With installation punch and anvil surfaces parallel, apply squeezing force until the shoulder of the retainer comes in contact with the sheet material. Max. Screw xtension Dia. +2 mm PUNH PMSRTR Installation Tooling (1) nvil Dimensions (mm) nvil Part Punch Part ±.5 ±.5 Number Number M M M NVIL (1) Punches and anvils should be hardened. Pennngineering PF-29

30 PTIV PNL SRW INSTLLTION PF7M FSTNRS 1. Prepare properly sized mounting hole in sheet. Do not perform any secondary operations such as deburring. 2. Place fastener into recessed anvil, and place workpiece (preferably the punch side) over the shank of fastener. 3. With installation punch and anvil surfaces parallel, apply squeezing force until the shoulder of the retainer comes in contact with the sheet material. PMSRTR Installation Tooling (1) Max. Screw xtension Dia. +2mm PUNH.51 mm x 45 Nom. nvil Dimensions (mm) nvil Punch Part Part ±.5 ±.5 Number Number M M NVIL (1) Punches and anvils should be hardened. BFOR INSTLLTION FTR INSTLLTION PF7MF FSTNRS (flare-mount installation) PUNH 1. Prepare properly sized mounting hole in sheet with countersink. Do not perform any secondary operations such as deburring. 2. Place fastener into recessed anvil, and place workpiece over the shank of fastener. 3. With installation punch and anvil surfaces parallel, apply squeezing force to flare the retainer of the fastener. Max. Screw xtension.51mm x 45 Nom. NVIL PUNH DTIL PMSRTR Installation Tooling (1) nvil Dimensions (mm) Punch Dimensions (mm) F nvil Punch ±.5 ± ±.5 Part No. Part No. M M (1) Punches and anvils should be hardened. OUNTRSINK DTIL 9 Nom. 9 Nom. F Mounting Hole Dia. (see page 11).38mm ±.1mm PF-3 Pennngineering

31 PTIV PNL SRW INSTLLTION PF3 /PF31 /PF32 FSTNRS 1. Prepare properly sized mounting hole in sheet. Do not perform any secondary operations such as deburring. 2. Place fastener into recessed anvil, and place workpiece (preferably the punch side) over shank of fastener. 3. With installation punch and anvil surfaces parallel, apply squeezing force until the shoulder of the retainer comes in contact with the sheet material. Max. Screw xtension Dia. +2mm PUNH PMSRTR Installation Tooling (1) nvil Dimensions (mm) nvil Part Punch Part ±.5 ±.5 Number Number M M M M NVIL (1) Punches and anvils should be hardened. PF5 /PF51 /PF52 /PF6 /PF61 /PF62 FSTNRS 1. Prepare properly sized mounting hole in sheet. Do not perform any secondary operations such as deburring. 2. Place fastener into recessed anvil, and place workpiece (preferably the punch side) over shank of fastener. 3. With installation punch and anvil surfaces parallel, apply squeezing force until the shoulder of the retainer comes in contact with the sheet material. Max. Screw xtension Dia. +2mm PUNH PMSRTR Installation Tooling (1) nvil Dimensions (mm) nvil Part Punch Part ±.5 ±.5 Number Number NVIL M M M M M (1) Punches and anvils should be hardened. Pennngineering PF-31

32 PTIV PNL SRW INSTLLTION PF4 FSTNRS 1. Prepare properly sized mounting hole in sheet. Do not perform any secondary operations such as deburring. 2. Place fastener into recessed anvil, and place workpiece (preferably the punch side) over shank of fastener. 3. With installation punch and anvil surfaces parallel, apply squeezing force until the shoulder of the retainer comes in contact with the sheet material. Max. Screw xtension Dia. +2mm PUNH Installation Requirements 1. Sheet hardness must be less than 88 on the Rockwell B scale. 2. Hole punch should be kept sharp to minimize work hardening around hole. 3. Fastener should be installed in punch side of hole. 4. Fastener should not be installed near bends or other highly cold worked areas where sheet hardness may be greater than 88 on the Rockwell B scale. NVIL PMSRTR Installation Tooling (1) nvil Dimensions (mm) nvil Part Punch Part ±.5 ±.5 Number Number M M M (1) Punches and anvils should be hardened. PF2P FSTNRS 1. Prepare properly sized mounting hole in sheet. Do not perform any secondary operations such as deburring. 2. Place fastener into recessed anvil, and place workpiece (preferably the punch side) over shank of fastener. 3. With installation punch and anvil surfaces parallel, apply squeezing force until the shoulder of the retainer comes in contact with the sheet material. PMSRTR Installation Tooling (1) Dia. +2mm nvil Dimensions (mm) nvil Part Punch Part ±.5 ±.5 Number Number M M M Max. Screw xtension PUNH (1) Punches and anvils should be hardened. NVIL PF-32 Pennngineering

