Assembly of Corner Arbour

Size: px

Start display at page:

Download "Assembly of Corner Arbour"

Bartholomew Lawrence
5 years ago
Views:

1 BUILT AROUND OUR REPUTATION PLEASE NOTE Wood is a natural product and is therefore prone to changes in appearance, including some warping, movement and splitting, particularly during unusual climatic conditions (long hot or wet spells of weather). As a natural occurrence this is not covered by a guarantee. Assembly of Corner Arbour Tools Required Posidrive screwdriver (electric is best) Drill, 6mm drill bit Sandpaper (to smooth any rough edges) Tape measure Step ladder Pencil IMPORTANT! PLEASE READ PRIOR TO ASSEMBLY OF THE BUILDING EVERY PRECAUTION IS TAKEN TO ENSURE THAT YOUR BUILDING HAS NO ELEMENT INCORRECTLY PLACED OR POS- SIBLY HAZARDOUS, HOWEVER PRIOR TO USE PLEASE CHECK ALL SURFACES FOR THE FOLLOWING: 1 RAISED GRAIN, SPLINTERS: sand down timber to smooth finish. 2 NAIL/SCREW/PIN HEADS PROUD: tap home to be flush with surface of timber. 3 DAMAGED SCREW HEADS: RESULTING IN SHARP SPLIN- TERS OF METAL: replace. 4 SHARP ENDS OF NAILS/ SCREWS/PINS PROTRUDING THROUGH THE PANEL: remove and reposition. 5 ENSURE ALL PARTS ARE SECURED AGAINST REASONABLE FORCE: remove and refit. 6 ENSURE THERE ARE NO LOOSE PARTS: remove and refit/discard. WE RECOMMEND THAT PROTECTIVE GLOVES BE WORN THROUGHOUT NOTE: ASSEMBLY INSTRUCTIONS SHOW PANEL `A` WITH SHIPLAP BOARDING. ACTUAL PANELS ARE BOARDED WITH TONGUE AND GROOVED MATCHING. Treatment/Care of your Garden Building Treat with a suitable decorative wood finish immediately. We recommend that all timber pieces be treated again prior to assembly and again within 3 months of assembly. We further recommend that all pieces are treated again at least annually or as frequently as the instructions on the product used recommends. We would suggest that all wall panels be treated in an upside-down position to allow the finish/treatment to ingress into the tongue and groove jointing. We would also remind you that you would rarely (if ever) be able to re-treat the underside of the floor following assembly. We strongly recommend that the underside of the floor is treated an absolute minimum of twice (not including pre-treatment). Garden buildings are not waterproof, therefore on assembling building we recommend using a silicon based sealant between wall panels and between wall panels and floor. Parts List PLEASE LAY OUT PARTS AND CHECK OFF AGAINST CHECK LIST BELOW: QTY DESCRIPTION 2 Back Panels x 1118 mm A 2 Side Panels x 408 mm B 5 Corner Posts - 65 x 65 mm (Bevelled) C 1 Seat Panel Support - 34x34x1118 mm D 1 Seat Panel Support - 34x34x1084 mm E 2 Seat Panel Supports - 34x34x420 mm F 1 SeatPanel G 1 Seat Facia - 653mm Long H 1 Seat Facia - 645mm Long I 1 Roof Bearer Centre Piece - 34x34x165 J 4 Roof Bearers K 4 Roof Braces L 1 Roof Finial M 4 Roof Panels N 1 Seat Back - Left Hand O 1 Seat Back - Right Hand P Thank you and congratulations on the purchase of your Shire Garden Building. We believe that this product will give you many years of excellent service. This is a natural product manufactured to a high standard therefore if you have any queries or experience any difficulties then please contact our customer service hotline on or or Normal office hours: 8.30am to 5.00pm Monday to Friday. Answer phone all other times. Preparation of Base We recommend that the base onto which your building will stand should be at least 75mm larger in each direction than the total floor size of the building. Actual floor area of the building: 1250 x 1250mm Total height clearance: 2500mm The chosen position in your garden for the siting of the building should be excavated to a depth of 75mm to allow a base of sand, on to which paving slabs can be evenly laid - THEY MUST BE LEVEL AND FIRM. EXPLODED VIEW OF PANELS 90 x 60 mm Screws 8 x 50 mm Screws 6 x 25 mm Screws 1 Double Ended Screw 01/03/10

2 Assembly of Building - PLEASE READ INSTRUCTIONS PRIOR TO ASSEMBLY A - Wall Assembly - Step Two A - Wall Assembly - Step One ASSEMBLE ON LEVEL SURFACE TURN COMPLETED ASSEMBLY OVER

3 A - Wall Assembly - Step Three A - Wall Assembly - Step Four

4 A - Wall Assembly - Step Five A - Wall Assembly - Step Six TURN COMPLETED ASSEMBLY OVER

5 A - Wall Assembly - Step Seven A - Wall Assembly - Step Eight

6 B - Seat Assembly - Step One B - Seat Assembly - Step Two

7 B - Seat Assembly - Step Three B - Seat Assembly - Step Four

8 B - Seat Assembly - Step Five C - Roof Assembly - Step One

9 C - Roof Assembly - Step Two C - Roof Assembly - Step Three

10 C - Roof Assembly - Step Four C - Roof Assembly - Step Five

11 C - Roof Assembly - Step Six C - Roof Assembly - Step Seven

12 C - Roof Assembly - Step Eight REPEAT FOR OTHER THREE ROOF PANELS C - Roof Assembly - Step Three COMPLETION CHECKLIST 1 Check and ensure that no raised grain or splinters are evident on timber components. Sand down any raised grain or splinters using fine grade sandpaper. 2 Check that all screw, nail and pin heads are properly tapped home and are not proud of the timber surface. 3 Check and ensure that no screws, nails or pins protrude through any panel. 4 Check and ensure that all parts are properly secured against reasonable force.

BIKE STORE ASSEMBLY INSTRUCTIONS

BIKE STORE ASSEMBLY INSTRUCTIONS AI-BST-28/02/11 Thank you and congratulations on the purchase of your Shire garden building. We believe that this product will give you many years of excellent service.