ClearSpan Cedar 12' Wide End Frame Kit with Dutch Door

Transcription

1 ClearSpan Cedar 12' Wide End Frame Kit with Dutch Door Photo may show a different but similar model ClearSpan All Rights Reserved. Reproduction is prohibited without permission. STK # WIDTH ' Revision date:

2 YOU MUST READ THIS DOCUMENT BEFORE YOU BEGIN TO ASSEMBLE THE SHELTER. Thank you for purchasing this ClearSpan End Frame Kit. When properly assembled and maintained, this product will provide years of reliable service. These instructions include helpful hints and important information needed to safely assemble and properly maintain the end frame. Please read these instructions before you begin. If you have any questions during the assembly, contact Customer Service for assistance. SAFETY PRECAUTIONS Wear eye protection. Wear head protection. Wear gloves when handling the materials. Use a portable GFCI (Ground Fault Circuit Interrupter) when working with power tools and cords. Do not climb on the shelter or framing during or after construction. Do not occupy the shelter during high winds, tornadoes, or hurricanes. Provide adequate ventilation if the structure is enclosed. Do not store hazardous materials in the shelter. Provide proper ingress and egress to prevent entrapment. WARNING: The individuals assembling this structure are responsible for designing and furnishing all temporary bracing, shoring and support needed during the assembly process. For safety reasons, those who are not familiar with recognized construction methods and techniques must seek the help of a qualified contractor. ASSEMBLY PROCEDURE Following the instructions as presented will help ensure the proper assembly of your end frame. The steps outlining the assembly are as follows: 3. Verify that all parts are included in the shipment. Notify Customer Service for questions or concerns. Read these instructions and all additional documentation included with the shipment before you begin. Gather the tools, bracing, ladders (and lifts), and assistants needed for assembly. 4. Check the weather before you install the film (if equipped). Do not install covers or panels on a windy or stormy day Assemble the end frame and door (if equipped). Read the care and maintenance information at the end of these instructions. Complete and return all warranty information (if included) as instructed. REQUIRED TOOLS The following list identifies the main tools needed to assemble the end frame. Additional tools and supports may be needed depending on the structure, location, and application. Tape measure or measuring device Variable speed drill and impact driver (cordless with extra batteries works best) Wrenches and impact socket set, or an adjustable wrench Scissors or utility knife Hammers and gloves Ladders, work platforms, and other machinery for lifting designed to work safely at the height of the building and end frame. 2 Revision date:

3 Space below is reserved for customer notes. UNPACK AND IDENTIFY PARTS The following steps will ensure that you have all the necessary parts before you begin to assemble the end frame. Unpack the contents of the shipment and place where you can easily inventory the parts. Refer to the Bill of Materials/Spec Sheets. Verify that all parts listed on the Bill of Materials/Spec Sheets are present. If anything is missing or you have questions, consult the Pictorial Parts Guide and all shelter diagrams for clarification, or contact Customer Service. NOTE: At this time, you do not need to open the plastic bags containing smaller parts such as fasteners and clamps. Revision date:

4 The following graphics and photos will help you identify the different parts of the end frame. Consult the diagrams for additional details. (Some parts are not shown.) FA4482B Tek Screw FAF25PB Phillips Head Screws FAS8 Square Head Screws Nut Setter Connector " Fabric Clip CC " Fabric Clip U-Channel Spring Aluminum U-Channel 4 Revision date:

5 ClearSpan Cedar 12' Wide End Frame Kit with Dutch Door Photo may show a different but similar model. OVERVIEW This section describes assembling your end frame kit. See illustration below to identify main parts of end frame kit Locate the required parts for each assembly procedure. Assemble and attach braces, door jambs and header for the door framing. Prepare and attach end panel film. Install dutch door (if equipped). View as seen from the inside of the shelter. View as seen from the inside of the shelter. Exploded drawings do not show the film end panel. Drawing may show a different but similar model. View as seen from the outside of the shelter. Revision date:

6 1 INSTALL ANGLE ANCHORS Gather the parts: # Angle Anchors View the diagrams to measure and determine the location of the two (2) angle anchors for the two door jambs. 3. Mark the center of the shelter's end rafter by measuring the distance between the two ground posts and dividing in half. Measure 13-7/16" in both directions from the center mark and push the two (2) angle anchors into the ground leaving at least 3" exposed. Anchors must be straight and evenly spaced. Refer to the diagram below. NOTE: Place the anchors so the door jamb sits directly in line with the ground posts. Continue with the information on the following page to assemble and install the door jambs and header. Drawing may show a different but similar model. TOP VIEW Ground Post Door Jamb 13-7/16" 13-7/16" Door Jamb Ground Post Angle Anchor Center Angle Anchor Outside of Shelter Diagram shows position of angle anchors measured from the center mark. * DIAGRAM NOT TO SCALE. 6 Revision date:

7 2 Gather the parts: INSTALL Door jambs AND HEADER Door jambs (#EG12W1200) Door header (#EG00W1201) Square head screws (#FAS8) 05" Fabric clips (#105107) 90 Connectors (#104637) Phillips head screws (#FAF25P) Tek screws (#FA4482) Outside View EG00W1201 EG12W1200 EG12W1200 Angled Anchor Angled Anchor Drawings may show a different but similar model. Consult the diagrams to assemble and attach the two (2) door jambs and header. Gather the two (2) door jambs and the two (2) fabric clips. Attach the fabric clips to the angled ends of the jambs using a FAS8 square head screw. Center the clip on the end brace as shown below. Set assembled door jambs into position by seating the plain end against the angled anchors and clipping the top of the door jambs with the fabric clips onto the rafter. Verify the jambs are straight and evenly spaced. 3. Once in position, secure clips by installing a Tek screw through the clip and into the rafter from the inside of the shelter. Drill a hole through the fabric clip if needed Secure lower ends of the door jambs by installing two square head construction screws through each angle anchor and into the door jamb from the outside of the shelter. If needed, pre-drill the holes through the anchor stake for each FAS8 screw. Measure the door panels and allow for clearances. Using the measurements from the door panels, set door header into position and install using 90 connectors and Phillips head screws. Step 1 FAS8 Step 3 Inside View Step 5 Step 1 & 3 Views are seen from the inside of the shelter. EG12W1200 Tek screw Step 4 Inside of shelter Outside of shelter Step Inside View Measure door panels and install header. Maintain an even gap of approximately 1/4" between the top and bottom of the door and between panels. Ground Level FAS8 EG00W1201 Step 4 Revision date:

8 3 ASSEMBLE AND ATTACH FRAME BRACES Inside View Gather the parts: Frame braces (#EG12W1202) Square head screws (#FAS8) 315" Fabric clips (#CC6212) 90 Connectors (#104637) Phillips head screws (#FAF25P) Tek screws (#FA4482) View the diagrams to assemble and attach the two (2) frame braces. EG12W1202 EG12W1202 Drawing may show a different but similar model. Gather the two (2) frame braces and the two (2) CC6212 fabric clips. Attach each fabric clip to the end of a frame brace using a FAS8 square head screw. Center the clip on the brace end as shown below. Set assembled frame braces into position by seating the plain end against the door jambs and clipping the fabric clip to the ground post. Verify the braces are straight and level. (Push fabric clips into the ground if needed.) 3. Once in position, secure fabric clips by installing a Tek screw through the clip and into the ground post from the inside of the shelter. Drill a hole through the fabric clip if needed. 4. Secure the brace to the door jamb from the inside of the shelter by attaching a 90 connector using FAF25P Phillips head screws. Position connector so it does not contact the anchor stake. Step 1 Step 3 Ground Post FAS8 CC6212 EG12W1202 FA4482B Views are seen from the inside of the shelter. Step 4 FAF25P EG12W1202 EG12W1202 Step 1 & 3 Step 4 Step 4 Step 1 & 3 8 Revision date:

9 4 INSTALL Gather the parts: End panel film FILM END PANELS Poly latch U-channel (#102197) Spring for U-channel (#102198) Tek screws (#FA4482) Poly Latch U-channel and Spring Installed View the diagrams to install the poly latch U-channel and attach the end panel film. Using Tek screws, attach sections of the poly latch U-channel along the outside of the frame base and to the door header as shown in the diagrams. NOTE: If main cover is installed, uninstall the main cover from the U-channel on the end rafter. Reinstall main cover after end film has been installed. End panel installed. View as seen from outside the building. Drawing may show a different but similar model Unfold and position the end film over the end rafter. Drape some of the material over the top rafter leaving enough to reach the ground plus 6" - 12". Center the film so equal excess material is on each side of the shelter. Tape can be used to temporarily hold material in place if needed. Once end film is in position, attach the film to the rafter. Starting at the top of the end rafter and working your way down each side, wiggle the wire spring back and forth to seat the spring into the previously installed U-channel, holding the film in place. Be sure to pull the film tight while working down the end rafter. Install the spring into the U-channel attached to the door header and along the frame base. Pull the film snug while installing the spring. CAUTION: Risk of Injury Always wear eye protection when installing the spring! Step 4 Step Step 1 Ground Level FA4482B Space Tek screws evenly about 24" apart. View as seen from outside the building. Revision date:

10 4 INSTALL FILM END PANELS (continued) Inside View 5. Working from inside the frame, mark a 12"-16" border along the door jambs. (Consult the diagram below.) These 12"-16" flaps are wrapped to the inside of the door frame once the final diagonal cuts are made Using the diagram below as a guide, cut the end panel to remove the section that is shaded. Fold flaps to the inside of the door frame and secure to the jambs by attaching the U-channel over the film using Tek screws. See diagrams on this page and the following page. ATTENTION: Do not wrap the film around the door jambs. Consult the diagram to the right. Drawings may show a different but similar model. Remove the dark shaded portion of the end panel material to create an opening for the door. Header Cut film along header as needed. END PANEL END PANEL 12"-16" 12"-16" Wrap this portion of the end panel to the inside of the door frame and secure with U-Channel and Tek screws. See diagram top right and next page. Door Jamb Door Jamb Cut the film as needed so it wraps to the inside of the frame without tearing. Frame Brace Frame Brace Diagram above shows the end wall and end panel as seen from inside a similar shelter. 10 Revision date:

11 8. 4 INSTALL FILM END PANELS (continued) Next, secure the flaps to the U-channel located inside of the door frame using spring wire. Trim edges if needed CLEARSPAN END FRAME KIT Inside View DO NOT REMOVE TOO MUCH OF THE EXCESS FILM MATERIAL. Some excess end film material the material that extends beyond the U-channel should remain in place so the film can be stretched if needed. U-channel installed to the outside edge of jamb. Edge Tek screw U-channel END PANEL Outside of Shelter Drawings may show a different but similar model. END PANEL DOOR JAMB FA4482B TOP VIEW HEADER DOOR JAMB FA4482B Inside of Shelter Dashed line marks the edge of the film once it is installed. Diagram shows the end wall and end panel as seen from inside the shelter. Revision date:

12 5 INSTALL Gather the parts: DOOR PANELS Door panels (#CG72119A & #CG72119B) All door accessories Square head screws (#FAS8) 90 Connectors (#104637) Phillips head screws (#FAF25P) View the diagrams to install the door panels. 3. Locate the upper door panel and position it in the door opening of the frame. Verify that the side with the 90 Drawings may show a different but similar model. connectors is to the inside of the shelter. NOTE: The door panels can be positioned to swing open from the left or the right. Remove and reattach hinges as needed. Ground Level With the panel in the door opening, attach the hinges to the door jamb using FAS8 square head screws. Locate the lower door panel and position the panel in the door opening and attach the hinges as described in the previous step. ATTENTION: To ensure proper door operation, a 1/4" gap must be maintained between the upper and lower panels and between header at upper panel. 4. With both door panels secured in place, close each panel and attach door handles, door lock, and 2" turn button in the desired location using FAF25P Phillips head screws. Maintain an even gap of approximately ATTENTION: Locking hardware and 1/4" across the bottom of the door and turn button are attached to the bottom between door panels. panel. Steps 1-3 Steps 1-3 Step 4 Step 4 Door handles can be positioned where desired. 12 Revision date:

13 SHELTER CARE AND MAINTENANCE Proper care and maintenance of your ClearSpan building is important. Check the following items periodically to properly maintain your building: Regularly check the main cover and end panels to see that these remain tight and in proper repair. Frequently check the anchoring system and all components. Replace worn or damaged parts immediately. Check all fasteners frequently to verify that these remain tight and in good repair. Do not climb or stand on the building or frame at anytime. Check the door panels and all fasteners to ensure these remain tight and in good condition. To prevent damage or possible injury, do not allow the door panels to remain unlatched or unsecured if they are open. Remove debris and objects that may accumulate on the shelter. Use tools that will not damage the cover when removing debris. Remove snow to prevent excess accumulation. Use tools that will not damage the cover when removing snow. Never allow snow to accumulate on the main cover or to remain against the sides or end panels after it is removed from the main cover. Check the contents of the shelter to verify that nothing is touching the cover or panels that could cause damage. Replace all worn or damaged parts. For replacement or missing parts, call for assistance. CLEARSPAN END FRAME KIT Space below is reserved for customer notes. NOTE: With the exception of Truss Arch buildings, ClearSpan shelters and greenhouses do not have any tested loading criteria. Revision date: