ASSEMBLY INSTRUCTIONS

Transcription

1 2 POSITION MONKEY LADDER SWING A25195 ASSEMBLY INSTRUCTIONS 2.4M 4.1M 2.3M 7.92M WARNING To reduce the risk of serious injury or death, you must read and follow these instructions. Keep and refer to these instructions often and give them to any future owner of this play system. Manufacturer contact information provided below. OBSTACLE FREE SAFETY ZONE m x 7.92 m area requires Protective Surfacing. See page 3. MAXIMUM VERTICAL FALL HEIGHT M CAPACITY - 2 Users Maximum, Ages 3 to 10; Weight Limit 110 lbs. (49.9 kg) per child. RESIDENTIAL HOME USE ONLY. Not intended for public areas such as schools, churches, nurseries, day cares or parks. 1-2 Hrs Two person assembly Europe The Granary, Weathercock Hill Chevington, Bury St Edmunds, Suffolk IP29 5RG North America 375 Sligo Road West. P.O. Box 10 Mount Forest Ontario, Canada N0G 2L1 Australia Unit 6/ Victoria Road Marrickville, Sydney NSW 2204 FR: Pour obtenir la notice de montage dans votre langue, cliquez sur DE: Gehen Sie auf um die Bauanleitung in thre Sprache zu bekommen Table of Contents Warnings and Safe Play Instructions pg. 2 Protective Surfacing Guidelines pg. 3 Instructions for Proper Maintenance...pg. 4 About Our Wood Limited Warranty...pg. 5 Keys to Assembly Success...pg. 6 Metric Conversion Sheets.... pg. 7,8 Part ID...pg. 9 Rev Oct

2 Warnings and Safe Play Instructions CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using this play system. Go over the warnings and safe play instructions regularly with your children and make certain that they understand and follow them. Remember on-site adult supervision is required for children of all ages. SERIOUS HEAD INJURY HAZARD Installation over concrete, asphalt, dirt, grass, carpet and other hard surface creates a risk of serious injury or death from falls to the ground. Install and maintain shock absorbing material under and around play-set as recommended on page 3 of these instructions. COLLISION HAZARD Place play-set on level ground at least 6 feet from any obstruction such as a garage or house, fences, poles, trees, sidewalks, walls, landscape timbers, rocks, pavement, planters, garden borders, overhanging branches, laundry lines, and electrical wires. (See OBSTACLE FREE SAFETY ZONE on cover) CHOKING HAZARD/SHARP EDGES & POINTS Adult assembly required. This product contains small parts and parts with sharp edges and points. Keep parts away from children until fully assembled. WARNING LABEL Owners shall be responsible for maintaining the legibility of the warning labels. WARNING STRANGULATION HAZARD NEVER allow children to play with ropes, clotheslines, pet leashes, cables, chains or cord-like items when using this play-set or to attach these items to play-set. NEVER allow children to wear loose fitting clothing, ponchos, hoods, scarves, capes, necklaces, items with draw-strings, cords or ties when using this play-set. NEVER allow children to wear bike or sport helmets when using this play-set. Failure to prohibit these items, even helmets with chin straps, increases the risk of serious injury and death to children from entanglement and strangulation. TIP OVER HAZARD Choose a level location for the equipment. This can reduce the likelihood of the play set tipping over and loose-fill surfacing materials washing away during heavy rains. DO NOT allow children to play on the play-set until the assembly is complete and the unit is properly anchored. WARNING Safe Play Instructions Observe capacity limitations of your play-set. See front cover. Dress children with well fitting and full foot enclosing footwear. Teach children to sit with their full weight in the center of the swing seat to prevent erratic swing motion or falling off. Check for splintered, broken or cracked wood; missing, loose, or sharp edged hardware. Replace, tighten and or sand smooth as required prior to playing. Verify that suspended climbing ropes, rope ladders, chain or cable are secured at both ends and cannot be looped back on itself as to create an entanglement hazard. On sunny and or hot days, check the slide and other plastic rides to assure that they are not very hot as to cause burns. Cool hot slide and rides with water and wipe dry prior to using. Do not allow children to wear open toe or heel footwear like sandals, flip flops or clogs. Do not allow children to walk, in front, between, behind or close to moving rides. Do not let children twist swing chains or ropes or loop them over the top support bar. This may reduce the strength of the chain or rope and cause premature failure. Do not let children get off rides while they are in motion. Do not permit climbing on equipment when it is wet. Do not permit rough play or use of equipment in a manner for which it was not intended. Standing on or jumping from the roof, elevated platforms, swings, climbers, ladders or slide can be dangerous. Do not allow children to swing empty rides or seats. Do not allow children to go down slide head first or run up slide. 2