33 PTIV PNL SRW INSTLLTION PF2 /PFS2 FSTNRS 1. Prepare properly sized mounting hole in sheet. Do not perform any secondary operations such as deburring. 2. Place fastener into recessed anvil, and place workpiece (preferably the punch side) over shank of fastener. 3. With installation punch and anvil surfaces parallel, apply squeezing force until the shoulder of the retainer comes in contact with the sheet material. Max. Screw xtension Dia. +2mm PUNH PMSRTR Installation Tooling (1) nvil Dimensions (mm) nvil Part Punch Part ±.5 ±.5 Number Number M M M M NVIL (1) Punches and anvils should be hardened. PTL2 /PSL2 FSTNRS Pin Dia. +2mm 1. Prepare properly sized mounting hole in sheet. Do not perform any secondary operations such as deburring. 2. Place fastener into recessed anvil, and place workpiece (preferably the punch side) over shank of fastener. 3. With installation punch and anvil surfaces parallel, apply squeezing force until the shoulder of the retainer comes in contact with the sheet material. Max. Pin xtension PUNH PMSRTR Installation Tooling (1) nvil Dimensions (mm) nvil Part Punch Part ±.5 ±.5 Number Number PTL PSL (1) Punches and anvils should be hardened. NVIL PFK FSTNRS Dia. +2mm 1. Prepare properly sized mounting hole in board. 2. Place fastener into recessed anvil, and place workpiece over shank of fastener. 3. With installation punch and anvil surfaces parallel, apply squeezing force until the shoulder of the retainer comes in contact with the board. Max. Screw xtension PUNH PMSRTR Installation Tooling (1) nvil Dimensions (mm) nvil Part Punch Part ±.5 ±.5 Number Number M NVIL (1) Punches and anvils should be hardened. Pennngineering PF-33

34 PTIV PNL SRW INSTLLTION SBR FSTNRS 1. Prepare properly sized mounting hole in sheet. Do not perform any secondary operations such as deburring. If the hole is punched, be sure to install fastener into punched side of hole. 2. ssemble spring on screw by rotating spring counter clockwise and position assembly into recessed magnetic punch. 3. Position hole in workpiece over retractable anvil pin. 4. With installation punch and anvil surfaces parallel, apply squeezing force on top of the screw head and the underside of the sheet material. The squeezing action forces the displacer of the screw into the sheet, causing it to reduce the mounting hole diameter and captivate the screw. Magnetic Punch (1) Magnetic Punch (1) BFOR J K PMSRTR Installation Tooling (1) Installation Tooling Dimensions (mm) nvil Magnetic Punch J K Part Number Part Number (2) M M (1) Punches and anvils should be hardened. (2) Pneumatic punch may also be used. Please contact our PMSRTR tooling division for punch part numbers. L* +3.18mm Min. NVIL PIN FTR Magnetic Punch (1) NVIL SHT * For L, see page 18. SB /SBJ FSTNRS 1. Prepare properly sized mounting hole in sheet. 2. Place the fastener through mounting hole and into anvil. flat or recessed punch can be used. 3. With installation punch and anvil surfaces parallel, apply squeezing force to the top of the screw head and the underside of the sheet material. The squeezing action forces the shoulder of the screw into the sheet, displacing sheet material, causing it to fill the void under the head and shoulder of the screw. PMSRTR Installation Tooling (1) H Installation Tooling Dimensions (mm) H M M (1) Punches and anvils should be hardened. L* +3.18mm Min. * For L, see page 19. PF-34 Pennngineering

