CERTIFICATE OF APPROVAL No CF 767 RUTLAND UK

Transcription

1 CERTIFICATE OF APPROVAL No CF 767 This is to certify that, in accordance with TS00 General Requirements for Certification of Fire Protection Products The undermentioned products of Whittington Way, Chesterfield, Derbyshire, S41 9AG Tel: Fax: Have been assessed against the requirements of the Technical Schedule(s) denoted below and are approved for use subject to the conditions appended hereto: CERTIFIED PRODUCT TS.11204, TS.6204 Overhead Door Closers, ITS Concealed Overhead Door Closer and TS.7003 Floor Spring TECHNICAL SCHEDULE TS34 - The Contribution of Controlled Door Closing Devices and Accessories to Fire Resisting Doorsets Signed and sealed for and on behalf of CERTIFIRE Sir Ken Knight Chairman - Management Council Page 1 of 7

2 1. This approval relates to the use of Rutland UK TS power size 3 overhead mounted, slide arm door closing device, the TS.6204 adjustable power 3-4 overhead mounted, projecting arm door closing device, the ITS power size 3 concealed overhead slide arm door closing device and the TS.7003 fixed power size 3 floor mounted door closing device. 2. This certification is designed to demonstrate compliance of the product or system specifically with Approved Document B (England and Wales), Section D of the Technical Standards (Scotland), Technical Booklet E (N. Ireland). If compliance is required to other regulatory or guidance documents there may be additional considerations or conflict to be taken into account. 3. This approval relates to its use with the following door assemblies: - Latched and unlatched, intumescent sealed door assemblies consisting of timber faced and edged leaves with timber, cellulosic or mineral cores in timber frames having a fire resistance up to 120 minutes, subject to individual model s restrictions (CERTIFIRE Code - ITT). 4. The closers are approved on the basis of: i) Initial type testing to EN1154 and BS EN : 2008 ii) An appraisal against TS34 iii) Certification of quality management system to ISO 9001: iv) Inspection and surveillance of factory production control v) Ongoing audit testing in accordance with EN 1154 requirements 5. This approval is applicable only to the specified closers used in the specific fixing position detailed later, with door assemblies of proven fire resistance (as defined in BS EN or BS 476: Part 22: 1987) and having a power rating appropriate to the leaf sizes subject to a minimum size 3 (as specified in BS EN 1154) and including the manufacturer s supplied intumescent protection kit. Failure to supply and install the manufacturer s intumescent protection kit, in the appropriate manner will invalidate this certificate of approval. Additional intumescent frame or door edge protection may also be needed (see scope of approval section). 6. This approval does not cover models with a mechanical hold open facility. 7. The above closers may only be fitted to previously tested door assemblies when fitted in the manner described in this certificate and when particular aspects of the door assembly are maintained. 8. The closer shall only be fitted using the fixings supplied by the closer manufacturer. Page 2 of 7 Signed

3 9. The doorset, including door frame and associated building hardware, should be either CERTIFIRE approved for the relevant application and classification or the doorset, including door frame and associated building hardware, should have achieved at least the required period of fire resistance when tested, or subsequently assessed to EN In either case regard should be paid to the maximum door mass permitted to be used with the closer. 10. The doorset shall be installed in accordance with BS 8214: 2008 where applicable. 11. The approval relates to on going production. Product and/or its immediate packaging is identified with the manufacturer s name, the product name or number, the CERTIFIRE name or name and mark, together with the CERTIFIRE certificate number and application where appropriate. 12. The following tables show acceptable doorsets types and fire resistance periods: Matrix of acceptable doorsets for TS and TS.6204 Key: - approved - Not approved Approved Door Type Class IMM MM TT ITT ITM ITC TM FD20 FD30 FD60 FD120 FD240 E 20 EI 20 E 30 EI 30 E 60 EI 60 E 90 EI 90 E 120 EI 120 E 240 EI 240 Page 3 of 7 Signed

4 Matrix of acceptable doorsets for ITS Approved Door Type Class IMM MM TT ITT ITM ITC TM FD20 FD30 FD60 FD120 FD240 E 20 EI 20 E 30 EI 30 E 60 EI 60 E 90 EI 90 E 120 EI 120 E 240 EI 240 Matrix of acceptable doorsets for double actionts.7003 Key: - approved - Not approved Approved Door Type Class IMM MM TT ITT ITM ITC TM FD20 FD30 FD60 FD120 FD240 E 20 EI 20 E 30 EI 30 E 60 EI 60 E 90 EI 90 E 120 EI 120 E 240 EI 240 Page 4 of 7 Signed