3

4 4

5 At the factory we have added water repellent to the stain. This water repellent decreases the amount of water absorption during rain or snow thus decreasing the tension in the wood. Sunlight will break down the water repellent, so we recommend applying a water repellent on a yearly basis (see your local stain and paint supplier for a recommended product). Failure to do so can affect warranty. Also if storing the product before installation, make sure you store out of direct sunlight in a cool dry place. Selwood Products Limited Warranty Selwood Products states that the product is free from defect in materials and workmanship for a period of one (1) year from the original date of purchase. This one (1) year warranty covers all parts including wood, hardware, and accessories. All wood carries a ten (10) year warranty against rot and decay. Refer to the schedule associated with replacement of parts under this Warranty. In addition, the manufacturer will replace any parts within the first 60 days from date of purchase found to be missing from or damaged in the original packaging. This warranty applies to the original owner and registrant and is non-transferable. Regular maintenance is required to assure maximum life and performance of this product and failure by the owner to maintain the product according to the maintenance requirements may void this warranty. Maintenance guidelines are provided in the Owner s Manual provided by Selwood Products. This Limited Warranty does not cover: Labour for any inspection or Labour for replacement of any defective item(s) Incidental or consequential damages Cosmetic defects which do not affect performance or integrity of a part or the entire product Vandalism, improper use, failure due to loading or use beyond the capacities stated in the Assembly Manual. Acts of nature including but not limited to wind, storms, hail, floods, excessive water exposure Improper installation including but not limited to installation on uneven, unlevel, or soft ground Minor twisting, warping, checking, splitting, or any other natural occurring properties of wood that do not affect performance or integrity. Selwood Products states that the product has been designed for safety and quality. Any modifications made to the original product could damage the structural integrity of the unit leading to failure and possible injury. Modification voids any and all warranties and Selwood Products will accept no liability for any modified products or consequences resulting from failure of a modified product. This product is warranted for RESIDENTIAL USE ONLY. Under no circumstance should the product be used in public settings such as schools, churches, playgrounds, parks, daycares and the like. Such use may lead to product failure and potential injury. Any and all public use will void this warranty. Selwood disclaims all other representations and warranties of any kind, expressed or implied. Warranty Part Replacement Schedule: Plastic/Metal/Wood Components: 1 Year Warranty 0-60 days from date from purchase: Free Parts & Free Shipping 61 days to 1 year from purchase: Free Parts + Shipping & Handling Wooden (Wood Rot and Decay Only): 10 Year Warranty 0-60 days from date from purchase: Free Parts & Free Shipping 61 days -10 years from purchase: Free Parts + Shipping & Handling This Warranty gives you specific legal rights. You may have other rights as well which vary from state to state or province to province. This warranty excludes all consequential damages, however, some states do not allow the limitation or exclusion of consequential damages, and therefore this limitation may not apply to you. Complete the registration of your Selwood Product purchase online at: Please refer to the back of this instruction manual for details on how to register your Selwood Products purchase. 5