35 PTIV PNL SRW INSTLLTION HSB FSTNR INTO HT SINK 1. Prepare properly sized mounting hole in heat sink. Do not perform any secondary operations such as deburring. If the hole is punched, be sure to install the fastener into the punch side of the hole. 2. Place the head of the screw into the recess of the installation anvil and position assembly into recessed magnetic punch. 3. Place the spring over the shoulder of the screw, maintaining concentricity. 4. Position the heat sink mounting hole over the screw. 5. Bring the heat sink down over the screw and onto the shoulder of the screw. 6. With installation punch and anvil surfaces parallel, apply a squeezing force to the heat sink and the head of the screw. The squeezing action forces the displacer of the screw into the heat sink, causing it to reduce the mounting hole diameter and captivate the screw and spring. PMSRTR Installation Tooling (1) Installation Tooling Dimensions (mm) nvil Punch J Part Number Part Number M (1) Punches and anvils should be hardened. 6.35mm ±.13 BFOR J PUNH FTR NVIL NVIL HSR NUT/STNDOFF 1. Prepare properly sized mounting hole in board. 2. Place fastener into the anvil hole and place the mounting hole over the shank of the fastener as shown in drawing. 3. With installation punch and anvil surfaces parallel, apply squeezing force until shoulder contacts the board. PMSRTR Installation Tooling (1) nvil Dimensions (mm) P nvil Part Punch Part ±.13 Number Number HSR-M PUNH (1) Punches and anvils should be hardened. NVIL P FINL SSMBLY Once the screw and spring are captivated, assemble the heat sink to the circuit board by tightening the screw into the receptacle nut or standoff until the audible click is heard. The screw will continue to rotate, but will no longer be engaged in the threads or continue to actively tighten. Pennngineering PF-35

36 PTIV PNL SRW INSTLLTION PR1 FSTNRS 1. Prepare properly sized mounting hole in sheet. Do not perform any secondary operations such as deburring. 2. Place fastener into the mounting hole. 3. With installation punch and anvil surfaces parallel, apply squeezing force until the retainer is flush in the sheet. PUNH NVIL N1 FSTNRS 1. Prepare properly sized mounting hole in sheet. Do not perform any secondary operations such as deburring. 2. Place fastener into recessed anvil, and place workpiece (preferably the punch side) over shank of fastener. 3. With installation punch and anvil surfaces parallel, apply squeezing force until the shoulder of the nut comes in contact with the sheet material. PUNH PMSRTR Installation Tooling (1) nvil Dimensions (mm) nvil Part Punch Part ±.5 ±.5 Number Number M M M NVIL (1) Punches and anvils should be hardened. SMTPFLSM PTIV PNL SRWS Polyimide patch applied here for vacuum pick up. Solder paste applied to pad on PB. Solder fastener in place using standard surface mount techniques. Installs in retracted/unfastened position SMTPF RTINR Polyimide patch applied here for vacuum pick up. Screw snapped in place. Solder paste applied to pad on PB. Solder fastener in place using standard surface mount techniques. PF-36 Pennngineering

37 PTIV PNL SRW PRFORMN DT (1) PF11 /PF12 /PF11M /PF12M /PM..P.S. FSTNRS Test Sheet Material luminum old-rolled Steel Installation Retainer Pushout Installation Retainer Pushout (kn) (N) (kn) (N) M PF11 M PF12 M M PF11MF FSTNRS Installation Retainer Pullout (kn) (N) M M PF11MF M M PF11MW FSTNRS Test Sheet Material 1.52mm old-rolled Steel Swaging Force Retainer Pullout (N) (N) M M PF11MW M M M PFHV FSTNRS Test Sheet Material luminum old-rolled Steel Installation Retainer Pushout Installation Retainer Pushout (kn) (N) (kn) (N) M PFHV M M (1) Published installation forces are for general reference. ctual set-up and confirmation of complete installation should be made by observing proper seating of fastener as described in the installation steps. Other performance values reported are averages when all proper installation parameters and procedures are followed. Variations in mounting hole size, sheet material, and installation procedure may affect performance. Performance testing this product in your application is recommended. We will be happy to provide technical assistance and/ or samples for this purpose. Pennngineering PF-37

