CERTIFICATE OF APPROVAL No. ME 5047 WENG MENG INDUSTRIES SDN BHD

Transcription

1 CERTIFICATE OF APPROVAL No. ME 5047 Lot 11, Jalan 8, Kompleks Perabot Olak Lempit, 42700, Kuala Langat, Selangor Darul Ehsan, Malaysia Tel: Fax: Have been assessed against the requirements of the Technical Schedule(s) denoted below and are approved for use subject to the conditions appended hereto: CERTIFIED PRODUCT Composite doorset 30,60,90, and 120 minutes fire resistance TEST STANDARD SS 332: Singapore Standard \ Specification for Fire Doors BRAND NAME Sandor Series FFD30, FFD60, FFD90 and FFD120 Signed and sealed for and on behalf of Warrington Certification Ltd Sir Ken Knight Issued: 9 th January 2014 Chairman - Management Council Page 1 of 25 Valid to: 8 th January 2019

2 Approved Manufacturing Location Weng Meng Industries Sdn Bhd Lot 11, Jalan 8 Kompleks Perabot Olak Lempit Kuala Langat Selangor Darul Ehsan Malaysia Tel: Fax: yhl@sandor.com.my Website: Information: 1. The performance relates only to the behaviour of the specimen of the element of construction under the particular conditions of test. They are not intended to be the sole criteria for assessing the potential fire performance of the element in use, nor do they reflect the actual behaviour in fires. 2. The door-set assemblies shall be installed and maintained as per the manufacturer s instructions, available from Weng Meng Industries Sdn Bhd. 3. The door-set assemblies shall be mechanically fixed into wall constructions having a fire resistance rating of at least the same period as the door-set assemblies. 4. The approval relates to on-going production. Products shall be identified with the certification mark including the certification number, and the manufacturer s name and the product name or code reference. 5. This approval is applicable to complete door-set assemblies only. 6. For verification of the validity of this certificate or inspection of installed door assemblies, please contact Warrington Certification Ltd. Certification Evidence 1- EWA Report No EWA Report No EWA Report No EWA Report No Page 2 of 25 Signed Issued: 9 th January 2014

3 Door Configuration and Performance 30 minutes integrity and insulation This approval relates to doorsets having leaves with Type 1 cores of Fen, a proprietary fibrereinforced cementitious material, or Type 2 cores of Mieco, with timber framing, plywood facings, and timber lippings, based on: Primary data ECI Audit test: 2011FE0305 Secondary data 54S00870/TSM G63284/SS/YCG S08MEC02630/IHN S08MEC03952/MW 2009FE FE FE0018 with permissible design options as outlined as follows: Leaf panel The general area of the leaf core may generally comprise either 44mm thick Fen material with tubular voids or, solid Fen Lite of at least 36mm thick. All leaves faced with 3mm thick plywood and an optional decorative wood veneer. Leaf sizes Hinge mounted, single-acting, single-leaf, latched doorsets Type 1 leaf core Leaves shall have an overall area not exceeding 2.3m 2, up to a maximum height of 2400mm or a maximum width of 1000mm. Transom panels, with or without transom rails in timber door frames or, without transom rails in steel or Fen door frames, may be up to 1000mm high, providing the overall doorset assembly does not exceed 3500mm high. Page 3 of 25 Signed Issued: 9 th January 2014

4 Leaf sizes Hinge mounted, single-acting, double-leaf, latched and bolted doorsets Type 1 and 2 leaf core Leaves shall have an overall area not exceeding 2.76m 2, up to a maximum height of 2700mm or a maximum width of 1380mm. Transom panels, with or without transom rails in timber door frames or, without transom rails in steel or Fen door frames, may be up to 1000mm high, providing the overall doorset assembly does not exceed 3500mm high. Leaf sizes Floorspring or pivot-mounted, single-leaf, latched and bolted doorsets Type 1 leaf core Leaves up to 2139mm high by 930mm wide. Transom panels, with transom rails in timber frames, may be up to 1000mm high, providing the overall doorset assembly does not exceed 3500mm high. Leaf sizes Floorspring or pivot-mounted, double-leaf, latched and bolted doorsets Type 1 leaf core Leaves up to 2139mm high by 865mm + 865mm wide. Transom panels, with transom rails in timber frames, may be up to 1000mm high, providing the overall doorset assembly does not exceed 3500mm high. Leaf edge lippings Leaves finished on all edges with timber lippings of maximum thickness 9mm Leaf edge lippings shall be of timber of minimum density 650kg/m 3 when the door frame profiles are of steel or, of timber of minimum density 450kg/m 3. Leaf edge lippings shall be of timber of minimum density 450kg/m 3 when the door frame profiles are of timber of minimum density 650kg/m 3. Leaf edge lippings at meeting edges shall be of timber of minimum density 650kg/m 3. Page 4 of 25 Signed Issued: 9 th January 2014