6 Square Assembly 6

7 SOLO)WAVE DESIGN HARDWARE 5/16"(.31) = 8mm Hex Bolt 5/16" (8mm) Lock Washer 1/4"(0.25) = 6mm Hex Bolt 1/4"(0.25) = 6mm Lag Screw 1/4" (6mm) Flat Washer 5/16" (8mm) Flat Washer 1/4" (6mm) Lock Washer 1/4" (6mm) Flat Washer 5/16" (8mm) T-Nut 1/4" (6mm) T-Nut HARDWARE LENGTH CHART inches vs millimetres ½ ½ ½ ½ ½ 38 1¼ / /8 22 3/4 19 1/ DIAMETER CONVERSION 5/16"(.31) = 8mm Lag Screw 3/8"(.38) = 9.5mm Lag Screw 5/16" (8mm) Flat Washer For example: 1 inch = 25.4mm BOLT DIAMETER 5/16 (0.31) inches 0.31 inches x 25.4mm = 8mm LENGTH CONVERSION 1 inch = 25.4mm 3/8" (9.5mm) Flat Washer For example: BOLT LENGTH 4½ (4.5) inches long 4.5 inches x 25.4mm = 114mm long 7

8 1" SOLO)WAVE DESIGN WOOD PROFILES " " /2" 5/4 x /2" 5/4 x /2" 5/4 x /8" /2" 2 x /2" x /2" /8" /8" /4" /8" /8" /8" 3 3/8" 1/2 x 4 1 x 2 1 x 3 1 x " /2" 5/4 x /8" /8" 2 x /8" /2" 1 x /2" /2" 4 x /2" /8" 2 x 6 Dimensions in brackets [mm] represent millimetres /8" /8" LENGTH CONVERSION 1 inch = 25.4mm 1 x 6 For example: BOARD LENGTH 59¼ (59.25) inches inches x 25.4mm = 1505mm 8

9 Part Identification (Reduced Part Size) S2 (3) #8 x 1-1/2" Wood Screw ( ) S3 S4 (10) #8 x 2-1/2" Wood Screw ( ) (10) #8 x 3" Wood Screw ( ) (21) 5/16" T-Nut ( ) (4) 1/4" T-Nut ( ) (21) 5/16" Lock Washer ( ) (4) 1/4" Flat Washer ( ) (4) 1/4" Lock Washer ( ) G1 G9 (8) Hex Bolt 5/16 x 1-1/2" ( ) 5/16" Lock Washer - 5/16" Flat Washer - 5/16" T-Nut (21) 5/16" Flat Washer ( ) (2) Hex Bolt 5/16 x 2-1/2" ( ) 5/16" Lock Washer - 5/16" Flat Washer - 5/16" T-Nut G10 (6) Hex Bolt 5/16 x 3" ( ) 5/16" Lock Washer, 5/16" Flat Washer - 5/16" T-Nut G11 (1) Hex Bolt 5/16 x 3-1/2" ( ) 5/16" Lock Washer 5/16" Flat Washer - 5/16" T-Nut G5 (3) Hex Bolt 5/16 x 4-1/2" ( ) 5/16" Lock Washer 5/16" Flat Washer - 5/16" T-Nut G7 (2) Hex Bolt 5/16 x 5-1/2" ( ) H7 (4) Hex Bolt 1/4 x 5-1/2" ( ) 1/4" Lock Washer - 1/4" Flat Washer - 1/4" T-Nut 9

10 Part Identification (Reduced Part Size) (2) SW Beam 2 x 6 x 73½" A1 A4 (1) Ground Rail 5/4 x 4 x 93 13/16" A5 (2) End Post 2 x 4 x 83 1/2" A6 (2) End Diagonal 2 x 3 x 73 7/16" A7 (2) Ground Stake 1-1/4 x 1-1/2 x 14" A8 A9 A10 (1) SW Block 4 x 4 x 23" (3) Dowel Tennon 1 1/8" x 18 5/8" (5) Dowel -Tennon 1 1/8" x 15 7/8" A11 (1) Spacer 1 x 4 x Nominal Size 2" x 6" 2" x 4" 2" x 3" 2" x 2" 5/4" x 4" 4" x 4" Actual Size 1½" x 5⅜" 1⅜" x 3⅜" 1⅜" x 2½" 1½" x 1½" 1" x 3½" 3½" x 3½" Hardware at Top of Beam Triangle Plates 4 pk -Green X 42" Belt Swing Yellow Welded chain Hardware at Bottom of Beam Hole Plug (13pk) pk Plastic Swing Hanger Cover pk Swing Hanger Bolt Thru

11 PRODUCT NUMBER: A25195 CARTON I.D. STAMP: (Box 1) CARTON I.D. STAMP: (Box 2) CARTON I.D. STAMP: (Box 3) CARTON I.D. STAMP: (Box 4) CARTON I.D. STAMP: (Box 5) CARTON I.D. STAMP: (Box 6) If you have missing, damaged or require replacement parts DO NOT contact your retailer. Please visit and select the Parts Centre. You can then complete a quick online order form or make direct contact with the Selwood Products Part Team

12 Step 1: Monkey Swing Rail Assembly Note: Pre-drill all holes using a 1/8 drill bit before installing the wood screws. A: Insert 5 (A10) 1-1/8 x 15-7/8 Dowels into (A1) SW Beam as shown in fig Make sure the pilot holes are at the top of each board. B: Make sure shoulder of dowel is against each beam before pre-drilling pilot holes. Drill 1/8 pilot holes through the beams and into the dowels to prevent splitting. (fig 1.2) C: Attach (A10) 1-1/8 x 15-7/8 Dowels to both beams with 2 (S4) #8 x 3 Wood Screws per dowel as shown in fig Fig. 1.1 Top Side showing S4 A10 x 5 A1 S4 A1 Fig. 1.2 Make sure shoulder is against beam before drilling holes A10 Wood Parts 5 x A10 Dowel Tennon 1-1/8 x 15-7/8 2 x A1 SW Beam 2 x 6 x 73-1/2 Hardware 10 x S4 # 8 x 3 Wood Screw 12

13 Step 2: Monkey End Ladder Assembly Part 1 Note: Pre-drill all holes using a 1/8 drill bit before installing the wood screws. A: Insert 3 (A9) 1-1/8 x 18-5/8 Dowels into 2 (A5) End Posts as shown in fig B: Make sure shoulder of dowel is against each post before pre-drilling pilot holes. Drill 1/8 pilot holes through the posts and into the dowel to prevent splitting. (fig. 2.2) C: Attach (A9) 1-1/8 x 18-5/8 Dowels to both posts with 3 (S3) #8 x 2-1/2 Wood Screws per post. One screw is installed from top of the post and the other from the bottom as shown in fig S3 Fig. 2.1 A5 A9 A5 S3 Fig. 2.2 Make sure shoulder is against post before drilling holes A9 Wood Parts Hardware 3 x A9 Dowel Tennon 1-1/8 x 18-5/8 6 x S3 # 8 x2-1/2 Wood Screw 2 x A5 End Post 2 x 4 x 83-1/2 13

14 Step 2: Monkey End Ladder Assembly Part 2 D: To bottom of the posts attach (A4) Ground Rail with 2 (G5) 5/16 x 4-1/2 Hex Bolts (with lock washer, flat washer and t-nut). Be sure to keep the bolts loose. (fig. 2.3) E: Attach 1 (A6) End Diagonal to each end of (A4) Ground Rail with 1 (G9) 5/16 x 2-1/2 Hex Bolt (with lock washer, flat washer and t-nut) per side, keeping the bolts loose. (fig. 2.3 and 2.4) F: Make sure the assembly is square and then attach each (A6) End Diagonal to each (A5) End Post with 1 (G10) 5/16 x 3 Hex Bolt (with lock washer, flat washer and t-nut) per diagonal. G: Tighten all bolts from Step 2. Fig. 2.3 G10 A5 G9 A6 G10 A6 A4 G5 G9 Fig. 2.4 A6 G9 Wood Parts Hardware 1 x A4 Ground Rail 5/4 x 4 x 93-13/16 2 x G9 5/16 x 2-1/2 Hex Bolt (5/16 lock washer, 5/16 flat washer, 5/16 t-nut) 2 x A6 End Diagonal 2 x 3 x 73-7/16 2 x G10 5/16 x 3 Hex Bolt (5/16 lock washer, 5/16 flat washer, 5/16 t-nut) 2 x G5 5/16 x 4-1/2 Hex Bolt (5/16 lock washer, 5/16 flat washer, 5/16 t-nut) 14

15 Step 3: Attach Swing Hangers Fig. 3.3 Make sure triangle is tight against beam Warning: For your child s safety, orientate the swing hangers as shown to ensure your swing will have proper swing motion when installed. Failure to do so could result in premature failure of the swing hanger or swing chain. A: In the holes shown in fig. 3.1 install 2 Bolt-Thru Swing Hangers in both (A1) SW Beam. (fig. 3.1 and 3.2) Make sure the swing hangers are oriented in the direction shown in fig. 3.3 to maintain proper swing motion. Fig. 3.1 A1 Bolt-Thru Swing Hangers Fig. 3.2 Bolt-Thru Swing Hangers A1 Other Parts 1 x Bolt-Thru Swing Hangers (pkg of 4) 15

16 Step 4: Attach Triangle Plates Part 1 A: Place Monkey Swing Rail Assembly on the ground with the Bolt-Thru. Swing Hangers facing up. (fig. 4.1) B: Attach 1 Triangle Plate to the End Ladder side of both (A1) SW Beam, in the places shown in fig. 4.1, using 1 (G1) 5/16 x 1-1/2 Hex Bolt (with lock washer, flat washer and t-nut) in the hole indicated in fig Correct Triangle placement and hole usage is very important. C: Attach 1 (H7) 1/4 x 5-1/2 Hex Bolt (with lock washer, flat washer and t-nut) to the ends of both (A1) SW Beams. The bolts do not attach to anything, but MUST be installed to prevent splitting and checking of wood. (fig. 4.1) Important! End Ladder Side (With Overhang) Fig. 4.1 Bottom Side showing H7 G1 Triangle Plates A1 G1 Hardware 2 x H7 1/4 x 5-1/2 Hex Bolt (1/4 lock washer, 1/4 flat washer, 1/4 t-nut) 2 x G1 5/16 x 1-1/2 Hex Bolt (5/16 lock washer, 5/16 flat washer, 5/16 t-nut) Other Parts 2 x Triangle Plates 16

17 Step 4: Attach Triangle Plates Part 2 If you have purchased a Meadowside refer to fig Otherwise, refer to fig D: Attach 1 Triangle Plate to the Fort side of both (A1) SW Beam using 1 (G1) 5/16 x 1-1/2 Hex Bolt (with lock washer, flat washer and t-nut) in the hole indicated in fig. 4.2 & 4.3. Correct Triangle placement and hole usage is very important. E: Attach 1 (H7) 1/4 x 5-1/2 Hex Bolt (with lock washer, flat washer and t-nut) to the ends of both (A1) SW Beam. The bolts do not attach to anything, but MUST be installed to prevent splitting and checking of wood. (fig.4.2 & 4.3) Fig. 4.2 (Meadowside) H7 G1 Fig. 4.3 Triangle Plate H7 G1 Important! Fort Side (No Overhang) Important! Fort Side (No Overhang) A1 G1 Triangle Plate G1 A1 Fort Side 2x H7 Hardware 1/4 x 5-1/2 Hex Bolt (1/4 lock washer, 1/4 flat washer, 1/4 t-nut) Other Parts 1 x Triangle Plate (pkg of 4) 2x G1 5/16 x 1-1/2 Hex Bolt (5/16 lock washer, 5/16 flat washer, 5/16 t-nut) 17

18 Step 5: Attach End Ladder to Swing Rail If you have purchased a Meadowside fort complete this step and proceed to Step 8M. Otherwise, continue with this step and proceed to next Step. A: Attach End Ladder Assembly to the side of the Swing Rail Assembly with the overhang (fig. 5.1 and 5.2) using 1 (G10) 5/16 x 3 Hex Bolt (with lock washer, flat washer and t-nut) in the top hole of each Triangle Plate and 1 (G1) 5/16 x 1-1/2 Hex Bolt (with lock washer, flat washer and t-nut) in the bottom hole of each Triangle Plate. Make sure Swing End Assembly flares out at an angle. (fig. 5.3) Fig. 5.1 Fig. 5.3 Side with overhang 100 A1 Fig. 5.2 G10 A1 G1 Triangle Plates G10 A5 Hardware 2 x G10 5/16 x 3 Hex Bolt (5/16 lock washer, 5/16 flat washer, 5/16 t-nut) 2 x G1 5/16 x 1-1/2 Hex Bolt (5/16 lock washer, 5/16 flat washer, 5/16 t-nut) 18

