SECTION 9: PARTS. Headstock

Transcription

1 SECTION 9: PARTS We do our best to stock replacement parts when possible, but we cannot guarantee that all parts shown are available for purchase. Call (800) or visit to check for availability. Headstock Model G0779 (Mfd. Since 09/14)

2 Headstock Parts List 1 P HEADSTOCK CASTING 5 P GEAR 41T 2 P HEADSTOCK COVER 6 P BALL BEARING 6202ZZ P INT RETAINING RING 62MM 7 P KEY 6 X 6 X 14 4 P INT RETAINING RING 5MM 8 P KEY 6 X 6 X 28 5 P FLANGED END CAP 9 P STEEL BALL 8MM 6 P OIL SEAL 45 X 5 X 10MM 40 P COMPRESSION SPRING 7 P MOTOR 2HP 220V 1-PH 41 P EXT RETAINING RING 18MM 7-1 P MOTOR FAN COVER 42 P KEY 5 X 5 X P MOTOR FAN 4 P SET SCREW M6-1 X P PHLP HD SCR M4-.7 X P SPINDLE SHAFT 7-4 P MOTOR TERMINAL BLOCK 45 P GEAR 25T 7-5 P CONTACT PLATE 46 P GEAR 18T 7-6 P S CAPACITOR 150M 250V 1-5/8 X 47 P GEAR 2T 7-7 P R CAPACITOR 20M 450V 1-5/8 X -1/4 48 P GEAR 4T 7-8 P CENTRIFUGAL SWITCH 49 P GEAR 16T 7-9 P BALL BEARING 6205ZZ (FRONT) 50 P KEY 5 X 5 X P BALL BEARING 6205ZZ (REAR) 51 P KEY 6 X 6 X P CAPACITOR BOX COVER 5 P QUILL 7-12 P FLAT WASHER 4MM 54 P SPINDLE 7-1 P CAPACITOR BOX 55 P TAPERED ROLLER BEARING 0207 P P TAP SCREW M-.5 X P TAPERED ROLLER BEARING 0206 P P PHLP HD SCR M4-.7 X P SPLINED SLEEVE 8 P CAP SCREW M X P GEAR 5T 9 P FLAT WASHER 8MM 59 P EXT RETAINING RING 5MM 10 P HEADSTOCK FACE PLATE 60 P DEPTH ROD MOUNT 11 P DRAWBAR CAP 61 P CYLINDRICAL BOLT M16-2 X P DRAWBAR CAP RUBBER SEAL 62 P HEX NUT M16-2 THIN 1 P CAP SCREW M X 45 6 P DEPTH ROD KNURLED KNOB 14 P TAPER PIN 8 X P DEPTH ROD 15 P SET SCREW M X 10 DOG-PT 65 P DEPTH ROD STOP BLOCK 16 P SET SCREW M X 8 66 P DEPTH POINTER 17 P KEY 6 X 6 X P LOCK WASHER 0MM 18 P OIL FILL PLUG /8" 68 P SPANNER NUT M P HEADSTOCK COVER PLUG 69 P QUILL SEAL (RUBBER) 20 P SPINDLE SPEED LEVER 70 P BUTTON HD CAP SCR M4-.7 X 8 21 P ROLL PIN X P ROLL PIN X P OIL DRAIN PLUG /8" 72 P CAP SCREW M X 0 2 P CAP SCREW M5-.8 X 10 7 P SPACER 24 P BUTTON HD CAP SCR M4-.7 X 8 74 P SPINDLE END CAP 25 P OIL SIGHT GLASS M P SET SCREW M5-.8 X 6 26 P DRIVE SHAFT 76 P SET SCREW M5-.8 X 4 27 P GEAR 14T 77 P WORM GEAR HOUSING 28 P BALL BEARING 600ZZ 78 P WORM SHAFT 29 P BALL BEARING 6007ZZ 79 P WORM SHAFT END BRACKET 0 P KEY 5 X 5 X P SET SCREW M6-1 X 12 1 P IDLER SHAFT 81 P SPACER 2 P GEAR 29T 82 P WORM GEAR P07790 GEAR 5T 8 P PINION SHAFT 4 P GEAR 21T 84 P LEVER HUB Model G0779 (Mfd. Since 09/14) -41-