5 Intumescent leaf edge and door frame seals When leaves are hung in timber frames, a Flexiseal intumescent seal of 20mm wide by 2mm thick shall be recessed into the rear face of the lipping at the top and all vertical leaf edges, including both meeting edges of double-leaf doorset. Alternatively, the 20mm by 2mm Flexiseal intumescent seals may be exposed in the outer lipping face, in which case the seals shall be centrally located in the leaf edge. When leaves are hung in steel or Fen frames, an exposed Flexiseal intumescent seal of 30mm wide by 2mm thick shall be fitted in the centre of the leaf edges opposite the frame members. Additional intumescent protection provided at hinge, latch, concealed closer, and flush bolt positions. Exposed Flexiseal intumescent seals may be presented in PVC sleeves and may incorporate integral brush or blade smoke seal profiles. Solid or laminated timber door frames, single or double-leaves, with or without transom panels of leaf construction Solid or laminated timber frames, of single or double-rebated profiles, finished with decorative wood veneer. At least 69mm by 45mm with a rebate of at least 15mm. Steel or aluminium door frames, with transom panels of leaf construction For applications requiring insulation performance, metal door frames shall only be used where fire risk is designated to be from one direction only, in which case doorsets shall open towards the direction of risk. There is no limitation for applications requiring integrity only. Frames may be of mild steel or, stainless steel hollow profiles with an architrave face of at least 21mm wide and providing a rebate at least 15mm, fully grouted with sand:cement mortar. Frames may be clad with 0.5mm wood veneer. Adjustable steel door frame For applications requiring integrity only. Glazed aperture One aperture per leaf of sight size sight size up to 0.132m 2, subject to a maximum height of 700mm and a maximum width of 250mm, glazed with Firelite, Pyroshield Safety Clear wire reinforced glass, Pyran S or, Pyran Platinum. Alternatively, approved proprietary glazing systems may be used. Page 5 of 25 Signed Issued: 9 th January 2014

6 Air transfer grilles Either one LVV40 or, one LVC40 air transfer grille by Lorient Polyproducts fitted per leaf. Decorative finishes Leaves and frames may be finished on all faces and edges with 0.5mm thick wood veneer or, with pvc foil up to 0.5mm thick. Leaf faces and timber door frames, excluding leaf edges and frame rebate faces, may be clad with melamine laminate or Acrovyn. Acrovyn shall not be applied to glazed leaves, unless the glass is fully insulated. Decorative effects Routed designs, timber inlay, planted mouldings and panels. Ironmongery Mortice lock cases, forends, strikes, flush bolts, door viewers, and hinge blades shall be bedded on intumescent material. Alternative mortice lock cases, forends, strikes, flush bolts, and hinge blades shall not exceed the approved dimensions. For latches, the forend shall not exceed 235mm long by 25mm wide, and the body shall not exceed of 20mm wide by 89mm deep. Latch bolts shall be of steel or steel reinforced brass and engage the strikes by at least 12mm. Flush bolts shall be of steel and the shoots shall engage the strikes by at least 12mm. Closers shall have power ratings suited to the weight and size of the door leaf, and shall be capable of fully closing the leaf from any angle and overcoming the latch. Ironmongery shall be supported by mechanical test data in accordance with the relevant Annexe of SS 332: Acceptable alternative ironmongery includes: Pbs 9817 st/st door selector, with plastic roller Pbs st/st 2BB butt hinge, 127mm by 89mm by 3mm Pbs 200/300mm by 20mm boxed flush bolt Lockwood/Yale 3800 series V1-3 mortice lock Lockwood/Yale H-01 lever handle Lockwood/Yale G38/CT/30/35SSS thumb turn cylinder Vachette V5 thumb turn cylinder Lockwood H-01 LK20636 st/st lever handle Page 6 of 25 Signed Issued: 9 th January 2014