38 PTIV PNL SRW PRFORMN DT (1) PF7M FSTNRS Rec. Min. Test Sheet Material Tightening Screw 552-H34 luminum old-rolled Steel Torque Tensile Installation Retainer Pushout Installation Retainer Pushout (N m) (2) (N) (kn) (N) (kn) (N) PF7M M PF7M M PF7MF FSTNRS Rec. Tightening Min. Screw Retainer Torque Tensile Installation Pullout (N m) (2) (N) (kn) (N) PF7MF M PF7MF M PF3 /PF31 /PF32 FSTNRS Test Sheet Material luminum old-rolled Steel Installation Retainer Pushout Installation Retainer Pushout (kn) (N) (kn) (N) PF3 M PF31 M PF32 M PF3 M PF31 M PF32 M PF3 M PF31 M PF32 M PF32 M (1) Published installation forces are for general reference. ctual set-up and confirmation of complete installation should be made by observing proper seating of fastener as described in the installation steps. Other performance values reported are averages when all proper installation parameters and procedures are followed. Variations in mounting hole size, sheet material, and installation procedure may affect performance. Performance testing this product in your application is recommended. We will be happy to provide technical assistance and/ or samples for this purpose. (2) Torque values shown will produce a preload of 7% minimum tensile with nut factor k equal to.1 PF-38 Pennngineering

39 PTIV PNL SRW PRFORMN DT (1) PF5 /PF51 /PF52 /PF6 /PF61 /PF62 FSTNRS Test Sheet Material luminum old-rolled Steel Installation Retainer Pushout Installation Retainer Pushout (kn) (N) (kn) (N) PF5/PF6 M PF51/PF61 M PF52/PF62 M PF5/PF6 M PF51/PF61 M PF52/PF62 M PF5/PF6 M PF51/PF61 M PF52/PF62 M PF5/PF6 M PF51/PF61 M PF52/PF62 M PF52/PF62 M PF4 FSTNRS Test Sheet Material 34 Stainless Steel Installation Retainer Pushout (kn) (N) M PF4 M M PF2 /PFS2 /PF2P FSTNRS Test Sheet Material luminum old-rolled Steel Installation Retainer Pushout Installation Retainer Pushout (kn) (N) (kn) (N) PF2 PFS2 PF2P M M M M PTL2 /PSL2 FSTNRS PTL2 PSL2 Test Sheet Material luminum old-rolled Steel Installation Retainer Pushout Installation Retainer Pushout (kn) (N) (kn) (N) (1) Published installation forces are for general reference. ctual set-up and confirmation of complete installation should be made by observing proper seating of fastener as described in the installation steps. Other performance values reported are averages when all proper installation parameters and procedures are followed. Variations in mounting hole size, sheet material, and installation procedure may affect performance. Performance testing this product in your application is recommended. We will be happy to provide technical assistance and/or samples for this purpose. Pennngineering PF-39

40 PTIV PNL SRW PRFORMN DT (1) SBR FSTNRS Rec. Min. Test Sheet Material Tightening Screw 552-H34 luminum old-rolled Steel Torque Tensile Installation Pushout Installation Pushout (N m) (2) (N) (kn) (N) (kn) (N) SBR M SBR M SB /SBJ FSTNRS Rec. Min. Test Sheet Material Tightening Screw 552-H34 luminum old-rolled Steel Torque Tensile Installation Pushout Installation Pushout (N m) (2) (N) (kn) (N) (kn) (N) SB / SBJ M SB / SBJ M HSB FSTNRS Test Sheet Material luminum old-rolled Steel Installation Pushout Installation Pushout (kn) (N) (kn) (N) HSB M HSR FSTNRS Test Sheet Material 1.5mm FR-4 Panel Installation (kn) Pushout (N) HSR M (1) Published installation forces are for general reference. ctual set-up and confirmation of complete installation should be made by observing proper seating of fastener as described in the installation steps. Other performance values reported are averages when all proper installation parameters and procedures are followed. Variations in mounting hole size, sheet material, and installation procedure may affect performance. Performance testing this product in your application is recommended. We will be happy to provide technical assistance and/ or samples for this purpose. (2) Torque values shown will produce a preload of 7% minimum tensile (125 ksi / 935 MPa) with nut factor k equal to.1 PF-4 Pennngineering