3 Headstock Parts List (Cont.) 85 P SPRING BASE 107 P OUTSIDE LOCK PLUNGER 86 P SPRING COVER 108 P ADJUSTABLE HANDLE 87 P FLAT COILED SPRING 109 P SPEED RANGE SHIFT SHAFT 88 P KNOB BOLT M X P SPEED RANGE SHIFT LEVER 89 P COMPRESSION SPRING 111 P SPEED RANGE SHIFT FORK 90 P FINE DOWNFEED GRADUATED DIAL 112 P EXT RETAINING RING 12MM 91 P STUD-UDE M X 145, 15, P CAP SCREW M6-1 X P TAPERED HANDLE M , 98L 114 P SHIFT ROD 9 P HANDWHEEL 100MM DIA. 115 P OIL SEAL 12 X 22 X 8 94 P HANDWHEEL HANDLE M6-1 X 10, 65L 116 P SPEED SHIFT SHAFT 95 P CAP SCREW M X P SPEED SHIFT FORK 96 P KNURLED THUMB SCREW M5-.8 X P SPEED SHIFT LEVER 97 P KNOB BUSHING 119 P OIL SEAL 5 X 62 X P KNURLED THUMB SCREW M X P PHLP HD SCR M4-.7 X 6 99 P FLAT HD CAP SCR M6-1 X P SWITCH BOX COVER 100 P PHLP HD SCR M5-.8 X P SWITCH BOX 101 P DOWEL PIN X P ROTARY SWITCH (LEFT, STOP, RIGHT) 102 P KEY 8 X 8 X P FLAT WASHER 4MM 10 P CAP SCREW M5-.8 X P DRAWBAR 7/ P ROLL PIN X P POWER CORD 14G W 80" P LOCK LEVER SHAFT 127 P MOTOR CORD 14G W 12" 106 P INSIDE LOCK PLUNGER -42- Model G0779 (Mfd. Since 09/14)

4 Model G0779 (Mfd. Since 09/14) -4- Column

5 Column Parts List 201 P BASE 224 P PIVOT LOCK HUB M X P COLUMN 225 P LEVER HANDLE M X 8, 75L 20 P TABLE ARM BRACKET 226 P RACK RING BASE 204 P TABLE BRACKET 227 P SET SCREW M X P TABLE 229 P HEX BOLT M16-2 X P HEAD ELEVATION GEAR HOUSING 20 P FLAT WASHER 16MM 207 P COLUMN CAP 21 P HEX NUT M P RACK GUIDE RING 240 P ELEVATION CRANK BRACKET 209 P RACK (HEAD ELEVATION) 241 P WORM GEAR 210 P RACK (TABLE ELEVATION) 242 P SPACER 211 P RACK RING 24 P EXT RETAINING RING 14MM 212 P SET SCREW M X P HELICAL GEAR 15T 21 P CAP SCREW M X P SHAFT 214 P FLAT WASHER 16MM 246 P ELEVATION CRANK 215 P LOCK WASHER 16MM 247 P SET SCREW M X P HEX BOLT M16-2 X P CRANK HANDLE 75MM 217 P FLAT WASHER 12MM 249 P SHOULDER SCREW M X 10, 12 X P TABLE LOCK HUB M X P CAP SCREW M6-1 X P TABLE LOCK HANDLE M X 12, 115L 251 P T-BOLT M14-2 X P T-BOLT M X P FLAT WASHER 14MM 221 P FLAT WASHER 12MM 25 P HEX NUT M P HEX NUT M P CAP SCREW M6-1 X P FLAT WASHER 12MM 255 P COOLANT DRAIN -44- Model G0779 (Mfd. Since 09/14)

6 Accessories P TOOLBOX 08 P HEX WRENCH 4MM 02 P SPINDLE ADAPTER MT-MT2 09 P HEX WRENCH MM 0 P07790 SPINDLE SLEEVE R8-MT 10 P DRILL CHUCK KEY 5/16" STD 11T SD-5/8" 04 P DRILL CHUCK ARBOR R8-B16 11 P DRILL CHUCK 1-1MM B16 05 P WRENCH 17 X 19MM OPEN-ENDS 12 P DRIFT KEY 06 P WRENCH 22 X 24MM OPEN-ENDS 1 P07791 BOTTLE FOR OIL 07 P HEX WRENCH 5MM Model G0779 (Mfd. Since 09/14) -45-

7 To reduce risk of death or serious injury, read manual BEFORE using machine. To get a new manual, call (800) or go to EYE/FACE INJURY HAZARD! Always wear ANSI-approved safety glasses and face shield when using this machine. ENTANGLEMENT HAZARD! Tie back long hair, roll up long sleeves, and remove loose clothing, jewelry, or gloves to prevent getting caught in moving parts. INJURY/SHOCK HAZARD! Disconnect power before adjustments, maintenance, or service. Labels CHECK OIL LEVELS BEFORE USING! x 19mm REFER TO OWNER S MANUAL FOR OIL TYPE AND AMOUNT. G0779 L1 90 RPM L2 210 RPM L 45 RPM H1 670 RPM H RPM H 1970 RPM 54 x 54mm NOTICE Do not exceed gearbox oil level above red dot in center of oil site glass below. 4.5 x 80mm DANGER PANTONE 485 C or RAL 001 WARNING CAUTION COLOR CODES PANTONE 151 C or RAL 2005 PANTONE 109 C NOTICE PANTONE 005 C or RAL 5005 GRIZZLY LOGO RED PANTONE 711C or RAL 020 COPYRIGHT GRIZZLY INDUSTRIAL, INC. FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ARTWORK WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without approval. If artwork changes are required, contact us immediately at manuals@grizzly.com. NOTICE Do not exceed gearbox oil level above red dot in center of oil site glass below. 402 Specifications Motor: 2 HP, 220V, Single-Phase, 60 Hz, 8.6A Motor Speed: 1720 RPM Swing: 2-/8" Distance Spindle to Column: 11-11/16" Distance Spindle to Table: 26-1/2" Spindle Taper: R-8 Spindle Travel: 5" Number of Spindle Speeds: 6 Spindle Speed Range: RPM Vertical Table Travel: 24-/8" Table Swivel Around Column: 60 Drilling Capacity Mild Steel: 1-1/4" Gearhead Fluid Capacity: 4-/4 qt. (Grizzly #T296 or ISO 2 Equivalent) Weight: 706 lbs. Date Mfd. for Grizzly in China S/N MODEL G0779 HEAVY-DUTY 2" GEARHEAD DRILL PRESS To reduce the risk of serious injury when using this machine: 1. Read and understand owner s manual before operating. 2. Always wear approved safety glasses.. Only plug power cord into a grounded outlet. 4. Disconnect power before setting up or servicing. 5. Avoid entanglement with spindle tie back long hair, roll up long sleeves, and DO NOT wear loose clothing, gloves, or jewelry. 6. Properly set up machine before starting. 7. Keep all guards and covers in place during operation. 8. Clamp workpiece to table to prevent rotation. 9. Avoid positioning hands where they could slip into rotating bits. 10. Always remove chuck keys and other tools before starting. 11. Never attempt to slow or stop spindle with hands or tools. 12. Use correct (12/05/14) speeds for drilling accessories and workpiece. 1. Do not operate when tired or under influence of drugs or alcohol. 14. Do not expose to rain or use in wet locations. 15. Prevent unauthorized use by children or untrained users; restrict access or disable machine when unattended. 106 x 175.5mm G0779 Machine Labels B x 19mm Specifications 54 x 54mm Motor: 2 HP, 220V, Single-Phase, 60 Hz, 8.6A Motor Speed: 1720 RPM Swing: 2-/8" Distance Spindle to Column: 11-11/16" Distance Spindle to Table: 26-1/2" Spindle Taper: R-8 Spindle 404 Travel: 5" Number of Spindle Speeds: 6 Spindle Speed Range: RPM Vertical Table Travel: 24-/8" Table Swivel Around Column: 60 Drilling Capacity Mild Steel: /4" x 80mm Gearhead Fluid Capacity: 4-/4 qt. (Grizzly #T296 or ISO 2 Equivalent) Weight: 706 lbs. Mfd. for Grizzly in China Date S/N MODEL G0779 HEAVY-DUTY 2 DRILL PRESS To reduce the risk of serious injury when using this machine: 1. Read and understand owner s manual before operating. 2. Always wear approved safety glasses.. Only plug power cord into a grounded outlet. 4. Disconnect power before setting up or servicing. 5. Avoid entanglement with spindle tie back long hair, roll up lo and DO NOT wear loose clothing, gloves, or jewelry. 6. Properly set up machine before starting. 7. Keep all guards and covers in place during operation. 8. Clamp workpiece to table to prevent rotation. 9. Avoid positioning hands where they could slip into rotating bit 10. Always remove chuck keys and other tools before starting. 11. Never attempt to slow or stop spindle with hands or tools. 12. Use correct speeds for drilling accessories and workpiece. 1. Do not operate when tired or under influence of drugs or alcoh 14. Do not expose to rain or use in wet locations. 15. Prevent unauthorized use by children or untrained users; restrict access or disable machine when unattended. CHECK OIL LEVELS BEFORE USING! WARNING! WARNING! cm in Change spindle speed or rotation direction ONLY when spindle is completely stopped. 406 REFER TO OWNER S MANUAL FOR OIL TYPE AND AMOUNT x 54mm NOTICE Do not exceed gearbox oil level above red dot in center of oil site glass below. 17 x 19mm 4.5 x 80mm GRIZZLY LOGO RED COPYRIGHT GRIZZLY INDUSTRIAL, INC. FOR GRIZZLY MACHINES ONLY! DO NOT REPRODUCE OR CHANGE THIS ART WITHOUT WRITTEN APPROVAL! Grizzly will not accept labels changed without ap artwork changes are required, contact us immediately at 401 P ELECTRICITY LABEL 405 P CHECK OIL LABEL 402 P GEARBOX OIL LEVEL NOTICE 406 P GRIZZLY GREEN TOUCH-UP PAINT 40 P MACHINE ID LABEL 407 P CONTROLS/WARNING LABEL 404 P GRIZZLY BEIGE TOUCH-UP PAINT Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes off or becomes unreadable, the owner of this machine MUST replace it in the original location before resuming operations. For replacements, contact (800) or Model G0779 (Mfd. Since 09/14)