7 Lockwood 570 cylinder for 3500 series lock case Yale Gateman key cylinder Yale 520 series mortice lock case, cylinder operated Vachette 450 series mortice lockset Lockwood/Yale S-01 st/st lever handle Lockwood/Yale 127mm x 89mm by 3mm 2BB s/s butt hinge Lockwood DC2013 overhead surface mounted door closer Lockwood EV200 overhead surface mounted door closer Rapid pivots, and Dorma BTS80 or Geze TS500/550 floorsprings Shall be fitted in combination with appropriate intumescent materials. The closers shall have power ratings suited to the weight and size of the door leaf, and shall be capable of fully closing the leaf from any angle and overcoming the latch. Hafele DCL 33 overhead concealed closer Closer bodies and slide channel fully bedded in Thermalgel, with the closer body forend rebates fitted with additional lengths of 20mm wide intumescent strip, and then fully coated with nominally 2mm thick Thermalgel. PBS 2000 Roller Mortise Sash lock Roller locks shall only be fitted to doorsets that are normally closed and provide planned access for maintenance and servicing. At all other times, the deadbolts of the locks shall be engaged. Panic devices, push bar/pad type Items shall entirely surface mounted on the door leaves and operate the spindle of an otherwise standard type of mortice latch by means of a push bar or push pad are unrestricted, but require appropriate mechanical test data as required by SS 332: Rod operated and rim panic devices Items shall be supported by appropriate fire and mechanical test data as required by SS 332: 2007 if they replace the tested mortice locks and flush bolts. If there is no supporting test data, rod and rim panic devices shall treated as non-contributory and shall be fitted in addition to the tested and approved mortice locks and flush bolts. Threshold drop down seals Seals shall comprise an aluminium alloy carrier that no wider than 20mm or deeper than 50mm. Carriers shall be fully bedded on intumescent material. Door viewers, maximum diameter 12mm Door viewers shall comprise a steel sleeve and an optical glass lens. For the full thickness of the leaf, the viewer sleeve shall be a friction fit in the leaf or, shall be wrapped in intumescent sheet material or, shall be fully bedded on intumescent sealant of at least 1mm thick. Page 7 of 25 Signed Issued: 9 th January 2014

8 60 minutes integrity and insulation This approval relates to doorsets having leaves with cores of Fen, a proprietary fibre-reinforced cementitious material, timber framing, plywood facings, and timber lippings, based on: Primary data ECI Audit test: 2012FE0018 Secondary data 2009FE FE FE0091 S08MEC03952/MW G63284/SS/YCG S08MEC02630/IHN ECI Audit test: 2011FE0309 with permissible design options as outlined as follows: Leaf panel The general area of the leaf core may generally comprise either 44mm thick Fen material with tubular voids or, solid Fen Lite of at least 36mm thick. All leaves faced with 3mm thick plywood and an optional decorative wood veneer. Leaf sizes for single and double-leaf, latched doorsets Leaves shall have an overall area not exceeding 3.3m 2, up to a maximum height of 2800mm or a maximum width of 1300mm, by at least 50mm thick. Doorsets may include transom panels of door leaf construction as described in 2009FE0062. Transom panels may be up to 1000mm high, providing the overall doorset assembly does not exceed 3500mm high. Leaf edge lippings Leaves may be finished along all edges with timber edge lippings of maximum thickness 9mm and of minimum density 650kg/m 3 with Fen or timber door frames and 900kg/m 3 with steel door frames. Page 8 of 25 Signed Issued: 9 th January 2014

9 Intumescent leaf edge and door frame seals For all applications, a Flexiseal intumescent seal of 20mm wide by 2mm thick shall be recessed into the rear face of the lipping at the top and all vertical leaf edges, including both meeting edges of double-leaf doorset. When leaves are hung in timber frames, a Flexiseal intumescent seal of 20mm wide by 2mm thick shall be fitted in the centre of the frame reveal and may be concealed with a wood veneer up to 3mm thick. As an option, at leaf/frame junctions, the 20mm wide seals concealed in the leaf edges and in the door frame may be replaced by a single 30mm wide exposed seal in either the leaf edge or the door frame. When double-leaf doorsets have square meeting edges, the 20mm wide seals in each meeting edge may be replaced by a single 30mm wide seal in the active meeting edge only. When leaves are hung in steel or Fen frames, an exposed Flexiseal intumescent seal of 30mm wide by 2mm thick shall be fitted in the centre of the leaf edges opposite the frame members.. Exposed Flexiseal intumescent seals may be presented in PVC sleeves and may incorporate integral brush or blade smoke seal profiles. Additional intumescent protection provided at hinge, latch, concealed closer, and flush bolt positions. Solid or laminated timber door frames Single or double-leaves Single or double-rebated solid or laminated timber frames, finished with decorative wood veneer and having an overall profile of least 69mm by 45mm with a rebate of at least 15mm. Fen door frames Single or double-leaves Single or double-rebated frames, finished with decorative wood veneer and having an overall profile of least 69mm by 45mm with a rebate of at least 15mm. Steel door frames for single-leaves For applications requiring insulation performance, metal door frames shall only be used where fire risk is designated to be from one direction only, in which case doorsets shall open towards the direction of risk. Page 9 of 25 Signed Issued: 9 th January 2014