19 Step 6: Attach Spacer A: Attach (A11) Spacer (fig. 6.1 and 6.2) using 3 (S2) #8 x 1-1/2 Wood Screws to (F13) Post making sure that (A11) Spacer is flush to outside edge of (F13) Post and tight to (F14) Wall Support. Fig. 6.1 Fig. 6.2 Tight A11 F14 S2 Flush F13 Wood Parts 1 x A11 Spacer 1 x 4 x 6 Hardware 3 x S2 #8 x 1-1/2 Wood Screw 19

20 Step 7: Attach SW Block to Fort Part 1 If you have purchased a 1.2M deck, remove Top Hole Plugs as shown in fig. 7.1 If you have purchased a 1.5M deck, remove Bottom Hole Plugs as shown in fig. 7.2 A: On the Swing Wall Side of the fort remove the 2 (H2) 1/4 x 2 Hex Bolts which attaches the Side Roof/Roof Side and Wall Support to the (F13) Post on the Rock Wall side as shown in fig To remove the t-nut, loosen Hex Bolt, hit head with hammer, this should pop the t-nut out. B: Remove 4 Hole Plugs from (A3) Two Tier Mount. Fig. 7.1 (1.2M Deck Height) F13 Roof Side/Side Roof Pull this bolt and t-nut out Remove Top Hole Plugs (1.2M Deck) A3 Fig. 7.2 (1.5M Deck Height) Remove Bottom Hole Plugs (1.5M Deck) 20

21 Step 7: Attach SW Block to Fort Part 2 C: Attach (A8) SW Block to the Side Roof/Roof Side and Wall Support, through to (F13) Post using 2 (G7) 5/16 x 5-1/2 Hex Bolt (with lock washer, flat washer and t-nut). (fig. 7.3) Fig. 7.3 G7 A8 Notice countersunk F13 hole faces out Hex Bolt Assembly Lock Washer T- Nut Flat Washer He x Bolt Wood Parts 1 x A8 SW Block 4 x 4 x 23 Hardware 2 x G7 5/16 x 5-1/2 Hex Bolt (5/16 lock washer, 5/16 flat washer, 5/16 t-nut) 21

22 Step 8: Connect Monkey Ladder Assembly to Fort If you have purchased a 1.2M deck, use Top Bolt holes as shown in fig. 8.1 If you have purchased a 1.5M deck, use Bottom Bolt holes as shown in fig. 8.2 A: Attach the Swing Rail Assembly to the inside face of (A8) SW Block using 1 (G5) 5/16 x 4-1/2 Hex Bolt (with lock washer, flat washer and t-nut) in the top hole of the Triangle Plate and 1 (G11) 5/16 x 3-1/2 Hex Bolt (with lock washer, flat washer and t-nut) in the bottom hole, as shown in fig. 8.1 & 8.2. B: Attach Swing Rail Assembly to the outside face of the (A3) SW Mount with 1 (G10) 5/16 x 3 Hex Bolt (with lock washer, flat washer and t-nut) in the top hole of the Triangle Plate and 1 (G1) 5/16 x 1-1/2 Hex Bolt (with lock washer, flat washer and t-nut) in the bottom hole, as shown in fig. 8.1 & 8.2. Fig. 8.1 (1.2M Deck Height) G10 A3 G1 G5 G11 Swing Rail Assembly One Rung was removed for clarity G10 A3 G1 A8 Fig. 8.2 (1.5M Deck Height) G11 G5 A8 Hardware G11 1 x 5/16 x 3-1/2 Hex Bolt (5/16 lock washer, 5/16 flat washer, 5/16 t-nut) 1 x G5 5/16 x 4-1/2 Hex Bolt (5/16 lock washer, 5/16 flat washer, 5/16 t-nut) 1 x G10 5/16 x 3 Hex Bolt (5/16 lock washer, 5/16 flat washer, 5/16 t-nut) 1 x G1 5/16 x 1-1/2 Hex Bolt (5/16 lock washer, 5/16 flat washer, 5/16 t-nut) 22