5 Page 5 of 7 Signed CERTIFICATE No. CF 767 See CERTIFIRE Technical Schedules for designation of doorset types i.e. ITT etc. Scope of Approval: All applications apply to unglazed doorsets and glazed doorsets incorporating an uninsulated glass panel size of less than 20% of the leaf area. The closer applications are as referenced in the Classification code section in accordance with EN Use of the ITS for FD30/E30/EI30 applications shall require the following conditions to be met: The door leaf shall have a minimum thickness of 44 mm. The doorset shall be previously proven capable of the required performance when incorporating a similarly sized concealed closing device. The door frame shall be of softwood with a minimum density of 450kg/m 3. The closer shall be fitted in conjunction with an IP.114 intumescent pack as supplied by Rutland UK. Use of the ITS for FD60/E60/EI60 applications shall require the following conditions to be met: The door leaf shall have a minimum thickness of 54 mm and shall be previously proven capable of the required performance when incorporating a similarly sized concealed closing device. The doorset shall be previously proven capable of the required performance when incorporating a similarly sized concealed closing device. The door frame shall be of hardwood with a minimum density of 640kg/m 3. The closer shall be fitted in conjunction with an IP.114 intumescent pack as supplied by Rutland UK. Use of the TS.7003 for FD30/E30/EI30 applications shall require the following conditions to be met: The doorset shall be previously proven in double acting configuration. 1 mm thick Mono ammonium phosphate (MAP) intumescent material shall be fitted into the frame head mortise between the top pivot and the sides of the mortise. 1 mm thick Mono ammonium phosphate (MAP) intumescent material shall be fitted between the underside of the top pivot and its face plate. 2 x 2 mm thicknesses of Mono ammonium phosphate (MAP) intumescent material shall be fitted into the door leaf head mortise between the top strap and the sides of the mortise. 2 mm thick graphite intumescent material shall be bonded to the lower face of the bottom strap. Additionally, the door construction shall be a minimum of 44 mm thick and incorporate minimum 19 mm thick, 640 kg/m 3 density hardwood lippings to all four edges. The minimum level of standard intumescent included within the perimeter of the doorset shall include a single 15 mm by 4 mm seal to the vertical edges or frame jambs and a single 20 mm by 4 mm seal head of the door leaf or frame head (interrupted only at the position of the top strap/top centre).

6 Use of the TS.7003 for FD60/E60/EI60 applications shall require the following conditions to be met: The doorset shall be previously proven in double acting configuration. Mono ammonium phosphate (MAP) intumescent material shall be fitted into the frame head mortise between the top pivot and the sides of the mortise. Mono ammonium phosphate (MAP) intumescent material shall be fitted between the underside of the top pivot and its face plate. 2 x 2 mm thicknesses of Mono ammonium phosphate (MAP) intumescent material shall be fitted into the door leaf head mortise between the top strap and the sides of the mortise. 2 mm thick graphite intumescent material shall be bonded to the lower face of the bottom strap. Where the standard intumescent seals are leaf mounted an additional section of 15 mm (may be reduced to 14 mm) by 4 mm seal shall be fitted centrally to the door jamb extending down from the corner by a minimum of 60 mm and a second section shall be fitted to the frame head extending from the corner out to the edge of the top centre. Where the standard seals are frame mounted the additional sections of seal shall be fitted to the leaf edge at the same relative positions. Additionally, the door construction shall be a minimum of 54 mm thick and incorporate minimum 19 mm thick, 640 kg/m 3 density hardwood lippings to all four edges. The minimum level of standard intumescent included within the perimeter of the doorset shall include two 15 mm by 4 mm seals to the vertical edges and head of the door leaf or mounted within the frame jambs and head (partially interrupted only at the position of the top strap/top centre). These seals shall be positioned 14 mm apart about the centre line of the door such that, where the top strap interrupts them, a residual width of 10 mm of each strip shall be continuous past the strap. When the standard seal configuration cannot provide the same level of bypassing to the top strap when leaf mounted, or top centre when frame mounted, additional intumescent in the form of two 10 mm by 4 mm bypassing strips shall be added. These strips shall extend from 20 mm before the item s mortise to the end of the door head or corner of the frame reveal. The necessary intumescent materials required for the TS.7003 installation shall included in the IP.70 intumescent pack as supplied by Rutland UK. Page 6 of 7 Signed

7 Classification codes - The above approval provides the following classifications: TS in standard fixing position TS.6204 in standard fixing position, with adjustable back check and latch action only ITS in concealed fixing application, with adjustable latch action only TS.7003 double action in standard floor mount fixing application, double action with latch, no back check, 120 max opening Further Information Further information regarding the details contained in this data sheet may be obtained from Rutland UK (Tel: ). Further information regarding the CERTIFIRE certification and other approved products can be obtained from CERTIFIRE (Tel: ) Page 7 of 7 Signed