10 There is no limitation for applications requiring integrity only. Frames may be of mild steel or, stainless steel hollow profiles with an architrave face of at least 21mm wide and providing a rebate at least 15mm, fully grouted with sand:cement mortar. Frames may be clad with 0.5mm wood veneer. Adjustable steel door frame For applications requiring integrity only. Glazed aperture One aperture per leaf of sight size sight size up to 0.132m 2, subject to a maximum height of 700mm and a maximum width of 250mm, glazed with Firelite, Pyroshield Safety Clear wire reinforced glass, Pyran S or, Pyran Platinum. Alternatively, approved proprietary glazing systems may be used. Air transfer grille One LVV40, LVC40, LVH44 or, LVHC44 air transfer grille by Lorient Polyproducts per leaf. Decorative finishes Leaves and frames may be finished on all faces and edges with 0.5mm thick wood veneer or, with pvc foil up to 0.5mm thick. Leaf faces and timber door frames, excluding leaf edges and frame rebate faces, may be clad with melamine laminate or Acrovyn. Acrovyn shall not be applied to glazed leaves, unless the glass is fully insulated. Decorative effects Routed designs, timber inlay, planted mouldings and panels. Ironmongery - general All doorsets shall be latched. Alternative mortice lock cases, forends, strikes, flush bolts, and hinge blades shall not exceed the approved dimensions and critical components shall be of steel. Latch bolts shall be of steel or steel reinforced brass and engage the strikes by at least 12mm. Flush bolts shall be of steel and the shoots shall engage the strikes by at least 12mm. Page 10 of 25 Signed Issued: 9 th January 2014

11 Mortice lock cases, forends, strikes, flush bolts, and hinge blades, and concealed hinges shall be bedded on intumescent material. Closers shall have power ratings suited to the weight and size of the door leaf, and shall be capable of fully closing the leaf from any angle and overcoming the latch. Ironmongery specific approved items Ironmongery supported by mechanical test data in accordance with the relevant Annexe of SS 332: 2007 and includes he following items, which may be fitted as direct replacements for the corresponding items as originally tested, and shall be bedded on intumescent materials in a similar manner to the original items being replaced: Pbs 9817 st/st door selector, with plastic roller Pbs st/st 2BB butt hinge, 127mm by 89mm by 3mm Pbs 200/300mm by 20mm boxed flush bolt Lockwood/Yale 3800 series V1-3 mortice lock Lockwood/Yale H-01 lever handle Lockwood/Yale G38/CT/30/35SSS thumb turn cylinder Vachette V5 thumb turn cylinder Lockwood H-01 LK20636 st/st lever handle Lockwood 570 cylinder for 3500 series lock case Yale Gateman key cylinder Yale 520 series mortice lock case, cylinder operated Vachette 450 series mortice lockset Lockwood/Yale S-01 st/st lever handle Lockwood/Yale 127mm x 89mm by 3mm 2BB s/s butt hinge Lockwood DC2013 overhead surface mounted door closer Lockwood EV200 overhead surface mounted door closer Pbs 9817 st/st door selector, with plastic roller Pbs st/st 2BB butt hinge, 127mm by 89mm by 3mm Pbs 200/300mm by 20mm boxed flush bolt Lockwood/Yale 3800 series V1-3 mortice lock Lockwood/Yale H-01 lever handle Lockwood/Yale G38/CT/30/35SSS thumb turn cylinder Vachette V5 thumb turn cylinder Lockwood H-01 LK20636 st/st lever handle Lockwood 570 cylinder for 3500 series lock case Yale Gateman key cylinder Yale 520 series mortice lock case, cylinder operated Lockwood/Yale S-01 st/st lever handle Lockwood/Yale 127mm x 89mm by 3mm 2BB s/s butt hinge Lockwood DC2013 overhead surface mounted door closer Lockwood EV200 overhead surface mounted door closer PBS 127 X 89 X 3mm D46 SS 2BB butt hinge Page 11 of 25 Signed Issued: 9 th January 2014

12 PBS HTH flush bolt PBS 2000 mortise sash lock PBS NL mortise night latch PBS 9817 Door Selector PBS AFB SS auto flush bolt PBS FBB flush bolt ATENA 983 BC overhead surface mounted door closer ATENA 28A BC size 2-5 overhead surface mounted closer ATENA 88 BC size 3 overhead closer Lockwood DCL 34 Size 3 overhead concealed closer Closer bodies and slide channel fully bedded in Thermalgel, with the closer body forend rebates fitted with additional lengths of 20mm wide intumescent strip, and then fully coated with nominally 2mm thick Thermalgel. PBS 2000 Roller Mortise Sash lock Roller locks shall only be fitted to doorsets that are normally closed and provide planned access for maintenance and servicing. At all other times, the deadbolts of the locks shall be engaged. Panic devices, push bar/pad type Items shall entirely surface mounted on the door leaves and operate the spindle of an otherwise standard type of mortice latch by means of a push bar or push pad are unrestricted, but require appropriate mechanical test data as required by SS 332: Rod operated and rim panic devices Items shall be supported by appropriate fire and mechanical test data as required by SS 332: 2007 if they replace the tested mortice locks and flush bolts. If there is no supporting test data, rod and rim panic devices shall treated as non-contributory and shall be fitted in addition to the tested and approved mortice locks and flush bolts. Threshold drop down seals Seals shall comprise an aluminium alloy carrier that no wider than 20mm or deeper than 50mm. Carriers shall be fully bedded on intumescent material. Door viewers, maximum diameter 12mm Door viewers shall comprise a steel sleeve and an optical glass lens. For the full thickness of the leaf, the viewer sleeve shall be a friction fit in the leaf or, shall be wrapped in intumescent sheet material or, shall be fully bedded on intumescent sealant of at least 1mm thick. Page 12 of 25 Signed Issued: 9 th January 2014