23 Step 8M: Connect Monkey Ladder Assembly to Fort (Meadowside Fort Only) A: Remove previously installed hole plugs from both SW Mounts (2446, 2447), as shown in fig B: Attach the Swing Rail Assembly to the outside face of (2446) SW Mount using 1 (G10) 5/16 x 3 Hex Bolt (with lock washer, flat washer and t-nut) in the top hole of the Triangle Plate and 1 (G1) 5/16 x 1-1/2 Hex Bolt (with lock washer, flat washer and t-nut) in the bottom hole, as shown in fig C: Repeat bolt installation for (2447) SW Mount as shown in fig Fig. 8.3 (Meadowside) Hole Plugs Hole Plugs Fig. 8.4 (Meadowside) 2447 G10 G1 Swing Rail Assembly G G1 Hardware 2 x G10 5/16 x 3 Hex Bolt (5/16 lock washer, 5/16 flat washer, 5/16 t-nut) 2 x G1 5/16 x 1-1/2 Hex Bolt (5/16 lock washer, 5/16 flat washer, 5/16 t-nut) 23

24 Step 9: Attach Swing Ground Stakes A: Drive one (A7) Ground Stake 10-1/2 into the ground at each (A5) End Post and attach with 2 (S3) #8 x 2-1/2 Wood Screws per ground stake. (fig. 9.1 and 9.2) Warning! To prevent tipping and avoid potential injury, stakes must be driven 10-1/2 into ground. Digging or driving stakes can be dangerous if you do not check first for underground wiring, cables or gas lines. Fig. 9.1 Fig. 9.2 A5 10-1/2 In Ground S3 A7 Wood Parts Hardware 2 x A7 Ground Stake 1-1/4 x 1-1/2 x 14 4 x S3 # 8 x2-1/2 Wood Screw 24

25 Step 10: Attach Belt Swings A: Insert flexible Swing Hanger Cover over hook. (fig. 10.1) B: Slide Swing Hanger Cover around hook until at top. (fig. 10.2) C: Hook each swing onto hook. (fig. 10.3) D: Twist and flex Swing Hanger Cover onto open end of hook. (fig. 10.4) Fig Fig Fig Fig Bolt Nut x Nut Bolt Protrudes Bolt is Flush Before playing, check that all hardware is tightened correctly and no bolt threads are protruding. To prevent these sharp edges, we have provided extra flat washers that can eliminate this condition. Periodically check hardware and tighten if required. Add an additional washer if bolt threads start to protrude. Other Parts 2 x Belt Swing 4x Plastic Swing Hanger Covers 25

26 Important Instructions Prior to Play: CAUTION: To reduce risk of injury, remove swings from unit prior to child using monkey bars. Fall zone under monkey bars should be clear of all hazards while being used. 26

27 NOTES 27

28 Register your Product Online To register yourself as the original purchaser of this Selwood Products Swingset / Climbing Frame, please take a few moments to complete the short registration form that will be found online at: Rate and Review Your Product Swingset review is an independent review site established to enable purchasers and users of swingsets, playsets, climbing frames, jungle gyms to review the products they buy. Your review can assist future purchasers to make an educated purchase based on your experiences. Enabling potential purchasers to benefit from other peoples positive and negative experiences in the swingset market is a key aim of Swingset Review. Free communication, posting and reading of reviews providing an easy to use platform to ensure the complication is taken away from purchasing a swingset wherever you live in the world. If you ve got something great to shout about your Swingset then do it on our site, or if you ve got a moan then make it known. Your Swingset purchase experience will assist others in making an informed choice.