41 PTIV PNL SRW PRFORMN DT (1) PR1 FSTNRS Test Sheet Material luminum old-rolled Steel Installation Installation (kn) (kn) M PR1 M M N1 FSTNRS Test Sheet Material luminum old-rolled Steel Installation Pushout Installation Pushout (kn) (N) (kn) (N) M N1 M M RLFST SMTPFLSM FSTNRS (2) Min. Rec. Test Sheet Material and Tensile Tightening 1.5 mm P.. Board Size Strength Torque Pull-off (N) (N m) (3) (4) (N) SMTPFLSM-M SMTPFLSM-M RLFST SMTPR RTINR (2) Part Number Test Sheet Material.62 Single Layer RF-4 Pushout (N) TSTING ONDITIONS FOR SMTPFLSM FSTNRS ND SMTPR RTINR Oven High Temp Spokes Board Finish Screen Printer Vias Paste Stencil Quad ZR convection oven 473 F / Spoke Pattern 62% Sn, 38% Pb Ragin Manual Printer None mtech N559LF Sn96.5/3.g/.5u (S35) (SMTPR) lpha VP-39 Sn96.5/3.g/.5u (S35) (SMTPFLSM).67 /.17 mm thick (SMTPR).5 /.13 mm thick (SMTPFLSM) SMTPR-6-1T 718 PFK FSTNRS Test Sheet Material FR-4 Fiberglass Installation Pushout (kn) (N) PFK M (1) Published installation forces are for general reference. ctual set-up and confirmation of complete installation should be made by observing proper seating of fastener as described in the installation steps. Other performance values reported are averages when all proper installation parameters and procedures are followed. Variations in mounting hole size, sheet material, and installation procedure may affect performance. Performance testing this product in your application is recommended. We will be happy to provide technical assistance and/or samples for this purpose. (2) With lead-free paste. verage values of 3 test points. The data presented here is for general comparison purposes only. ctual performance is dependent upon application variables. We will be happy to provide samples for you to install. If required, we can also test your installed hardware and provide you with the performance data specific to your application. (3) Torque values shown will produce a preload of 7% minimum tensile with a nut factor k equal to.1. (4) Failure occurred at the solder joint. Screw retention strength is greater than the retainer. Pennngineering PF-41

42 PTIV PNL SRW PBILITIS MOST OMMONLY USD ND ROMMNDD PTIV MTING HRDWR FOR US WITH PTIV PNL SRWS SLF-LINHING NUTS MTD WITH PTIV PNL SRW (See PM Bulletin L) S/LS/SS/LSS provide load-bearing threads in thin sheets with high pushout and torque-out resistance. SP nuts provide load-bearing threads in stainless steel sheets with a hardness of HRB 9 (Rockwell B scale) / HB 192 (Hardness Brinell) or less. L aluminum nuts are recommended for aluminum sheets with a hardness of HRB 5 (Rockwell B scale) / HB 89 (Hardness Brinell) or less. SMPS nuts are for installation into ultra-thin sheets and can be mounted closer to the edge of a sheet than other self-clinching nuts. SL nuts have a unique TRI-DNT locking feature which meets demanding locking performance requirements. S//4 FLOTING NUTS MTD WITH PTIV PNL SRW (See PM Bulletin L) S (carbon steel) and (3 series stainless steel) floating nuts install into sheets with hardness up to HRB 7 / HB 125 on the Rockwell B scale. 4 (4 series stainless steel) floating nuts install into sheets with hardness up to HRB 88 / HB 183 on the Rockwell B scale. locking versions also available. B/BS BLIND NUTS MTD WITH PTIV PNL SRW (See PM Bulletin B) B/BS nuts are used in applications requiring closed thread ends. Provides barrier to protect threads against foreign matter. Protects internal components from intrusion of screws. F FLUSH NUTS MTD WITH PTIV PNL SRW (See PM Bulletin F) Designed to be completely flush in sheets as thin as 1.5mm. Ideal for applications where a thin sheet requires load-bearing threads but still must remain smooth, with no protrusions on either surface. The hexagonal head ensures high axial and torsional strength. F nuts can be ordered to conform to US NSM45938/4 specifications. P BORD NUTS MTD WITH PTIV PNL SRW (See PM Bulletin K) KF2/KFS2 broaching nuts utilize specially formed axially groves that can be mounted into a hole to provide a permanent, strong, threaded attachment point in P boards. SMTSO surface mount nuts also available. For the best mating hardware for your application please contact our Tech Support line or your local representative. PF-42 Pennngineering