13 Acoustic performance Additional materials that may be planted on the closing face of the leaf 1mm thick bonding layer of Green Glue 1mm thick mild steel 3mm thick Cera Ply MgO board 3mm thick plywood Additional seals: Automatic threshold seal, not exceeding 20mm thick by 30mm, fully bedded on intumescent material at least 2mm thick Lorient Finesse combined intumescent and acoustic seal Lorient IS1212K Page 13 of 25 Signed Issued: 9 th January 2014

14 90 minutes This approval relates to doorsets having leaves with cores of Fen, a proprietary mineral based material, based primarily on test data provided by TUV SUD PSB test: 54S075638/ST TUV SUD PSB test: 54S024347/ISM TUV SUD PSB test: S08MEC03952/MW ECI Audit test: 2012FE0012 ECI Audit test: 2011FE0309 with permissible design options as outlined as follows: For 90 minutes integrity only Leaf panel The general area of the leaf core may generally comprise either 44mm thick Fen material with tubular voids or, solid Fen Lite of at least 36mm thick. Leaves faced with 3mm thick plywood or MDF and a decorative wood veneer. Leaf sizes for single-leaf, latched doorsets Leaves shall have an overall area not exceeding 2.8m 2, up to a maximum height of 2500mm or, up to a maximum width of 1200mm, by at least 50mm thick. Leaf edge lippings Leaves may be finished along all edges with timber edge lippings of maximum thickness 6mm and minimum density 900kg/m 3. Intumescent leaf edge seals Flexiseals of 20mm wide shall be fitted centrally in the leaf edges opposite timber composite and Fen frame profiles. Flexiseals at least 30mm wide shall be fitted in leaf edges opposite steel door frames, including the approved adjustable steel frame profile. Page 14 of 25 Signed Issued: 9 th January 2014

15 Flexiseal intumescent seals may be presented in PVC sleeves and may incorporate integral brush or blade smoke seal profiles. Timber composite door frames Laminated timber composite frames, finished with decorative wood veneer. At least 75mm by 45mm with a rebate of at least 15mm. Metal door frames for single-leaf doorsets Aluminium, mild steel or, stainless steel hollow profiles with an architrave face of at least 21mm wide and providing a rebate at least 15mm, fully grouted with sand:cement mortar. Adjustable steel frame for single-leaf doorsets The approved steel frames include a fully grouted adjustable profile that is able to accommodate variations of wall thickness. Fen door frames Frame profiles shall have an architrave face of at least 21mm wide and provide a rebate of at least 15mm. Glazed aperture One aperture per leaf of sight size up to 0.132m 2, subject to a maximum height of 700mm and a maximum width of 250mm glazed with: Keralite, Firelite, Pyran S or, Pyran Platinum. Alternatively, approved proprietary glazing systems may be used. Air transfer grille One LVH44 or LVC44 air transfer grilles by Lorient Polyproducts per leaf. Wood veneer finish Leaves may be finished on all faces and edges with 0.5mm thick wood veneer. Ironmongery Alternative mortice lock cases, forends, strikes, flush bolts, and hinge blades shall not exceed the approved dimensions and critical components shall be of steel. Latch bolts shall be of steel or steel reinforced brass and engage the strikes by at least 12mm. Page 15 of 25 Signed Issued: 9 th January 2014

16 Flush bolts shall be of steel and the shoots shall engage the strikes by at least 12mm. Mortice lock cases, forends, strikes, flush bolts, and hinge blades shall be bedded on intumescent material. Overhead surface mounted closers shall have power ratings suited to the weight and size of the door leaf, and shall be capable of fully closing the leaf from any angle and overcoming the latch. Ironmongery shall be supported by mechanical test data in accordance with the relevant Annexe of SS 332: Acceptable alternative ironmongery includes: Pbs 9817 st/st door selector, with plastic roller Pbs st/st 2BB butt hinge, 127mm by 89mm by 3mm Pbs 200/300mm by 20mm boxed flush bolt Lockwood/Yale 3800 series V1-3 mortice lock Lockwood/Yale H-01 lever handle Lockwood/Yale G38/CT/30/35SSS thumb turn cylinder Vachette V5 thumb turn cylinder Lockwood H-01 LK20636 st/st lever handle Lockwood 570 cylinder for 3500 series lock case Yale Gateman key cylinder Yale 520 series mortice lock case, cylinder operated Vachette 450 series mortice lockset Lockwood/Yale S-01 st/st lever handle Lockwood/Yale 127mm x 89mm by 3mm 2BB s/s butt hinge Lockwood DC2013 overhead surface mounted door closer Lockwood EV200 overhead surface mounted door closer Threshold drop down seals with aluminium carriers that are no wider than 15mm or deeper than 50mm. Carriers shall be bedded on 2mm thick intumescent material. For 90 minutes integrity and insulation Leaf panel The general area of the leaf core may generally comprise either 44mm thick Fen material with tubular voids. Leaves faced with 3mm thick Cera Ply and a decorative wood veneer. Leaf sizes: latched single-leaf doorsets and, latched and bolted double-leaf doorsets All leaves shall have an overall area not exceeding 3.2m 2 per leaf, up to a maximum height of 2800mm or, up to a maximum width of 1300mm, by at least 50mm thick. Page 16 of 25 Signed Issued: 9 th January 2014

17 Leaves of double-leaf doorsets shall be latched and bolted, and of equal width. Leaf edge lippings Single-leaves may be finished along all edges of with timber lippings of maximum thickness 6mm and minimum density 900kg/m 3. Double-leaves may be finished along the hanging and bottom edges with timber lippings of maximum thickness 6mm and minimum density 900kg/m 3. Intumescent leaf edge seals Flexiseals of 20mm wide shall be fitted centrally in the leaf edges opposite timber composite and Fen frame profiles. Flexiseals at least 30mm wide shall be fitted in leaf edges opposite steel door frames, including the approved adjustable steel frame profile. Flexiseal intumescent seals may be presented in PVC sleeves and may incorporate integral brush or blade smoke seal profiles. Timber composite door frames Laminated timber composite frames, finished with decorative wood veneer. At least 75mm by 45mm with a rebate of at least 15mm. Metal door frames for single-leaf doorsets Frames may be of mild steel or, stainless steel hollow profiles with an architrave face of at least 21mm wide and providing a rebate at least 15mm, fully grouted with sand:cement mortar. Frames may be clad with 0.5mm wood veneer. For applications requiring insulation performance, metal door frames shall only be used where fire risk is designated to be from one direction only, in which case doorsets shall open towards the direction of risk. (There is no directional limitation for applications requiring integrity only). Adjustable steel frame for single-leaf doorsets The approved steel frames include a fully grouted adjustable profile that is able to accommodate variations of wall thickness Page 17 of 25 Signed Issued: 9 th January 2014

18 For applications requiring insulation performance, metal door frames shall only be used where fire risk is designated to be from one direction only, in which case doorsets shall open towards the direction of risk. There is no directional limitation for applications requiring integrity only. Fen door frames Frame profiles shall have an architrave face of at least 21mm wide and provide a rebate of at least 15mm. Glazed aperture One aperture per leaf of sight size up to 0.132m 2, subject to a maximum height of 700mm and a maximum width of 250mm glazed with: Keralite, Firelite, Pyran S or, Pyran Platinum. Alternatively, approved proprietary glazing systems may be used. Air transfer grille One LVH44 or LVC44 air transfer grilles by Lorient Polyproducts per leaf. Wood veneer finish Leaves may be finished on all faces and edges with 0.5mm thick wood veneer. Melamine laminate finish Leaves may be clad with decorative melamine laminate up to 1.5mm thick applied only to the faces of leaves. Melamine laminates shall not extend onto the leaf edges or, be applied to door frame profiles. Acrovyn finish Leaves may be clad with Acrovyn up to 1mm thick applied only to the faces of leaves. Acrovyn shall not extend onto the leaf edges or, be applied to door frame profiles, and shall not be applied to door leaves fitted with glazing. Ironmongery Alternative mortice lock cases, forends, strikes, flush bolts, and hinge blades shall not exceed the approved dimensions and critical components shall be of steel. Latch bolts shall be of steel or steel reinforced brass and engage the strikes by at least 12mm. Page 18 of 25 Signed Issued: 9 th January 2014

19 Flush bolts shall be of steel and the shoots shall engage the strikes by at least 12mm. Mortice lock cases, forends, strikes, flush bolts, and hinge blades shall be bedded on intumescent material. Overhead surface mounted closers shall have power ratings suited to the weight and size of the door leaf, and shall be capable of fully closing the leaf from any angle and overcoming the latch. Ironmongery shall be supported by mechanical test data in accordance with the relevant Annexe of SS 332: Acceptable alternative ironmongery includes: Pbs 9817 st/st door selector, with plastic roller Pbs st/st 2BB butt hinge, 127mm by 89mm by 3mm Pbs 200/300mm by 20mm boxed flush bolt Lockwood/Yale 3800 series V1-3 mortice lock Lockwood/Yale H-01 lever handle Lockwood/Yale G38/CT/30/35SSS thumb turn cylinder Vachette V5 thumb turn cylinder Lockwood H-01 LK20636 st/st lever handle Lockwood 570 cylinder for 3500 series lock case Yale Gateman key cylinder Yale 520 series mortice lock case, cylinder operated Vachette 450 series mortice lockset Lockwood/Yale S-01 st/st lever handle Lockwood/Yale 127mm x 89mm by 3mm 2BB s/s butt hinge Lockwood DC2013 overhead surface mounted door closer Lockwood EV200 overhead surface mounted door closer Threshold drop down seals with aluminium carriers that are no wider than 15mm or deeper than 50mm. Carriers shall be bedded on 2mm thick intumescent material. Page 19 of 25 Signed Issued: 9 th January 2014

20 120 minutes This approval relates to doorsets having leaves with cores of Fen, a proprietary mineral based material, based primarily on test data provided by TUV SUD PSB test: 54S075638/ST TUV SUD PSB test: 54S024347/ISM ECI Audit test: 2011FE0309 with permissible design options as outlined as follows: For 120 minutes integrity only Leaf sizes for latched doorsets All leaves shall have an overall area not exceeding 3.2m 2 per leaf, up to a maximum height of 2800mm or, up to a maximum width of 1300mm, by at least 55mm thick. Leaves of double-leaf doorsets shall be latched and bolted, and of equal width. Leaf edge lippings Single-leaves may be finished along all edges of with timber lippings of maximum thickness 6mm and minimum density 900kg/m 3. Double-leaves may be finished along the hanging and bottom edges with timber lippings of maximum thickness 6mm and minimum density 900kg/m 3. Intumescent leaf edge seals Exposed seals of 30mm wide shall be fitted centrally in the leaf edges opposite frame profiles. Meeting edges shall be fitted with an exposed seal of 20mm wide by 2mm thick or, two exposed 10mm by 3mm seals. Metal door frames for single-leaf doorsets Aluminium, mild steel or, stainless steel hollow profiles with an architrave face of at least 21mm wide and providing a rebate at least 15mm, fully grouted with sand:cement mortar. Page 20 of 25 Signed Issued: 9 th January 2014

21 Adjustable steel frame for single-leaf doorsets The approved steel frames include a fully grouted adjustable profile that is able to accommodate variations of wall thickness. Fen door frames Frame profiles shall have an architrave face of at least 21mm wide and provide a rebate of at least 15mm. Glazed aperture One aperture per leaf of sight size up to 0.132m 2, subject to a maximum height of 700mm and a maximum width of 250mm glazed with: Keralite, Firelite, Pyran S or, Pyran Platinum. Alternatively, approved proprietary glazing systems may be used. Air transfer grille One LVH44 or LVC44 air transfer grille by Lorient Polyproducts per leaf. Wood veneer finish Leaves may be finished on all faces and edges with 0.5mm thick wood veneer. Glazed apertures One aperture per leaf of sight size 600mm high by 200mm wide, glazed with Firelite. Alternatively, approved proprietary glazing systems may be used. Ironmongery Alternative mortice lock cases, forends, strikes, flush bolts, and hinge blades shall not exceed the approved dimensions and critical components shall be of steel. Latch bolts shall be of steel or steel reinforced brass and engage the strikes by at least 12mm. Flush bolts shall be of steel and the shoots shall engage the strikes by at least 12mm. Page 21 of 25 Signed Issued: 9 th January 2014

22 Mortice lock cases, forends, strikes, flush bolts, and hinge blades shall be bedded on intumescent material. Closers shall have power ratings suited to the weight and size of the door leaf, and shall be capable of fully closing the leaf from any angle and overcoming the latch. Ironmongery shall be supported by mechanical test data in accordance with the relevant Annexe of SS 332: Acceptable alternative ironmongery includes: Pbs 9817 st/st door selector, with plastic roller Pbs st/st 2BB butt hinge, 127mm by 89mm by 3mm Pbs 200/300mm by 20mm boxed flush bolt Lockwood/Yale 3800 series V1-3 mortice lock Lockwood/Yale H-01 lever handle Lockwood/Yale G38/CT/30/35SSS thumb turn cylinder Vachette V5 thumb turn cylinder Lockwood H-01 LK20636 st/st lever handle Lockwood 570 cylinder for 3500 series lock case Yale Gateman key cylinder Yale 520 series mortice lock case, cylinder operated Vachette 450 series mortice lockset Lockwood/Yale S-01 st/st lever handle Lockwood/Yale 127mm x 89mm by 3mm 2BB s/s butt hinge Lockwood DC2013 overhead surface mounted door closer Lockwood EV200 overhead surface mounted door closer For 120 minutes integrity and insulation Leaf sizes for latched doorsets All leaves shall have an overall area not exceeding 3.2m 2 per leaf, up to a maximum height of 2800mm or, up to a maximum width of 1300mm, by at least 57mm thick. Leaves of double-leaf doorsets shall be latched and bolted, and of equal width. Leaf edge lippings Single-leaves may be finished along all edges of with timber lippings of maximum thickness 6mm and minimum density 900kg/m 3. Double-leaves may be finished along the hanging and bottom edges with timber lippings of maximum thickness 6mm and minimum density 900kg/m 3. Page 22 of 25 Signed Issued: 9 th January 2014

23 Intumescent leaf edge seals Seals of 30mm wide shall be fitted centrally in the leaf edges opposite frame profiles. Meeting edges shall be fitted with a 20mm wide by 2mm thick seal or, two 10mm by 3mm seals. Metal door frames for single-leaf doorsets Frames may be of mild steel or, stainless steel hollow profiles with an architrave face of at least 21mm wide and providing a rebate at least 15mm, fully grouted with sand:cement mortar. Frames may be clad with 0.5mm wood veneer. For applications requiring insulation performance, metal door frames shall only be used where fire risk is designated to be from one direction only, in which case doorsets shall open towards the direction of risk. (There is no directional limitation for applications requiring integrity only). Adjustable steel frame for single-leaf doorsets The approved steel frames include a fully grouted adjustable profile that is able to accommodate variations of wall thickness For applications requiring insulation performance, metal door frames shall only be used where fire risk is designated to be from one direction only, in which case doorsets shall open towards the direction of risk. (There is no directional limitation for applications requiring integrity only). Fen door frames Frame profiles shall have an architrave face of at least 21mm wide and provide a rebate of at least 15mm. Glazed aperture One aperture per leaf of sight size up to 0.132m 2, subject to a maximum height of 700mm and a maximum width of 250mm glazed with: Keralite, Firelite, Pyran S or, Pyran Platinum. Alternatively, approved proprietary glazing systems may be used. Air transfer grille One LVH44 or LVC44 air transfer grille by Lorient Polyproducts per leaf. Page 23 of 25 Signed Issued: 9 th January 2014

24 Wood veneer finish Leaves may be finished on all faces and edges with 0.5mm thick wood veneer. Melamine laminate finish Leaves may be clad with decorative melamine laminate up to 1.5mm thick applied only to the faces of leaves. Melamine laminates shall not extend onto the leaf edges or, be applied to door frame profiles. Acrovyn finish Leaves may be clad with Acrovyn up to 1mm thick applied only to the faces of leaves. Acrovyn shall not extend onto the leaf edges or, be applied to door frame profiles, and shall not be applied to door leaves fitted with glazing. Glazed apertures One aperture per leaf of sight size 600mm high by 200mm wide, glazed with Firelite. Alternatively, approved proprietary glazing systems may be used. Ironmongery Alternative mortice lock cases, forends, strikes, flush bolts, and hinge blades shall not exceed the approved dimensions and critical components shall be of steel. Latch bolts shall be of steel or steel reinforced brass and engage the strikes by at least 12mm. Flush bolts shall be of steel and the shoots shall engage the strikes by at least 12mm. Mortice lock cases, forends, strikes, flush bolts, and hinge blades shall be bedded on intumescent material. Closers shall have power ratings suited to the weight and size of the door leaf, and shall be capable of fully closing the leaf from any angle and overcoming the latch. Ironmongery shall be supported by mechanical test data in accordance with the relevant Annexe of SS 332: Acceptable alternative ironmongery includes: Page 24 of 25 Signed Issued: 9 th January 2014

25 Pbs 9817 st/st door selector, with plastic roller Pbs st/st 2BB butt hinge, 127mm by 89mm by 3mm Pbs 200/300mm by 20mm boxed flush bolt Lockwood/Yale 3800 series V1-3 mortice lock Lockwood/Yale H-01 lever handle Lockwood/Yale G38/CT/30/35SSS thumb turn cylinder Vachette V5 thumb turn cylinder Lockwood H-01 LK20636 st/st lever handle Lockwood 570 cylinder for 3500 series lock case Yale Gateman key cylinder Yale 520 series mortice lock case, cylinder operated Vachette 450 series mortice lockset Lockwood/Yale S-01 st/st lever handle Lockwood/Yale 127mm x 89mm by 3mm 2BB s/s butt hinge Lockwood DC2013 overhead surface mounted door closer Lockwood EV200 overhead surface mounted door closer Threshold drop down seals with aluminium carriers that are no wider than 15mm or deeper than 50mm. Carriers shall be bedded on 2mm thick intumescent material. Page 25 of 25 Signed Issued: 9 th January 2014